DMP 7872 Touchscreen - Complete Security Systems

INSTALLATION GUIDE
Models 7872 and 7873
Graphic Touchscreen Keypads
CURRENT
82
HI LO
TODAY
98 77
WEDNESDAY
98 77
HI LO
© 2015 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
DMP Keypad Features
DMP Graphic Keypads offer flexible features and functionality in a stylish design.
Each keypad provides:
• AC Power/Armed LED
• Full color touchscreen display
• Internal speaker
• Simple harness connection to 4-wire keypad bus
• Micro SD for customized logo
• Icon-driven operation
The Model 7872 keypad provides four fully programmable Class B, Style A,
supervised, power limited protection zones and a built-in proximity card reader
designed to read DMP/HID proximity credentials.
The Model 7873 keypad provides four fully programmable Class B, Style A,
supervised, power limited protection zones and a built-in proximity card reader
designed to read DMP/HID proximity credentials. The Model 7873 keypad also
provides a door strike relay and allows Wiegand input from external card readers.
MON 5:35 AM
Panic
CURRENT
Chime
82
TODAY
HI
LO
98 77
Check-in
Reset
HI
LO
WEDNESDAY 80 74
ARMED
Figure 1: Keypad Main Screen
7800 Series Keypad Installation Guide
1
Touchscreen Display
The 7800 Series keypads have an integrated LCD touchscreen user interface. The
display can be set up to display a custom logo image on the main screen. See the
Custom Dealer Logo section below. The display can also be programmed to turn
off (blank screen) during periods when the keypad is not in use. See Backlighting
Brightness under End-User Options.
Warning: DO NOT use any sharp objects to operate the touchscreen such as a pen or
pencil.
Cleaning the Touchscreen Display
Select the keypad option from the main carousel menu until it glows and clean the
touchscreen using a water dampened soft, lint-free cloth. Apply the water onto
the cloth, do NOT apply directly onto the touchscreen. After cleaning, wipe the
touchscreen dry with a soft, lint-free cloth. Touch the back arrow before returning to
the main screen.
Micro SD Card
The 7800 Series keypads provide a spring-loaded Micro SD card slot on the right edge
of the keypad housing. This is used to load a custom logo onto the main screen. Insert
the Micro SD card straight in, with the contacts facing the wall, pressing in until a
click occurs from the spring mechanism. To remove the Micro SD card, gently press in
to allow the spring to eject the card. Grasp the edges of the card with two fingers
and remove.
MON 5:35
AM
CURRENT
82
TODAY
HI
Panic
Micro SD
Card Slot
Chime
LO
98 77
Check-in
Figure 2: Micro SD Card Slot
80
WEDNESDAY
Reset
74
Custom Dealer
Logo
ARMED
To display a custom dealer logo
on the main screen, contact DMP Marketing at
1-800-641-4282 or privatelabel@dmp.com for information. To add a custom dealer
logo, see the Dealer Logo option under Installer Options menu.
HI
LO
Installing the Keypad
Building Wall
Graphic
Keypad
All DMP keypad housings are designed to easily install on any
single‑gang switch box or flat surface. Figure 6 shows the keypad
Insert small
screwdriver and
housing base mounting hole locations.
lift to remove
cover.
Remove the Cover
Do not twist.
The keypad housing is made up of two parts: the cover, which
contains the circuit board and components, and the base. Use the
following steps and figures to separate the keypad cover and base:
1. Insert a flat screwdriver into one of the slots on the bottom of
the keypad and gently lift the screwdriver handle toward you
Figure 3:
while pulling the halves apart. Repeat with the other slot.
2. Using your hands, gently separate the front from the base and Removing the
Keypad Cover
set the cover and components aside.
2
7800 Series Keypad Installation Guide
Harness Wiring
Y/W
Figure 5 shows wiring harness assignments. Observe wire colors when connecting the
red, yellow, green, and black wires to the keypad bus. Connect red to panel terminal
7, yellow to terminal 8, green to terminal 9, and black to panel terminal 10. Use 1k
Ohm EOL resistors, DMP Model 311, on keypad zones 1 through 4.
The 7872/7873 keypads are supplied with a 12-wire data bus/zone harness. Four
wires connect to the keypad bus. The remaining eight wires are for the four zone
inputs: two wires for each zone.
The 7873 keypad comes with one 5-wire output/reader
J5
R
harness for connection of external reader/door strike and is
inserted into the J4 keypad terminal.
When replacing a 32-character keypad that uses a standard
12-position harness, the 300-7800-12ADPT 12-position wire
harness adaptor is available to adapt the larger connector to
the smaller 7800 Series connector (J5) without the need to
splice wires.
Note: Do not remove the PCB from the keypad housing to
install the wiring harness. Firmly grasp the wires near the
Figure 4: Installing the
base and hold the outside edges of the keypad housing. Line
Wiring Harness
up the red and yellow wires with the guides on the board to
insert the connector into the J5 keypad terminal. See Figure 4
for example.
