BS8060 Piranha
Pocket Bluetooth Barcode Scanner
User Guide
Disclaimer
© 2016-2017 Fujian Newland Auto-ID Tech. Co., Ltd. All rights reserved.
Please read through the manual carefully before using the product and operate it according to the manual. It
is advised that you should keep this manual for future reference.
Do not disassemble the device or remove the seal label from the device, doing so will void the product
warranty provided by Fujian Newland Auto-ID Tech. Co., Ltd.
All pictures in this manual are for reference only and actual product may differ. Regarding to the product
modification and update, Fujian Newland Auto-ID Tech. Co., Ltd. reserves the right to make changes to any
software or hardware to improve reliability, function, or design at any time without notice. The information
contained herein is subject to change without prior notice.
The products depicted in this manual may include software copyrighted by Fujian Newland Auto-ID Tech. Co.,
Ltd or third party. The user, corporation or individual, shall not duplicate, in whole or in part, distribute, modify,
decompile, disassemble, decode, reverse engineer, rent, transfer or sublicense such software without prior
written consent from the copyright holders.
This manual is copyrighted. No part of this publication may be reproduced, distributed or used in any form
without written permission from Newland.
Fujian Newland Auto-ID Tech. Co., Ltd. reserves the right to make final interpretation of the statement above.
Fujian Newland Auto-ID Tech. Co., Ltd.
3F, Building A, No.1, Rujiang West Rd., Mawei, Fuzhou, Fujian, China
http://www.newlandaidc.com
350015
Revision History
Version
Description
Date
V1.0
Initial release.
March 18, 2015
V1.1
Added the content concerning the 2D version.
May 19, 2015
V1.2
V1.3
1. Added the Enable/Disable USB HID-KBW feature in Chapter 2.
2. Added barcode parameters in Chapter 3.
Added the USB country keyboard types in Chapter 2.
Note: Firmware version V1.00.006 or later is required for the new feature above.
September 16, 2015
October 13, 2015
1. Added Chapter 4 Prefix & Suffix.
V1.4
2. Added the “Code ID Table (1D Scanner)” and “Code ID Table (2D
Scanner)” sections in Appendix.
January 21, 2016
Note: Firmware version V1.00.011 or later is required for the new feature above.
V1.4.1
Updated the programming barcodes in the “Digit Barcodes (1D
Scanner)” and “Save/Cancel Barcodes (1D Scanner)” sections in
Appendix.
May 5, 2016
V2.0.0
User Guide V2.0.0 or higher is written for the NLS-BS8060 only.
September 26, 2016
1. Modified the description of the Product Serial Number and Time
Stamp features in Chapter 2.
V2.0.1
2. Added the EAN-13 Beginning with 290 Add-On Code Required,
EAN-13 Beginning with 378/379 Add-On Code Required, EAN-13
Beginning with 414/419 Add-On Code Required, EAN-13
Beginning with 434/439 Add-On Code Required, EAN-13
Beginning with 977 Add-On Code Required, EAN-13 Beginning
with 978 Add-On Code Required, EAN-13 Beginning with 979
Add-On Code Required, Code 32 (Italian Pharma Code), Code 32
Prefix, Transmit Code 32 Check Character and Transmit Code 32
Start/Stop Character features for 1D & 2D scanners in Chapter 3.
November 28, 2016
3. Changed the default settings of the following parameter to:
Time Stamp
Disabled
Note: Firmware version V3.00.002 or later is required for the new features above.
V2.0.2
1. Added the 0ms option for the Inter-Character Delay for Bluetooth
HID feature in Chapter 2.
2. Modified the firmware upgrade procedure in Chapter 2.
Note: Firmware version V3.00.004 or later is required for the new feature above.
February 14, 2017
1. Added the Bluetooth Device Name, Barcode Separator, Packet
Mode, ACK/NAK Retry Count and ACK/NAK Timeout features, and
modified the Inter-Keystroke Delay for KBW options in Chapter 2.
2. Added Chapter 6 Data Formatter.
V2.1.0
3. Modified the “Factory Defaults Table”, and added the “Digit
Barcodes”, “Save/Cancel Barcodes” and “Symbology ID Number”
sections in Appendix.
4. Modified the “Parameters of USB HID-KBW/ Bluetooth HID” section
in Chapter 2.
Note: Firmware version BS80+_V3.00.005 or later is required for the new features
above. For the Data Formatter feature, scan engine firmware version
EM1300_BS80_V1.00.000/ EM3396_BS80_V1.00.001 or later is also required.
October 11, 2017
Table of Contents
Revision History ........................................................................................................................................ - 3 Preface ........................................................................................................................................................... 1
Introduction ............................................................................................................................................... 1
Chapter Descriptions ................................................................................................................................. 1
Safety Instructions ..................................................................................................................................... 2
Chapter 1 Getting Started ............................................................................................................................. 3
Introduction ............................................................................................................................................... 3
Unpacking ................................................................................................................................................. 3
BS80 Scanner ........................................................................................................................................... 4
Button Functions ....................................................................................................................................... 5
Charging the Battery ................................................................................................................................. 6
Connecting the BS80 to Smartphone/Tablet ............................................................................................. 7
LED Notifications ....................................................................................................................................... 9
Turning the BS80 On/Off ......................................................................................................................... 10
Scanning Instructions .............................................................................................................................. 11
Scanning 1D Barcode ....................................................................................................................... 11
Scanning 2D Barcode ....................................................................................................................... 11
Chapter 2 System Settings ......................................................................................................................... 12
Introduction ............................................................................................................................................. 12
Restore Factory Defaults......................................................................................................................... 12
Operating Modes ..................................................................................................................................... 12
Bluetooth Mode ................................................................................................................................. 13
USB Mode ......................................................................................................................................... 15
Query Product Information ...................................................................................................................... 17
Query/Delete Stored Data in Flash ......................................................................................................... 17
Sound Notifications ................................................................................................................................. 18
Vibration Notifications.............................................................................................................................. 19
Delete Bluetooth Pairing.......................................................................................................................... 19
Automatic/Manual Power-Off .................................................................................................................. 20
Bluetooth Device Name........................................................................................................................... 21
Barcode Separator .................................................................................................................................. 22
Packet Mode ........................................................................................................................................... 23
NAK/ACK Retry Count ...................................................................................................................... 24
NAK/ACK Timeout............................................................................................................................. 24
Product Serial Number ............................................................................................................................ 25
Time Stamp ............................................................................................................................................. 25
Set Date Format ................................................................................................................................ 25
Set Date & Time ................................................................................................................................ 26
Parameters of USB HID-KBW/ Bluetooth HID......................................................................................... 27
Keyboard Types ................................................................................................................................ 27
Character Encoding .......................................................................................................................... 30
Convert Case .................................................................................................................................... 30
Emulate ALT+Keypad........................................................................................................................ 31
Function Key Mapping ...................................................................................................................... 32
Emulate Numeric Keypad ................................................................................................................. 32
Code Page ........................................................................................................................................ 33
Inter-Character Delay for Bluetooth HID ........................................................................................... 34
Inter-Keystroke Delay for USB HID-KBW .......................................................................................... 35
Upgrading BS80 Firmware ...................................................................................................................... 37
Upgrading System Firmware ............................................................................................................. 37
Upgrading Scan Engine Firmware .................................................................................................... 40
Chapter 3 Symbologies............................................................................................................................... 42
Introduction ............................................................................................................................................. 42
1D Scanner ............................................................................................................................................. 42
Enable/Disable All Symbologies ........................................................................................................ 42
Code 128 .......................................................................................................................................... 43
Restore Factory Defaults ........................................................................................................... 43
Enable/Disable Code 128 .......................................................................................................... 43
Set Length Range for Code 128 ................................................................................................ 44
UCC/EAN-128 ................................................................................................................................... 45
Restore Factory Defaults ........................................................................................................... 45
Enable/Disable UCC/EAN-128................................................................................................... 45
Set Length Range for UCC/EAN-128 ......................................................................................... 46
AIM 128 ............................................................................................................................................. 47
Restore Factory Defaults ........................................................................................................... 47
Enable/Disable AIM 128 ............................................................................................................. 47
Set Length Range for AIM 128 ................................................................................................... 48
EAN-8 ............................................................................................................................................... 49
Restore Factory Defaults ........................................................................................................... 49
Enable/Disable EAN-8 ............................................................................................................... 49
2-Digit Add-On Code .................................................................................................................. 50
5-Digit Add-On Code .................................................................................................................. 51
EAN-8 Extension........................................................................................................................ 52
Transmit Check Character ........................................................................................................... 52
EAN-13 ............................................................................................................................................. 53
Restore Factory Defaults ........................................................................................................... 53
Enable/Disable EAN-13 ............................................................................................................. 53
Transmit Check Character ......................................................................................................... 53
2-Digit Add-On Code .................................................................................................................. 54
5-Digit Add-On Code .................................................................................................................. 55
EAN-13 Beginning with 290 Add-On Code Required ................................................................. 56
EAN-13 Beginning with 378/379 Add-On Code Required .......................................................... 56
EAN-13 Beginning with 414/419 Add-On Code Required .......................................................... 57
EAN-13 Beginning with 434/439 Add-On Code Required .......................................................... 57
EAN-13 Beginning with 977 Add-On Code Required ................................................................. 58
EAN-13 Beginning with 978 Add-On Code Required ................................................................. 58
EAN-13 Beginning with 979 Add-On Code Required ................................................................. 59
ISSN.................................................................................................................................................. 60
Restore Factory Defaults ........................................................................................................... 60
Enable/Disable ISSN ................................................................................................................. 60
ISBN.................................................................................................................................................. 61
Restore Factory Defaults ........................................................................................................... 61
Enable/Disable ISBN ................................................................................................................. 61
Set ISBN Format ........................................................................................................................ 61
UPC-E ............................................................................................................................................... 62
Restore Factory Defaults ........................................................................................................... 62
Enable/Disable UPC-E ............................................................................................................... 62
Transmit Check Character ......................................................................................................... 62
2-Digit Add-On Code .................................................................................................................. 63
5-Digit Add-On Code .................................................................................................................. 64
Transmit Preamble Character .................................................................................................... 65
UPC-E Extension ....................................................................................................................... 65
UPC-A ............................................................................................................................................... 66
Restore Factory Defaults ........................................................................................................... 66
Enable/Disable UPC-A ............................................................................................................... 66
Transmit Check Character ......................................................................................................... 66
Transmit Preamble Character .................................................................................................... 67
2-Digit Add-On Code .................................................................................................................. 68
5-Digit Add-On Code .................................................................................................................. 69
Interleaved 2 of 5 .............................................................................................................................. 70
Restore Factory Defaults ........................................................................................................... 70
Enable/Disable Interleaved 2 of 5 .............................................................................................. 70
Check Character Verification...................................................................................................... 70
Set Length Range for Interleaved 2 of 5 .................................................................................... 71
ITF-6 ................................................................................................................................................. 72
ITF-14 ............................................................................................................................................... 73
Deutsche 14 ...................................................................................................................................... 74
Restore Factory Defaults ........................................................................................................... 74
Enable/Disable Deutsche 14 ...................................................................................................... 74
Deutsche 12 ...................................................................................................................................... 75
Restore Factory Defaults ........................................................................................................... 75
Enable/Disable Deutsche 12 ...................................................................................................... 75
COOP 25 (Japanese Matrix 2 of 5) ................................................................................................... 76
Restore Factory Defaults ........................................................................................................... 76
Enable/Disable COOP 25 .......................................................................................................... 76
Check Character Verification...................................................................................................... 76
Set Length Range for COOP 25 ................................................................................................ 77
Matrix 2 of 5 (European Matrix 2 of 5) ............................................................................................... 78
Restore Factory Defaults ........................................................................................................... 78
Enable/Disable Matrix 2 of 5 ...................................................................................................... 78
Check Character Verification...................................................................................................... 78
Set Length Range for Matrix 2 of 5 ............................................................................................ 79
Industrial 25 ...................................................................................................................................... 80
Restore Factory Defaults ........................................................................................................... 80
Enable/Disable Industrial 25 ...................................................................................................... 80
Check Character Verification...................................................................................................... 80
Set Length Range for Industrial 25 ............................................................................................ 81
Standard 25 ...................................................................................................................................... 82
Restore Factory Defaults ........................................................................................................... 82
Enable/Disable Standard 25 ...................................................................................................... 82
Check Character Verification...................................................................................................... 82
Set Length Range for Standard 25 ............................................................................................ 83
Code 39 ............................................................................................................................................ 84
Restore Factory Defaults ........................................................................................................... 84
Enable/Disable Code 39 ............................................................................................................ 84
Check Character Verification...................................................................................................... 84
Transmit Start/Stop Character.................................................................................................... 85
Enable/Disable Code 39 Full ASCII ........................................................................................... 85
Set Length Range for Code 39 .................................................................................................. 86
Enable/Disable Code 32 ............................................................................................................ 87
Code 32 Prefix ........................................................................................................................... 87
Transmit Code 32 Check Character ........................................................................................... 88
Transmit Code 32 Start/Stop Character ..................................................................................... 88
Codabar ............................................................................................................................................ 89
Restore Factory Defaults ........................................................................................................... 89
Enable/Disable Codabar ............................................................................................................ 89
Check Character Verification...................................................................................................... 89
Transmit Start/Stop Character.................................................................................................... 90
Set Length Range for Codabar .................................................................................................. 91
Code 93 ............................................................................................................................................ 92
Restore Factory Defaults ........................................................................................................... 92
Enable/Disable Code 93 ............................................................................................................ 92
Check Character Verification...................................................................................................... 92
Set Length Range for Code 93 .................................................................................................. 93
Code 11 ............................................................................................................................................. 94
Restore Factory Defaults ............................................................................................................. 94
Enable/Disable Code 11 .............................................................................................................. 94
Check Character Verification ....................................................................................................... 95
Set Length Range for Code 11 .................................................................................................... 96
Plessey ............................................................................................................................................. 97
Restore Factory Defaults ........................................................................................................... 97
Enable/Disable Plessey ............................................................................................................. 97
Check Character Verification...................................................................................................... 97
Set Length Range for Plessey ................................................................................................... 98
MSI-Plessey ...................................................................................................................................... 99
Restore Factory Defaults ........................................................................................................... 99
Enable/Disable MSI-Plessey ...................................................................................................... 99
Check Character Verification.................................................................................................... 100
Set Length Range for MSI-Plessey .......................................................................................... 101
GS1 Databar ................................................................................................................................... 102
Restore Factory Defaults ......................................................................................................... 102
Enable/Disable GS1 Databar ................................................................................................... 102
2D Scanner ........................................................................................................................................... 103
Global Settings ................................................................................................................................ 103
Enable/Disable All Symbologies............................................................................................... 103
Enable/Disable 1D Symbologies .............................................................................................. 103
Enable/Disable 2D Symbologies .............................................................................................. 103
Video Reverse ......................................................................................................................... 104
Code 128 ........................................................................................................................................ 105
Restore Factory Defaults ......................................................................................................... 105
Enable/Disable Code 128 ........................................................................................................ 105
Set Length Range for Code 128 .............................................................................................. 106
GS1-128 (UCC/EAN-128) ............................................................................................................... 107
Restore Factory Defaults ......................................................................................................... 107
Enable/Disable GS1-128 ......................................................................................................... 107
Set Length Range for GS1-128................................................................................................ 108
AIM-128 .......................................................................................................................................... 109
Restore Factory Defaults ......................................................................................................... 109
Enable/Disable AIM-128 .......................................................................................................... 109
Set Length Range for AIM-128..................................................................................................110
EAN-8 .............................................................................................................................................. 111
Restore Factory Defaults .......................................................................................................... 111
Enable/Disable EAN-8 .............................................................................................................. 111
Transmit Check Character ........................................................................................................ 111
Add-On Code ............................................................................................................................112
Add-On Code Required ............................................................................................................113
EAN-8 Extension.......................................................................................................................113
EAN-13 ............................................................................................................................................114
Restore Factory Defaults ..........................................................................................................114
Enable/Disable EAN-13 ............................................................................................................114
Transmit Check Character ........................................................................................................114
Add-On Code ............................................................................................................................115
Add-On Code Required ............................................................................................................115
EAN-13 Beginning with 290 Add-On Code Required (For BS8060-2T) ....................................116
EAN-13 Beginning with 378/379 Add-On Code Required (For BS8060-2T) .............................116
EAN-13 Beginning with 414/419 Add-On Code Required (For BS8060-2T) .............................117
EAN-13 Beginning with 434/439 Add-On Code Required (For BS8060-2T) .............................117
EAN-13 Beginning with 977 Add-On Code Required (For BS8060-2T) ....................................118
EAN-13 Beginning with 978 Add-On Code Required (For BS8060-2T) ....................................118
EAN-13 Beginning with 979 Add-On Code Required (For BS8060-2T) ....................................119
ISSN................................................................................................................................................ 120
Restore Factory Defaults ......................................................................................................... 120
Enable/Disable ISSN ............................................................................................................... 120
Add-On Code ........................................................................................................................... 121
Add-On Code Required ........................................................................................................... 121
ISBN................................................................................................................................................ 122
Restore Factory Default ........................................................................................................... 122
Enable/Disable ISBN ............................................................................................................... 122
Set ISBN Format ...................................................................................................................... 122
Add-On Code ........................................................................................................................... 123
Add-On Code Required ........................................................................................................... 123
UPC-E ............................................................................................................................................. 124
Restore Factory Defaults ......................................................................................................... 124
Enable/Disable UPC-E ............................................................................................................. 124
Transmit Check Character ....................................................................................................... 124
Add-On Code ........................................................................................................................... 125
Add-On Code Required ........................................................................................................... 125
Transmit System Character “0” ................................................................................................ 126
UPC-E Extension ..................................................................................................................... 126
UPC-A ............................................................................................................................................. 127
Restore Factory Defaults ......................................................................................................... 127
Enable/Disable UPC-A ............................................................................................................. 127
Transmit Check Character ....................................................................................................... 127
Add-On Code ........................................................................................................................... 128
Add-On Code Required ........................................................................................................... 128
Transmit Preamble Character .................................................................................................. 129
Interleaved 2 of 5 ............................................................................................................................ 130
Restore Factory Defaults ......................................................................................................... 130
Enable/Disable Interleaved 2 of 5 ............................................................................................ 130
Set Length Range for Interleaved 2 of 5 .................................................................................. 131
Check Character Verification.................................................................................................... 132
ITF-14 ............................................................................................................................................. 133
ITF-6 ............................................................................................................................................... 134
Matrix 2 of 5 .................................................................................................................................... 135
Restore Factory Defaults ......................................................................................................... 135
Enable/Disable Matrix 2 of 5 .................................................................................................... 135
Set Length Range for Matrix 2 of 5 .......................................................................................... 136
Check Character Verification.................................................................................................... 137
Industrial 2 of 5................................................................................................................................ 138
Restore Factory Defaults ......................................................................................................... 138
Enable/Disable Industrial 2 of 5 ............................................................................................... 138
Set Length Range for Industrial 2 of 5 ..................................................................................... 139
Check Character Verification.................................................................................................... 140
Standard 25 (IATA 2 of 5) ................................................................................................................ 141
Restore Factory Defaults ......................................................................................................... 141
Enable/Disable Standard 25 .................................................................................................... 141
Set Length Range for Standard 25 .......................................................................................... 142
Check Character Verification.................................................................................................... 143
Code 39 .......................................................................................................................................... 144
Restore Factory Defaults ......................................................................................................... 144
Enable/Disable Code 39 .......................................................................................................... 144
Transmit Start/Stop Character.................................................................................................. 144
Set Length Range for Code 39 ................................................................................................ 145
Check Character Verification.................................................................................................... 146
Enable/Disable Code 39 Full ASCII ......................................................................................... 146
Enable/Disable Code 32 (For BS8060-2T) .............................................................................. 146
Code 32 Prefix (For BS8060-2T) ............................................................................................. 147
Transmit Code 32 Check Character (For BS8060-2T) ............................................................. 147
Transmit Code 32 Start/Stop Character (For BS8060-2T) ....................................................... 147
Codabar .......................................................................................................................................... 148
Restore Factory Defaults ......................................................................................................... 148
Enable/Disable Codabar .......................................................................................................... 148
Set Length Range for Codabar ................................................................................................ 149
Check Character Verification.................................................................................................... 150
Transmit Start/Stop Character.................................................................................................. 150
Start/Stop Character Format .................................................................................................... 151
Code 93 .......................................................................................................................................... 152
Restore Factory Defaults ......................................................................................................... 152
Enable/Disable Code 93 .......................................................................................................... 152
Set Length Range for Code 93 ................................................................................................ 153
Check Character Verification.................................................................................................... 154
GS1-Databar (RSS) ........................................................................................................................ 155
Restore Factory Defaults ......................................................................................................... 155
Enable/Disable GS1 Databar ................................................................................................... 155
Transmit Application Identifier “01” ........................................................................................... 155
Code 11 ........................................................................................................................................... 156
Restore Factory Defaults ......................................................................................................... 156
Enable/Disable Code 11........................................................................................................... 156
Set Length Range for Code 11 ................................................................................................. 157
Transmit Check Character ....................................................................................................... 158
Check Character Verification.................................................................................................... 158
Plessey ........................................................................................................................................... 159
Restore Factory Defaults ......................................................................................................... 159
Enable/Disable Plessey ........................................................................................................... 159
Set Length Range for Plessey ................................................................................................. 160
Check Character Verification .................................................................................................. 161
MSI-Plessey .................................................................................................................................... 162
Restore Factory Defaults ......................................................................................................... 162
Enable/Disable MSI-Plessey .................................................................................................... 162
Set Length Range for MSI-Plessey .......................................................................................... 163
Transmit Check Character ....................................................................................................... 164
Check Character Verification.................................................................................................... 164
PDF 417 .......................................................................................................................................... 165
Restore Factory Defaults ......................................................................................................... 165
Enable/Disable PDF 417 .......................................................................................................... 165
Set Length Range for PDF 417 ................................................................................................ 166
PDF 417 Twin Code ................................................................................................................. 167
QR Code ......................................................................................................................................... 168
Restore Factory Defaults ......................................................................................................... 168
Enable/Disable QR Code ......................................................................................................... 168
Micro QR .................................................................................................................................. 168
Set Length Range for QR Code ............................................................................................... 169
QR Twin Code .......................................................................................................................... 170
Data Matrix ...................................................................................................................................... 171
Restore Factory Defaults ......................................................................................................... 171
Enable/Disable Data Matrix...................................................................................................... 171
Set Length Range for Data Matrix............................................................................................ 172
Rectangular Barcode ............................................................................................................... 173
Mirror Image............................................................................................................................. 173
Data Matrix Twin Code ............................................................................................................. 174
Chinese Sensible Code ................................................................................................................... 175
Restore Factory Defaults ......................................................................................................... 175
Enable/Disable Chinese Sensible Code .................................................................................. 175
Set Length Range for Chinese Sensible Code......................................................................... 176
Chapter 4 Prefix & Suffix .......................................................................................................................... 177
1D Scanner ........................................................................................................................................... 177
Prefix Sequence .............................................................................................................................. 177
Custom Prefix.................................................................................................................................. 178
Enable/Disable Custom Prefix ................................................................................................. 178
Set Custom Prefix .................................................................................................................... 178
AIM ID Prefix ................................................................................................................................... 179
Code ID Prefix ................................................................................................................................. 180
Restore All Default Code IDs ................................................................................................... 180
Modify Code ID ........................................................................................................................ 180
Custom Suffix .................................................................................................................................. 184
Enable/Disable Custom Suffix.................................................................................................. 184
Set Custom Suffix .................................................................................................................... 184
Terminating Character Suffix ........................................................................................................... 185
Enable/Disable Terminating Character Suffix ........................................................................... 185
Set Terminating Character Suffix.............................................................................................. 185
2D Scanner ........................................................................................................................................... 186
Prefix Sequences ............................................................................................................................ 186
Custom Prefix.................................................................................................................................. 187
Enable/Disable Custom Prefix ................................................................................................. 187
Set Custom Prefix .................................................................................................................... 187
AIM ID Prefix ................................................................................................................................... 188
Code ID Prefix ................................................................................................................................. 189
Restore All Default Code IDs ................................................................................................... 189
Modify Code ID ........................................................................................................................ 189
Custom Suffix .................................................................................................................................. 193
Enable/Disable Custom Suffix.................................................................................................. 193
Set Custom Suffix .................................................................................................................... 193
Terminating Character Suffix ........................................................................................................... 194
Enable/Disable Terminating Character Suffix ........................................................................... 194
Set Terminating Character Suffix.............................................................................................. 195
Chapter 5 Scanning Preferences (For 2D Scanner Only)....................................................................... 196
Introduction ........................................................................................................................................... 196
Decode Area ......................................................................................................................................... 196
Whole Area Decoding ..................................................................................................................... 196
Specific Area Decoding ................................................................................................................... 196
Specify Decoding Area ............................................................................................................. 197
Chapter 6 Data Formatter ......................................................................................................................... 199
Introduction ........................................................................................................................................... 199
Add a Data Format ................................................................................................................................ 199
Programming with Barcodes ........................................................................................................... 200
Programming with Serial Commands .............................................................................................. 202
Enable/Disable Data Formatter ............................................................................................................. 203
Non-Match Error Beep .......................................................................................................................... 204
Enable Data Format .............................................................................................................................. 204
Change Data Format for a Single Scan................................................................................................. 205
Clear Data Format ................................................................................................................................. 205
Query Data Formats .............................................................................................................................. 206
Formatter Command Type 6 ................................................................................................................. 207
Send Commands ............................................................................................................................ 207
Move Commands ............................................................................................................................ 210
Search Commands ......................................................................................................................... 212
Miscellaneous Commands .............................................................................................................. 215
Appendix .................................................................................................................................................... 219
Factory Defaults Table........................................................................................................................... 219
Digit Barcodes (1D Scanner) ................................................................................................................. 231
Digit Barcodes (2D Scanner) ................................................................................................................. 233
Digit Barcodes ....................................................................................................................................... 235
Save/Cancel Barcodes (1D Scanner).................................................................................................... 237
Save/Cancel Barcodes (2D Scanner).................................................................................................... 238
Save/Cancel Barcodes .......................................................................................................................... 239
AIM ID Table (1D Scanner) ................................................................................................................... 240
AIM ID Table (2D Scanner) ................................................................................................................... 241
Code ID Table (1D Scanner) ................................................................................................................. 243
Code ID Table (2D Scanner) ................................................................................................................. 244
ASCII Table ........................................................................................................................................... 245
ASCII Function Key Mapping Table ....................................................................................................... 249
Symbology ID Number .......................................................................................................................... 251
Preface
Introduction
This manual provides detailed instructions for setting up and using the NLS-BS80 barcode scanner
(hereinafter referred to as “the BS80” or “the scanner”).
Chapter Descriptions
1

