Version 1.0
Published October 2017
Copyright©2017 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Contents
Chapter 1 Introduction
1
1.1 1
Package Contents
1.2 Specifications
2
1.3 Motherboard Layout
5
1.4 7
I/O Panel
Chapter 2 Installation
2.1 Installing Memory Modules (SO-DIMM) 9
10
2.2 Expansion Slot (PCI Express Slot)
12
2.3 Jumpers Setup
13
2.4 Onboard Headers and Connectors
14
Chapter 3 Software and Utilities Operation 18
3.1 18
Installing Drivers
3.2 ASRock Live Update & APP Shop
19
3.2.1 UI Overview
19
3.2.2 Apps
20
3.2.3 BIOS & Drivers
23
3.2.4 Setting
24
Chapter 4 UEFI SETUP UTILITY
25
4.1 25
Introduction
4.1.1 UEFI Menu Bar
25
4.1.2 Navigation Keys
26
4.2 Main Screen
27
4.3 Advanced Screen
28
4.3.1 CPU Configuration
29
4.3.2 Chipset Configuration
30
4.3.3 Storage Configuration
32
4.3.4 Super IO Configuration
33
4.3.5 ACPI Configuration
35
4.3.6 USB Configuration
37
4.4 Tools
38
4.5 Hardware Health Event Monitoring Screen
40
4.6 Security Screen
41
4.7 Boot Screen
42
4.8 Exit Screen
44
J4105B-ITX
J4005B-ITX
Chapter 1 Introduction
Thank you for purchasing ASRock J4105B-ITX / J4005B-ITX motherboard, a
reliable motherboard produced under ASRock’s consistently stringent quality
control. It delivers excellent performance with robust design conforming to
ASRock’s commitment to quality and endurance.
In this manual, Chapter 1 and 2 contains the introduction of the motherboard
and step-by-step installation guides. Chapter 3 contains the operation guide of the
software and utilities. Chapter 4 contains the configuration guide of the BIOS setup.
Because the motherboard specifications and the BIOS software might be updated, the
content of this documentation will be subject to change without notice. In case any
modifications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, please visit our website for specific information about the model
you are using. You may find the latest VGA cards and CPU support list on ASRock’s
website as well. ASRock website http://www.asrock.com.
1.1 Package Contents
ASRock J4105B-ITX / J4005B-ITX Motherboard (Mini-ITX Form Factor)
ASRock J4105B-ITX / J4005B-ITX Quick Installation Guide
ASRock J4105B-ITX / J4005B-ITX Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield
English
•
•
•
•
•
1
1.2 Specifications
Platform
• Mini-ITX Form Factor
• Solid Capacitor design
CPU
• Intel® Quad-Core Processor J4105 (up to 2.5 GHz)
(for J4105B-ITX)
• Intel® Dual-Core Processor J4005 (up to 2.7 GHz)
(for J4005B-ITX)
Memory
English
2
• Dual Channel DDR4 Memory Technology
• 2 x DDR4 SO-DIMM Slots
* 2GB DRAM per module is not supported.
• Supports DDR4 2400/2133 non-ECC, un-buffered memory
• Max. capacity of system memory: 8GB
Expansion
Slot
• 1 x PCI Express 2.0 x16 Slot (PCIE1: x2 mode)
Graphics
• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to
750MHz) (for J4105B-ITX)
• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to
700MHz) (for J4005B-ITX)
• DX12, OpenGL 4.3, OGL ES 3.0, OpenCL 2.0
• HW Acceleration Decode: HEVC (H.265) 8 bit, HEVC
(H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8,
VP9 8bit, VP9 10 bit
• HW Acceleration Encode: HEVC (H.265) 8 bit, HEVC
(H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8,
VP9 8bit
• Dual graphics output: support D-Sub and HDMI ports by
independent display controllers
• Supports HDMI with max. resolution up to 4K x 2K
(4096x2160) @ 30Hz
• Supports D-Sub with max. resolution up to 2048x1536 @
60Hz
• Supports Auto Lip Sync, xvYCC and HBR (High Bit Rate
Audio) with HDMI Port (Compliant HDMI monitor is
required)
J4105B-ITX
J4005B-ITX
• Supports HDCP with HDMI Port
• Supports Full HD 1080p Blu-ray (BD) playback with HDMI
Port
• 7.1 CH HD Audio (Realtek ALC887 Audio Codec)
* To configure 7.1 CH HD Audio, it is required to use an HD
front panel audio module and enable the multi-channel audio
feature through the audio driver.
