Operating Instructions Vented dryer T 7634

Operating Instructions
Vented dryer
T 7634
To avoid the risk of personal injury or
damage to the appliance, it is
essential that you read these
operating instructions before
installation and use. This maschine
is not approved for use in the
United States.
en - CA
M.-Nr. 09 174 580
Caring for the environment
Disposal of packing material
Saving energy
The packing materials protect the dryer
from damage during transport. They
have been selected for environmental
compatibility and efficient disposal and
can therefore be recycled.
To avoid unnecessarily long drying
times and increased energy use:
To prevent suffocation, ensure that any
plastic wrappings, bags, etc. are
disposed of safely and kept out of the
reach of children.
Disposing of your old
appliance
– Let the wash spin in the washer at
maximum spin speed.
You can save about 30% in energy
and time if you spin at 1600 instead
of 800 rpm.
– Use the maximum load for each
drying program. This gives the
optimum energy consumption in
relation to the total amount of
laundry.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
– Ensure that the room where the dryer
is located is sufficiently ventilated.
Ensure that a discarded dryer presents
no danger to children. When being
stored for disposal remove the door to
the drying compartment.
– Inspect the vent ducting regularly
and its components for possible
stoppage by lint and remove as
necessary.
– Clean the lint screen after every use.
– When installing, the vent ducting
avoid too many curves or bends.
2
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Drying tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Proper drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Options/Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gentle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Program Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing the program sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Switching over from a running program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
- Canceling and selecting a new program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
- Interrupting a program and removing laundry . . . . . . . . . . . . . . . . . . . . . . . . 19
Loading or removing laundry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Time remaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electronic lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning door lint filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning port-hole grilles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
What to do, if . . . ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Test and fault messages.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Other faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Replacing the light bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Customer service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Program updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Warranty conditions and warranty period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3
Contents
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Carrying the dryer to the installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Leveling the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ventilating the installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing the dryer vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Calculating total duct length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Rear or side exhaust connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
a Flexible metal duct hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
b Dryer vent systems from metal piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
c Connecting directly to a wall vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
d Vent collector duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Washer-dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Extending the range of drying levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjusting buzzer volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Set memory function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Extending cooldown time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Change function of Filter/Vent indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adjust keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Changing water conductivity setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4
IMPORTANT SAFETY INSTRUCTIONS
,This machine T 7634 meets all
CSA requirements. This machine is
not approved for use in the United
States.
,WARNING - To reduce the risk of
~ Before this appliance is removed for
service or discarded, remove the door
to the drying compartment.
~ Do not reach into the dryer if the
drum is moving.
~ Do not install or store this appliance
where it will be exposed to the weather.
fire, electric shock, or injury to
persons when using your appliance,
follow basic precautions, including
the following:
~ Do not tamper with the controls.
~ Do not repair or replace any part of
~ It is essential to read all instructions
before using the appliance.
~ Do not use fabric softener sheets to
~ The dryer is designed for household
use only and only for drying textiles that
have been washed in water and whose
fabric care label states that they can be
tumble dried. Other uses may be
dangerous. Miele will not be held liable
for damage caused by improper use or
incorrect operation.
~ To prevent the risk of fire, the
~ Do not allow children to play on or in
the appliance. Close supervision is
necessary when the appliance is used
near children. Always close the door
after use to prevent child hazards.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been shown how to use it by a person
responsible for their safety.
the appliance or attempt any servicing
unless specifically recommended in
these operating instructions. Repairs to
electrical appliances should only be
performed by qualified personnel.
Incorrectly repaired machines may
pose a considerable risk to the user.
eliminate static in this dryer. Best
results are achieved when a liquid
softener is used in the washer. Follow
the manufacturers instructions.
following textiles must not be dried in
this dryer:
– items which have not been washed.
– items, such as work-wear, exposed
to grease, oils, or other deposits
(such as lotions or cosmetics) in your
dryer. If these items have not been
thoroughly cleaned there is a danger
that they may contribute to a
chemical reaction that could cause
the laundry to ignite when heated
even after being removed from the
dryer.
5
IMPORTANT SAFETY INSTRUCTIONS
– items that have been previously
cleaned, washed, soaked or spotted
with gasoline, dry-cleaning solvents
or other flammable or explosive
substances. They may give off
vapors that could ignite or explode.
– items treated with flammable
cleaning agents or items containing
acetone, alcohol, gasoline, stain
remover, wax or chemicals from
buffing, etc.
– items which have been splashed with
hair spray, nail polish remover, etc.
When washing heavily soiled items
ensure that sufficient detergent is
used with a high temperature. If in
doubt wash the item several times.
– items containing foam rubber or
similarly textured rubber-like
materials.
– items with padding or filling (e.g.
pillows or jackets) which have been
damaged. Loose filling could catch
fire.
~ WARNING – Never stop a tumble
dryer before the end of the drying cycle
unless all items are quickly removed
and spread out so that the heat is
dissipated.
~ Allow the dryer to complete each
stage of the program selected,
including the cooling down phase. This
will ensure that the items being
removed are not too hot to handle
~ Clean the lint filter before or after
each load.
~ Keep the area around the air intake
(toe kick) and adjacent surrounding
areas free from lint, dust and dirt.
~ The interior of the machine should
be cleaned periodically by qualified
personnel.
This dryer is intended for
residential use only!
~ GROUNDING INSTRUCTIONS
This appliance must be grounded. In
the event of malfunction or breakdown,
grounding will reduce the risk of
electric shock by providing a path of
least resistance for electric current.
This appliance is equipped with a cord
having an equipment grounding
conductor and a grounding plug. The
plug must be plugged into an
appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
~ WARNING – Improper connection of
the equipment-grounding conductor
can result in a risk of electric shock.
