Oasis MONO Split 3D DC Inverter
Air Conditioner
SERVICE MANUAL
Revision A: 1312030001, Content updated.
Model Numbers:
MS11M-09HRFN1-MW0W
MS11M-24HRDN1-MT0W
MS11M-12HRFN1-MV0W
MS11M-18HRFN1-MU0W
Table of Contents
1.
Precaution
2.
Part Names And Functions
3.
Dimension
4.
Refrigerant Cycle Diagram
5.
Wiring Diagram
6.
Installation Details
7.
Operation Characteristics
8.
Electronic Function
9.
Troubleshooting
10. Exploded View
11. Disassembly Instructions
WARNING
•
Installation MUST conform with local building codes or, in the absence of local codes, with the
National Electrical Code NFPA70/ANSI C1-1993 or current edition and Canadian Electrical
Code Part1 CSA C.22.1.
•
The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments
•
Installation or repairs made by unqualified persons can result in hazards to you and others.
•
Failure to carefully read and follow all instructions in this manual can result in equipment
malfunction, property damage, personal injury and/or death.
•
This service is only for service engineer to use.
Mono 3D
CONTENTS
1. Precaution .....................................................................................................................................................1
1.1 Safety Precaution.......................................................................................................................... 1
1.2 Warning ......................................................................................................................................... 1
2. Part Names And Functions ..........................................................................................................................4
2.1 Model Names of Indoor/Outdoor units.......................................................................................... 4
2.2 Part names of Indoor/Outdoor units ............................................................................................. 4
2.3 Functions of Indoor/Outdoor units ................................................................................................ 5
3. Dimension .....................................................................................................................................................8
3.1 Indoor Unit..................................................................................................................................... 8
3.2 Outdoor Unit ................................................................................................................................ 10
4. Refrigerant Cycle Diagram ........................................................................................................................ 11
5. Wiring Diagram ...........................................................................................................................................12
5.1 Indoor Unit................................................................................................................................... 12
5.2 Outdoor Unit ................................................................................................................................ 14
6 Installation Details .......................................................................................................................................19
6.1 Wrench torque sheet for installation ........................................................................................... 19
6.2 Connecting the cables ................................................................................................................ 19
6.3 Pipe length and the elevation ..................................................................................................... 19
6.4 Installation for the first time ......................................................................................................... 20
6.5 Adding the refrigerant after running the system for many years ................................................ 21
6.6 Re-installation while the indoor unit need to be repaired ........................................................... 21
6.7 Re-installation while the outdoor unit need to be repaired ......................................................... 22
7. Operation Characteristics..........................................................................................................................24
8. Electronic Function ....................................................................................................................................25
8.1 Abbreviation ................................................................................................................................ 25
8.2 Display function........................................................................................................................... 25
8.3 Main Protection ........................................................................................................................... 26
8.4 Operation Modes and Functions................................................................................................. 28
9. Troubleshooting..........................................................................................................................................36
9.1 Indoor Unit Error Display ............................................................................................................ 37
9.2 Outdoor unit error display ........................................................................................................... 38
9.3 Diagnosis and Solution ............................................................................................................... 41
10. Exploded View ..........................................................................................................................................65
10.1 Indoor unit ................................................................................................................................. 65
10.2 Outdoor unit .............................................................................................................................. 73
11 Disassembly Instructions .........................................................................................................................81
11.1 Indoor unit ................................................................................................................................. 81
11.2 Outdoor unit............................................................................................................................... 85
Sharp edges could cause injury, be especially
careful of the case edges and the fins on the
condenser and evaporator.

For installation, always contact the
dealer or an authorized service center.

Do not install the product on a
defective installation stand.

Be sure the installation area does not
deteriorate with age.
If the base collapses, the air conditioner could
fall with it, causing property damage, product
failure, and personal injury.

Do not let the air conditioner run for a
long time when the humidity is very high
and a door or a window is left open.

Take care to ensure that power cable
could not be pulled out or damaged during
operation.
There is risk of fire or electric shock.

Do not place anything on the power
cable.
There is risk of fire or electric shock.

Do not plug or unplug the power
supply plug during operation.
There is risk of fire or electric shock.

Do not touch (operation) the product
with wet hands.

Do not place a heater or other
appliance near the power cable.
There is risk of fire and electric shock.

Do not allow water to run into
electrical parts.
It may cause fire, failure of the product, or
electric shock.

Do not store or use flammable gas or
combustible near the product.
There is risk of fire or failure of product.

Do not use the product in a tightly
closed space for a long time.
Oxygen deficiency could occur.

When flammable gas leaks, turn off
the gas and open a window for ventilation
before turn the product on.

If strange sounds or smoke comes
from product, turn the breaker off or
disconnect the power supply cable.
1. Precaution
1.1 Safety Precaution

To prevent injury to the user or other
people and property damage, the following
instructions must be followed.

Incorrect operation due to ignoring
instruction will cause harm or damage.

Before service the unit, be sure to
read this service manual at first.
1.2 Warning
 Installation

Do not use a defective or underrated
circuit breaker. Use this appliance on a
dedicated circuit.
There is risk of fire or electric shock.

For electrical work, contact the dealer,
seller, a qualified electrician, or an
authorized service center.
Do not disassemble or repair the product,
there is risk of fire or electric shock.

Always ground the product.
There is risk of fire or electric shock.

Install the panel and the cover of
control box securely.
There is risk of fire of electric shock.

Always install a dedicated circuit and
breaker.
Improper wiring or installation may cause
electric shock.

Use the correctly rated breaker of
fuse.
There is risk of fire or electric shock.

Do not modify or extend the power
cable.
There is risk of fire or electric shock.

Do not install, remove, or reinstall the
unit by yourself (customer).
There is risk of fire, electric shock, explosion,
or injury.

Be caution when unpacking and
installing the product.
1
There is risk of electric shock or fire.

Stop operation and close the window
in storm or hurricane. If possible, remove
the product from the window before the
hurricane arrives.
There is risk of property damage, failure of
product, or electric shock.

Do not open the inlet grill of the
product during operation. (Do not touch the
electrostatic filter, if the unit is so equipped.)
There is risk of physical injury, electric shock,
or product failure.

When the product is soaked, contact
an authorized service center.
There is risk of fire or electric shock.

Be caution that water could not enter
the product.
There is risk of fire, electric shock, or product
damage.

Ventilate the product from time to
time when operating it together with a stove
etc.
There is risk of fire or electric shock.

Turn the main power off when
cleaning or maintaining the product.
There is risk of electric shock.

When the product is not be used for a
long time, disconnect the power supply plug
or turn off the breaker.
There is risk of product damage or failure, or
unintended operation.

Take care to ensure that nobody
could step on or fall onto the outdoor unit.
This could result in personal injury and
product damage.
product.
It can avoid vibration of water leakage.

Do not install the product where the
noise or hot air from the outdoor unit could
damage the neighborhoods.
It may cause a problem for your neighbors.

Use two or more people to lift and
transport the product.

Do not install the product where it will
be exposed to sea wind (salt spray) directly.
It may cause corrosion on the product.
Corrosion, particularly on the condenser and
evaporator fins, could cause product
malfunction or inefficient operation.
 Operational

Do not expose the skin directly to
cool air for long time. (Do not sit in the
draft).

Do not use the product for special
purposes, such as preserving foods, works
of art etc. It is a consumer air conditioner,
not a precision refrigerant system.
There is risk of damage or loss of property.

Do not block the inlet or outlet of air
flow.

Use a soft cloth to clean. Do not use
harsh detergents, solvents, etc.
There is risk of fire, electric shock, or damage
to the plastic parts of the product.

Do not touch the metal parts of the
product when removing the air filter. They
are very sharp.

Do not step on or put anything on the
product. (outdoor units)

Always insert the filter securely.
Clean the filter every two weeks or more
often if necessary.
A dirty filter reduces the efficiency of the air
conditioner and could cause product
malfunction or damage.

Do not insert hands or other objects
through air inlet or outlet while the product
is operated.

Do not drink the water drained from
the product.
 CAUTION

Always check for gas (refrigerant)
leakage after installation or repair of
product.
Low refrigerant levels may cause failure of
product.

Install the drain hose to ensure that
water is drained away properly.
A bad connection may cause water leakage.

Keep level even when installing the
2

Use a firm stool or ladder when
cleaning or maintaining the product.
Be careful and avoid personal injury.

Replace the all batteries in the remote
control with new ones of the same type. Do
not mix old and new batteries or different
types of batteries.
There is risk of fire or explosion.

Do not recharge or disassemble the
batteries. Do not dispose of batteries in a
fire.
They may burn of explode.

