™
SCOOTER
Owner’s Manual
Read and understand this entire manual before
allowing child to use this product!
For assistance contact Razor. DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
Version: 2_09_10
Item Number:
Black
Blue
Purple
13010800
13010840
13010850
Contents
Safety Warnings............................................................. 1
Before You Begin............................................................ 2
Set Up and Usage Instructions.................................... 3-4
Check Before Riding....................................................... 5
Scooter Parts List........................................................... 6
Safety Tips...................................................................... 7
Warranty......................................................................... 7
Safety Warnings
AN IMPORTANT MESSAGE TO PARENTS: This manual contains
important information. For your child’s safety, it is your responsibility to
review this information with your child and make sure that your child
understands all warnings, cautions, instructions and safety topics. Razor USA
recommends that you periodically review and reinforce the information in this
manual with younger riders and that you are required to inspect and maintain
your child’s scooter to insure their safety.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Direct parental supervision is required. Scooters are meant to be used only
in controlled environments free of potential traffic hazards and not on public
streets. Do not allow your child to ride a scooter in any areas where vehicle
traffic is present. Child must maintain a hold on the handlebars at all times.
Never allow more than one child at a time to ride a scooter. Never use near
steps, sloped driveways, hills, roadways, alleys or swimming pool areas.
Keep fingers and other body parts away from the product when folding or
unfolding. Adults must not allow children to assist in folding or unfolding the
scooter.
NOTE: The age recommendation for the Graffiti™ scooter is higher than that
of a “basic” scooter because using the chalk device when riding may be more
complicated. Make sure your child is ready!
Do not ride a scooter in wet weather. Scooters are intended for use on solid,
flat, clean and dry surfaces such as pavement or level ground without loose
debris such as rocks or gravel. Wet, slick or uneven and rough surfaces may
impair traction and contribute to possible accidents. Do not ride a scooter in
mud, ice, puddles or water. Avoid excessive speeds that can be associated
with downhill rides. Never risk damaging surfaces such as carpet or flooring
by use of a scooter indoors. Do not ride at night or when visibility is impaired.
GENERAL WARNING: Scooter riding can be a hazardous activity.
Scooters can and are intended to move and it is therefore possible to get into
dangerous situations and/or lose control and/or fall. If such things occur you
can be seriously injured or die. LIKE ANY OTHER MOVING PRODUCT, USING
A SCOOTER CAN BE A DANGEROUS ACTIVITY AND MAY RESULT IN INJURY
OR DEATH EVEN WHEN USED WITH PROPER SAFETY PRECAUTIONS. USE AT
YOUR OWN RISK AND USE COMMON SENSE.
When toggling the chalking mechanism from the OFF to ON position, avoid
sustained downward pressure against the lever mechanism. Sustained
downward pressure can cause the springs to rub directly on the ground.
Sustained rubbing (20+ minutes) will wear down the springs which could
cause the springs to break.
• Do not allow children under age six (6) to use the scooter. Children under
age eight (8) should ride with adult supervision at all times. All children
and preteens should ride with adult guidance at all times.
• Always pay attention to where you are going; do not allow use of the
chalk marking device to distract you from safe riding practices.
CLEAN-UP AND CARE RELATED TO CHALK
• Always wear safety equipment such as helmet, knee pads and elbow
pads. Always wear a helmet when riding your scooter and keep the chinstrap securely buckled.
The chalk provided by Razor with this product is non-toxic. It is designed
and intended for use on hardened asphalt or concrete surfaces, and may be
washed off with water. Use of a brush or broom may assist in removal. Chalk
contains colorants which may cause stains to clothing or other household
items, and should not be used on surfaces less than six months old.
• Always wear shoes.
• Ride on smooth, paved surfaces away from motor vehicles.
PROPER RIDING ATTIRE
• Avoid sharp bumps, drainage grates, and sudden surface changes. Scooter
may suddenly stop.
Always ensure child is wearing proper protective equipment such as an
approved safety helmet. A helmet may be legally required by local law
or regulation in your area. A child should always wear shoes, never ride
barefooted or in sandals, and keep shoelaces tied and out of the way of
the wheels.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other
debris. Wet weather impairs traction, braking, and visibility.
• Do not ride at night.
• Brake will get hot from continuous use. Do not touch after braking.
• Avoid excessive speed associated with downhill rides.
• Adults must assist children in the initial adjustment procedures to unfold
scooter, adjust handlebar and steering to height, and finally to fold scooter.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS
FURTHER INCREASES RISK OF SERIOUS INJURY. USE AT YOUR OWN RISK
AND WITH APPROPRIATE AND SERIOUS ATTENTION TO SAFE OPERATION.