Contact a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
~ Do not modify the plug provided
with the appliance: if it will not fit the
outlet, have a proper outlet installed by
a qualified electrician.
~ A faulty power cord must be
replaced by a genuine Miele power
cord.
~ Do not use the dryer without a lint
screen or with a damaged lint screen.
~ Lint screens must be cleaned
regularly!
6
IMPORTANT SAFETY INSTRUCTIONS
~ The dryer should not be operated
without a vent duct.
~ It should not be connected to a
chimney used for other purposes.
~ Do not place the dryer in a room
where there is a risk of frost occurring.
Temperatures around freezing affect
dryer performance.
Acceptable room temperature should
lie between +2°C and +35°C.
~ Check all components of the venting
system (such as the wall pipe, external
grill, elbows and bends, etc.) for
airtightness. Lint can build up,
impeding airflow.
If a pre-existing system is present, it
should be checked before the dryer is
installed.
~ Ducting must not be connected to a
fireplace or gas flue that is in use, nor
to ducting which ventilates rooms with
fireplaces. Otherwise there is the
danger of smoke or exhaust gas being
driven back.
~ A suffocation and poisoning
hazard exists from suction of exhaust
gases, when gas water heaters, space
heaters, coal stoves with chimney
connections, etc., are installed in the
same room, or in the dwelling, or in
neighboring rooms and the under
pressure is 4 Pa or more.
Prevent underpressure by sufficient
room ventilation, by, for instance:
– unclosable ventilation openings in
the external wall, or
Safe operation and avoidance of an
underpressure of 4 Pa or more should
in any case be confirmed by your
Master Chimney Sweep.
~ Keep the room in which the dryer is
installed free of dust and fluff.
Dirt particles in the entering air promote
stoppages.
~ Do not support yourself or lean on
the door. The dryer might tip over.
~ Close the door after every drying
cycle. In this way you can prevent
– children from trying to climb into the
dryer or leaving objects inside it.
– small animals from getting into the
dryer.
~ Do not hose down the dryer.
Accessories
~ Accessory parts may only be
attached or installed when they have
been expressly approved by Miele.
If other parts are added or installed,
guarantee, performance and/or product
liability claims are invalidated.
The manufacturer will not be held
liable for damage caused by failure
to comply with the safety instructions
and warnings.
SAVE THESE INSTRUCTIONS
– a window switch:
the dryer can only be switched on
with the window open.
7
Operating the dryer
Control panel
a Display
b Delay button
This button has a dual function:
- Selecting the duration of the
Timed cold and Timed warm
programs.
- Pre-selection of start time.
c Buzzer button
The end of the program is signaled
audibly.
d Fault indicator / Optical interface
Description: See "Problem solving /
Customer service" section.
e Start/Stop button
Starts and stops a program.
Interrupts a program when pressed.
Flashes during program selection
and lights once the program starts.
8
f Gentle button
Delicate fabrics are dried at a lower
temperature.
g Dryness button
Indicator lights identify the drying
level selected.
h Program selector
Indicator lights identify the program
selected.
i Door button
This button opens the door
independently of the power supply.
j I-On/0-Off jk button
For switching the dryer on and off.
Operating the dryer
Display
The following functions are selected
from the display:
– Delay
– Selecting duration of timed
programs.
– Programmable functions.
The display also shows:
– Program duration.
– Program stage:
Drying
Cooling down
End.
– Test and fault messages.
Program duration/ Estimated time
remaining
When a program is selected, the
estimated time remaining will be
displayed. This is to be considered as
an estimate only.
In this way, the delicate and smoothing
programs can end earlier, when a
certain temperature is reached. This
can happen with particularly fine
fabrics, very small loads, or if items
have previously been dried.
Delay
The delay time selected will be
displayed.
The delay time countdown begins after
pressing the Start button.
Once the time delay expired, the
estimated program duration will appear
in the display and the drying begins.
Programmable functions
The programmable functions can be
used to adapt the dryer to your
personal requirements. In programming
mode, the display will show the function
selected.
The following factors can lead to
variations in the time remaining
estimate: Residual moisture after
spinning; type of fabric; size of load;
ambient temperature, or fluctuations in
the power supply.
The adaptive electronics constantly
adjusts to the individual wash load to
ensure a more accurate estimate of
time remaining. This estimate is
permanently monitored during drying,
which in some cases can lead to a
change in the estimate.
9
Laundry care
Care symbols
Drying
q
Normal/higher temperature
r
reduced temperature: select
Gentle
(for delicate fabrics)
s
Not suitable for dryer
Ironing and rotary ironing
I
very hot
H
hot
G
not very hot
J
Do not iron/rotary iron
Drying tips
– Always check the weight
recommendation for maximum loads
as listed in the "Program Overview"
section.
Overloading will cause wear and
tear on the laundry, give a poor
drying result and cause more
creasing.
– Do not dry fabrics that are still
soaking wet! After washing, spin
fabrics for at least 30 seconds.
– Dry mixed loads of cottons, colors
and easy-care fabrics in the in the
Mixed program.
– Open jackets so that they dry evenly.
– Woolens and wool blends tend to
mat and shrink. Only handle these
fabrics in the Woolens program.
– The linings of down-filled garments,
depending on quality, tend to shrink.
Handle these fabrics only in the
Smoothing program.
– Pure linens are dried only when
indicated on the care label.
Otherwise the fabric may become
rough. Handle these fabrics only in
the Smoothing program.
– Cottons (such as T-shirts and
underwear) depending on quality,
often shrink at the first wash.
Therefore: to avoid further shrinkage,
do not over-dry these textiles.
– Starched laundry may be dried. To
achieve the usual finish, however,
use a double amount of starch.
