OWNER ’ S O PERATING M ANUAL
CL-710 / CL-710LT
Limited Warranty
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We
believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup
and care, you should enjoy many years of unparalleled video performance. Please read this consumer
protection plan carefully and retain it with your other important documents.
This is a LIMITED WARRANTY as defined by the U.S. Consumer Product Warranty and Federal Trade
Commission Improvement Act.
WHAT IS COVERED UNDER THE TERMS OF THIS WARRANTY:
SERVICE LABOR: Runco will pay for service labor by an approved Runco service center when needed
as a result of manufacturing defect for a period of two (2) years from the effective date of delivery to the
end user.
PARTS: Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in
materials or workmanship for a period of two (2) years from the effective date of delivery to the end user.
Such replacement parts are then subsequently warranted for the remaining portion (if any) of the
original warranty period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS WARRANTY:
This warranty only covers failure due to defects in materials and workmanship that occur during normal
use and does not cover normal maintenance. This warranty does not cover cabinets or any appearance
item; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or
improper installation or setup adjustments; improper maintenance, alteration, improper use of any input
signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs during
shipping or transit; or damage that is attributed to acts of God. In the case of remote control units,
damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage
under this warranty.
CAUTION: DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION
OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. IT IS
IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED RUNCO DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL ALSO
ENSURE THAT YOU ENJOY THE FINE PERFORMANCE YOUR RUNCO PRODUCT IS CAPABLE OF
PROVIDING WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL.
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the
warranty period. There are no express warranties. Runco also excludes any obligation on its part for
incidental or consequential damages related to the failure of this product to function properly. Some
states do not allow limitations on how long an implied warranty lasts, and some states do not allow the
exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user.
For your convenience, keep the original bill of sale as evidence of the purchase date.
IMPORTANT: WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how
to reach you promptly if we should discover a safety problem or product update for which you
must be notified.
TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER:
Repairs made under the terms of the Limited Warranty covering your Runco International
video product will be performed at the location of the product, during usual working hours,
providing location of product is within normal operating distance from a Runco Authorized
Service Center. If, solely in Runco’s judgement, location of product to be repaired is beyond
normal operating distance of the closest Runco Authorized Service Center, it is the owner’s
responsibility to arrange for shipment of the product for repair. These arrangements must be
made through the selling Runco dealer. If this is not possible, contact Runco directly for a
return authorization number and shipping instructions. Runco will return product transportation
prepaid in the United States, unless no product defect is discovered. In that instance, shipping
costs will be the responsibility of the owner.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco Authorized Service location, or for
additional information about this warranty, please call, write or visit our website:
CUSTOMER SERVICE DEPARTMENT
RUNCO INTERNATIONAL
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777 / Fax: (510) 324-9300
www.runco.com
Runco CL-710/ CL-710LT User’s Manual
Runco CL-710/ CL710LT Video Projector
User’s Manual
Thank you for your purchase of this quality Runco video projector! It has been designed to provide you with the quality
of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your
guide through the menus and operation.
WARNING
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated " dangerous voltage " within the product's
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this projector near water, outdoors or otherwise exposed to the elements.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the
replacement of the obsolete outlet.
9. Do not connect the RJ-11 RS-232 jack to a telephone line connection.
10. The 12V trigger only output DC 12V signal for triggering. Do not connect to any other power input or output. This
could cause damage to this unit.
11. Only use accessories specified by RUNCO International.
12. Keep the packing material in case the projector should ever need to be shipped.
13. Unplug this projector during lightning storms or when it will not be used for an extended period of time.
14. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45
minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life.
Excessive operation of lamps beyond rated life could cause them to explode in rare occasions.
15. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any
way, objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING 1
Runco CL-710/ CL-710LT User’s Manual
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Projector Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front / Upper Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear / Bottom Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connect the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjust the Lens Zoom/Focus ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjust the height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installation For CL-710 (With 1.40 - 1.60 Lens) . . . . . . . . . . . . . . . . . . 11
Throw Distance Chart For CL-710 (With 1.40 - 1.60 Lens) . . . . . . . . . 12
Installation For CL-710LT (With 1.85 - 2.40 Lens) . . . . . . . . . . . . . . . . 13
Throw Distance Chart For CL-710LT (With 1.85 - 2.40 Lens) . . . . . . 14
3.Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting Video Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Video / S-Video / Component (Interlaced Video) . . . . . . . . . . . . . . . . . . . . . . . . 15
Progressive Component (DTV Y/PB/PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
RGBHV (DTV RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting a Computer (DVI/ HDCP) . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Turning on the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Zoom/ Focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting Video Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting "ASPECT RATIO" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Direct Picture Adjust (Menu Bypass) . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Selecting Input Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PIP/ PBP function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Turning off the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Picture Quality Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warning Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Replace the Lamp (Contact your Runco Dealer) . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
RS-232 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2
WARNING
Runco CL-710/ CL-710LT User’s Manual
1. Overview
Features
■
Native 16x9 Aspect Ratio DMD
■
High Contrast and Picture Quality
12 degree mirrors with dark metal process
■
Fantastic Dynamic Performance and Rich Gray-scale
6-segment 5x color wheel with wide color space
■
TIR (Total Internal Reflection) Prism
Light engine with Cat's Eye optics for highest performance capable from an HD-2 DMD.