If the liquid from the batteries gets
onto your skin or clothes, wash it well with
clean water. Do not use the remote of the
batteries have leaked.
3
2. Part Names And Functions
2.1 Model Names of Indoor/Outdoor units
Series
Inverter
Capacity
Indoor units
Outdoor units
9k
MS11M-09HRFN1-MW0W
MOC-09HFN1-MW0W
12k
MS11M-12HRFN1-MV0W
MOC-12HFN1-MV0W
18k
MS11M-18HRFN1-MU0W
MOF-18HFN1-MU0W
24k
MS11M-24HRDN1-MT0W
MOG-24HFN1-MT0W
2.2 Part names of Indoor/Outdoor units
4
2.3 Functions of Indoor/Outdoor units
Filter
Cold catalyst filter
Ionizer(O)
Silent mode(O)
Plasma(O)
Horizontal &Vertical Swing Function(O)
Silver Ico Filter(O)
Louver Position Memory Function
Vitamin C Filter(O)
Refrigerant Leakage Detect
3M HAM Filter(O)
Self-diag. Function
Bio Filter(O)
Hydrophilic Aluminum Fin
Golden Fin(O)
Anti-rust Cabinet
Self Clean(O)
Valve Protection Cover
Follow Me(O)
PTC Heating Belt(O)
1W Standby
Compressor Crankcase Heater
O: optional function
5
•
Cold Catalyst Filter:
Eliminate formaldehyde and other volatile organic compounds as well as harmful gases and odors.
•
Ionizer:
Release negative ions, eliminate odor, dust, smoke and pollen particles to give you fresh and healthy air.
•
Plasma:
Generate a high voltage electrostatic zone, absorb and eliminate dust, smoke and pollen particles. It also
deodorizes air as removing tobacco odours, garbage smells etc.
•
Silver Ion Filter:
Sterilize bacteria effectively by decomposing cell wall of bacteria.
•
Vitamin C Filter:
Release Vitamin C which can eliminate active oxygen to beautify the skin.
•
3M HAM Filter:
Open-hole-structure with charged electrostatic effectively capture dust and particles, ensure maximum air
flow and minimum pressure drop.
•
Bio Filter(O):
Bio filter consists of a specialized biological enzyme and Eco filter. The Eco filter catches very small
airborne dust particles and bacteria, fungi and microbes. Biological enzyme kills bacteria by dissolving their
cell wall thus eliminating the problem of re-pollution.
•
Golden Fin:
The Golden hydrophilic condenser can improve the heating efficiency by accelerating the defrosting
process. The unique anticorrosive golden coating on the condenser can withstand the salty air, rain and
other corrosive elements.
•
Self Clean:
When this function is activated, firstly the indoor unit operates as Fan-only mode with low fan speed, during
this period the condensed water will take some dust on evaporator fins away. After that the unit turns to
heating operation with low fan speed which dries the inside of indoor unit. Finally it turns to fan-only mode
and blows away the wet air. The whole process cleans the internal side of indoor unit and prevents the
breeding of bacteria.
•
Follow me:
With this technology, a temperature sensor is built in the remote control when you stay close to the remote
control, the unit will automatically change the operation mode to supply comfortable temperature just like
the air conditioner is following you.
•
Silent mode
Indoor fan will run at super breeze speed and indoor unit noise level can be extremly low to 20dB(A) when
the unit enters silent mode operation.
•
Horizontal&Vertical Swing Function
The unit has auto horizontal swing and auto vertical swing function, which supplies more even and
comfortable air flow.
•
Louver position memory function:
When starting the unit again after shutting down, its louver will restore to the angle originally set by the user
•
Refrigerant leakage detect:
The refrigerant leakage detect function can better prevent the compressor being
damaged by refrigerant
leakage or compressor overload.
•
Self-diag.Function:
Monitoring some abnormal operations or parts failures, microcomputer of the air conditioner will switch off
and protect the system automatically.Meanwhile, the error or protection code will be displayed on the indoor
6
unit.
•
PTC heating belt:
With a PTC heating belt fitted on the base plate of the outdoor unit, the rain, snow or defrosted water
accumulating on the base plate is avoided.
•
Compressor crankcase heater:
The oil dissolves easily in refrigerant, especially in low temperature condition. The crankcase heating belt
can heat the bottom of the compressor to avoid pumping out too much oil with the refrigerant, which helps
to protect the compressor.
7
3. Dimension
3.1 Indoor Unit
D
W
Model
W
D
H
MS11M-09HRFN1-MW0W
835mm
(32.9in)
198mm
(7.8in)
280mm
(11.0in)
MS11M-18HRFN1-MU0W
990mm
(39.0in)
218mm
(8.6in)
315mm
(12.4in)
MS11M-24HRDN1-MT0W
1186mm
(46.7in)
258mm
(10.2in)
340mm
(13.4in)
MS11M-12HRFN1-MV0W
Model
L
R
H
Dimension of installation hole
MS11M-09HRFN1-MW0W
140mm
(5.5in)
110mm
(4.3in)
45mm
(1.8in)
Φ65mm(2.56in)
MS11M-12HRFN1-MV0W
8
Model
L
R
H
Dimension of installation hole
MS11M-18HRFN1-MU0W
260mm
(10.2in)
135mm
(5.3in)
45mm
(1.8in)
Φ65mm(2.56in)
Model
L
R
H
Dimension of installation hole
MS11M-24HRDN1-MT0W
275mm
(10.8in)
275mm
(10.8in)
45mm
(1.8in)
Φ65mm(2.56in)
9
3.2 Outdoor Unit
More than 30cm(11.8in)
More than 60cm(23.6in)
(Service space)
More than 30cm(11.8in)
Fe
n
ob ce o
sta
r
cle
s
More than 60cm(23.6in)
More than 70cm(27.6in)
Note: The above drawing is only for reference. The appearance of your units may be different.
Model
W
D
H
W1
A
B
MOC-09HFN1-MW0W
760mm
285mm
590mm
823mm
530mm
290mm
MOC-12HFN1-MV0W
(29.9in)
(11.2in)
(23.2in)
(32.4in)
(20.9in)
(11.4in)
845mm
320mm
700mm
908mm
560mm
335mm
(33.3in)
(12.6in)
(27.6in)
(35.7in)
(22.0in)
(13.2in)
900mm
(36.7in)
315mm
(12.9in)
860mm
(35.1in)
980mm
(40in)
590mm
(24.1in)
333mm
(13.6in)
MOF-18HFN1-MU0W
MOG-24HFN1-MT0W
10
4. Refrigerant Cycle Diagram
INDOOR
OUTDOOR
LIQUID SIDE
Electronic
CAPILIARY TUBE expansion valve CAPILIARY TUBE
2-WAY VALVE
T3 Condenser
temp. sensor
HEAT
EXCHANGE
(EVAPORATOR)
HEAT
EXCHANGE
(CONDENSER)
T4 Ambient
temp. sensor
T1 Room temp.
sensor
T2 Evaporator
temp. sensor
GAS SIDE
4-WAY VALVE
3-WAY VALVE
Accumulator
Compressor
T5 Discharge
temp. sensor
COOLING
HEATING
11
5. Wiring Diagram
5.1 Indoor Unit
MS11M-09HRFN1-MW0W, MS11M-12HRFN1-MV0W, MS11M-18HRFN1-MU0W
12
MS11M-24HRDN1-MT0W
13
5.2 Outdoor Unit
MOC-09HFN1-MW0W, MOC-12HFN1-MV0W
14
MOF-18HFN1-MU0W
15
MOG-24HFN1-MT0W
MOC-09HFN1-MW0W, MOC-12HFN1-MV0W
16
MOF-18HFN1-MU0W
17
MOG-24HFN1-MT0W
18
6.3 Pipe length and the elevation
6 Installation Details
Pipe size
6.1 Wrench torque sheet for
installation
Models
Gas
Liquid
3/8in
1/4in
(Ф9.52mm)
(Ф6.35mm)
1/2in
1/4in
(Ф12.7mm)
(Ф6.35mm)
1/2in
1/4in
(Ф12.7mm)
(Ф6.35mm)
5/8in
3/8in
(Ф15.9mm)
(Ф9.52mm)
Additional tightening
Outside diameter
MS11M-09HRFN1-MW0W+MOC-09HFN1-MW0W
Torque
torque
Ф6.35mm
1/4in
Ф9.52mm
3/8in
Ф12.7mm
1/2in
1500N.cm(153kgf.cm)
2500N.cm(255kgf.cm)
1600N.cm(163kgf.cm)
MS11M-12HRFN1-MV0W+MOC-12HFN1-MV0W
2600N.cm(265kgf.cm)
MS11M-18HRFN1-MU0W+MOF-18HFN1-MU0W
3500N.cm(357kgf.cm)
3600N.cm(367kgf.cm)
MS11M-24HRDN1-MT0W+MOG-24HFN1-MT0W
Ф15.9mm
5/8in
4500N.cm(459kgf.cm)
4700N.cm(479kgf.cm)
Ф19mm
3/4in
6500N.cm(663kgf.cm)
6700N.cm(683kgf.cm)
Max.
Standard
Additional
Max.
Length
Models
length
refrigerant
Elevation
A
6.2 Connecting the cables
MS11M-09HRFN1-MW0W+
The power cord should be selected according
MOC-09HFN1-MW0W
7.5m
10m
25m
15g/m
(24.6ft)
(32.8ft)
(82.0ft)
(0.16oz/ft)
7.5m
10m
25m
15g/m
(24.6ft)
(32.8ft)
(82.0ft)
(0.16oz/ft)
7.5m
20m
30m
15g/m
(24.6ft)
(65.6ft)
(98.4ft)
(0.16oz/ft)
7.5m
25m
50m
30g/m
(24.6ft)
(82.0ft)
(164ft)
(0.32oz/ft)
to the following specifications sheet.
MS11M-12HRFN1-MV0W+M
Appliance Amps
AWG Wire Size
10
18
13
16
MS11M-18HRFN1-MU0W+M
18
14
OF-18HFN1-MU0W
25
12
30
10
OC-12HFN1-MV0W
MS11M-24HRDN1-MT0W+M
OG-24HFN1-MT0W
The cable size and the current of the fuse or
switch are determined by the maximum
current indicated on the nameplate which
located on the side panel of the unit. Please
refer to the nameplate before selecting the
cable, fuse and switch.
19
6.4 Installation for the first time
5) Operate the vacuum pump to evacuate.
6) Make evacuation for 30 minutes and check
whether the compound meter indicates
-0.1Mpa(14.5Psi). If the meter does not
indicate -0.1Mpa(14.5Psi) after pumping 30
minutes, it should be pumped 20 minutes
more. If the pressure can’t achieve
-0.1Mpa(14.5Psi) after pumping 50 minutes,
please check if there are some leakage
points. Fully close the handle Lo valve of the
manifold valve and stop the operation of the
vacuum pump. Confirm that the gauge
needle does not move (approximately 5
minutes after turning off the vacuum pump).
7) Turn the flare nut of the 3-way valves about
45° counterclockwise for 6 or 7seconds
after the gas coming out, then tighten the
flare nut again. Make sure the pressure
display in the pressure indicator is a little
higher than the atmosphere pressure. Then
remove the charge hose from the 3 way
valve.
8) Fully open the 2 way valve and 3 way valve
and securely tighten the cap of the 3 way
valve.
Air and moisture in the refrigerant system have
undesirable effects as below:
●
●
●
●
Pressure in the system rises.
Operating current rises.
Cooling or heating efficiency drops.
Moisture in the refrigerant circuit may
freeze and block capillary tubing.
● Water may lead to corrosion of parts in the
refrigerant system.
Therefore, the indoor units and the pipes
between indoor and outdoor units must be leak
tested and evacuated to remove gas and
moisture from the system.
Gas leak check (Soap water method):
Apply soap water or a liquid neutral
detergent on the indoor unit connections or
outdoor unit connections by a soft brush to
check for leakage of the connecting points of
the piping. If bubbles come out, the pipes have
leakage.
1. Air purging with vacuum pump
2. Air purging by refrigerant
Procedure:
1). Confirm that both the 2-way and 3-way
valves are set to the closed position.
2). Connect the charge set and a charging
cylinder to the service port of the 3-way valve.
3). Air purging.
Open the valves on the charging cylinder and
the charge set. Purge the air by loosening the
flare nut on the 2-way valve approximately 45’
for 3 seconds then closing it for 1 minute; repeat
3 times.
1) Completely tighten the flare nuts of the
indoor and outdoor units, confirm that both
the 2-way and 3-way valves are set to the
closed position.
2) Connect the charge hose with the push pin
of handle lo to the 3-way valves gas service
port..
3) Connect the charge hose of handle hi
connection to the vacuum pump.
4) Fully open the handle Lo of the manifold
valve.
20
3) Put the charging cylinder onto the electronic
scale and record the weight.
4) Operate the air conditioner at the cooling
mode.
5) Open the valves (Low side) on the charge set
and charge the system with liquid refrigerant.
6).When the electronic scale displays the
proper weight (refer to the gauge and the
pressure of the low side), disconnect the charge
hose from the 3-way valve’s service port
immediately and turn off the air conditioner
before disconnecting the hose.
7). Mount the valve stem caps and the service
port
Use torque wrench to tighten the service port
cap to a torque of 18N.m.
Be sure to check for gas leakage.
After purging the air, use a torque wrench to
tighten the flare nut on the 2-way valve.
4). Check the gas leakage.
Check the flare connections for gas leakage.
5). Discharge the refrigerant.
Close the valve on the charging cylinder and
discharge the refrigerant by loosening the flare
nut on the 2-way valve approximately 45’ until
the gauge indicates 0.3Mpa(43.5Psi) to 0.5
Mpa(72.5Psi).
6). Disconnect the charge set and the charging
cylinder, and set the 2-way and 3-way valves to
the open position.
Be sure to use a hexagonal wrench to operate
the valve stems.
7). Mount the valve stems nuts and the service
port cap.
Be sure to use a torque wrench to tighten the
service port cap to a torque 18N·m.
Be sure to check the gas leakage.
6.6 Re-installation while the indoor unit
need to be repaired
1. Collecting the refrigerant into the outdoor
unit
6.5 Adding the refrigerant after running
the system for many years
Procedure
1). Confirm that both the 2-way and 3-way
valves are set to the opened position
Remove the valve stem caps and confirm that
the valve stems are in the opened position.
Be sure to use a hexagonal wrench to operate
the valve stems.
2). Connect the charge hose with the push pin
of handle lo to the 3-way valves gas service
port.
3). Air purging of the charge hose.
Open the handle Lo valve of the manifold valve
slightly to purge air from the charge hose for 5
seconds and then close it quickly.
Procedure
1). Connect the charge hose to the 3-way
service port, open the 2-way valve and the
3-way valve.
Connect the charge hose to the valve at the
bottom of the cylinder. If the refrigerant is
R410A, make the cylinder bottom up to ensure
liquid charge.
2). Purge the air from the charge hose.
Open the valve at the bottom of the cylinder
and press the check valve on the charge set to
purge the air (be careful of the liquid
refrigerant).
21
6). Disconnect the charge set and the charging
cylinder, and set the 2-way and 3-way valves to
the open position
Be sure to use a hexagonal wrench to operate
the valve stems.
7). Mount the valve stems nuts and the service
port cap
Be sure to use a torque wrench to tighten the
service port cap to a torque 18N.m.
Be sure to check the gas leakage.
4). Set the 2-way valve to the close position.
5). Operate the air conditioner at the cooling
cycle and stop it when the gauge indicates
0.1Mpa(14.5Psi).
6). Set the 3-way valve to the closed position
immediately
Do this quickly so that the gauge ends up
indicating 0.3Mpa(43.5Psi) to 0.5 Mpa(72.5Psi).
Disconnect the charge set, and tighten the
2-way and 3-way valve’s stem nuts.
Use a torque wrench to tighten the 3-way valves
service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
2. Air purging by the refrigerant
6.7 Re-installation while the outdoor
unit need to be repaired
1. Evacuation for the whole system
Procedure:
1). Confirm that both the 2-way and 3-way
valves are set to the opened position.
2). Connect the vacuum pump to 3-way valve’s
service port.
3). Evacuation for approximately one hour.
Confirm that the compound meter indicates
-0.1Mpa(14.5Psi).
4). Close the valve (Low side) on the charge set,
turn off the vacuum pump, and confirm that the
gauge needle does not move (approximately 5
minutes after turning off the vacuum pump).
5). Disconnect the charge hose from the
vacuum pump.
Procedure:
1). Confirm that both the 2-way and 3-way
valves are set to the closed position.
2). Connect the charge set and a charging
cylinder to the service port of the 3-way valve
Leave the valve on the charging cylinder closed.
3). Air purging.
Open the valves on the charging cylinder and
the charge set. Purge the air by loosening the
flare nut on the 2-way valve approximately 45’
for 3 seconds then closing it for 1 minute; repeat
3 times.
After purging the air, use a torque wrench to
tighten the flare nut on the 2-way valve.
4). Check the gas leakage
Check the flare connections for gas leakage.
5). Discharge the refrigerant.
Close the valve on the charging cylinder and
discharge the refrigerant by loosening the flare
nut on the 2-way valve approximately 45’ until
the gauge indicates 0.3Mpa(43.5Psi) to 0.5
Mpa(72.5Psi).
22
to check for gas leakage.
2. Refrigerant charging
Procedure:
1). Connect the charge hose to the charging
cylinder, open the 2-way valve and the 3-way
valve
Connect the charge hose which you
disconnected from the vacuum pump to the
valve at the bottom of the cylinder. If the
refrigerant is R410A, make the cylinder bottom
up to ensure liquid charge.
2). Purge the air from the charge hose
Open the valve at the bottom of the cylinder
and press the check valve on the charge set to
purge the air (be careful of the liquid
refrigerant).
3) Put the charging cylinder onto the electronic
scale and record the weight.
4). Open the valves (Low side) on the charge
set and charge the system with liquid refrigerant
If the system cannot be charge with the
specified amount of refrigerant, or can be
charged with a little at a time (approximately
150g each time) , operating the air conditioner
in the cooling cycle; however, one time is not
sufficient, wait approximately 1 minute and then
repeat the procedure.
5).When the electronic scale displays the
proper weight, disconnect the charge hose from
the 3-way valve’s service port immediately
If the system has been charged with liquid
refrigerant while operating the air conditioner,
turn off the air conditioner before disconnecting
the hose.
6). Mounted the valve stem caps and the
service port. Use torque wrench to tighten the
service port cap to a torque of 18N.m. Be sure
23
7. Operation Characteristics
Temperature
Mode
Room temperature
Cooling operation
Heating operation
Drying operation
≥17°C
≤30°C
>10°C
(62°F)
(86°F)
(50°F)
-15°C~50°C
-15°C~30°C
0°C~50°C
(5°F~122°F)
(5°F~86°F)
(32°F~122°F)
0°C~50°C
(32°F~122°F)
Outdoor temperature
(For the models with
low temperature cooling system)
CAUTION:
9ΔT(℃)
ΔT(℉) =
5
1. If the air conditioner is used beyond the above conditions, certain safety protection features may
come into operation and cause the unit to operate abnormally.
2. The room relative humidity should be less than 80%. If the air conditioner operates beyond this
figure, the surface of the air conditioner may attract condensation. Please set the vertical air flow louver to
its maximum angle (vertically to the floor), and set HIGH fan mode.
3. The optimum performance will be achieved during this operating temperature zone.
24
8. Electronic Function
8.1 Abbreviation
T1:
T2:
T3:
T4:
T5:
Indoor room temperature
Coil temperature of evaporator
Coil temperature of condenser
Outdoor ambient temperature
Compressor discharge temperature
8.2 Display function
8.2.1 Icon explanation on indoor display board.
ION indication lamp(optional function):This lamp illuminates when Clean Air
feature is activated.
DEFROST indication lamp(For cooling & heating models only): Lights up
when the air conditioner
starts
defrosting automatically or
when the warm air
control feature is activated in heating operation.
OPERATION indication lamp:This lamp illuminates when the air conditioner is in
operation.
TIMER indication lamp:Lights up during Timer operation.
Temperature indicator:Displays the temperature settings when the air conditioner
is operational. Displays the malfunction code.
25
8.3 Main Protection
8.3.1 Three minutes delay at restart for compressor
1 minute delay for the 1st time stand-up and 3 minutes delay for others.
8.3.2 Temperature protection of compressor top
The unit will stop working when the compressor top temp. protector cut off, and will restart after the
compressor top temp. protector restart.
8.3.3 Temperature protection of compressor discharge
When the compressor discharge temp. is getting higher, the running frequency will be limited as below
rules:
---Compressor discharge temp. T5>115°C(239°F) for 5s, compressor stops.
---108°C (226°F)<T5<115°C(239°F), decrease the frequency to the lower level every 3 minutes.
---90°C(194°F)<T5<105°C(221°F), keep running at the current frequency.
----T5<90°C(194°F), no limit for frequency.
8.3.4 Fan speed is out of control
When Indoor fan speed keeps too low (300RPM) for certain time, the unit will stop and the LED will
display the failure
8.3.5 Inverter module protection
The Inverter module has a protection function about current, voltage and temperature. If these
protections happen, the corresponding code will display on indoor unit and the unit will stop working.
8.3.6 Indoor fan delayed open function
When the unit starts up, the louver will be active immediately and the indoor fan will open 10s later.