Additional Power Supply
If the current draw for all keypads exceeds the panel output, provide additional
current by adding a Model 505-12 auxiliary power supply. Connect all keypad black
ground wires to the power supply negative terminal. Run a jumper wire from the
power supply negative terminal to the panel common ground terminal. Connect all
keypad power (+12 VDC) wires to the power supply positive terminal. Do NOT connect
the power supply positive terminal to any panel terminal. Refer to the 505-12 Power
Supply Installation Guide (LT‑0453).
7873 Back
Zones 1 to 4
7872 / 7873 Keypads
Yellow/White
– Zone 4
White/Yellow
J5
V
External Reader/Door Strike
7873 Keypad
– Zone 2
Brown/White
White/Brown – Zone 1
All Keypads
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
J4
R
G/W
Red/White
White/Red
Y/W
Orange White
White/Orange– Zone 3
1K EOL
Violet – Door Strike Normally Closed
Gray – Door Strike Common
Orange – Door Strike Normally Open
White – Connect Reader Data 1
Green/White – Connect Reader Data 0
1K EOL
1K EOL
1K EOL
Figure 5: Keypad Back Showing Wiring Harness Assignments
7800 Series Keypad Installation Guide
3
Card Readers
When a proximity credential is presented to an internal or external reader, a beep
tone is heard and the Power/Armed LED blinks. This provides both an audible and
visual acknowledgement of the credential read.
Internal Access Control Reader
The 7873 and 7872 keypads provide a built-in proximity card reader designed to read
DMP/HID 1300 Series proximity credentials.
External Access Control Reader
To accept Wiegand data input from other external card readers, connect a
12 VDC external reader to the 7873 keypad. Connect the Red and Black power wires
from the reader to the power wires from the panel. These connect in parallel with
the keypad power wires. Connect the Reader (Data 1) wire to the White wire on the
5‑wire keypad harness. Connect the Reader (Data 0) wire to the Green/White wire on
the 5‑wire keypad harness. See Figure 6.
Surface and Backbox
Mounting Holes
Keypad Back
Zones 1 to 4
7872 / 7873 Keypads
Yellow/White
– Zone 4
White/Yellow
External Card
Reader
Orange White
– Zone 3
White/Orange
Red/White
White/Red
– Zone 2
Brown/White
– Zone 1
White/Brown
All Keypads
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
1K EOL
1K EOL
1K EOL
1K EOL
Black
Green
Yellow
Red
Violet – Door Strike Normally Closed
Gray – Door Strike Common
Orange – Door Strike Normally Open
White – Connect Reader Data 1
Green/White – Connect Reader Data 0
Black – Ground
Red – Keypad Power
Figure 6: 12 VDC Reader Wiring
Door Strike Relay Specifications
The 7873 keypad provides one internal programmable Form C single pole, double
throw (SPDT) relay for controlling door strikes or magnetic locks. Three wires on the
5-wire harness, Violet (N/C), Gray (Com), and Orange (N/O), allow you to connect
devices to the relay. The Form C relay draws up to 15mA of current and the contacts
are rated for 1 Amp at 30 VDC maximum, resistive.
4
7800 Series Keypad Installation Guide
Keypad Back
Zones 1 to 4
7800 Series Keypads
Brown/White – Zone 1
White/Brown
Red/White
White/Red
– Zone 2
Orange White – Zone 3
White/Orange
Wiring the
333 Suppressor
Suppressor is
included with the 7873 keypad. If
Violet – N/C
the
device being controlled by the
All Keypads
Gray – Common
Black
– Ground
relay
is connected to the1K EOL
N/O and
1K EOL
Orange – N/O
Green
– Receive Data
Model 333
C wires,
install the suppressor
on
1K EOL
Supressor
Yellow
the– Send
N/OData
and C wires. If the
device is
White – Connect
1K EOL
Redconnected
– Keypad Power to the N/C and
C wires,
Reader Data 1
install the 333 on N/C and C wires.
Green/White –
Refer to Figure 7.
Connect Reader
Data 0
Door Strike Relay Operation
As soon as the user code sent
from the reader is verified by the
DMP 505-12
panel, the keypad door strike relay
+
–
Power Supply
activates for 5 seconds. During this
Magnetic Door Lock
time, the access door connected
to Zone 2 must be opened to start
the programmed entry/exit timer
Figure 7: 5-wire Harness/Suppressor Installation
and zone Bypass (Soft-Shunt™) if
programmed and used.
Note: The 5-second door strike is panel programmable when the keypad is used on an
XR100/XR500 or XR150/XR350/XR550 Series panel. Refer to the panel programming
guide as needed.
Closed
Normally
Common
Normally
Open
Yellow/White
One Model
– Zone 4333
White/Yellow
Zone 2 Door Contact with Bypass (Soft-Shunt)
If the door being released by the 7873 keypad is protected, you can provide a
programmed bypass time by connecting its contact to Zone 2 (White/Red pair) on the
keypad and enabling the Bypass feature. See ZONE 2 BYPASS later in this document.
Door contacts may be N/C or N/O.
Zone 3 Request to Exit
You can also connect a N/O PIR (or other motion sensing device) or a mechanical
switch to Zone 3 (White/Orange pair) on the 7873 keypad to provide request to exit
capability. See ZONE 3 EXIT later in this document. When Zone 3 shorts, the keypad
relay activates for between 5 and 250 seconds. This REX time is programmable with a
default of 5 seconds. See ZONE 3 REX STRIKE TIME later in this document.