■
Wide Variety of Inputs
This unit can support various video formats, including Composite, S-Video, Component, DTV Y/PB/PR, DTV RGB
and Computer signals. The HDTV input (DTV Y/PB/PR and DTV RGB) is input through RGB BNC port, providing the
least amount of signal degradation caused by longer cable runs.
■
HDTV Ready
480P, 1080i and 720P (576P PAL Version) formats are all compatible with this unit (via an external DTV decoder, not
provided).
■
De-interlacing with 3:2 Pull-down
Using Runco's proprietary De-interlacing technology, this projector provides exceptional scaling and film to video
(3:2 pulldown) conversion for the most artifact-free images possible.
■
PIP/ PBP function
Picture in picture/ Picture by picture functions allow you to display two inputs on the screen at the same time.
■
Video Memory
This projector allows the user to store up to three different settings per input.
1. Overview 3
Runco CL-710/ CL-710LT User’s Manual
Projector Outlook
❚
Front / Upper Side
1. Front Lamp Cover
Remove this cover when replacing the
lamp. (See page 27.)
2. Projection Lens
3. Front IR Sensor
4. Ventilation Holes (exhaust)
6. Power LED and Lamp LED
Show the status of power and lamp.
For more details, see "Control Panel" on
page 5.
7. Top IR Sensor
8. Runco Logo (Can be turnedd off, see
"Options" on page 24.)
5. Focus Ring and Zoom Ring Access
Adjusts the focus and zoom of image.
❚
Rear / Bottom Side
1. Connector Panel
For more details, see "Connector Panel" on page 6.
2. AC Power IN Socket
3. AC Power Switch
AC main power switch
4. Ventilation Holes (intake)
5. Rear Adjusters
Adjust the height or projection angle
4
1. Overview
6. Front Adjusters
Adjust the height or projection angle
7. Ceiling Mount Holes
The connecting holes with ceiling mounting
device.
8. Ventilation Holes (exhaust)
9. Cable Access Cover
Runco CL-710/ CL-710LT User’s Manual
Controls and Functions
❚
Control Panel
1.
POWER LED
Indicate the status of the power
Orange when the AC power cord is plugged into the wall outlet (standby mode). Once in the
standby mode, you can turn on the projector by pressing the ON key on the remote control for
ONE second.
■ Green when the power is turned on (operational mode).
■ Flashing Orange for the first 45 seconds after power-up indicating that the lamp is warming up.
■ Flashing Green for 90 seconds after the projector was powered off indicating that the lamp is
cooling down.
■
2.
LAMP LED
Indicates the status of lamp
■
3.
Red when the lamp has developed a problem. Please contact your Runco Dealer for assistance.
ZOOM RING
Adjust the size of the image
■
4.
Rotate right to enlarge the image, and rotate left to make the image smaller.
FOCUS RING
Adjust the focus of the image
■
Rotate the focus ring right or left to focus the image.
1. Overview 5
Runco CL-710/ CL-710LT User’s Manual
❚
Connector Panel
1.
Video (RCA Jack)
Composite video signal input.
2.
S-Video (mini DIN 4-pin)
Y/C (S-video) signal input
3.
Component (RCA Jacks)
480i Component (Y/CB/CR) video signal input
4.
RGB/ HDTV (BNC) or Progressive Scan DVD players
DTV Y/PB/PR or DTV RGB video signal input.
5.
DVI/ HDCP
Digital/ Analog signal input.
6.
RS-232C (RJ-11 Jack)
RS-232C control signal input.
7.
12v Trigger (mini jack with the diameter of 5.5 mm outside and 2.5 mm inside)
+12V output, active when the projector is turned on.