• Supports Surge Protection
• ELNA Audio Caps
PCIE x1 Gigabit LAN 10/100/1000 Mb/s
Realtek RTL8111H
Supports Wake-On-LAN
Supports Lightning/ESD Protection
Supports Energy Efficient Ethernet 802.3az
Supports PXE
LAN
•
•
•
•
•
•
Rear Panel
I/O
•
•
•
•
•
•
•
•
Storage
• 2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug
Connector
•
•
•
•
•
•
1 x PS/2 Mouse/Keyboard Port
1 x Parallel Port (ECP/EPP Support)
1 x Serial Port: COM1
1 x D-Sub Port
1 x HDMI Port
1 x USB 2.0 Port (Supports ESD Protection)
3 x USB 3.1 Gen1 Ports (Supports ESD Protection)
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
1 x COM Port Header
1 x Chassis Intrusion and Speaker Header
1 x CPU Fan Connector (3-pin)
1 x Chassis Fan Connector (3-pin)
1 x 24 pin ATX Power Connector
1 x Front Panel Audio Connector
English
Audio
3
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD
Protection)
• 1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)
(Supports ESD Protection)
* USB3_1_2 is shared with USB2_3.
AMI UEFI Legal BIOS with GUI support
Supports Plug and Play
ACPI 5.0 compliant wake up events
Supports jumperfree
SMBIOS 3.0 support
BIOS
Feature
•
•
•
•
•
Hardware Monitor
• CPU/Chassis temperature sensing
• CPU/Chassis Fan Tachometer
• CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by
CPU temperature)
• CPU/Chassis Fan multi-speed control
• CASE OPEN detection
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore
OS
• Microsoft® Windows® 10 64-bit
Certifications
• FCC, CE
• ErP/EuP ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com
English
4
J4105B-ITX
J4005B-ITX
1.3 Motherboard Layout
1
PS2
Keyboard/
Mouse
BIOS
ROM
DDR4_A1
VGA1
PARALLEL PORT
COM1
ATXPWR1
RoHS
USB 3.1 Gen1
T: USB1
B: USB2
CPU_FAN1
CMOS
Battery
2
LAN
Front USB 3.0
HDMI1
HDLED RESET
PLED PWRBTN
PANEL1
3
1
SPK_CI1
RJ-45
1
CLRMOS1
5
HD_AUDIO1
1
SATA3_ 2
USB3_1_2
SATA3_1
COM2
1
Super
I/O
1
USB2_3
USB4_5
Center:
FRONT
Top:
LINE IN
Bottom:
MIC IN
6
1
AUDIO
CODEC
1
PCIE1
14
13
12
11 10
9
8
7
English
USB 3.1 Gen1:
USB4
USB 2.0: USB3
4
DDR4_B1
5
No. Description
English
6
1
CPU Fan Connector (CPU_FAN1)
2
ATX Power Connector (ATXPWR1)
3
System Panel Header (PANEL1)
4
Chassis Intrusion and Speaker Header (SPK_CI1)
5
Clear CMOS Jumper (CLRMOS1)
6
Chassis Fan Connector (CHA_FAN1)
7
2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1)
8
COM Port Header (COM2)
9
USB 2.0 Header (USB4_5)
10
USB 3.1 Gen1 Header (USB3_1_2)
11
USB 2.0 Header (USB2_3)
12
SATA3 Connector (SATA3_1)
13
SATA3 Connector (SATA3_2)
14
Front Panel Audio Header (HD_AUDIO1)
J4105B-ITX
J4005B-ITX
1.4 I/O Panel
1
2
12
11
10
9
3
4
5
7
6
8
No. Description
No. Description
1
PS/2 Mouse/Keyboard Port
7
USB 2.0 Port (USB3_3)
2
Parallel Port
8
USB 3.1 Gen1 Port (USB3_4)
3
LAN RJ-45 Port*
9
HDMI Port
4
Line In (Light Blue)**
10
D-Sub Port
5
Front Speaker (Lime)**
11
COM Port
6
Microphone (Pink)**
12
USB 3.1 Gen1 Ports (USB3_1_2)