If the unit runs in heating mode, the indoor fan will be also controlled by anti-cold wind function.
8.3.7 Compressor preheating functions
Preheating permitting condition:
If T4(outdoor ambient temperature)<3°C(37.4°F) and the machine connects to power supply newly or
if T4<3°C(37.4°F) and compressor has stopped for over 3 hours, the compressor heating cable will
work.
Preheating mode:
A weak current flow through the coil of compressor from the wiring terminal of the compressor, then the
compressor is heated without operation.
Preheating release condition:
If T4>5°C(41°F) or the compressor starts running, the preheating function will stop.
8.3.8 Zero crossing detection error protection
If AC detects time interval is not correct for continuous 240s, the unit will stop and the LED will display
the failure. The correct zero crossing signal time interval should be between 6-13ms.
8.3.9 Condenser temperature protection
---55°C(131°F)<T3<60°C(140°F), the compressor frequency will decrease to the lower level until to F1
and then runs at F1.If T3<54°C(129.2°F), the compressor will keep running at the current frequency.
---T3<52°C(125.6°F), the compressor will not limit the frequency and resume to the former frequency.
---T3>60°C(140°F) for 5 seconds, the compressor will stop until T3<52°C(125.6°F).
8.3.10 Evaporator temperature protection
---T2<0°C(32°F), the compressor will stop and restart when T2≧5°C(41°F).
---0°C(32°F)≦T2<4°C(39.2°F), the compressor frequency will be limited and decreased to the lower
level
---4°C(39.2°F)≤T2≤7°C(44.6°F), the compressor will keep the current frequency.
26
---T2>7°C(44.6°F), the compressor frequency will not be limited.
27
8.4 Operation Modes and Functions
T4
8.4.1 Fan mode
(1) Outdoor fan and compressor stop.
(2) Temperature setting function is disabled,
and no setting temperature is displayed.
(3) Indoor fan can be set to
high/med/low/auto.
(4) The louver operates same as in cooling
mode.
(5) Auto fan:
For MS11M-09HRFN1-MW0W,
MS11M-12HRFN1-MV0W,
MS11M-18HRFN1-MU0W models:
Fmax=F4
45¡ã
C(113¡ã
F)
43¡ã
C(109.4¡ã
F)
Fmax=F7
40¡ã
C(104¡ã
F)
38¡ã
C(100.4¡ã
F)
Fmax=F8
31.5¡ã
C(88.7¡ã
F)
29.5¡ã
C(85.1¡ã
F)
Fmax=F6
22.0¡ã
C(71.6¡ã
F)
20.0¡ã
C(68.0¡ã
F)
T1-24¡ã
C(75.2¡ã
F)
Fmax=F3
H
6.0¡ã
C(42.8¡ã
F)
5.0¡ã
C(41.0¡ã
F)
a
4.0¡ã
C(39.2¡ã
F)
b
2.5¡ã
C(36.5¡ã
F)
1.0¡ã
C(33.8¡ã
F)
c
d
e
Fmax: The maximum operation frequency of
compressor.
F1~F8: The detailed value of the compressor
operation frequency.
If users switch on AC by remote controller, the
compressor will run at the Fmax frequency for 7
minutes according to the outdoor ambient temp.
During the 7 minutes, the frequency limitation is
active. 7 minutes later, the compressor running
frequency will be controlled as below:
(H-L)*0.75+L
(H-L)*0.5+L
(H-L)*0.25+L
L
For MS11M-24HRDN1-MT0W model:
T1
27.5¡ã
C(81.5¡ã
F)
T1-Ts
High
3.5¡ã
C(38.3¡ã
F)
27.0¡ã
C(80.6¡ã
F)
25.5¡ã
C(77.9¡ã
F)
A
3.0¡ã
C(37.4¡ã
F)
Medium
2.5¡ã
C(36.5¡ã
F)
25.0¡ã
C(77.0¡ã
F)
2.0¡ã
C(35.6¡ã
F)
Low
1.5¡ã
C(34.7¡ã
F)
1.0¡ã
C(33.8¡ã
F)
0.5¡ã
C(32.9¡ã
F)
8.4.2 Cooling Mode
8.4.2.1 Compressor running rules
The maximum operation frequency of
compressor after starting submits to following
rule.
B
C
D
E
F
-0.5¡ã
C(31.1¡ã
F)
G
-1.0¡ã
C(30.2¡ã
F)
H
While the zones of A,B,C... are corresponding
to different compressor running frequency.
Note:
28
When T1-Ts keeps in the same temp. zone for
3 minutes, the compressor will run as the below
rules:
A~E: Increase the frequency to the higher level
until to F8.
F: Keep the current frequency.
G: Decrease the frequency to the lower level
until to F1.
H: Run at F1 for 1h.(if T1-Ts<-2°C(28.4°F), the
compressor will stop)
Meanwhile, the compressor running frequency
is limited by the current.
T4
28¡ã
C(82.4¡ã
F)
H
26¡ã
C(78.8¡ã
F)
20¡ã
C(68.0¡ã
F)
L
8.4.2.3 Indoor fan running rules
In cooling mode, indoor fan runs all the time
and the speed can be selected as high,
medium, low, auto and silent mode. When the
compressor is running, the indoor fan is
controlled as below:
Off
I3COOL
M
22¡ã
C(71.6¡ã
F)
Decrease
For MS11M-09HRFN1-MW0W,
MS11M-12HRFN1-MV0W,
MS11M-18HRFN1-MU0W models:
I2COOL
Hold
I1COOL
Resume
I3COOL, I2COOL,I1COOL mean different
running current value.
Off: Compressor stops.
Decrease: Decrease the running frequency to
the lower level.
Hold: Keep the current frequency.
Resume: No limitation for frequency.
Note:
When AC is in “hold” zone for 3 minutes, the
compressor frequency will rise to the higher
level.(frequency will increase twice at most)
8.4.2.2 Outdoor fan running rules
Auto fan running rules:
For MS11M-09HRFN1-MW0W,
MS11M-12HRFN1-MV0W,
MS11M-18HRFN1-MU0W models:
T1-Ts
6.0¡ã
C(42.8¡ã
F)
5.0¡ã
C(41.0¡ã
F)
4.0¡ã
C(39.2¡ã
F)
2.5¡ã
C(36.5¡ã
F)
1.0¡ã
C(33.8¡ã
F)
29
H
a
b
c
d
e
(H-L)*0.75+L
(H-L)*0.5+L
(H-L)*0.25+L
L
For MS11M-24HRDN1-MT0W model:
T1-Ts-¦ ¤T
T1-Ts
H
5.0¡ã
C(41¡ã
F)
4.5¡ã
C(40.1¡ã
F)
High
3¡ã
C(37.4¡ã
F)
1.5¡ã
C(34.7¡ã
F)
Medium
F
2.5¡ã
C(36.5¡ã
F)
E
D
C
1.5¡ã
C(34.7¡ã
F)
B
1.0¡ã
C(33.8¡ã
F)
Low
0.5¡ã
C(32.9¡ã
F)
T4
Off
Fmax=F2
25¡ã
C(77.0¡ã
F)
24¡ã
C(75.2¡ã
F)
Fmax=F3
22¡ã
C(71.6¡ã
F)
21¡ã
C(69.8¡ã
F)
Fmax=F4
19¡ã
C(66.2¡ã
F)
18¡ã
C(64.4¡ã
F)
Fmax=F5
17¡ã
C(62.6¡ã
F)
16¡ã
C(60.8¡ã
F)
Fmax=F6
15¡ã
C(59.0¡ã
F)
14¡ã
C(57.2¡ã
F)
Fmax=F7
12¡ã
C(53.6¡ã
F)
11¡ã
C(51.8¡ã
F)
Fmax=F8
6.0¡ã
C(42.8¡ã
F)
5.0¡ã
C(41.0¡ã
F)
Fmax=F9
A
While the zones of A,B,C... are corresponding
to different compressor running frequency.
ΔT=0°C(32°F) as default.
Note:
When T1-Ts keeps in the same temp. zone for
3 minutes, the compressor will run as the below
rules:
A~E: Increase the frequency to the higher level
until to F10.
F: Keep the current frequency.
G: Decrease the frequency to the lower level
until to F1.
H: Run at F1 for 1h.(if T1-Ts-ΔT >6°C(42.8°F),
the compressor will stop)
Meanwhile, the compressor running frequency
is limited by the current.
8.4.3 Heating Mode
8.4.3.1 Compressor running rules
The maximum operation frequency of the
compressor after starting submits to the
following rule.
28¡ã
C(82.4¡ã
F)
27¡ã
C(80.6¡ã
F)
3.0¡ã
C(37.4¡ã
F)
2.0¡ã
C(35.6¡ã
F)
1.0¡ã
C(33.8¡ã
F)
34¡ã
C(93.2¡ã
F)
33¡ã
C(91.4¡ã
F)
G
3.5¡ã
C(38.3¡ã
F)
4¡ã
C(39.2¡ã
F)
Off
I3HEAT
Decrease
Fmax=F10
I2HEAT
Fmax: The maximum operation frequency of
compressor.
F1~F8: The detailed value of the compressor
operation frequency.
If users switch on AC by remote controller, the
compressor will run at the Fmax frequency for 7
minutes according to outdoor ambient temp.
During the 7 minutes, the frequency limitation is
active.
7 minutes later, the compressor running
frequency will be controlled as below:
Hold
I1HEAT
Resume
I3HEAT, I2HEAT,I1HEAT mean different
running current value.
Off: Compressor stops.
Decrease: Decrease the running frequency to
the lower level.
Hold: Keep the current frequency.
30
Resume: No limitation for frequency.
Note:
When AC is in “hold” zone for 3 minutes, the
compressor frequency will rise to the higher
level. (The frequency will increase twice at
most)
8.4.3.2 Outdoor fan running rules
T2
¡ã
C
Setting
TEL8
TEL7
TEL6
Medium
TEL5
TEL4
Low
T4
TEL3
TEL2
Breeze
TEL1
17¡ã
C(62.6¡ã
F)
Super
Breeze
L
TEL0
Off
15¡ã
C(59.0¡ã
F)
For MS11M-24HRDN1-MT0W model:
M
12¡ã
C(53.6¡ã
F)
T2¡ãC
10¡ã
C(50.0¡ã
F)
H
TEL8
Setting
TEL7
TEL6
8.4.3.3 Indoor fan running rules
Indoor fan speed can be set as high, medium,
low, silent mode or auto grade. During all the
fan speeds, the anti-cold-wind function is
preferential. If the compressor stops caused by
the room temperature rising, the indoor fan will
run at super breeze. When the compressor is
running, the indoor fan is controlled as below:
Medium
TEL5
TEL4
Low
TEL3
TEL2
Breeze
TEL0
Off
Auto fan action in heating mode.
For MS11M-09HRFN1-MW0W,
MS11M-12HRFN1-MV0W,
MS11M-18HRFN1-MU0W models:
T1-Ts+¦ ¤
T
0.0¡ã
C(32¡ã
F)
L
-1¡ã
C(30.2¡ã
F)
-2¡ã
C(28.4¡ã
F)
(H+-L)*0.2+L
(H+-L)*0.4+L
-3¡ã
C(26.6¡ã
F)
(H+-L)*0.6+L
-4¡ã
C(24.8¡ã
F)
-5¡ã
C(23.0¡ã
F)
-6¡ã
C(21.2¡ã
F)
-6.5¡ã
C(20.3¡ã
F)
The anti-cold wind function is as below:
For MS11M-09HRFN1-MW0W,
MS11M-12HRFN1-MV0W,
MS11M-18HRFN1-MU0W models:
31
(H+-L)*0.8+L
H+
For 9k,12k models:
For MS11M-24HRDN1-MT0W model:
T1-Ts
Frequency F2 FrequencyF8
on
Compressor
Low
2.5¡ã
C(36.5¡ã
F)
4-way valve
2.0¡ã
C(35.6¡ã
F)
Outdoor fan
Medium
1.5¡ã
C(34.7¡ã
F)
Indoor fan
1.0¡ã
C(33.8¡ã
F)
off
on
off
on
off
on
off
High
Indoor fan breeze(10s)
10s
xx
10s
8.4.3.4 Defrosting mode
Condition of defrosting:
----T4>0°C(32°F),
When the units are running, if the following two
items are satisfied, the units start defrosting:
The units run with T3<3°C(37.4°F), for 40
minutes and T3 keeps lower than TCDI°C for
more than 3 minutes.
The units run with T3<3°C(37.4°F) for 80
minutes and T3 keeps lower than
TCDI+2°C(35.6°F) for more than 3 minutes.
----T4<0°C(32°F),
If the 1st condition and 2nd condition items are
satisfied, then the program judges if T2 has
decreased more than 5°C(41°F).When T2 has
decreased more than 5°C(41°F), enter the
defrosting mode.
----No matter what value T4 is, if the machine
runs with T3<3°C(37.4°F) for more than 120
minutes and T3 keeps lower than
TCDI+4°C(39.2°F) for more than 3 minutes, the
machine will enter defrosting mode no matter if
T2 drops more than 5°C(41°F) or not.
Condition of ending defrosting:
If any one of the following items is satisfied, the
defrosting will finish and the machine will turn to
normal heating mode.
----T3 rises to be higher than TCDE1°C.
----T3 keeps to be higher than TCDE2°C for 80
seconds.
----The machine has run for 10 minutes in
defrosting mode.
Defrosting action:
no longer than 10m
30s
xx=60s.
For 18k,24k models:
Frequency F2 Frequency F8
on
Compressor
4-way valve
Outdoor fan
Indoor fan
off
on
off
on
off
on
off
Indoor fan breeze(10s)
10s
xx
10s
no longer than 10m
30s
XX=90.
8.4.3.5 Evaporator coil temperature
protection
----T2> TEH2 °C, the compressor running
frequency decreases to the lower level and
runs for 20s.
When the frequency decreases to F2 and the
T2 is still over TEH2 °C for 3 minutes, the
compressor will stop.
----T2<48°C(118.4°F) or T2 stays in
48°C(118.4°F)~TEH2 °C for 6 minutes, the
32
not resume until room temperature exceeds
12°C(53.6°F).
8.4.5.4 Evaporator anti-freezing protection,
condenser high temperature protection and
outdoor unit frequency limit are active and the
same as that in cooling mode.
8.4.5.5 The outdoor fan operates the same as
in cooling mode.
8.4.6 Forced operation function
8.4.6.1 Enter forced operation function:
When the machine is off, pressing the touch
button will carry the machine to forced auto
mode. If pressing the button once again within
5 seconds, the machine will turn into forced
cooling mode.
In forced auto, forced cooling or any other
operation mode, pressing touch button will turn
off the machine.
8.4.6.2 In forced operation mode, all general
protections and remote control are available.
8.4.6.3 Operation rules:
Forced cooling mode:
The compressor runs at F2 frequency and
indoor fan runs as breeze. After running for 30
minutes. the machine will turn to auto mode as
24°C(75.2°F) setting temperature.
Forced auto mode:
The action of forced auto mode is the same as
normal auto mode with 24°C(75.2°F) setting
temperature.
8.4.7 Timer function
8.4.7.1 Timing range is 24 hours.
8.4.7.2 Timer on. The machine will turn on
automatically when reaching the setting time.
8.4.7.3 Timer off. The machine will turn off
automatically when reaching the setting time.
8.4.7.4 Timer on/off. The machine will turn on
automatically when reaching the setting “on”
time, and then turn off automatically when
reaching the setting “off” time.
8.4.7.5 Timer off/on. The machine will turn off
automatically when reaching the setting “off”
time, and then turn on automatically when
reaching the setting “on” time.
8.4.7.6 The timer function will not change the
AC current operation mode. Suppose AC is off
frequency will not be limited by T2.
----T2>60°C(140°F), the compressor will stop
and restart when T2<48°C(118.4°F).
8.4.4 Auto-mode
This mode can be chosen with remote
controller and the setting temperature can be
changed between 17°C(62.6°F)~30°C(86°F).
In auto mode, the machine will choose cooling,
heating or fan-only mode according to ΔT
(ΔT =T1-Ts).
ΔT=T1-Ts
Running mode
ΔT>1°C(33.8°F)
Cooling
-1°C(30.2°F)<ΔT≤1°C(33.8°F)
Fan-only
ΔT≤-1°C(30.2°F)
Heating
Indoor fan will run at auto fan of the relevant
mode.
The louver operates same as in relevant mode.
If the machine switches mode between heating
and cooling, the compressor will keep stopping
for 15 minutes and then choose mode
according to T1-Ts.
If the setting temperature is modified, the
machine will choose running function again.
8.4.5 Drying mode
8.4.5.1 Indoor fan speed is fixed at breeze and
can’t be changed. The louver angle is the same
as in cooling mode.
8.4.5.2 Compressor running rules
T1-Ts
2.5¡ã
C(36.5¡ã
F)
F3
2.0¡ã
C(35.6¡ã
F)
1.5¡ã
C(34.7¡ã
F)
F2
1.0¡ã
C(33.8¡ã
F)
0.5¡ã
C(32.9¡ã
F)
F1
0.0¡ã
C(32.0¡ã
F)
F1
8.4.5.3 Low indoor room temperature protection
In drying mode, if room temperature is lower
than 10°C(50°F), the compressor will stop and
33
the compressor will have 3 minutes delay when
restarts.
8.4.10 Follow me
1) If the indoor PCB receives the signal which
results from pressing the FOLLOW ME button
on remote controller, the buzzer will emit a
sound and this indicates the follow me function
is initiated. But when the indoor PCB receives
signal which sent from remote controller every
3 minutes, the buzzer will not respond. When
the unit is running with follow me function, the
PCB will control the unit according to the
temperature from follow me signal, and the
temperature collection function of room
temperature sensor will be shielded, but the
error detective function of room temperature
sensor will be still valid.
2) When the follow me function is available,
the PCB will control the unit according to the
room temperature from the remote controller
and the setting temperature.
3) The PCB will take action to the mode
change information from remote controller
signal, but it will not affected by the setting
temperature.
4) When the unit is running with follow me
function, if the PCB doesn’t receive any signal
from remote controller for 7 minutes or pressing
FOLLOW ME button again, the follow me
function will be turned off automatically, and the
temperature will control the unit according to
the room temperature detected from its own
room temperature sensor and setting
temperature.
8.4.11 Self clean
For heat pump models which are provided with
this function, after running in cooling or drying
mode, if the user press “Self Clean” button on
remote controller, firstly, indoor unit runs in fan
only mode for a while, then low heat operation
and finally runs in fan only again. This function
can keep the inside of indoor unit dry and
prevent breeding of mold.
now, it will not start up firstly after setting the
“timer off” function. And when reaching the
setting time, the timer LED will be off and the
AC running mode has not been changed.
8.4.7.7 The setting time is relative time.
8.4.8 Sleep function mode
8.4.8.1 Operation time in sleep mode is 7 hours.
After 7 hours the AC quits this mode and turns
off.
8.4.8.2. Operation process in sleep mode is as
follow:
When cooling, the setting temperature rises
1°C(33.8°F) (be lower than 30°C(86°F)) every
one hour, 2 hours later the setting temperature
stops rising and indoor fan is fixed as low
speed.
When heating, the setting temperature
decreases 1°C(33.8°F) (be higher than
17°C(62.6°F)) every one hour, 2 hours later the
setting temperature stops rising and indoor fan
is fixed as low speed. (Anti-cold wind function
has the priority)
8.4.8.3 Timer setting is available
8.4.8.4 When user uses timer off function in
sleep mode (or sleep function in timer off mode),
if the timing is less than 7 hours, sleep function
will be cancelled when reaching the setting time.
If the timing is more than 7 hours, the machine
will not stop until reaches the setting time in
sleep mode.
8.4.9 Auto-Restart function
The indoor unit is equipped with auto-restart
function, which is carried out through an
auto-restart module. In case of a sudden power
failure, the module memorizes the setting
conditions before the power failure. The unit will
resume the previous operation setting (not
including swing function) automatically after 3
minutes when power returns.
If the memorization condition is forced cooling
mode, the unit will run in cooling mode for 30
minutes and turn to auto mode as 24°C(75.2°F)
setting temp.
If AC is off before power off and AC is required
to start up now, the compressor will have 1
minute delay when power on. Other conditions,
8.4.12 Refrigerant Leakage Detection
With this new technology, the display area will
34
the air conditioner can be as lower as 8°C,
which keeps the room temperature steady at
8°C and prevents household things freezing
when the house is unoccupied for a long time in
severe cold weather.
8.4.15 Silence operation(optional)
Press the “silence” button on remote controller
to initiate SILENCE function. When the Silence
function is activated, the compressor running
frequency will keep lower than F2 and the
indoor unit will bring faint breeze, which will
reduce the noise to the lowest level and create
a quiet and comfortable room for you.
show “EC” when the outdoor unit detects
refrigerant leakage.
8.4.13 Louver Position Memory Function
When starting the unit again after shutting down,
its louver will restore to the angle originally set
by the user, but the precondition is that the
angle must be within the allowable range, if it
exceeds, it will memorize the maximum angle
of the louver. During operation, if the power fails
or the end user shuts down the unit in the turbo
mode, the louver will restore to the default
angle.
8.4.14 8°C Heating(optional)
In heating operation, the preset temperature of
35
9. Troubleshooting
Safety
Electricity power is still kept in capacitors even the power supply is shut off. Do not forget to discharge the electricity
power in capacitor.
Electrolytic Capacitors
(HIGH VOLTAGE! CAUTION!)
For other models, please connect discharge resistance (approx.100Ω 40W) or soldering iron (plug) between +, terminals of the electrolytic capacitor on the contrary side of the outdoor PCB.
Note: The picture above is only for reference. The plug of your side may be different.
36
9.1 Indoor Unit Error Display
Operation
lamp
Timer lamp
Display
☆ 1 time
X
E0
Indoor unit EEPROM parameter error
☆ 2 times
X
E1
Indoor / outdoor units communication error
☆ 3 times
X
E2
Zero-crossing signal detection error
☆ 4 times
X
E3
Indoor fan speed has been out of control
☆ 5 times
X
E4
Indoor room temperature sensor T1 open circuit or short
circuit
☆ 6 times
X
E5
Evaporator coil temperature sensor T2 open circuit or
short circuit
☆ 7 times
X
EC
Refrigerant leakage detection
☆ 2 times
O
F1
Outdoor ambient temperature sensor T4 open circuit or
short circuit
☆ 3 times
O
F2
Condenser coil temperature sensor T3 open circuit or
short circuit
☆ 4 times
O
F3
Compressor discharge temperature sensor T5 open
circuit or short circuit
☆ 5 times
O
F4
Outdoor unit EEPROM parameter error
☆ 6 times
O
F5
Outdoor fan speed has been out of control
☆ 1 times
☆
P0
IPM malfunction or IGBT over-strong current protection
☆ 2 times
☆
P1
Over voltage or over low voltage protection
☆ 3 times
☆
P2
High temperature protection of compressor top
diagnosis and solution(only for 9k,12k models)
☆ 5 times
☆
P4
Inverter compressor drive error
O(light)
LED STATUS
X(off)
37
☆(flash)
9.2 Outdoor unit error display

