Installation and Operating Guide | Warranty
Model Number | ZHX-313 | DVD+Hi-Fi VCR System
(Speakers: LHS-C245T/LHS-C245W)
© Copyright 2004, Zenith Electronics Corporation
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: Do not install this equipment in a confined space
such as a bookcase or similar unit.
NOTE TO CABLE/TV INSTALLER: This reminder is provided to
call the cable TV system installer’s attention to Article 820-40 of
the National Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of the cable entry as practical.
CAUTION:
This DVD+Hi-Fi VCR System employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference. Should the
unit require maintenance, contact an authorized service center
see back page for instructions.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
OTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product uses copyright protection developed by
Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. _________________________________
Serial No. _________________________________
Use of controls, adjustments, or the performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open.
DO NOT STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
2
CD-R/RW
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and
other areas located near water.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Disc Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel Control Buttons . . . . . . . . . . . . . . . . . . 7
Display Window Indicators . . . . . . . . . . . . . . . . . . . 8
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . 10
System Setup
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Connecting Antenna/Cable TV to DVD+Hi-Fi
VCR System . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12
Optional TV Connections . . . . . . . . . . . . . . . . . . 12
Accessory Audio/Video (A/V) Connections to
DVD+Hi-Fi VCR . . . . . . . . . . . . . . . . . . . . . . . . . 13
Radio Antenna Connections . . . . . . . . . . . . . . . . 13
Speaker System Connections . . . . . . . . . . . . . . 14
Speaker Positioning . . . . . . . . . . . . . . . . . . . . . . 14
Glossary for Audio Stream & Surround mode . . . 15
VCR Operation Setup . . . . . . . . . . . . . . . . . . . . 16-18
On-Screen Display (OSD) . . . . . . . . . . . . . . . . . 16
On-Screen Menus Setup . . . . . . . . . . . . . . . . . . 16
VCR Setup Menu Options . . . . . . . . . . . . . . . . . 17
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 18
DVD Operation Setup . . . . . . . . . . . . . . . . . . . . 19-23
General Explanation. . . . . . . . . . . . . . . . . . . . . . 19
On-Screen Display . . . . . . . . . . . . . . . . . . . . 19-20
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 21-23
General Operation . . . . . . . . . . . . . . . . . . . . 21
Language . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.1 Speaker setup . . . . . . . . . . . . . . . . . . . . 22
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Parental Control . . . . . . . . . . . . . . . . . . . . . . 23
Operation
VCR Operation . . . . . . . . . . . . . . . . . . . . . . . . . 24-29
Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 24
Special Effect Playbacks . . . . . . . . . . . . . . . . . . 24
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Still Picture and Frame-by-Frame Playback . 24
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 24
CM Skip (Commercial Skip) . . . . . . . . . . . . . 24
Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 25
Timer Recording . . . . . . . . . . . . . . . . . . . . . . 25-26
Instant Timer Recording . . . . . . . . . . . . . . . . . . . 27
Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 27
Copying from DVD to VCR. . . . . . . . . . . . . . . . . 27
VHS Hi-Fi Stereo System/MTS Broadcast . . . . . 28
Tape Counter Memory Feature. . . . . . . . . . . . . . 29
Additional Information . . . . . . . . . . . . . . . . . . . . 29
DVD Operation . . . . . . . . . . . . . . . . . . . . . . . . . 30-33
Playing a DVD . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General Features . . . . . . . . . . . . . . . . . . . . . . . . 30
Moving to another TITLE/GROUP . . . . . . . . 30
Moving to another CHAPTER/TRACK . . . . . 30
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4
Still Picture and Frame-by-Frame Playback . 31
Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 31
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 31
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 31
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 32
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Marker Search . . . . . . . . . . . . . . . . . . . . . . . 32
Special DVD Features . . . . . . . . . . . . . . . . . . . . 32
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 32
Changing the Audio Language . . . . . . . . . . . 32
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DVD Audio Discs . . . . . . . . . . . . . . . . . . . . . . . . 33
Moving to another GROUP . . . . . . . . . . . . . . 33
Viewing another PAGE. . . . . . . . . . . . . . . . . 33
Audio CD and MP3/WMA Disc Operation . . . . 34-35
Playing an Audio CD and MP3/WMA Disc . . . . . 34
Notes on MP3/WMA Recordings . . . . . . . . . . . . 34
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Moving to another Track . . . . . . . . . . . . . . . 35
Repeat Track/All/Off. . . . . . . . . . . . . . . . . . . 35
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 35
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 35
Changing the Audio Channel . . . . . . . . . . . . 35
JPEG Disc Operation . . . . . . . . . . . . . . . . . . . . . . 36
Viewing a JPEG disc . . . . . . . . . . . . . . . . . . . . . 36
Moving to another File . . . . . . . . . . . . . . . . . 36
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . 36
To flip the picture . . . . . . . . . . . . . . . . . . . . . 36
To rotate picture. . . . . . . . . . . . . . . . . . . . . . 36
Notes on JPEG Recordings . . . . . . . . . . . . . 36
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 37
Programmed Playback with Audio CD
and MP3/WMA Disc . . . . . . . . . . . . . . . . . . . . . . 37
Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 39-40
Presetting Radio Stations . . . . . . . . . . . . . . . . . . 39
Radio Operation. . . . . . . . . . . . . . . . . . . . . . . . . 39
To Clear Stored Radio Stations . . . . . . . . . . . . . 39
Tuning Stations Manually . . . . . . . . . . . . . . . . . . 40
Tuning Stations Automatically. . . . . . . . . . . . . . . 40
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Labeling Stations . . . . . . . . . . . . . . . . . . . . . . . . 40
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 41-42
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 43
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 45-46
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished works. Copyright 19921997 Dolby Laboratories. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 5,956,674, 5,974,380, 5,978,762 and
other worldwide patents issued and pending. “DTS” and “DTS
Digital Surround” are registered trademarks of Digital Theater
Systems, Inc. Copyright 1996, 2000 Digital Theater Systems,
Inc. All rights reserved.
Before Use
Playable Discs
Title (DVD video discs only)
The main film content or accompanying feature content
or additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
DVD audio discs
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play a DVD-RW, DVD+RW,
SVCD and CD-R or CD-RW that contains audio titles,
MP3, WMA or JPEG files.
otes
Depending on the conditions of the recording equipment or the CD-R/RW (or DVD-RW, DVD+RW) disc
itself, some CD-R/RW (or DVD-RW, DVD+RW) discs
cannot be played on the unit.
Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Regional code of the DVD/CD receiver and DVDs
This DVD/CD receiver is designed and manufactured for
playback of region “1” encoded DVD software. The
region code on the labels of some DVDs indicates which
type of player can play those discs. This unit can only
play DVDs labeled “1” or “ALL”. If you try to play any
other discs, the message “Check Regional
Code” will appear on the TV screen. Some
DVDs that have no region code label may still be
subject to area restrictions and therefore not
playable.
1
Group (DVD audio discs only)
The main audio content or accompanying feature
content or additional feature content, or music album.
Each group is assigned a group reference number
enabling you to locate it easily.
Track (DVD audio discs and audio CD only)
Sections of a picture or a musical piece on an audio
CD. Each track is assigned a track number, enabling
you to locate the track you want.
Remote Control Battery Installation
AAA
otes on DVDs
Some playback operations of DVDs may be intentionally fixed by software manufacturers. As this unit plays
DVDs according to disc content designed by the software manufacturer, some playback features of the unit
may not be available or other functions may be added.
Make sure to also refer to the instructions supplied with
the DVDs. Some DVDs made for business purposes
may not be able to be played on the unit.
Chapter (DVD video discs only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number,
enabling you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
AAA
DVD video discs
(8 cm / 12 cm disc)
Detach the battery cover on the rear of the
remote control, and insert two R03 (size
AAA) batteries with
and
aligned
correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Remote Control Operating Range
Point the remote control at the remote sensor and press
the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor
Angle: About 30° in each direction of the front of the
remote sensor
5
INTRODUCTION
Disc-related terms
Before Use (Continued)
Precautions
Handling the unit
Shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
Setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
Keeping unit surfaces clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
Cleaning the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD+Hi-Fi VCR is a high-tech, precision device. If
the optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Disc handling
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center outward.
Yes
No
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Disc Symbols
About the
symbol display
may appear on the TV screen during operation. This
icon means the function explained in this owner’s manual is not available on that specific DVD video disc.
About the disc symbols on manual pages
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
DVD-V
DVD Video discs.
DVD-A
DVD Audio discs.
CD
Audio CDs.
MP3
MP3 disc.
WMA
WMA disc.
JPEG
JPEG disc.
Selecting Viewing Sources
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
• If you want to view DVD deck output source:
Press CD/DVD on the remote or DVD/VCR on the front
panel until READING indicator in the display window lights
and output source of DVD deck is viewed on the TV screen.
• If you want to view VCR deck output source:
Press VCR on the remote or DVD/VCR on the front panel
until VCR indicator in the display window lights and output
source of VCR deck is viewed on the TV screen.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
6
otes
• If you insert a disc while the DVD+Hi-Fi VCR System
is in the VCR mode, the DVD+Hi-Fi VCR System will
switch to DVD mode automatically.
• If you insert a cassette tape without prevention tab
while the DVD+Hi-Fi VCR System is in the DVD
mode, the DVD+Hi-Fi VCR System will switch to VCR
mode automatically.
Front Panel Control Buttons
Z)
EJECT(Z
Ejects a tape from the VCR deck.
Z)
OPEN/CLOSE (Z
Opens and closes the disc tray.
Disc Tray (DVD deck)
Insert a disc here.
X/C
C)
PAUSE/STEP(X
Pause playback of a disc or a tape in the DVD or
VCR deck /press repeatedly for
frame-by-frame playback.
INTRODUCTION
Remote Sensor
Point the remote control here.
x)
STOP (x
Stops playback of a disc or
tape.
INPUT SELECT
Selects the VIDEO
deck’s source (Tuner,
VIDEO 1 or VIDEO 2)
PLAY (B)
Plays back a recorded disc or tape.
Cassette Compartment
(VCR deck)
Insert a video cassette here.
Display window
DVD/VCR (output select)
Selects the DVD or VCR output sources to
view on the TV screen.
CH/PRESET (v/V)
Tunes in the desired station (Radio Mode).
Scans up or down through memorized
channels (VCR mode).
TUNER FM/AM
Switches between AM and FM bands.
z)
REC/ITR (z
Records normally or activates Instant Timer Recording.
Press to copy a DVD in the DVD deck to a VHS tape in
the VCR deck.
AUDIO L/R (Left/Right))
Connect the audio/video output of an external source
(Audio system, TV/Monitor, another VCR).
S/Q
Q)
Reverse SKIP/SCAN (S
DVD: Goes to the beginning of current chapter/track or to the previous
chapter/track. Press and hold for two seconds for a fast reverse search.
VCR: Rewinds the tape from the STOP mode or for fast reverse picture search.
R/T
T)
Forward SKIP/SCAN (R
DVD: Goes to NEXT chapter/track. Press and hold for two seconds for a
fast forward search.
VCR: Advances the tape from the STOP mode or for fast
forward picture search.
STANDBY/ON
Switches the DVD+Hi-Fi VCR ON and OFF.
VOLUME Control
Turn the knob clockwise to increase sound level,
counterclockwise to decrease sound level.
7
Display Window Indicators
A disc is loaded in the DVD deck. (Lights when a disc is
loaded in the DVD deck and flashes when the disc tray
is opened.)
Indicates current
audio stream.
DVD+Hi-Fi VCR is in VCR timer recording mode
or a VCR timer recording is programmed.
Indicates the unit is in the radio
mode.
DVD to VCR copy is in progress.
DVD+Hi-Fi VCR is Recording a tape.
Indicates the current
surround mode.
Indicates the unit is
playing back a tape
recorded in Hi-Fi.
Lights up when an SAP
BILINGUAL broadcast
is being received.
MUTE indicator
A cassette
is loaded
in the VCR
deck.
Programmed
playback active.
DIGITAL
PCM
PHOTO
P/SCAN
dts
PROLOGIC
RADIO DVD
II PROG
TITLE
CHPTRK
COPY
Hi-Fi
MUTE
MP3 TV
ST
RPT ALL A B
Indicates current chapter,
track number or channel
number.
Indicates the unit is in the TV mode.
MP3 or WMA disc inserted.
Repeat playback
mode indicators.
DVD disc inserted.
Lights up when a stereo broadcast
is being received.
Indicates the unit is in progressive
scan mode.
JPEG file disc inserted
8
REC
SAP
Total playing time/Elapsed time/
Frequency/remaining time/ Current
deck status/Surround mode/Volume
etc. indicators.
Remote Control Buttons
POWER
Z)
EJECT, OPEN/CLOSE(Z
Switches DVD+Hi-Fi VCR ON and OFF.