– Wash new colored fabrics separately
before the first drying. Do not dry
them together with light-colored
fabrics since their colors may run
and discolor other garments or even
plastic dryer components.
10
Laundry care
– Wrinkling increases with larger loads.
This especially occurs with very fine
fabrics as used in shirts and blouses.
To limit wrinkling the dryer performs the
following actions:
1. Tumble drying with drum reversal
(prevents roll-ups of laundry,
creasing and uneven drying),
2. Constantly measures the
temperature of air coming into and
leaving the drum,
3. Cycles two heater sections for 0, half
and full power,
4. Automatic drying stage termination,
after the desired Dryness level of
laundry is reached. To do this, the
dryer is equipped with systems:
- water conductivity metering,
- sensing of laundry’s residual
moisture,
- software.
5. Cooling down with tumbling and
drum reversal,
6. Anti-crease with drum reversal.
In cases of doubt, reduce the load by
dividing it.
Use the Dress shirts program.
11
Proper drying
Brief instructions
The operating steps identified with
numbers(A, B, C, ...) may be used as
short-cut instructions.
A Preparing the laundry
Loosen the washed garments and sort
them by: . .
. . . desired drying level,
. . . type of fabric and finish,
. . . size,
. . . same residual moisture content
after spinning.
This will produce very even drying.
Do not exceed maximum loads
specified in the "Program Overview"
Section.
Overloading may cause wear and
tear on the laundry and adversely
affects drying.
^ Before closing the door, check that
the lint filter is properly inserted in the
door casing.
,Remove foreign objects like
detergent dispensing devices from
the laundry. They can melt and
damage the dryer and the wash.
– Check hems and seams to ensure
that linings don't come out.
– Close duvet covers and pillowcases
to prevent small items from getting
inside.
– Fasten hooks and close buttons.
– Tie fabric belts together.
B Turn on the dryer
You may also switch the dryer on after
loading it, as the drum will not be
illuminated, to save energy.
^ To turn it on, press the I-On/0-Offjk
button.
C Loading the dryer
^ Press the Door button to open.
^ Place the laundry loosely in the drum.
12
Ensure that no small items are
jammed in the door, because they
might otherwise be damaged.
Proper drying
D Select program
Woolens and Smoothing programs:
– cannot be altered.
Timed program
The Delay button flashes when Timed
cold or Timed warm programs are
selected.
^ Repeatedly press the Delay button
until the required duration appears in
the display.
^ Select the desired program.
The indicator light for the program
selected lights up.
Other indicator lights for drying levels
or extras may be lit, and drying times
displayed.
Dryness level selection in programs:
– Normal, Wrinkle-free, Delicates,
Mixed, Dress shirts, Denim/Jeans
Drying time can be selected in
10-minute increments from 20 minutes
up to 2 hours.
E Extra options/Select Delay
^ Press button to select the following
options:
Gentle, Buzzer, Delay options (see
"Options/Delay").
Anti-Crease action always activates
at program's end (see next page).
Please note: Delay is not possible in
combination with the Timed warm and
Timed cold programs.
^ Press the button repeatedly until the
desired indicator light is lit.
For Normal any dryness level can be
selected, but selection is limited in
other programs.
Note: The estimate of time remaining
shown in the display varies with each
new program selection.
13
Proper drying
F Starting the program
G End of program - Remove laundry
The Start/Stop button flashes during
program selection. This means that a
program can be started.
0 and End appear in the display to
indicate the program end. The buzzer
sounds at intervals (when selected).
^ Press the Start/Stop button.
Drying appears in the display and the
time remaining is counted down.
After the program end the drum rotates
reversible in intervals if clothes are not
removed (Anti-crease action). This
helps to prevent creasing for up to 2
hours.
Before the end of a program
^ Press the Door button.
After the drying phase finished a
cooldown phase follows.
The following programs have no
cooldown phase: Woolens, Smoothing.
^ Open the door.
The Start/Stop button lights.
^ Remove the laundry.
Check that the drum is empty.
Laundry left behind may be
damaged if dried again.
To save energy, the drum light turns off
after a few minutes when the dryer is
not operating and the door is open.
^ To shut it off, press the jk button.
^ Clean the lint filter.
^ Close the door.
14
Options/Delay
Gentle
Starting
Delicate fabrics (with the rsymbol on
the care label, such as acrylics) must
be dried at lower temperatures for
longer durations.
^ Press the Start/Stop button.
On some programs Gentle is
permanently set and cannot be
deselected.
Buzzer
At the end of the program a buzzer
sounds at intervals, for a maximum of
1 hour.
A continuous warning tone for fault
messages sounds whether the buzzer
is on or off.
Delay
With the Delay option, you can select a
later program start time. Program start
can be delayed by 30 minutes up to a
maximum of 24 hours. This enables
you, for instance, to take advantage of
night electricity rates.
– The Delay indicator light comes on.
The Delay counts down to program
start as follows:
– More than I0^, in whole hours.
– Less than I0^, in minutes.
The drum will turn briefly every hour to
prevent creasing.
Canceling / altering Delay
^ Press the Start/Stop button.
The Delay is cancelled.
^ Repeatedly press the Delay button
until the required duration appears in
the display.
^ Press the Start/Stop button.
The Delay resumes from the beginning.
Adding laundry
You can add laundry while the Delay is
still counting down:
After program selection:
^ Switch off the dryer.
^ Repeatedly press the Delay button
until the required duration appears in
the display.
^ Open the door and add the laundry.
^ Close the door and switch on the
dryer.
– The Delay indicator light flashes.
– Times of
up to I0^ are selected in 30-minute
steps,
more than I0^ in one-hour steps.
– If you keep the Delay button pressed
in, the time will continue to increase
up to 24^.
15
Program Overview
Normal
Extra dry, Normal
Fabrics
Single- and multi-layered cotton such as: hand towels, T-shirts, baby
clothes.
