aparitwin strollercindermodel # 019112-384

APARI
TWIN STROLLER
CINDER
MODEL # 019112-384
IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
SAFETY PRECAUTIONS
Read all instructions before assembly and use of the twin stroller. Keep instructions
for future use.
WARNING
TO AVOID INJURY OR DEATH:
FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS STATIONARY.
USE THE TETHER STRAP AT ALL TIMES TO PREVENT THE STROLLER ROLLING AWAY.
DO NOT LEAVE CHILDREN UNATTENDED.
SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER.
MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE STROLLER,
OTHERWISE THEY MAY BE INJURED.
TO AVOID INJURY ENSURE THAT YOUR CHILD IS KEPT AWAY WHEN FOLDING AND
UNFOLDING THE STROLLER.
ENSURE THAT ALL LOCKING DEVICES ARE ENGAGED BEFORE USE.
Check that all safety locks are engaged before placing a child in the stroller.
Ensure your child is secured with a correctly adjusted safety harness.
DO NOT allow children to stand on the seat.
DO NOT hang bags or goods from the handle as this could cause the stroller to tip over.
DO NOT place more than 3kgs in each basket, or 1kg in each hood pocket.
The weight of the child should not exceed 17kgs (each seat).
The height of the child using the stroller should not exceed 96cm.
Only use accessories recommended by manufacturer. Using non-approved accessories may be unsafe.
NEVER ride with more than two child in the stroller.
It is recommended not to use stroller on escalators and stairs for safety reasons while child is in it.
This stroller is designed for use on flat or gently slopped surfaces and may become unstable (tipping over) on uneven surfaces
and slops of moderate to high elevation.
Always use safety locks.
Promptly replace worn out or broken parts.
Remove the child from the stroller before going up or down stairs and escalators.
DO NOT lift the stroller by the front bumper bar or tray (if supplied).
To prevent the risk of the stroller catching fire, do not park it near an open fire, heater or barbecue.
For warranty purposes, keep your sales receipt to provide proof of purchase.
DO NOT make any changes or alterations to this product, unless through an approved service agent.
To avoid the risk of suffocation, keep all plastic packaging materials out of reach of children.
NEVER leave safety harness connected when not fitted to a child in the stroller as this may create loops that could cause a
strangulation hazard.
When seat is in the fully reclined position, the canopy must be attached and fully secured at the back of the seat frame, as this
forms a safety head barrier at the top of the seat.
Ensure the storage latch is fully engaged when lifting or carrying the stroller.
CONGRATULATIONS
Congratulations on your purchase of the Apari Twin Stroller Cinder.
This product has been designed and developed with safety, comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Apari Twin Stroller
Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction
manual are generic, therefore product fabrics, colour and design may vary from images shown. CNP Brands reserves
the right to alter product specifications without notice as a result of our ongoing policy of product improvement.
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact Customer Service.
In Australia, contact CNP Brands on 1300 667 137, in New
Zealand contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Bumper bar
x2
Front Dual Swivel
Wheels
x2
Rear Wheels
x2
Stroller Frame
(Pre-Assembled)
•Five Point Safety Harness
•Storage Basket
•Shoulder Pads
•Hood
There are no recommended accessories to be used with Bebe Care Apari Twin Stroller.
x2
x2
x4
x2
ASSEMBLY / OPERATING INSTRUCTIONS
To unfold Stroller...
1
2
1a.
Release the folding lock as shown in image.
2a.
Lift handle and seat apart until the frame ‘clicks’
and locks on both sides.
Ensure stroller is locked on both sides before
continuing.
2b.
WARNING
ENSURE CHILDREN STAY CLEAR WHEN UNFOLDING/FOLDING THE STROLLER.
To attach Front Swivel Wheels...
1
2
1a.
Insert the metal shaft of the wheel into the front wheel
housing on the stroller frame until it ‘clicks’ into
position.
2a.
Pull the wheel downwards to make sure it is securely
attached before using stroller.
Repeat for other Front Swivel Wheel.
2b.
ASSEMBLY / OPERATING INSTRUCTIONS
To remove Front Swivel Wheels...
1
2
1a.
Press button on the top of the wheel housing.
2a.
2b.
Pull the wheel downwards to release from housing.
Repeat for other Front Swivel Wheel.
To operate Swivel Function...
1
1a.
1b.
2
2a.
2b.
To lock swivel wheels, slide lever downwards until it
’clicks’.
Repeat for other Front Swivel Wheel.
To unlock swivel wheels, rotate lever upwards until it
‘clicks’.
Repeat for other Front Swivel Wheel.
CAUTION! Always unlock the swivel function before folding the stroller.
ASSEMBLY / OPERATING INSTRUCTIONS
To attach Rear Wheels...
1
1a.
1b.
Lift the rear of the stroller slightly upwards.
Insert the rear wheel axle into the housing until it
clicks into place.
2
2a.
2b.
Pull wheel outwards to check it is secure.
Repeat for other Rear Wheel.
To use Rear Brake...
1
2
1a.
To lock rear wheels, push down on the rear red
brake pedal on the rear wheel housing with
foot.
2a.
To unlock rear wheels, lift the rear red brake
pedal with foot.
CAUTION! Always apply rear brake when parking stroller.