MOC-09HFN1-MW0W and MOC-12HFN1-MV0W:
After power on, LED100(Blue color) will be slow flash(0.2Hz) when the unit is in standby and
quick flash (2.5Hz) if the unit has some problems.
No.
Problems
LED301
(Green)
LED300
(Red)
1
standby for normal
O
X
2
Operation normally
X
O
3
IPM malfunction or IGBT over-strong current protection
☆
X
P0
4
Over voltage or too low voltage protection
O
O
P1
5
Over voltage or too low voltage protection
O
☆
P1
6
Inverter compressor drive error
X
☆
P4
7
Inverter compressor drive error
☆
O
P4
8
Inverter compressor drive error
☆
☆
P4
O(light)
X(off)
38
☆(2.5Hz flash)
IU display

MOF-18HFN1-MU0W
+
E3
CN31
+
T3.15AL/250VAC
FUSE1
E5
E4
CN32
+
202302130651
E2
C64
CN13
CN27
D1
BR1
C6
R208
RY4
R30
RY3
HEAT-L
+
CN34
R41
CN6
RED
CN28
CN36
CN7
YELLOW
CN9
HEAT-N
CN8
BLUE
C11
R38
C18
DZ1
BROWN
C214
R31
R217
IC10
IC8
C12
E206
D2
CN29
CN26
CN24
1
RY1
IC201
C4
+
4-WAY-N
C67
RED
CN25
R43
YELLOW
RY2
CN4
E14
D7
BLUE
C213
BR2
D208
15
R203
R204
T201
+
R215
IC5
R209
R206
IC203
R201
C35
D209
+
IC19
R74
LED4
R27
R28
C73
+
CN21
HuiQi
CN20
E24
PaiQi
CN16
TEMP
CN15
R102
R103
R106
R105
+17V
C48
C70
C54
R84
VSS
C57
R86
R88
R85
C32
C66
C65
C71
C59
C51
C50
C58
C55
C8
R66
R91
R11
R75
R78
LED2
+
PMV
C43
R73
+
D10
+
E11
CompTop
ISO
D11
+
+
C72
C44
+
R71
FAULT
IC12
LED1
C69
X1
R76
CN14
R104
R57
PCPort
R63
C39
CN12
R51
R62
R61
R54
C68
C38
W-
R72
+
E17
+
R60
R87
C40
17
+
E23
C37
R89
E28
33
IC17
C29
FUSE2
TestPort
C14
E25
R29
C30
R92
R93
C63
+
C9
C60
C52
R81 R83 R82
VR58
49
IC18
C31
C61
CN37
U-
C28
CN11
S
ZR1
W+
C27
C25
OSC1
IC13
R55 R95
IC7
1
C36
ZR3
U+
V+
CN22
R59
E18
R80
DAS1
L-IN
CN2
N
24LC256
C62
C53
R101
R35
R34
LED3
C56
R94
IC15
R53
R90
C47
IC16
C45
R46
D14
P
C46
R32
+
R49
C24
W
C33
R33
R79
R67
R69
R70
C42
R77
VB3
W
E15
R68
R50
R48
CN19
C21
IC3
C41 R64 R65
IC14
24LC04
R36
D204
D205
D201
C209
C201
R211
D206
C204
R212
R42
R39
C23
C17
C49
T20AL/250VAC
C34
E20
D15
Q3
C22
CN38
VB2
V
E13
E203
C203
VB1
U
+
R20
+
+
E201
IC9
C3
E21
V
+
+
+
R205
R40
R47
N-IN
CN1
CN18
IC6
C20 +
CN3
L1
IC11
D17
E16
R216
+
C2
E22
U
DZ2
+
PTC1
+
R213
CN17
C210
E207
R202
+
10
E202
D16
R52
D207
C202
R2
R214
8
R210
PTC2
11
7
C206
C208
R12
+
R45
C1
IPM1
12
IC202
D9
BROWN
6
R207
CN35
R1
C205
R56
R19
R9
C5
D203
R44
E204
T1
CN30
D202
Q2
Q1
ZR2
+
R37
C26
13
L-OUT
3
4-WAY-N
14
CN33
E19
R8
E8
CE-KFR26W/BP3N1(PMV)-120.D.13.WP2-1
E27
E26
R110
R109
R107
R108
LED2 LED2 on and LED1 off (standby)
LED2 off and LED1 on (running)
LED1
other status (error)
power light
LED4 when
power is on, LED4 aways on
LED3
Flashing once per second(low speed flashing) (standby)
Flashing once per half second (high speed flashing) (error)
aways on (running)
No.
Problems
LED2
(Green)
LED1
(Red)
1
standby for normal
O
X
2
Operation normally
X
O
3
IPM malfunction or IGBT over-strong current protection
☆
X
P0
4
Over voltage or too low voltage protection
O
O
P1
5
Over voltage or too low voltage protection
O
☆
P1
6
Inverter compressor drive error
X
☆
P4
7
Inverter compressor drive error
☆
O
P4
8
Inverter compressor drive error
☆
☆
P4
O(light)
X(off)
39
☆(2.5Hz flash)
IU display
MOG-24HFN1-MT0W
LED1
(standby) Flashing once per second(low speed flashing)
(error) Flashing once per half second (high speed flashing)
(running) aways on
B
A
CN24
CN22
CN19
CN18
E28
C83
+
C
17V
IC32
IC3
IC6
R111
C80
R112
R113
IC30
C64
C62
IC1
DZ1
E33
IC18
NR114
IC17
+
CN38
D
C63
C82
R31
R115
CN17 T3/T4
R38
+
E9
1
IC5
1
R91
R46 C32
R68
R66
R69
R70
CN23
S-B
CN25
S-A
D30
1
R49
C34
R47
IC10
D16
D33
C57
+
R10
R19
R13
R11
E12
C75
R58 C41
IC16
C44
R1
R3
CONdebug1
2
D32
1
IC8
R48
C37 R51
1
1
S-C
C36
CompTop
16
CN20
D14
R94
E1
LOW/HIGH
15
CN10
R36
IC7
C76
R90
R101
R50
R93
R92
C38
D1
R4
S
C18
C29
+
CT1
R40
D17
C70
C61
D20
S-D
CN16
D10
C27
C26
R42 C30
C60
R30 IC11
C35
CN12
R14
R9
CN14
R41
C12
R2
C47
R65
C22
C31
D6
+
C77
E13
R35 R37
R53
P+
IC4
C21
R21
C15
C1
C13
C14
C17
R15
1 R54
C28
R56
C78
R55
R96
R25
C39
R22
R82
R87
C9
R80
D31
+
R110
R109
R107
R57
D9
R78
R29
C19
C16
R33 C20
SW1
R76
N-
1
R52
C40
C23
R103
R24 R27
C72
C67
R108
PEQ
Q2
R73
R89
IC2
CN28
IC9
1
E14
C49
IC14
C43
R104
C79
CN39
+
X1
C74
R81
C56
D28
C58
R99
PFC-CONTROL
R95
C55
R60
D27
C81
DSP1
R86
R62
T2B
R71
LED1
R74
R79
E31
C53
CN27 R120
TestPort
D12
CN15
IC15
R88
Q4
CN26
C54
D11
C59
C69
D19
TO-DRIVE
R77
RUN
D8
R84
R83
C73
CN21
R102
C71
E7
R106
R105
E27
C65
R32
CN7 R5
R98
R117
L30
Q3
R100
+
R28
R26
+
+
E6
D7
1
1
R85
R97
1
C24
PAI QI
R23
R18
R20
R17 +
R16
E5
E4
C25
C68
D15
+
E10
D13
C66
+
E11
DC MOTOR
CN37
Q5
R116
R118
D5
E2
+
R34
E8
+
R39 R6
+