6
1. Overview
Runco CL-710/ CL-710LT User’s Manual
❚
Remote Control
ON
Hold down this button for ONE
second to turn on the unit.
Anamorphic
For 16: 9 DVDs.
4X3
The input signal will be scaled to
fit 4: 3 display mode in the center
of screen.
LPos+, LPosLetterbox position
Letterbox
Letterbox mode. Image in letterbox format is enlarged to fit 16:9
full screen display and the upper/
lower portion are “blanked off”.
VirtualWide
4:3 image is enlarged NONlinearly in horizontal direction to
fit 16: 9 full screen display.
OFF
Press this button to turn off the
unit.
M1, M2, M3, Default
Recall video memory sequentially
(see "Selecting Video Memory" on
page 18)
Color
Adjust color intensity
Brightness
Adjust picture brightness
Contrast
Adjust picture contrast
Tint
Adjust color tones
1. Overview 7
Runco CL-710/ CL-710LT User’s Manual
Arrow (c,e,d,f)
Use to select the menu or to
make various adjustments.
Enter
Enter the setting of items in the
menu.
Picture
Access the Picture Setting menu
(see "Picture Quality
Adjustments" on page 23)
Info
Access the projector information
Exit
Exit and save the setting(s) of
items in the menu.
Menu
Turns on/off the on-screen display
menu.
Video
Composite video signal input
S-Video
S-Video signal input
PBP (Picture by Picture)
Enable the PIP function.
Comp
Component Y/CB/CR input
ACTIVE
Switch to the active window in PIP
display mode.
Comp HD
DTV Y/PB/PR signal input
PIP (Picture in Picture)
Enable the PIP function. Use
ARROW keys to adjust the
position of the PIP window (see
"PIP/ PBP function" on page 20)
PIP+
Enlarge the size of PIP window.
PIPShrink the size of PIP window.
8
1. Overview
RGB HD
DTV RGBHV signal input
DVI
Digital/ Analog signal input
Runco CL-710/ CL-710LT User’s Manual
2. Installation
Remote Control
Push forward on the tap and lift to open the cover.
Install the two AAA batteries with the correct
polarity, then close the cover.
Notes on Batteries
Make sure that the battery polarities are correct when installing the batteries.
Do not mix an old battery with a new one or different types of batteries.
■ If you will not use the remote control for a long time, remove the batteries to avoid damage from battery
leakage.
■
■
Notes on Remote Control Operation
Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver
on the projector.
■ The useable range is between 3m/ 9.8 feet (from the front of the projector) and 4m/ 13.1 feet (from the top of
the projector) within 30 degree horizontal angle and 15 degree vertical angle.
■
Projector
❚
Connect the Power Cord
Plug the supplied power cord into the AC inlet in the
rear of this unit. (AC 100V ~ 240V)
Turn on the main power switch in the rear of this unit
(next to the AC inlet). The POWER LED will light up
in orange. Press ON key on the remote control for
ONE second to turn on the unit.
2. Installation 9
Runco CL-710/ CL-710LT User’s Manual
❚
Adjust the Lens Zoom/Focus ring
Adjust the projected image size you need with the
zoom ring on the lens. To focus the image, rotate the
focus ring on the lens.
Focus
Zoom out
❚
Adjust the height
There are 4 screw adjusters on the bottom of this
unit. You can adjust the height or projection angle of
this unit by using these adjusters.
10
2. Installation
Zoom in
Runco CL-710/ CL-710LT User’s Manual
Installation For CL-710 (With 1.40 - 1.60 Lens)
Ceiling
Screen __________ (H) x __________ (W)
B) THROW DISTANCE:
CL-710 16 x 9 Screens:
Minimum: (screen width x 1.40) = __________ inches
Maximum: (screen width x 1.60) = __________ inches
C) VERTICAL OFFSET:
Screen width x 0.052 = _________ inches from the center of the lens.