CD/DVD/VCR select
Selects the output source (CD/DVD or
VCR) to view on the TV screen.
FM/AM Tuner select
Select FM or AM band as the listening
choice. (FM and AM bands)
0-9 Number Keypad
Selects numbered options in a menu.
AUX
PROGRAM
Accesses or removes Program menu.
CLEAR
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
Clears preset stations from the tuner
memory.
DISPLAY, CLK/CNT
Accesses On-Screen display.
Switches between the clock, tape counter
and tape remaining modes on the display.
b/B/v/V (left/right/up/down)
Select menu options.
CH/TRK/PRESET(v/V):
Selects VCR or Tuner channels Manually
adjust the VHS’s picture tracking.
RETURN
Removes the Setup menu.
z)
REC/ITR (z
Records normally or activates Instant
Timer Recording.
.)
BACKWARD (.
DVD: Search backward*/go to beginning of current chapter or track or go to
previous chapter or track.
VCR: Rewinds the tape from STOP
mode or for fast reverse picture search.
*Press and hold button for about two
seconds.
>)
FORWARD (>
DVD: Search forward*/go to next
chapter or track.
VCR: Advances the tape from STOP
mode or for fast forward picture search.
*Press and hold button for about two
seconds.
ANGLE
Selects a DVD camera angles if
available.
CM SKIP
Fast forwards picture search through 30
seconds of recording.
TITLE
Displays the disc’s Title menu, if
available.
ote
This remote control use the same buttons for VCR and DVD functions (ex. PLAY).
To use the VCR, first press the VCR button.
To use the DVD, first press the CD/DVD button.
Not Included on this Remote
S
INPUT
Selects the VCR deck’s source
(Tuner, LINE 1, or LINE 2).
SOUND MODE
Selects sound mode.
AUDIO
Selects an audio language (DVD) or an
audio channel (CD).
SET UP, MENU
Accesses or removes DVD Setup menu
and VCR menu.
MEMORY/ENTER
- Acknowledges menu selection.
- Displays functions on the TV screen.
- Stores a radio station’s frequency in
the tuner’s memory.
DISC MENU
Accesses menu on a DVD disc.
VOLUME (+/-)
Adjusts speaker sound.
x)
STOP (x
Stops playback.
X)
PAUSE/STEP (X
Pause playback or recording
temporarily/press repeatedly for
frame-by-frame playback.
PLAY (B)
Starts playback.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
TUNING(v/V)
Tunes in the desired station.
SUBTITLE
Selects a subtitle language.
MUTE
Turns the sound on and off temporarily.
REPEAT/A-B/SPEED
Repeat chapter, track, title, all.
Repeats sequence.
Selects recording speed.
TV/VCR
Switch to view channels selected by the
VCR tuner or by the TV tuner.
ZOOM
Enlarges DVD video image.
9
INTRODUCTION
Opens and closes the disc tray.
Ejects a tape in the VCR deck.
Rear Panel Connections
FM ANTENNA CONNECTORS
Connect the FM antenna to this terminal.
SPEAKER CONNECTORS
Connect the six supplied speakers to
these terminals.
ANTENNA IN
Connect the VHF/UHF/CATV antenna
to this terminal.
COMPONENT/PROGRESSIVE SCAN
VIDEO OUT (Y Pb Pr)
(DVD OUT)
Connect to a TV with Y Pb Pr inputs.
AC Power Cord
Plug into the power source.
VCR IN LINE 1
(VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output
of an external
source (Audio system, TV/Monitor,
another VCR).
DVD/VCR OUT VIDEO OUT/AUDIO OUT
(Left/Right))
Connect to a TV with video and
audio inputs.
ANTENNA/CABLE OUT
Connect to a TV with RF coaxial inputs.
S-VIDEO OUT (DVD OUT)
Connect to an S-Video Input on TV.
FOR DVD VIEWING ONLY.
AM ANTENNA CONNECTORS
Connect the AM antenna to
this terminal.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
10
Connections
Depending on your TV and other equipment you wish to
connect, there are various ways to connect the DVD+Hi-Fi
VCR. Use connections described on pages 11-13.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the best
connections.
Caution
Make sure the DVD+Hi-Fi VCR is connected directly to the
TV. Tune the TV to the correct video input channel.
Do not connect your DVD+Hi-Fi VCR via your VCR. The
DVD image could be distorted by the copy protection system.
Connecting Antenna/Cable TV to
DVD+Hi-Fi VCR
the antenna leads from the rear of the
1 Disconnect
TV.
the type of cable from your antenna. If it is
2 Identify
a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
the jack marked ANTENNA/CABLE IN on your
DVD+Hi-Fi VCR.
ip
If your antenna lead wire is a flat type antenna cable,
connect it to an Antenna Adapter (300-ohm to 75-ohm)
(not supplied) and slip the Adapter onto the ANTENNA/
CABLE IN jack. The Adapter does not screw on to the
DVD+Hi-Fi VCR, it just slips over the jack.
Antenna
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANTENNA/CABLE IN jack on the DVD+Hi-Fi VCR.
Use the supplied round coaxial cable to connect between the
DVD+Hi-Fi VCR’s ANTENNA/CABLE OUT jack and the 75
ohm antenna input jack on the TV. With this connection, you
can receive all midband, super band, and hyperband channels.
With Cable Box
If a converter is required in your cable system, follow the
instruction below:
The cable hookup permits both TV and DVD+Hi-Fi VCR
operation.
To view or record CATV channel
1 Tune the TV to the DVD+Hi-Fi VCR output channel (CH 3 or
4).
2 Set the DVD+Hi-Fi VCR channel selector to the output
channel of the Cable Converter box by using the CH/TRK
(v/V) of your DVD+Hi-Fi VCR. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
otes
With this connection, you CANNOT record one program
while viewing another.
If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming as indicated on
page 17.
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
300/75 ohm
Adapter
(Not supplied)
OR
OR
Rear of DVD+Hi-Fi VCR
Rear of DVD+Hi-Fi VCR
ote
During DVD or VCR playback, The DVD+Hi-Fi VCR is
designed so that sound will be heard only from the unit’s 5
speakers and subwoofer, (no sound output is provided to the
TV if it is connected to the S-VIDEO OUT or MONITOR OUT
on the unit with a optional cables.
11
SYSTEM SETUP
Without Cable Box
ips
Connections (Continued)
Basic TV Connections
Optional TV Connections
Make one of the following connections, depending on
the capabilities of your existing equipment.
RF coaxial connection
Connect the ANTENNA/CABLE OUT jack on the
DVD+Hi-Fi VCR to the ANTENNA in jack on the TV
using the 75-ohm Coaxial Cable supplied (R).
ote
If you use this connection, tune the TV to the DVD+HiFi VCR’s RF output channel (CH 3 or 4).
How to set the DVD+Hi-Fi VCR’s RF output channel
1. While the DVD+Hi-Fi VCR is turned off, press and hold
TUNING (v/V) on the front panel for about five
seconds.
The unit will turn itself on and “RF-03” or “RF-04” appears in
the display window.
2. Use TUNING (v/V) on the front panel to change the
RF output channel (CH 03 or CH 04).
3. Turn the DVD+Hi-Fi VCR off and then on.
4. Select the TV’s CH to 3 or 4 depending on the RF
output channel you had selected.
Now you can watch the DVD+Hi-Fi VCR playback on
CH3 or CH4 of your TV.
Audio/Video connection
1
ote
DVD playback can also be done using the S-VIDEO OUT
and COMPONENT/PROGRESSIVE SCAN VIDEO OUT
connection options below. The tuner and VCR ONLY
output through the RF.OUT (R) or DVD/VCR OUT (A,
V) jack. (See left)
S-Video Connection
1
the Left and Right AUDIO OUT jacks on
2 Connect
the DVD/VCR Receiver to the audio left/right in
jacks on the TV using the supplied audio cables
(A).
Component Video (Color Stream®) connection
1
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD/VCR Receiver to the audio left/right in
jacks on the TV (A) using the supplied audio
Progressive Scan (ColorStream® pro) connection
If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD/VCR
Receiver’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the DVD/VCR Receiver.
the Left and Right DVD/VCR AUDIO OUT
2 Connect
jacks on the DVD/VCR Receiver to the audio
left/right in jacks on the TV (A) using the supplied
audio cables.
otes
If you use this connection, set the TV’s source selector to
VIDEO.
Rear of TV
VIDEO
INPUT
L
A
R
L
V
COMPONENT/PROGRESSIVE
SCAN VIDEO INPUT
Pr
Pb
C
Connect the COMPONENT/PROGRESSIVE SCAN
VIDEO OUT jacks on the DVD/VCR Receiver to the
corresponding in jacks on the TV using Y Pb Pr
cables (C).
cables.
Connect the DVD/VCR VIDEO OUT jack on the
DVD/VCR Receiver to the video in jack on the TV
using the supplied video cable (V).
AUDIO INPUT
Connect the S-VIDEO OUT jack on the DVD/VCR
Receiver to the S-Video in jack on the TV using the
S-Video cable (S).
ANTENNA
INPUT
S-VIDEO
INPUT
1
Connect the COMPONENT/PROGRESSIVE SCAN
VIDEO OUT jacks on the DVD/VCR Receiver to the
corresponding in jacks on the TV using Y Pb Pr
cable (C).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD/VCR Receiver to the audio left/right in
jacks on the TV (A) using the supplied audio
Y
R
cables.
S
otes
Set the Progressive Scan to “On” on the DVD setup
menu for progressive signal, see page 21.
Progressive scan does not work with the analog video
connections (yellow VIDEO OUT and S-VIDEO OUT
jack).
Rear of DVD Hi-Fi VCR
12
Connections (Continued)
Connect the VIDEO 1 or VIDEO 2 jacks on the
DVD+Hi-Fi VCR to the AUDIO/VIDEO OUT jacks on
your
accessory component, using the optional audio/video
cables.
SYSTEM SETUP
Accessory Audio/Video (A/V)
Connections to DVD+Hi-Fi VCR
Accessory Device Jack Panel
AUDIO
OUTPUT
R
L
VIDEO
OUTPUT
OR
Rear of DVD Hi-Fi VCR
Radio Antenna Connections
Front of DVD
Hi-Fi VCR
AM Loop antenna (supplied)
Connect the supplied FM/AM antennas for listening to
the radio.
Connect the AM loop antenna to the AM antenna
connector.
Connect he FM wire antenna to the FM antenna connector.
otes
FM Wire antenna (supplied)
To prevent noise pickup, keep the AM loop antenna away
from the DVD+Hi-Fi VCR and other components.
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as close to
horizontal as possible.
13
Connections (Continued)
Speaker System Connections
Connect the speakers using the supplied speaker cables.
To obtain the best possible surround sound, adjust the speaker parameters; distance, level, etc..
Front speaker
(Left)
Front speaker
(Right)
Rear speaker
(Right surround)
Rear speaker
(Left surround)
Subwoofer
otes
Be sure to match the speaker cable to the appropriate terminal on the connectors: + to + and – to –. If the cables are reversed,
the sound will be distorted and will lack bass.
When making the sound louder, adjust the sound level carefully to avoid excessive volume output to the speakers.
Only 2-channel stereo (Front Left, Front Right & Subwoofer) is abailable in VCR mode, thus sound might not be heard from
center or rear speakers during VCR playback. (For further details about sound mode, please refer to next page.)
Do not remove the front covers of supplied speakers.
Speaker Positioning
For a normal setup, use 6 speakers (2 front speakers,
1 center speaker, 2 rear speakers and a subwoofer).
If you want to hear excellent bass sound or Dolby Digital
surround, you should connect a subwoofer.
Subwoofer
• Front speakers
Center Speaker
From your listening position, place the speakers an equal distance away and with an interval of 45 degrees between speakers.
Front Speaker
Front Speaker
(Right)
• Center speaker
(Left)
It is ideal if the center speakers and front speakers are at the
same height. You would normally place the center speaker
Rear
above or below television as shown.
Rear
Speaker
• Rear speakers
Speaker
(Right)
Place left and right behind the listening area. These speakers
(Left)
recreate sound motion and atmosphere required for surround
sound playback. For best results, do not install the rear speakers too far behind the listening position and install them at or
above the level of the listener’s ears. It is also effective to direct
the rear speakers towards a wall or ceiling to further disperse
the sound.
For smaller room size, if the audience is near to the rear wall.
place the rear speakers opposite each other, and 24 - 36 inches
above the listeners’ ears.
Speaker Positioning Example
• Subwoofer
This can be placed in any front position.
14
Glossary for Audio Stream & Surround mode
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
program you want to listen to.
Each time you press the SOUND MODE button, the
sound mode is changed in the following order;
PRO LOGIC → PLII MOVIE → PLII MUSIC → PLII MATRIX →
3D SURROUND → BYPASS ...
