INSTALLATION INSTRUCTIONS
50kg
(110lbs)
MAX
LED WALL MOUNT
7
Model: LED-01
Max Load Capacity: 50kg(110lbs)
NOTE: Read entire instruction sheet before you start installtion and assembly.
Component Checklist
IMPORTANT: Ensure you have received all parts against the component checklist prior to installing.If any parts
are missing or faulty, telephone the special franchiser for a placement.
WARNING
• Do not begin to install your product until you have and understood the instructions
and warnings contained in this Installation Sheet. If you have any question regarding
any of the instruction or warning, Please contact your local distributor.
wall plate (x2)
A
Adapter bracket (x1)
B
• Please refer to manufacturer’s installation guide recommendation for required
distance from wall to avoid risk of property damage.
• This product should only be installed by someone of good mechanical aptitude, has
experience with basic building construction , and fully understand these instructions.
Supporting spacer (x1)
C
Supporting spacer (x1)
D
Package M
• Make sure that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity.
M8x20 (x4)
M-A
M8x40 (x4)
M-B
Ø8 Washer (x4)
M-C
• If mounting to wood wall studs, make sure that mounting screws are anchored into
the center of the studs. Use of an “edge to edge” stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
Ø17.5xØ8x20 (x4)
M-D
Ø 16x Ø 8.2 Washer (x4)
M-E
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items,
greatly reducing their holding power.
• This products intended for indoor use only. Use of this product outdoors could lead to
product failure and personal injury.
Package W
M5x50 lag bolt (x2)
W-A
concrete anchor (x2)
W-B
Ø 16x Ø 6.2 Washer (x2)
W-C
Tools required
·Phillips Head Screw driver(200mm length exclude the handle)
·M6 Socket and Wrench
·Electric drill and 10mm masonry bit for concrete wall installation
·Marking Pen
·Hammer
1
2
1a
• Use the Wall Plate as a template to mark 2 holes locations on the wall, make sure the mounting hold at the
WOOD STUD WALL MOUNTING:
same level. as shown in fig.1.2.
• Pre-drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a Concrete Anchor (W-B)
WARNING
into each of these holes. Attach the Wall Plate to the wall using 2 Lag Bolts (W-A) and 2 M6 Washers (W-C),
as in fig.1.3.
• Make sure that the supporting surface will safely support the combined load of the equipment
and all attached hardware and components.
• Tighten wood screws firmly, but do not overtighten. Overtightening can damage the screws,
greatly reducing their holding power.
W-C
W-B
350mm-400mm
• Make sure that mounting screws are anchored into the center of the studs. Use of an “edge to
edge” stud finder is highly recommended.
W-A
• Hardware provided is for attachment of mount through standard thickness drywall or plaster
into studs. Installers are responsible to provide hardware for other types of mounting situations.
• Wall plate can be mounted to two studs. Use a stud finder to locate the edges of the studs. Use of an
•
•
edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each
stud’s center.
Place wall plate on wall as a template. And mark the center of the two mounting holes. Make sure that the
mounting holes are on the stud centerline and at the same level.
Drill two 1/8” (3mm) dia. Holes 1.2” (30mm) deep, secure it using two lag bolts (W-A) and two M6 washers
(W-C) as shown in fig. 1.1.
fig. 1.2
2
fig. 1.3
Installing Adapter Brackets
• To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the
screen.
• Place screen face side down. Place adapter bracket and supporting spacer on the back of screen, align
to holes, as shown in fig.2.1.
3mm
• Attach the adapter brackets and supporting spacer to the back of the screen using the appropriate
Stud
combination of screws, washers, and spacers, as shown in fig.2.2 , and fig.2.3.
W-C
W-A
fig. 1.1
1b
SOLID BRICK AND CONCRETE BLOCK MOUNTING:
WARNING
• When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8” of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar
joints! Be sure to mount in a solid part of the block, generally 1” minimum from the side of the
block. It is suggested electric drill on slow setting is used to drill the hole instead of a hammer
drill to avoid breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
3
fig. 2.1
NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to
step 2-2.
4
2
1
For Flat Back Screen
• Begin with the shortest length screw, hand thread through washer and adapter bracket into screen as shown
3
Hang the brackets mounted TV onto the wall plate
Warning: A minimum of two qualified people are required for this operation.
below.
• Screw must make at least three full turns into mounting hole and fit snug into place. Do not over tighten.
• If screw cannot make three full turns into screen, select a longer length screw from the baffled fastener pack.
Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacer may not be used, depending upon the type of screen.
• After the wall mount has been safely secured to the wall, with 2 people carefully lift your TV and hook the
top hooks over the top of the wall plate rail. , see Fig. 3-1.
M-C
M-E
M-A
M-C
M-E
M-A
fig. 3.1
fig. 2.2
2
2
For Bump-out or Recessed Back Screen
Begin with longer length screw, hand thread through washer, the supporting spacers and sliders into screen as
shown below. Screw must make at least three full turns into mounting hole and fit snug into place. Do not over
tighten. If screw cannot make three full turns into screen, select a longer length screw from the baffled fastener
pack. Repeat for remaining mounting holes and tighten screws.
4
Cable Management
• Slowly pull bottom of display away from wall until kickstand of the supporting spacer(D) fully reaches its
down position.
•Attach or adjust cables as necessary on back of display.
•To disengage kickstand, slightly pull display away from wall. Slowly allow display to return to the wall.
M-E
M-D
M-C
M-B
M-E
M-D
M-C
M-B
fig. 2.3
5
fig. 4.1
6
Download PDF
Similar pages