Floor
2. Installation 11
Runco CL-710/ CL-710LT User’s Manual
Throw Distance Chart For CL-710 (With 1.40 - 1.60 Lens)
CL-710 @ 1280 x 720
12
Screen Height
Screen Width
Min Throw
Distance
Max Throw
Distance
Vertical Offset
Position
40.5
43
45
47
49
50
51.5
52
54
56
58
58.5
60
61
63
65
67.5
72
80
82
90
72
77
80
84
87
89
92
93
96
100
103
104
107
109
112
116
120
128
142
146
160
100.80
107.80
112.00
117.12
121.80
124.60
128.80
130.20
134.40
140.00
144.20
145.60
149.80
152.60
156.80
162.40
168.00
179.20
198.80
204.40
224.00
115.20
123.20
128.00
133.86
139.20
142.40
147.20
148.80
153.60
160.00
164.80
166.40
171.20
174.40
179.20
185.60
192.00
204.80
227.20
233.60
256.00
3.74
4.00
4.16
4.35
4.52
4.63
4.78
4.84
4.99
5.20
5.36
5.41
5.56
5.67
5.82
6.03
6.24
6.66
7.38
7.59
8.32
Screen Hight
Screen Width
Min TD
Max TD
Vertical Offset
(SWx1.40)
(SWx1.60)
Screen Width x 0.052
2. Installation
Runco CL-710/ CL-710LT User’s Manual
Installation For CL-710LT (With 1.85 - 2.40 Lens)
Ceiling
Screen __________ (H) x __________ (W)
B) THROW DISTANCE:
CL-710LT 16 x 9 Screens:
Minimum: (screen width x 1.85) = __________ inches
Maximum: (screen width x 2.40) = __________ inches
C) VERTICAL OFFSET:
Two inches offset means that the center of the projection lens is 2" above
the top of the screen (inverted ceiling) or 2" below the bottom of
the screen (upright floor mount).
Floor
2. Installation 13
Runco CL-710/ CL-710LT User’s Manual
Throw Distance Chart For CL-710LT (With 1.85 - 2.40 Lens)
CL-710LT @ 1280 x 720
Screen Height
Screen Width
Min Throw
Distance
Max Throw
Distance
Vertical Offset
Position
40.5
43
45
47
49
50
51.5
52
54
56
58
58.5
60
61
63
65
67.5
72
80
82
90
72
77
80
84
87
89
92
93
96
100
103
104
107
109
112
116
120
128
142
146
160
133.20
142.45
148.00
154.77
160.95
164.65
170.20
172.05
177.60
185.00
190.55
192.40
197.95
201.65
207.20
214.60
222.00
236.80
262.70
270.10
296.00
172.80
184.80
192.00
200.78
208.80
213.60
220.80
223.20
230.40
240.00
247.20
249.60
256.80
261.60
268.80
278.40
288.00
307.20
340.80
350.40
384.00
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
2.0"
Screen Hight
Screen Width
Min TD
Max TD
Vertical Offset
(SWx1.85)
(SWx2.40)
2.00”
Note: Two inches offset means that the center of the projection lens is 2” above the top of the screen (inverted ceiling)
or 2” below the bottom of the screen (upright floor mount).
14
2. Installation
Runco CL-710/ CL-710LT User’s Manual
3. Connecting
When connecting, make sure to:
1. Turn off all equipment before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly connected.
4. Connect all audio signals to external speakers. This projector is not equipped with speakers.
Connecting Video Inputs
❚
Video / S-Video / Component (Interlaced Video)
DVD Player
3. Connecting 15
Runco CL-710/ CL-710LT User’s Manual
❚
Progressive Component (DTV Y/PB/PR)
DTV Source
❚
RGBHV (DTV RGB)
DTV Source
The RGB BNC input supports two kinds of HDTV formats: Progressive component (DTV Y/PB/PR) and DTV RGB. The
unit will auto detect the resolution automatically.
16
3. Connecting
Runco CL-710/ CL-710LT User’s Manual
Connecting a Computer (DVI/ HDCP)
PC or Notebook
This unit is compatible with the following computer resoultions: 1280x720, 1024x768, 800x600, 640x480.
3. Connecting 17
Runco CL-710/ CL-710LT User’s Manual
4. Basic Operation
Turning on the Power
The Power LED lights orange when power is applied
and the power switch is turned on.
■ Press and hold the ON key on the remote control
for ONE second to turn on the unit. The POWER
LED will blink orange during warm up period, then
light solid green.
■ " Searching…." will be displayed on the screen before
the projector identifies the input signal. This message
will remain on the screen until a valid signal is
detected.
■ If an incompatible input signal exceeds the range of
the projector a "Not supportive timing" message will
be displayed on the screen. This message will remain
on the screen until you change the input signal.
■
Zoom/ Focusing
■
Adjust the projection image size you need with the
zoom ring on the lens. To focus the image, rotate the
focus ring on the lens.
Focus
Zoom out
Selecting Video Memory
Press M1, M2, M3 buttons to recall settings in the
memory.
■ Press Default to select the default setting.