The Dolby Digital surround format lets you enjoy up to 5.1
channels of digital surround sound from a Dolby Digital program source. If you play DVDs with “
” mark, you can enjoy
even better sound quality, greater spatial accuracy, and
improved dynamic range.
Use this mode when playing movie or Dolby Digital 2 channel
which carries the “
” mark. This mode provides the effect
of being in a movie theatre or live concert house-an effect with
an intensity which can only be obtained through DOLBY PRO
LOGIC SURROUND. The effect of the front/back/left/right
movement of the sound image, as well as the sense of fixed
position in the sound image, is much clearer and more dynamic than before.
(II)
Dolby Pro Logic II creates five full-bandwidth output channels
from two-channel sources. This is done using an advanced,
high-purity matrix surround decoder that extracts the spatial
properties of the original recording without adding any new
sounds or tonal colorations.
MOVIE mode:
The Movie mode is for use with stereo television shows and all
programs encoded in Dolby Surround. The result is enhanced
soundfield directionality that approaches the quality of discrete
5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music recordings.
MATRIX mode:
The Matrix mode is the same as the Music mode except that the
directional enhancement logic is turned off. It may be used to
enhance mono signals by making them seem “larger.” The Matrix
mode may also find use in auto systems, where the fluctuations
from poor FM stereo reception can otherwise cause disturbing
surround signals from a logic decoder. The ultimate “cure” for
poor FM stereo reception may be simply to force the audio to
mono.
For DVD Operation
You can change the sound mode of DVD (Dolby Digital, DTS,
PRO LOGIC, etc.) by pressing the AUDIO button repeatedly on
the remote during playback.
Although DVD contents differ from disc to disc, the following
explains the basic operation when this feature is used.
Each time you press AUDIO, the DVD+Hi-Fi VCR sound mode
is changed in the following order;
→
→
→
For your reference
• The DVD/CD Receiver memorizes the last mode
setting for each source individually.
• You can identify the encoding format of program
software by looking at its packaging.
- Dolby Digital discs are labeled with the
logo.
- Dolby Surround encoded programs are labeled with
the
logo.
- DTS Digital Surround discs are marked with DTS.
ote
When you play sound tracks with 96kHz sampling frequency, the output signals will be converted to 48kHz (sampling
frequency).
3D SURROUND
This unit can produce a 3D Surround effect, using 3D Surround
Sound technology, which simulates multi-channel audio playback from two conventional stereo speakers instead of the five
or more speakers normally required to listen to multi-channel
audio from a home theatre. This feature works with DVD discs
encoded with Dolby Pro Logic and Dolby Digital audio tracks.
BYPASS
Software with multichannel surround audio signals is played according to the way it was recorded.
15
SYSTEM SETUP
Sound Mode
Allows you to enjoy 5.1(or 6) discrete channels of high quality
digital audio from DTS program sources such as discs, DVD
and compact discs, etc. bearing the trademark. DTS Digital
Surround delivers up to 6 channels of transparent audio and
results in exceptional clarity throughout a true 360 degree
sound field. The term DTS is a trademark of DTS Technology,
LLC. Manufactured under license from DTS Technology, LLC.
VCR Operation Setup
On-Screen Display (OSD)
Some of these functions appear during VCR operation.
❶
❷
❸
PLAY
SP
HI-FI
❹
❺
CH 4
STEREO
JUL 5 , SAT
2:15 PM
❻
❼
❶ TAPE SPEED DISPLAY
Shows the current tape speed.
❷ FUNCTION DISPLAY
Indicates the function in progress.
❸ HI-FI DISPLAY
Indicates the unit is playing back tape recorded in Hi-Fi.
❹ CHANNEL DISPLAY
Indicates the selected channel (or LINE1, LINE2).
❺ STEREO/SAP DISPLAY (MONO is not displayed)
Shows the type of audio signal received by the VCR tuner.
EASY INFORMATION
If the Extended Data Service (XDS) signals are provided
along with normal TV signal in your area or during playback of a tape recorded with Extended Data Service
(XDS) signals, the station ID, program title, and program
details are shown on the TV screen.
When viewing a channel with Extended Data Service (XDS)
signals, press MEMORY/ENTER and the station ID will
appear on the TV screen. Press MEMORY/ENTER again
and the program details will appear on the TV screen.
When viewing a tape recorded with Extended Data
Service (XDS) signals, press MEMORY/ENTER twice
and the program title and program details will appear on
the TV screen.
PROGRAM DETAILS
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
SP
CH 4
WABC STEREO
❻ DATE DISPLAY
Shows the current date. (Month/Date/Day of the week
format)
❼ CLOCK/COUNT/REMAIN DISPLAY
Shows the current time, the tape counter and remaining time
on the tape.
Each press of MEMORY/ENTER changes the TV
on-screen displays in the following sequence.
STOP
SP
JUL 5 , SAT
CH 4
STEREO
“Home video”
JUL 5 , MON
2:15 PM
Easy Information Screen
(Station ID)
PROGRAM DETAILS
“Home video”
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
Easy Information Screen
(Program details)
On-Screen Menus Setup
The SETUP, clock setting (CLOCK), and timer
recordings (PROGRAM) functions are accessed conveniently with the on-screen menus, that lead you through
each step. The following pages describe the on-screen
menu selections available.
Menu Selection
2:15 PM
2:15 PM
0:35:40
REM 1:58
otes
The function displays remain on the TV screen for 5
seconds.
The clock (or tape counter, tape remaining) mode will
continue to be shown until you press MEMORY/ENTER.
The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
Your VCR allows remote control adjustment of several
features.
Press MENU and the MAIN menu will appear.
1
Select the desired menu with v/V button and
2 then
press MEMORY/ENTER.
ote
Menus remain on-screen for 3 minutes.
MAIN MENU
CLOCK SET (page 18)
PROGRAM (page 24)
TUNING (page 17)
SETUP (page 17)
16
3 Press MENU when finished.
VCR Setup Menu Options
Channel Selection
1 Press MENU and the MAIN menu will appear.
v/V
V to select the SETUP menu, then press
2 Use
MEMORY/ENTER.
The SETUP menu will appear.
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Preparation:
Connect the DVD+Hi-Fi VCR to the desired type of antenna
or cable TV system, as shown in Connecting Antenna/Cable
TV to DVD+Hi-Fi VCR on page 11.
AUTO CHANNEL PROGRAMMING
v/V
V to choose a desired option on the
3 Use
B to choose a
SETUP menu. Then use b/B
desired setting.
1 Press MENU and the MAIN menu will appear.
v/V
V to select the TUNING menu, then press
2 Use
MEMORY/ENTER.
The TUNING menu will appear.
FUNCTION OSD
The on-screen display of this DVD+Hi-Fi VCR can be turned on or
off.
FUNCTION OSD: Choose ON and OFF with b/B.
LANGUAGE SELECT
The on-screen programming of this DVD+Hi-Fi VCR can be
displayed in either English, Spanish, or French.
LANGUAGE SELECT: Choose ENGLISH, SPANISH, or
FRENCH with b/B.
AUDIO MODE
The DVD+Hi-Fi VCR has two separate audio playback systems, the high quality VHS Hi-Fi system and standard NORMAL mono system. The same audio is generally recorded on
both systems. The VHS Hi-Fi system plays on separate (left
and right) channels, and the NORMAL system plays monaural
sound. The normal track is always played so the cassette can
be played on a DVD+Hi-Fi VCR that does not have VHS Hi-Fi.
AUDIO MODE: Choose Hi-Fi or NORMAL with b/B.
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the DVD+
Hi-Fi VCR automatically selects the corresponding receiving mode
(Stereo or SAP) regardless of the selected position. For normal
operation, the display should be in the STEREO position. The
DVD+Hi-Fi VCR will then record a STEREO program when available,
and record a mono program IF the program is NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.
BROADCAST TYPE: Choose STEREO, SAP, or MONO with
b/B.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT.
This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
AUDIO OUTPUT: Choose STEREO, LEFT, or RIGHT with
b/B.
4 Press MENU when finished.
V to choose the SOURCE SELECT option,
3 Use
B to select TUNER.
then use b/B
Press b/B repeatedly to switch among TUNER, LINE1 or
LINE2.
v/V
V to choose the AUTO CHANNEL SET option,
4 Use
B to search for channels.
then use b/B
The tuner will automatically cycle through all
available channels in the area and place them in
the tuner’s memory.
the AUTO CHANNEL SET PROCEEDING is
5 After
complete, make sure the TUNING BAND is set
appropriately (TV or CATV). Choose the correct
B while in
TUNING BAND (TV or CATV) with b/B
the TUNING menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection.
6 Press MENU to return to the TV screen.
v/V
V) on the front panel or CH/TRK
TUNING (v
7 (vUse
v/V
V) on the remote control to cycle the
DVD+Hi-Fi VCR through the channels in memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
1
Use V to choose the CH. ADD/DEL option on the
TUNING menu. Use b/B to select a channel to add
or erase.
2
Use MEMORY/ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3
Press MENU to remove menu.
17
SYSTEM SETUP
VCR Operation Setup (Continued)
VCR Operation Setup (Continued)
Setting the Clock
The DVD+Hi-Fi VCR gives you two ways to set the time
and date: the Auto Clock Feature or manually. The Auto
Clock feature enables the DVD+Hi-Fi VCR to set up the
clock while the DVD+Hi-Fi VCR is turned off.
Things to know before starting
The clock uses the 12-hour system. (Be sure to set AM
and PM correctly.) (AM does not appear.)
The initial Clock Setting is JANUARY 1, 2004, 12:00 AM.
Auto Clock Set
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVD+Hi-Fi VCR looks for a channel carrying
XDS (Extended Data Services) information. XDS updates the
clock using the Coordinated Universal Time.
ote
There are cases where the TV station does not send or sends
wrong date and/or time information and the DVD+Hi-Fi VCR
sets the incorrect time.
If this happens we recommend that you set the clock manually.
Manual Clock Set
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the CLOCK menu.
2 Use
Press MEMORY/ENTER and the CLOCK menu
will appear.
The Auto Clock feature enables the DVD+Hi-Fi VCR to
set up the clock while the DVD+Hi-Fi VCR is turned off.
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the CLOCK menu.
2 Use
Press MEMORY/ENTER and the CLOCK menu
will appear.
3 Use b/BB to choose the month.
V to choose the DAY option.
4 Use
B to choose the date.
Use b/B
The day of the week will display automatically.
V to choose the YEAR option.
5 Use
B to choose the year.
Use b/B
V to choose the TIME option.
6 Use
B to choose the time.
Use b/B
3
Use V to choose the AUTO CLOCK SET option.
B to choose ON.
Use b/B
The Auto Clock Set feature is set to ON at the factory. In
the ON setting, the DVD+VCR looks for a channel
carrying XDS (Extended Data Services) information. XDS
updates the clock using the Coordinated Universal Time.
Use to choose the DAYLIGHT SAVINGS
4 option.
E
Use
F
or
G
to choose AUTO, ON, or OFF.
7
Press and hold b/B to advance clock
continuously.
Use E to choose the DAYLIGHT SAVINGS
option.
Use F or G to choose AUTO, ON, or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR adjusts the clock for Daylight
Saving Time automatically.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR adjusts the clock for Daylight
Saving Time automatically.
Use
5 Use
to choose the TIME ZONE option.
or G to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
E
F
If “AUTO” is selected as the time zone, the VCR sets the
clock using the first Coordinated Universal Time information it finds in a broadcast signal.
6 Press MENU when finished.
off the DVD+Hi-Fi VCR and the auto clock
7 Turn
set feature sets the time.
18
8 Press MENU when finished.
ote
If setting the clock manually, “AUTO CLOCK SET”
must set to “OFF”.
If set to “ON”, an incorrect date and/or time will be
entered again when the DVD+Hi-Fi VCR is turned off.
DVD Operation Setup
General Explanation
Temporary Feedback Field Icons
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
1 Press DISPLAY during playback.
4 to select an item.
Press 3/4
2 The
selected item will be highlighted.
2 to change the setting of an item.
Press 1/2
3 The
number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
TITLE
Repeat Title
CHAPT
Repeat Chapter
GROUP
Repeat Group (DVD audio discs only)
TRACK
Repeat Track (non-PBC Video CDs and DVD
audio discs only)
ALL
Repeat All Tracks (non-PBC Video CDs only)
A B
Repeat A-B
OFF
Repeat Off
Resume play from this point
Action prohibited or not available
Notes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
press ENTER to execute the setting.
DVD-V
Items
4 to select desired item)
Function (Press 3/4
Title Number
1 /3
Chapter Number
1 /12
Time search
0:20:09
Audio language
and Digital Audio
Output mode
Subtitle language
1 ENG
D
5.1 CH
ABC
Angle
Sound
OFF
1 /1
BYPASS
Shows the current title number and total number of
titles, and skips to the desired title number.
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
Shows the elapsed playing time, and
searches the point directly from the elapsed time.
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and
changes the setting.