During this time, the user can open the protected door to start the programmed
Bypass entry/exit timer. If the door is not opened within 5 seconds, the relay restores
to its locked state.
Note: A Zone 3 Request to Exit is inhibited for 3 seconds after the keypad reads a card
and a door strike occurs. This is to allow area entry and pass under a REX PIR.
Keypad Backlighting
The touchscreen illuminates at the maximum brightness any time the display is
pressed. During an alarm condition, the touchscreen turns Red. When all alarm
conditions are cleared from the display, the keyboard, logo, and the user‑selected
brightness is restored.
AC Power/Armed LED Operation
The LED indicates the Power and Armed status of the panel. Depending on the
operation, the LED displays in Red or Blue as listed in the table.
7800 Series Keypad Installation Guide
5
Color and Activity
Blue Steady
Blue Blinking
No Light
Red Steady
Red/Blue Alternate
Red Blinking
Operation
Panel Disarmed, AC Power OK, Battery OK
Panel Disarmed, AC Power OK, Battery Fault
Panel Disarmed, AC Power Fault, Battery OK
Panel Armed, AC Power OK, Battery OK
Panel Armed, AC Power OK, Battery Fault
Panel Armed, AC Power Fault, Battery OK
Select Areas
Select Area 1 Select Area 2 Select Area 3 Select Area 4
There are four Select Areas in the display as
seen in Figure 8. These Select Areas are one of
the features that make the system so easy to
operate. They allow you to make selections by
pressing the area over each key, icon, or other
selection to operate the keypad.
Warning: DO NOT use any sharp objects to
operate the touchscreen such as a pen
or pencil.
Panic Icons
1ABC
5MNO
9YZ
2DEF
6PQR
0
3GHI
7STU
4JKL
8VWX
CMD
Figure 8: Touchscreen Select Areas
Optional Panic functions allow users to send
Police, Emergency, or Fire reports to the central station (See Figure 9). You must
enable the Panic function in Installer Options in order to use the Panic Icons. See
Programming Keypad Options later in this document.
Press the panic icon in the carousel menu to bring up the Panic Options menu. This
icon can be seen in Figure 10 below. Press the panic menu icon for 2 seconds until a
beep is heard. At the beep, the panel sends the following zone alarm reports to the
central station:
Panic - Zone 19 + Device Address
Emergency - non-medical - Zone 29 + Device Address
Fire - Zone 39 + Device Address
MONITOR ON
PRESS AND HOLD BUTTON TO SEND
PANIC OPTIONS
Panic
Chime
NOW
POLICE
EMERGENCY
Check-in
FIRE
TUE
Reset
DISARMED
Figure 9 and Figure 10: Graphic Keypad Panic Icons
6
7800 Series Keypad Installation Guide
Internal Speaker Operation
All keypads emit standard tones for screen presses, entry delay, and system alerts.
The speaker also provides distinct burglary, fire, zone monitor, and prewarn cadences.
The keypads provide an alternate prewarn with alarm cadence that occurs when the
status list displays a zone alarm.
End-User Options
All keypads provide three keypad adjustments the end-user can make through a User
Options Menu. The user can also view the keypad model number and address.
Scroll through the carousel menu and press the Options icon until it glows. The screen
displays the available options shown below. See Figure 11 for example.
Backlighting Brightness
Set the backlight illumination and AC Power/Armed LED brightness level. In the
touchscreen display below SET BRIGHTNESS, press the left < to lower and the right
> to raise the backlight brightness. If the brightness level is lowered, it reverts to
maximum intensity whenever the screen is pressed during normal operation. If the
screen is not pressed, and the speaker has not sounded for 30 seconds, the userselected standby brightness level restores.
Internal Speaker Tone
Set the keypad speaker tone for screen presses. At the SET TONE display, use the left
< to lower the tone and the right > to raise the tone.
Internal Volume Level
Set the keypad speaker volume level for screen presses, entry delay, and zone
monitor conditions. During alarm, entry delay, and trouble tone conditions, the
volume is always at maximum level. Use the left < to decrease the keypad volume
and the right > to increase the volume.
Model Number
The LCD displays the keypad model number and firmware version and date in the top
right corner of the screen. The user cannot change this information.
MODEL NUMBER 7800 V100 111912
BRIGHTNESS
TONE
VOLUME
INSTALLER
OPTIONS
Figure 11: Options Screen
7800 Series Keypad Installation Guide
7
Installer Options Menu
Keypad Options and Keypad Diagnostic menus allow installing and service technicians to
configure and test keypad operation.
Access the Installer Options Menu
Access the Options menu through the carousel menu. While in the Option display, press the
Installer Options icon and enter the code 3577 (INST) at the keypad and press CMD.
The Options menu allows you to set the keypad address, select Supervised or Unsupervised
mode, selectively enable the Panic keys, Bypass, Request-to-Exit, and set entry
card options.
Note: All programming options display on all keypad models, however, actual operation for
some programming options is restricted to the appropriate model.