■
18
4. Basic Operation
Zoom in
Runco CL-710/ CL-710LT User’s Manual
Selecting "ASPECT RATIO"
■
■
■
■
■
■
Select the proper aspect ratio according to the
format of signal content. There are four aspect ratios
for choice.
Anamorphic: 4:3 image is stretched horizontally to
fit the 16: 9 screen. This is for 16:9 DVDs.
4 X 3: The input signal will be scaled to fit 4 : 3
display mode in the center screen.
LPos+, LPos-: Adjust Letterbox image vertical
position.
Letterbox: Image in letterbox format is enlarged to
fit 16:9 full screen display and the upper/lower
portion are compressed.
VirtualWide: This transforms a 4x3 image to a
16x9 image.
Direct Picture Adjust (Menu Bypass)
■
Press Color to adjust color intensity.
■
Press Brightness to adjust picture brightness.
■
Press Contrast to adjust picture contrast.
■
Press Tint to adjust color tones.
Setting Menu
■
■
■
■
■
■
Press the Menu button to turn on /off the on-screen
menu.
Use the ARROW buttons (c,e,d,f) to select the
menu or to make various adjustments.
Press the Enter or f button to enter the setting of
items in the menu, or press the Exit button to leave
and save the setting of items in the menu.
For more detailed settings, see Chapter 5 Menu on
page 22.
Press Picture to access the picture setting menu.
Press Info to access projector information.
4. Basic Operation 19
Runco CL-710/ CL-710LT User’s Manual
Selecting Input Source
When this unit is turned on, it will search for the
input source you selected last time.
■ You may select the input source directly on the
remote control.
■
PIP/ PBP function
■
■
■
■
■
■
■
■
■
20
Press the PIP button to enable the PIP function
For PIP purposes, there are two groups of inputs
separated by their display modes:
Video Group: Video, S-Video and Component Y/CB/
CR inputs
Graphic Group: HDTV input and Computer input.
The PIP can show one input from the Graphic Group
within one input from the Video Group, or show one
input from Video Group within one input from the
Graphic Group.
Press the PIP button to switch to the main window
or turn off PIP function.
Select the input source of main window by pressing
the INPUT button.
Press the ACTIVE button to switch to the active
window. You can change the input signal setting in
active window.
Press PIP+ or PIP- to adjust the size of PIP window.
Adjust the position of the PIP window with the
ARROW keys (c,e,d,f).
Press PBP to enable the PBP function.
4. Basic Operation
Runco CL-710/ CL-710LT User’s Manual
Turning off the Power
■
■
■
■
■
■
Press the OFF key on the remote control to turn
off the unit.
The POWER LED will blink green and the fans will
speed up for a quick cool down. The projector
will not respond to any command for 90 seconds.
The POWER LED will light solid orange once the
cooling down cycle has completed.
After turning off the unit, the POWER LED will
blink green and the fans will operate at high speed
for 90 seconds.
Fans will run for three minutes to cool.
You may turn the projector back on after the first
90 seconds.
4. Basic Operation 21
Runco CL-710/ CL-710LT User’s Manual
5. Menu
Using the Menu
This unit is equipped with an on-screen display (OSD) menu for making various adjustments and settings.
There are four different menu languages; see page 24 Language setting for more details.
Press the Menu button to turn on /off the on-screen display menu.
Use the ARROW buttons (c,e,d,f) to select the menu or to make various adjustments.
■ Press the Enter or f button to enter the setting of items in the menu, or press the Exit button to leave and save
the setting of items in the menu.
■
■
Main Menu
Runco CL-710
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
----------------------Aspect Ratio
Options
Setup
Source selection and picture quality adjustments
Aspect ratio selection
Option selection
Setup selection
When the Menu button is pressed on the remote control, the main menu will appear on-screen. An example of the
main menu is shown above. Use c or d button to move the item you want to choose and then press the Enter or f
button.
The active source is indicated by an arrow ( > ) to the left of the source; note that in the example above, Video is the
current source.
22
5. Menu
Runco CL-710/ CL-710LT User’s Manual
Picture Quality Adjustments
Runco CL-710
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
----------------------Aspect Ratio
Options
Set Up
Adjustment
Brightness
Contrast
Color
Tint
Sharpness
Filter
Temperature
Store
Recall
To access the picture quality adjustments, press Menu, highlight the active source (indicated by the arrow) and press
Enter or f. The picture quality sub-menu will then appear (see above).
To make an adjustment to a particular function, highlight the function with the c or d arrow button and press Enter
or fto activate a scroll bar for that adjustment.
To enter into the memory selection menus, use Store and Recall menus to save and load three different memories.