Selection Method
1 / 2, or
Numbers, ENTER
1 / 2, or
Numbers, ENTER, SKIP
Numbers, ENTER
1 / 2, or
AUDIO
1 / 2, or
SUBTITLE
1 / 2, or
ANGLE
1 / 2, or
SOUND MODE
19
SYSTEM SETUP
This manual gives basic instructions for operating the
DVD/CD receiver. Some DVDs require specific operation or allow only limited operation during playback.
When this occurs, the symbol
appears on the TV
screen, indicating that the operation is not permitted by
the DVD/CD receiver or is not available on the disc.
DVD Operation Setup (Continued)
On-Screen Display (Continued)
d
DVD-A
Items
4 to select desired item)
Function (Press 3/4
Group Number
Track Number
Time search
Subtitle language
Page (or Angle)
2 /6
Shows the current group number and total number
of groups, and skips to the desired group number.
1 / 2, or
Numbers, ENTER
1 /12
Shows the current track number and total number
of tracks, and skips to the desired track number.
1 / 2, or
Numbers, ENTER
0:10:15
DVD Audio
Output mode
1
PCM
5 CH
ABC
Shows the elapsed playing time.(Display only)
Shows the current encoding method, and channel
number, and changes the setting.
OFF
Shows the current subtitles language, and
changes the setting.
1 /12
Shows the current page (or angle) number and total number
of pages (or angle), and changes the page (or angle) number.
or
1 /1
20
Selection Method
_
1 / 2, or
AUDIO
1 / 2, or
SUBTITLE
1 / 2, or
ANGLE
DVD Operation Setup (Continued)
Picture
You can set your own Personal Preferences on the
DVD/CD receiver.
TV Aspect
General Operation
1
Press SETUP.
The setup menu appears.
DVD-A
4:3 Letterbox: Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a conventional TV set is
connected. The video material formatted in the Pan &
Scan style is played back in that style (Both sides of the
picture are cut off).
16:9 Wide: Select when a 16:9 wide TV is connected.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Country Code
Spanish
Disc Audio
4:3 Letterbox
TV Aspect
Italian
Disc Subtitle
4:3 Panscan
Menu Language
Chinese
Disc Menu
16:9 Wide
Progressive Scan
Polish
Rating
Hungarian
Country Code
5.1 Speaker Setup
Other — — — —
TV Aspect
Menu Language
Others
2
DVD-V
Progressive Scan
4 to select the desired item.
Press 3/4
The screen will show the current setting for the
selected item, as well as alternate setting(s).
the desired item is selected, press 2, then
3 While
3/4
4 to select the desired setting.
ENTER to confirm your selection.
4 Press
Some items require additional steps.
SETUP, RETURN, or PLAY to exit the
5 Press
setup menu.
Language
Disc Language
DVD-V
DVD-A
Select a language for the disc’s Menu, Audio, and
Subtitle.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to
enter the corresponding 4-digit number according to the language code list on page 43. If you enter the wrong language
code, press CLEAR.
5.1 Speaker Setup
Others
Progressive Scan
DVD-V
DVD-A
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks, but are connecting the
DVD Player to a standard (analog) television, set
Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
Disc Audio
Off
Disc Subtitle
On
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Country Code
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
5.1 Speaker Setup
Other — — — —
Hungarian
Others
Menu Language
Select a language for the setup menu. This is the menu
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
Country Code
5.1 Speaker Setup
Others
Caution
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to On in error, you must reset the unit.
1) Remove any disc from the unit and close the disc
tray. See that “NO DISC” is displayed on the display
window.
2) Press STOP and hold it for five seconds before
releasing it. The video output will be restored to the
standard setting and a picture will once again be
visible on a conventional analog TV or monitor.
TV Aspect
Menu Language
Progressive Scan
you see when you press SETUP.
21
SYSTEM SETUP
Initial Settings
DVD Operation Setup (Continued)
Speaker Setup
5.1 Speaker settings
Auto Play
DVD-V
DVD-A
Select speaker settings, including volume balance and
delay time, or test the speaker settings.
Speaker settings are only active on the Analog MultiChannel Output. (See “Speaker Setup”, page 38.)
DVD-V
DVD-A
You can set up the DVD/CD receiver so a DVD disc
automatically starts playing whenever the DVD is
inserted.
If Auto Play mode is set to On, this DVD/CD receiver
will search a title that playback time is longest and then
play back the title automatically.
On: Auto Play function is activated.
Off: Auto Play function is not activated.
Disc Audio
Disc Subtitle
Disc Menu
R
R
Rating
Front L
Country Code
Volume
TV Aspect
Menu Language
Progressive Scan
Size
Small
Distance
0.3 m
0 dB
Test
Return
5.1 Speaker Setup
Others
Others
The DRC, Vocal and Auto Play settings can be
changed.
4 to select the desired item and press
Press 3/4
ENTER. The setting of the selected item is changed
between On and Off.
Disc Audio
DRC
On
Disc Subtitle
Vocal
On
Disc Menu
PBC
On
Rating
Auto Play
Off
Country Code
TV Aspect
Menu Language
Progressive Scan
5.1 Speaker Setup
Others
Dynamic Range Control (DRC)
With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
Vocal
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
22
ote
The Auto Play function may not work for some DVDs.
DVD Operation Setup (Continued)
Parental Control
Country Code
Rating
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 44.).
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country-dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Select “Rating” on the Setup menu using the
3/4
4 buttons.
1
Disc Audio
8
Disc Subtitle
7
Disc Menu
6
Rating
Country Code
5
TV Aspect
Menu Language
Progressive Scan
3
4
2
1
Unlock
5.1 Speaker Setup
Change
Others
2 While “Rating” is selected, press 2.
you have not entered a password.
3 When
Enter a 4-digit password using the number buttons
to create a personal 4-digit security password. then
press MEMORY/ENTER. Enter the 4-digit password
again and press MEMORY/ENTER to verify.
When you have already registered a password;
Enter a 4-digit password using the numbered buttons to confirm the personal 4-digit security password, then press MEMORY/ENTER.
If you make a mistake before pressing MEMORY/ENTER,
press CLEAR and enter 4-digit security password again.
4
5
4 butSelect a rating from 1 to 8 using the 3/4
tons. One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the player, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
Press MEMORY/ENTER to confirm your rating
selection, then press SETUP to exit the menu.
ote
This function may not work for some DVDs.
Disc Audio
Code Set
Disc Subtitle
C SA
U
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
5.1 Speaker Setup
Others
4 buttons on
Select Country Code using the 3/4
1 the
setup menu.
2 While Country Code is selected, press 2.
3 Follow step 3 of “Rating” on left.
4 Select the first character using the 3/44 buttons.
Shift the cursor using 2 button and select the
5 second
4 buttons.
character using 3/4
Press MEMORY/ENTER to confirm your country
6 code
selection, then press SETUP to exit the
menu.
ote
Confirmation of the 4-digit password is necessary when
the code is changed (see “Changing the 4-digit code”
below.).
Changing the 4-digit code
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old code, then press MEMORY/ENTER.
4 buttons then press
3 Select Change using 3/4
MEMORY/ENTER.
4 Enter the new 4-digit code, then press MEMORY/
ENTER.
5 Enter exactly the same code a second time and
verify by pressing MEMORY/ENTER.
6 Press SETUP to exit the menu.
If you forget your 4-digit code
If you forget your password, to clear the current
password, follow the procedure below. (in the NO DISC
mode).
1 Press SET UP to display the Setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
The 4-digit password is cleared.
3 Enter a new code as shown above to the left
(Rating).
23
SYSTEM SETUP
DVD
DVD
VCR Operation
Normal Playback
Preparation:
Turn on the TV.
Tune the TV to the DVD+Hi-Fi VCR output channel (CH 3 or
4) or set the TV’s source selector to VIDEO.
If a direct VIDEO connection is made between the DVD+Hi-Fi
VCR and the TV, set the TV’s source selector to VIDEO.
Set the Output Source to VCR as shown in Setting the
Output Source on page 6.
1
Insert a prerecorded video cassette.
The
indicator will light and the DVD+Hi-Fi VCR will
power-up automatically.
Make sure that the
indicator in the display
window is not lighted. If it is, press POWER once.
If a tape without a safety tab is inserted, the unit will
start playback automatically.
Press PLAY ( ) once.
2 PLAY
appears on the TV screen .
B
It is not necessary to select the tape speed for
playback. It will be automatically selected by the
DVD+Hi-Fi VCR.
In playback, the TV/VCR selector switches to VCR
mode automatically.
x) to stop playback.
Press STOP (x
3 STOP
appears on the TV screen.
If the tape reaches the end before STOP (x) is
pressed, the DVD+Hi-Fi VCR will automatically stop,
rewind and eject the tape, and it will turn itself off.
Tracking Control
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
A tape is played back for the first time.
Tape speed (SP, LP, SLP) changes.
Streaks or snow appear because of scratches on the tape.
Manual Tracking
If noise appears on the screen during playback, press
V on the remote control until the noise
either CH/TRK v/V
on the screen is reduced.
If vertical jitter is present, adjust tracking controls very
carefully.
Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3
seconds.
Special Effect Playbacks
Special effects playback notes
Horizontal lines (noise bars) will appear on the TV screen.
This is normal.
The audio is automatically muted during special effect modes,
so there is no sound during search.
During high-speed picture search mode, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
Search
This function lets you quickly and visually search for a
desired tape section in either direction: forward or
reverse.
1 Press BACKWARD (.) or FORWARD (>)
during playback.
The DVD+Hi-Fi VCR will be activated in the SEARCH
mode.
If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+Hi-Fi VCR will automatically
enter the PLAY mode, to protect the tape and video
heads.
2 To return to playback, press PLAY ( B).
Still Picture and Frame-by-Frame Playback
1 Press PAUSE/STEP (X) during playback.
Picture movement will stop on one frame.
If the still picture vibrates vertically, stabilize it using
v/V on the remote control.
If the DVD+Hi-Fi VCR is left in the STILL mode for more
than 5 minutes, the DVD+Hi-Fi VCR will automatically
enter the STOP mode to protect the tape and video
heads.
2 Press PAUSE/STEP (X) repeatedly to advance the
video one frame at a time while viewing a still picture
in Still mode.
3 To return to playback, press PLAY ( B).
Slow Motion
1 While in Still mode, press FORWARD (>).
The tape will be played back at a speed 1/19 times
slower than the normal speed.
During slow playback, use v/V on the Remote Control to
minimize noise bands.
If slow motion mode continues for more than 3 minutes,
the DVD+Hi-Fi VCR will automatically change to playback
mode.
2 To return to playback, press PLAY ( B).
CM Skip (Commercial Skip)
ote
Only 2-channel stereo (Front Left, Front Right &
Subwoofer) is available for VCR mode, thus sound
might not be heard from center or rear speakers during
VCR playback. (For further details about sound mode,
please refer to page 15.)
This is useful for skipping commercials or short program
segments.
1 Press CM SKIP during playback.
The tape will fast forward picture search through 30
seconds of recording.
Skipping time can be extended by pressing CM SKIP
repeatedly.
Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 3
minutes).
2 When the search is complete, the DVD+Hi-Fi VCR
will go into playback mode automatically.
24
Normal Recording
Timer Recording
Preparation:
This DVD+Hi-Fi VCR can be programmed to record up to
8 programs within a period of 1 year. For unattended
recording, the timer needs to know the channels to be
recorded and the starting and ending times.
Turn on the power of both the DVD+Hi-Fi VCR and TV.
Tune the TV to the DVD+Hi-Fi VCR output channel (CH 3 or
4) or set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+Hi-Fi VCR and the TV, set the TV’s source selector to
VIDEO.
a video cassette with the anti erasure
1 Insert
safety tab intact.
2 Select the desired channel with v/VV.
3
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select LINE1 or
LINE2 with INPUT.
Set the desired recording speed (SP or SLP)
with SPEED.
This DVD+Hi-Fi VCR is not designed to record in LP
mode.
Things to know before starting
If you try to set the program timer before setting the clock,
PLEASE SET THE CLOCK appears for a moment and
then CLOCK menu appears on the TV screen. Set the time
and date before proceeding.
Make sure a tape is in the DVD+Hi-Fi VCR and the anti
erasure safety tab is in place or the tape will be automatically ejected.
Preparation:
Turn on the power of both the DVD+Hi-Fi VCR and the TV.
Be sure the TV is set to the DVD+Hi-Fi VCR output channel (3
or 4).
Make sure the TUNING BAND in the TUNING menu is set
appropriately (TV or CATV).
4 Set the MTS mode as desired (See page 17, 28).
Press MENU and the MAIN menu will appear.
z) once.
Press REC/ITR (z
1
5 Recording
will start. (The REC indicator will light in
the display window.)
2 Use v/VV to choose the PROGRAM menu.
MEMORY/ENTER to go to the PROGRAM
3 Press
menu.