Chapter 1, Getting Started
: This chapter provides information on getting the scanner up
and running for the first time.

Chapter 2, System Settings
: This chapter describes the barcode programming procedure
and shows you how to configure system parameters.

Chapter 3, Symbologies
: This chapter lists all compatible symbologies and describes
how to configure the relevant parameters.

Chapter 4, Prefix & Suffix
: This chapter describes how to use prefix and suffix to
customize scanned data.

Chapter 5, Scanning Preferences : This chapter describes how to adapt your scanner to various
applications with preference setting.

Chapter 6, Data Formatter
: This chapter explains how to customize scanned data with the
data formatter.

Appendix
: This chapter offers factory defaults table and a bunch of
frequently used programming barcodes.
Safety Instructions
Read the operating instructions carefully and especially observe the safety information. If you do
not follow the safety instructions on proper handling in this manual, we assume no liability for
any resulting personal injury or damage to property.

Don’t put the scanner in places with excessively high temperatures, such as exposure to direct
sunlight.

Don’t use the scanner in extremely humid area or drastic temperature change.

The rechargeable battery is permanently built into the scanner and cannot be replaced.

Never damage the rechargeable battery. Damaging the casing of the rechargeable battery might
cause an explosion or a fire!
Chapter 1 Getting Started
Introduction
The BS80 is a wireless pocket barcode scanner equipped with 1D or 2D scan engine to meet different
needs. It is a great space-saver for busy or limited workspaces. It also supports iOS, Android, and
Windows devices through Bluetooth HID or SPP or BLE communication.
An illustrated introduction to the BS80 is included in this chapter. If you have the scanner at hand, make
good use of it to develop a better understanding of this manual. This chapter is written for normal users,
maintenance staff and software developers.
Unpacking
Open the package and take out the scanner and its accessories. Check to make sure everything on the
packing list is present and intact. If any contents are damaged or missing, please keep the original
package and contact your dealer immediately for after-sales service.
3
BS80 Scanner
1
Charging/Battery LED
2
Good Read LED
3
Data LED
4
Scan/Power Button
5
Delete/Reset Button
6
Function Button/Function LED
7
Micro USB Port
8
Product Label
9
Scan Window*
*Note: Please peel off the protective film from the scan window before reading barcodes.
4
Button Functions
Scan/Power Button
*Press the button to scan barcode.
*Hold down the button for 3 seconds to power the scanner on.
Delete/Reset Button
*Press the button to remove the corresponding data from the flash memory in one of the following
conditions before scanning the barcode to be deleted: (i) Bluetooth mode enabled but no Bluetooth
connection established; (ii) Bluetooth mode & Batch Transmission enabled; (iii) USB mode enabled
but no USB cable connection made; or (iv) USB mode & Batch Transmission enabled.
*Hold down the button for 7 seconds to reset it.
Function Button
*Press the button to turn on or off the HID keyboard of the connected iOS device in the Bluetooth
mode.
*Hold down the button for 3s to start data transmission in either of the following conditions: (i)
Bluetooth mode & Batch Transmission enabled; or (ii) USB mode enabled and the scanner
connected to PC via USB cable.
Scan/Power Button + Function Button
*Hold down the two buttons at the same time for 3 seconds to toggle between the Bluetooth mode and
USB mode.
Delete/Reset Button + Function Button
*Press the two buttons at the same time to unpair the paired Bluetooth device from the scanner in
Bluetooth mode and to make the scanner discoverable by other Bluetooth device.
*Hold down the two buttons at the same time until the green Good Read LED lights up to enable the
scanner to enter the update status.
Note: If the update fails or you accidentally enter the update status, you need to hold down the Delete/Reset button for
7s to reset the scanner.
Scan/Power Button + Delete/Reset Button
*Press the two buttons at the same time to check the battery level with the Charging/Battery LED.
*Hold down the two buttons at the same time for 3s to delete all stored data in the flash memory in
either of the conditions: (i) Bluetooth mode enabled, Bluetooth connection established, and Batch
Transmission & Require Data Transmission Confirmation enabled; or (ii) USB mode enabled, the
scanner connected to PC via USB cable and Require Data Transmission Confirmation enabled.
5
Charging the Battery
Charge the scanner by connecting it to a host device with Micro USB cable, as shown below.
Note: Low battery may result in failure or misoperation of the scanner. Before your first use, charge the
battery for 3-4 hours.
6
Connecting the BS80 to Smartphone/Tablet
1. Make sure your device has HID or SPP or BLE profile.
2. If the red Function LED on the scanner is on, hold down the Scan/Power button and Function button at
the same time for 3 seconds or scan the Bluetooth Mode barcode to switch to the Bluetooth mode.
Hold down the Delete/Reset button and Function button at the same time or scan the Delete Bluetooth
Pairing barcode to remove existing pairing information from the scanner.
Bluetooth Mode
Delete Bluetooth Pairing
3. Turn off the Power-Saving mode on your smartphone/tablet.
4. Scan the appropriate barcode below to choose HID or SPP or BLE profile before connecting the
scanner to smartphone/tablet. If you don’t know what profile your device is using, please try HID profile
first, then SPP, at last BLE profile.
HID (default)
SPP
BLE
5. Complete the following connection procedure (example: pairing with iPhone).
7
(1) Click “Settings”.
(2) Click “General”.
(3) Click “Bluetooth”.
(4) Turn it on and search the
devices.
(5) Select “BS80XXXX” to
connect.
(6) The “Connected” message
means the connection is OK.
BS80XXXX
BS80XXXX
Connected
6. After the connection is completed, the blue Function LED on the scanner will illuminate.
7. Before using WordPad file or relative APP, set keyboard language of the device to US English. Then,
scan barcodes and the barcode data will show before current cursor position. If the data cannot be sent
to smartphone/tablet, please scan the Restore Factory Defaults barcode (see Chapter 2).
Note: This product complies with Bluetooth standards. The device that communicates with this product
must support the same SPP or HID or BLE. For other Bluetooth devices with other profiles, we
cannot guarantee a connection before the product has been tested.
The communication speed and range of the product may vary due to obstacles and radio wave
condition between the product and device to which it is connected. Condition on the host device
may also affect the communication speed and range of the scanner.
8
LED Notifications
Charging/Battery LED
Red LED on
Charging in progress.
Green LED on
Fully charged.
Red and green LEDs flash alternately
Battery not found.
Red LED flashes
Low battery alert.
When the scanner is on, pressing the Scan/Power button and Delete/Reset button at the
same time for 3 seconds can display the battery level with the Charging/Battery LED.
Green LED on
Battery level is high.
Red and green LEDs on
Battery level is medium.
Red LED on
Battery level is low.
When the battery voltage is too low, the scanner will beep with flashing red Charging/Battery LED. Please
charge it immediately before the scanner shuts down mandatorily. When it shuts down, please charge it
fully before turning it back on.
Good Read LED
Green LED flashes
Good read.
Data LED
Red LED flashes
There is data in flash memory.
Red LED on
Flash memory depleted.
Function LED
9
Blue LED flashes slowly with long OFF
state
Bluetooth mode enabled, but no Bluetooth
connection established and the BS80
undiscoverable.
Blue LED flashes slowly with long ON
state
Bluetooth mode enabled, but no Bluetooth
connection established and the BS80 discoverable.
Blue LED on
Bluetooth connection established.
Blue LED flashes quickly
Data transmission via Bluetooth in progress.
Red LED on
USB mode enabled.
Red LED flashes quickly
Data transmission via USB in progress.
Turning the BS80 On/Off
Turn the scanner on: Press the Scan/Power button for 3 seconds.
Turn the scanner off: By default, the scanner automatically powers off if no operation is performed on
the scanner for 30 minutes. You can adjust the auto power-off timer. You can also turn off the scanner by
scanning the Power Off barcode. For more information, see the “Automatic/Manual Power-Off” section in
Chapter 2.
10
Scanning Instructions
Scanning 1D Barcode
Adjust the scan angle (Do not read barcode at vertical degree) or the distance between barcode and the
scanner to ensure that the length of the scan line is roughly 8mm greater than that of the barcode, as
shown below.
Scanning 2D Barcode
Adjust the scan angle and the distance between barcode and the scanner to make them fall into the
following ranges:
1. Aim the scan line across the center of the barcode.
2. Optimum scan distances: 5-20cm.
11
Chapter 2 System Settings
Introduction
This chapter describes how to configure the basic system parameters on the scanner.
Restore Factory Defaults
Restore Factory Defaults
Operating Modes
The scanner provides two operating modes: Bluetooth mode and USB mode. To switch between these
two modes, press the Scan/Power and Function buttons for 3 seconds at the same time or scan the USB
Mode or Bluetooth Mode barcode.
12
Bluetooth Mode
Bluetooth Mode (default)
When the scanner is in the Bluetooth mode, you can select a desired profile by scanning the appropriate
barcode below.
HID (default)
SPP
BLE
There are three types of data transmission via Bluetooth: Synchronous transmission, Asynchronous
transmission and Batch transmission.
(1) Synchronous transmission (default): When you scan barcodes, the data will be sent to
smartphone/tablet directly. If you are out of Bluetooth service range, scanned data will be lost.
(2) Asynchronous transmission: When you are out of Bluetooth service range, scanned data will be
stored in the flash memory. Once you are back to service range, the data will be sent to
smartphone/tablet automatically. The scanner will automatically remove it from the flash memory after
smartphone/tablet receives the data.
(3) Batch transmission: Scanned data will be stored in the flash memory no matter whether you are in
Bluetooth service range or not. You may send the stored data to smartphone/tablet in one of the following
ways: (i) hold down the Function button on the scanner for 3 seconds (Note: To suspend/resume data
transmission, press the Function button briefly.); (ii) scan the Transmit Stored Data barcode; or (iii) send
the corresponding serial command to the scanner (See the “Serial Programming Commands” manual).
13
Synchronous Transmission, Bluetooth (default)
Asynchronous Transmission, Bluetooth
Batch Transmission, Bluetooth
Transmit Stored Data
The following feature is enabled automatically when the scanner is in Bluetooth Batch mode.
Verify Receipt of Data: The scanner will keep all the stored data after transmission, which offers users
the opportunity to verify if the data is properly received and to resend the data when needed. To delete all
stored data in the flash memory, hold down the Scan/Power Button and Delete/Reset Button at the same
time for 3 seconds or scan the Clear All Stored Data barcode or send the corresponding serial command
to the scanner.
14
USB Mode
USB Mode
When the scanner is in the USB mode, you can select a desired protocol by scanning the appropriate
barcode below.
USB HID-KBW (default)
USB COM Port Emulation
There are two types of data transmission via USB: Asynchronous transmission and Batch transmission.
(1) Asynchronous transmission (default): When the scanner is not connected to PC via USB cable,
scanned data will be stored in the flash memory. When the scanner is connected to PC via USB cable,
scanned data will be sent to PC directly.
(2) Batch transmission: Scanned data will be stored in the flash memory no matter whether the scanner
is connected to PC or not.
You can sync the data from the flash memory to your PC via USB by following the procedure described
below.
Step 1: Download CDC-Virtual COM Driver from Newland website at www.newlandaidc.com and Install it
on your PC.
Step 2: Connect the scanner to your PC with USB cable. The scanner beeps when the connection
between them is established.
Step 3: Open Notepad or Office Word on your PC and make sure that your cursor is always positioned in
it. Hold down the Function button on the scanner for 3 seconds or scan the Transmit Stored Data
barcode to start data transmission from the flash memory to your PC. The scanner beeps when the
transmission is completed.
15
Batch Transmission, USB
Asynchronous Transmission, USB (default)
Transmit Stored Data
The following feature is enabled automatically when the scanner is in USB Batch mode. Moreover, you
can scan the appropriate barcode below to enable or disable this feature for USB Asynchronous mode.
Verify Receipt of Data: The scanner will keep all the stored data after transmission, which offers users
the opportunity to verify if the data is properly received and to resend the data when needed. To delete all
stored data in the flash memory, hold down the Scan/Power Button and Delete/Reset Button at the same
time for 3 seconds or scan the Clear All Stored Data barcode or send the corresponding serial command
to the scanner.
Do Not Verify Receipt of Data: All the stored data will be automatically deleted after transmission.
Do Not Verify Receipt of Data (default)
Verify Receipt of Data
Notes:
1. When the scanner switches from one operating mode to the other, it beeps along with corresponding
LED notification (For more information, see the “LED Notifications” section in Chapter 1)
2. Besides the method mentioned above, you can also hold down the Scan/Power button and Function
button at the same time for 3 seconds to toggle between the Bluetooth mode and USB mode.
16
Query Product Information
Query the Firmware Version of Embedded Scan Engine
Query the Manufacture Date of Product
Query the Serial Number of Product
Query the Firmware & Hardware Versions of Product
Query/Delete Stored Data in Flash
Query the Number of Stored Barcodes
17
Clear All Stored Data
Sound Notifications
Turn sound notifications on or off by scanning the appropriate barcode below. After this feature is enabled,
the scanner beeps when one of the following events occurs:
1. The scanner is turned on.
2. The scanner resets.
3. A barcode is decoded (including good read for removing barcode data from the flash memory).
4. The scanner switched to the Bluetooth mode or USB mode.
5. Transmitting data over Bluetooth failed.
6. iOS soft keyboard is turned on or off.
7. Batch data transmission via Bluetooth or USB starts.
8. Batch data transmission via Bluetooth or USB is interrupted.
9. Batch data transmission via Bluetooth or USB is completed.
10. The paired Bluetooth device is unpaired from the scanner.
11. The scanner is turned off.
12. USB connection between the scanner and the host device established.
13. USB connection between the scanner and the host device lost.
14. Bluetooth connection between the scanner and the host device established or lost.
Sound Notifications On (default)
Sound Notifications Off
18
Vibration Notifications
Turn vibration notifications on or off by scanning the appropriate barcode below. After this feature is
enabled, the scanner vibrates when one of the following events occurs:
1. A barcode is decoded (including good read for removing barcode data from the flash memory).
2. The scanner switched to the Bluetooth mode or USB mode.
3. iOS soft keyboard is turned on or off.
4. The paired Bluetooth device is unpaired from the scanner.
5. Batch data transmission via Bluetooth or USB starts.
6. The scanner is turned off.
Vibration Notifications On
Vibration Notifications Off (default)
Delete Bluetooth Pairing
Delete Bluetooth Pairing
19
Automatic/Manual Power-Off
By default, the scanner automatically powers off if no operation is performed on the scanner for 30
minutes. This feature can help to extend battery life.
Query Auto Power-Off Timer
Set the auto power-off timer: Scan the Set Auto Power-Off Timer barcode then one of the timers listed
below.
Set Auto Power-Off Timer
5 Minutes
10 Minutes
20 Minutes
30 Minutes (default)
60 Minutes
Permanent
20
You can power off your scanner manually by scanning the barcode below.
Power Off
Note: After the Power Off barcode is scanned, the scanner emits a long beep and then turns off.
Bluetooth Device Name
The default Bluetooth device name for a BS80 scanner combines the model name “BS80+”
(user-programmable) with the last 4 characters of the MAC address of the device (for example,
BS80+E4AC). You can configure the model name with length up to 20 characters. To change the model
name, scan the Change Bluetooth Device Name barcode, the numeric barcodes that represent the
hexadecimal value of each character contained in your desired name and the Save barcode.
Change Bluetooth Device Name
Example: Change the Bluetooth device name (model name) to “NLS1” (Hex: 0x4E/0x4C/0x53/0x31)
21
1.
Scan the Change Bluetooth Device Name barcode.
2.
Scan the numeric barcodes “4”, “E”, “4”, “C”, “5”, “3”, “3” and “1” from the “Digit Barcodes” section in
Appendix.
3.
Scan the Save barcode from the Save/Cancel Barcodes” section in Appendix.
Barcode Separator
A separator with length up to 10 characters (default: none) can be inserted between barcodes. This
feature is only available when the following two conditions are met: Bluetooth or USB batch transmission
is selected and Packet mode is off. Scan the appropriate barcode below to enable or disable this feature.
When barcode separator is enabled, the preset separator will be inserted between barcodes and it will be
sent three times after batch transmission is completed.
Enable Barcode Separator
Disable Barcode Separator (default)
To set the barcode separator, scan the Set Barcode Separator barcode, the numeric barcodes that
represent the hexadecimal value of each character contained in your desired separator and the Save
barcode.
Set Barcode Separator
Query Barcode Separator
Example: Set the barcode separator to “*” (Hex: 0x2A)
1.
Scan the Set Barcode Separator barcode.
2.
Scan the numeric barcodes “2” and “A” from the “Digit Barcodes” section in Appendix.
3.
Scan the Save barcode from the Save/Cancel Barcodes” section in Appendix.
22
Packet Mode
When Packet mode is off, data is sent in raw format (unpacketed).
When Packet mode is on, data is sent with the packet format defined below to ensure integrity of data
when received by the host or the scanner. For batch transmission, the scanner sends 0x7E, 0x01, 0x30,
0x30, 0x30, 0x30, 0x00, 0x00, 0x3B, 0x03, 0x00 to notify the host of the completion of batch
transmission.
Note that this feature is only available when using Bluetooth SPP/BLE or USB COM Port Emulation.
Packet format: {Header} {LEN} {DATA} {Trailer} {Checksum}
Header: 0x7E 0x01 0x30 0x30 0x30 0x30
LEN: Length of DATA, 2 bytes
DATA: Barcode data sent by the scanner or programming command sent by the host device
Trailer: 0x3B 0x03
Checksum: Computation sequence: 0x00+DATA; computation method is XOR, byte by byte
Host Response: {Header} {Response Value} {Response Method} {Trailer}
Header: 0x02 0x01
Response Value: 0x06 (ACK) or 0x15 (NAK)
Response Method: 0x00 (No operation), or
0x01 (2 short high-frequency beeps for ACK; 1 low-frequency beep for NAK), or
0x02 (200ms-long vibration for ACK; 1s-long vibration for NAK)
Trailer: 0x3B 0x03
Scanner Response: {Header} {Response Value} {Trailer}
Header: 0x02 0x01
Response Value: 0x06 (ACK) or 0x15 (NAK)
Trailer: 0x3B 0x03
Packet Mode On
23
Packet Mode Off (default)
NAK/ACK Retry Count
This parameter specifies the number of times the scanner retries a barcode transmission when it awaits
an ACK response from the host. Note that Packet mode must be turned on for this parameter to function.
The selection range is from 1 to 8 retries. The default value is 2 (retries).
Set ACK/NAK Retry Count
Example: Set the ACK/NAK retry count to 1
1.
Scan the Set ACK/NAK Retry Count barcode.
2.
Scan the numeric barcode “1” from the “Digit Barcodes” section in Appendix.
3.
Scan the Save barcode from the Save/Cancel Barcodes” section in Appendix.
NAK/ACK Timeout
This parameter specifies the amount of time the scanner waits for an ACK response from the host
following a barcode transmission. It is programmable in 1ms increments from 0ms to 15,000ms. A
selection of 0 disables the timeout. The default timeout is 200ms. Note that Packet mode must be turned
on for this parameter to function
.
Set ACK/NAK Timeout
Example: Set the ACK/NAK timeout to 100ms
1.
Scan the Set ACK/NAK Timeout barcode.
2.
Scan the numeric barcodes “1”, “0” and “0” from the “Digit Barcodes” section in Appendix.
3.
Scan the Save barcode from the Save/Cancel Barcodes” section in Appendix.
24
Product Serial Number
You can select whether to send product serial number or not by enabling or disabling it.
Enable Product Serial Number
Disable Product Serial Number (default)
Time Stamp
You can select whether to send date & time or not by enabling or disabling time stamp.
Enable Time Stamp
Disable Time Stamp (default)
Set Date Format
25
Format 1: mm/dd/yyyy
(example: 01/23/2011)
Format 2: dd/mm/yyyy
(example: 23/01/2011)
Format 3: yyyy/mm/dd (default)
(example: 2011/01/23)
Query Current Date & Time
Set Date & Time
Step 1: Double click on BS80Setting.exe to run BS80 Date&Time Setting Tool. Then check the
“Auto-sync date and time with the host” item on it.
Step 2: After the time in the box is in sync with the system clock, click the “Generate Barcode” button.
Step 3: Scan the barcode generated to set the date and time on the scanner.
Note: You need to run this tool on the Windows XP or WIN7 operating system.
26
Parameters of USB HID-KBW/ Bluetooth HID
Keyboard Types
27
US English (default)
Belgium
Brazil
Canada
Czech
Danmark
Finland
France
Germany, Austria
Greece
Hungary
Israel
Italy
Latin America, South America
Netherland
Norway
Poland
Portugal
28
29
Romania
Russia
Slovakia
Spain
Sweden
Switzerland
Turkey_F
Turkey_Q
UK
Japan
Character Encoding
ISO-8859-1 (default)
UTF-8
Convert Case
No Case Conversion (default)
Convert All to Upper Case
Convert All to Lower Case
Invert Upper and Lower Case Characters
30
Emulate ALT+Keypad
This feature allows any ASCII character (0x00 - 0xFF) to be sent over the numeric keypad no matter
which keyboard type is selected. Since sending a character involves multiple keystroke emulations, this
method appears less efficient. This feature is not available for Android/ iOS devices.
The following options are available:


Disable: No ASCII character is sent in the ALT+Keypad way.
Mode 1: ASCII characters not supported by the selected keyboard type but falling into 0x20~0xFF
are sent in the ALT+Keypad way.


Mode 2:
Mode 3:
ASCII characters falling into 0x20~0xFF are sent in the ALT+Keypad way.
ASCII characters falling into 0x00~0xFF are sent in the ALT+Keypad way.
Note: In the event of a conflict between Function Key Mapping and Mode 3, Function Key Mapping
shall govern.
Disable (default)
Mode 1
Mode 2
Mode 3
Example: Supposing US keyboard is selected, barcode data ”AÐF” (65/208/70) is sent as below:
(1) Mode 1 is enabled:
“A” -- Keystroke “A”
“Д -- “ALT Make” + “208” + “ALT Break”
“F” -- Keystroke “F”
(2) Mode 3 is enabled:
“A” – “ALT Make” + “065” + “ALT Break”
“Д -- “ALT Make” + “208” + “ALT Break”
“F” -- “ALT Make” + “070” + “ALT Break”
31
Function Key Mapping
When Function Key Mapping is enabled, function characters (0x00 - 0x1F) are sent as ASCII sequences
over the keypad. For more information, see the “ASCII Function Key Mapping Table” in Appendix. This
feature is not available for Android/ iOS devices.
Enable Function Key Mapping
Disable Function Key Mapping (default)
Example: Barcode data 0x16
Enable Function Key Mapping
Ctrl+V
Disable Function Key Mapping
F1
Emulate Numeric Keypad
When this feature is disabled, sending barcode data is emulated as keystroke(s) on main keyboard.
To enable this feature, scan the Emulate Numeric Keypad barcode. Sending a number (0-9) is
emulated as keystroke(s) on numeric keypad, whereas sending other characters like “+”, “-”, “*” , “/” and “.”
is still emulated as keystrokes on main keyboard.
This feature is not available for Android/ iOS devices.
Emulate Numeric Keypad
Do Not Emulate Numeric Keypad (default)
32
Code Page
The Code Page programming feature is provided to support more international characters. This feature is
only effective when ASCII characters are sent in the ALT+Keypad way.
Windows 1252 (Latin I) (default)
Windows 1251 (Cyrillic)
Example 1: Set the scanner to get proper output for Russian encoded with ISO-8859-1
1. Scan the Windows 1251 (Cyrillic) barcode.
2. Scan the Mode 3 barcode from the “Emulate ALT+Keypad” section in this chapter.
3. Scan the ISO-8859-1 barcode from the “Character Encoding” section in this chapter.
Example 2: Set the scanner to get proper output for Russian encoded with UTF-8
1. Scan the Windows 1251 (Cyrillic) barcode.
2. Scan the Mode 3 barcode from the “Emulate ALT+Keypad” section in this chapter.
3. Scan the UTF-8 barcode from the “Character Encoding” section in this chapter.
33
Inter-Character Delay for Bluetooth HID
Select an appropriate inter-character delay to avoid data loss during transmission. This parameter is only
valid in the Bluetooth HID mode.
0ms
5ms
15ms (default)
25ms
35ms
45ms
Query Inter-Character Delay
34
Inter-Keystroke Delay for USB HID-KBW
To set the inter-keystroke delay, scan the Set Inter-Keystroke Delay barcode and a desired value
barcode below.
Set Inter-Keystroke Delay
35
0ms (default)
1ms
2ms
3ms
4ms
5ms
6ms
7ms
8ms
9ms
10ms
11ms
12ms
13ms
14ms
15ms
36
Upgrading BS80 Firmware
Upgrading BS80 firmware includes upgrading system firmware and scan engine firmware.
Upgrading System Firmware
Step 1: Contact the technical support to get the BS80 Firmware Upgrade Utility and the latest system
firmware.
Step 2: Download UFCOM driver from the Newland website at www.newlandaidc.com. Install it on PC by
following the on-screen instructions. (Skip this step if it is already installed on your PC.) Make sure that
the driver is properly installed. You cannot upgrade the firmware without it.
Step 3: Turn on the scanner. Hold down the Function button and the Delete/Reset button on the scanner
at the same time until the green Good Read LED lights up.
Step 4: Run the BS80Update program. Then click “Start”.
Step 5: Connect the scanner to your PC with the USB cable. Then the update begins. The red and blue
Function LEDs flash alternately during the updating process.
37
Step 6: Wait for the “Firmware upgraded!” window to pop up and click “OK” to exit the program.
38
Notes:
1. If this utility does not operate normally, check to see if the FirmwarePath in the UpdataTool.ini file is
correct (its value should be identical with the name of the .bin file). If there is a higher version of
firmware, replace the .bin file.
2. If the update fails or you accidentally enter the update status, you need to hold down the Delete/Reset
button for 7s to reset the scanner.
39
Upgrading Scan Engine Firmware
Step 1: Contact the technical support to get the MCU Kernel Update Tool (McuUpdateTool.exe) and the
latest scan engine firmware for BS80 (.pak).
Step 2: Download UFCOM driver from the Newland website at www.newlandaidc.com. Install it on PC by
following the on-screen instructions. (Skip this step if it is already installed on your PC.) Make sure that
the driver is properly installed. You cannot upgrade the firmware without it.
Step 3: Ensure that your BS80’s system firmware version is V3.00.005 or later. Scan the following
barcode. Then the red and blue Function LEDs flash alternately.
Step 4: Connect the scanner to your PC with the USB cable.
Step 5: Double-click the McuUpdateTool.exe file to run the firmware upgrade tool. Click
and
choose the firmware file (.pak). Check your device manager for the COM port connected to the scanner
and set the COM port on the tool accordingly.
Step 6: Click the Start button to start upgrading the firmware.
40
Step 7: Wait for the upgrading to complete (Warning: It is NOT allowed to turn off your device or cut
off the power when the upgrading is in progress). When the “Update Completed” message occurs,
the upgrade has been done successfully. Note that the BS80 will automatically reboot after the update.
41
Chapter 3 Symbologies
Introduction
Every symbology (barcode type) has its own unique attributes. This chapter provides programming
barcodes for configuring the scanner so that it can identify various barcode symbologies. It is
recommended to disable those that are rarely used to increase the efficiency of the scanner.
Note: Maximum barcode length supported by the scanner is 3072 bytes.
1D Scanner
Enable/Disable All Symbologies
Enable All Symbologies
Disable All Symbologies
42
Code 128
Restore Factory Defaults
Restore the Factory Defaults of Code 128
Enable/Disable Code 128
Enable Code 128 (default)
43
Disable Code 128
Set Length Range for Code 128
The scanner can be configured to only decode Code 128 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 128
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Code 128 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 128 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
44
UCC/EAN-128
Restore Factory Defaults
Restore the Factory Defaults of UCC/EAN-128
Enable/Disable UCC/EAN-128
Enable UCC/EAN-128 (default)
45
Disable UCC/EAN-128
Set Length Range for UCC/EAN-128
The scanner can be configured to only decode UCC/EAN-128 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes UCC/EAN-128
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only UCC/EAN-128 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode UCC/EAN-128 barcodes containing between 8 and 12
characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
46
AIM 128
Restore Factory Defaults
Restore the Factory Defaults of AIM 128
Enable/Disable AIM 128
Enable AIM 128
47
Disable AIM 128 (default)
Set Length Range for AIM 128
The scanner can be configured to only decode AIM128 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes AIM128 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only AIM128
barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode AIM 128 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
48
EAN-8
Restore Factory Defaults
Restore the Factory Defaults of EAN-8
Enable/Disable EAN-8
Enable EAN-8 (default)
49
Disable EAN-8
2-Digit Add-On Code
An EAN-8 barcode can be augmented with a two-digit add-on code to form a new one.

Disable 2-Digit Add-On Code: The scanner decodes EAN-8 and ignores the add-on code when
presented with an EAN-8 plus 2-digit add-on barcode. It can also decode EAN-8 barcodes without
2-digit add-on codes.

Enable 2-Digit Add-On Code: The scanner decodes a mix of EAN-8 barcodes with and without
2-digit add-on codes.

Decode EAN-8 + 2-Digit Add-On Code Only: The scanner only decodes EAN-8 barcodes that
contain 2-digit add-on codes.
Disable 2-Digit Add-On Code (default)
Enable 2-Digit Add-On Code
Decode EAN-8 + 2-Digit Add-On Code Only
50
5-Digit Add-On Code
An EAN-8 barcode can be augmented with a five-digit add-on code to form a new one.

Disable 5-Digit Add-On Code: The scanner decodes EAN-8 and ignores the add-on code when
presented with an EAN-8 plus 5-digit add-on barcode. It can also decode EAN-8 barcodes without
5-digit add-on codes.

Enable 5-Digit Add-On Code: The scanner decodes a mix of EAN-8 barcodes with and without
5-digit add-on codes.

Decode EAN-8 + 5-Digit Add-On Code Only: The scanner only decodes EAN-8 barcodes that
contain 5-digit add-on codes.
Disable 5-Digit Add-On Code (default)
Decode EAN-8 + 5-Digit Add-On Code Only
51
Enable 5-Digit Add-On Code
EAN-8 Extension

Disable EAN-8 Zero Extend: Transmit EAN-8 barcodes as is.

Enable EAN-8 Zero Extend: Add five leading zeros to decoded EAN-8 barcodes to extend to13
digits.

Convert EAN-8 to EAN-13: Add five leading zeros to decoded EAN-8 barcodes to make them
compatible in format to EAN-13 barcodes.
Disable EAN-8 Zero Extend (default)
Enable EAN-8 Zero Extend
Convert EAN-8 to EAN-13
Transmit Check Character
EAN-8 is 8 digits in length with the last one as its check character used to verify the integrity of the data.
Transmit EAN-8 Check Character (default)
Do Not Transmit EAN-8 Check Character
52
EAN-13
Restore Factory Defaults
Restore the Factory Defaults of EAN-13
Enable/Disable EAN-13
Enable EAN-13 (default)
Disable EAN-13
Transmit Check Character
EAN-13 is 13 digits in length with the last one as its check character used to verify the integrity of the
data.
Transmit EAN-13 Check Character (default)
53
Do Not Transmit EAN-13 Check Character
2-Digit Add-On Code
An EAN-13 barcode can be augmented with a two-digit add-on code to form a new one.