There are three memories: Memory 1, Memory 2 and Memory 3.
Aspect Ratio
Runco CL-710
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
----------------------Aspect Ratio
Options
Set Up
Adjustment
> Anamorphic (16:9)
Standard (4:3)
Letterbox
Virtual Wide
There are four aspect ratios available that can be selected for video signal inputs.
16:9 Screens:
■
ANAMORPHIC: The image is compressed vertically, but anamorphic software will appear properly
proportioned. This is best suited for use with 16:9 DVD's.
Active Image Area
5. Menu 23
Runco CL-710/ CL-710LT User’s Manual
■
4 x 3: The input signal will be scaled to fit in the center of the 16:9 screen.
Active
Image Area
■
LETTERBOX: The image in the Letterbox mode will be stretched vertically, and the top and bottom portion
'blanked off'. This ratio is best suited for LaserDisc movies or non-anamorphic DVD's.
Active Image Area
■
VIRTUAL WIDE: A 4:3 image is transformed into a 16x9 image to allow the user to watch SDTV on their
widescreen.
Options
Runco CL-710
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
----------------------Aspect Ratio
Options
Set Up
Options
> Reset Adjustments
Language
Picture Orientation
Logo Light
Sleep Timer
Lamp Hours
OSD Position
PC & HD Adj.
Press Enter on selected feature to open the adjustment menu.
Reset Adjustments: Use this function to reset all values of the current source back to factory default.
Language: There are 4 different menu languages are available: English, Spanish, French and German.
Picture Orientation: The projector could be installed on a ceiling or behind a screen, or with one or more mirrors.
There are four settings: FLOOR FRONT, CEILING FRONT, FLOOR REAR, and CEILING REAR.
Logo Light: To turn on or off projector logo light.
24
5. Menu
Runco CL-710/ CL-710LT User’s Manual
Sleep Timer: To setup auto off minutes. The setting timer is from 10 minutes to 3 hours.
Lamp Hours: To check for total time lamp age.
OSD Position: To adjust horizontal and vertical positions of OSD.
PC & HD Adj.: The following settings are only available with a PC or DTV RGB signal. There is no position adjustment
when using DVI-D signal.
■
AUTO: Adjusts the phase, frequency and position automatically.
■
FREQ.: Adjusts the frequency of the signal.
■
PHASE: Adjusts the phase of the input signal.
■
H. POS.: Adjusts the horizontal position of the image.
■
V. POS.: Adjusts the vertical position of the image.
Setup
Runco CL-710
> Video
S-Video
Component
Component HD
RGB HD
DVI-I
----------------------Aspect Ratio
Options
Setup
Setup
> Keystone
Blue Image
White Balance
Reset Lamp Timer
Background Color
The Setup menu is passcode protected and for the use by Runco personnel only. Many of the adjustments available in
this section are intended for use by trained service personnel only. If you are having difficulty with one of these items,
please contact your Runco Dealer for service.
All items below which are printed in italic are intended for service personnel only. Non-italic items can be modified by
the projector owner.
The CL-710 has four memory settings for color temperature. Three of these settings are factory set to defalt as
follows:
Temp 1 -- 5400 kelvin
Temp 2 -- 6500 kelvin
Temp 3 -- 7500 kelvin
The Temp 4 memory is installer adjustable and can be used to create custom settings. A passcode must be entered in
order to change this setting. There are nine adjustable "white balance" parameters available for the Temp 4 setting.
Once the desired adjustments have been entered, selecting "store" will save these custom settings into the "Temp 4"
memory position.
Keystone: Corrects the trapezoidal distortion as a result of the angle of projection (-12° ~ +12°). This can correct for up to +/12 degrees of offset.
Blue Image: This makes the red and green turn off.
5. Menu 25
Runco CL-710/ CL-710LT User’s Manual
White Balance: To adjust grey scale.
White Balance
Red Gamma
Green Gamma
Blue Gamma
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Store
Adjust the Gamma Curve
Adjust High End
Adjust Low End
Reset Lamp Timer: Use this function to reset lamp usage counter. Reset only if you replace a new lamp.
Background Color: To adjust background color to blue or white.
26
5. Menu
Runco CL-710/ CL-710LT User’s Manual
6. Additional Information
Warning Message
It is normal for lamp to be darker when this unit
has been used for a period of time.
■ " Lamp life is expired ! Please change a new lamp.
And reset the lamp timer" message will be
displayed for 30 seconds on the screen if the lamp
has operated for 950 hours.