Programming Keypad Options
Keypad Options (KPD OPT)
KPD KPD
To program keypad options, press KPD OPT.
OPT DIAG STOP
CURRENT KEYPAD
ADDRESS: 01
Keypad Address
Set the keypad address from 01 to 08 with the XT30/XT50,
01 to 08 with the XR100 and XR150 Series, 01 to 16 with the
XR500 Series, and 01 to 16 with the XR350/XR550 Series.
The default address is set at 01. To change the current
address, press the address display and enter the new
address. It is not necessary to enter a leading zero for
addresses 01 to 09.
Keypad Type
KEYPAD MODE:
Configure the keypad for either Supervised or Unsupervised
SUP *UNSUP operation. Keypads with zones connected to them must be
supervised and cannot share an address with other keypads.
Unsupervised keypads can operate together sharing the same
address. Zones cannot be used on unsupervised keypads.
To change the current setting, press the SUP or UNSUP. An
asterisk appears next to the selected option.
Note: Unsupervised addresses cannot be used when Device
Fail Output has a programmed value other than zero.
DEFAULT KPD MSG:
Default Keypad Message
Enter a custom message of up to 16 characters to appear on
the keypad display top line whenever that line is not used
for any other purpose. Press any Select area to clear the
current message and enter a new custom display.
Arm Panic Keys
ARM PANIC KEYS:
Use this option to configure the Panic Icons. To enable
*PN*EM *FI
or disable a Panic Icon, press the icon name: PN (Panic),
EM (Emergency), and FI (Fire). Once the panic icon is
enabled, an asterisk displays next to the description and the
respective Panic icons display for the user. Refer to the Panic
Icon Options section in this document.
8
7800 Series Keypad Installation Guide
ACTIVATE ZONE 2
BYPASS: NOYES
ZONE 2 BYPASS
TIME:40
Zone 2 Bypass (Soft-Shunt)
Select YES to enable the Bypass option on zone 2 as
described earlier in this document. This zone provides the
bypass for door contacts. This zone must be programmed
into the panel.
Zone 2 Bypass (Soft-Shunt) Time
Enter the number of Bypass seconds to elapse before the
bypass timer expires. Range is from 20 to 250 seconds. Press
the display to enter the number of seconds. Once the door
strike relay is activated, the user has 5 seconds to open the
door connected to zone 2. The zone is then bypassed for the
programmed time or until the contact restores to normal.
Ten seconds before the Bypass entry/exit time expires, the
keypad beeps once every second. If the door remains open
when the timer expires a zone open/short is sent to the
panel for Zone 2. The default is 40 seconds.
Figure 12 shows how the Bypass works using the default 40
second timer.
5 Second
Strike
MON 5:35 AM
Dealer Logo
Panic
Chime
CURRENT
82
TODAY
HI
LO
At 30 seconds,
40
the keypad beeps
Seconds
if door is still open.
Check-in
98 77
Fire Reset
HI
LO
WEDNESDAY 80 74
40-Second Bypass
and entry/exit timer.
DISARMED
End of
timer.
A zone fault is indicated
if door is still open.
Figure 12: Door Strike Relay Operation Time Line
Relock on Zone 2 Fault? (7873 only)
RELOCK ZONE 2
Select NO to leave the relay on when Zone 2 faults to an
FAULT: NOYES open or short condition during Bypass. Select YES to turn the
relay off when Zone 2 faults open or short during bypass.
The default is NO.
Zone 3 REX (7873 only)
ACTIVATE ZONE 3
Select YES to enable the Request to Exit feature on zone
EXIT? NOYES 3. When zone 3 shorts, the keypad relay activates. During
this time, the user can open the protected door to start
the programmed Bypass entry/exit timer. If the door is not
opened within the time programmed in the Zone 3 REX
Strike Time, the relay restores the door to its locked state.
No panel programming is required.
Zone 3 REX Strike Time (7873 only)
ZN 3 REX STRIKE
TIME: 5
Enter the number of REX seconds to elapse. Range is
from 5 to 250 seconds. Press the display to enter the
number. The default is 5 seconds.
7800 Series Keypad Installation Guide
9
Number of User Code Digits
NO OF USER CODE
DIGITS: 5
The keypad recognizes user codes from 4 to 10 digits
in length. Press the display to enter the user code digit
length being used by the panel. Default is 5.
When searching the bit string for the user code, the digits
are identified and read from left to right.
ALL?: NOYES Arming/Disarming Wait Time
Select the number of seconds (1-9) the keypad should
DELAY: 2
wait when an area system displays ALL? NO YES during
arming/disarming or a HOME/SLEEP/AWAY system waits
during arming only. If NO or YES, or HOME, SLEEP, or
AWAY is not manually selected before the delay expires,
the keypad automatically selects the YES or the AWAY
key. Enter zero (0) to disable this feature. The delay also
occurs when any credential is presented for arming the
HOME/SLEEP/AWAY system.
Card Options
CARD OPTIONS
Select DMP to indicate the reader sends a 26-bit DMP
DMPCUSTOM data string. To save the DMP option, press DMP and then
press COMMAND. Select CUSTOM if using a non-DMP
credential.
To select CUSTOM press the right side of the display.
When CUSTOM displays, press COMMAND.