* There are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
Activity / Link LED
Speed LED
Status
Description
Status
Description
Off
Blinking
On
No Link
Data Activity
Link
Off
Orange
Green
10Mbps connection
100Mbps connection
1Gbps connection
English
LAN Port
7
** To configure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multichannel audio feature through the audio driver.
Please set Speaker Configuration to “7.1 Speaker”in the Realtek HD Audio Manager.
Function of the Audio Ports in 7.1-channel Configuration:
English
8
Port
Function
Light Blue (Rear panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
Rear Speaker Out
Front Speaker Out
Central /Subwoofer Speaker Out
Side Speaker Out
J4105B-ITX
J4005B-ITX
Chapter 2 Installation
This is a Mini-ITX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
English
• Make sure to unplug the power cord before installing or removing the motherboard.
Failure to do so may cause physical injuries to you and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.
9
2.1 Installing Memory Modules (SO-DIMM)
This motherboard provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots, and
supports Dual Channel Memory Technology.
1. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4
slot; otherwise, this motherboard and SO-DIMM may be damaged.
2. The SO-DIMM only fits in one correct orientation. It will cause permanent damage
to the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at
incorrect orientation.
Supported DDR4 Non ECC SODIMM
Raw Card
A (1Rx8)
B (2Rx8)
C (1Rx16)
Dual Channel Memory Configuration
English
10
DDR4_A1
Populated
DDR4_B1
Populated
J4105B-ITX
J4005B-ITX
1
2
English
3
11
2.2 Expansion Slot (PCI Express Slot)
There is 1 PCI Express slot on the motherboard.
Before installing an expansion card, please make sure that the power supply is
switched off or the power cord is unplugged. Please read the documentation of the
expansion card and make necessary hardware settings for the card before you start the
installation.
PCIe slot:
PCIE1 (PCIe 2.0 x16 slot) is used for PCI Express x2 lane width cards.
Warning:
To ensure better graphics compability, the BIOS is set to "boot from Onboard VGA"
as default even the user install a VGA card on PCIe slot.
English
12
J4105B-ITX
J4005B-ITX
2.3 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is
“Open”.
*The jumper cap is not provided.
Clear CMOS Jumper
(CLRMOS1)
(see p.5, No. 5)
Short: Clear CMOS
Open: Default
2-pin Jumper
CLRMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system setup
parameters. There are two ways for you to clear and reset the system parameters
to the default setup. Please turn off the computer and unplug the power cord, then
you may either short the solder points on CLRMOS1 by using metal material,
e.g., a paper clip for 3 seconds; or you may use a jumper cap to short the pin on
CLRMOS1 for 3 seconds. Please remember to remove the paper clip or the jumper
cap after clearing the CMOS.
English
If you clear the CMOS, the case open may be detected. Please adjust the BIOS option
“Clear Status” to clear the record of previous chassis intrusion status.
13
2.4 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.
System Panel Header
(9-pin PANEL1)
(see p.5, No. 3)
GND
GND
RESET#
GND
PWRBTN#
HDLED-
PLEDPLED+
HDLED+
1
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may configure the way to
turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart
the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is on when
the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state.
The LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is on when
the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists
of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make sure the wire
assignments and the pin assignments are matched correctly.
English
Chassis Intrusion and
Speaker Header
(7-pin SPK_CI1)
(see p.5, No. 4)
14
Please connect the
chassis intrusion and the
chassis speaker to this
header.
J4105B-ITX
J4005B-ITX
Serial ATA3 Connectors
(SATA3_1:
see p.5, No. 12)
(SATA3_2:
see p.5, No. 13)
SATA3_2
USB 2.0 Headers
(9-pin USB2_3)
(see p.5, No. 11)
(9-pin USB4_5)
(see p.5, No. 9)
USB_PWR
PP+
1
USB 3.1 Gen1 Header
(19-pin USB3_1_2)
(see p.5, No. 10)
SATA3_1
GND
DUMMY
These two SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
There are two headers
on this motherboard.