■
■
" Please change the lamp, Lamp will exceed its
lifetime after (hours):" message will be displayed
on the screen for 30 seconds for each time turning
on, if the lamp has operated for 980 hours. And
the number will count down continuously.
"Please change the lamp !" message will display on
the screen all the time and the POWER LED will
blink in orange and green sequentially if the lamp
has operated for more than (1,000) hours.
■ The power will turn off automatically after 10
minutes.
Lamp life is expired !
Please change new lamp
And reset the lamp timer
Please change the lamp !
Lamp will exceed its
lifetime after (hours):
■
Please change the lamp !
Replace the Lamp (Contact your Runco Dealer)
1. Loosen the screw of
front lamp cover
2. Take off the front lamp
cover.
2
1
3. Loosen the two
screws of lamp
module.
4. Pull out the lamp
module horizontally.
5. Insert the new lamp
module into this
projector
horizontally until it
is securely in place.
6. Tighten the two screws
of lamp module.
6. Additional Information 27
Runco CL-710/ CL-710LT User’s Manual
7. Put on the front
lamp cover.
8. Tighten the screw of
front lamp cover.
9.
Turn on the power and
go into the Set Up menu
to reset the "Lamp
Timer" item.
Troubleshooting
Problem
Possible Cause
Remedy
This unit does not
turn on.
There is no power from power cable.
Plug the power cord into the AC inlet on the
rear of this unit, and plug the power cord into
to the power inlet.
The power switch is not turned on.
Turn on the power switch.
Turn on this unit again within the
cooling down procedure.
Wait this unit complete the cooling down
procedure.
Front lamp cover is not attached well.
Correctly attach the front lamp cover.
The front lamp cover is not correctly
attached.
Correctly attach the front lamp cover.
This unit is not correctly connected to
the input source device.
Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the input
keys: Video, S-Video, Component, Component
HD, RGB HD and DVI-I on the remote control.
POWER LED or LAMP LED blinking.
Please contact your Runco dealer for
assistance.
Image is unstable
The connection cables are not
connected to this unit.
Correctly connect the cables to the
appropriate terminals.
Picture is blurred
The projection lens is not correctly
focused.
Adjust the focus of projection lens with the
focus ring.
This unit and the screen are not placed
squarely. (90 degree)
Adjust the projection angle and direction, and
the height of this unit.
Remote control does
not work correctly
The batteries are exhausted.
Replace both batteries with new ones.
LAMP LED blink in red
The front lamp cover is not correctly
attached.
Correctly attach the front lamp cover.
The cooling fan does not work well.
Please contact your Runco dealer for
assistance.
The temperature inside this unit is
extremely high.
Check that the ventilation holes are not
blocked.
The lamp has exceed its specified
usage hours.
Replace the lamp with a new one.
The lamp has burned out.
Replace the lamp with a new one.
No picture
POWER LED blink in
orange and green
sequentially
28
6. Additional Information
Runco CL-710/ CL-710LT User’s Manual
Specifications
CL-710/ CL-710LT Specifications
Projector Type:
Digital Light Processing™ (DLP™), Single HD-2 DMD Chip
Native Resolution:
1280 x 720, (16:9)
Aspect Ratios:
4:3, Letterbox, 16:9, Anamorphic, Virtual Wide
Video Standards:
NTSC, PAL
DTV Compatibility:
480p, 720p, 1080i
Scan Frequency:
Horizontal: 15-80 kHz
Vertical: 50-100 Hz
Recommended Width: 72-96 in.
Maximum Width: 200 in.
Picture Size (16:9 Screen):
Throw Distance
(Factor x Screen Width):
CL-710: 1.40 to 1.60/ CL-710LT: 1.85 to 2.40
Please refer to page 11 to page 14.
Light Output:
1000 ANSI Lumens*
CSMS** Specifications:
Home Theater Calibration:
489 ANSI Lumens
18.1 Foot-Lamberts (fL)
Contrast Ratio:
1800:1
CSMS** Contrast Ratio: 156:1
Lamp:
210W
Lamp Life:
1000 hours @ 6500o Kelvin
Inputs:
(1) Composite Video, (1) S-Video,
(1) RGB/Component (via BNC),
(1) RCA Component Video,
(1) DVI w/ HDCP, (1) RS-232
Memories:
21 memories
12V Output:
Max .250 Amp, active when the projector is on
Power Requirements:
100-240V AC, 50/60 Hz, 310 watts
Operating Environment:
41°- 95° F, (5°- 35° C), 20%-80% Humidity (non-condensing)
Dimensions (w/out feet):
Width: 16.15 in. (410.16 mm),
Depth: 14.56 in. (369.71 mm),
Height: Without feet 5.3 in. (134.62mm)
with feet 5.8 in. (148.62 mm)
Weight: 22 lbs. (10 kg) (includes lens)
Regulatory Approvals:
UL, CSA, GS-TUV, CCIB, CB,
FCC, CE, VCCI and C-Tick
Limited Warranty:
Projector: (2) Two year parts and
labor from the date of
delivery to the end user
Lamp Warranty: 1000 hours or
(6) six months, which ever comes first.