L-OUT
IC12
R64
R59
C42
C84
C45
R61
R67 C46
R72
R45
R75
R63
C33
D2
1
1
IC13
D18
D34
C51
1
P-2
GND
C85
R44
C10
CN1
D3
CN2
4-WAY
RY1
C11
N
FUSE1
CN6
RY2
CN5
HEAT1
RY3
N
CN8
R8
202302130895
L-IN
N
P2
CN3
FUSE2
N-OUT
HEAT2
R7
PTC1
CN29
P1
T5A 250VAC
CN9
D4
Q1
RY4
ZR1
CE-KFR80W/BP3T4N1(DC MOTOR)-310.D.03.WP1-1
C2
T30A 250VAC
C3
C48
AS1
P-1
GND
CN4
C52
C5
C6
C7
N-IN
L2
L1
40
C8
C4
ZR3
ZR2
9.3 Diagnosis and Solution
9.3.1 EEPROM parameter error diagnosis and solution(E0/F4)
Error Code
E0/F4
Malfunction decision
Indoor or outdoor PCB main chip does not receive feedback
conditions
from EEPROM chip.
Supposed causes
●
Installation mistake
●
PCB faulty
Trouble shooting:
EEPROM: a read-only memory whose contents can be erased and reprogrammed using a pulsed
voltage. For the location of EEPROM chip, please refer to the below photos.
Outdoor PCB(18k model)
Indoor PCB
Note: The two photos above are only for reference, it’s may be not same totally with the ones on
your side.
41
9.3.2 Indoor / outdoor unit’s communication diagnosis and solution(E1)
Error Code
E1
Malfunction decision
Indoor unit does not receive the feedback from outdoor unit during
conditions
110 seconds and this condition happens four times continuously.
Supposed causes
●
Wiring mistake
●
Indoor or outdoor PCB faulty
Trouble shooting:
42
Remark:
Use a multimeter to test the DC voltage
between L2 port and S port of outdoor
unit. The red pin of multimeter connects
with L2 port while the black pin is for S
port.
When AC is normal running, the voltage
will move alternately between -50V to
50V.
If the outdoor unit has malfunction, the
voltage will move alternately with positive
value.
While if the indoor unit has malfunction,
the voltage will be a certain value.
Remark:
Use a multimeter to test the resistance
of the reactor which does not connect
with capacitor.
The normal value should be around zero
ohm. Otherwise, the reactor must have
malfunction and need to be replaced.
43
9.3.3 Zero crossing detection error diagnosis and solution(E2)
Error Code
E2
Malfunction decision
When PCB does not receive zero crossing signal feedback for 4
conditions
minutes or the zero crossing signal time interval is abnormal.
Supposed causes
●
Connection mistake
●
PCB faulty
Trouble shooting:
44
9.3.4 Fan speed has been out of control diagnosis and solution(E3)
Error Code
E3
Malfunction decision
When indoor fan speed keeps too low (300RPM) for certain time,
conditions
the unit will stop and the LED will display the failure.
Supposed causes
●
Wiring mistake
●
Fan ass’y faulty
●
Fan motor faulty
●
PCB faulty
Trouble shooting:
45
Index 1:
1.Indoor or Outdoor DC Fan Motor(control chip is in fan motor)
Measure the resistance value of each winding by using the tester. If any resistance value is zero, the
fan motor must has problems and need to be replaced.
Index2:
1:Indoor or Outdoor DC Fan Motor(control chip is in fan motor)
Power on and when the unit is in standby, measure the voltage of pin1-pin3, pin4-pin3 in fan motor
connector. If the value of the voltage is not in the range showing in below table, the PCB must has
problems and need to be replaced.
DC motor voltage input and output
NO.
Color
Signal
Voltage
1
Red
Vs/Vm
280V~380V
2
---
---
---
3
Black
GND
0V
4
White
Vcc
14-17.5V
5
Yellow
Vsp
0~5.6V
6
Blue
FG
14-17.5V
46
2.Outdoor DC Fan Motor(control chip is in outdoor PCB)
NO.
1
2
3
4
5
Color
Orange
Grey
White
Pink
Black
Signal
Hu
Hv
Hw
Vcc
GND
Color
Red
Blue
Yellow
Signal
W
V
U
1) Release the UVW connector. Measure the resistance of U-V, U-W, V-W. If the resistance is not
equal to each other, the fan motor must has problems and need to be replaced. Otherwise, go to
step 2.
2) Power on and when the unit is in standby, measure the voltage of pin4-5 in feedback signal
connector. If the value is not 5V, change the PCB. Otherwise, go to step 3.
3) Rotate the fan by hand, measure the voltage of pin1-5, pin 2-5 and pin 3-5 in feedback signal
connector. If any voltage is not positive voltage fluctuation, the fan motor must has problems and
need to be replaced.
47
9.3.5 Open circuit or short circuit of temperature sensor diagnosis and solution(E5)
Error Code
E5
Malfunction decision
If the sampling voltage is lower than 0.06V or higher than 4.94V,
conditions
the LED will display the failure.
Supposed causes
●
Wiring mistake
●
Sensor faulty
Trouble shooting:
48
9.3.6 Refrigerant Leakage Detection diagnosis and solution(EC)
Error Code
EC
Malfunction decision
Define the evaporator coil temp.T2 of the compressor just starts
conditions
running as Tcool.
In the beginning 5 minutes after the compressor starts up, if T2
<Tcool-2°C(Tcool-35.6°F) does not
keep continuous 4
seconds and this situation happens 3 times, the display area will
show “EC” and AC will turn off.
Supposed causes
●
T2 sensor faulty
●
Indoor PCB faulty
●
System problems, such as leakage or blocking.
Trouble shooting:
49
9.3.7 IPM malfunction or IGBT over-strong current protection diagnosis and solution(P0)
Error Code
P0
Malfunction decision
When the voltage signal that IPM send to compressor drive chip
conditions
is abnormal, the display LED will show “P0” and AC will turn off.
Supposed causes
●
Wiring mistake
●
IPM malfunction
●
Outdoor fan ass’y faulty
●
Compressor malfunction
●
Outdoor PCB faulty
Trouble shooting:
50
Take the 9k model as example:
P-U
P-V
51
P-W
N-U
52
N-V
N-W
53
te
esoepace
outdoo
000epace
t
s
ot
te
easue
te
up
stat
e
aue
uts
o
ds
deet
o
o
o
ad
o
oesoesoe
sup
poe
e
u
te
oascoect
9.3.8 Over voltage or too low voltage protection diagnosis and solution(P1)
Error Code
P1
Malfunction decision
An abnormal voltage rise or drop is detected by checking the
conditions
specified voltage detection circuit.
Supposed causes
●
Power supply problems.
●
System leakage or block
●
PCB faulty
Trouble shooting:
Remark:
Measure the DC voltage
between P and N port. The
normal value should be
around 310V.
P
N
54
eso
outd
te
Ooepace
te
eoesepace
t
s
te
esotectooeasue
syste
ouegeat
egeat
co
te
ateoayoecage
utes
0
o
t
po
te
o
esoesesu
a
te
Cec
9.3.9 High temperature protection of compressor top diagnosis and solution(P2)
Error Code
P2
Malfunction decision
If the sampling voltage is not 5V, the LED will display the failure.
conditions
Supposed causes
●
Power supply problems.
●
System leakage or block
●
PCB faulty
Trouble shooting:
55
te
Cec
ad
C
a
outd
te
coesepace
te
oepace
page
to
ee
uo
ae
cotoesaues
o
out
gooesos
s
oetato
tegat
ae
C
te
C
a
te
epace
page
to
ee
es
tea
c
cotuty
coeeso
ad
es
cope
ad
C
9.3.10 Inverter compressor drive error diagnosis and solution(P4)
Error Code
P4
Malfunction decision
An abnormal inverter compressor drive is detected by a special
conditions
detection circuit, including communication signal detection,
voltage detection, compressor rotation speed signal detection
and so on.
Supposed causes
●
Wiring mistake
●
IPM malfunction
●
Outdoor fan ass’y faulty
●
Compressor malfunction
●
Outdoor PCB faulty
Trouble shooting:
56
Main parts check
1. Temperature sensor checking
Disconnect the temperature sensor from PCB, measure the resistance value with a tester.
Temperature sensors.
Room temp.(T1) sensor,
Indoor coil temp.(T2) sensor,
Outdoor coil temp.(T3) sensor,
Outdoor ambient temp.(T4) sensor,
Compressor discharge temp.(T5) sensor.
Measure the resistance value of each winding by using the multi-meter.
57
Appendix 1 Temperature Sensor Resistance Value Table for T1,T2,T3,T4 (°C--K)
°C
°F
K Ohm
°C
°F
K Ohm
°C
°F
K Ohm
°C
°F
K Ohm
-20
-4
115.266
20
68
12.6431
60
140
2.35774
100
212
0.62973
-19
-2
108.146
21
70
12.0561
61
142
2.27249
101
214
0.61148
-18
0
101.517
22
72
11.5
62
144
2.19073
102
216
0.59386
-17
1
96.3423
23
73
10.9731
63
145
2.11241
103
217
0.57683
-16
3
89.5865
24
75
10.4736
64
147
2.03732
104
219
0.56038
-15
5
84.219
25
77
10
65
149
1.96532
105
221
0.54448
-14
7
79.311
26
79
9.55074
66
151
1.89627
106
223
0.52912
-13
9
74.536
27
81
9.12445
67
153
1.83003
107
225
0.51426
-12
10
70.1698
28
82
8.71983
68
154
1.76647
108
226
0.49989
-11
12
66.0898
29
84
8.33566
69
156
1.70547
109
228
0.486
-10
14
62.2756
30
86
7.97078
70
158
1.64691
110
230
0.47256
-9
16
58.7079
31
88
7.62411
71
160
1.59068
111
232
0.45957
-8
18
56.3694
32
90
7.29464
72
162
1.53668
112
234
0.44699
-7
19
52.2438
33
91
6.98142
73
163
1.48481
113
235
0.43482
-6
21
49.3161
34
93
6.68355
74
165
1.43498
114
237
0.42304
-5
23
46.5725
35
95
6.40021
75
167
1.38703
115
239
0.41164
-4
25
44
36
97
6.13059
76
169
1.34105
116
241
0.4006
-3
27
41.5878
37
99
5.87359
77
171
1.29078
117
243
0.38991
-2
28
39.8239
38
100
5.62961
78
172
1.25423
118
244
0.37956
-1
30
37.1988
39
102
5.39689
79
174
1.2133
119
246
0.36954
0
32
35.2024
40
104
5.17519
80
176
1.17393
120
248
0.35982
1
34
33.3269
41
106
4.96392
81
178
1.13604
121
250
0.35042
2
36
31.5635
42
108
4.76253
82
180
1.09958
122
252
0.3413
3
37
29.9058
43
109
4.5705
83
181
1.06448
123
253
0.33246
4
39
28.3459
44
111
4.38736
84
183
1.03069
124
255
0.3239
5
41
26.8778
45
113
4.21263
85
185
0.99815
125
257
0.31559
6
43
25.4954
46
115
4.04589
86
187
0.96681
126
259
0.30754
7
45
24.1932
47
117
3.88673
87
189
0.93662
127
261
0.29974
8
46
22.5662
48
118
3.73476
88
190
0.90753
128
262
0.29216
9
48
21.8094
49
120
3.58962
89
192
0.8795
129
264
0.28482
10
50
20.7184
50
122
3.45097
90
194
0.85248
130
266
0.2777
11
52
19.6891
51
124
3.31847
91
196
0.82643
131
268
0.27078
12
54
18.7177
52
126
3.19183
92
198
0.80132
132
270
0.26408
13
55
17.8005
53
127
3.07075
93
199
0.77709
133
271
0.25757
14
57
16.9341
54
129
2.95896
94
201
0.75373
134
273
0.25125
15
59
16.1156
55
131
2.84421
95
203
0.73119
135
275
0.24512
16
61
15.3418
56
133
2.73823
96
205
0.70944
136
277
0.23916
17
63
14.6181
57
135
2.63682
97
207
0.68844
137
279
0.23338
18
64
13.918
58
136
2.53973
98
208
0.66818
138
280
0.22776
19
66
13.2631
59
138
2.44677
99
210
0.64862
139
282
0.22231
58
Appendix 2 Temperature Sensor Resistance Value Table for T5 (°C --K)
°C
°F
K Ohm
°C
°F
°C
K Ohm
°F
K Ohm
°C
°F
K Ohm
-20
-4
542.7
20
68
68.66
60
140
13.59
100
212
3.702
-19
-2
511.9
21
70
65.62
61
142
13.11
101
214
3.595
-18
0
483
22
72
62.73
62
144
12.65
102
216
3.492
-17
1
455.9
23
73
59.98
63
145
12.21
103
217
3.392
-16
3
430.5
24
75
57.37
64
147
11.79
104
219
3.296
-15
5
406.7
25
77
54.89
65
149
11.38
105
221
3.203
-14
7
384.3
26
79
52.53
66
151
10.99
106
223
3.113
-13
9
363.3
27
81
50.28
67
153
10.61
107
225
3.025
-12
10
343.6
28
82
48.14
68
154
10.25
108
226
2.941
-11
12
325.1
29
84
46.11
69
156
9.902
109
228
2.86
-10
14
307.7
30
86
44.17
70
158
9.569
110
230
2.781
-9
16
291.3
31
88
42.33
71
160
9.248
111
232
2.704
-8
18
275.9
32
90
40.57
72
162
8.94
112
234
2.63
-7
19
261.4
33
91
38.89
73
163
8.643
113
235
2.559
-6
21
247.8
34
93
37.3
74
165
8.358
114
237
2.489
-5
23
234.9
35
95
35.78
75
167
8.084
115
239
2.422
-4
25
222.8
36
97
34.32
76
169
7.82
116
241
2.357
-3
27
211.4
37
99
32.94
77
171
7.566
117
243
2.294
-2
28
200.7
38
100
31.62
78
172
7.321
118
244
2.233
-1
30
190.5
39
102
30.36
79
174
7.086
119
246
2.174
0
32
180.9
40
104
29.15
80
176
6.859
120
248
2.117
1
34
171.9
41
106
28
81
178
6.641
121
250
2.061
2
36
163.3
42
108
26.9
82
180
6.43
122
252
2.007
3
37
155.2
43
109
25.86
83
181
6.228
123
253
1.955
4
39
147.6
44
111
24.85
84
183
6.033
124
255
1.905
5
41
140.4
45
113
23.89
85
185
5.844
125
257
1.856
6
43
133.5
46
115
22.89
86
187
5.663
126
259
1.808
7
45
127.1
47
117
22.1
87
189
5.488
127
261
1.762
8
46
121
48
118
21.26
88
190
5.32
128
262
1.717
9
48
115.2
49
120
20.46
89
192
5.157
129
264
1.674
10
50
109.8
50
122
19.69
90
194
5
130
266
1.632
11
52
104.6
51
124
18.96
91
196
4.849
12
54
99.69
52
126
18.26
92
198
4.703
13
55
95.05
53
127
17.58
93
199
4.562
14
57
90.66
54
129
16.94
94
201
4.426
15
59
86.49
55
131
16.32
95
203
4.294
16
61
82.54
56
133
15.73
96
205
4.167
17
63
78.79
57
135
15.16
97
207
4.045
18
64
75.24
58
136
14.62
98
208
3.927
19
66
71.86
59
138
14.09
99
210
3.812
59
Appendix 3:
ΔT(℉) =
°C
°F
°C
°F
°C
-5
23
21
69.8
51
-4
24.8
22
71.6
52
-3
26.6
23
73.4
-2
28.4
24
-1
30.2
0
9ΔT(℃)
5
°F
°C
°F
°C
°F
123.8
82
179.6
113
235.4
125.6
83
181.4
114
237.2
53
127.4
84
183.2
115
239
75.2
54
129.2
85
185
116
240.8
25
77
55
131
86
186.8
117
242.6
32
25.5
77.9
56
132.8
87
188.6
118
244.4
0.5
32.9
26
78.8
57
134.6
88
190.4
119
246.2
1
33.8
27
80.6
58
136.4
89
192.2
120
248
1.5
34.7
28
82.4
59
138.2
90
194
121
249.8
2
35.6
29
84.2
60
140
91
195.8
122
251.6
2.5
36.5
30
86
61
141.8
92
197.6
123
253.4
3
37.4
31
87.8
62
143.6
93
199.4
124
255.2
3.5
38.3
32
89.6
63
145.4
94
201.2
125
257
4
39.2
33
91.4
64
147.2
95
203
126
258.8
4.5
40.1
34
93.2
65
149
96
204.8
127
260.6
5
41
35
95
66
150.8
97
206.6
128
262.4
6
42.8
36
96.8
67
152.6
98
208.4
129
264.2
7
44.6
37
98.6
68
154.4
99
210.2
130
266
8
46.4
38
100.4
69
156.2
100
212
131
267.8
9
48.2
39
102.2
70
158
101
213.8
132
269.6
10
50
40
104
71
159.8
102
215.6
133
271.4
11
51.8
41
105.8
72
161.6
103
217.4
134
273.2
12
53.6
42
107.6
73
163.4
104
219.2
135
275
13
55.4
43
109.4
74
165.2
105
221
136
276.8
14
57.2
44
111.2
75
167
106
222.8
137
278.6
15
59
45
113
76
168.8
107
224.6
138
280.4
16
60.8
46
114.8
77
170.6
108
226.4
139
282.2
17
62.6
47
116.6
78
172.4
109
228.2
140
284
18
64.4
48
118.4
79
174.2
110
230
141
285.8
19
66.2
49
120.2
80
176
111
231.8
142
287.6
20
68
50
122
81
177.8
112
233.6
143
289.4
60
2.Compressor checking
Measure the resistance value of each winding by using the tester.
Position
Blue - Red
Blue - Black
Resistance Value
DA110S1C-30FZ
DA130M1C-31FZ
DA250S2C-30MT
0.8Ω
1.77Ω
0.55Ω
(20°C /68°F)
(20°C /68°F)
(20°C /68°F)
Red - Blue
61
3. IPM continuity check
Turn off the power, let the large capacity electrolytic capacitors discharge completely, and dismount the IPM. Use a digital
tester to measure the resistance between P and UVWN; UVW and N.
Digital tester
(+)Red
Normal resistance value
(+)Red
(-)Black
N
P
Digital tester
(-)Black
U
U
∞
V
(Several MΩ)
∞
V
N
W
W
(+)Red
4: Indoor AC Fan Motor
Measure the resistance value of each winding by using the tester.
Position
Resistance Value
RPG13B
Black - Red
White - Black
100.5Ω±8%
100Ω±8%
(20°C /68°F)
(20°C /68°F)
(Brand: Weiling)
(Brand: Dayang)
64.5Ω±8%
68.5Ω±8%
(20°C /68°F)
(20°C /68°F)
(Brand: Weiling)
(Brand: Dayang)
62
Normal resistance value
(Several MΩ)
5: Pressure On Service Port
Cooling chart:
°F(°C)
ODT
IDT
75
85
95
105
115
(23.89)
(29.44)
(35)
(40.56)
(46.11)
BAR
70/59
8.2
7.8
8.1
8.6
10.1
BAR
75/63
8.6
8.3
8.7
9.1
10.7
BAR
80/67
9.3
8.9
9.1
9.6
11.2
75
85
95
105
115
(23.89)
(29.44)
(35)
(40.56)
(46.11)
°F(°C)
ODT
IDT
PSI
70/59
119
113
117
125
147
PSI
75/63
124
120
126
132
155
PSI
80/67
135
129
132
140
162
75
85
95
105
115
(23.89)
(29.44)
(35)
(40.56)
(46.11)
°F(°C)
ODT
IDT
MPA
70/59
0.82
0.78
0.81
0.86
1.01
MPA
75/63
0.86
0.83
0.87
0.91
1.07
MPA
80/67
0.93
0.89
0.91
0.96
1.12
12.0
10.0
8.0
70/59
6.0
75/63
80/67
4.0
2.0
0.0
75 (23.89) 85 (29.44)
95 (35)
105 (40.56) 115 (46.11)
63
Heating Chart:
ODT
°F
(°C)
IDT
57/53
47/43
37/33
27/23
17/13
(13.89/11.67)
(8.33/6.11)
(2.78/0.56)
(-2.78/-5)
(-8.33/-10.56)
BAR
55
30.3
28.5
25.3
22.8
20.8
BAR
65
32.5
30.0
26.6
25.4
23.3
BAR
75
33.8
31.5
27.8
26.3
24.9
57/53
47/43
37/33
27/23
17/13
(13.89/11.67)
(8.33/6.11)
(2.78/0.56)
(-2.78/-5)
(-8.33/-10.56)
ODT
°F
(°C)
IDT
PSI
55
439
413
367
330
302
PSI
65
471
435
386
368
339
PSI
75
489
457
403
381
362
57/53
47/43
37/33
27/23
17/13
(13.89/11.67)
(8.33/6.11)
(2.78/0.56)
(-2.78/-5)
(-8.33/-10.56)
ODT
°F
(°C)
IDT
MPA
55
3.03
2.85
2.53
2.28
2.08
MPA
65
3.25
3.00
2.66
2.54
2.33
MPA
75
3.38
3.15
2.78
2.63
2.49
40.0
35.0
30.0
25.0
55
20.0
65
15.0
75
10.0
5.0
0.0
57/53
(13.89/11.67)
47/43
(8.33/6.11)
37/33
(2.78/0.56)
27/23
(-2.78/-5)
64
17/13
(-8.33/-10.56)
10. Exploded View(Version of 2013.07.19)
10.1 Indoor unit
MS11M-09HRFN1-MW0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
1
2
3
3.1
Name
Qty
BOM Code
No.
Part
Name
Qty
BOM Code
Panel assembly
1
201132590959
15
Horizontal louver
1
201132590956
Air filter
2
201132590962
16
Chassis assembly
1
201132590963
1
203332390972
16.1
Louver motor
1
202400200031
1
201332391249
17
Pipe clamp board
1
201119900949
1
201119900948
18
Installation plate
1
201232590037
1
201132590958
19
1
203332391073
1
201132490125
1
201132490139
1
201332391485
Display box
assembly
Display board
assembly
Cover of indoor
4
electronic control
box
5
Panel frame
assembly
5.1
Screw cap
2
201119900950
19.1
6
Drain hose
1
201101020038
19.2
7
Pipe nut
1
201600330002
19.3
65
Electronic control
box assembly
Electronic control
box I
Electronic control
box II
Main control board
assembly
Ambient
7
Pipe nut
1
201600330001
19.4
temperature sensor
1
202433190000
1
202301300584
1
202301450119
1
201132490126
assembly
8
9
10
11
Fix clamp of
temperature sensor
Evaporator
assembly
Fan motor cover
Asynchronous
motor
Pipe temperature
1
201102000305
19.5
1
201532590453
19.6
1
201132490127
20
1
202400370022
21
Remote Controller
1
203355091532
sensor assembly
Wire joint
Cover of electronic
control box
12
Bearing holder
1
201119900952
22
Seal
1
202720090001
13
Bearing base
1
202719900606
23
Drain joint
1
201101020011
14
Cross flow fan
1
201100200054
24
Air freshening filter
1
201131410703
66
MS11M-12HRFN1-MV0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
1
2
3
3.1
Name
Qty
BOM Code
No.
Part
Name
Qty
BOM Code
Panel assembly
1
201132590959
15
Horizontal louver
1
201132590956
Air filter
2
201132590962
16
Chassis assembly
1
201132590963
1
203332390972
16.1
Louver motor
1
202400200031
1
201332391249
17
Pipe clamp board
1
201119900949
1
201119900948
18
Installation plate
1
201232590037
1
201132590958
19
1
203332591105
1
201132490125
1
201132490139
1
201332591013
1
202433190000
1
202301300584
Display box
assembly
Display board
assembly
Cover of indoor
4
electronic control
box
5
Panel frame
assembly
5.1
Screw cap
2
201119900950
19.1
6
Drain hose
1
201101020038
19.2
7
Pipe nut
1
201600330003
19.3
Electronic control
box assembly
Electronic control
box I
Electronic control
box II
Main control board
assembly
Ambient
7
Pipe nut
1
201600330001
19.4
temperature sensor
assembly
8
Fix clamp of
temperature sensor
1
201102000305
19.5
67
Pipe temperature
sensor assembly
9
10
11
Evaporator
assembly
Fan motor cover
Asynchronous
motor
1
201532590458
19.6
1
201132490127
20
1
202400370022
21
Wire joint
1
202301450119
1
201132490126
Remote Controller
1
203355091532
Cover of electronic
control box
12
Bearing holder
1
201119900952
22
Seal
1
202720090001
13
Bearing base
1
202719900606
23
Drain joint
1
201101020011
14
Cross flow fan
1
201100200054
24
Air freshening filter
1
201131410703
68
MS11M-18HRFN1-MU0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
1
2
3
3.1
Name
Qty
BOM Code
No.
Part
Panel assembly
1
201132890674
15
Air filter
2
201132890670
1
Display box
assembly
Display board
assembly
Name
Qty
BOM Code
Bearing holder
1
201119900952
16
Bearing base
1
202719900606
203332390972
17
Cross flow fan
1
201100200056
1
201332391249
18
Chassis assembly
1
201132890703
1
201133091048
19
Pipe clamp board
1
201232800103
1
201132890673
20
Installation plate
1
201232590038
1
203332890569
1
202301450119
1
201133090976
1
201332890610
Cover of indoor
4
electronic control
box
5
Panel frame
assembly
5.1
Screw cap
3
201119900950
21
6
Horizontal louver
1
201132890671
21.1
7
Air outlet assembly
1
201132890677
21.2
7.1
Louver motor
1
202400200120
21.3
69
Electronic control
box assembly
Wire joint
Electronic control
box
Main control board
assembly
Ambient
8
Drain hose
1
201101020038
21.5
temperature sensor
1
202432390005
1
202301300584
1
201133090981
assembly
Pipe temperature
9
Pipe nut
1
201600330001
21.6
9
Pipe nut
1
201600330003
22
1
201102000305
23
Remote Controller
1
203355091532
1
201532890153
24
Seal
1
202720090001
1
201133090980
25
Drain joint
1
201101020011
1
201133090167
26
Air freshening filter
1
201131410703
1
202400300064
10
11
12
13
14
Fix clamp of
temperature sensor
Evaporator
assembly
Fan motor cover
Fixing board of fan
motor
Asynchronous
motor
70
sensor assembly
Cover of electronic
control box
MS11M-24HRDN1-MT0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
1
2
3
3.1
Name
Qty
BOM Code
No.
Part
Panel assembly
1
201133090997
17
Air filter
2
201133090992
1
Display box
assembly
Display board
assembly
Qty
BOM Code
Cross flow fan
1
201100200057
18
Chassis assembly
1
201133090995
203332390972
19
Pipe clamp board
1
201133090989
1
201332391249
20
Installation plate
1
201232990002
1
201119900948
21
1
203333090465
1
201133090996
21.1
1
202301450119
1
201133190200
1
201333090678
1
202430790040
1
202301300426
1
201133190184
Cover of indoor
4
electronic control
box
5
Panel frame
assembly
5.1
Screw cap
4
201119900950
21.2
7
Air outlet assembly
1
201133091008
21.3
Name
Electronic control
box assembly
Wire joint
Electronic control
box
Main control board
assembly
Ambient
7.1
Louver motor
1
202400200070
21.5
temperature sensor
assembly
8
Drain hose
1
201101020038
21.6
9
Pipe nut
1
201600330004
21.7
71
Pipe temperature
sensor assembly
Cover of electronic
control box
9
10
11
12
14
Pipe nut
Fix clamp of
temperature sensor
Evaporator
assembly
Fan motor cover
Asynchronous
motor
21.1
Fan motor
0
capacitor
201102000305
23
1
201533090129
1
1
201600330002
1
202401100354
1
Remote Controller
1
203355091532
24
Seal
1
202720090001
201133090991
25
Drain joint
1
201101020011
1
202400401301
26
Air freshening filter
1
201131410703
1
201133090993
1
201133090999
15
Bearing holder
1
201119900952
27
16
Bearing base
1
202719900606
28
72
Horizontal louver
(above)
Horizontal louver
(below)
10.2 Outdoor unit
MOC-09HFN1-MW0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
Name
Qty
BOM Code
No.
Part
1
202301300115
17
1
2011374G0003
18
1
201537690004
19
1
202440500004
20
Name
Qty
BOM Code
Left supporter
1
201237400400
Top cover assembly
1
201237900028
1
203337390226
1
203337590049
Ambient
1
temperature
sensor assembly
2
3
4
Rear net
Condenser
assembly
Pipe temperature
sensor assembly
Electronic control
box assembly
Terminal board
assembly
5
Valve plate
1
201237200282
20.1
Wire joint
1
202301400256
6
Chassis assembly
1
201237590091
20.2
Terminal board
1
201237590046
1
201237590080
21
1
201637391606
7
Rear right
clapboard
4-Ways valve
assembly
8
Big handle
1
201237390104
21.1
Gas valve
1
201600720095
9
Water collector
1
201137400000
21.2
4-Ways valve
1
201600690010
10
Air outlet grille
1
201237390105
22
1
201637391145
11
Clamp of front net
6
201135110801
22.1
1
201600740523
1
201601300554
Liquid valve
assembly
Liquid valve
Electronic
12
Front panel
1
201237400392
22.2
expansion valve
assembly
73
13
14
Axial flow fan
Asynchronous
motor
1
201100390002
23
1
202400300060
24
Supporter
15
assembly of fan
Partition board
assembly
Crankcase electric
heater
1
201400601510
1
202403100501
1
202301310068
1
202301000867
Discharge
1
201237390026
25
motor
16
Compressor
temperature sensor
assembly
1
201237500259
27
74
Reactor
MOC-12HFN1-MV0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
Name
Qty
BOM Code
No.
Part
1
202301300115
17
18
Name
Qty
BOM Code
Left supporter
1
201237400400
Top cover assembly
1
201237900028
1
203337590101
1
203337590049
Ambient
1
temperature sensor
assembly
2
3
4
Rear net
Condenser
assembly
Pipe temperature
sensor assembly
1
2011374G000
3
1
201537690004
19
1
202440500004
20
Electronic control
box assembly
Terminal board
assembly
5
Valve plate
1
201237200282
20.1
Wire joint
1
202301400256
6
Chassis assembly
1
201237590091
20.2
Terminal board
1
201237590046
1
201237590080
21
1
201637591413
Rear right
7
clapboard
assembly
4-Ways valve
assembly
8
Big handle
1
201237390104
21.1
Gas valve
1
201600720195
9
Water collector
1
201137400000
21.2
4-Ways valve
1
201600690010
10
Air outlet grille
1
201237390105
22
1
201637391145
75
Liquid valve
assembly
11
Clamp of front net
6
201135110801
22.1
Liquid valve
1
201600740523
1
201601300554
1
201400601510
1
202403100501
1
202301310068
1
202301000867
Electronic
12
Front panel
1
201237400392
22.2
expansion valve
assembly
13
14
Axial flow fan
Asynchronous
motor
1
201100390002
23
1
202400300060
24
Supporter
15
assembly of fan
Partition board
assembly
Crankcase electric
heater
Discharge
1
201237390026
25
motor
16
Compressor
temperature sensor
assembly
1
201237500259
27
76
Reactor
MOF-18HFN1-MU0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
No.
Part
Name
Qty
BOM Code
No.
1
202301310075
20
Ambient
1
temperature sensor
assembly
2
3
4
Rear net
Condenser
assembly
Pipe temperature
sensor assembly
1
2011481G000
21
1
Electronic control
box assembly
Terminal board
assembly
Qty
BOM Code
1
203337890332
1
203337990161
201537890068
21.1
Wire joint
1
202301400256
1
202440500004
21.2
Terminal board
1
201237890064
1
201637891245
1
201600700078
1
201601300554
1
201637891247
Valve plate
1
201237300285
22
6
Chassis assembly
1
201257090054
22.1
Rear right
clapboard
Name
1
5
7
Part
Liquid valve
assembly
Liquid valve
Electronic
1
201237890100
22.2
assembly
expansion valve
assembly
4-way valve
8
Big handle
1
201237390104
23
9
Water collector
1
201137390017
23.1
Gas valve
1
201600720194
1
201248100389
23.2
4-Ways valve
1
201600690011
1
201248100390
24
Compressor
1
201400603269
assembly
Front right
10
clapboard
assembly
11
Front panel
77
12
Air outlet grille
1
201237890112
25
13
Axial flow fan
1
201145500002
26
Crankcase
electric heater
1
202403100501
1
202301310068
1
201248090001
Discharge
temperature
sensor assembly
14
Asynchronous
motor
Cover of
1
202400300033
27
1
201257090031
28
Reactor
1
202301000820
inductance
Supporter
15
assembly of fan
motor
16
Rear supporter
1
201248100384
28
Reactor
1
202301000819
17
Top cover assembly
1
201248100363
30
Clamp of front net
8
201135110801
18
Left supporter
1
201248100367
31
1
202401000078
1
201237790031
32
1
201200100002
19
Partition board
assembly
78
Capacitor of
compressor
Capacitor clip
MOG-24HFN1-MT0W:
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
W310-BP-R-001-1
No.
Part
Name
Qty
BOM Code
No.
1
202301310075
20.2
Ambient
1
temperature sensor
assembly
2
3
4
Rear net
Condenser
assembly
Pipe temperature
sensor assembly
1
2011482G000
20.3
1
1
201538090077
20.4
1
202301300111
20.5
Part
Name
Main control
board assembly
Inverter control
board assembly
Installation board
for E-parts
Radiator
Installation plate
Qty
BOM Code
1
201338090071
1
201357190085
1
201157190010
1
202301901173
1
201295200010
1
203338090315
5
Valve plate
1
201248300316
20.6
6
Chassis assembly
1
201257190085
21
1
201238090067
21.1
Wire joint
1
202301450155
Terminal board
1
201257190116
1
201638091091
of PCB
Terminal board
assembly
Rear right
7
clapboard
assembly
8
Big handle
1
201237390104
21.2
9
Water collector
1
201138090002
22
79
Liquid valve
assembly
Front right
10
clapboard
1
201248200082
22.1
Liquid valve
1
201600740706
1
201601300032
1
201638091121
assembly
Electronic
11
Front panel
1
201248200103
22.3
12
Air outlet grille
1
201238090068
23
13
Axial flow fan
1
201100300527
23.1
Gas valve
1
201600720398
1
202400300047
23.2
4-Ways valve
1
201600600119
1
201257190071
24
Compressor
1
201400601740
1
201248200095
25
1
202403101715
1
202448200000
1
201248390003
14
Asynchronous
motor
expansion valve
4-way valve
assembly
Supporter
15
assembly of fan
motor
16
Rear supporter
Crankcase
electric heater
Discharge
17
Top cover assembly
1
201248300309
26
temperature
sensor assembly
18
19
20
20.1
Left supporter
Partition board
assembly
Electronic control
box assembly
Cover of electronic
control box
Cover of
1
201248400036
27
1
201257190115
28
Reactor
1
202301000943
1
203338090316
29
Small Handle
2
201148700009
1
201157190011
80
inductance
11 Disassembly Instructions
Note: This part is for reference, the photos may have slight difference with your machine.
11.1 Indoor unit
No.
Parts name
Procedures
Remarks
1
Front panel
How to remove the front
panel.
Overview:
1) Pull the below side of
the panel and release the
clips. Then remove the
front panel.
2) Remove the filter and
horizontal louver.
3) Remove the four
fixing screws.
4) Remove the cover
(one screw).
Panel
One screw
fixing the cover
Clip
Clip
Filter
5) Lift the panel frame
and release the connector
of display ass’y.
connectors. Then remove
the panel frame
assembly.
Four screws
Connector for
display ass’y
81
2
Electrical
parts
How to remove the
electrical parts.
1) After remove the
front panel from
procedure 1, pull out the
room temp. sensor and
evaporator coil sensor.
Remove the grounding
screws.
2) Pull out the clip
toward the left side and
open the cover.
Room temp.
Grounding screws
sensor
Swing motor
3) Remove the fixing
screw and open the
electrical box cover.
.
Clip for electronic
Evaporator coil
control box cover
temp. sensor
4) Pull out the
connectors of the swing
motor and fan motor .
5) Remove the fixing
screw and then remove
the electronic control box
and air outlet ass’y.
Fan motor connector
and swing motor
82
Fixing screw
3
Evaporator
How to remove the
evaporator.
1) After remove the front
panel ass’y and electrical
parts following procedure
1 and procedure 2,
remove the pipe holder at
the rear side of the unit.
2) Remove the two
screws on the evaporator
at the base bearing side.
3) Remove two screws
on the evaporator at the
fixed plates and then lift
the evaporator ass’y.
Two screws at the base bearing side
Two
screws at
the fixed
plates
83
4
Fan and
motor
How to remove the fan
and motor.
1) After remove the
evaporator ass’y
following procedure 1,
procedure 2 and
procedure 3, remove the
three screws fixing the
cover
2) Remove the screw
fixing the motor and then
pull out the motor.
Three screws
One screw
84
11.2 Outdoor unit