Note
– Select Extra dry for multi-layered and extra thick fabrics.
– Do not use Extra dry to dry jersey fabrics like T-shirts and baby
clothes - they may shrink.
Gentle
To be selected for delicate fabrics with the care symbol r.
Hand iron, Rotary iron
Fabrics
Cotton or linen fabrics. For example: Table linens, bed linens,
starched laundry.
Note
– You can keep laundry moist if you roll it up until ready to iron it.
Gentle
To be selected for delicate fabrics with the care symbol r.
Wrinkle-free
Extra dry, Normal, Hand iron
Fabrics
Easy-care fabrics in synthetics, cotton or blends. For example:
sweaters, dresses, trousers, skirts, tablecloths.
Note
– To reduce creasing even more, select Hand iron and reduce the
load to 1.5 kg*.
– Fabrics are dried with low creasing with the Hand iron drying
program, depending on fabric type and load.
Gentle
To be selected for delicate fabrics with the care symbol r.
Delicates
Normal, Hand iron
Fabrics
Delicate items made of synthetic fibres, blends or cottons such as
shirts, blouses, lingerie, appliqué fabrics.
Gentle
Unavailable.
16
Program Overview
Woolens
Fabrics
Woolens.
Note
– Remove items immediately after the end of the program while still
slightly damp. Allow items to air dry.
Gentle
Unavailable.
Smoothing
Fabrics
– Cotton or linen fabrics.
– Synthetics, cotton or blends. For example: cotton trousers, jackets,
shirts.
Note
– Program to reduce creases formed during spin cycle in washer.
– Remove garments immediately the program ends and air-dry
Gentle
Unavailable.
Mixed
Normal, Hand iron
Fabrics
Mixed loads of fabrics for the Normal and Wrinkle-free programs.
Dress shirts
Normal, Hand iron
Fabrics
Shirts and blouses.
Gentle
To be selected for delicate fabrics with the care symbol r.
Denim / Jeans
Normal, Hand iron
Fabrics
Denim material like trousers, jackets, skirts or shirts.
Gentle
To be selected for delicate fabrics with the care symbol r.
17
Program Overview
Timed cold
Fabrics
– Any fabric needing airing.
Timed warm
Fabrics
– Additional drying of multi-layered garments which dry unevenly
owing to their design: e.g., jackets, pillows and voluminous fabrics.
– Drying individual laundry items: e.g. bath towels, bathing suits, dish
cloths.
Note
To start with, do not select the longest time. Determine the most
suitable time by trial.
Tip:
Use Timed warm to remove or reduce unwanted odors from clean
cotton clothing (duration: 1/2-1 hour). The freshening effect is
reinforced if you moisten the clothing or use a sheet of fabric
conditioner before airing them. Odor reduction will be less for
synthetics.
Gentle
To be selected for delicate fabrics with the care symbol r.
18
Changing the program sequence
Switching over from a running
program
As a protection against unintentional
changes, program selection is no
longer possible.
To be able to choose a new program,
you must cancel the current program.
- Canceling and selecting a new
program
^ Press the Start/Stop button.
The load will be cooled down for a
few minutes, until a specific drying
time and temperature have been
reached.
If you press the Start/Stop button
again, the drum stops, End appears
in the display.
^ Switch the dryer off.
Loading or removing laundry
^ Press the Door button.
^ Open the door.
,Danger of burning:
Do not touch the back of the drum
when adding or removing items.
Temperatures in the drum area can
be high.
^ Add or remove laundry as needed.
^ Close the door.
^ Press the Start/Stop button.
Time remaining
When the program sequence is
changed, the time remaining as shown
by the display may differ from the
actual drying time.
^ Then, switch it on again.
^ Select and start a new program immediately.
- Interrupting a program and
removing laundry
^ See below: "Loading or removing
laundry".
^ Turn the dryer off after closing the
door.
19
Electronic lock
The lock function protects your dryer
against unauthorized use.
You can activate this function whenever
you wish.
It locks the dryer's electronics. It can be
turned on, but no program can be
started.
– In such a case, the Gentle indicator
light flashes and a key symbol 0-§
appears in the display.
The door may be opened at any time,
as it is not locked.
Activating the lock
Precondition:
– The dryer is switched off.
– The door is closed.
A Press the Gentle button and keep it
pressed until Step E.
B Press the I-On/0-Off jk button in.
The Mixed indicator light comes on.
C Slowly turn the program selector
step by step through three positions
clockwise.
The three program indicator lights
must light up in succession.
20
C Slowly turn the program selector
step by step through three positions
counterclockwise.
The three program indicator lights
must light up in succession.
TheGentle indicator light flashes and
the key symbol 0-§ appears in the
display.
E Release the Gentle button.
The lock function has been activated.
^ You may turn off the dryer.
Deactivating the lock
Precondition:
– The dryer is switched off.
– The door is closed.
^ The procedure is as for "Activating
the Lock". Perform steps A toE.
At step E the indicator light for the
Gentle button no longer flashes and the
0-§ key symbol goes out.
The lock function has been
deactivated.
Cleaning and care
Cleaning door lint filter
The lint screen in the door casing
collects lint generated by the drying
process. Clean it after every drying*.
* Also check the lint screen when
the Filter/Vent indicator light comes
on.
Cleaning the lint screen without
water
Tip: You can dispose of the lint without
touching it by using a vacuum cleaner.
^ Rub or vacuum the lint from the
screen surface.
^ Remove the lint from the space in the
door casing with a bottle brush or the
vacuum.
^ Wipe the door casing seal (2) all
around with a damp cloth.
^ Insert the lint screen fully into the
door casing and close the door.
Cleaning the lint screen with water
^ Pull the lint screen (1) out of the door
casing.