Each USB 2.0 header can
support two ports.
GND
P+
PUSB_PWR
IntA_P_D+
IntA_P_DGND
IntA_P_SSTX+
IntA_P_SSTXGND
IntA_P_SSRX+
IntA_P_SSRXVbus
There is one header on
this motherboard. This
USB 3.1 Gen1 header can
support two ports.
1
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.5, No. 14)
GND
PRESENCE#
MIC_RET
OUT_RET
This header is for
connecting audio devices
to the front audio panel.
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
English
ID
Vbus
IntA_P_SSRXIntA_P_SSRX+
GND
IntA_P_SSTXIntA_P_SSTX+
GND
IntA_P_DIntA_P_D+
15
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must
support HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.
Chassis Fan Connector
(3-pin CHA_FAN1)
(see p.5, No. 6)
CPU Fan Connector
(3-pin CPU_FAN1)
(see p.5, No. 1)
ATX Power Connector
(24-pin ATXPWR1)
(see p.5, No. 2)
English
16
GND
+12V
CHA_FAN_SPEED
GND
+12V
CPU_FAN_SPEED
12
24
1
13
Please connect fan cable
to the fan connector and
match the black wire to
the ground pin.
Please connect the CPU
fan cable to the connector
and match the black wire
to the ground pin.
This motherboard provides a 24-pin ATX power
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
13.
J4105B-ITX
J4005B-ITX
Serial Port Header
(9-pin COM2)
(see p.5, No. 8)
RRXD1
DDTR#1
DDSR#1
CCTS#1
This COM2 header
supports a serial port
module.
1
English
RRI#1
RRTS#1
GND
TTXD1
DDCD#1
17
Chapter 3 Software and Utilities Operation
3.1 Installing Drivers
The Support CD that comes with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard’s features.
Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu does not appear automatically, locate and double click on the file
“ASRSETUP.EXE” in the Support CD to display the menu.
Drivers Menu
The drivers compatible to your system will be auto-detected and listed on the
support CD driver page. Please click Install All or follow the order from top to
bottom to install those required drivers. Therefore, the drivers you install can work
properly.
Utilities Menu
The Utilities Menu shows the application software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
English
18
J4105B-ITX
J4005B-ITX
3.2 ASRock Live Update & APP Shop
The ASRock Live Update & APP Shop is an online store for purchasing and
downloading software applications for your ASRock computer. You can quickly and
easily install various apps and support utilities. With ASRock Live Update & APP
Shop, you can optimize your system and keep your motherboard up to date simply
with a few clicks.
Double-click
utility.
on your desktop to access ASRock Live Update & APP Shop
*You need to be connected to the Internet to download apps from the ASRock Live Update & APP Shop.
3.2.1 UI Overview
Category Panel
Hot News
Information Panel
Category Panel: The category panel contains several category tabs or buttons that
when selected the information panel below displays the relative information.
English
Information Panel: The information panel in the center displays data about the
currently selected category and allows users to perform job-related tasks.
Hot News: The hot news section displays the various latest news. Click on the image
to visit the website of the selected news and know more.
19
3.2.2 Apps
When the "Apps" tab is selected, you will see all the available apps on screen for you
to download.
Installing an App
Step 1
Find the app you want to install.
The most recommended app appears on the left side of the screen. The other various
apps are shown on the right. Please scroll up and down to see more apps listed.
You can check the price of the app and whether you have already intalled it or not.
- The red icon displays the price or "Free" if the app is free of charge.
- The green "Installed" icon means the app is installed on your computer.
Step 2
Click on the app icon to see more details about the selected app.
English
20
J4105B-ITX
J4005B-ITX
Step 3
If you want to install the app, click on the red icon
to start downloading.
Step 4
When installation completes, you can find the green "Installed" icon appears on the
upper right corner.
.
English
To uninstall it, simply click on the trash can icon
*The trash icon may not appear for certain apps.