MOC-09HFN1-MTOW, MOC-12HFN1-MTOW
No.
Part name
Procedures
1
Panel plate
How to remove the panel
plate.
1) Stop operation of the
air conditioner and turn
“OFF” the power breaker.
Remarks
Screws of top panel
2) Refer to the right side
photos, find out the fixing
screws of the panels.
Screws of front panel
Screw of
top panel
3) Remove the screws of
top panel and remove the
top panel.
Screws of
Screws of
big handle
front panel
on right
side plate.
Screws of
water connector
on right side
Screw of right side plate
plate
85
Screw of
the top
4) Remove the screws of
the front panel, including
the fixing screws of motor
holder and then remove
the front panel.
panel
Screws of right rear plate
5) Remove the screws of
the right side plate and
remove the right side
plate.
Screw of
top panel
Screws of front panel
Screws of the motor holder
86
2
Fan ass’y
How to remove the fan
ass’y.
Electronic control box
Fan ass’y
1) After remove the
panel plate following
procedure 1, remove the
hex nut fixing the fan and
then remove the fan.
Reactor
Compressor and liquid-gas separator
Nut fixing the fan
2) Unfix the hooks and
then open the electronic
control box cover.
87
Fan motor connector
3) Disconnect the
connector for fan motor
from the electronic control
board.
4) Remove the four
fixing screws of the fan
motor.
5) Then remove the fan
motor.
3
Electrical
parts
Four
screws
How to remove the
electrical parts.
1) After finish work of
item 1 and item 2, remove
the three connectors for
the compressor and
electrical heaters.
Reactor connector
Compressor
connector and
2) Release the
connector of the reactor.
electrical heater
connector
88
3) Pull out the two blue
wires connected with the
four way valve.
Two blue wires of four way valve
4) Pull out connectors of
the compressor top temp.
sensor, condenser coil
temp. sensor(T3),outdoor
ambient temp. sensor(T4)
and discharge temp.
sensor(T5).
Four connectors of temp. sensors.
5) Remove the ground
wires .
6) Remove the power
supply wires(L1,L2,S).
7) Then remove the
electronic control box.
89
4
Four-way
valve
How to remove the
four-way valve.
1) Perform work of item
1,2,3.
2) Recover refrigerant
from the refrigerant circuit.
3) Remove the screw of
the coil and then remove
the coil.
4) Detach the welded
parts of four-way valve
and pipe.
5) Then the four-way
valve ass’y can be
removed
The picture of four-way valve may be different from
the one on your side.
Four-way
valve
Welded
parts
Coil of four-way valve, fixing by one screw.
5
Compressor
How to remove the
compressor.
1) After perform work of
item1,2,3.
2) Remove the
discharge pipe and suction
pipe with a burner.
3) Remove the hex nuts
and washers fixing the
compressor on bottom
plate.
4) Lift the compressor
from the base pan
assembly.
Discharge
pipe and
suction
pipe
Nuts of
compress
90