The PROGRAM menu will appear.
x) twice to stop recording.
Press STOP (x
6
x
REC indicator appears only when the Output Source is
set to VCR.
If a cassette with no anti erasure safety tab is loaded,
the cassette will be ejected automatically.
If the tape reaches the end before STOP ( ) is pressed,
the DVD+Hi-Fi VCR will automatically stop, rewind, eject
the tape and turn itself off.
If all 8 programs have been entered, FULLY
PROGRAMMED message will appear for a moment
and then PROGRAM 1 will appear on the TV screen.
Pausing the recording
1 Press PAUSE/STEP (X) to pause the tape during
recording.
The REC indicator will flash in the display window.
2 When you want to continue recording, press
z).
PAUSE/STEP (X) or REC/ITR (z
After 5 minutes in Pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
To record one TV program while
watching another
1 Use TV/VCR to select the TV mode while recording.
The TV indicator appears.
2 Using the TV, select the channel to be viewed.
ips
Always use PAUSE/STEP (X) for best results when making
changes while recording.
For example: To change channels while recording, first press
PAUSE/STEP (X) to put the unit in pause mode. Select the
desired channel on the DVD+Hi-Fi VCR, then press
PAUSE/STEP (X) again to resume recording.
4 Use b/BB to choose the PROGRAM No. (1-8).
V to choose the MONTH option.
5 Use
B to choose the desired month.
Use b/B
Use V to choose the DAY option.
6 Use b/BB to choose the desired day.
V to choose the START option.
7 Use
B to choose the desired start time.
Use b/B
V to choose the STOP option.
8 Use
B to choose the desired stop time.
Use b/B
Use V to choose the CHANNEL option.
9 Use b/BB to choose the desired channel
(Channel, LINE1 or LINE2).
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD+Hi-Fi VCR (page
11), using a cable box converter, you must set the channel
in this step to match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box instead of
with the DVD+Hi-Fi VCR.
25
OPERATION
VCR Operation (Continued)
VCR Operation (Continued)
10
11
Use V to choose the SPEED option.
B to choose the desired recording
Use b/B
speed (AUTO, SP or SLP).
AUTO mode determines how much tape is left and
switches speed from SP to SLP, if necessary, to
complete recording the program. There will be some
picture and sound distortion at the point of the speed
change.
Use V to choose the REPEAT option.
B to choose the desired repeat (ONCE,
Use b/B
WEEKLY or DAILY).
ONCE event....for recording up to 8 programs on a
single day or over the days within a period of 1 year.
WEEKLY event....for recording up to 8 programs on a
certain day of every week.
DAILY event....for recording up to 8 programs at the
same time(s) Monday through Friday.
otes
If the power fails or the DVD+Hi-Fi VCR is unplugged
from the AC outlet, the correct clock time and timer settings are kept in memory for approximately 3 seconds.
After 3 seconds, the clock and program timer must be
reset when power is restored. Reset the clock according to instructions.
After timer recording is completed, the DVD+Hi-Fi VCR
will turn off automatically.
To watch a TV program while timer recording is in
progress, select Tuner mode by pressing TV/VCR
repeatedly.
If you wish to stop timer recording which has already started, press STOP or POWER twice.
Checking (Erasing) Timer Record
Programming
ip
If the input data is wrong, use v to select the data
B.
and correct it using b/B
12
Press MENU, the program will be memorized
by the DVD+Hi-Fi VCR.
indicator lights in the display window.
If the program preset time has past, the PAST TIME
PROGRAMMED message will appear on the TV
screen. Return to the incorrect program and program
it with the correct time.
If you had entered a past date, timer recording will
be performed on that date of the next year.
Additional programs may be entered by repeating
steps 1-12.
Cable Users: If your cable hookup is via a TV
converter box, you can program multiple recordings
only on the converter box output channel. This is
because the converter determines what channel you
view through your DVD+Hi-Fi VCR.
ip
If you are finished programming and you want to set the
DVD+Hi-Fi VCR to record the programs you have entered,
MAKE SURE YOU HAVE INSERTED A TAPE INTO THE
DVD+VCR. The DVD+Hi-Fi VCR is now set to record the preset programs.
After setting up a timer recording, recording will start if
no other timer recordings overlap the start time, see
next column.
26
Programming can be checked whenever the DVD+Hi-Fi
VCR is turned on.
1 Press MENU and the MAIN menu will appear.
2 Use v/V to choose the PROGRAM menu.
Press MEMORY/ENTER and the PROGRAM menu
will appear.
3 Use b/B to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press MENU to return to the TV screen.
Program Priority
If the recording start and
end times of preset
programs overlap on the
same day (see the example
and diagram left), program
number 2 will not be
recorded until program
number 1 is finished.
The first part of program number 2 will not be recorded.
The same thing will happen to program number 3.
Instant Timer Recording
Dubbing and Editing
Instant Timer Recording allows you to make a recording
easily of a preset length without using the programmable timer.
Preparation:
If you wish to edit or dub your camcorder (or another
VCR) recordings to this DVD+Hi-Fi VCR, the rear (or
Front) panel mounted Audio and Video (A/V) input
jacks make the connections quick and easy. These
direct A/V jacks will also provide better picture results
than using the RF jack on the rear panel.
Turn on the power of both the DVD+Hi-Fi VCR and the TV.
Be sure the TV is tuned to the DVD+Hi-Fi VCR output channel (3
or 4).
If a direct VIDEO/AUDIO connection is made between the
DVD+Hi-Fi VCR and the TV, set the TV’s source selector to
VIDEO.
1
V or number
the desired channel with v/V
2 Select
(0-9).
The channel number appears on the TV screen.
Insert a video cassette with the anti erasure
safety tab intact.
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select LINE1 or
LINE2. with INPUT.
1
Connect the camcorder’s (or another VCR’s) A/V
outputs to your DVD+Hi-Fi VCR as illustrated on page
13.
the input channel “LINE2”. (Use INPUT to
2 Set
select LINE2.)
If you have connected your DVD+Hi-Fi VCR to the A/V
input jacks on the rear of DVD+Hi-Fi VCR, you should
select the input channel LINE1 by pressing INPUT
twice.
the tape in the camcorder (or another
3 Play
VCR). If you have a TV attached to your
DVD+Hi-Fi VCR, you can see the video playing.
you desire the recording to begin, press
the desired recording speed (SP or SLP)
4 When
z) once to start.
DVD+Hi-Fi VCR’s REC/ITR (z
3 Select
with SPEED.
The tape speed will appear on the TV screen.
4 Press REC/ITR (zz) twice.
otes
The menu as illustrated, will appear on the TV screen.
Recording will start. (The
indicator will light)
z) repeatedly to select the
Press REC/ITR (z
5 recording
time length.
At the end of the recording, the DVD+Hi-Fi VCR will
stop recording and shut off.
While Instant Timer Recording is active, changing the
channel on the DVD+Hi-Fi VCR will not be possible.
To stop the recording, press STOP or POWER twice.
INSTANT TIMER RECORD MENU
INSTANT TIMER RECORD
CHANNEL
SPEED
2
SP
START
LENGTH
NOW
0H30M
0H30M ..... 9H00M ➝ 0H00M
Length Display
(each additional press of
z) increases recording
REC/ITR (z
time 30 minutes)
Checking the Recording Time
Press REC/ITR (z) once to check the recording time.
The recalled setting will automatically return to the TV
screen after 6 seconds.
To extend the Recording Time
The recording time can be extended anytime by pressing REC/ITR (z).
Subsequent presses result in advancing the recording
time by 30-minute increments.
otes
If you press PAUSE/STEP (X) while in instant timer recording mode, the DVD+Hi-Fi VCR will enter the recording pause
mode. Instant timer recording is cancelled.
If the DVD+Hi-Fi VCR is set to “0H00M”, the DVD+Hi-Fi
VCR goes to normal recording mode.
Before recording, please confirm the recording start position.
To stop the editing, press STOP (x) twice.
Copying from DVD to VCR
This unit is capable of copying the contents of a DVD
to a VHS tape.
ote
If the DVD you are attempting to copy is copy protected,
you will not be able to copy the disc. It is not permitted
to copy Macrovision encoded DVDs. “LOCK” is
displayed in the display window.
1
Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
VHS Tape
2 Insert
Insert a blank VHS video tape into the VCR deck.
Press PLAY ( ) on the DVD deck.
3 The
DVD will go into play mode
B
If the DVD disc menu appears, you may need to press
PLAY ( B) manually to begin copying.
z) on the front panel or remote
REC/ITR (z
4 Press
control.
The DVD+Hi-Fi VCR will go into Record mode.
“COPY” indicator will light.
5 Stop the Copy Process
When the DVD is finished playing, press STOP (x) or
POWER twice to end copying.
You must stop the Copy process manually when the DVD
movie ends, or the unit may replay and record over and
over again.
ote
When you stop the DVD playback during copying, VCR
recording mode also stops automatically.
27
OPERATION
VCR Operation (Continued)
VCR Operation (Continued)
VHS Hi-Fi Stereo System/
MTS Broadcast
MTS (Multi-Channel TV Sound)
This DVD+Hi-Fi VCR is equipped with the VHS Hi-Fi
audio sound system for recording and playback. The
information below gives a brief description of Hi-Fi audio
and how to record and play a tape in the Hi-Fi audio
mode.
1
Set the AUDIO MODE option to Hi-Fi on the
SETUP menu .
This DVD+Hi-Fi VCR will decode MTS stereo and bilingual (SAP) off-the-air broadcast sound signals. It also
decodes stereo TV sound from local cable companies,
as long as they operate on assigned cable frequencies
and use the EIA-recommended MTS stereo/bilingual TV
sound system.
Multichannel TV Sound Indicator (MTS)
Shows onscreen as illustrated below when MEMORY/
ENTER is pressed.
One or both of the indicators will light, depending on the
MTS broadcast.
TV screen
CH 4
STEREO/SAP
the AUDIO OUTPUT option to STEREO
2 Set
position.
(STEREO) POSITION: The left channel sound (L) is
heard from the left speaker and the right channel sound
(R) is heard from the right speaker.
(LEFT) POSITION: The left channel sound (L) is heard
from both speakers.
(RIGHT) POSITION: The right channel sound (R) is heard
from both speakers.
STEREO
Lights up when a stereo broadcast
is being received.
SAP
Lights up when a SAP BILINGUAL
broadcast is being received.
If only STEREO appears on the TV screen.
The DVD+Hi-Fi VCR can record in stereo onto the VHS Hi-Fi
audio tracks when the BROADCAST TYPE option is in the
STEREO position. The DVD+Hi-Fi VCR will also record mono
audio onto the mono audio track.
If only SAP appears on the TV screen.
Set the BROADCAST TYPE option to SAP.
If STEREO/SAP appears on the TV screen
Use the BROADCAST TYPE option to select the desired
recording mode (STEREO or SAP).
SAP (Second Audio Program) Recording
3 Press MENU.
a cassette and press PLAY (
4 Insert
Adjust volume at your stereo system.
B).
Some stations transmit a Second Audio Program, which
is used for a second language or additional information.
When the station broadcasts a Second Audio Program,
follow the procedure below to record the SAP.
Insert a video cassette with the anti erasure
safety tab intact.
1
the BROADCAST TYPE option to SAP
2 Set
(SETUP menu).
Do this if only the SAP appears on the TV screen or you
know the program will use the SAP.
3 Press MENU.
the desired recording speed (SP or SLP)
4 Select
with SPEED.
the desired channel. SAP should appear
5 Select
on the TV screen.
6 Press REC/ITR (zz) once
7 Press STOP (xx) twice to stop recording.
You are now recording the program you see and hear on the
TV.
28
VCR Operation (Continued)
Real-Time Counter
Shows length of tape run in hours, minutes, and
seconds. Press CLK/CNT to select the real-time
counter display.
Every press of CLK/CNT changes the TV screen display as illustrated below.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
REMAINING TIME
Counter changes to “0:00:00” when the cassette is
ejected.
The real-time counter does not operate if nothing is
recorded on the tape.
The real-time counter will not work unless a tape is
inserted.
Additional Information
In manual recording, Timer recording, Instant Timer
Recording, playback, or fast forward modes, the DVD+Hi-Fi
VCR automatically starts rewinding the tape at the end of
the tape. The cassette will stop at the beginning of the tape
and be ejected, and the DVD+Hi-Fi VCR will turn itself off.
After you have finished using the DVD+Hi-Fi VCR, rewind,
eject, and remove the cassette. Place the cassette in its
protective sleeve to protect it from dust. It is not necessary
to rewind the cassette before removing it, but if you do, it
will be ready to play or record the next time you use it.
Be sure the DVD+Hi-Fi VCR Channel Selector is on the
correct channel you wish to record. The channel that is
being recorded can always be checked by tuning the television to the DVD+Hi-Fi VCR channel (3 or 4) and using the
TV/VCR selector to turn the DVD+Hi-Fi VCR’s TV indicator
off.