The lint screen should be given a
wet cleaning only when it is
severely blocked or plugged.
^ Clean the lint screen under running
hot water.
^ Dry it thoroughly with care.
21
Cleaning and care
Cleaning port-hole grilles
Periodically clean the screens in the
door opening as well as the air
passage underneath the screens.
Cleaning the dryer
Disconnect the dryer from the
electrical supply.
^ Clean the housing, control panel and
door seal only with a slightly damp
cloth and mild detergent or soapy
water.
^ Clean stainless steel parts (like the
drum) with a suitable stainless steel
cleaner.
Use no scouring products, cleaners
containing solvents, or glass or
all-purpose cleaners. They can
damage plastic surfaces and other
parts.
^ Turn the left and right screen knobs
a (until you hear them click).
^ Grasping the knobs, pull the lint
screens out towards the center b.
^ Clean the screens under running hot
water and dry them.
^ Also clean the air passages
underneath the screens, using a
vacuum cleaner, for example.
^ Insert the bottom of the screens and
press the screens upwards.
^ Latch both knobs (until you hear
them click).
22
^ Dry all parts with a soft cloth.
Trouble shooting
What to do, if . . . ?
You can remedy most problems yourself. In many cases you can save time and
expense, since you will not have to call in customer service.
The following tips should help you locate and remedy the cause of a problem.
Please note the following:
,Repairs to electrical appliances should only be carried out by qualified
professionals. Work performed by unqualified persons can place the user at
considerable risk.
Test and fault messages.
Problem
Cause
Solution
Cancelling a program
0 and End appear in
the display
The buzzer sounds.
This is not a fault.
The electronics recognizes
that there is no laundry in
the drum and cancels the
program.
Drying of single or already
dried laundry items can
also lead to program
cancellation.
In future, dry individual
laundry items with the
Timed warm program.
Cancelling test message:
– Open and close door
0-§ appears in the
display.
Gentle indicator light
flashes.
The lock function has been If you wish to dry, you must
activated.
disable the lock function
(see "Electronic lock
function").
Cancelling a program
The buzzer sounds.
Flashing display may
show Cold air or End.
The cause is not immediately obvious.
– Switch the dryer off and
then on again.
– Start a program.
If program interruption and
error message occur, a
fault is present. Contact
Miele customer service.
23
Trouble shooting
Problem
Cause
Filter/Vent indicator The indicator light shows
light goes on.
that the dryer is not
operating at its most
efficient or economical.
Possible causes: Blockage
by lint or detergent
residues.
The dryer vent duct may be
too long, which is not a
dryer fault.
Cancelling a
Possible causes and
program
remedies are described
Filter/Vent indicator above.
light goes on.
The buzzer sounds.
24
Solution
– As a rule, it is sufficient to
clean the lint screens.
Should that not be
sufficient, then check all
possible causes listed
under "The drying cycle
goes on too long or even
switches off."
Cancelling test message:
– Open and close door
– Pay attention to length
and diameter when
making duct calculation.
See "Installing the vent
duct".
– Too long a vent duct will
result in longer program
times and higher energy
consumption.
You can deactivate the
Filter/Vent indicator lights
(see section on
"Programmable functions").
Cancelling the fault
message:
– Open and close door
– Start a program.
– If the fault message
comes back, call
Customer Service.
Trouble shooting
Other faults
Problem
The drying
process goes on
too long or even
switches off.
Even after the lint
screen is cleaned,
the Filter/Vent
indicator come
on.
Cause
Solution
Please check all possible causes and switch the dryer
off and then on again.
Insufficient ventilation,
Open a door or window and
perhaps because the
let in increased air flow.
installation space is too
small.
The door lint filter is blocked Remove the lint.
with lint.
The vent ducting or its outlet
is blocked with lint.
– Check all components of
the venting (such as the
wall pipe, external grill,
elbows and bends, etc.)
for unimpeded air flow.
– Remove the lint.
Clothes were insufficiently
spin-dried.
In future, spin textiles in the
washer at a higher rpm.
The dryer is overloaded.
The laundry was
not satisfactorily
dried.
Verify the maximum load for
each drying program.
– In future, open the zippers.
Metal components such as
zippers have prevented the
If the problem recurs, in
moisture level of the laundry future dry garments with long
from being determined
zippers using the Timed
accurately.
warm program.
The load consisted of various – Re-dry with Timed warm.
fabrics.
– Next time, select a suitable
program.
25
Trouble shooting
Problem
Cause
Synthetic-fiber laundry
items are statically
charged after drying.
Synthetics have a
tendency to static
discharges.
There has been a lint
buildup.
26
Solution
Using a fabric softener in
the last rinse cycle can
reduce static charge
when drying.
Drying releases fabric lint Lint released is captured
in the door lint filter and
formed primarily from
rubbing during wear but can be easily removed
also, in part, from
(see "Care and
Cleaning").
washing. The stress on
fabrics in the dryer is
minimal in relation to their
strength.
Trouble shooting
Problem
Cause
Solution
The Dress shirts,
The cause is not imme- – Switch the dryer off and
Denim/Jeans, and Timed diately obvious.
then on again.
cold programs will not
– Select one of the
start and the indicator
programs.
lights for these programs
– If the program will still
do not come on.
not start, there is a fault.
Contact Miele customer
service.
– Meanwhile, use another
program.
The dryer will not start
when switched on.
Drum lighting does not
come on.
The cause is not imme- – Is the dryer switched
diately obvious.
on?
– Is it plugged in?
– Is the door closed?
– Check fuses or circuit
breakers.
The lighting switches off Switch the dryer off and on
automatically to save
again.
energy.
The bulb may need
You can replace the bulb:
changing.
See the end of this section.
27
Trouble shooting
Replacing the light bulb
Disconnect the dryer from the
electrical supply.