Default is DMP.
Custom Card Definitions
WIEGAND CODE
Card Options
Wiegand Code Length
LENGTH
26
When using a custom credential, enter the total number
of bits to be received in Wiegand code including parity
bits. Press the display to enter a number between 0-255
to equal the number of bits. Default is 26 bits. Typically,
an access card contains data bits for a site code, a user
code, and start/stop/parity bits. The starting position
location and code length must be determined and
programmed into the keypad.
01110101101101010001100111
First Bit
Received
Position = 0
Site Code
Position = 1
Length = 8
User Code
Position = 9
Length = 16
Last Bit
Received
Position = 25
In this example the Wiegand Code Length = 26 bits.
Figure 13: HID 26-Bit Wiegand Data Stream Bit Location Example
10
7800 Series Keypad Installation Guide
SITE CODE: Site Code Position
Enter the site code start position in the data string. Press
POSITION
1
any select area to enter a number between 0-255. Press
COMMAND to save the entry. Default is 1.
SITE CODE: Site Code Length
Enter the number of characters the site code contains.
LENGTH
8
Press any select area to enter a number between 1-16.
Press COMMAND to save the entry. Default is 8.
USER CODE: User Code Position
Define the User Code start bit position. Press any select
POSITION
9
area to enter a number between 0-255. Press COMMAND
to save the entry. Default is 9.
USER CODE: User Code Length
Define the number of User Code bits. Press any select
LENGTH
16
area to enter a custom number. Custom numbers can only
be a number between 16-32. Press COMMAND to save the
entry. The default is the DMP value of 16.
Require Site Code
REQUIRE SITE
Press YES to use a site code, for non-DMP cards, and press
CODE: NO YES CMD to view the site code entry display. Default is NO.
In addition to User Code verification, door access is only
granted when any one site code programmed at the SITE
CODES entry option matches the site code received in the
Wiegand string. You can program up to eight three-digit
site codes.
Note: A card with a site code greater than three digits
cannot be used. Use only cards with three-digit
site codes.
Site Codes 1-4
SITE CODES 1-4
Enter site codes 1-4 (left to right separated by > sign).
> > > >
Press the > sign to add, delete, or change the site code.
Press COMMAND to save the entry.
Site code range is 0-999.
Site Codes 5-8
SITE CODES 5-8
Enter site codes 5-8 (left to right separated by > sign).
> > > >
Press the > sign to add, delete, or change the site code.
Press COMMAND to save the entry.
Site code range is 0-999.
No Communication With Panel
NO COMM WITH PNL
This option defines the relay action when communication
OFF
with the panel has not occurred for five seconds. Press
any select area to display CHOOSE ACTION.
The default is Relay Always Off.
Choose the No Communication with Panel action that
CHOOSE ACTION
is required.
OFF SITE ANY ON
Press OFF to choose [Default] (Relay Always Off) —
The relay does not turn on when any Wiegand string is
received. Off does not affect any REX operation.
7800 Series Keypad Installation Guide
11
CHOOSE ACTION
LAST
SYSTEM
AREA A/P H/A HSA
DEALER LOGO
ADDDELETE
ADDING LOGO
SURE? NOYES
DEALER INFO
ADD
DELETE
ADDING INFO
SURE? NOYES
12
ress SITE to choose (Accept Site Code) — Door access
P
is granted when the Wiegand site code string received
matches any site code programmed at SITE CODE
ENTRY. For details refer back to the REQUIRE SITE
CODE option.
Press ANY to choose (Any Wiegand Read) — Door
access is granted when any Wiegand string is received.
Press ON to choose (Relay Always On) — The relay is
always on.
Press the COMMAND key to display the next action.
Press LAST to choose (Keep Last State) — The relay
remains in the same state and does not change when
communication is lost.
After choosing the action, the NO COMM WITH PNL
option and the newly defined action display. Press
COMMAND to save the entry. Press the Back Arrow to
return to REQUIRE SITE CODE:.
System
Configure the keypad as the same system type selected
in System Options panel programming. Select HSA when
zones are assigned to Bedrooms for the Sleep area to
be active.
Dealer Logo
Use this option to add a custom dealer logo to the Main
Screen of the keypad. Prior to selecting ADD, insert
a micro SD card into the slot on the right side of the
keypad with the logo file. Select ADD to upload the file.
The keypad will display ADDING LOGO SURE? Select YES
to proceed. While the logo is being uploaded, the keypad
displays ADDING LOGO. ADDING LOGO COMPLETED
displays to confirm a successful upload.
Select ADD at the DEALER INFO prompt to include
information about the dealer when the logo is pressed on
the Main Screen. The keypad displays ADDING INFO SURE?
to confirm your selection. Press YES to proceed. While
the info is being uploaded, the keypad displays ADDING
INFO. ADDING INFO COMPLETED displays to confirm a
successful upload. Once dealer logo and information have
been successfully uploaded press in and release micro SD
card to eject.
Contact DMP Marketing at 1-800-641-4282 or
privatelabel@dmp.com for information about acquiring
a logo.
Note: For instructions on loading a Custom Dealer Logo to
the Main Screen of the keypad prior to being connected
to the panel, see Additional Programming; Preloading
Custom Dealer Logo and Information.