USE CAUTION.
• Obey all local traffic and scootering laws and regulations.
• Watch out for pedestrians.
• Do not exceed 143 pounds (65 kilograms) total weight on the Graffiti ™
scooter.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING. Properly
inspecting and maintaining your scooter can reduce the risk of injury. Always
inspect your scooter before riding and regularly maintain it.
• Rider weight does not necessarily mean a child’s size is appropriate to fit
or maintain control of the scooter.
• A parent’s decision to allow his or her child to ride this product should be
based on the child’s maturity, skill and ability.
WARNING: CHECK LOCAL LAWS REGARDING SCOOTER USE. Check
local laws and regulations to see where and how you may use your Razor
scooter legally. In many states and local areas scooter riders are required
BY LAW to wear a helmet. Check local laws and regulations regarding laws
governing helmet use and scooter operation in your area.
1
Before You Begin
Remove contents from box. Inspect the contents of the box for scratches in the paint and/or dents that may have
occurred during shipping. Because your scooter was assembled and packed at the factory, there should not be any
problems, even if the box has a few scars or dents.
Grip
WARNING: DO
NOT USE NON-RAZOR
PRODUCTS WITH YOUR
SCOOTER.
Razor scooters have been built to
certain Razor design specifications.
The original equipment supplied
at the time of sale was selected
on the basis of its compatibility
with the frame, fork and all other
parts. Certain aftermarket products
may or may not be compatible.
Use of any non-Razor parts and/
or modifications will void the
warranty.
T-tube
Handlebar
Steering tube quick-release
Collar clamp
Steering tube/steering column
Chalk mechanism
Rear fender/brake
Joint lever/pivoting mechanism
Front fork
Deck
Wheels
q Required Tools
5mm
Allen wrench
(Not Included)
Chalk
(Included)
Need Help? Visit www.razor.com for replacement parts, product support and a list of authorized
service centers or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
2
Set up and usage instructions
q Unfolding the scooter for first time use.
1 Insert and secure the left and
right handlebars by pressing the
spring-loaded buttons and
inserting them into the T-bar.
2 Make certain BOTH handlebars
are properly locked onto the T-bar.
3 To release the folding
mechanism, put one foot on the
deck plate and push joint release
lever down. Raise handlebars up
until securely locked in the upright
position.
WARNING: Failure to
properly engage the spring-loaded
buttons may cause the handlebars
to dislodge while riding and may
cause you to lose control and
fall. When correctly engaged the
handlebars will not rotate nor will
they move sideways. Note that
when properly engaged, the springloaded buttons are clearly visible in
the holes on the T-bar.
WARNING: Keep
your fingers clear of the pivoting
mechanism when folding or
unfolding the scooter. Make sure
others are standing clear.
WARNING: Failure to
properly secure the quick-release
lever may cause the T-bar to
telescope up or down while riding
which may cause you to lose
control and fall.
Note: The joint lever is springloaded and will automatically lock
in the upright position when fully
upright.
4 To adjust the height of the handlebars, open the quick-release lever and
slide the T-bar to the desired position and resecure the quick release lever to
lock into place. If the T-bar is raised to the maximum height, depress the push
button located directly below the quick release lever to lower the T-bar.
Note: The tension of the quickrelease lever can be adjusted by
tightening or loosening the Allen
bolt. Be careful not to over-tighten.
You should always be able to open
and close the quick-release lever
by hand and the T-bar should slide
freely with the quick-release open.
3
Set up and usage instructions
q Installing your chalk
WARNING: Keep fingers
clear of chalk bar hinge and fender
brake.
NOTE: Chalk is non-toxic.
Conforms to ASTM4236.
Chalk washes off with water for
easy clean-up.
1 Insert the tapered end of the
chalk into the spring.
2 Twist chalk clockwise 1/4 turn
until chalk is set securely in the
spring. Periodically turn chalk as
needed.
q How to Ride
Place one foot on the baseboard, push forward with the other foot. Steer. For enhanced cornering, lean slightly into the
direction of the turn. For controlled stops, apply the brake by stepping on the rear fender/brake. Razor recommends that
you practice applying the brake at various speeds and in an open area free from obstructions before riding your Razor
around others.
q Using the Chalk Bar
When riding, place ball of foot on the chalk bar and apply pressure until the chalking mechanism clicks into place. Only
use enough pressure to cause chalk to make a mark. To stop chalking, place ball of foot on chalk bar and apply pressure
until it clicks to the desired position.