No.
MOF-18HFN1-MU0W
Part name
Procedures
Panel plate
How to remove the panel
plate.
1) Stop operation of
the air conditioner and turn
“OFF” the power breaker.
Remarks
Screws of top panel
2) Refer to the right side
photos, find out the fixing
screws of the panels.
Screws of front panel
3) Remove the screws of
top panel and remove the
top panel.
Screw of
top panel
Screws of
big handle
4) Remove the screws of
the front panel, including
the fixing screws of motor
holder and then remove
the front panel.
Screws of
on right
front panel
side plate.
Screws of
water connector
on right side
plate
91
Screw of
5) Remove the screws of
the right side plate and
remove the right side
plate.
the top
panel
Screws of right rear plate
Screw of
top panel
Screws of
front panel
Screws of the motor holder
92
2
Fan ass’y
How to remove the fan
ass’y.
Fan
Electronic control box
1) After remove the panel
plate following procedure
1, remove the hex nut
fixing the fan and then
remove the fan.
Two reactors
Compressor and
liquid-gas separator
2) Remove the one fixing
screw. Unfix the hooks and
then open the electronic
control box cover.
Nut fixing the fan
3) Release the fan motor
connector and four way
valve connector.
4) Remove the four
fixing screws of the fan
motor.
5) Then remove the fan
motor.
93
Fan motor connector
Four way valve
connector
Four screws
3
Electrical
parts
How to remove the
electrical parts.
1) After finish work of
item 1 and item 2, remove
the two connectors for the
compressor and the
compressor crankcase
heater.
2) Release the three
temp. sensor connectors.
94
3) Remove the connector
of reactor.
4) Remove the connector
of electronic expansion
valve.
5) Remove the
grounding screw.
6) Remove the power
supply wires(L1,L2,S).
7) Then remove the
electronic control box.
95
4
Four-way
valve
How to remove the
four-way valve.
1) Perform work of
item1,2,3.
2) Recover refrigerant
from the refrigerant circuit.
3) Remove the screw of
the coil and then remove
the coil.
4) Detach the welded
parts of four-way valve
and pipe.
5) Then the four-way
valve ass’y can be
removed
The picture of four-way valve may be different from
the one on your side.
Four-way
valve
Welded
parts
Coil of four-way valve, fixing by one screw.
5
Compressor
How to remove the
compressor.
1) After perform work of
item1,2,3.
2) Remove the
discharge pipe and suction
pipe with a burner.
3) Remove the hex nuts
and washers fixing the
compressor on bottom
plate.
4) Lift the compressor
from the base pan
assembly.
Discharge
pipe and
suction
pipe
Nuts of
compressor
96