The bulb should be of the same type
and maximum wattage indicated on
the data plate and the lighting cover.
^ Open the door.
^ Replace the bulb.
The hinged cover for the lighting is over
the port-hole.
^ Fold the cover upwards and press it
on the right and left until you hear it
latch.
,Ensure that the cover is properly
seated. If moisture gets inside it may
cause a short-circuit.
^ Gently insert an ordinary tool* under
the side of the cover.
* such as a wide slot-type screwdriver
^ Open the cover by pressing lightly
while rotating your wrist.
The cover opens downwards.
The heat-resistant bulb should be
obtained only from Miele customer service.
28
Customer service
Repairs
Program updates
For faults you cannot correct yourself,
please contact:
The PC optical interface is used by
Miele customer service to transfer
program updates (PC = Program
Correction) as well as for diagnose and
testing.
– the Miele Factory Repair Service.
The telephone number for the
Factory Repair Service is listed at
the back of these operating
instructions.
When contacting the Miele Service
Department, you will need to quote the
model and serial number of your
appliance.
These can be found on the data plate,
visible when the door is open.
In this way, future developments in
fabrics and in the drying procedure can
be integrated into your appliance.
Miele will give timely notification of Program updates.
Warranty conditions and
warranty period
Warranty information can be found in
your warranty booklet.
Optional accessories
Optional accessories for this dryer are
available from Miele customer service.
29
Installation and connection
Front view
a Venting connection: The dryer vent
duct can be connected to the rear of
the machine (as supplied) or on
either the right or left side.
b Power cord
c Control panel
d Door
30
e Four height-adjustable screw feet
Installation and connection
Rear view
Installation site
This dryer can be accommodated
under a worktop if there is sufficient
height.
,Do not install the dryer in a
location where its door could conflict
with room doors.
,The appliance top is not
removable.
Carrying the dryer to the installation
site
a Handgrips under the cover overhang
for moving the appliance (arrows)
b Power cord
c Rear venting connection
The rear cover overhang provides
handgrips for transport. To carry the
dryer from its shipping base to the
installation site, use the front feet of
the appliance and the rear top
overhang.
Washer-dryer stack
The dryer can be combined with a
Miele automatic washer in a
washer-dryer stack. For this, a "WTV
412" stacking unit* is required.
* Miele accessory available on order
,Installation of the stacking unit
may be performed only by an
authorized Miele technician.
31
Installation and connection
Leveling the dryer
,Ensure there is an air gap of at
least 10 mm between the underside
of the dryer and the floor. This air
gap must not be restricted by power
bars, high-nap carpets, etc.
Otherwise, sufficient air flow cannot
be guaranteed.
Ventilating the installation area
To ensure trouble-free operation, the
dryer must be perfectly level.
^ Compensate for floor irregularities by
turning the threaded feet in or out.
32
The air needed for drying is
extracted from the installation
space. You must therefore take
measures for sufficient room
ventilation, by opening windows for
instance.
Otherwise you can expect longer
running times and higher energy
consumption.
Installation and connection
Electrical connections
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
breakdown, grounding will reduce
the risk of electric shock by
providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an
equipment grounding conductor
and a grounding plug. The plug
must be plugged into an appropriate
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
WARNING – Improper connection of
the equipment grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician or
service representative or personnel
if you are in doubt as to whether the
appliance is properly grounded.
The dryer comes with a 5 ft long,
12/4 AWG cord and a NEMA 14-30 P
plug.
It should be connected to a
120/208-240 V, 30 A, 60 Hz AC power
supply. A 3 pole-4 wire grounding
power outlet (NEMA type 14-30 R) is
necessary.
The dryer is equipped with a power
cable and plug ready for connection.
The plug must always be accessible to
facilitate disconnecting the dryer from
the electrical supply.
To eliminate a potential fire source, the
dryer should NEVER be connected by
means of extension cords, or by
multi-outlet power strips or the like.
The appliance data plate indicates the
nominal power consumption and the
approbiate fuse capacity. Please
compare the information on the data
plate with the electrical network data.
Do not modify the plug provided
with the appliance! If it will not fit the
outlet, have a proper outlet installed
by a qualified electrician.
33
Installing the dryer vent
General
Important
Avoid:
– very long ducting systems.
– too many sharp bends or corners.
The dryer should only be operated
when the moist air produced by
drying is ducted to the outside, by
means of: . .
. . . a flexible venting hose, or piping
connected to the dryer, or
. . . a direct connection to a
through-wall pipe.
– The appliance should not be
electrically connected while the
venting is being installed.
– The ducting outlet (for instance, a
wall pipe) is to be located so that the
moist air . .
. . . cannot be drawn back into the
dryer installation space;
. . . will cause no structural damage
or unacceptable nuisance.
– Air required for drying is drawn from
the installation space.
Consequently, ensure that there is
sufficient room ventilation when
drying to prevent possible
asphyxiation from the possibility of
expelled gasses being drawn back
into the room, as well as to prevent
much longer drying times; for
example:
- Open windows;
- fitting unblockable air
inlets in the external wall;
- install window switches, so
that the dryer can only be
turned on when the window is
open.
34
Otherwise you will have less efficient
drying and increased time and energy
consumption.
Use:
– for ventilation ducting:
rigid or flexible metal ducting with a
100 mm diameter.
– for venting to the outside:
a wall pipe or window vent kit.
Procedure
^ First measure the duct length
required. From this, calculate the
total duct length and determine the
required diameter (see the next
pages).
Note that a greater overall duct
length requires a larger pipe
diameter.
^ Then, decide which type of ducting
you wish to use (see "Installing
Venting Systems" in this section).