Disable 2-Digit Add-On Code: The scanner decodes EAN-13 and ignores the add-on code when
presented with an EAN-13 plus 2-digit add-on barcode. It can also decode EAN-13 barcodes without
2-digit add-on codes.

Enable 2-Digit Add-On Code: The scanner decodes a mix of EAN-13 barcodes with and without
2-digit add-on codes.

Decode EAN-13 + 2-Digit Add-On Code Only: The scanner only decodes EAN-13 barcodes that
contain 2-digit add-on codes.
Disable 2-Digit Add-On Code (default)
Enable 2-Digit Add-On Code
Decode EAN-13 + 2-Digit Add-On Code Only
54
5-Digit Add-On Code
An EAN-13 barcode can be augmented with a five-digit add-on code to form a new one.

Disable 5-Digit Add-On Code: The scanner decodes EAN-13 and ignores the add-on code when
presented with an EAN-13 plus 5-digit add-on barcode. It can also decode EAN-13 barcodes without
5-digit add-on codes.

Enable 5-Digit Add-On Code: The scanner decodes a mix of EAN-13 barcodes with and without
5-digit add-on codes.

Decode EAN-13 + 5-Digit Add-On Code Only: The scanner only decodes EAN-13 barcodes that
contain 5-digit add-on codes.
Disable 5-Digit Add-On Code (default)
Decode EAN-13 + 5-Digit Add-On Code Only
55
Enable 5-Digit Add-On Code
EAN-13 Beginning with 290 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “290”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “290” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
EAN-13 Beginning with 378/379 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with a “378” or “379”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “378” or “379” must have a 2-digit or
5-digit add-on code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on
code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
56
EAN-13 Beginning with 414/419 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with a “414” or “419”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “414” or “419” must have a 2-digit or
5-digit add-on code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on
code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
EAN-13 Beginning with 434/439 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with a “434” or “439”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “434” or “439” must have a 2-digit or
5-digit add-on code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on
code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
57
Require Add-On Code
EAN-13 Beginning with 977 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “977”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “977” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
EAN-13 Beginning with 978 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “978”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “978” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
58
EAN-13 Beginning with 979 Add-On Code Required
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “979”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “979” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “2 or 5-Digit Add-On Code” feature.
Do Not Require Add-On Code (default)
59
Require Add-On Code
ISSN
Restore Factory Defaults
Restore the Factory Defaults of ISSN
Enable/Disable ISSN
Enable ISSN
Disable ISSN (default)
.
60
ISBN
Restore Factory Defaults
Restore the Factory Defaults of ISBN
Enable/Disable ISBN
Enable ISBN
Disable ISBN (default)
Set ISBN Format
ISBN-13 (default)
61
ISBN-10
UPC-E
Restore Factory Defaults
Restore the Factory Defaults of UPC-E
Enable/Disable UPC-E
Enable UPC-E (default)
Disable UPC-E
Transmit Check Character
UPC-E is 8 digits in length with the last one as its check character used to verify the integrity of the data.
Transmit UPC-E Check Character (default)
Do Not Transmit UPC-E Check Character
62
2-Digit Add-On Code
A UPC-E barcode can be augmented with a two-digit add-on code to form a new one.

Disable 2-Digit Add-On Code: The scanner decodes UPC-E and ignores the add-on code when
presented with a UPC-E plus 2-digit add-on barcode. It can also decode UPC-E barcodes without
2-digit add-on codes.

Enable 2-Digit Add-On Code: The scanner decodes a mix of UPC-E barcodes with and without
2-digit add-on codes.

Decode UPC-E + 2-Digit Add-On Code Only: The scanner only decodes UPC-E barcodes that
contain 2-digit add-on codes.
Disable 2-Digit Add-On Code (default)
Decode UPC-E + 2-Digit Add-On Code Only
63
Enable 2-Digit Add-On Code
5-Digit Add-On Code
A UPC-E barcode can be augmented with a five-digit add-on code to form a new one.

Disable 5-Digit Add-On Code: The scanner decodes UPC-E and ignores the add-on code when
presented with a UPC-E plus 5-digit add-on barcode. It can also decode UPC-E barcodes without
5-digit add-on codes.

Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-E barcodes with and without
5-digit add-on codes.

Decode UPC-E + 5-Digit Add-On Code Only: The scanner only decodes UPC-E barcodes that
contain 5-digit add-on codes.
Disable 5-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Decode UPC-E + 5-Digit Add-On Code Only
64
Transmit Preamble Character
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E
barcode. Select one of the following options for transmitting UPC-E preamble to the host device: transmit
system character only, transmit system character and country code (“0” for USA), or transmit no
preamble.
No Preamble (default)
System Character
System Character & Country Code
UPC-E Extension

Disable UPC-E Extend: Transmit UPC-E barcodes as is.

Enable UPC-E Extend: Extend UPC-E barcodes to make them compatible in length to UPC-A.

Convert UPC-E to UPC-A: Extend UPC-E barcodes to make them compatible in format to UPC-A.
Disable UPC-E Extend (default)
Convert UPC-E to UPC-A
65
Enable UPC-E Extend
UPC-A
Restore Factory Defaults
Restore the Factory Defaults of UPC-A
Enable/Disable UPC-A
Enable UPC-A (default)
Disable UPC-A
Transmit Check Character
UPC-A is 13 digits in length with the last one as its check character used to verify the integrity of the data.
Transmit UPC-A Check Character (default)
Do Not Transmit UPC-A Check Character
66
Transmit Preamble Character
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A
barcode. Select one of the following options for transmitting UPC-A preamble to the host device: transmit
system character only, transmit system character and country code (“0” for USA), or transmit no
preamble.
No Preamble
System Character & Country Code
67
System Character (default)
2-Digit Add-On Code
A UPC-A barcode can be augmented with a two-digit add-on code to form a new one.

Disable 2-Digit Add-On Code: The scanner decodes UPC-A and ignores the add-on code when
presented with a UPC-A plus 2-digit add-on barcode. It can also decode UPC-A barcodes without
2-digit add-on codes.

Enable 2-Digit Add-On Code: The scanner decodes a mix of UPC-A barcodes with and without
2-digit add-on codes.

Decode UPC-A + 2-Digit Add-On Code Only: The scanner only decodes UPC-A barcodes that
contain 2-digit add-on codes.
Disable 2-Digit Add-On Code (default)
Enable 2-Digit Add-On Code
Decode UPC-A + 2-Digit Add-On Code Only
68
5-Digit Add-On Code
A UPC-A barcode can be augmented with a five-digit add-on code to form a new one.

Disable 5-Digit Add-On Code: The scanner decodes UPC-A and ignores the add-on code when
presented with a UPC-A plus 5-digit add-on barcode. It can also decode UPC-A barcodes without
5-digit add-on codes.

Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-A barcodes with and without
5-digit add-on codes.

