advertisement
®
1.9 4WD ELECTRIC SCALER RTR
ECX01009 | ECX01009I
Congratulations on your purchase of the ECX
®
Barrage
™
1.9 4WD Electric Scaler.
This model introduces you to the sport of RC driving.
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
Herzlichen Glückwunsch zum kauf des ECX Barrage 1.9 4WD Electric Scaler.
Dieses Modell ist der gelungende Einstieg in die Welt des RC Cars Sports.
Nous vous félicitons pour l’achat de l’ECX Barrage 1,9 4WD électrique. Ce modèle vous permettra de découvrir l’univers du RC.
Congratulazioni per l’acquisto dell’ECX Barrage 1.9 4WD Electric Electric Scaler.
Questo modello dà accesso al mondo degli automodelli radiocomandati.
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the receiver in the car.
Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio equipment.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine.
The various electronic components used in the vehicle, such as the
Electronic Speed Control (ESC) and servo(s) are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Do not use Li-Po batteries in wet conditions.
• The included transmitter is not waterproof or water-resistant. If using a different transmitter than the one included, consult your transmitter's manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.
2
Wet Conditions Maintenance
• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil or lubricant. Do not spray the motor.
• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.
EN
Transmitter
Frequency 2.4GHz
Battery AA x 4
Servo
Power Supply
Output Torque
Operating Speed
Size
4.8V~6V
5 oz (1.5 kg-cm)
0.15sec/60 degrees of travel
40 x 20.3 x 38mm
SPECIFICATIONS
Electronic Speed Control (ESC)
Input Voltage
Electric Capacity
PWM Frequency
BEC Voltage
Size
Weight
6.0–8.4V
60A ESC
1kHz
5V/2A
46.5 x 34 x 28.5mm
65 g
COMPONENTS
• ECX
®
Barrage
™
Scaler
• ECX
®
2.4GHz 2-CH V3 Transmitter
• AA (4) Batteries
• 100mAh NiMH Wall Charger with EC3™ Connector
• Dynamite ® Speedpack ® 900mAh NiMH battery with
EC3™ Connector
• Dynamite
®
Tazer™ 370 Brushed Motor
• Dynamite
®
60A WP FWD/REV Brushed ESC
• ECX
®
2.4GHz 2-CH V3 Receiver
• Spektrum™ Digital Servo (SPMS602)
TABLE OF CONTENTS
Quick Start....................................................................................................4
Vehicle Preparations ....................................................................................4
Charging the Vehicle Battery .......................................................................4
Charging Warnings ......................................................................................4
Installing the Battery....................................................................................5
Transmitter Controls .....................................................................................5
Installing Transmitter Batteries ...................................................................5
Binding .........................................................................................................6
Getting Started.............................................................................................6
Operation......................................................................................................7
When You Are Finished................................................................................7
Motor Care ...................................................................................................7
Maintenance ................................................................................................8
Setting the Gear Mesh.................................................................................8
Electronic Speed Control (ESC) ....................................................................8
Troubleshooting Guide .................................................................................9
Limited Warranty .......................................................................................10
Warranty and Service Contact Information ...............................................11
FCC Information..........................................................................................11
IC Information.............................................................................................11
Parts Diagram...................................................................................... 40–41
Replacement Parts .............................................................................. 42–43
Optional Parts.............................................................................................43
3
EN
QUICK START
Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance.
1. Read the safety precautions found in this manual.
2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information.
3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries.
4. Install the fully charged battery in the vehicle.
5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.
VEHICLE PREPARATIONS
CHARGING THE VEHICLE BATTERY
NOTICE: Never charge a battery in the vehicle or damage may result.
CHARGING WARNINGS
WARNING: Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.
1. Connect the NiMH battery to the battery charger.
2. Connect the charger to an AC power outlet.
3. Allow the NiMH battery to charge for 9 hours.
• NEVER LEAVE CHARGING BATTERIES UNATTENDED.
• NEVER CHARGE BATTERIES OVERNIGHT.
• Read all safety precautions and literature prior to use of this product.
• Never leave the battery and charger unattended during use.
• Never allow children under 14 years of age to charge battery packs.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
• Never allow batteries or charger to come into contact with moisture at any time.
• Never charge batteries in extremely hot or cold places (recommended between 50–80°F (10–26°C)) or place in direct sunlight.
• Always use only Ni-MH rechargeable batteries. This charger cannot charge batteries such as “heavy duty,” “alkaline,” “mercury” or
“lithium” battery.