Installing the dryer vent
Calculating total duct length
Each of bends and differing
components of the dryer's venting
creates its own frictional resistance to
the flow of the exhaust air. This frictional
resistance is expressed in a
comparative duct length. The
comparative duct length indicates the
length of a smooth straight pipe (of the
same diameter), producing the same
resistance to air flow as the original
ducting component (Table I).
Adding together the comparative duct
lengths of all components reveals the
total duct length. The total duct length
is a calculated value that compares
how long a smooth straight venting
pipe would have to be for the same air
flow.
Since an internal pipe diameter
strongly affects flow's resistance, a vent
with a total duct length exceeding 20
m requires a larger diameter (Table II).
Table I
Components
Comparative duct length
Flexible ducting
–
–
–
1.8 m
1.5 m
1 m laid straight
45° bend
(Bend radius = 0.25 m)
90° bend
(Bend radius = 0.25 m)
2.5 m
Vent hose(flexible or Alu-Flex)
–
–
–
1.0 m
1 m laid straight or 1 m straight
pipe
45° bend
(Bend radius = 0.25 m)
90° bend
(Bend radius = 0.25 m)
0.6 m
0.8 m
Wall vent kit or window vent kit
–
–
with grill insert
with non-return flap (hinged flap)
Non-return flap* for integration
into the vent ducting
(see section "d Vent collector
duct")
3.8 m
1.5 m
14.3 m
11.0 m
Flat duct (for stacked
arrangement)
1.0 m
Left or right dryer vent opening
* Miele accessory available on order
Procedure
1. Measure the distance requiring
straight ducting. Multiply this value
by the corresponding comparative
pipe length from Table I.
2. Determine the number of bends and
components required. Add their
comparative lengths together using
Table I.
Table II
Maximum permissible
total duct length
Diameter required
20 m
40 m
100 m
100 mm
125 mm
150 mm
3. Add together all the comparative
lengths thus determined: Thus you
obtain the total duct length.
4. From Table II, determine which
internal duct diameter is required for
the total duct length.
35
Installing the dryer vent
Rear or side exhaust
connection
Calculation example
At the rear
Dryer is delivered with this connection
open.
^ Install the vent duct as described on
the following pages.
Sideways to left or right
A
Wall pipe, with grill insert
= 1 x 3.8 m Comparative duct
length
B/D
2 elbows, 90°
= 2 x 0.8 m Comparative duct
length
C
= 1.6 m
0.5 m plastic piping
= 0.5 x 1 m Comparative duct
length
E
= 3.8 m
= 0.5 m
Left side vent opening
= 1 m Comparative duct length
= 1.0 m
Total duct length
= 6.9 m
Result: Total duct length is less than 20
m (as per Table II). Therefore a pipe
diameter of 100 mm is adequate.
^ Unscrew the cover
(counterclockwise).
^ Refit the cover securely in the rear
vent outlet.
^ Install the vent duct as described on
the following pages.
36
Installing the dryer vent
Overview of vent systems
On this and the following pages you will
find descriptions of four venting
systems (a b c d) that can be
installed on the dryer.
a Flexible metal duct hose
Using the adapter provided, you can
easily install a vending duct hose
(diameter 100 mm).
You require
– a duct hose (flexible or Alu-Flex).
– a wall pipe kit or a window vent kit.
^ Install the pipe (2) on the dryer using
an adapter (1).
Examples are shown on the next
page.
37
Installing the dryer vent
Examples:
Connection to exhaust flue
Window vent
1. Pipe with connector
1. Window vent kit (fitted in plexiglass
pane)
2. Adapter for flexible vent hose
2. Adapter for flexible vent hose
3. Exhaust flue, insulated against damp
,Ducting must not be connected
to a fireplace or gas flue that is in
use, nor to ducting which ventilates
rooms with fireplaces.
38
Installing the dryer vent
b Dryer vent systems from
metal piping
Example
Smooth piping makes sense where
the vented air has to be carried on a
considerable distance.
A pipe offers less resistance to the
discharge air than does, for instance,
a flexible ventilation duct. Time and
energy consumption improve with
smooth piping.
You require
– a connector adapter* (diameter 100
mm).
– a wall pipe kit or a window vent vent
kit.
– Metal venting pipe from a builder or
plumbing supplier(diameter 100
mm). If a larger pipe diameter is
needed, adapters are necessary (for
example, to transition from 100 to
125 mm diameters).
1. Wall vent kit
2. Adapter
3. Metal dryer venting pipe,
diameter 4" (100 mm).
* Miele accessory available on order
^ Install the pipe (2) in the dryer using
an adapter (1).
39
Installing the dryer vent
c Connecting directly to a wall
vent
Side view:
If you can place the dryer directly
against the external wall of the room,
this vent configuration is
advantageous. The short overall pipe
length has a beneficial effect on time
and energy consumption. However,
you must make an opening in the wall
to install the wall kit.
You will need a wall pipe kit as well as a
flexible spacer ring.
A Before breaking through the wall... . .
. . . read the installation instructions
accompanying the kit.
. . . and study the following
dimensional drawings.
1. Wall pipe
2. Flexible foam gasket
View from above:
B Fit the flexible foam gasket (2) onto
the wall pipe adapter (1).
C Push the dryer up against the wall.
1. Wall pipe
2. Flexible foam gasket
40
Installing the dryer vent
d Vent collector duct
To prevent condensed water buildup in
the non-operating dryers:
^ For each dryer, install a non-return
flap R directly on the collector duct.
You will need an optional Miele
accessory* (see right) for this.
When installing from 3 to a maximum
of 5 dryers, the pipe diameterD must
be enlarged.
Number
of
dryers
Pipe diameter multiplication
factor from Table II
1-2
3
4-5
1
1,25
1,5
1
2
3
4
Connection to connection duct
Miele non-return flap*
additional Miele Adapter*
Vent hose, flexible
^ Press the non-return flap(2) fully into
the Adapter (3).