7800 Series Keypad Installation Guide
Carousel Z-Wave Items
The Z-Wave Carousel Items screen allows you to select
CAROUSEL Z-WAVE ITEMS
the Z-Wave options to be displayed in the Carousel
menu on the main screen. Press the item to select and
a check-mark displays. Press again to de-select. Items
for the Carousel include Lights, Doors, Thermostats,
and Favorites. Pressing CMD at the bottom of the
screen advances to the next screen and the Back Arrow
CMD
returns you to the previous option. Default is no items
Figure 14: Carousel Z-Wave
selected.
Items Screen
Shortcut Items
The Shortcut Items screen allows you to select
SHORTCUT ITEMS
additional menu items to be displayed in the Carousel
menu on the main screen. Press the item to select and a
check-mark displays. Press again to de-select. Items for
the Carousel include User Codes, Schedules, and Events.
Default is no items selected.
CMD
Select Z-Wave Edit to display the Z-Wave Edit icon on
the Lights, Doors and Thermostats screens. Select Edit
Figure 15: Shortcut Items
Favorites to display the Z-Wave Edit icon on the Favorites
Screen
screen. If NO is selected, the Z-Wave Edit icon will not be
displayed. For more information, see Z-Wave Edit
Icon below.
Z-Wave Edit Icon
The Z-Wave Edit icon is a small, pencil shaped, shortcut that
may be enabled and displayed in the lower left corner of the
Z-Wave Lights, Doors, Thermostats, and Favorites screens
accessed from the Carousel menu. This shortcuts allows the user
to add, edit or remove Z-Wave devices and Favorites. When the
icon is pressed on the Lights, Doors, or Thermostats screens, the
keypad prompts for a User Code. Enter a valid user code and
Z-WAVE SETUP? ADD LIST REMOVE displays. When the icon is
Figure 16: Z-Wave
pressed on the Favorites screen, the keypad prompts for a User
Edit Icon
Code. Enter a valid user code and FAVORITE NUMBER: - displays.
For more information on Z-Wave devices and Favorites please
see the panel user guide.
Select Language
The Select Language screen allows you to select the
SELECT LANGUAGE
language for text on the Home Screen and Carousel
Menu Screens. Press the item to select and a check mark
English
Spanish
displays. Only one language may be selected.
Default is English.
Note: The keypad does not translate information from the
panel that is displayed in the Keypad screen such as the
CMD
Status list.
MON 5:35 PM
Lights
Thermostats
Doors
Favorites
MON 5:35 PM
User Codes
Events
Schedules
Edit Z-Wave
Edit Favorites
MON 5:35 PM
Figure 17: Select Language
Screen
7800 Series Keypad Installation Guide
13
Restart Keypad
The Restart Keypad screen allows the installer to
restart the keypad to initiate a firmware update
from a Micro SD card.
MON 5:35 PM
RESTART KEYPAD
Press the button to restart the keypad.
RESTART
Updating Firmware using Restart
To load new firmware from an SD card, insert the card and
press RESTART. The keypad will restart, install, and restart
1. Insert a Micro SD card into the Micro SD Card
again. Do not remove the SD card or disrupt power during
this process.
Slot of a computer.
CMD
2. Locate and download the firmware update
RU file from dmp.com/dealer_direct and save
Figure 18: Restart Keypad
it to the root directory of the Micro SD card.
Screen
3. Insert the Micro SD card into the Micro SD card
slot on the right side of the 7800 Series keypad.
4. Enter the Installer Menu (3577), choose KPD OPT and press CMD to the new
Restart Keypad screen just after Select Language.
5. Press RESTART. The keypad will load the new firmware from the Micro SD Card
and then the keypad automatically restarts. Caution, do not remove the Micro
SD card or disrupt power during this process.
6. When the keypad restart is complete, remove the Micro SD card from the
keypad.
2GB
MICRO
SD
Accessing Keypad Diagnostics
If necessary, refer to Access the Options Menu earlier in this document.
KPD KPD
OPT DIAG STOP
Z1 OPEN
Z3 OPEN
Z2 OPEN
Z4 OPEN
INPUT WIEGAND
Keypad Diagnostics (KPD DIAG)
This option displays Zone Test.
Zone Test
This option allows the keypads to display the current
electrical status of the four protection zones. The status
is shown as OPEN, SHRT, or OKAY.
Note: The Zone Test displays on other keypads without
built-in zones, but is not operational.
Input Wiegand
This option tests the internal and external reader input
from proximity credentials. The display shows OKAY each
time a good proximity read is received.
Exiting the Installer Options
Press the CMD key until the display returns to the Installer Options screen. Select
STOP to exit the Installer Options function.
14
7800 Series Keypad Installation Guide
Additional Programming
The keypads allow users to present a proximity credential to the built-in proximity
reader. Users can also manually enter their user code into the keypad. The keypad
verifies the user code and its authority with the panel. Additionally, the 7873 keypad
activates the on-board Form C relay releasing a door strike or magnetic lock. To
provide added flexibility, the 7873 Keypads allow connection of an external Wiegand
output compatible reader.