• Always connect to the charger correctly.
• Always disconnect the battery and charger after charging and let them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the product malfunctions.
• Always make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger.
• Always constantly monitor the temperature of the battery pack while charging.
• Always end the charging process if the charger or battery becomes hot to the touch or starts to change form during the charge process.
• Always charge in a well ventilated area.
4
INSTALLING THE BATTERY
1. Remove the vehicle body.
2. Install a fully charged battery.
3. Secure the battery pack using the hook and loop straps.
4. Connect the battery pack to the ESC power connector.
CAUTION: Connecting the battery to the ESC with reversed polarity will cause damage to the ESC, the battery or both. Damage caused by incorrectly connecting the battery is not covered under warranty.
TRANSMITTER CONTROLS
BATTERY LEVEL INDICATOR
Solid Red and Green:
Battery voltage is good
(above 4V).
Solid Red: Battery voltage is critically low (below
4V). Replace transmitter batteries.
THROTTLE DUAL RATE
Adjusts the maximum amount of throttle the vehicle can be given
STEERING DUAL RATE
Adjusts the amount the steering moves when the steering wheel is turned left or right
REVERSE SWITCH
Allows you to change the direction of steering (ST.
REV) and throttle (TH. REV) controls (Ensure proper function with a radio system test).
POWER SWITCH
Power on or off the transmitter
STEERING WHEEL
THROTTLE TRIM
Adjusts the neutral point of the electronic speed control
Control steering.
Right and Left steering
THROTTLE TRIGGER
STEERING TRIM
Adjust to make the vehicle drive straight with no input at the steering wheel
Reverse
Controls power to the motor for forward or reverse
Forward
Stop
INSTALLING TRANSMITTER BATTERIES
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.
5
EN
EN
BINDING
The included transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below.
1. Power off the transmitter and ESC.
2. Connect a fully charged battery pack to the ESC.
3. Power on the ESC. The RED LED on the receiver flashes.
4. Press and release the bind button (A) on the receiver.
The RED LED on the receiver flashes rapidly.
5. Power on the transmitter.
6. The RED LED on the receiver turns solid when the radio system is bound.
You must rebind when binding the receiver to a different transmitter.
A
NOTICE: Do not attempt to bind the transmitter and receiver if there are other compatible transmitters in bind mode within 400 feet. Doing so may result in unexpected binding.
GETTING STARTED
1. Power on the transmitter.
2. Connect the battery to the Electronic Speed Control
(ESC) / Receiver unit and power on the vehicle .
3. Perform a test of the transmitter’s control of the vehicle with the vehicle’s wheels off the ground.
4. Start driving slowly, and, if the vehicle does not go straight, adjust the steering trim dial on the transmitter.
IMPORTANT: Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Properly seating the motor brushes will increase the life and performance of the motor.
6
OPERATION
• ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off.
• ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result.
EN
1. Power off the ESC.
WHEN YOU ARE FINISHED
2. Disconnect the battery.
3. Power off the transmitter.
4. Remove the battery from the vehicle.
5. Recharge the battery.
MOTOR CARE
• Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Failing to do so can greatly
reduce motor performance and functional life.
• Prolong motor life by preventing overheating conditions.
Undue motor wear results from frequent turns, stops and starts, pushing objects, driving in deep water and tall grass, and driving continuously up hill. Allow the motor to cool completely
before running the vehicle.
• Over-temperature protection is installed on the ESC to prevent circuit damage, but cannot protect the motor from driving against heavy resistance.
7
EN
MAINTENANCE
SETTING THE GEAR MESH
The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears.
You must remove the vehicle’s gear cover (A) to make this adjustment.
Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat.
Set the gear mesh by following these simple steps:
1. Loosen the 2 motor screws (B).
2. Put a small piece of paper (C) between the pinion and spur gears.
3. Push the gears together while tightening the motor screws.
B
C
A
4. Rotate the gears to remove the paper. The gearing should move a small amount.
5. Reinstall the gear cover.
ELECTRONIC SPEED CONTROL (ESC)
Connecting
1. Connect the RED (+) ESC wire to the RED (+) motor wire.
2. Connect the BLACK (–) ESC wire to the BLACK (–) motor wire.
NOTICE: Always disconnect the battery from the ESC when you have finished operating your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC will continue to draw current when connected to the battery, resulting in possible damage to the battery through over-discharge.