Decode UPC-A + 5-Digit Add-On Code Only: The scanner only decodes UPC-A barcodes that
contain 5-digit add-on codes.
Disable 5-Digit Add-On Code (default)
Decode UPC-A + 5-Digit Add-On Code Only
69
Enable 5-Digit Add-On Code
Interleaved 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Enable Interleaved 2 of 5 (default)
Disable Interleaved 2 of 5
Check Character Verification
Disable
Do Not Transmit Check Character After Verification
(default)
Transmit Check Character After Verification
70
Set Length Range for Interleaved 2 of 5
The scanner can be configured to only decode Interleaved 2 of 5 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Interleaved 2 of 5
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Interleaved 2 of 5 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Interleaved 2 of 5 barcodes containing between 8 and 12
characters
71
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
ITF-6
ITF-6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the
check character.
Restore the Factory Defaults of ITF-6
Disable ITF-6 (default)
Enable ITF-6, Do Not Transmit Check Character
Enable ITF-6, Transmit Check Character
Note: It is advisable not to enable ITF-6 and Interleaved 2 of 5 at the same time.
72
ITF-14
ITF-14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and the last character as the
check character.
Restore the Factory Defaults of ITF-14
Enable ITF-14, Do Not Transmit Check Character
Disable ITF-14 (default)
Enable ITF-14, Transmit Check Character
Note: It is advisable not to enable ITF-14 and Interleaved 2 of 5 at the same time.
73
Deutsche 14
Restore Factory Defaults
Restore the Factory Defaults of Deutsche 14
Enable/Disable Deutsche 14
Enable Deutsche 14, Do Not Transmit Check Character
Disable Deutsche 14 (default)
Enable Deutsche 14, Transmit Check Character
Note: It is advised not to enable Deutsche 14 unless necessary, because Deutsche 14, ITF-14 and
Interleaved 2 of 5 use the same encoding method and enabling them at the same time can easily cause
confusion with each other when decoding.
74
Deutsche 12
Restore Factory Defaults
Restore the Factory Defaults of Deutsche 12
Enable/Disable Deutsche 12
Enable Deutsche 12, Do Not Transmit Check Character
Disable Deutsche 12 (default)
Enable Deutsche 12, Transmit Check Character
Note: It is advised not to enable Deutsche 12 unless necessary, because Deutsche 12, ITF-12 and
Interleaved 2 of 5 use the same encoding method and enabling them at the same time can easily cause
confusion with each other when decoding.
75
COOP 25 (Japanese Matrix 2 of 5)
Restore Factory Defaults
Restore the Factory Defaults of COOP 25
Enable/Disable COOP 25
Enable COOP 25
Disable COOP 25 (default)
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
76
Set Length Range for COOP 25
The scanner can be configured to only decode COOP 25 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes COOP 25
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only COOP 25 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode COOP 25 barcodes containing between 8 and 12 characters
77
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
Matrix 2 of 5 (European Matrix 2 of 5)
Restore Factory Defaults
Restore the Factory Defaults of Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Enable Matrix 2 of 5 (default)
Disable Matrix 2 of 5
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
78
Set Length Range for Matrix 2 of 5
The scanner can be configured to only decode Matrix 2 of 5 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Matrix 2 of 5
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Matrix 2 of 5 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Matrix 2 of 5 barcodes containing between 8 and 12
characters
79
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
Industrial 25
Restore Factory Defaults
Restore the Factory Defaults of Industrial 25
Enable/Disable Industrial 25
Enable Industrial 25 (default)
Disable Industrial 25
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
80
Set Length Range for Industrial 25
The scanner can be configured to only decode Industrial 25 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Industrial 25
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Industrial 25 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Industrial 25 barcodes containing between 8 and 12
characters
81
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
Standard 25
Restore Factory Defaults
Restore the Factory Defaults of Standard 25
Enable/Disable Standard 25
Enable Standard 25 (default)
Disable Standard 25
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
82
Set Length Range for Standard 25
The scanner can be configured to only decode Standard 25 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Standard 25
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Standard 25 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Standard 25 barcodes containing between 8 and 12
characters
83
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
Code 39
Restore Factory Defaults
Restore the Factory Defaults of Code 39
Enable/Disable Code 39
Enable Code 39 (default)
Disable Code 39
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
84
Transmit Start/Stop Character
Code 39 uses an asterisk (*) for both the start and the stop characters. You can choose whether or not to
transmit the start/stop characters by scanning the appropriate barcode below.
Transmit Start/Stop Character (default)
Do Not Transmit Start/Stop Character
Enable/Disable Code 39 Full ASCII
The scanner can be configured to identify all ASCII characters by scanning the appropriate barcode
below.
Disable Code 39 Full ASCII
85
Enable Code 39 Full ASCII (default)
Set Length Range for Code 39
The scanner can be configured to only decode Code 39 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 39 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
39 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 39 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
86
Enable/Disable Code 32
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar
code below to enable or disable Code 32. Code 39 must be enabled and Code 39 check character
verification must be disabled for this parameter to function.
Disable Code 32 (default)
Enable Code 32
Code 32 Prefix
Scan the appropriate bar code below to enable or disable adding the prefix character “A” to all Code 32
barcodes. Code 32 must be enabled for this parameter to function.
Disable Code 32 Prefix (default)
87
Enable Code 32 Prefix
Transmit Code 32 Check Character
Code 32 must be enabled for this parameter to function.
Do Not Transmit Code 32 Check Character (default)
Transmit Code 32 Check Character
Transmit Code 32 Start/Stop Character
Code 32 must be enabled for this parameter to function.
Do Not Transmit Code 32 Start/Stop Character (default)
Transmit Code 32 Start/Stop Character
88
Codabar
Restore Factory Defaults
Restore the Factory Defaults of Codabar
Enable/Disable Codabar
Enable Codabar (default)
Disable Codabar
Check Character Verification
Disable (default)
Do Not Transmit Check Character After Verification
89
Transmit Check Character After Verification
Transmit Start/Stop Character
Do Not Transmit Start/Stop Character
Transmit Start/Stop Character (default)
ABCD/ABCD as the Start/Stop Character (default)
ABCD/TN*E as the Start/Stop Character
abcd/abcd as the Start/Stop Character
abcd/tn*e as the Start/Stop Character
90
Set Length Range for Codabar
The scanner can be configured to only decode Codabar barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Codabar barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only
Codabar barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Codabar barcodes containing between 8 and 12 characters
91
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
Code 93
Restore Factory Defaults
Restore the Factory Defaults of Code 93
Enable/Disable Code 93
Enable Code 93 (default)
Disable Code 93
Check Character Verification
Disable
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
(default)
92
Set Length Range for Code 93
The scanner can be configured to only decode Code 93 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 93 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
93 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 93 barcodes containing between 8 and 12 characters
93
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
Code 11
Restore Factory Defaults
Restore the Factory Defaults of Code 11
Enable/Disable Code 11
Enable Code 11
Disable Code 11 (default)
94
Check Character Verification
95
Disable
One Check Character, MOD11 (default)
Two Check Characters, MOD11/MOD11
Two Check Characters, MOD11/MOD9
One Check Character, MOD11 (Len <= 10)
One Check Character, MOD11 (Len <= 10)
Two Check Characters, MOD11/MOD11 (Len > 10)
Two Check Characters, MOD11/MOD9 (Len > 10)
Do Not Transmit Check Character (default)
Transmit Check Character
Set Length Range for Code 11
The scanner can be configured to only decode Code 11 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 11 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
11 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 11 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
96
Plessey
Restore Factory Defaults
Restore the Factory Defaults of Plessey
Enable/Disable Plessey
Enable Plessey
Disable Plessey (default)
Check Character Verification
Disable
Do Not Transmit Check Character After Verification
(default)
97
Transmit Check Character After Verification
Set Length Range for Plessey
The scanner can be configured to only decode Plessey barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Plessey barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Plessey
barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Plessey barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
98
MSI-Plessey
Restore Factory Defaults
Restore the Factory Defaults of MSI-Plessey
Enable/Disable MSI-Plessey
Enable MSI-Plessey
99
Disable MSI-Plessey (default)
Check Character Verification
Disable
One Check Character, MOD10 (default)
Two Check Characters, MOD10/MOD10
Two Check Characters, MOD10/MOD11
Do Not Transmit Check Character (default)
Transmit Check Character
100
Set Length Range for MSI-Plessey
The scanner can be configured to only decode MSI-Plessey barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes MSI-Plessey
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only MSI-Plessey barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode MSI-Plessey barcodes containing between 8 and 12
characters
101
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (1D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
GS1 Databar
Restore Factory Defaults
Restore the Factory Defaults of GS1 Databar
Enable/Disable GS1 Databar
Enable GS1 Databar (default)
Disable GS1 Databar
102
2D Scanner
Global Settings
Enable/Disable All Symbologies
If the Disable All Symbologies feature is enabled, the scanner will not be able to read any
non-programming barcodes except the programming barcodes.
Enable All Symbologies
Disable All Symbologies
Enable/Disable 1D Symbologies
If the Disable 1D Symbologies feature is enabled, the scanner will not be able to read any 1D barcodes.
Enable 1D Symbologies
Disable 1D Symbologies
Enable/Disable 2D Symbologies
If the Disable 2D Symbologies feature is enabled, the scanner will not be able to read any 2D barcodes.
Enable 2D Symbologies
103
Disable 2D Symbologies
Video Reverse
The Video Reverse feature only applies to 2D barcodes.
Regular barcode: Dark image on a bright background.
Inverse barcode: Bright image on a dark background.
The examples of regular barcode and inverse barcode are shown below.
Regular Barcode
Inverse Barcode
Video Reverse allows the scanner to read barcodes that are inverted.
Video Reverse ON: Read both regular barcodes and inverse barcodes.
Video Reverse OFF: Read regular barcodes only.
The scanner shows a slight decrease in scanning speed when Video Reverse is ON.
Video Reverse ON
Video Reverse OFF (default)
104
Code 128
Restore Factory Defaults
Restore the Factory Defaults of Code 128
Enable/Disable Code 128
Enable Code 128 (default)
105
Disable Code 128
Set Length Range for Code 128
The scanner can be configured to only decode Code 128 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 128
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Code 128 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 128 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
106
GS1-128 (UCC/EAN-128)
Restore Factory Defaults
Restore the Factory Defaults of GS1-128
Enable/Disable GS1-128
Enable GS1-128 (default)
107
Disable GS1-128
Set Length Range for GS1-128
The scanner can be configured to only decode GS1-128 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes GS1-128
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only GS1-128 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode GS1-128 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
108
AIM-128
Restore Factory Defaults
Restore the Factory Defaults of AIM-128
Enable/Disable AIM-128
Enable AIM-128 (default)
109
Disable AIM-128
Set Length Range for AIM-128
The scanner can be configured to only decode AIM-128 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes AIM-128 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only
AIM-128 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode AIM-128 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
110
EAN-8
Restore Factory Defaults
Restore the Factory Defaults of EAN-8
Enable/Disable EAN-8
Enable EAN-8 (default)
Disable EAN-8
Transmit Check Character
EAN-8 is 8 digits in length with the last one as its check character used to verify the integrity of the data.
Transmit EAN-8 Check Character (default)
111
Do Not Transmit EAN-8 Check Character
Add-On Code
An EAN-8 barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the
examples below, the part surrounded by blue dotted line is an EAN-8 barcode while the part circled by red
dotted line is add-on code.
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code (default)
Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of EAN-8
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes EAN-8 and
ignores the add-on code when presented with an EAN-8 plus add-on barcode. It can also decode EAN-8
barcodes without add-on codes.
112
Add-On Code Required
When EAN-8 Add-On Code Required is selected, the scanner will only read EAN-8 barcodes that
contain add-on codes.
EAN-8 Add-On Code Required
EAN-8 Add-On Code Not Required (default)
EAN-8 Extension
Disable EAN-8 Zero Extend: Transmit EAN-8 barcodes as is.
Enable EAN-8 Zero Extend: Add five leading zeros to decoded EAN-8 barcodes to extend to13 digits.
Enable EAN-8 Zero Extend
113
Disable EAN-8 Zero Extend (default)
EAN-13
Restore Factory Defaults
Restore the Factory Defaults of EAN-13
Enable/Disable EAN-13
Enable EAN-13 (default)
Disable EAN-13
Transmit Check Character
Transmit EAN-13 Check Character (default)
Do Not Transmit EAN-13 Check Character
114
Add-On Code
An EAN-13 barcode can be augmented with a two-digit or five-digit add-on code to form a new one.
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code (default)
Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of EAN-13
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes EAN-13 and
ignores the add-on code when presented with an EAN-13 plus add-on barcode. It can also decode
EAN-13 barcodes without add-on codes.
Add-On Code Required
When EAN-13 Add-On Code Required is selected, the scanner will only read EAN-13 barcodes that
contain add-on codes.
EAN-13 Add-On Code Required
115
EAN-13 Add-On Code Not Required (default)
EAN-13 Beginning with 290 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “290”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “290” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
EAN-13 Beginning with 378/379 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with a “378” or “379”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “378” or “379” must have a 2-digit or
5-digit add-on code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on
code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
116
EAN-13 Beginning with 414/419 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with a “414” or “419”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “414” or “419” must have a 2-digit or
5-digit add-on code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on
code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
EAN-13 Beginning with 434/439 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with a “434” or “439”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with a “434” or “439” must have a 2-digit or
5-digit add-on code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on
code is not found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
117
Require Add-On Code
EAN-13 Beginning with 977 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “977”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “977” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
EAN-13 Beginning with 978 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “978”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “978” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
Require Add-On Code
118
EAN-13 Beginning with 979 Add-On Code Required (For BS8060-2T)
This setting programs the scanner to require an add-on code (2-digit or 5-digit) on EAN-13 barcodes that
begin with “979”. The following settings can be programmed:
Require Add-On Code: All EAN-13 barcodes that begin with “979” must have a 2-digit or 5-digit add-on
code. The EAN-13 barcode with the add-on code is then transmitted. If the required add-on code is not
found, the EAN-13 barcode is discarded.
Do Not Require Add-On Code: If you have selected Require Add-On Code, and you want to disable
this feature, scan Do Not Require Add-On Code. EAN-13 barcodes are handled, depending on your
selection for the “Add-On Code Required” feature.
Do Not Require Add-On Code (default)
119
Require Add-On Code
ISSN
Restore Factory Defaults
Restore the Factory Defaults of ISSN
Enable/Disable ISSN
Enable ISSN
Disable ISSN (default)
120
Add-On Code
An ISSN barcode can be augmented with a two-digit or five-digit add-on code to form a new one.
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code (default)
Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of ISSN
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes ISSN and ignores
the add-on code when presented with an ISSN plus add-on barcode. It can also decode ISSN barcodes
without add-on codes.
Add-On Code Required
When ISSN Add-On Code Required is selected, the scanner will only read ISSN barcodes that contain
add-on codes.
ISSN Add-On Code Required
121
ISSN Add-On Code Not Required (default)
ISBN
Restore Factory Default
Restore the Factory Defaults of ISBN
Enable/Disable ISBN
Enable ISBN (default)
Disable ISBN
Set ISBN Format
ISBN-13 (default)
ISBN-10
122
Add-On Code
An ISBN barcode can be augmented with a two-digit or five-digit add-on code to form a new one.
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code (default)
Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of ISBN
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes ISBN and ignores
the add-on code when presented with an ISBN plus add-on barcode. It can also decode ISBN barcodes
without add-on codes.
Add-On Code Required
When ISBN Add-On Code Required is selected, the scanner will only read ISBN barcodes that contain
add-on codes.
ISBN Add-On Code Required
123
ISBN Add-On Code Not Required (default)
UPC-E
Restore Factory Defaults
Restore the Factory Defaults of UPC-E
Enable/Disable UPC-E
Enable UPC-E (default)
Disable UPC-E
Transmit Check Character
Transmit UPC-E Check Character (default)
Do Not Transmit UPC-E Check Character
124
Add-On Code
A UPC-E barcode can be augmented with a two-digit or five-digit add-on code to form a new one.
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code (default)
Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-E
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes UPC-E and
ignores the add-on code when presented with a UPC-E plus add-on barcode. It can also decode UPC-E
barcodes without add-on codes.
Add-On Code Required
When UPC-E Add-On Code Required is selected, the scanner will only read UPC-E barcodes that
contain add-on codes.
UPC-E Add-On Code Required
125
UPC-E Add-On Code Not Required (default)
Transmit System Character “0”
The first character of UPC-E barcode is the system character “0”.
Transmit System Character “0” (default)
Do Not Transmit System Character “0”
UPC-E Extension
Disable UPC-E Extend: Transmit UPC-E barcodes as is.
Enable UPC-E Extend: Extend UPC-E barcodes to make them compatible in length to UPC-A.
Enable UPC-E Extend
Disable UPC-E Extend (default)
126
UPC-A
Restore Factory Defaults
Restore the Factory Defaults of UPC-A
Enable/Disable UPC-A
Enable UPC-A (default)
Disable UPC-A
Transmit Check Character
Transmit UPC-A Check Character (default)
127
Do Not Transmit UPC-A Check Character
Add-On Code
A UPC-A barcode can be augmented with a two-digit or five-digit add-on code to form a new one.
Enable 2-Digit Add-On Code
Disable 2-Digit Add-On Code (default)
Enable 5-Digit Add-On Code
Disable 5-Digit Add-On Code (default)
Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-A
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes UPC-A and
ignores the add-on code when presented with a UPC-A plus add-on barcode. It can also decode UPC-A
barcodes without add-on codes.
Add-On Code Required
When UPC-A Add-On Code Required is selected, the scanner will only read UPC-A barcodes that
contain add-on codes.
UPC-A Add-On Code Required
UPC-A Add-On Code Not Required (default)
128
Transmit Preamble Character
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A
barcode. Select one of the following options for transmitting UPC-A preamble to the host device: transmit
system character only or transmit system character and country code (“0” for USA).
System Character & Country Code
129
System Character (default)
Interleaved 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Enable Interleaved 2 of 5 (default)
Disable Interleaved 2 of 5
130
Set Length Range for Interleaved 2 of 5
The scanner can be configured to only decode Interleaved 2 of 5 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Interleaved 2 of 5
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Interleaved 2 of 5 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Interleaved 2 of 5 barcodes containing between 8 and 12
characters
131
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Check Character Verification
A check character is optional for Interleaved 2 of 5 and can be added as the last character. It is a
calculated value used to verify the integrity of the data.
Disable: The scanner transmits Interleaved 2 of 5 barcodes as is.
Do Not Transmit Check Character After Verification: The scanner checks the integrity of all
Interleaved 2 of 5 barcodes to verify that the data complies with the check character algorithm. Barcodes
passing the check will be transmitted except the last digit, whereas those failing it will not be transmitted.
Transmit Check Character After Verification: The scanner checks the integrity of all Interleaved 2 of 5
barcodes to verify that the data complies with the check character algorithm. Barcodes passing the
check will be transmitted, whereas those failing it will not be transmitted.
Disable (default)
Do Not Transmit Check Character After Verification
Transmit Check Character After Verification
132
ITF-14
ITF-14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and the last character as the
check character.
Restore the Factory Defaults of ITF-14
Enable ITF-14 But Do Not Transmit Check Character
(default)
Disable ITF-14
Enable ITF-14 and Transmit Check Character
Note: It is advisable not to enable ITF-14 and Interleaved 2 of 5 at the same time.
133
ITF-6
ITF-6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the
check character.
Restore the Factory Defaults of ITF-6
Disable ITF-6 (default)
Enable ITF-6 But Do Not Transmit Check Character
Enable ITF-6 and Transmit Check Character
Note: It is advisable not to enable ITF-6 and Interleaved 2 of 5 at the same time.
134
Matrix 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Enable Matrix 2 of 5
135
Disable Matrix 2 of 5 (default)
Set Length Range for Matrix 2 of 5
The scanner can be configured to only decode Matrix 2 of 5 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Matrix 2 of 5
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Matrix 2 of 5 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Matrix 2 of 5 barcodes containing between 8 and 12
characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
136
Check Character Verification
Disable
Do Not Transmit Check Character After Verification
(default)
137
Transmit Check Character After Verification
Industrial 2 of 5
Restore Factory Defaults
Restore the Factory Defaults of Industrial 2 of 5
Enable/Disable Industrial 2 of 5
Enable Industrial 2 of 5 (default)
Disable Industrial 2 of 5
138
Set Length Range for Industrial 2 of 5
The scanner can be configured to only decode Industrial 25 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Industrial 25
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Industrial 25 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Industrial 25 barcodes containing between 8 and 12
characters
139
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
140
Standard 25 (IATA 2 of 5)
Restore Factory Defaults
Restore the Factory Defaults of Standard 25
Enable/Disable Standard 25
Enable Standard 25 (default)
141
Disable Standard 25
Set Length Range for Standard 25
The scanner can be configured to only decode Standard 25 barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Standard 25
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Standard 25 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Standard 25 barcodes containing between 8 and 12
characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
142
Check Character Verification
Disable (default)
Transmit Check Character After Verification
143
Do Not Transmit Check Character After Verification
Code 39
Restore Factory Defaults
Restore the Factory Defaults of Code 39
Enable/Disable Code 39
Enable Code 39 (default)
Disable Code 39
Transmit Start/Stop Character
Transmit Start/Stop Character
Do not Transmit Start/Stop Character (default)
144
Set Length Range for Code 39
The scanner can be configured to only decode Code 39 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 39 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
39 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 39 barcodes containing between 8 and 12 characters
145
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
Enable/Disable Code 39 Full ASCII
The scanner can be configured to identify all ASCII characters by scanning the appropriate barcode
below.
Enable Code 39 Full ASCII (default)
Disable Code 39 Full ASCII
Enable/Disable Code 32 (For BS8060-2T)
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar
code below to enable or disable Code 32. Code 39 must be enabled and Code 39 check character
verification must be disabled for this parameter to function.
Disable Code 32 (default)
Enable Code 32
146
Code 32 Prefix (For BS8060-2T)
Scan the appropriate bar code below to enable or disable adding the prefix character “A” to all Code 32
barcodes. Code 32 must be enabled for this parameter to function.
Disable Code 32 Prefix (default)
Enable Code 32 Prefix
Transmit Code 32 Check Character (For BS8060-2T)
Code 32 must be enabled for this parameter to function.
Do Not Transmit Code 32 Check Character (default)
Transmit Code 32 Check Character
Transmit Code 32 Start/Stop Character (For BS8060-2T)
Code 32 must be enabled for this parameter to function.
Do Not Transmit Code 32 Start/Stop Character (default)
147
Transmit Code 32 Start/Stop Character
Codabar
Restore Factory Defaults
Restore the Factory Defaults of Codabar
Enable/Disable Codabar
Enable Codabar (default)
Disable Codabar
148
Set Length Range for Codabar
The scanner can be configured to only decode Codabar barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Codabar barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only
Codabar barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Codabar barcodes containing between 8 and 12 characters
149
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Check Character Verification
Disable (default)
Transmit Check Character After Verification
Do Not Transmit Check Character After Verification
Transmit Start/Stop Character
Transmit Start/Stop Character
Do not Transmit Start/Stop Character (default)
150
Start/Stop Character Format
You can choose your desired start/stop character format by scanning the appropriate barcode below.
151
ABCD/ABCD as the Start/Stop Character (default)
ABCD/TN*E as the Start/Stop Character
Start/Stop Character in Uppercase
Start/Stop Character in Lowercase
Code 93
Restore Factory Defaults
Restore the Factory Defaults of Code 93
Enable/Disable Code 93
Enable Code 93 (default)
Disable Code 93
152
Set Length Range for Code 93
The scanner can be configured to only decode Code 93 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 93 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
93 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 93 barcodes containing between 8 and 12 characters
153
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Check Character Verification
Disable
Do Not Transmit Check Character After Verification
(default)
Transmit Check Character After Verification
154
GS1-Databar (RSS)
Restore Factory Defaults
Restore the Factory Defaults of GS1-Databar
Enable/Disable GS1 Databar
Enable GS1-DataBar (default)
Disable GS1-DataBar
Transmit Application Identifier “01”
Transmit Application Identifier “01” (default)
155
Do Not Transmit Application Identifier “01”
Code 11
Restore Factory Defaults
Restore the Factory Defaults of Code 11
Enable/Disable Code 11
Enable Code 11 (default)
Disable Code 11
156
Set Length Range for Code 11
The scanner can be configured to only decode Code 11 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Code 11 barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Code
11 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Code 11 barcodes containing between 8 and 12 characters
157
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Transmit Check Character
Transmit Check Character
Do Not Transmit Check Character (default)
Check Character Verification
Disable
One Check Character, MOD11 (default)
Two Check Characters, MOD11/MOD11
Two Check Characters, MOD11/MOD9
One Check Character, MOD11 (Len<=10)
One Check Character, MOD11 (Len<=10)
Two Check Characters, MOD11/MOD11 (Len>10)
Two Check Characters, MOD11/MOD9 (Len>10)
158
Plessey
Restore Factory Defaults
Restore the Factory Defaults of Plessey
Enable/Disable Plessey
Enable Plessey (default)
159
Disable Plessey
Set Length Range for Plessey
The scanner can be configured to only decode Plessey barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Plessey barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only Plessey
barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Plessey barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
160
Check Character Verification
Disable
Do Not Transmit Check Character After Verification
(default)
161
Transmit Check Character After Verification
MSI-Plessey
Restore Factory Defaults
Restore the Factory Defaults of MSI-Plessey
Enable/Disable MSI-Plessey
Enable MSI-Plessey (default)
Disable MSI-Plessey
162
Set Length Range for MSI-Plessey
The scanner can be configured to only decode MSI-Plessey barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes MSI-Plessey
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only MSI-Plessey barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode MSI-Plessey barcodes containing between 8 and 12
characters
163
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Transmit Check Character
Transmit Check Character
Do Not Transmit Check Character (default)
Check Character Verification
Disable
One Check Character, MOD10 (default)
Two Check Characters, MOD10/MOD10
Two Check Characters, MOD10/MOD11
164
PDF 417
Restore Factory Defaults
Restore the Factory Defaults of PDF 417
Enable/Disable PDF 417
Enable PDF 417 (default)
165
Disable PDF 417
Set Length Range for PDF 417
The scanner can be configured to only decode PDF 417 barcodes with lengths that fall between (inclusive)
the minimum and maximum lengths. To accomplish it, you need to set the minimum and maximum
lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes PDF 417
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only PDF 417 barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode PDF 417 barcodes containing between 8 and 12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
166
PDF 417 Twin Code
PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally. They must both be either
regular or inverse barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading PDF417 twin codes:
Single PDF417 Only: Read either PDF417 code.
Twin PDF417 Only: Read both PDF417 codes.
Both Single & Twin: Read both PDF417 codes. If successful, transmit as twin PDF417 only. Otherwise,
try single PDF417 only.
Single PDF417 Only (default)
Twin PDF417 Only
167
Both Single & Twin
QR Code
Restore Factory Defaults
Restore the Factory Defaults of QR Code
Enable/Disable QR Code
Enable QR Code (default)
Disable QR Code
Enable Micro QR (default)
Disable Micro QR
Micro QR
168
Set Length Range for QR Code
The scanner can be configured to only decode QR Code barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes QR Code
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only QR Code barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode QR Code barcodes containing between 8 and 12 characters
169
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
QR Twin Code
QR twin code is 2 QR barcodes paralleled vertically or horizontally. They must both be either regular or
inverse barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading QR twin codes:
Single QR Only: Read either QR code.
Twin QR Only: Read both QR codes.
Both Single & Twin: Read both QR codes. If successful, transmit as twin QR only. Otherwise, try single
QR only.
Single QR Only (default)
Twin QR Only
Both Single & Twin
170
Data Matrix
Restore Factory Defaults
Restore the Factory Defaults of Data Matrix
Enable/Disable Data Matrix
Enable Data Matrix (default)
171
Disable Data Matrix
Set Length Range for Data Matrix
The scanner can be configured to only decode Data Matrix barcodes with lengths that fall between
(inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum and
maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Data Matrix
barcodes with either the minimum or maximum length. If minimum length is same as maximum length,
only Data Matrix barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Data Matrix barcodes containing between 8 and 12
characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
172
Rectangular Barcode
Enable Rectangular Barcode (default)
Disable Rectangular Barcode
Mirror Image
Decode Mirror Images (default)
173
Do Not Decode Mirror Images
Data Matrix Twin Code
Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally. They must both be
either regular or inverse barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading Data Matrix twin codes:
Single Data Matrix Only: Read either Data Matrix code.
Twin Data Matrix Only: Read both Data Matrix codes. Transmission order: Data Matrix code on the left
(in the upper position) followed by the one on the right (in the lower position).
Both Single & Twin: Read both Data Matrix codes. If successful, transmit as twin Data Matrix only.
Otherwise, try single Data Matrix only.
Single Data Matrix Only (default)
Twin Data Matrix Only
Both Single & Twin
174
Chinese Sensible Code
Restore Factory Defaults
Restore the Factory Defaults of Chinese Sensible Code
Enable/Disable Chinese Sensible Code
Enable Chinese Sensible Code
175
Disable Chinese Sensible Code (default)
Set Length Range for Chinese Sensible Code
The scanner can be configured to only decode Chinese Sensible Code barcodes with lengths that fall
between (inclusive) the minimum and maximum lengths. To accomplish it, you need to set the minimum
and maximum lengths.
If minimum length is set to be greater than maximum length, the scanner only decodes Chinese Sensible
Code barcodes with either the minimum or maximum length. If minimum length is same as maximum
length, only Chinese Sensible Code barcodes with that length are to be decoded.
Set the Minimum Length
Set the Maximum Length
Example: Set the scanner to decode Chinese Sensible Code barcodes containing between 8 and
12 characters
1.
Scan the Set the Minimum Length barcode.
2.
Scan the numeric barcode “8” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Set the Maximum Length barcode.
5.
Scan the numeric barcodes “1” and “2” from the “Digit Barcodes (2D Scanner)” section in Appendix.
6.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
176
Chapter 4 Prefix & Suffix
1D Scanner
After a successful barcode reading, a string containing numbers, letters or symbols will be returned.
In real applications, barcode data may be found insufficient for your needs. You may wish to include
additional information such as barcode type, data acquisition time or delimiter in data being scanned.
Adding extra information to printed barcodes does not seem like a sensible solution since that will
increase the barcode size and make them inflexible. Instead, we come up with the idea of appending
prefix and suffix to the data without making any change to barcodes. We will show you how to conduct the
configuration in the following sections.
The scanner can be configured to transmit barcode data in the following format:
[Code ID] + [Custom Prefix] + [DATA] + [Custom Suffix] + [Terminating Character]
Note: [DATA] must be transmitted while user can decide whether to transmit any of the rest parts.
Prefix Sequence
Code ID+Custom+AIM ID (default)
177
Custom+Code ID+AIM ID
Custom Prefix
Enable/Disable Custom Prefix
If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot
exceed 11 characters.
For example, if barcode data is “123” and custom prefix is “AB”, the host device will receive “AB123”.
Disable Custom Prefix (default)
Enable Custom Prefix
Set Custom Prefix
To set a custom prefix, scan the Set Custom Prefix barcode, the numeric barcodes that represent the
hexadecimal value of desired prefix(es) and the Save barcode.
Note: A custom prefix cannot exceed 11 characters.
Set Custom Prefix
Example: Set the custom prefix to “CODE” (Hex: 0x43/0x4F/0x44/0x45)
1.
Scan the Set Custom Prefix barcode.
2.
Scan the numeric barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes (1D
Scanner)” section in Appendix.
3.
Scan the Save barcode from the Save/Cancel Barcodes (1D Scanner)” section in Appendix.
178
AIM ID Prefix
AIM (Automatic Identification Manufacturers) ID defines symbology identifier (For the details, see the
“AIM ID Table (1D Scanner)” section in Appendix). If AIM ID prefix is enabled, the scanner will add the
symbology identifier before the scanned data after decoding.
Enable AIM ID Prefix
179
Disable AIM ID Prefix(default)
Code ID Prefix
Code ID can also be used to identify barcode type. Unlike AIM ID, Code ID is user programmable. Code
ID can only consist of one or two English letters.
Disable Code ID Prefix (default)
Enable Code ID Prefix
Restore All Default Code IDs
For the information of default Code IDs, see the “Code ID Table (1D Scanner)” section in Appendix.
Restore Default Code IDs
Modify Code ID
Code ID of each symbology can be programmed separately. See the following example to learn how to
program a Code ID.
Example: Set the Code ID of Code 128 to “p”
1.
Check the hex value of “p” in the ASCII Table. (“p”: 70)
2.
Scan the Modify Code 128 Code ID barcode.
3.
Scan the numeric barcodes “7” and “0” from the “Digit Barcodes (1D Scanner)” section in Appendix.
4.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
180
181
Modify Code 128 Code ID
Modify UCC/EAN 128 Code ID
Modify AIM 128 Code ID
Modify EAN-8 Code ID
Modify EAN-13 Code ID
Modify ISSN Code ID
Modify ISBN Code ID
Modify UPC-E Code ID
Modify UPC-A Code ID
Modify Interleaved 2 of 5 Code ID
Modify ITF-6 Code ID
Modify ITF-14 Code ID
Modify Deutsche 14 Code ID
Modify Deutsche 12 Code ID
Modify COOP25 Code ID
Modify Matrix 2 of 5 Code ID
Modify Industrial 25 Code ID
Modify Standard 25 Code ID
Modify Code 39 Code ID
Modify Codabar Code ID
182
Modify Code 93 Code ID
Modify Code 11 Code ID
Modify Plessey Code ID
Modify MSI-Plessey Code ID
Modify GS1 Databar Code ID
183
Custom Suffix
Enable/Disable Custom Suffix
If custom suffix is enabled, you are allowed to append to the data a user-defined suffix that cannot exceed
11 characters.
For example, if barcode data is “123” and custom suffix is “AB”, the host device will receive “123AB”.
Disable Custom Suffix (default)
Enable Custom Suffix
Set Custom Suffix
To set a custom suffix, scan the Set Custom Suffix barcode, the numeric barcodes that represent the
hexadecimal value of desired suffix(es) and the Save barcode.
Note: A custom suffix cannot exceed 11 characters.
Set Custom Suffix
Example: Set the custom suffix to “CODE” (Hex: 0x43/0x4F/0x44/0x45)
1.
Scan the Set Custom Suffix barcode.
2.
Scan the numeric barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes (1D
Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
184
Terminating Character Suffix
Enable/Disable Terminating Character Suffix
A terminating character such as carriage return (CR) or carriage return/line feed pair (CRLF) can only be
used to mark the end of data, which means nothing can be added after it. A terminating character suffix
cannot exceed 7 characters.
Disable Terminating Character Suffix (default)
Enable Terminating Character Suffix
Set Terminating Character Suffix
To set a terminating character suffix, scan the Set Terminating Character Suffix barcode, the numeric
barcodes that represent the hexadecimal value of desired terminating character(s) and the Save
barcode.
You can also quickly set the terminating character suffix to 0x0D (CR) or 0x0D,0x0A (CRLF) and enable
the transmission of it by scanning the Terminating Character 0x0D (CR) or Terminating Character
0x0D,0x0A (CRLF) barcode below.
Terminating Character 0x0D (CR)
Terminating Character 0x0D,0x0A (CRLF)
Set Terminating Character Suffix
Example: Set the terminating character to “0x0A” (LF)
185
1.
Scan the Set Terminating Character Suffix barcode.
2.
Scan the numeric barcodes “0” and “A” from the “Digit Barcodes (1D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (1D Scanner)” section in Appendix.
2D Scanner
In many applications, barcode data needs to be edited and distinguished from one another.
Usually AIM ID and Code ID can be used as identifiers, but in some special cases customized prefix and
terminating character suffix like Carriage Return or Line Feed can also be the alternatives.
Data formatting may include:



Append AIM ID/Code ID/custom prefix before the decoded data
Append custom suffix after the decoded data
Append terminating character to the end of the data
The following formats can be used when editing barcode data:


[Code ID] + [Custom Prefix] + [AIM ID] + [DATA] + [Custom Suffix] + [Terminating Character]
[Custom Prefix] + [Code ID] + [AIM ID] + [DATA] + [Custom Suffix] + [Terminating Character]
Prefix Sequences
Code ID+Custom Prefix+AIM ID
Custom Prefix+Code ID+AIM ID (default)
186
Custom Prefix
Enable/Disable Custom Prefix
If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot
exceed 11 characters.
Enable Custom Prefix
Disable Custom Prefix (default)
Set Custom Prefix
To set a custom prefix, scan the Set Custom Prefix barcode and the numeric barcodes representing the
hexadecimal values of a desired prefix and then scan the Save barcode. Refer to the “ASCII Table” in
Appendix for hexadecimal values of characters.
Note: A custom prefix cannot exceed 11 characters.
Set Custom Prefix
Example: Set the custom prefix to “CODE”
1.
Check the hex values of “CODE” in the ASCII Table. (“CODE”: 43, 4F, 44, 45)
2.
Scan the Set Custom Prefix barcode.
3.
Scan the numeric barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes (2D
Scanner)” section in Appendix.
4.
187
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
AIM ID Prefix
AIM (Automatic Identification Manufacturers) IDs and ISO/IEC 15424 standards define symbology
identifiers and data carrier identifiers. (For the details, see the “AIM ID Table (2D Scanner)” section in
Appendix. If AIM ID prefix is enabled, the scanner will add the symbology identifier before the scanned
data after decoding.
Enable AIM ID Prefix
Disable AIM ID Prefix(default)
188
Code ID Prefix
Code ID can also be used to identify barcode type. Unlike AIM ID, Code ID is user programmable. Code
ID can only consist of one or two English letters.
Enable Code ID Prefix
Disable Code ID Prefix (default)
Restore All Default Code IDs
For the information of default Code IDs, see the “Code ID Table (2D Scanner)” section in Appendix.
Restore All Default Code IDs
Modify Code ID
Code ID of each symbology can be programmed separately. See the following example to learn how to
program a Code ID.
Example: Set the Code ID of PDF417 to “p”
189
1.
Check the hex value of “p” in the ASCII Table. (“p”: 70)
2.
Scan the Modify PDF417 Code ID barcode.
3.
Scan the numeric barcodes “7” and “0” from the “Digit Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Modify PDF417 Code ID
Modify Data Matrix Code ID
Modify QR Code ID
Modify Chinese Sensible Code ID
Modify Code 128 Code ID
Modify GS1-128 Code ID
Modify AIM-128 Code ID
Modify EAN-8 Code ID
Modify EAN-13 Code ID
Modify UPC-E Code ID
190
191
Modify UPC-A Code ID
Modify ISBN Code ID
Modify ISSN Code ID
Modify Code 39 Code ID
Modify Code 93 Code ID
Modify Interleaved 2 of 5 Code ID
Modify ITF-14 Code ID
Modify ITF-6 Code ID
Modify Codabar Code ID
Modify Industrial 25 Code ID
Modify Standard 25 Code ID
Modify Matrix 25 Code ID
Modify COOP 25 Code ID
Modify Code 11 Code ID
Modify Plessey Code ID
Modify MSI/Plessey Code ID
Modify GS1 Databar Code ID
192
Custom Suffix
Enable/Disable Custom Suffix
If custom suffix is enabled, you are allowed to append to the data a user-defined suffix that cannot exceed
11 characters.
Enable Custom Suffix
Disable Custom Suffix (default)
Set Custom Suffix
To set a custom suffix, scan the Set Custom Suffix barcode and the numeric barcodes representing the
hexadecimal values of a desired suffix and then scan the Save barcode. Refer to the “ASCII Table” in
Appendix for hexadecimal values of characters.
Note: A custom suffix cannot exceed 11 characters.
Set Custom Suffix
Example: Set the custom suffix to “CODE”
1.
Check the hex values of “CODE” in the ASCII Table. (“CODE”: 43, 4F, 44, 45)
2.
Scan the Set Custom Suffix barcode.
3.
Scan the numeric barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes (2D
Scanner)” section in Appendix.
4.
193
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Terminating Character Suffix
A terminating character can be used to mark the end of data, which means nothing can be added after it.
A terminating character suffix can contain 1-7 characters.
Enable/Disable Terminating Character Suffix
To enable/disable terminating character suffix, scan the appropriate barcode below.
Enable Terminating Character Suffix (default)
Disable Terminating Character Suffix
194
Set Terminating Character Suffix
The scanner provides a shortcut for setting the terminating character suffix to CR (0x0D) or CRLF
(0x0D,0x0A) and enabling it by scanning the appropriate barcode below.
Terminating Character CR (0x0D) (default)
Terminating Character CRLF (0x0D,0x0A)
To set a terminating character suffix, scan the Set Terminating Character Suffix barcode and the
numeric barcodes representing the hexadecimal value of a desired terminating character and then scan
the Save barcode. Refer to the “ASCII Table” in Appendix for hexadecimal values of terminating
characters.
Note: A terminating character suffix cannot exceed 7 characters.
Set Terminating Character Suffix
Example: Set the terminating character suffix to 0x0A
195
1.
Scan the Set Terminating Character Suffix barcode.
2.
Scan the numeric barcodes “0” and “A” from the “Digit Barcodes (2D Scanner)” section in Appendix.
3.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
Chapter 5 Scanning Preferences (For 2D Scanner Only)
Introduction
This chapter contains information as to how to adapt your scanner to various applications with preference
setting. For instance, to narrow the field of view of the scanner to make sure it reads only those barcodes
intended by the user.
Decode Area
Whole Area Decoding
When this option is enabled, the scanner attempts to decode barcode(s) within its field of view, from the
center to the periphery, and transmits the barcode that has been first decoded.
Whole Area Decoding (default)
Specific Area Decoding
The scanner attempts to decode barcode(s) within a specified decoding area and transmits the barcode
that has been first decoded. This option allows the scanner to narrow its field of view to make sure it
reads only those barcodes intended by the user. For instance, if multiple barcodes are placed closely
together, specific area decoding in conjunction with appropriate pre-defined decoding area will insure that
only the desired barcode is read.
Specific Area Decoding
196
Specify Decoding Area
If Specific Area Decoding is enabled, the scanner only reads barcodes that intersect the predefined
decoding area.
The default decoding area is an area of 40% top, 60% bottom, 40% left and 60% right of the scanner’s
field of view, as shown in the figure below. In the following example, the white box is the decoding area.
Since Barcode 1 passes through the decoding area, it will be read. Barcode 2 does not pass through the
decoding area, so it will not be read.
You can define the decoding area using the Top of Decoding Area, Bottom of Decoding Area, Left of
Decoding Area and Right of Decoding Area barcodes as well as numeric barcode(s) that represent(s)
a desired percentage (0-100).
0%
10
20
30
Barcode 1
40
50
Barcode 2
60
70
80
90
100
0
197
10
20
30
40
50
60
70
80
90
100%
Top of Decoding Area
Bottom of Decoding Area
Left of Decoding Area
Right of Decoding Area
Example: Set the decoding area to 20% top, 80% bottom, 20% left and 80% right:
1.
Scan the Specific Area Decoding barcode.
2.
Scan the Top of Decoding Area barcode.
3.
Scan the numeric barcodes “2” and “0” from the “Digit Barcodes (2D Scanner)” section in Appendix.
4.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
5.
Scan the Bottom of Decoding Area barcode.
6.
Scan the numeric barcodes “8” and “0” from the “Digit Barcodes (2D Scanner)” section in Appendix.
7.
Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
8.
Scan the Left of Decoding Area barcode.
9.
Scan the numeric barcodes “2” and “0” from the “Digit Barcodes (2D Scanner)” section in Appendix.
10. Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
11. Scan the Right of Decoding Area barcode.
12. Scan the numeric barcodes “8” and “0” from the “Digit Barcodes (2D Scanner)” section in Appendix.
13. Scan the Save barcode from the “Save/Cancel Barcodes (2D Scanner)” section in Appendix.
198
Chapter 6 Data Formatter
Introduction
You may use the Data Formatter to modify the scanner’s output. For example, you can use the Data
Formatter to insert characters at certain points in barcode data or to suppress/ replace/ send certain
characters in barcode data as it is scanned.
Normally, when you scan a barcode, it gets outputted automatically; however, when you create a format,
you must use a “send” command (see the “Send Commands” section in this chapter) within the format
programming to output data. The maximum size of formatter commands in a data format is 128
characters. By default, the data formatter is disabled. Enable it when required. If you have changed data
format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data
Format code below.
Default Data Format
Add a Data Format
Data format is used to edit barcode data only. You can program up to four data formats, i.e. Format_0,
Format_1, Format_2 and Format_3. When you create a data format, you must specify the application
scope of your data format (such as barcode type and data length) and include formatter commands.
When scanned data does not match your data format requirements, you will hear the non-match error
beep (if the non-match error beep is ON).
There are two methods to program a data format: Programming with barcodes and programming with
serial commands.
199
Programming with Barcodes
The following explains how to program a data format by scanning the specific barcodes. Scanning any
irrelevant barcode or failing to follow the setting procedure will result in programming failure. To find the
alphanumeric barcodes needed to create a data format, see the “Digit Barcodes” section in Appendix.
Step 1: Scan the Add Data Format barcode.
Add Data Format
Step 2: Select data format.
Scan a numeric barcode 0 or 1 or 2 or 3 to set this to Format_0 or Format_1 or Format_2 or Format_3.
Step 3: Select formatter command type.
Specify what type of formatter commands will be used. Scan a numeric barcode “6” to select formatter
command type 6. (See the “Formatter Command Type 6” section in this chapter for more information)
Step 4: Set interface type
Scan 999 for any interface type.
Step 5: Set Symbology ID Number
Refer to the “Symbology ID Number” section in Appendix and find the ID number of the symbology to
which you want to apply the data format. Scan three numeric barcodes for the symbology ID number. If
you wish to create a data format for all symbologies, scan 999.
Step 6: Set barcode data length
Specify what length of data will be acceptable for this symbology. Scan the four numeric barcodes that
represent the data length. 9999 is a universal number, indicating all lengths. For example, 32 characters
should be entered as 0032.
Step 7: Enter formatter command
Refer to the “Formatter Command Type 6” section in this chapter. Scan the alphanumeric barcodes that
represent the command you need to edit data. For example, when a command is F141, you should scan
F141. A command can contain up to 112 characters.
Step 8: Scan the Save barcode from the “Save/Cancel Barcodes” section in Appendix to save your data
format.
200
Example: Program format_0 using formatter command type 6, Code 128 containing 10 characters
applicable, send all characters followed by “A”.
201
1. Scan the Add Data Format barcode
Add a data format
2. Scan the 0 barcode
Select format_0
3. Scan the 6 barcode
Select formatter command type 6
4. Scan the 9 barcode three times
All interface types applicable
5. Scan the barcodes 002
Only Code 128 applicable
6. Scan the barcodes 0010
Only a length of 10 characters applicable
7. Scan the alphanumeric barcodes F141
Send all characters followed by “A” (HEX: 41)
8. Scan the Save barcode
Save the data format
Programming with Serial Commands
A data format can also be created by serial commands sent from the host device. The maximum size of a
command string is 128 characters. The syntax consists of the following elements:
Add Data Format Command: $$%^5917 (8 characters).
Data format: 0~3 (1 character). 0, 1, 2 and 3 represent Format_0, Format_1, Format_2 and Format_3
respectively.
Formatter command type: 6 (1 character).
Interface type: 999 (3 characters).
Symbology ID Number: The ID number of the symbology to which you want to apply the data format (3
characters). 999 indicates all symbologies.
Data length: The length of data that will be acceptable for this symbologyrs (4 characters). 9999
indicates all lengths. For example, 32 characters should be entered as 0032.
Formatter commands: The command string used to edit data (max. 128 characters). For more
information, see the “Formatter Command Type 6” section.
Note: Serial command used to create a data format must conform to the syntax above. Returning
“\r\n$$%~OK\r\n\” indicates success; returning “\r\n$$%~ER\r\n” indicates failure.
Example: Program format_0 using formatter command type 6, Code 128 containing 10 characters
applicable, send all characters followed by “A”.
Serial command: $$%^5917069990020010F141
202
Enable/Disable Data Formatter
When Data Formatter is disabled, the data format you have enabled becomes invalid.
** Disable Data Formatter
You may wish to require the data to conform to a data format you have created. The following settings
can be applied to your data format:
Enable Data Formatter, Required, Keep Prefix/Suffix: Scanned data that meets your data format
requirements is modified accordingly and gets outputted along with prefixes and suffixes (if prefix and
suffix are enabled). Any data that does not match your data format requirements generates an error beep
(if Non-Match Error Beep is turned ON) and the data in that barcode is not transmitted.
Enable Data Formatter, Required, Drop Prefix/Suffix: Scanned data that meets your data format
requirements is modified accordingly and gets outputted without prefixes and suffixes (even if prefix and
suffix are enabled). Any data that does not match your data format requirements generates an error beep
(if Non-Match Error Beep is turned ON) and the data in that barcode is not transmitted.
Enable Data Formatter, Not Required, Keep Prefix/Suffix: Scanned data that meets your data format
requirements is modified accordingly and gets outputted along with prefixes and suffixes (if prefix and
suffix are enabled). Barcode data that does not match your data format requirements is transmitted as
read along with prefixes and suffixes (if prefix and suffix are enabled).
Enable Data Formatter, Not Required, Drop Prefix/Suffix: Scanned data that meets your data format
requirements is modified accordingly and gets outputted without prefixes and suffixes (even if prefix and
suffix are enabled). Barcode data that does not match your data format requirements is transmitted as
read along with prefixes and suffixes (if prefix and suffix are enabled).
Enable Data Formatter, Required, Keep Prefix/Suffix
203
Enable Data Formatter, Required, Drop Prefix/Suffix
Enable Data Formatter, Not Required, Keep Prefix/Suffix
Enable Data Formatter, Not Required, Drop Prefix/Suffix
Non-Match Error Beep
If Non-Match Error Beep is turned ON, the scanner generates an error beep when a barcode is
encountered that does not match your required data format.
** Non-Match Error Beep ON
Non-Match Error Beep OFF
Enable Data Format
After enabling the Data Formatter, you may select a data format you want to use by scanning the
appropriate barcode below.
** Format_0
Format_1
Format_2
Format_3
204
Change Data Format for a Single Scan
You can switch between data formats for a single scan. The next barcode is scanned using the data
format selected here, then reverts to the format you have selected above. For example, you may have set
your scanner to the data format you saved as Format_3. You can switch to Format_1 for a single trigger
pull by scanning the Single Scan – Format_1 barcode below. The next barcode that is scanned uses
Format_1, then reverts back to Format_3.
Note: This setting will be lost by removing power from the scanner, or turning off/ rebooting the device.
Single Scan – Format_0
Single Scan – Format_1
Single Scan – Format_2
Single Scan – Format_3
Clear Data Format
To delete all data formats, scan the barcode below.
Clear All
205
Query Data Formats
You may scan the following barcode to get the information of data format(s) you have created. For
instance, if you have added Format_0 as per the example in the “Programming with Barcodes” section in
this chapter, then the query result will be Data Format 0:069990020010F141;.
Query Data Formats
206
Formatter Command Type 6
When working with the Data Formatter, a virtual cursor is moved along your input data string. The
following commands are used to both move this cursor to different positions, and to select, replace, and
insert data into the final output. For the hex value of ASCII characters involved in the commands, refer to
the “ASCII Table” in Appendix.
Send Commands
F1 Send all characters
Syntax=F1xx (xx: The insert character’s hex value)
Include in the output message all of the characters from the input message, starting from current cursor
position, followed by an insert character.
F2 Send a number of characters
Syntax=F2nnxx (nn: The numeric value (00-99) for the number of characters; xx: The insert character’s
hex value)
Include in the output message a number of characters followed by an insert character. Start from the
current cursor position and continue for “nn” characters or through the last character in the input message,
followed by character “xx.”
F2 Example: Send a number of characters
Send the first 10 characters from the barcode above, followed by a carriage return.
Command string: F2100D
F2 is the “Send a number of characters” command
10 is the number of characters to send
0D is the hex value for a CR
The data is output as: 1234567890
<CR>
207
F3 Send all characters up to a particular character
Syntax=F3ssxx (ss: The particular character’s hex value; xx: The insert character’s hex value)
Include in the output message all characters from the input message, starting with the character at the
current cursor position and continuing to, but not including, the particular character “ss,” followed by
character “xx.” The cursor is moved forward to the “ss” character.
F3 Example: Send all characters up to a particular character
Using the barcode above, send all characters up to but not including “D,” followed by a carriage return.
Command string: F3440D
F3 is the “Send all characters up to a particular character” command
44 is the hex value for a “D”
0D is the hex value for a CR
The data is output as: 1234567890ABC
<CR>
E9 Send all but the last characters
Syntax=E9nn (nn: The numeric value (00-99) for the number of characters that will not be sent at the end
of the message)
Include in the output message all but the last “nn” characters, starting from the current cursor position.
The cursor is moved forward to one position past the last input message character included.
F4 Insert a character multiple times
Syntax=F4xxnn (xx: The insert character’s hex value; nn: The numeric value (00-99) for the number of
times it should be sent)
Send “xx” character “nn” times in the output message, leaving the cursor in the current position.
208
E9 and F4 Example: Send all but the last characters, followed by 2 tabs
Send all characters except for the last 8 from the barcode above, followed by 2 tabs.
Command string: E908F40902
E9 is the “Send all but the last characters” command
08 is the number of characters at the end to ignore