21
Upgrading an App
You can only upgrade the apps you have already installed. When there is an
available new version for your app, you will find the mark of "New Version"
appears below the installed app icon.
Step 1
Click on the app icon to see more details.
Step 2
Click on the yellow icon
English
22
to start upgrading.
J4105B-ITX
J4005B-ITX
3.2.3 BIOS & Drivers
Installing BIOS or Drivers
When the "BIOS & Drivers" tab is selected, you will see a list of recommended or
critical updates for the BIOS or drivers. Please update them all soon.
Step 1
Please check the item information before update. Click on
to see more details.
Step 2
Click to select one or more items you want to update.
Step 3
English
Click Update to start the update process.
23
3.2.4 Setting
In the "Setting" page, you can change the language, select the server location, and
determine if you want to automatically run the ASRock Live Update & APP Shop
on Windows startup.
English
24
J4105B-ITX
J4005B-ITX
Chapter 4 UEFI SETUP UTILITY
4.1 Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your
system. You may run the UEFI SETUP UTILITY by pressing <F2> or <Del> right
after you power on the computer, otherwise, the Power-On-Self-Test (POST) will
continue with its test routines. If you wish to enter the UEFI SETUP UTILITY after
POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the
reset button on the system chassis. You may also restart by turning the system off
and then back on.
Because the UEFI software is constantly being updated, the following UEFI setup
screens and descriptions are for reference purpose only, and they may not exactly
match what you see on your screen.
4.1.1 UEFI Menu Bar
Main
For setting system time/date information
Advanced
For advanced system configurations
Tool
Useful tools
H/W Monitor
Displays current hardware status
Security
For security settings
Boot
For configuring boot settings and boot priority
Exit
Exit the current screen or the UEFI Setup Utility
English
The top of the screen has a menu bar with the following selections:
25
4.1.2 Navigation Keys
Use < > key or < > key to choose among the selections on the menu bar, and
use < > key or < > key to move the cursor up or down to select items, then
press <Enter> to get into the sub screen. You can also use the mouse to click your
required item.
Please check the following table for the descriptions of each navigation key.
Navigation Key(s)
+ / -
To change option for the selected items
<Tab>
Switch to next function
<PGUP>
Go to the previous page
<PGDN>
Go to the next page
<HOME>
Go to the top of the screen
<END>
English
26
Description
Go to the bottom of the screen
<F1>
To display the General Help Screen
<F7>
Discard changes and exit the SETUP UTILITY
<F9>
Load optimal default values for all the settings
<F10>
Save changes and exit the SETUP UTILITY
<F12>
Print screen
<ESC>
Jump to the Exit Screen or exit the current screen
J4105B-ITX
J4005B-ITX
4.2 Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and
display the system overview.
J4105B-ITX:
English
J4005B-ITX:
27
4.3 Advanced Screen
In this section, you may set the configurations for the following items:
CPU Configuration, Chipset Configuration, Storage Configuration, Super IO Configuration, ACPI Configuration and USB Configuration.
Setting wrong values in this section may cause the system to malfunction.
English
28
J4105B-ITX
J4005B-ITX
4.3.1 CPU Configuration
Intel SpeedStep Technology
Intel SpeedStep technology allows processors to switch between multiple
frequencies and voltage points for better power saving and heat dissipation.
CPU C States Support
Enable CPU C States Support for power saving. It is recommended to keep C1 and
C6 all enabled for better power saving.
Enhanced Halt State (C1E)
Enable Enhanced Halt State (C1E) for lower power consumption.
Intel Turbo Boost Technology
Intel Turbo Boost Technology enables the processor to run above its base operating
frequency when the operating system requests the highest performance state.
VT-d
English
Intel® Virtualization Technology for Directed I/O helps your virtual machine
monitor better utilize hardware by improving application compatibility and
reliability, and providing additional levels of manageability, security, isolation, and
I/O performance.
29
4.3.2 Chipset Configuration
DRAM Voltage
Use this to configure DRAM Voltage. The default value is [Auto].
Primary Graphics Adapter
Select a primary VGA.
Share Memory
Configure the size of memory that is allocated to the integrated graphics processor
when the system boots up.