Preloading Custom Dealer Logo Information
A custom dealer logo and dealer information may be added to the Main Screen of the
keypad prior to being connected to the panel. This procedure requires the use of a
separate 12 Volt power supply for the keypad. Use the following steps:
1. Connect the 12 Volt DC power supply to the keypad.
2. Power up the keypad and the keypad screen displays SYSTEM BUSY.
3. Press COMMAND to display ENTER CODE:.
4. Enter 3577 and press COMMAND to access the Installer Menu.
5. Press KPD OPT to access keypad options menu.
6. Press COMMAND until DEALER LOGO ADD DELETE displays.
7. Insert Micro SD card with dealer logo into the slot on the right side of the keypad.
8. Press ADD. Keypad displays ADDING LOGO SURE? YES NO.
9. Press YES to load dealer logo. Keypad displays ADDING LOGO.
10. When the dealer logo is successfully loaded the keypad displays
ADDING LOGO COMPLETE.
11. Press COMMAND to exit Dealer Logo menu.
12. Keypad displays DEALER INFO ADD DELETE.
13. Press ADD. Keypad displays ADDING INFO SURE? YES NO
14. Press YES to load dealer information. Keypad displays ADDING INFO.
15. When the dealer information is successfully loaded the keypad displays
ADDING INFO COMPLETE.
16. Press COMMAND to exit to Dealer Info menu.
17. Press Stop to exit Installer Menu.
18. Press in and release the micro SD card to eject
Note: If for any reason the logo or information fails to load the keypad displays
BAD FORMAT. Contact DMP Marketing at 1-800-641-4282 or privatelabel@dmp.com for
information about acquiring a logo.
Programming Cards into the System
Access the User Menu by pressing the Keypad icon in the carousel menu on the main
screen, then press CMD until MENU? NO YES displays.
From the User Menu, select USER CODES. Choose ADD. At the ENTER CODE: - display,
present the credential to the reader. The keypad works by reading the 4 to 10-digit
user code from the data sent by the access control reader. For more information,
refer to Entry Cards in the programming section of this document and the panel
User’s Guide section on adding, deleting, and changing user codes.
7800 Series Keypad Installation Guide
15
Proximity Credentials Compatibility
DMP Keypads with internal proximity readers are compatible with most standard
125Khz Prox credentials available from HID and all DMP proximity credentials. DMP
Keypads are not compatible with iClass.
There are custom and non-standard credentials from HID that are not compatible
with DMP proximity keypads. If you are using HID cards that have not been purchased
directly from DMP, it is recommended to thoroughly test the application fully before
installation. DMP does not guarantee compatibility with credentials not purchased
from DMP.
User’s Guide
This User’s Guide covers 7872 and 7873 keypads and contains three different sections:
Keypad Arming and Disarming, Keypad Door Strike, and Keypad Entry Delay. All of the
examples displayed assume that CLOSING CODE is YES in panel programming.
Note: Figures 18 through 20 show the user presenting their card to the keypad. When
an external reader is connected to a 7873 keypad, the user presents their card to the
reader rather than to the keypad.
Keypad Arming and Disarming
Area system Arming and Disarming
Press the lock icon and select the arming/disarming option. The keypad displays
ENTER CODE: -. Present your card to the reader. Once validated by the system, all
areas assigned to your code arm or disarm automatically and the 7873 keypad Door
Strike relay activates.
USER MENU
ENTER CODE: ARM
ALL
CHIME
1ABC
5MNO
9YZ
RESET
PERIM
DISARM
2DEF
6PQR
0
HOME
SLEEP
3GHI
7STU
4JKL
8VWX
CMD
ALL
CHIME
1ABC
5MNO
9YZ
RESET
PERIM
2DEF
6PQR
0
HOME
SLEEP
3GHI
7STU
4JKL
8VWX
CMD
Exit delay starts.
The System activates the Door Strike Relay and arms the area.
Figure 19: Area Arming and Disarming
All/Perimeter System Arming and Disarming
Present your card to the reader, the keypad displays PERIM ALL when arming. Select
the desired option. Once validated by the system, the selected areas arm or disarm
automatically. On 7873 keypads, the Door Strike relay then activates.
Home/Away System Arming and Disarming
Present your card to the reader. If the system is armed, once the card is validated, all
areas are disarmed and the keypad displays ALL SYSTEM OFF. If the system is disarmed
when you present your card, once the card is validated, HOME SLEEP AWAY displays.
Manually select HOME, SLEEP, AWAY or after a short time-out, all areas automatically
arm in the AWAY mode.
16
7800 Series Keypad Installation Guide
Keypad Door Strike
Area and All/Perimeter Door Strike
From the Status List, present your card to the reader. Once the system validates the
card, the Door Strike relay activates. Home/Away systems only activate the 7873
Door Strike relay when arming and disarming.
MON 5:35 AM
MON 5:35 AM
Panic
Panic
CURRENT
TODAY
HI
LO
WEDNESDAY 80 74
Chime
82
LO
98 77
HI
CURRENT
Chime
82
TODAY
Check-in
HI
LO
98 77
Check-in
Fire Reset
Fire Reset
HI
ARMED
LO
WEDNESDAY 80 74
ARMED
Typically, the relay activates for 5 seconds during which
time you can open the door. Once you open the door,
you have 40 seconds to exit and close the door before
the Zone 2 Soft-Shunt expires.