Calibrating
Ensure proper ESC function by calibrating the ESC to your transmitter inputs.
1. Power OFF the ESC.
2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral and the throttle travel range is at 100%.
3. Keep the throttle at neutral and power ON the ESC.
4. The ESC automatically calibrates the throttle range after 3 seconds.
5. One long beep will sound when the ESC is ready to run.
Programming
The ESC comes with two jumpers pre-installed in the MODE: Forward/
Brake/Reverse) and BATT: Ni-MH configurations.
To change the mode to F/B/R (forward/brake/reverse) or F/R (forward/ reverse) or change the battery type to Li-Po:
1. Power OFF the ESC.
2. Disconnect the jumper from the default port and connect it to the desired port.
3. Power ON the ESC.
If the jumpers are lost or not installed, the ESC will default to MODE:
F/B/R and BATT: Li-Po.
WARNING: Do not connect bind plugs or receiver servo leads into the ESC programming port. Doing so may damge the ESC and/or components.
Mode
Battery
(BATT)
Forward/
Brake/
Reverse
(F/B/R)
Forward/
Brake
(F/B)
Li-Po Ni-MH
Forward/
Reverse
(F/R ((Crawler
Mode))
8
TROUBLESHOOTING GUIDE
Problem
Short Run Time
Sluggish Action
Controls Reversed
Motor/ESC overheat
Does Not Operate
Poor Range
The system will not connect
Possible Cause
Battery damaged/not charged
Motor dirty
Motor dirty
Bind in drivetrain
Vehicle battery is not charged
ST. REV or TH. REV
Over-geared for the driving environment
Transmitter batteries low
Transmitter powered off
ESC powered off
Vehicle battery is not charged
Dual-rate (D/R) steering and/or throttle knobs on transmitter are turned to zero
Transmitter batteries low
Receiver antenna damaged
Transmitter and receiver too near each other
Transmitter and receiver too near large metal objects (vehicles, etc.)
Throttle trim out of center on transmitter
Solution
Check/change battery
Check/clean
Check/clean
Clean/adjust
Replace/recharge
Change switch position
Install smaller pinion on the motor
Replace/recharge
Power on
Power on
Replace/recharge
Adjust dual-rate (D/R) steering and/or throttle knobs to 10
Replace/recharge
Check/repair/replace
Move transmitter 3.3–9.8ft (1–3m) from receiver
Move away from large metal objects (vehicles, etc.)
Set throttle trim on transmitter to zero. Turn off and on transmitter and vehicle
Rebind transmitter and receiver
Receiver accidentally put in bind mode so receiver is no longer bound
The receiver goes into failsafe mode a short distance away from the transmitter
Check the receiver antenna to be sure it is not cut or damaged
The receiver quits responding during operation
Receiver and transmitter are not bound
Vehicle moves forward or backward without input from user
Car does not drive straight
Low battery voltage
Loose or damaged wires or connectors between battery and receiver
Transmitter accidentally put in bind mode, ending bind to receiver
Throttle trim on transmitter not centered
Steering trim on transmitter not centered
No steering or lack of steering
Steering dual-rate (D/R) not adjusted correctly
Servo failed
No throttle or lack of throttle
Clicking noise in transmission area
Throttle dual-rate (D/R) not adjusted correctly
ESC failed
Motor failed
Dirt or rocks in spur gear
Motor moved away from spur gear
Make sure the antenna is in the antenna tube
Contact Horizon Product Support
Completely recharge battery
Do a check of the wires and connection between battery and receiver. Repair or replace wires and/or connectors
Bind transmitter to receiver
Adjust throttle trim to set neutral point
Adjust steering trim so vehicle drives straight
Adjusts steering dual-rate (D/R) knob on transmitter to desired steering throw
Contact Horizon Product Support
Adjust the throttle dual-rate (D/R) knob on transmitter to desired steering throw
Contact Horizon Product Support
Contact Horizon Product Support
Remove gear cover and inspect. If necessary, replace gear
Reset gear mesh
EN
9
EN
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase. that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service
Contact Information section to speak with a Product Support representative.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE
IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.
horizonhobby.com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a
RMA number along with instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration.
Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon
Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales
receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM
IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the
retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant
Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced
Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
10/15
10
WARRANTY AND SERVICE CONTACT INFORMATION
Country of
Purchase
Horizon Hobby Contact Information
United States of America
Horizon Service Center
(Repairs and Repair Requests)
Horizon Product Support
(Product Technical Assistance) servicecenter.horizonhobby.com/
RequestForm/ [email protected]
United Kingdom
Sales
Service/Parts/Sales:
Horizon Hobby Limited
877-504-0233 [email protected]
800-338-4639 [email protected]
+44 (0) 1279 641 097
Germany
France
Horizon Technischer Service
Sales: Horizon Hobby GmbH
Service/Parts/Sales:
Horizon Hobby SAS [email protected]
+49 (0) 4121 2655 100 [email protected]
+33 (0) 1 60 18 34 90
Address
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
Christian-Junge-Straße 1
25337 Elmshorn, Germany
11 Rue Georges Charpak
77127 Lieusaint, France
EN
FCC INFORMATION
FCC Number: BRWECX13002 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your Spektrum transmitter, please be sure to maintain a separation distance of at least 5 cm between your body
(excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
The following illustrations show the approximate 5 cm RF exposure area and typical hand placement when operating your Spektrum transmitter.
IC INFORMATION
IC Number: 6157A-ECX13002 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the R&TTE, EMC, and LVD
Directives.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
11
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
ECX212026
ECX212009
ECX212026
ECX212010
40
ECX212010
ECX214011
ECX211019
ECX211014
ECX213002
ECX211016
ECX214013
ECX211018
ECX211015
ECX211018
ECX211020
ECX211020
ECX211019
ECX211017
ECX211018
ECX211015
ECX212025
ECX213002
ECX214012
ECX211019
ECX211018
ECX211014
ECX212028
ECX212025
ECX212025
ECX212027
ECX212024
ECX1015
ECX212020
ECX211016
ECX212024
ECX312005
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
ECX212019
ECX212020
DYNS1209
ECX212021
ECX211021
ECX211009
DYNS2210
SPMS602
ECX211021
ECX13003
ECX211021
SPMS602
ECX210011 - Painted / painted / peinte / verniciata
ECX210010 - Clear / transparent / transparente / trasparente
ECX41006
ECX41004
41
ECX211014
ECX211015
ECX211016
ECX211017
ECX211018
ECX211019
ECX211020
ECX211021
ECX212009
ECX212010
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Part #
DYNS1209
DYNS2210
ECX1015
ECX13002
ECX13003
Description
Tazer 370 motor
Beschreibung
Motor: Tazer 370
WP 60A Bürstenregler
Vorwärts/rückwärts
WP 60A FWD/REV Brushed
ESC
5x10x4mm Ball Bearing (8) Kugellager 5x10x4mm (8)
2.4GHz Surface TX, 2-CH, V3 2.4GHz 2 Kanal Sender V3
2.4GHz RX Waterproof,
2-Channel V3
2.4GHz 2 Kanal Empfänger wasserfesten V3
Description
Moteur: Tazer 370
WP 60A Contrôleur à balais avant/ arrière
Roulements 5x10x4mm (8)
2.4GHz Emetteur 2 voies, V3
2.4GHz Récepteur étanche 2 voies
V3
Descrizione
Motore: Tazer 370
WP 60A ESC con spazzole avanti/ indietro
Cuscinetto a sfere 5x10x4mm (8)
2-Ch trasmettitore, V3