Onboard HD Audio
Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and
automatically disable it when a sound card is installed.
Front Panel
Enable/disable front panel HD audio.
Onboard LAN
English
Enable or disable the onboard network interface controller.
PCIE1 Link Speed
Select the link speed for PCIE1.
30
J4105B-ITX
J4005B-ITX
ASPM
This option enables/disables the ASPM support.
Deep Sleep
Configure deep sleep mode for power saving when the computer is shut down.
Restore on AC/Power Loss
English
Select the power state after a power failure. If [Power Off] is selected, the power will
remain off when the power recovers. If [Power On] is selected, the system will start
to boot up when the power recovers.
31
4.3.3 Storage Configuration
SATA Controller(s)
Enable/disable the SATA controllers.
SATA Mode Selection
AHCI: Supports new features that improve performance.
AHCI (Advanced Host Controller Interface) supports NCQ and other new features
that will improve SATA disk performance.
SATA Aggressive Link Power Management
SATA Aggressive Link Power Management allows SATA devices to enter a low
power state during periods of inactivity to save power. It is only supported by AHCI
mode.
Hard Disk S.M.A.R.T.
English
S.M.A.R.T stands for Self-Monitoring, Analysis, and Reporting Technology. It is a
monitoring system for computer hard disk drives to detect and report on various
indicators of reliability.
32
J4105B-ITX
J4005B-ITX
4.3.4 Super IO Configuration
Serial Port 1
Enable or disable the Serial port 1.
Serial Port Address
Select the address of the Serial port.
Serial Port 2
Enable or disable the Serial port 2.
Serial Port Address
Select the address of the Serial port.
Parallel Port
Enable or disable the Parallel port.
Change Settings
English
Select the address of the Parallel port.
Device Mode
Select the device mode according to your connected device.
33
PS2 Y-Cable
Enable the PS2 Y-Cable or set this option to Auto.
English
34
J4105B-ITX
J4005B-ITX
4.3.5 ACPI Configuration
Suspend to RAM
It is recommended to select auto for ACPI S3 power saving.
ACPI HPET Table
Enable the High Precision Event Timer for better performance and to pass WHQL
tests.
PS/2 Keyboard Power On
Allow the system to be waked up by a PS/2 Keyboard.
PCIE Device Power On
Allow the system to be waked up by a PCIE device and enable wake on LAN.
Ring-In Power On
Allow the system to be waked up by onboard COM port modem Ring-In signals.
RTC Alarm Power On
English
Allow the system to be waked up by the real time clock alarm. Set it to By OS to let
it be handled by your operating system.
35
USB Keyboard/Remote Power On
Allow the system to be waked up by an USB keyboard or remote controller.
USB Mouse Power On
Allow the system to be waked up by an USB mouse.
English
36
J4105B-ITX
J4005B-ITX
4.3.6 USB Configuration
Legacy USB Support
English
Enable Legacy USB Support. AUTO option disables legacy support if no USB
devices are connected. DISABLE option will keep USB devices available only for
EFI applications.
37
4.4 Tools
Instant Flash
Save UEFI files in your USB storage device and run Instant Flash to update your
UEFI.
Internet Flash
ASRock Internet Flash downloads and updates the latest UEFI firmware version
from our servers for you. Please setup network configuration before using Internet
Flash.
*For BIOS backup and recovery purpose, it is recommended to plug in your USB
pen drive before using this function.
English
38
J4105B-ITX
J4005B-ITX
Network Configuration
Use this to configure internet connection settings for Internet Flash.
Internet Setting
Enable or disable sound effects in the setup utility.
UEFI Download Server
English
Select a server to download the UEFI firmware.
39
4.5 Hardware Health Event Monitoring Screen
This section allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, fan
speed and voltage.
CPU Fan 1 Setting
This allows you to set CPU fan 1’s speed. Configuration options: [Full On] and
[Automatic Mode]. The default value is [Full On].
Chassis Fan 1 Setting
This allows you to set chassis fan 1’s speed. Configuration options: [Full On],
[Automatic Mode] and [Manual]. The default value is [Full On].