F4 is the “Insert a character multiple times” command
09 is the hex value for a horizontal tab
02 is the number of times the tab character is sent
The data is output as: 1234567890AB<tab><tab>
B3 Insert symbology name
Insert the name of the barcode’s symbology in the output message, without moving the cursor.
B4 Insert barcode length
Insert the barcode’s length in the output message, without moving the cursor. The length is expressed as
a numeric string and does not include leading zeros.
209
B3 and B4 Example: Insert the symbology name and length
Send the symbology name and length before the barcode data from the barcode above. Break up these
insertions with spaces. End with a carriage return.
Command string: B3F42001B4F42001F10D
B3 is the “Insert symbology name” command
F4 is the “Insert a character multiple times” command
20 is the hex value for a space
01 is the number of time the space character is sent
B4 is the “Insert barcode length” command
F4 is the “Insert a character multiple times” command
20 is the hex value for a space
01 is the number of time the space character is sent
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: Code128 20 1234567890ABCDEFGHIJ
<CR>
Move Commands
F5 Move the cursor forward a number of characters
Syntax=F5nn (nn: The numeric value (00-99) for the number of characters the cursor should be moved
ahead)
Move the cursor ahead “nn” characters from current cursor position.
210
F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above.
End with a carriage return.
Command string: F503F10D
F5 is the “Move the cursor forward a number of characters” command
03 is the number of characters to move the cursor
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 4567890ABCDEFGHIJ
<CR>
F6 Move the cursor backward a number of characters
Syntax=F6nn (nn: The numeric value (00-99) for the number of characters the cursor should be moved
back)
Move the cursor back “nn” characters from current cursor position.
F7 Move the cursor to the beginning
Syntax=F7
Move the cursor to the first character in the input message.
EA Move the cursor to the end
Syntax=EA
Move the cursor to the last character in the input message.
211
Search Commands
F8 Search forward for a character
Syntax=F8xx (xx: The search character’s hex value)
Search the input message forward for “xx” character from the current cursor position, leaving the cursor
pointing to the “xx” character.
F8 Example: Send barcode data that starts after a particular character
Search for the letter “D” in barcodes and send all the data that follows, including the “D”. Using the
barcode above:
Command string: F844F10D
F8 is the “Search forward for a character” command
44 is the hex value for “D”
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: DEFGHIJ
<CR>
F9 Search backward for a character
Syntax=F9xx (xx: The search character’s hex value)
Search the input message backward for “xx” character from the current cursor position, leaving the cursor
pointing to the “xx” character.
212
B0 Search forward for a string
Syntax=B0nnnnS (nnnn: The string length (up to 9999); S: The ASCII hex value of each character in the
string)
Search forward for “S” string from the current cursor position, leaving cursor pointing to “S” string. For
example, B0000454657374 will search forward for the first occurrence of the 4-character string “Test.”
B0 Example: Send barcode data that starts after a string of characters
Search for the letters “FGH” in barcodes and send all the data that follows, including “FGH.” Using the
barcode above:
Command string: B00003464748F10D
B0 is the “Search forward for a string” command
0003 is the string length (3 characters)
46 is the hex value for “F”
47 is the hex value for “G”
48 is the hex value for “H”
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: FGHIJ
<CR>
B1 Search backward for a string
Syntax=B1nnnnS (nnnn: The string length (up to 9999); S: The ASCII hex value of each character in the
string)
Search backward for “S” string from the current cursor position, leaving cursor pointing to “S” string. For
example, B1000454657374 will search backward for the first occurrence of the 4-character string “Test.”
213
E6 Search forward for a non-matching character
Syntax=E6xx (xx: The search character’s hex value)
Search the input message forward for the first non-“xx” character from the current cursor position, leaving
the cursor pointing to the non-“xx” character.
E6 Example: Remove zeros at the beginning of barcode data
This example shows a barcode that has been zero filled. You may want to ignore the zeros and send all
the data that follows. E6 searches forward for the first character that is not zero, then sends all the data
after, followed by a carriage return. Using the barcode above:
Command string: E630F10D
E6 is the “Search forward for a non-matching character” command
30 is the hex value for 0
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 37692
<CR>
E7 Search backward for a non-matching character
Syntax=E7xx (xx: The search character’s hex value)
Search the input message backward for the first non-“xx” character from the current cursor position,
leaving the cursor pointing to the non-“xx” character.
214
Miscellaneous Commands
FB Suppress characters
Syntax=FBnnxxyy..zz (nn: The numeric value (00-15) for the number of suppressed characters; xxyy..zz:
The hex value of the characters to be suppressed)
Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the
cursor is advanced by other commands.
FB Example: Remove spaces in barcode data
This example shows a barcode that has spaces in the data. You may want to remove the spaces before
sending the data. Using the barcode above:
Command string: FB0120F10D
FB is the “Suppress characters” command
01 is the number of the characters to be suppressed
20 is the hex value for a space
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 34567890
<CR>
215
E4 Replace characters
Syntax=E4nnxx1xx2yy1yy2…zz1zz2 (nn: The total count of the number of characters (characters to be
replaced plus replacement characters; xx1: The characters to be replaced, xx2: The replacement
characters, continuing through zz1 and zz2)
Replace up to 15 characters in the output message, without moving the cursor.
E4 Example: Replace zeros with CRs in barcode data
If the barcode has characters that the host application does not want included, you can use the E4
command to replace those characters with something else. In this example, you will replace the zeros in
the barcode above with carriage returns.
Command string: E402300DF10D
E4 is the “Replace characters” command
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR,
so total characters=2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 1234
5678
ABC
<CR>
216
BA Replace a string with another
Syntax=BAnnNN1SS1NN2SS2
nn: The count of replacements to be made, if nn=00 or nn>=the number of occurrences of a string to be
replaced, then replace all occurrences of that string.
NN1: The length of the string to be replaced, NN1>0.
SS1: The ASCII hex value of each character in the string to be replaced.
NN2: The length of replacement string, NN2>=0. To replace string “SS1” with NUL (i.e. deIete string “SS1”),
you should set NN2 to 00 and leave out SS2.
SS2: The ASCII hex value of each character in the replacement string
From the current cursor position, search forward for the occurrence of “SS1” string (of length “NN1”) and
replace the string with “SS2” string (of length “NN2”) in the output message until every “SS1” string is
replaced or the count of replacements made reaches “nn” times, without moving the cursor.
BA Example: Replace “23”s with “ABC”s in barcode data
If the barcode has a string of characters that the host application does not want included, you can use the
BA command to replace the string with something else. In this example, you will replace the “23”s in the
barcode above with “ABC”s.
Command string: BA0002323303414243F100
BA is the “Replace a string with another” command
00 is the count of replacements to be made, 00 means to replace all occurrences of that string
02 is the length of the string to be replaced
217
32 is the hex value for 2 (character in the string to be replaced)
33 is the hex value for 3 (character in the string to be replaced)
03 is the length of the replacement string
41 is the hex value for A (character in the replacement string)
42 is the hex value for B (character in the replacement string)
43 is the hex value for C (character in the replacement string)
F1 is the “Send all characters” command
00 is the hex value for a NUL
The data is output as: cd1ABCabcABCbc12abABC2
BA Example: Remove only the first occurrence of “23”s in barcode data
If the barcode has a string of characters that the host application wants removed, you can use the BA
command to replace the string with NUL. In this example, you will remove the first occurrence of “23” in
the barcode above.
Command string: BA0102323300F100
BA is the “Replace a string with another” command
01 is the count of replacements to be made
02 is the length of the string to be replaced
32 is the hex value for 2 (character in the string to be replaced)
33 is the hex value for 3 (character in the string to be replaced)
00 is the length of the replacement string, 00 means to replace the string to be replaced with NUL
F1 is the “Send all characters” command
00 is the hex value for a NUL
The data is output as: cd1abc23bc12ab232
218
Appendix
Factory Defaults Table
Parameter
Factory Default
System Settings
Operating Mode
Bluetooth mode
Bluetooth Profile
HID
Data Transmission via Bluetooth
Synchronous transmission
USB Interface Type
USB HID-KBW
Data Transmission via USB
Asynchronous transmission
Verify Receipt of Data
Disabled
Sound Notifications
Enabled
Vibration Notifications
Disabled
Bluetooth Device Name
Remark
“BS80+” with the last 4 characters of
MAC address
Barcode Separator
Disabled, None
Packet Mode
Disabled
ACK/NAK Retry Count
2
ACK/NAK Timeout
200ms
Auto Power-Off Timer
30 minutes
Product Serial Number
Disabled
Time Stamp
Date Format
Disabled
Keyboard Types
US English
USB HID-KBW/ BT HID
Character Encoding
ISO-8859-1
USB HID-KBW/ BT HID
Convert Case
No case conversion
USB HID-KBW/ BT HID
Emulate ALT + Keypad
Disabled
USB HID-KBW/ BT HID
Function Key Mapping
Disabled
USB HID-KBW/ BT HID
Emulate Numeric Keypad
Disabled
USB HID-KBW/ BT HID
Code Page
USB HID-KBW/ BT HID
Inter-Character Delay for Bluetooth HID
Windows 1252 (Latin I)
15ms
Inter-Keystroke Delay for USB HID-KBW
0ms
USB HID-KBW
219
Format 3: yyyy/mm/dd
BT HID
Parameter
Factory Default
Remark
Prefix & Suffix
1D Scanner
Prefix Sequence
Code ID+Custom Prefix+AIM ID
AIM ID Prefix
Disabled
Code ID Prefix
Disabled
Custom Prefix
Custom Suffix
Terminating Character Suffix
Disabled
None
Disabled
None
Disabled
None
1 or 2 English letters
Max: 11 characters
Max: 11 characters
Max: 7 characters
2D Scanner
Prefix Sequence
Custom Prefix
Custom Prefix+Code ID+AIM ID
Disabled
None
AIM ID Prefix
Disabled
Code ID Prefix
Disabled
Custom Suffix
Terminating Character Suffix
Disabled
None
Enabled
0x0D (CR)
Max: 11 characters
1 or 2 English letters
Max: 11 characters
Max: 7 characters
Scanning Preferences (For 2D scanner only)
Decode Area
Specify Decoding Area
Whole Area Decoding
40% top, 60% bottom, 40% left, 60%
right
Data Formatter
Data Formatter
Disabled
Data Format
Format_0
Non-Match Error Beep
On
220
Parameter
Factory Default
Symbologies
1D Scanner
Code 128
Code 128
Enabled
Maximum Length
255
Minimum Length
1
UCC/EAN-128
UCC/EAN-128
Enabled
Maximum Length
255
Minimum Length
1
AIM 128
AIM 128
Disabled
Maximum Length
255
Minimum Length
1
EAN-8
EAN-8
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Decode EAN-8 + 2-digit Add-On Code Only
Disabled
Decode EAN-8 + 5-digit Add-On Code Only
Disabled
Extend to EAN-13
Disabled
Convert to EAN-13
Disabled
EAN-13
EAN-13
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Decode EAN-13 + 2-digit Add-On Code Only
Disabled
Decode EAN-13 + 5-digit Add-On Code Only
Disabled
EAN-13 Beginning with 290 Add-On Code
Required
221
Do Not Require Add-On Code
Remark
EAN-13 Beginning with 378/379 Add-On Code
Required
EAN-13 Beginning with 414/419 Add-On Code
Required
EAN-13 Beginning with 434/439 Add-On Code
Required
EAN-13 Beginning with 977 Add-On Code
Required
EAN-13 Beginning with 978 Add-On Code
Required
EAN-13 Beginning with 979 Add-On Code
Required
Do Not Require Add-On Code
Do Not Require Add-On Code
Do Not Require Add-On Code
Do Not Require Add-On Code
Do Not Require Add-On Code
Do Not Require Add-On Code
ISSN
ISSN
Disabled
ISBN
ISBN
Disabled
ISBN Format
ISBN-13
UPC-E
UPC-E
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Decode UPC-A + 2-digit Add-On Code Only
Disabled
Decode UPC-A + 5-digit Add-On Code Only
Disabled
Extend to UPC-A
Disabled
Convert to UPC-A
Disabled
System Character
Do not transmit
Country Code
Do not transmit
UPC-A
UPC-A
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Decode UPC-A + 2-digit Add-On Code Only
Disabled
Decode UPC-A + 5-digit Add-On Code Only
Disabled
222
System Character
Transmit
Country Code
Do not transmit
Interleaved 2 of 5
Interleaved 2 of 5
Enabled
Check Character Verification
Enabled
Check Character
Do not transmit
Maximum Length
255
Minimum Length
6
No less than 2
ITF-6
ITF-6
Disabled
Check Character
Do not transmit
ITF-14
ITF-14
Disabled
Check Character
Do not transmit
Deutshe 14
Deutshe 14
Disabled
Check Character
Do not transmit
Deutshe 12
Deutshe 12
Disabled
Check Character
Do not transmit
COOP 25 (Japanese Matrix 2 of 5)
COOP 25
Disabled
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
255
Minimum Length
6
No less than 3
Matrix 25 (European Matrix 2 of 5)
Matrix 25
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
255
Minimum Length
6
Industrial 25
Industrial 25
223
Enabled
No less than 3
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
255
Minimum Length
6
No less than 4
Standard 25
Standard 25
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
255
Minimum Length
6
No less than 4
Code 39
Code 39
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Start/Stop Character
Transmit
Code 39 Full ASCII
Enabled
Code 32
Disabled
Code 32 Prefix
Disabled
Code 32 Check Character
Do not transmit
Code 32 Start/Stop Character
Do not transmit
Maximum Length
255
Minimum Length
4
No less than 1
Codabar
Codabar
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Start/Stop Character
ABCD/ABCD format
Transmit
Maximum Length
255
Minimum Length
4
No less than 2
Code 93
Code 93
Enabled
Check Character Verification
Enabled
Check Character
Do not transmit
Maximum Length
255
224
Minimum Length
2
No less than 1
Code 11
Code 11
Disabled
Check Character
Do not transmit
Check Character Verification
Enabled
1 Check Character, MOD11
Maximum Length
255
Minimum Length
4
No less than 3
Plessey
Plessey
Disabled
Check Character Verification
Enabled
Check Character
Do not transmit
Maximum Length
255
Minimum Length
4
No less than 4
MSI-Plessey
MSI-Plessey
Disabled
Check Character
Do not transmit
Check Character Verification
Enabled
1 Check Character, MOD10
Maximum Length
255
Minimum Length
4
GS1 Databar (RSS)
GS1 Databar
Enabled
Maximum Length
255
Minimum Length
1
225
No less than 4
Parameter
Factory Default
Remark
2D Scanner
Video Reverse
Disabled
Applicable to all symbologies.
Code 128
Code 128
Enabled
Maximum Length
127
Minimum Length
1
GS1-128 (UCC/EAN-128)
GS1-128
Enabled
Maximum Length
127
Minimum Length
1
AIM 128
AIM 128
Enabled
Maximum Length
127
Minimum Length
1
EAN-8
EAN-8
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Add-On Code
Not required
Extend to EAN-13
Disabled
EAN-13
EAN-13
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Add-On Code
Not required
EAN-13 Beginning with 290 Add-On Code
Required
EAN-13 Beginning with 378/379 Add-On Code
Required
EAN-13 Beginning with 414/419 Add-On Code
Required
EAN-13 Beginning with 434/439 Add-On Code
Required
Do Not Require Add-On Code For BS8060-2T
Do Not Require Add-On Code For BS8060-2T
Do Not Require Add-On Code For BS8060-2T
Do Not Require Add-On Code For BS8060-2T
226
EAN-13 Beginning with 977 Add-On Code
Required
EAN-13 Beginning with 978 Add-On Code
Required
EAN-13 Beginning with 979 Add-On Code
Required
Do Not Require Add-On Code For BS8060-2T
Do Not Require Add-On Code For BS8060-2T
Do Not Require Add-On Code For BS8060-2T
ISSN
ISSN
Disabled
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Add-On Code
Not required
ISBN
ISBN
Enabled
ISBN Format
ISBN-13
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Add-On Code
Not required
UPC-E
UPC-E
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Add-On Code
Not required
Extend to UPC-A
Disabled
System Character “0”
Transmit
UPC-A
UPC-A
Enabled
Check Character
Transmit
2-Digit Add-On Code
Disabled
5-Digit Add-On Code
Disabled
Add-On Code
Not required
System Character
Transmit
Country Code
Do not transmit
Interleaved 2 of 5
Interleaved 2 of 5
Enabled
Check Character Verification
Disabled
227
Check Character
Do not transmit
Maximum Length
100
Minimum Length
6
ITF-6
ITF-6
Disabled
Check Character
Do not transmit
ITF-14
ITF-14
Enabled
Check Character
Do not transmit
Matrix 2 of 5
Matrix 2 of 5
Disabled
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
127
Minimum Length
6
Industrial 25
Industrial 25
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
127
Minimum Length
6
Standard 25
Standard 25
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Maximum Length
127
Minimum Length
6
Code 39
Code 39
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Start/Stop Character
Do not transmit
Code 39 Full ASCII
Enabled
Code 32
Disabled
For BS8060-2T
Code 32 Prefix
Disabled
For BS8060-2T
228
Code 32 Check Character
Do not transmit
For BS8060-2T
Code 32 Start/Stop Character
Do not transmit
For BS8060-2T
Maximum Length
127
Minimum Length
2
Codabar
Codabar
Enabled
Check Character Verification
Disabled
Check Character
Do not transmit
Start/Stop Character
Do not transmit
Start/Stop Character Format
ABCD/ABCD
Maximum Length
127
Minimum Length
2
Code 93
Code 93
Enabled
Check Character Verification
Enabled
Check Character
Do not transmit
Maximum Length
127
Minimum Length
3
Code 11
Code 11
Check Character Verification
Enabled
Enabled
1 check character, MOD11
Check Character
Do not transmit
Maximum Length
127
Minimum Length
2
Plessey
Plessey
Enabled
Check Character Verification
Enabled
Check Character
Do not transmit
Maximum Length
127
Minimum Length
1
MSI-Plessey
MSI-Plessey
Check Character Verification
Check Character
229
Enabled
Enabled
1 check character, MOD10
Do not transmit
Maximum Length
127
Minimum Length
2
PDF417
PDF417
Enabled
Maximum Length
2710
Minimum Length
1
PDF 417 Twin Code
Read single PDF417 only
QR Code
QR Code
Enabled
Micro QR
Enabled
Maximum Length
7089
Minimum Length
1
QR Twin Code
Read single QR only
Data Matrix
Data Matrix
Enabled
Rectangular Barcodes
Enabled
Mirror Images
Decode
Maximum Length
3116
Minimum Length
1
DM Twin Code
Read single DM only
Chinese Sensible Code
Chinese Sensible Code
Disabled
Maximum Length
7827
Minimum Length
1
230
Digit Barcodes (1D Scanner)
0~9
231
0
1
2
3
4
5
6
7
8
9
A~F
A
B
C
D
E
F
232
Digit Barcodes (2D Scanner)
0~9
233
0
5
1
6
2
7
3
8
4
9
A~F
A
B
C
D
E
F
234
Digit Barcodes
0~9
235
0
5
1
6
2
7
3
8
4
9
A~F
A
B
C
D
E
F
236
Save/Cancel Barcodes (1D Scanner)
After reading numeric barcode(s), you need to scan the Save barcode to save the data. If you scan the
wrong digit(s), you can either scan the Cancel barcode and then start the configuration all over again, or
scan the Delete the Last Digit barcode and then the correct digit, or scan the Delete All Digits barcode
and then the digits you want.
For instance, after reading the Set the Maximum Length barcode and numeric barcodes “1”, “2” and “3”,
you scan:
237