While the keypad displays the
Status List, present your access card.
Figure 20: Present Access Card
Keypad Entry Delay
All Systems
Once the entry delay starts, the keypad sounds an entry tone and displays ENTER
CODE: - . Present your card to the reader. Once validated, the system disarms all
areas accessible by you and activates the 7873 Door Strike relay. Area systems provide
a delay to allow selected areas only to be disarmed.
USER MENU
ENTER CODE: -
ENTER CODE: 1ABC
CHIME
5MNO
9YZ
ALL
2DEF
PERIM
6PQR
0
RESET
3GHI
SLEEP
7STU
HOME
4JKL
8VWX
CMD
1ABC
CHIME
5MNO
9YZ
ALL
RESET
PERIM
2DEF
6PQR
0
HOME
SLEEP
3GHI
7STU
4JKL
8VWX
CMD
Entry delay starts.
The System disarms the area and activates the Door Strike Relay.
Figure 21: Entry Delay
7800 Series Keypad Installation Guide
17
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications made by the user and not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Compliance Specifications
The keypad LED brightness setting must be set above the minimum setting.
Degraded Mode must be set to Relay Always Off.
Do not mount keypad on metal surfaces or metallic electrical boxes.
For listed access control applications, the keypad must be installed within the
protected area and all REX devices must be Listed to UL 294.
18
7800 Series Keypad Installation Guide
Wiring Specifications for Keypad Bus
When planning a keypad bus installation, keep in mind the following specifications:
1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and
LX-Bus circuits. Do Not use twisted pair or shielded wire for LX-Bus and keypad
bus data circuits. To maintain auxiliary power integrity when using 22-gauge
wire with a Model 7872 or 7873 do not exceed 225 feet. When using 18-gauge
wire do not exceed 500 feet. Install an additional power supply to increase the
wire length or add devices.
2. Maximum distance for any one circuit (length of wire) is 2,500 feet regardless
of the wire gauge. This distance can be in the form of one long wire run or
multiple branches with all wiring totaling no more than 2,500 feet. As wire
distance from the panel increases, DC voltage on the wire decreases.
3. Maximum number of devices per 2,500 feet circuit is 40.
Note: Each panel allows a specific number of supervised keypads. Add
additional keypads in the unsupervised mode. Refer to the panel installation
guide for the specific number of supervised keypads allowed.
4. Maximum voltage drop between the panel (or auxiliary power supply) and any
device is 2.0 VDC. If the voltage at any device is less than the required level,
add an auxiliary power supply at the end of the circuit. When voltage is too low,
the devices cannot operate properly.
Refer to the LX-Bus/Keypad Bus Wiring Application Note (LT-2031) for more
information. Also see the 710 Module Installation Sheet (LT-0310).
Keypad Specifications
MODEL
NORMAL/
STANDBY
CURRENT
ALARM
CURRENT
FOUR
ZONES
INTERNAL
PROX
READER
7872
130mA + 1.6mA 165mA + 2mA
per active zone per active zone
X
X
7873
130mA + 1.6mA 165mA + 2mA
per active zone per active zone
X
X
7800 Series Keypad Installation Guide
WIEGAND
INPUT
INTERNAL
DOOR
STRIKE
RELAY
X
X
19
Specifications
Operating Voltage
Dimensions
Compatibility
12 VDC
5.8” W x 4.135” H x 0.6” D
All keypads are compatible with all XR100/XR500 Series, XR150/XR350/XR550
Series, and XT30/XT50 Series panels.
Accessories
Keypad Wiring Harness
300-7800-12ADPT
12-Wire Harness adapter
300-7800-5
5-Wire Harness
300-7800-12
12-Wire Harness
Proximity Credentials
1306P
Prox Patch™
1306PW
Prox Patch™ 26-Bit
1326 HID
ProxCard II® Card
1386 HID
ISOProx II® Card
1346 HID
ProxKey II® Access Device
Proximity Readers for 7873 keypads
PP-6005B ProxPoint® Plus
30mA Standby
MP-5365 MiniProx™
20mA Standby
PR-5455 ProxPro II®
25mA Standby
TL-5395 Thinline™ II®
20mA Standby
Keypad Mounting
695-7800
In Wall Mount Backbox
698-7800
Plastic Keypad Wall Cover
699-7800
Keypad Deskstand with Cord
75mA Peak
110mA Peak
125mA Peak
115mA Peak
Certifications
California State Fire Marshall (CSFM)
FCC Part 15 RFID Reader FCC ID: CCKPC0131
Industry Canada ID: 5251A-PC0131
ANSI/UL 294
Access Control System Units
ANSI/UL 365
Police Connected Burglar
ANSI/UL 609
Local Burglar
ANSI/UL 1023
Household Burglar
ANSI/UL 1076
Proprietary Burglar
ANSI/UL 1610
Central Station Burglar
ANSI/UL 985
Household Fire Warning
LT-1162 1.03
16205
Download PDF
Similar pages