2.4GHz ricevitore impermeabile
2Ch, V3
ECX210011
ECX211009
ECX212012
ECX212018
ECX212019
ECX212020
ECX212021
ECX212022
ECX212023
ECX212024
ECX212025
ECX212026
ECX212027
ECX212028
ECX213002
ECX214010
ECX214011
1.9 Barrage Carrosserie peinte Carrozzeria, verniciata: 1.9 Barrage
Servo Mount: 1/18 4WD
Temper
Front/Rear Bumper Set: 1.9
Barrage
Servohalter: 1/18 4WD
Temper
Stoßfänger Vorne/Hinten: 1.9
Barrage
1/18 4WD Temper: Support de servo Supporto servo: 1/18 4WD Temper
1.9 Barrage: Set de pare-choc Av/Arr Set paraurti ant/post: 1.9 Barrage
Bumper Mount: 1.9 Barrage Stoßfängerhalter: 1.9 Barrage 1.9 Barrage: Support de pare-choc Supporto paraurti: 1.9 Barrage
Chassis Set: 1.9 Barrage Chassis: 1.9 Barrage 1.9 Barrage: Châssis Set telaio: 1.9 Barrage
Skid Plate: 1.9 Barrage
Shock Tower: 1.9 Barrage
Unterfahrschutz: 1.9 Barrage
Dämpferbrücke: 1.9 Barrage
1.9 Barrage: Plaques de protection
1.9 Barrage: Support d’amortisseurs
Piastra di protezione: 1.9 Barrage
Torre ammortizz.: 1.9 Barrage
Body Post: 1.9 Barrage Karosseriehalter: 1.9 Barrage 1.9 Barrage: Supports de carrosserie Supporti carrozzeria: 1.9 Barrage
Chassis Brace (2): 1.9 Barrage Chassishalter (2): 1.9 Barrage 1.9 Barrage: Renforts de châssis (2) Rinforzo telaio (2): 1.9 Barrage
ESC & Battery Tray: 1.9
Barrage
Regler und akkuhalter: 1.9
Barrage
1.9 Barrage: Support de batterie et contrôleur
Spool 38T: 1/18 4WD Temper Spool 38T: 1/18 4WD Temper 1/18 4WD Temper: Spool 38T
Supporto batteria e ESC: 1.9
Barrage
Corona 38T: 1/18 4WD Temper
Axle Pinion Gear 14T: 1/18
4WD Temper
Transmission Assembled: 1/18
4WD Temper
Spur Gear 48P 60T(1): 1/18
4WD Temper
Pinion Gear, 48P 16T: 1.9
Barrage
Transmission Outdrive: 1.9
Barrage
Driveshaft (2): 1.9 Barrage
Rear Hub (2): 1.9 Barrage
Rear Axle (2): 1.9 Barrage
Ritzel 14T: 1/18 4WD Temper
Abtrieb montiert: 1/18 4WD
Temper
Hauptzahnrad 48P 60T(1): 1/18
4WD Temper
Ritzel, 48P 16T: 1.9 Barrage
Anriebsklauen: 1.9 Barrage
Radträger Hinten (2): 1.9
Barrage
Radachse hinten (2): 1.9
Barrage
1/18 4WD Temper: Pignon 14T
1/18 4WD Temper: Transmission assembleés
1/18 4WD Temper: Couronne 48P
60T(1)
1.9 Barrage: Pignon, 48P 16T
1.9 Barrage: Noix de sortie de transmission
Antriebswelle (2): 1.9 Barrage 1.9 Barrage: Cardan (2)
1.9 Barrage: Fusée arrière (2)
1.9 Barrage: Axe de roue arrière (2)
Pignone 14T: 1/18 4WD Temper
Trasmissione montati: 1/18 4WD
Temper
Corona 48P 60T(1): 1/18 4WD
Temper
Pignone, 48P 16T: 1.9 Barrage
Bicchierini transmissione: 1.9
Barrage
Albero trasmissione (2): 1.9 Barrage
Mozzo posteriore (2): 1.9 Barrage
Front CV Shaft, Set (2): 1.9
Barrage
Front/Rear Diff Case V2: 1.9
Barrage
Steering Spindle V2: 1.9
Barrage
Front/Rear Hub Set, V2: 1.9
Barrage
CV Wellen Set Vorne (2): 1.9
Barrage
Diffgehäuse Vorne/Hinten V2:
1.9 Barrage
Lenkspindel V2: 1.9 Barrage
1.9 Barrage: Hexagone 12mm, large
1.9 Barrage: Set de cardans CVD avant (2)
1.9 Barrage: Boitiers de différentiel
Av/Arr V2
1.9 Barrage: Set de fusées V2
1.9 Barrage: Set d’étriers Av/Arr, V2
Mozzi ruota posteriori (2): 1.9
Barrage
Trascinatore 12 mm, largo: 1.9
Barrage
Set alberi CV anteriore (2): 1.9
Barrage
Scatola diffeenziale ant/post V2:
1.9 Barrage
Fusello sterzo V2: 1.9 Barrage
Set hub ant/post, V2: 1.9 Barrage
F/R Shocks Assembled (2): 1.9
Barrage
Molded Link (2): 1/18 4WD
Temper