Delete the Last Digit: The last digit “3” will be removed.

Delete All Digits: All digits “123” will be removed.

Cancel: The maximum length configuration will be canceled.
Save
Cancel
Delete the Last Digit
Delete All Digits
Save/Cancel Barcodes (2D Scanner)
After reading numeric barcode(s), you need to scan the Save barcode to save the data. If you scan the
wrong digit(s), you can either scan the Cancel barcode and then start the configuration all over again, or
scan the Delete the Last Digit barcode and then the correct digit, or scan the Delete All Digits barcode
and then the digits you want.
For instance, after reading the Maximum Length barcode and numeric barcodes “1”, “2” and “3”, you
scan:

Delete the Last Digit: The last digit “3” will be removed.

Delete All Digits: All digits “123” will be removed.

Cancel: The maximum length configuration will be cancelled. And the scanner is still in the setup
mode.
Save
Delete the Last Digit
Delete All Digits
Cancel
238
Save/Cancel Barcodes
239
Save
Cancel
Delete the Last Digit
Delete All Digits
AIM ID Table (1D Scanner)
Symbology
AIM ID
Possible AIM ID Modifiers (m)
Code 128
]C0
UCC/EAN-128
]C1
AIM 128
]C2
ISBT 128
]C4
EAN-8
]E4
EAN-13
]E0
EAN-13 with Addon
]E3
ISSN
]X0
ISBN
]X0
UPC-E
]E0
UPC-E with Addon
]E3
UPC-A
]E0
UPC-A with Addon
]E3
Interleaved 2 of 5
]Im
0,1,3
ITF-6
]Im
1,3
ITF-14
]Im
1,3
Deutsche 14
]X0
Deutsche 12
]X0
COOP 25 (Japanese Matrix 2 of 5)
]X0
Matrix 2 of 5(European Matrix 2 of 5) ]X0
Industrial 25
]S0
Standard 25
]R0
Code 39
]Am
0,1,3,4,5,7
Codabar
]Fm
0,2,4
Code 93
]G0
Code 11
]Hm
Plessey
]P0
MSI-Plessey
]Mm
GS1 Databar
]e0
PDF417
]Lm
0,1,2
MicroPDF417
]Lm
3,4,5
0,1,3
0,1
Note: “m” represents the AIM modifier character. Refer to ISO/IEC 15424:2008 Information technology – Automatic identification
and data capture techniques – Data Carrier Identifiers (including Symbology Identifiers) for AIM modifier character details.
240
AIM ID Table (2D Scanner)
Symbology
EAN-13
EAN-8
UPC-E
UPC-A
Code 128
GS1-128 (UCC/EAN-128)
AIM-128
ISBT-128
Interleaved 2 of 5
ITF-6
ITF-14
Industrial 2 of 5
Standard 2 of 5
AIM ID
]E0
]E3
]E4
]E4…]E1…
]E4…]E2…
]E0
]E3
]E0
]E3
]C0
]C1
]C2
]C4
]I0
]I1
]I3
]I1
]I3
]I1
]I3
]S0
]R0
]R8
]R9
]A0
Code 39
Codabar
Code 93
241
]A1
]A3
]A4
]A5
]A7
]F0
]F2
]F4
]G0
Remark
Standard EAN-13
EAN-13 + 2/5-Digit Add-On Code
Standard EAN-8
EAN-8 + 2-Digit Add-On Code
EAN-8 + 5-Digit Add-On Code
Standard UPC-E
UPC-E + 2/5-Digit Add-On Code
Standard UPC-A
UPC-A + 2/5-Digit Add-On Code
Standard Code 128
FNC1 is the character right after the start character
FNC1 is the 2nd character after the start character
No check character verification
Transmit check character after verification
Do not transmit check character after verification
Transmit check character
Do not transmit check character
Transmit check character
Do not transmit check character
Not specified
No check character verification
MOD10; do not transmit check character
MOD10; transmit check character
Transmit barcodes as is; Full ASCII disabled; no check character
verification
MOD43; transmit check character
MOD43; do not transmit check character
Full ASCII enabled; no check character verification
Full ASCII enabled; transmit check character
Full ASCII enabled; do not transmit check character
Standard Codabar
Transmit check character after verification
Do not transmit check character after verification
Standard Code 93
Symbology
Code 11
GS1-DataBar (RSS)
Plessey
MSI-Plessey
Matrix 2 of 5
ISBN
ISSN
PDF417
Data Matrix
AIM ID
]H0
]H1
]H3
]H9
]e0
]P0
]M0
]M1
]M7
]M8
]M9
]X0
]X1
]X2
]X3
]X4
]X5
]L0
]d0
]d1
]d2
]d3
]d4
]d5
]d6
]Q0
]Q1
]Q2
]Q3
QR Code
]Q4
]Q5
]Q6
Chinese Sensible Code
Remark
MOD11; transmit check character
MOD11/MOD11; transmit check character
Do not transmit check character after verification
No check character verification
Standard GS1-DataBar
Standard Plessey
MOD10; transmit check character
MOD10; do not transmit check character
MOD10/ MOD11; do not transmit check character
MOD10/ MOD11; transmit check character
No check character verification
Specified by the manufacturer
No check character verification
MOD10; transmit check character
MOD11; do not transmit check character
Standard ISBN
Standard ISSN
Comply with 1994 PDF417 specifications
ECC000 - ECC140
ECC200
ECC200, FNC1 is the 1st or 5th character after the start character
ECC200, FNC1 is the 2nd or 6th character after the start character
ECC200, ECI included
ECC200, FNC1 is the 1st or 5th character after the start character,ECI
included
ECC200, FNC1 is the 2nd or 6th character after the start
character,ECI included
QR1
2005 version, ECI excluded
2005 version, ECI included
QR Code 2005, ECI excluded, FNC1 is the 1st character after the
start character
QR Code 2005, ECI included, FNC1 is the 1st character after the start
character
QR Code 2005,ECI excluded,FNC1 is the 2nd character after the start
character
QR Code 2005, ECI included, FNC1 is the 2nd character after the
start character
]X0
Reference: ISO/IEC 15424:2008 Information technology – Automatic identification and data capture techniques – Data Carrier
Identifiers (including Symbology Identifiers).
242
Code ID Table (1D Scanner)
Barcode
Code ID
Code 128
j
UCC/EAN-128
u
AIM 128
f
EAN-8
g
EAN-13
d
ISSN
n
ISBN
B
UPC-E
h
UPC-A
c
Interleaved 2 of 5
e
ITF-6
r
ITF-14
q
Deutsche 14
w
Deutsche 12
l
COOP 25(Japanese Matrix 2 of 5)
o
Matrix 2 of 5(European Matrix 2 of 5)
v
Industrial 25
i
Standard 25
s
Code 39
b
Codabar
a
Code 93
y
Code 11
z
Plessey
p
MSI-Plessey
m
GS1 Databar
R
243
Code ID Table (2D Scanner)
Symbology
Code ID
Code 128
j
GS1-128(UCC/EAN-128)
j
AIM-128
f
EAN-8
d
EAN-13
d
ISSN
n
ISBN
B
UPC-E
c
UPC-A
c
Interleaved 2 of 5
e
ITF-6
e
ITF-14
e
Matrix 2 of 5
v
Industrial 2 of 5
D
Standard 2 of 5
s
Code 39
b
Codabar
a
Code 93
i
Code 11
H
Plessey
p
MSI-Plessey
m
GS1 Databar
R
PDF417
r
QR Code
Q
Data Matrix
u
Chinese Sensible Code
h
244
ASCII Table
245
Hex
Dec
Char
00
0
NUL
(Null char.)
01
1
SOH
(Start of Header)
02
2
STX
(Start of Text)
03
3
ETX
(End of Text)
04
4
EOT
(End of Transmission)
05
5
ENQ
(Enquiry)
06
6
ACK
(Acknowledgment)
07
7
BEL
(Bell)
08
8
BS
(Backspace)
09
9
HT
(Horizontal Tab)
0a
10
LF
(Line Feed)
0b
11
VT
(Vertical Tab)
0c
12
FF
(Form Feed)
0d
13
CR
(Carriage Return)
0e
14
SO
(Shift Out)
0f
15
SI
(Shift In)
10
16
DLE
(Data Link Escape)
11
17
DC1
(XON) (Device Control 1)
12
18
DC2
(Device Control 2)
13
19
DC3
(XOFF) (Device Control 3)
14
20
DC4
(Device Control 4)
15
21
NAK
(Negative Acknowledgment)
16
22
SYN
(Synchronous Idle)
17
23
ETB
(End of Trans. Block)
18
24
CAN
(Cancel)
19
25
EM
(End of Medium)
1a
26
SUB
(Substitute)
1b
27
ESC
(Escape)
1c
28
FS
(File Separator)
1d
29
GS
(Group Separator)
Hex
Dec
Char
1e
30
RS
(Request to Send)
1f
31
US
(Unit Separator)
20
32
SP
(Space)
21
33
!
(Exclamation Mark)
22
34
"
(Double Quote)
23
35
#
(Number Sign)
24
36
$
(Dollar Sign)
25
37
%
(Percent)
26
38
&
(Ampersand)
27
39
`
(Single Quote)
28
40
(
(Left/ Opening Parenthesis)
29
41
)
(Right / Closing Parenthesis)
2a
42
*
(Asterisk)
2b
43
+
(Plus)
2c
44
,
(Comma)
2d
45
-
(Minus / Dash)
2e
46
.
(Dot)
2f
47
/
(Forward Slash)
30
48
0
31
49
1
32
50
2
33
51
3
34
52
4
35
53
5
36
54
6
37
55
7
38
56
8
39
57
9
3a
58
:
(Colon)
3b
59
;
(Semi-colon)
3c
60
<
(Less Than)
3d
61
=
(Equal Sign)
246
247
Hex
Dec
Char
3e
62
>
(Greater Than)
3f
63
?
(Question Mark)
40
64
@
(AT Symbol)
41
65
A
42
66
B
43
67
C
44
68
D
45
69
E
46
70
F
47
71
G
48
72
H
49
73
I
4a
74
J
4b
75
K
4c
76
L
4d
77
M
4e
78
N
4f
79
O
50
80
P
51
81
Q
52
82
R
53
83
S
54
84
T
55
85
U
56
86
V
57
87
W
58
88
X
59
89
Y
5a
90
Z
5b
91
[
(Left / Opening Bracket)
5c
92
\
(Back Slash)
5d
93
]
(Right / Closing Bracket)
Hex
Dec
Char
5e
94
^
(Caret / Circumflex)
5f
60
95
96
_
'
(Underscore)
(Grave Accent)
61
62
97
98
a
b
63
64
99
100
c
d
65
66
101
102
e
f
67
68
103
104
g
h
69
6a
105
106
i
j
6b
6c
107
108
k
l
6d
6e
109
110
m
n
6f
70
111
112
o
p
71
72
113
114
q
r
73
74
115
116
s
t
75
76
117
118
u
v
77
78
119
120
w
x
79
7a
121
122
y
z
7b
7c
123
124
{
|
(Left/ Opening Brace)
(Vertical Bar)
7d
7e
125
126
}
~
(Right/Closing Brace)
(Tilde)
7f
127
DEL
(Delete)
248
ASCII Function Key Mapping Table
ASCII Value
(HEX)
ASCII Function
No Function Key
Mapping
Function Key Mapping
NUL
(Null char.)
00
Null
Ctrl+2
SOH
(Start of Header)
01
Keypad Enter
Ctrl+A
STX
(Start of Text)
02
Caps Lock
Ctrl+B
ETX
(End of Text)
03
Null
Ctrl+C
EOT
(End of Transmission)
04
Null
Ctrl+D
ENQ
(Enquiry)
05
Null
Ctrl+E
ACK
(Acknowledgment)
06
Null
Ctrl+F
BEL
(Bell)
07
Enter
Ctrl+G
BS
(Backspace)
08
Left Arrow
Ctrl+H
HT
(Horizontal Tab)
09
Horizontal Tab
Ctrl+I
LF
(Line Feed)
0A
Down Arrow
Ctrl+J
VT
(Vertical Tab)
0B
Vertical Tab
Ctrl+K
FF
(Form Feed)
0C
Delete
Ctrl+L
CR
(Carriage Return)
0D
Enter
Ctrl+M
SO
(Shift Out)
0E
Insert
Ctrl+N
SI
(Shift In)
0F
Esc
Ctrl+O
DLE
(Data Link Escape)
10
F11
Ctrl+P
DC1
(XON) (Device Control 1)
11
Home
Ctrl+Q
DC2
(Device Control 2)
12
Print Screen
Ctrl+R
DC3
(XOFF) (Device Control 3)
13
Backspace
Ctrl+S
DC4
(Device Control 4)
14
tab+shift
Ctrl+T
NAK
(Negative Acknowledgment)
15
F12
Ctrl+U
SYN
(Synchronous Idle)
16
F1
Ctrl+V
ETB
(End of Trans. Block)
17
F2
Ctrl+W
CAN
(Cancel)
18
F3
Ctrl+X
EM
(End of Medium)
19
F4
Ctrl+Y
SUB
(Substitute)
1A
F5
Ctrl+Z
ESC
(Escape)
1B
F6
FS
(File Separator)
1C
F7
GS
(Group Separator)
1D
F8
RS
(Request to Send)
1E
F9
US
(Unit Separator)
1F
F10
249
See the following table
ASCII Function Key Mapping Table (Continued)
The function key mappings of the last five characters in the previous table differ from one keyboard layout
to another.
Function Key Mapping
Country/
Keyboard Layout
1B
1C
1D
1E
1F
United States
Ctrl+[
Ctrl+\
Ctrl+]
Ctrl+6
Ctrl+-
Belgium
Ctrl+[
Ctrl+<
Ctrl+]
Ctrl+6
Ctrl+-
Scandinavia
Ctrl+8
Ctrl+<
Ctrl+9
Ctrl+6
Ctrl+-
France
Ctrl+^
Ctrl+8
Ctrl+$
Ctrl+6
Ctrl+=
Germany
Ctrl+Ã
Ctrl++
Ctrl+6
Ctrl+-
Italy
Ctrl+\
Ctrl++
Ctrl+6
Ctrl+-
Switzerland
Ctrl+<
Ctrl+.
Ctrl+6
Ctrl+-
United Kingdom
Ctrl+[
Ctrl+¢
Ctrl+]
Ctrl+6
Ctrl+-
Denmark
Ctrl+8
Ctrl+\
Ctrl+9
Ctrl+6
Ctrl+-
Norway
Ctrl+8
Ctrl+\
Ctrl+9
Ctrl+6
Ctrl+-
Spain
Ctrl+[
Ctrl+\
Ctrl+]
Ctrl+6
Ctrl+-
250
Symbology ID Number
Symbology
ID Number
Code 128
002
UCC/EAN-128
003
EAN-8
004
EAN-13
005
UPC-E
006
UPC-A
007
Interleaved 2 of 5, Febraban
008
ITF-14
009
ITF-6
010
Matrix 2 of 5
011
Code 39, Code 32
013
Codabar
015
Code 93
017
AIM-128
020
COOP 25
022
ISSN
023
ISBN
024
Industrial 25
025
Standard 25
026
Plessey
027
Code 11
028
MSI-Plessey
029
GS1 Databar
031
PDF417
032
QR Code
033
Data Matrix
035
Chinese Sensible Code
039
Deutsche 14
128
Deutsche 12
129
251
Newland EMEA
+31 (0) 345 87 00 33
info@newland-id.com
Newland D-A-CH
+49 (0) 6182 82916-16
info@newland-id.de
Newland UK
+44 (0) 1442 212 020
sales@newland-id.co.uk
Newland Nordic
+46 (0) 708 847 767
nordic@newland-id.com
Newland Ibérica
+34 (0) 93 303 74 66
info@newland-id.es
Newland France
+31 (0) 345 87 00 33
france@newland-id.com
Newland Middle East
+31 (0) 345 87 00 33
middleeast@newland-id.com
Newland South Africa
+27 (0) 11 553 8010
info@newland-id.co.za
Newland Italy
+39 (0) 342 056 2227
italy@newland-id.com
Newland Russia
+31 (0) 345 87 00 33
russia@newland-id.com
Newland Turkey & Iran
+90 (0) 544 538 40 49
turkey@newland-id.com
iran@newland-id.com
Download PDF
Similar pages