Do not attempt to hook up more than one television set to
the DVD+Hi-Fi VCR for either recording or playback.
Counter Memory Feature
Auto Play System
This is useful if there is a section of tape you want to
view immediately after recording or if you want to return
to the same point several times.
This DVD+Hi-Fi VCR features automatic playback.
Load a cassette (with the safety tab removed).
1
CLK/CNT repeatedly to display the
2 Press
real-time counter on the TV screen.
the point that you want to locate later, reset
3 Atthe
real-time counter to “0:00:00” by pressing
CLEAR.
Begin recording or playing a tape.
4 Continue to play or record.
x) once or twice when recording
STOP (x
5 orPress
playback finishes.
.).
BACKWARD (.
6 Press
The tape automatically stops when the tape counter
returns to about “0:00:00”.
The Output Source is changed to VCR mode automatically.
The power turns on automatically and playback begins.
At the end of the tape, the DVD+Hi-Fi VCR stops and
rewinds the tape.
The cassette is ejected after rewinding and the VCR turns
itself off automatically.
LOAD
AUTO
AUTO
PLAY
TAPE
AUTO
REWIND
EJECT
AUTO
POWER
OFF
ote
Auto power off does not function during regular DVD play
mode. (DVD+Hi-Fi VCR power stays on.)
Tape Remaining
This function shows the remaining time on the tape
during recording or playback.
Press CLK/CNT repeatedly until the REM indicator
appears on the TV screen during recording or playback.
ote
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc.)
29
OPERATION
Tape Counter Memory Feature
DVD Operation
Playing a DVD
Playback Setup
General Features
DVD-V
DVD-A
Turn on the TV and select the video input source connected to the DVD/CD receiver.
Audio system: Turn on the audio system and select
the input source connected to the DVD/CD receiver.
1 Press OPEN/CLOSE to open the disc tray.
your chosen disc in the tray, with the
2 Load
playback side facing down.
OPEN/CLOSE to close the tray.
3 Press
READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY.
In some cases, the disc menu might appear
instead.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD which offers a menu.
DVD-V
Use the 1 234 buttons to select the title/chapter you
want to view, then press ENTER to start playback.
Press TITLE or MENU to return to the menu screen.
DVD-A
Use the 1 2 3 4 buttons to select an option you
want, then press ENTER to view the option.
otes
– If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 23).
– DVDs may have a regional code.
Your receiver will not play discs that have a regional
code different from your receiver. The regional code
for this receiver is 1 (one).
ote
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
Moving to another TITLE /GROUP
DVD-V
DVD-A
1 /3
1/6
When a disc has more than one title/group, you can
move to another title as follows:
Press DISPLAY, then press the appropriate number
button (0-9) to select a title/group number.
Moving to another CHAPTER/TRACK
DVD-V
DVD-A
1 /12
1 /3
1/6
1 /12
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
Press SKIP/SCAN . or > briefly during
playback to select the next chapter/track or to return to the
beginning of the current chapter/track.
Press . twice briefly to step back to the previous chapter/group/track.
To go directly to any chapter during DVD playback, press
4 to select the
DISPLAY. Then, press 3/4
chapter/group/track icon. Then, enter the chapter/track
number using the numbered buttons (0-9).
ote
For two-digit numbers, press the numbered buttons
(0-9)in rapid succession.
Search
DVD-V
1 Press and hold SKIP/SCAN . or > for about
two seconds during playback.
The receiver will now go into SEARCH mode.
2 Press and hold SKIP/SCAN . or > repeatedly
to select the required speed: mX2, mX4, mX16,
mX100 (backward) or MX2, MX4, MX16,
MX100 (forward).
3 To return to normal play, press PLAY.
ote
When using a DVD audio disc that includes pictures,
this operation may be permitted in some picture
segments.
Pause
DVD-V
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY.
30
DVD Operation (Continued)
Still Picture and Frame-by-frame playback
DVD-V
1 Press PAUSE/STEP during playback.
The DVD/CD receiver will now go into PAUSE mode.
2 You can advance the picture frame-by-frame by
pressing PAUSE/STEP repeatedly on the remote control.
3 To return to normal play, press PLAY.
DVD Audio Discs - Repeat Track/Group/Off
1 To repeat the currently playing track, press REPEAT.
The Repeat Track icon appears on the TV screen.
2 To repeat the group currently playing, press REPEAT
a second time.
The Repeat Group icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Time Search
ote
When using a DVD audio disc that includes pictures,
this operation may be permitted in some picture
segments.
Slow Motion
The player will enter SLOW mode.
2 Use the SLOW SCAN t or T to select the required
speed: t 1/16, t 1/8, t 1/4 or t 1/2 (backward),
or T 1/16, T 1/8, T 1/4 or T 1/2 (forward).
3 To exit slow motion mode, press PLAY.
A *
0:20:09
-:--:--
The Time Search function allows you to start playing at
any chosen time on the disc.
1 Press DISPLAY during playback. The on-screen display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
DVD-V
1 Press SLOW SCAN t or T during playback.
Repeat A-B
DVD-V
4 to select the Time
2 Within 10 seconds, press 3/4
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
3 Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes, and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
DVD-V
A B
4 Within 10 seconds, press ENTER to confirm the start
time.
OFF
To repeat a sequence in a title or group:
1 Press REPEAT A-B at your chosen starting point.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
“ A * ” appears briefly on the TV screen.
2 Press REPEAT A-B again at your chosen end point.
“A B” appears briefly on the TV screen, and the repeat
sequence begins (“AsB” appears the display window).
3 To cancel the sequence, press REPEAT A-B.
Repeat
CHAPT
DVD-V
TITLE
1/6
OFF
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
31
OPERATION
General Features (continued)
DVD Operation (Continued)
General Features (continued)
3D Surround
DVD-V
BYPASS
3 Press CLEAR.
The Marker number will be erased from the list.
3D SUR
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press SOUND MODE to select “3D SUR” during
playback.
2 To turn off the 3D Surround effect, press SOUND
MODE again to select “BYPASS”.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
Special DVD Features
DVD-V
Checking the contents of DVD Video
discs: Menus
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
DVDs may offer menus that allow you to access special
features. To use the disc menu, press MENU. Then,
press the appropriate number button to select an option.
Or, use the 1 234 buttons to highlight your selection,
then press ENTER.
1 Press ZOOM during playback or still playback to
activate the Zoom function.
Title Menu
If you press ZOOM repeatedly, the magnification level
increases up to six steps.
1 Press TITLE.
Zoom
DVD-V
2 Use the 1 234 buttons to move through the zoomed
picture.
3 Press CLEAR to resume normal playback or return to
the paused image.
ote
The zoom function may not work for some DVDs.
Marker Search
1/9
DVD-V
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press TITLE again.
Disc Menu
DVD-V
1 Press MENU.
The disc menu is displayed.
DVD-V
2 To remove the disc menu, press MENU again.
MARKER SEARCH
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when
playback reaches the spot that you want to
memorize.
Camera Angle
1 /1
DVD-V
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
Changing the Audio Language
To Recall a Marked Scene
Press AUDIO repeatedly during playback to hear a different audio language or audio track.
1 During disc playback, press SEARCH.
DVD-V
DVD-A
1 ENG
D
5.1 CH
1
PPCM
5 CH
The MARKER SEARCH menu will appear on the screen.
2 Within 10 seconds, press 1/2 to select a Marker
number that you want to recall.
3 Press ENTER.
Playback will start from the Marked scene.
Subtitles
If
The MARKER SEARCH menu will appear on the screen.
2 Press 1/2 to select the Marker number that you want
to erase.
32
DVD-A
ABC
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
4 To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1 During disc playback, press SEARCH.
DVD-V
ote
appears, the feature is not available on the disc.
DVD Operation (Continued)
DVD-A
Viewing another PAGE
DVD Audio is a new disc format building on the success
of DVD to provide high quality, uncompressed, multichannel audio for a new experience in audio quality. A
DVD Audio disc can be identified by the DVD audio logo
on the disc jacket or on the disc itself.
DVD Audio can provide higher quality stereo than Audio
CDs with a sampling rate of up to 192kHz (compared to
44.1kHz for CDs). DVD Audio digital sound can be
delivered with up to 24 bits of data (compared to 16 bits
for a standard CD).
A typical DVD Audio disc contains up to seven times the
data capacity of a CD. This additional space is used for
music, either Advanced Resolution multi-channel sound
quality that is closer to the artist’s master recording or
for longer recordings. Many DVD Audio discs contain
on-screen text, such as artist biographies, playlists, or
lyrics. Some DVD Audio discs contain photo galleries or
video clips.
DVD-A
1 /12
Since DVD Audio discs can hold a lot of content, there
are various ways to see what’s available on the disc.
1 Press DISPLAY during playback.
4 to select Page icon.
2 Press 3/4
3 Press 1/2 to select a page number.
What appears on the screen will vary from disc to disc
because the information available depends upon the way the
disc was created.
ote
Since the authoring of DVD Audio Discs varies, some of
the on-screen display choices might not be available for
the disc you’re playing.
ote
If you use the DIGITAL OUT (OPTICAL) for your audio
connection, the sound will only be similar to CD-quality
sound even though you’re playing a DVD Audio disc.
Moving to another GROUP
DVD-A
1/6
Some DVD Audio discs divide content into different
groups. Your player enables you to quickly access different groups during playback via the on-screen display.
1 Press DISPLAY during playback on in stop mode.
4 to select Group icon.
2 Press 3/4
3 Press 1/2 or the numbered buttons (0-9) to select a
group number.
ote
Sometimes the author of the disc creates hidden content that can only be accessed by entering a password.
If the lock icon appears on the TV screen, enter the
password (sometimes you’ll find it on the disc’s jacket
cover or on a web site). This password control isn’t dictated by your DVD/CD receiver — it is a function of the
disc.
Since the authoring of DVD Audio Discs varies, some of
the on-screen display choices might not be available for
the disc you’re playing.
33
OPERATION
DVD Audio Discs
Audio and MP3/WMA Disc Operation
Playing an Audio CD and MP3/WMA Disc
CD
MP3
About MP3
WMA
The DVD/CD receiver can play MP3/WMA formatted
recordings on CD-ROM, CD-R or CD-RW discs.
Before playing MP3/WMA recordings, read the notes on
MP3/WMA Recordings on right.
1
Insert a disc and close the tray.
Audio CD; Audio CD menu appears on the TV
screen go to step 4.
MP3/WMA disc; The MP3/WMA-JPEG choice
menu appears on the TV screen. Go to step 2
MP3 WMA
JPEG
4 to select the MP3/WMA then press
Press 3/4
2 ENTER.
The MP3/WMA menu appears on the TV screen.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
MP3 WMA
Program
Folder1
Folder2
Folder3
Folder4
Folder5
Folder6
Folder7
Folder8
00:00
Clear All
OFF
3/4
4 to select a folder, and ENTER.
3 Press
A list of files in the folder appears.
4 to select a track then press PLAY or
Press 3/4
4 ENTER.
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window and menu.
Playback will stop at the end of the disc.
Press TITLE to move to the next page.
Press MENU to move to the previous page.
Program
CD
Program
MP3 WMA
TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
TRACK07
Clear All
TRACK08
0: 56: 18
STER.
BYPASS
Audio CD menu
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
Clear All
1
An MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
The player can not read an MP3 file that has a file
extension other than “.mp3”.
About WMA(Window Media Audio)
An WMA file is a Microsoft audio compression
technology.
WMA(Windows Media Audio) offers double the audio
compression of the MP3 format.
MP3/WMA Disc compatibility with this DVD/CD
receiver is limited as follows:
1. Sampling Frequency / only at 44.1kHz (MP3),
32 - 44.1kHz (WMA)
2. Bit rate / within 32 - 320kbps (MP3),
32 - 128kbps (WMA)
3. CD-R physical format should be “ISO 9660”
4. If you record MP3/WMA files using the software
which cannot create a FILE SYSTEM, for example
“Direct-CD” etc., it is impossible to playback
MP3/WMA files. We recommend that you use “EasyCD Creator”, which creates an ISO9660 file system.
5. A single session disc requires MP3/WMA files in the
first track. If there is no MP3/WMA file in the 1st
track, it cannot playback MP3/WMA files. If you wish
to playback MP3/WMA files, format all the data in
the disc or use a new one.
6. File names should be named using 8 letters or less
and must incorporate “.mp3” or “.wma” extension
e.g. “********.MP3” or “********.WMA”.
7. Do not use special letters such as “/ : * ? “ < > ” etc.
8. Total number of files on the disc should be less than
650.
This DVD/CD receiver requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 or WMA files). That require certain pre-existing
conditions (see above) to insure compatible playback.
OFF
MP3/WMA menu
ip
If you are in a file list and want to return to the Folder
4 to highlight
list, use the 3/4
and press ENTER to
return to the previous menu screen.