1Up Position - No chalking
2
WARNING: Applying too
much pressure on the chalk bar may
cause loss of control.
NOTE: Using any other part of
the foot or full foot may activate the
brake and prevent the chalk action.
NOTE: Chalk marks and
chalk life will vary based
on the amount of pressure
applied to the chalk bar and
the smoothness of the riding
surface.
Down Position - Chalking
Need Help? Visit www.razor.com for replacement parts, product support and a list of authorized
service centers or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
4
Check before riding
q Collar Clamp
Using a 5mm Allen key, check that the collar clamp bolt is tightened securely. This part is tightened and quality
inspected at the factory but there is a slight chance that the effects of shipping or handling may have caused this bolt
to become loose.
q Wheels and Bearings
Under normal circumstances and conditions, Razor wheels and bearings are maintenance free. Nonetheless, it is
the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper
tightness, and bearings for side-to-side play and loose parts. When a wheel or wheel bearing develops play, this is an
indication of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels. Wheels
other than genuine Razor wheels may not be compatible with your Razor scooter. The use of anything other than genuine Razor replacement parts may affect your safety and will void your warranty.
WARNING: Wheelies
will break the chalk bar. Other
stunt-type riding reduces your
ability to maneuver and control
the scooter. Take the necessary
precautions, such as wearing
appropriate protective gear and
practice in a area safe for stunt
riding and free from obstructions.
NOTE: Worn wheels, bearings
and chalk cartridges are considered
normal wear-and-tear and are not
covered by the Razor Warranty.
q Cleaning Your Scooter
Wipe with a damp cloth to remove dirt and dust.
Do not use industrial cleaners or solvents as they may damage the surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners as they may damage or dissolve the plastic components or soften the decals or decal adhesive.
5
Scooter Parts List
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
1.
Foam Grips
12.
98mm Wheels
2.Handlebar
13.
Coupling Axle Screw
3.
T-Bar
14.
Deck Insert (front)
4.
Quick-Relese Lever
15.
Reinforce Plate
5.
Extension Tube
16.
Joint Release Lever
6.
Collar Clamp
17.
Folding Base
7.Headset
18.
Folding Protector
8.
19.Fender/Brake
Head Tube
9.Fork
20.
Chalk Bar
10.
Fork Protector
21.
Deck Insert (rear)
11.
Axle Bolt (front/rear)
1
2
3
4
5
16
17
18
6
20
7
19
8
21
9
10
23
11
15
11
14
12
13
12
13
Need Help? Visit www.razor.com for replacement parts, product support and a list of authorized
service centers or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
6
Safety reminders
PRE-RIDE CHECKLIST
q
Loose Parts
q
q
Replacement Parts
q
Check and secure all fasteners before every ride. Make sure the
collar clamp, quick release lever, and handlebar spring buttons are
locked properly in place before riding.
Replace worn or broken parts immediately. Call 1-866-GO-RAZOR
for parts.
Be Careful!
You will see people on TV and maybe even people you know doing
tricks and stunts. These are people who have been practicing on
scooters for a very long time. Don’t try something until you are
ready. Avoid steep inclines and don’t ride too fast — you can lose
control and fall. Skateboard parks are not designed for scooters.
Never ride in traffic or on the street and watch your surroundings
for pedestrians, bikers, boarders and skaters.
Maintain a hold on the handlebars at all times.
Safety Gear
Always wear proper protective equipment such as an approved
safety helmet, elbow pads and kneepads. Always wear shoes
(lace-up with rubber soles), never ride barefooted or in sandals,
and keep shoelaces tied and out of the way of the wheels.
DO NOT RETURN TO STORE
Failure to follow these instructions may damage
your product and void your warranty.
Warranty
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing defects
for a period of 6 months from date of purchase. This Limited Warranty does
not cover normal wear and tear, or any damage, failure or loss caused by
improper assembly, maintenance, or storage.
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation;
• modified in any way;
• rented.
__________________________________________
For your records, save your original sales receipt with this manual.
Item Number:
Black
Blue
Purple
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
13010800
13010840
13010850
Need Help? Visit www.razor.com for replacement parts, product support and a list of authorized
service centers or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
Copyright © 2003-2010 Razor USA, LLC. All rights reserved. RAZOR and the Razor Logo
Design are among the registered trademarks of Razor USA LLC in the United States and/or
select foreign countries. Graffitil is a trademark of Razor USA LLC.
09/2010
7
Download PDF
Similar pages