Case Open Feature
Enable or disable Case Open Feature to detect whether the chassis cover has been
removed.
English
40
J4105B-ITX
J4005B-ITX
4.6 Security Screen
In this section you may set or change the supervisor/user password for the system.
You may also clear the user password.
Supervisor Password
Set or change the password for the administrator account. Only the administrator
has authority to change the settings in the UEFI Setup Utility. Leave it blank and
press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to change the
settings in the UEFI Setup Utility. Leave it blank and press enter to remove the
password.
Secure Boot
Enable to support Secure Boot.
Intel(R) Platform Trust Technology
English
Enable/disable Intel PTT in ME. Disable this option to use discrete TPM Module.
41
4.7 Boot Screen
This section displays the available devices on your system for you to configure the
boot settings and the boot priority.
Fast Boot
Fast Boot minimizes your computer's boot time. In fast mode you may not boot
from an USB storage device. The VBIOS must support UEFI GOP if you are using
an external graphics card. Please notice that Ultra Fast mode will boot so fast that
the only way to enter this UEFI Setup Utility is to Clear CMOS or run the Restart to
UEFI utility in Windows.
Boot From Onboard LAN
Allow the system to be waked up by the onboard LAN.
Setup Prompt Timeout
Configure the number of seconds to wait for the setup hot key.
Bootup Num-Lock
Select whether Num Lock should be turned on or off when the system boots up.
English
Boot Beep
Select whether the Boot Beep should be turned on or off when the system boots up. Please
note that a buzzer is needed.
42
J4105B-ITX
J4005B-ITX
Full Screen Logo
Enable to display the boot logo or disable to show normal POST messages.
Boot Failure Guard Message
English
If the computer fails to boot for a number of times the system automatically restores
the default settings.
43
4.8 Exit Screen
Save Changes and Exit
When you select this option the following message, “Save configuration changes
and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP
UTILITY.
Discard Changes and Exit
When you select this option the following message, “Discard changes and exit
setup?” will pop out. Select [OK] to exit the UEFI SETUP UTILITY without saving
any changes.
Discard Changes
When you select this option the following message, “Discard changes?” will pop
out. Select [OK] to discard all changes.
Load UEFI Defaults
Load UEFI default values for all options. The F9 key can be used for this operation.
Launch EFI Shell from filesystem device
English
Copy shellx64.efi to the root directory to launch EFI Shell.
44
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at https://event.asrock.com/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.
Bijsterhuizen 11-11
6546 AR Nijmegen
The Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.
13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name:
Address:
Phone/Fax No:
ASRock Incorporation
13848 Magnolia Ave, Chino, CA91710
+1-909-590-8308/+1-909-590-1026
hereby declares that the product
Product Name : Motherboard
Model Number : J4105B-ITX / J4005B-ITX
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Representative Person’s Name:
James
Signature :
Date : May 12, 2017
EU Declaration of Conformity
For the following equipment:
Motherboard
(Product Name)
J4105B-ITX / J4005B-ITX / ASRock
(Model Designation / Trade Name)
ASRock Incorporation
(Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.)
(Manufacturer Address)
‫ ڛ‬EMC —Directive 2014/30/EU (from April 20th, 2016)
☐ EN 55022:2010/AC:2011 Class B
‫ ڛ‬EN 55024:2010/A1:2015
‫ ڛ‬EN 55032:2012+AC:2013 Class B
‫ ڛ‬EN 61000-3-3:2013
‫ ڛ‬EN 61000-3-2:2014
☐ LVD —Directive 2014/35/EU (from April 20th, 2016)
☐ EN 60950-1 : 2011+ A2: 2013
☐ EN 60950-1 : 2006/A12: 2011
‫ ڛ‬RoHS — Directive 2011/65/EU
‫ ڛ‬CE marking
(EU conformity marking)
ASRock EUROPE B.V.
(Company Name)
Bijsterhuizen 1111 6546 AR Nijmegen The Netherlands
(Company Address)
Person responsible for making this declaration:
(Name, Surname)
A.V.P
(Position / Title)
December 29, 2017
(Date)
P/N: 15G062066000AK V1.0
Download PDF
Similar pages