5 To stop playback at any other time, press STOP.
34
Notes on MP3/WMA Recordings
Customers should also note that permission is
required in order to download MP3/WMA files and
music from the Internet. Our company has no right
to grant such permission. Permission should
always be sought from the copyright owner.
Audio and MP3/WMA Disc Operation (Continued)
CD
MP3
Repeat A-B
WMA
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
CD
To repeat a sequence.
1 During disc playback, press REPEAT A-B at your chosen starting point.
The Repeat icon and “A * ” appears on the menu screen.
Moving to another Track
CD
MP3
WMA
Press SKIP/SCAN . or > briefly during
playback to go to the next track or to return to the
beginning of the current track.
Press SKIP/SCAN . twice briefly to step back to
the previous track.
In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
Repeat Track/All/Off
CD
MP3
WMA
1 To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the menu
screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat icon and “ALL” appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and “OFF” appears on the menu screen.
Search
CD
MP3
2 Press REPEAT A-B again at your chosen end point.
The Repeat icon and “A B” appears on the menu screen,
and the sequence begins to play repeatedly.
3 To exit the sequence and return to normal play, press
REPEAT A-B again.
The Repeat icon and “OFF” appears on the menu screen.
3D Surround
CD
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press SOUND MODE to select “3D SUR” during playback.
2 To turn off the 3D Surround effect, press SOUND
MODE again to select “BYPASS.”.
Changing the Audio Channel
CD
Press AUDIO repeatedly during playback to hear a
different audio channel (STER., LEFT, or RIGHT).
WMA
1 Press and hold SKIP/SCAN . or > for about
two seconds during playback.
The player will now go into SEARCH mode.
2 Press and hold SKIP/SCAN . or > repeatedly
to select the required speed: mX2, mX4, mX8
(backward) or MX2, MX4, MX8 (forward).
Search speed and direction are indicated on the menu
screen.
3 To exit SEARCH mode, press PLAY.
35
OPERATION
Pause
JPEG Disc Operation
Viewing a JPEG disc
Moving to another File
JPEG
This DVD/CD receiver can play discs with JPEG files.
Before playing JPEG recordings, read the notes on
JPEG Recordings on right.
1
Insert a disc and close the tray.
The MP3/WMA-JPEG choice menu appears on the
TV screen.
Press SKIP/SCAN . or > once during viewing a
picture to advance to the next file or to the previous file.
Still Picture
1 Press PAUSE/STEP during slide show.
The DVD/CD receiver will now go into PAUSE mode.
2 To return to the slide show, press PLAY or press
PAUSE/STEP again.
MP3 WMA
To flip the picture
JPEG
2
4 to select the JPEG then press
Press 3/4
ENTER.
The JPEG menu appears on the TV screen.
4 during showing a picture to flip the
Press 3/4
picture horizontally or a vertically.
To rotate picture
JPEG
Press 1/2 during showing a picture to rotate the
picture clockwise or counter clockwise.
Folder1
Folder2
Folder3
Folder4
Folder5
Folder6
Notes on JPEG Recordings
Folder7
Folder8
Slide Speed
3
Off
4 to select a folder, and ENTER.
Press 3/4
A list of files in the folder appears.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
Tip
If you are in a file list and want to return to the Folder
list, use the 34 buttons on the remote to highlight
“
” and press ENTER to return to the
previous menu screen.
4
4 to
If you want to view a particular file, press 3/4
highlight a file and press ENTER or PLAY.
Viewing the file proceeding starts.
During viewing a file, press RETURN to move to
the previous menu (JPEG menu).
Press TITLE to move to the next page.
Press MENU to move to the previous page.
JPEG
Folder1
Picture1
Picture2
Picture3
Picture4
Picture5
Picture6
Picture7
5/32
1024X768
Slide Speed
Off
5/32
1024X768
Picture5.jpg
ip
There are three viewing Slide Speed options: Fast,
Normal, Slow, and Off. Press 1/2 to highlight the Slide
Speed then press 3/4 to select the option you want to
use, and press ENTER.
viewing at any other time, press STOP.
5 ToThestop
JPEG menu appears.
36
Depending upon the size and number of the JPEG
files, it could take a long time for the DVD/CD receiver to read the disc’s contents. If you don’t see an onscreen display after several minutes, some of the files
are too big — reduce the resolution of the JPEG files
to less than 2 mega pixels and burn another disc.
Total number of files and folders on the disc should
be less than 650.
Some disc may be incompatible due to different
recording format or condition of disc.
When you are using software such as “Easy CD
Creator” to burn the jpeg files into the CD-R, ensure
that all the selected files have the “.jpg” extensions
when copying into the CD layout.
If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” files.
File names without “.jpg” extension will not be able to
be read by this DVD/CD receiver. Even though the
files are shown as JPEG image files in windows
explorer.
CD
MP3
Programmed Playback with Audio CD
and MP3/WMA Disc
The Program function enables you to store your favorite
tracks from any disc in the player memory.
WMA
Repeat Programmed Tracks
To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the menu
screen.
To repeat all tracks on the program list, press
REPEAT a second time.
Program can contain 30 tracks.
The Repeat icon and “ALL” appears on the menu screen.
1
Press PROGRAM during playback or in the stop
mode to enter the Program Edit mode.
The E mark will appear to the right of the word Program
on the right side of the menu screen.
ote
Press PROGRAM to exit the Program Edit mode;
the E mark will disappear.
Program
TRACK 1
TRACK 12
TRACK 2
TRACK 8
TRACK 3
TRACK 10
TRACK 4
TRACK 3
E
TRACK 5
TRACK 6
TRACK 7
Clear All
TRACK 8
0: 56: 18
STER.
BYPASS
Audio CD menu
Program
MP3 WMA
E
TRACK 8.mp3
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
TRACK 2.mp3
TRACK 4.mp3
TRACK 3.mp3
Clear All
3
The Repeat icon and “OFF” appears on the menu screen.
Erasing a Track from Program List
1 Press PROGRAM during playback (Audio CD and
MP3/WMA disc only) or in the stop mode to enter the
Program Edit mode.
The
a track, then press ENTER to place the
2 Select
selected track on the Program list.
step 2 to place additional tracks on the
3 Repeat
Program list.
CD
To cancel Repeat mode, press REPEAT a third time.
E
mark will appear.
2 Press 2 to move to the Program list.
4 to select the track that you wish to erase
3 Use 3/4
from the Program list.
4 Press CLEAR.
The track will be erased from the Program list.
Erasing the Complete Program List
1 Follow steps 1-2 of “Erasing a Track from Program
List” as above.
4 to select “Clear All”, then press ENTER.
2 Use 3/4
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
OFF
MP3/WMA menu
4 Press 2.
The programmed track you selected last is highlighted on
the program list.
4 to select the track you want to start
Press 3/4
5 playing.
Press TITLE to move to the next page.
Press MENU to move to the previous page.
6 Press PLAY to start.
Playback begins in the order in which you programmed
the tracks and “PROG.” appears on the menu screen.
Playback stops after all of the tracks on the Program list
have played once.
7
To resume normal playback from programmed playback, select a track of CD (or
MP3/WMA) list and then press ENTER.
“PROG.” indicator disappears on the menu screen.
37
OPERATION
Programmed Playback
Speaker Setup
Adjust the Speaker Setup menu option settings for the
built-in 5.1 channel surround decoder. (Also refer to
page 14, Speaker Positioning.)
Speaker Selection
Select a speaker that you want to set up. ((Front speakers (Left), Front speakers (Right), Center Speaker, Rear
speakers (Left), Rear speakers (Right), Subwoofer))
Disc Audio
Disc Subtitle
Disc Menu
R
Rating
Front L
Country Code
Volume
TV Aspect
Menu Language
Progressive Scan
Size
Distance
R
0 dB
Small
1 ft
Test
Return
5.1 Speaker Setup
Others
1
“5.1 Speaker Setup” is selected, press 2
2 While
button.
3 Use 2 button to select the desired speaker.
4 Adjust options by using 341 2 buttons.
Select “5.1 Speaker Setup” on the Setup menu
4 buttons.
using the 3/4
ote
Certain speaker settings are prohibited by the Dolby
Digital licensing agreement.
Volume
Use 1 / 2 to adjust the output level of the selected
speaker. (-6dB ~ +6dB)
Size
Speaker size settings are fixed, you cannot change the
settings.
Distance
If you connected speakers to your DVD+Hi-Fi VCR,
specify the Distance from each speaker to the listener,
you want to make the sound from each speaker reach
the listener at the same time. (1 ft = 30.48 cm)
ote
You can not set the distance of subwoofer speaker.
Test
Press MEMORY/ENTER to test the signals of each
speaker. Adjust the volume to match the volume of test
signals memorized in the system.
Front Left (L) → Front Right (R) → Center →
Rear Left (L) → Rear Right (R) → Subwoofer
Return
Press MEMORY/ENTER to return to the previous menu.
38
Presetting the Radio Stations
Listening to the Radio
You can preset 50 stations for FM and AM. Before tuning, make sure that you have turned down the volume.
Preset radio stations in the DVD/VCR Receiver memory
first (see “Presetting Radio Stations” on the left).
1
1
Press FM/AM on the remote control or RADIO
on the front panel until the frequency band
appears on the display and TV screen.
Press FM/AM on the remote control or RADIO
on the front panel until the frequency band
appears on the display and TV screen.
The last received station is tuned in.
- - - - - - - RADIO - - - - - - - 1/10
AM
AM
AM
AM
AM
530kHz
1720kHz
600kHz
1400kHz
1000kHz
FM/AM
MEMORY/CLEAR
Each time you press the button, the DVD/VCR Receiver
tunes in one preset station at a time.
TUNING
3/4
4 on the remote control or CH/PRESET
2 Use
3/4
4 front panel to select the desired Station.
If you select a blank column, R-SKIP appears in the display window.
- - - - - - - RADIO - - - - - - - 2/10
FM 87 . 5MHz
FM 108 . 0MHz
FM 90 . 0MHz
FM 106 . 0MHz
FM 98 . 0MHz
FM/AM
MEMORY/CLEAR
3/4
4 on the remote control repeatedly to
2 Use
select the preset station you want.
the volume by rotating VOLUME on the
3 Adjust
front panel or by pressing VOLUME 3 or 4 on
the remote control repeatedly.
To Clear the Stored Radio Stations
1
Press FM/AM on the remote control or on the
front panel until the frequency band appears on
the display and TV screen.
- - - - - - - RADIO - - - - - - - 1/10
TUNING
AM
AM
AM
AM
AM
530kHz
1720kHz
600kHz
1400kHz
1000kHz
FM/AM
MEMORY/CLEAR
TUNING
3
4 on the remote control to select your
Use 3/4
4/3
3) on the remote control
Hold down TUNING (4
2
desired station.
4 for
1 or 2 seconds, and a station is searched for
automatically.
Press FM/AM on the remote control or front
panel to select the desired band.
- - - - - - - RADIO - - - - - - - 2/10
5
Press MEMORY on the remote control.
The station is stored.
FM 87 . 5MHz
FM 108 . 0MHz
FM 90 . 0MHz
FM 106 . 0MHz
FM 98 . 0MHz
FM/AM
MEMORY/CLEAR
6
Repeat steps 2 to 5 to store other stations.
TUNING
CLEAR the remote control to clear the
3 Press
stored radio station.
- - - - - - - RADIO - - - - - - - 6/10
FM 87 . 0MHz
FM/AM
TUNING
ote
While record or record pause mode, the CLEAR
function may not be operated.
39
OPERATION
Radio Operation
Radio Operation (Continued)
Tuning Stations Manually
Labeling Stations
1
You can enter a name of up to 5 characters for preset
stations. The names (for example, “ABCD”) appears in
the system’s Display window when a station is selected.
Note that no more than one name can be entered for
each preset station.
Press FM/AM on the remote control or on the
front panel until the frequency band appears on
the display and TV screen.
FM/AM on the remote control or on the
2 Use
front panel to select the desired band.
Use 4 TUNING 3 on the front panel or press
3 desired
1 and 2 on the remote control to tune in the
station.
1
Press 2 to move to the station name column.
- - - - - - - RADIO - - - - - - - 6/10
For your reference
To turn the radio off
Press POWER to turn the DVD+Hi-Fi VCR off or select
another function mode (CD/DVD, VCR, LINE 1 or
LINE 2).
Tuning Stations Automatically
Hold down 4 TUNING 3 on the front panel for 1 or 2
seconds, and the next station is searched for automatically.
ote
The search may not tune in or stop at a station with a
very weak signal.
Mute
Press MUTE to remove the sound.
You can mute your unit in order, for example, to answer
the telephone, “MUTE” indicator flashes in the display.
Press MUTE again to restore sound.