MOG-24HFN1-MT0W
No.
Part name
Procedures
1
Panel plate
How to remove the panel
plate.
1) Stop operation of
the air conditioner and turn
“OFF” the power breaker.
Remarks
Screws of top panel
2) Refer to the right side
photos, find out the fixing
screws of the panels.
3) Remove the screws of
top panel and remove the
top panel.
Screws of front panel
Screws of the right
side panel
Screws of
big handle
on right
side plate.
4) Remove the screws of
the front panel, including
the fixing screws of motor
holder and then remove
the front panel.
Screws of
water connector
Screws of
front panel
97
on right side
plate
5) Remove the screws of
the right side plate and
remove the right side
plate.
Screw of the top panel
Screws of right rear plate
Screw of
top panel
Screws of
front panel
Screws of the motor holder
98
2
Fan ass’y
How to remove the fan
ass’y.
Nut fixing the fan
1) After remove the panel
plate following procedure
1, remove the hex nut
fixing the fan and then
remove the fan.
Electronic control box
Fan
One reactor
Compressor and
liquid-gas separator
99
2) Remove the
connector of the fan motor.
3) Remove the four
screws and the remove
the fan motor.
3
Electrical
parts
How to remove the
electrical parts.
1) After finish work of
item 1 and item 2, remove
the connector of the
compressor.
100
2) Remove the six
screws fixing the IPM
board.
3) Release the three
connectors of the temp.
sensor.
4) Pull out the two blue
wires connected with the
four way valve.
Two blue wires of four way valve
101
5) Pull out the four wires
of electrical heater (three
orange wires, one grey
wire).
6) Pull out connectors of
the compressor top temp.
sensor, condenser coil
temp. sensor(T3),outdoor
ambient temp. sensor(T4)
and discharge temp.
sensor(T5).
Four temp. sensor connectors
7) Remove the
grounding screw.
Grounding screw
102
8) Remove the power
supply wires(L1,L2,S).
9) Then remove the
electronic control box.
4
Four-way
valve
How to remove the
four-way valve.
1) Perform work of
item1,2,3.
2) Recover refrigerant
from the refrigerant circuit.
3) Remove the screw of
the coil and then remove
the coil.
4) Detach the welded
parts of four-way valve
and pipe.
5) Then the four-way
valve ass’y can be
removed
The picture of four-way valve may be different from
the one on your side.
Four-way
valve
Welded
parts
Coil of four-way valve, fixing by one screw.
103
5
Compressor
How to remove the
compressor.
1) After perform work of
item1,2,3.
2) Remove the
discharge pipe and suction
pipe with a burner.
3) Remove the hex nuts
and washers fixing the
compressor on bottom
plate.
4) Lift the compressor
from the base pan
assembly.
Discharge
pipe and
suction
pipe
Nuts of
compressor
104
Download PDF
Similar pages