ASSEMBLY / OPERATING INSTRUCTIONS
To adjust Backrest (5 positions)...
1
1a.
1b.
2
2a.
2b.
To lower backrest, pull metal adjuster outwards
and lower backrest to desired position.
Release adjuster and check that the backrest is
secure.
To raise backrest, pull the adjuster outwards
and raise backrest to desired position.
Release adjuster and check that the backrest is
secure.
To adjust Canopy...
1
2
1a.
To open, pull canopy forward until extended.
2a.
To close, push canopy back.
CAUTION! The canopy must be fully closed before folding the
stroller.
ASSEMBLY / OPERATING INSTRUCTIONS
To adjust Viewing Window...
1
2
1a.
To open, lift viewing window flap forward.
2a.
To close, lower back into place and flap will secure
with magnets.
To adjust Sun Visor...
1
2
1a.
To open, lift out from front of hood.
2a.
To close, push back.
ASSEMBLY / OPERATING INSTRUCTIONS
Restraints - Harness...
1
To secure the child in the harness, place
left hand buckle prong (b) on top of (a).
f
a
f
2
Hold both left hand buckle prongs (a)
and (b) together and insert it into buckle
housing (e) until it snaps into position.
f
c
b
f
d
e
f
3
4
5
Repeat previous steps for right hand
buckle prongs (c) and (d).
Once all attached, carefully adjust the
harness straps by pulling each slider (f)
until the desired fit is achieved in the lap,
shoulder and crotch straps.
To release the buckles, squeeze the top
and bottom prongs (a) and (b), (c) and
(d) together until harness disengages.
CAUTION: Always adjust the harness
when changing the seating position of
the child.
(a), (b): Left hand buckle prongs
(c), (d): Right hand buckle prongs
(e): Buckle housing
(f): Strap adjustment sliders
WARNING
USE THIS HARNESS AT ALL TIMES
ASSEMBLY / OPERATING INSTRUCTIONS
To adjust Waist Strap...
1
1a.
To loosen waist strap, push up both top and bottom
straps through buckle as circled in diagram.
To place waist strap in desired position, slide the
bottom strap into position then pull the top strap and
tighten into position.
To use Tether Strap...
1
1a.
Ensure tether strap is used at all times.
Make sure your hand is fed through the loop as
shown to the right.
To attach Bumper Bar...
1
2
1a.
To attach the bumper bar, gently insert the
bumper into the slots until they click into
position.
2a.
To remove, push release button on inside of
mountings and pull bar outwards.
Top strap
Bottom
strap
ASSEMBLY / OPERATING INSTRUCTIONS
To adjust Footrest (3 positions)...
1
2
1a.
To adjust the footrest, press both buttons located at
the pivot point of the footrest as shown.
2a.
Once both buttons are depressed manually adjust
the footrest to the desired position.
To fold Stroller...
1
2
1a.
Ensure the both canopies are closed and the both
seats are fully reclined before folding.
2a.
Push button on plastic barrel of handle while
twisting barrel forward.
ASSEMBLY / OPERATING INSTRUCTIONS
To fold Stroller continued...
3
4
3a.
Continue pushing downwards until the stroller is
folded.
4a.
Ensure folding lock is engaged.
HOW TO CARE FOR YOUR BEBE CARE STROLLER
Cleaning
To ensure the long-lasting use of your stroller, dry it with a soft absorbent cloth
after use in rainy weather. Use a damp cloth to clean the frame. Do not use
abrasive cleaners. After using your stroller on the beach, clean the frame
and wheels thoroughly with water to remove the sand and salt. Allow it to
dry thoroughly. Removable and non-removable fabric covers and trims may
be cleaned using a damp cloth with soap or mild detergent. Allow it to dry
completely before folding or storing away. Do not dry clean or use bleach
on fabrics or trims. Do not machine wash, tumble or spin dry, unless the care
labelling on the product permits these methods.
Maintenance
Check stroller regularly to ensure that locking devices and components are
secure and working properly. Always check parts regularly for tightness of
screws, nuts and other fasteners – tighten or replace if required. To maintain
the safety of your stroller, seek prompt repairs for bent, torn, worn or broken
parts. Use only those parts and accessories approved by CNP Brands. If the
wheels squeak, use silicone based spray or light oil ensuring it penetrates the
wheel and axle assembly. To prevent mould or mildew, do not fold or store
the product if it is damp or wet. Allow it to dry thoroughly. Always store the
product in a well ventilated area and away from direct sunlight.
If you have any difficulties in assembling the stroller, please contact our
Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact
Wainhouse Distribution on 0800 567 5000.
ABOUT US
About CNP Brands
Currently, CNP Brands boasts one of the most diverse brand portfolios with
a combination of company owned brands and distribution agreements.
These include distribution lines for 4moms, Brica, Cybex, Evenflo, Good
Baby, Lascal, Maclaren, Motorola, Munchkin, OiOi and Summer Infant.
Our own brands, including Childcare, have gone from strength to
strength in recent years. Childcare, and our premium brand bebe care,
demonstrate our commitment to quality and continuing investment in
product development.
Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut, VIC, 3030
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: info@cnpbrands.com.au
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000
E: helpline@wainhousedist.co.nz
Download PDF
Similar pages