40
FM 87 . 5MHz
FM 108 . 0MHz
FM 90 . 0MHz
FM 106 . 0MHz
FM 98 . 0MHz
FM/AM
MEMORY/CLEAR
TUNING
4 buttons to select the character then
the 3/4
2 Use
2 buttons to shift to the next or previuse the 1 /2
ous character.
3 Press ENTER to confirm the station name.
4 Press ENTER on the remote control.
The station name is stored.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Correction
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD+Hi-Fi VCR
does not work.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture.
The TV is not set to receive DVD+Hi-Fi
VCR signal output.
Select the appropriate video input mode
on the TV so the picture from the
DVD+Hi-Fi VCR appears on the TV
screen.
TV/VCR mode for DVD+Hi-Fi VCR is
set to TV.
Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. TV indicator disappears from the
display window.
The video cable is not connected
securely.
Connect the video cable securely.
The connected TV power is turned off.
The Digital Audio Output is set to the
wrong position.
Turn on the TV.
The disc is dirty.
Clean the disc.
Tape heads are dirty.
Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use CH/TRK (v/V) for manual tracking
adjustment while tape is playing.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, color system, and Regional code.)
The disc is placed upside down.
Place the disc with the playback side down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
The remote control is not pointed at the
remote sensor of the DVD+Hi-Fi VCR.
Point the remote control at the remote
sensor of the DVD+Hi-Fi VCR.
The remote control is too far from the
DVD+Hi-Fi VCR.
Operate the remote control within 23 ft
(7 m).
There is an obstacle in the path of the
remote control and the DVD+Hi-Fi VCR.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
This remote control uses the same
buttons for VCR and DVD functions
(ex. PLAY).
When using a VCR tape, first press the
VCR button. When using a DVD, first
press the DVD button.
No sound.
The playback picture is
poor.
The DVD+Hi-Fi VCR
does not start playback.
The remote control
does not work properly.
Set the Digital Audio Output to the
correct position, then turn on the
DVD+Hi-Fi VCR again by pressing
POWER.
41
REFERENCE
Symptom
Troubleshooting (Continued)
Symptom
Cause
Correction
Some channels are
skipped over when
using CH/TRK (v/V)
Those channels were deleted with the
CH. ADD/DEL option.
Use CH. ADD/DEL. to restore channels.
See “Channel Selection” on page 17.
Picture and sound of
broadcasting channel
are weak or missing.
Antenna or cables are loose.
Tighten connections or replace cable.
Wrong TUNING BAND option is being
used.
Try all TUNING BAND options. See
“Channel Selection” on page 17 for
details.
Camcorder image via
A/V input to DVD+Hi-Fi
VCR is not shown on
TV screen.
DVD+Hi-Fi VCR SOURCE SELECT is
not set to LINE1 or LINE2.
Use INPUT to select LINE input
source (LINE1 or LINE2).
Timer recording is not
possible.
Clock in DVD+Hi-Fi VCR is not set to
correct time.
Set clock to correct time. See “Setting
the Clock” on page 18.
Timer has been programmed
incorrectly.
Reprogram Timer. See “Timer
Recording” on pages 25 and 26.
indicator does not appear after programming timer.
Reprogram Timer.
indicator appears
after DVD+Hi-Fi VCR is
turned off.
DVD+Hi-Fi VCR is in Timer Recording
mode.
This is the normal indication that the
DVD+Hi-Fi VCR is in TIMER mode.
Stereo Audio Record
and/or Playback is not
present.
TV is not Stereo-compatible.
No action is possible.
Broadcast program is not in stereo format.
No action is possible.
DVD+Hi-Fi VCR BROADCAST TYPE
mode is set to SAP or MONO.
Set BROADCAST TYPE mode to
STEREO. See “Setting the VCR Setup
Menu” on page 17.
Moisture Condensation
Moisture condensation can occur:
In locations where moisture condensation may occur:
• When the DVD+Hi-Fi VCR is moved from a cold
place to a warm place.
• Keep the DVD+Hi-Fi VCR plugged into an AC power
outlet with POWER On. This will help prevent condensation.
• Under extremely humid conditions.
• When condensation has occurred, wait a few hours
for the DVD+Hi-Fi VCR to dry before using it.
42
Language Code List
Language
Code
Language
Code
Language
Code
Language
Code
Abkhazian
6566
Fiji
7074
Lingala
7678
Singhalese
8373
Afar
6565
Finnish
7073
Lithuanian
7684
Slovak
8375
Afrikaans
6570
French
7082
Macedonian
7775
Slovenian
8376
Albanian
8381
Frisian
7089
Malagasy
7771
Somali
8379
Amharic
6577
Galician
7176
Malay
7783
Spanish
6983
Arabic
6582
Georgian
7565
Malayalam
7776
Sudanese
8385
Armenian
7289
German
6869
Maltese
7784
Swahili
8387
Assamese
6583
Greek
6976
Maori
7773
Swedish
8386
Aymara
6588
Greenlandic
7576
Marathi
7782
Tagalog
8476
Azerbaijani
6590
Guarani
7178
Moldavian
7779
Tajik
8471
Bashkir
6665
Gujarati
7185
Mongolian
7778
Tamil
8465
Basque
6985
Hausa
7265
Nauru
7865
Tatar
8484
Bengali; Bangla
6678
Hebrew
7387
Nepali
7869
Telugu
8469
Bhutani
6890
Hindi
7273
Norwegian
7879
Thai
8472
Bihari
6672
Hungarian
7285
Oriya
7982
Tibetan
6679
Breton
6682
Icelandic
7383
Panjabi
8065
Tigrinya
8473
Bulgarian
6671
Indonesian
7378
Pashto, Pushto
8083
Tonga
8479
Burmese
7789
Interlingua
7365
Persian
7065
Turkish
8482
Byelorussian
6669
Irish
7165
Polish
8076
Turkmen
Cambodian
7577
Italian
7384
Portuguese
8084
8475
Catalan
6765
Japanese
7465
Quechua
8185
Twi
8487
Chinese
9072
Javanese
7487
Rhaeto-Romance 8277
Ukrainian
8575
Corsican
6779
Kannada
7578
Romanian
8279
Urdu
8582
Croatian
7282
Kashmiri7583
Russian
8285
Uzbek
8590
Czech
6783
Kazakh
7575
Samoan
8377
Vietnamese
8673
Danish
6865
Kirghiz
7589
Sanskrit
8365
Volapük
8679
Dutch
7876
Korean
7579
Scots Gaelic
7168
Welsh
6789
English
6978
Kurdish
7585
Serbian
8382
Wolof
8779
Esperanto
6979
Laothian
7679
Serbo-Croatian
8372
Xhosa
8872
Estonian
6984
Latin
7665
Shona
8378
Yiddish
7473
Faeroese
7079
Latvian, Lettish
7686
Sindhi
8368
Yoruba
8979
43
REFERENCE
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu” (See page
21).
Country Code List
Enter the appropriate code number for the initial setting “Country Code” (See page 23).
Code
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CS
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
44
Country
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaidjan
Bosnia-Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Ivory Coast
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Former Czechoslovakia
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Code
ER
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Country
Eritrea
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia
Faroe Islands
France
France (European
Territory)
Gabon
Great Britain
Grenada
Georgia
French Guyana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe (French)
Equatorial Guinea
Greece
S. Georgia & S. Sandwich
Isls.
Guatemala
Guam (USA)
Guinea Bissau
Guyana
Hong Kong
Heard and McDonald
Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia6
Kiribati
Comoros
Saint Kitts & Nevis Anguilla
North Korea
South Korea
Kuwait
Cayman Islands
Kazakhstan
Laos
Lebanon
Code
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
Country
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libya
Morocco
Monaco
Moldavia
Madagascar
Marshall Islands
Macedonia
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique (French)
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia (French)
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
Polynesia (French)
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn Island
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
Code
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SU
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UK
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Country
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Islands
Slovak Republic
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Saint Tome and Principe
Former USSR
El Salvador
Syria
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tadjikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania
Ukraine
Uganda
United Kingdom
USA Minor Outlying
Islands
United States
Uruguay
Uzbekistan
Vatican City State
Saint Vincent &
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (USA)
Vietnam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
Specifications
General
AC 120V, 60 Hz
50W
430 X 90 X 350 mm (16.9 x 3.5 x 13.8 inches) (w x h x d)
8 kg (17.6 lbs)
5˚C to 35˚C
5 % to 90 %
NTSC
REFERENCE
Power requirements
Power consumption
Dimensions (approx.)
Weight (approx.)
Operating temperature
Operating humidity
Signal system
Inputs
ANTENNA IN
VHS VIDEO IN(LINE1, 2)
VHS AUDIO IN(LINE1, 2)
Antenna or CATV input, 75 ohms
1 Vp-p 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 ohms, RCA jack (L, R) x 2
Outputs
MONITOR OUT
S-VIDEO OUT
Component Video output
1 Vp-p 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 1
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Antenna
VHF output signal
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
75 ohms (VHF/UHF)
Channel 3 or 4
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
200Hz to 8kHz
More than 65 dB (EE mode)
More than 70 dB (EE mode)
More than 45 dB (EE mode)
DVD Specifications
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 20 Hz to 44 kHz, DVD (PCM 48 kHz): 20 Hz to 22 kHz
CD: 20 Hz to 18 kHz
More than 70 dB
Less than 0.5 %
More than 65 dB (DVD/CD)
Tuner section
System
Tuning range
Antenna
PLL quartz-locked digital synthesizer system
87.5 ~ 108.0 MHz (FM)
530 ~ 1720 KHz (AM)
Wire antenna (FM)
Loop antenna (AM)
45
Specifications (Continued)
Speakers
Satellite (LHS-C245T)
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max Input Power
Net Dimensions (W x H x D)
Net Weight
Passive Subwoofer (LHS-C245W)
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max Input Power
Net Dimensions (W x H x D)
Net Weight
Accessories:
1 Way 1 Speaker
6Ω
130 - 20,000 Hz
85 dB/W (1m)
45W
90W
89 x 130 x 114 mm
0.5 kg
1 Way 1 Speaker
8Ω
50 - 1,500 Hz
82 dB/W (1m)
75W
150W
160 x 350 x 333 mm
4.5 kg
Video cable x 1, Audio cable x 1, RF 75-ohm Coaxial Cable x 1, Speaker cable x 5, FM Antenna cable x 1,
AM Antenna cable x 1, Remote control x 1, Batteries (AAA) x 2
Design and specifications are subject to change without prior notice.
46
ZENITH ELECTRONICS CORPORATION
DVD+Hi-Fi VCR Combo Home Theater System XBS448
LIMITED WARRANTY – USA
Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period ("Warranty Period") listed below, effective from the date
("Date of Purchase") of original purchase of the product. This limited warranty is good only to the original purchaser of the product and effective only when used in the United States, excluding U.S. Territories.
WARRANTY PERIOD:
LABOR: 90 days from the Date of Purchase.
PARTS: 1 Year from the Date of Purchase.
* Parts replaced are warranted for the remaining
portion of the original warranty period.
HOW SERVICE IS HANDLED:
Carry-In Service: Please retain dealer’s dated bill of
sale or delivery ticket as evidence of the Date of
Purchase for proof of warranty, and submit a copy of
the bill of sale to the service person at the time
warranty service is provided.
Please call 1-877-9Zenith (1-877-993-6484) to
locate your nearest Zenith Authorized Service
Center.
Or visit our website at
http://www.zenithservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE
EXPRESS WARRANTY PERIOD ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS,
LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives
you specific legal rights and you may also have other rights that vary from state to state.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
• Damage caused in shipping or transit
• Service required as a result of improper installation,
including incorrect or insufficient AC supply (Please
consult the owner’s manual for power supply
requirements)
• Installation or repair of other components in a video
system
• Set-up or adjustment on consumer controls, or
damage caused by improper adjustments
• Damage cause by other system components
• Damage (including cosmetic damage), failure, loss or
personal injury due to misuse, abuse, negligence,
improper maintenance or storage, or to acts of nature
or other causes beyond Zenith’s control (Causes
beyond Zenith’s control include but are not limited to
lightning strike, power surges, power outages, and
water damage)
• Repair or replacement of warranted parts by other than
Zenith Authorized Service Centers
• Units purchased or serviced outside the coverage area
• Product where the original factory serial numbers have
been removed, defaced, or changed in any way
• Product sold and labeled as "as is, where is" or
similar disclaimer
The costs of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
For nearest Authorized Service
Center, Where to buy, Product
Assistance, or Customer Assistance
Call 1-877-9Zenith (1-877-993-6484) (24 Hours a Day, 365 Days a Year)
and select appropriate option from the menu.
Or visit our website at http://www.zenithservice.com
Marketed and Distributed by LG Electronics U.S.A., Inc.
1000 Sylvan Avenue. Englewood Cliffs, NJ.
Zenith Part No. 206-04009
GS# 3834RH0049U
Printed in Indonesia
Issue O
Download PDF
Similar pages