Träger Set Vorne/Hinten, V2:
1.9 Barrage
Dämpfer montiert Vorne/
Hinten (2): 1.9 Barrage
Anlenkungen welle (2): 1/18
4WD Temper
Servo Linkage (2): 1.9 Barrage Servoarm (2): 1.9 Barrage
1.9 Barrage: Amortisseurs Av/Arr assemblés (2)
Biellette moulé (2): 1/18 4WD
Temper
1.9 Barrage - Biellette (2)
Ammortizzatori montati ant/post
(2): 1.9 Barrage
Collegamento stampato (2): 1/18
4WD Temper
Collegamento servo (2): 1.9
Barrage
42
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Part # Description Beschreibung Description
ECX214012
ECX214013
ECX217001
Lower Link (2): 1.9 Barrage
Upper Link (2): 1.9 Barrage
Unterlenker (2): 1.9 Barrage
Oberlenker (2): 1.9 Barrage
1.9 Barrage: Tirant inférieur (2)
1.9 Barrage: Tirant supérieur (2)
1/18 4WD - Set de roulements de fusées
Descrizione
Collegamento inferiore (2): 1.9
Barrage
Collegamento superiore (2): 1.9
Barrage
Set supporto fusello/hub: 1/18
4WD All
ECX41004
ECX41006
SPMS602
Spindle/Hub Bearing Set: 1/18
4WD All
1.9 Wheel Black (2): 1.9
Barrage
1.9 Falken Wildpeak AT3 W
Tire (2)
SCT2 Digital Servo
ECX Spindelset/Lagerset:
1/18 4WD All
1.9 radkranz schwarz (2): 1.9
Barrage
Reifen 1.9 Falken Wildpeak
AT3 W (2)
SCT2 Digital Servo
1.9 Barrage - Jante 1,9 noire (2)
Servo digital SCT2
Ruota (2) 1.9 nera: 1.9 Barrage
SCT2 Digital Servo
Optional Parts / Optionale Teile / Liste des options / Elenco parti opzionali
Part #
DYN1471
Description
7.2V 1750mAh NiMH 6C Flat
Battery, EC3: Minis
Beschreibung
Flache Akkus Ni-MH 7,2V
1750mA, EC3: Mini 1/18
DYN1473
DYNC2000CA Prophet Sport NiMH 35W AC
Charger
ECX210010
7.2V 1200mAh Ni-MH Battery,
Long w/EC3: Minis
Body Set, Clear: 1.9 Barrage
Lange Akkus Ni-MH 7,2V
1750mA, EC3: Mini 1/18
Prophet Sport NiMH 35W
AC-Ladegerät
Body Set, transparent: 1.9
Barrage
ECX312005
ECX41005
Rear Hub Carrier, Alum: 1.9
Barrage
1.9 Wheel (2) White: 1.9
Barrage
Rädträger hinten, Alum: 1.9
Barrage
1.9 radkranz weiß (2): 1.9
Barrage
Description
Mini 1/18: Batterie plate Ni-MH
7,2V 1750mA, prise EC3
Mini 1/18: Batterie longue Ni-MH
7,2V 1200mA, prise EC3
Chargeur Prophet Sport AC Ni-MH
35W
1.9 Barrage: Carrosserie, transparente
1.9 Barrage: Set d’étriers arrière, aluminium
1.9 Barrage: Jante 1,9 blanche (2)
Descrizione
Batteria piatta 6C NiMH 1750 mAh 7,2 V, EC3: Minis
Batteria lunga NiMH 1200 mAh
7,2 V c/EC3: Minis
Caricabatteria AC Prophet Sport
NiMH 35 W
Carrozzeria trasparente: 1.9
Barriage
Supporto hub posteriore, allum.:
1.9 Barrage
Ruota (2) 1.9 bianca: 1.9 Barrage
43
®
ECX01009 | ECX01009I www.ecxrc.com
© 2016 Horizon Hobby, LLC. ECX, the ECX logo, Barrage, Dynamite, Speedpack, Prophet, Tazer, EC3, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc. Patents Pending.
Created 08/2016 52321
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Quick Start
- 4 Vehicle Preparations
- 4 Charging the Vehicle Battery
- 4 Charging Warnings
- 5 Installing the Battery
- 5 Transmitter Controls
- 5 Installing Transmitter Batteries
- 6 Binding
- 6 Getting Started
- 7 Operation
- 7 When You Are Finished
- 7 Motor Care
- 8 Maintenance
- 8 Setting the Gear Mesh
- 8 Electronic Speed Control (ESC)
- 9 Troubleshooting Guide
- 10 Limited Warranty
- 11 Warranty and Service Contact Information
- 11 FCC Information
- 11 IC Information
- 13 Parts Diagram
- 15 Replacement Parts
- 15 Optional Parts