6. Additional Information 29
Runco CL-710/ CL-710LT User’s Manual
*ANSI Lumen specification:
This is the typical projector luminosity (brightness) specification found in most sales literature. This measurement is
included in RUNCO literature to allow for direct comparison with other manufacturer's projectors. These
measurements can be taken at 9,000 to 13,000 degree Kelvin to get expected performance data when the projector is
used in professional, commercial, and industrial displays.
**CSMS Home Theater Calibration ANSI Lumen Specification:
These measurements are taken from the projector as setup in a home theater environment. The projector is calibrated
to ISF specifications including setting the color temperature to 6500 degree Kelvin, the standard for reproducing video.
**CSMS Home Theater Calibration foot-Lambert (fL) Specification:
This is the unit of measurement used in commercial movie theaters to express image brightness. The Society of Motion
Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using
an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image
brightness in Digital Cinema theaters using DLP(tm) technology. The foot-Lambert is dependant on screen size, screen
gain, and projector light output.
All measurements are made at RUNCO to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650
SpectraColorimeter and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech
130, 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6500 o Kelvin and has a
minimum of 150 hours of usage.
30
6. Additional Information
Runco CL-710/ CL-710LT User’s Manual
Dimensions
Unit: in. (mm)
6. Additional Information 31
Runco CL-710/ CL-710LT User’s Manual
RS-232 Setup
PC Out Adapter
Baud Rate: 115200 or 9600
1. Connect D-Sub 9-pin female to RJ-11 adapter (not
included) to Com port on PC.
Parity: None
2. Connect RJ-11 to Projector.
Data Bits: 8 Bits
Stop Bits: 1 Bit
RJ-11 to D-Sub 9-pin (not included)
Flow Control: None
RS-232C Control Codes
Code
X01
X02
X03
X04
X10
X11
X12
X13
X14
X15
X16
X20
X21
X22
X23
X24
X25
X35
X36
X37
X38
X40
X41
X42
X46
X47
X48
X49
X55
X56
X57
X60
X61
X62
X85
X90
X91
X92
X93
X94
X95
Function
Power On
Power Off
Message On
Message Off
Menu (arrow key)
Enter (arrow key)
Exit (arrow key)
Up (arrow key)
Down (arrow key)
Left (arrow key)
Right (arrow key)
Switch to Composite input
Switch to S-Video input
Switch to Component input
Switch to D-Sub _PC input
Switch to YPBPR input
Switch to BNC_PC input
Anamorphic
Standard
Letter box
Virtual Wide
Load memory 1 settings
Load memory 2 settings
Load memory 3 settings
Load default of current source
Save memory 1 settings
Save memory 2 settings
Save memory 3 settings
Switch active source
Picture in picture display
Picture in picture display
Switch language - English
Switch language - French
Switch language - Spanish
PC Input - auto
Image orientation - floor front
Image orientation - ceiling front
Image orientation - floor rear
Image orientation - ceiling rear
Back light on
Back light off
RS-232 For D-Sub 9-pin (not included)
D-Sub 9-pin female
2
3
5
1, 4, 6, 7, 8, 9
Details
TxT
RxD
Ground
NC
5
4
9
3
8
1
2
7
6
D-Sub 9-pin female
Warning: During initial turn on and turn off of the
projector, this unit will not accept RS-232 codes for 20
seconds.
RS-232 For RJ-11 (not included)
4-pin RJ-11
2
3
1, 4
Details
TxT
RxD
Ground
Yellow
Green
Green
Yellow
1
2
3
4
Black
Red
Black
Red
NOTE:
1. All codes are in the ASCII format.
2. A carriage return is required after each command.
6. Additional Information
32
RUMA-010100 rev 7-03
Runco International . 2900 Faber Street . Union City, CA 94587 . ph (510) 324-7777 . fax (510) 324-9300 . www.runco.com
Download PDF
Similar pages