41
Installing the dryer vent
Washer-dryer stack
WTV 414 Stacking unit* :
A = 94.2 cm
B = 172 cm
* Miele accessory available on order
42
Technical data
Height
850 mm
Width
Depth
595 mm
634 mm
Depth with door open
Can be pushed under a worktop
– Height
– Width
1,074 mm
Yes
850 mm
600 mm
Suitable for stacking
Weight
Yes
46 kg
Drum Volume
Length of power cord
111 liters
2m
Voltage
Connected load (Watts)
Rated current (Amps)
Light bulb wattage
see data plate
Test certifications granted
43
Programmable functions
for changing
standard values
As needed, you can use
programmable functions to adapt
the dryer electronics to changing
requirements.
You can alter programmable
functions at any time.
44
Programmable functions
Extending the range of drying
levels
You can extend the range of the
drying levels for many of the
programs:
Rotary iron+
(dryer than Rotary Iron).
Hand iron+
(dryer than Hand iron).
Normal +
(dryer than Normal).
Additionally, the Extra dry level can
be selected for the Delicates and
Denim Jeans programs.
This programmable function is also
effective in the following programs:
Normal, Wrinkle free*, Delicates*,
Mixed, Denim/Jeans
(* no Rotary iron+).
For programming and saving in the
memory, follow steps A to E.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
– P and 0 flash alternatively in the
display (default setting).
The number appearing alternatively
with P means:
0 Default setting
I Drying range steps added
(Mixed indicator light also flashes)
D Pressing the Start/Stop button
switches from one to the other.
E Using the I-On/0-Off jk button,
switch the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
To select the extended drying level:
^ Select a program.
^ Press the drying level button
repeatedly until one or two indicator
lights come on.
– Indicator lights Extra dry and Normal
= Normal+
– Indicator lights Normal and Hand
iron = Hand iron+
– Indicator lights Hand iron and Rotary
iron = Rotary iron+
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
– The Gentle indicator light flashes
twice briefly.
45
Programmable functions
Adjusting buzzer volume
The buzzer has two volumes.
For programming and saving in
memory, follow steps A to E.
This function is programmed using the
buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
D Press the Gentle button once.
– The Gentle indicator light flashes
briefly four times.
– P and 0 flash alternatingly in the
display (default setting).
46
The number appearing alternatingly
with P means:
0 Buzzer normal
(default setting)
I Buzzer loud
(Mixed indicator light also flashes)
E Pressing the Start/Stop button
switches from one number to the
other, and you simultaneously hear
the buzzer setting.
F Using the I-On/0-Off jk button,
switch the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
Programmable functions
Set memory function
The electronics memorizes any
selected program with extra options.
The duration of a Smoothing program
will also be stored in memory.
These settings will be used for the
next drying. They can be accepted,
or changed by using the buttons.
The number appearing alternatingly
with P means:
I Memory
(Mixed indicator light also flashes)
0 no Memory
(default setting)
E Pressing the Start/Stop button
switches from one to the other.
For programming and saving in
memory, follow steps A to E.
F Using the I-On/0-Off jk button,
switch the dryer off.
The programmable function is
programmed using the buttons.
The programming is now stored in
memory. You can change it again at
any time.
Precondition:
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
D Press the Gentle button twice.
– The Gentle indicator light flashes
briefly six times.
– P and 0 flash alternatingly in the
display (default setting).
47
Programmable functions
Extending cooldown time
You can individually lengthen the
cooldown phase the occurs before
the end of a program. Fabrics will be
more completely cooled down.
The number appearing alternatingly
with P means:
0 Default setting
I Five minutes longer cooldown time
(Mixed indicator light will flash once)
– can be extended by two stages.
2 Ten minutes longer cooldown time
(Mixed indicator light will also flash
twice)
– it does not function for Smoothing
programme.
E Pressing the Start/Stop button
switches from one to the other.
For programming and saving in
memory, follow steps A to E.
F Using the I-On/0-Off jk button,
switch the dryer off.
The programmable function is
programmed using the buttons.
The programming is now stored in
memory. You can change it again at
any time.
Cooldown time
Precondition:
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
D Press the Gentle button three times.
– The Gentle indicator light flashes
briefly seven times.
– P and 0 flash alternatingly in the
display (default setting).
48
Programmable functions
Change function of Filter/Vent
indication
Lint should be removed after drying.
At the same time, the Filter/Vent
indicator light reminds you to do so
as soon as a certain degree of lint
has accumulated. You can yourself
decide which degree of lint
accumulation will trigger that
reminder.
Determine by trial and error which of
the four options responds to your
drying practices.
For programming and saving in
memory, follow steps A to E.
The programmable function is
programmed using the buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
The number appearing alternatingly
with P means:
0 The Filter/Vent indicator is
deactivated
I The Filter/Vent indicator comes on
only when there is a heavy lint
buildup
(Mixed control light additionally
flashes once)
2 default setting
(the Mixed indicator light also flashes
twice)
3 The Filter/Vent indicator will come
on when there is only a light lint
buildup
(The Mixed indicator light also
flashes three times)
E Pressing the Start/Stop button
switches from one to the other.
F Using the I-On/0-Off jk button,
switch the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
D Press the Gentle button four times.
– The Gentle indicator light flashes
once slowly.
– P and 2 flash alternatingly in the
display (default setting).
49
Programmable functions
Adjust keypad tone
An audible tone sounds every time a
button is pressed.
The number appearing alternatingly
with P means:
0 no Keypad tone
(default setting)
For programming and saving in
memory, follow steps A to E.
I Keypad tone on
(Mixed indicator light also flashes)
The programmable function is
programmed using the buttons.
E Pressing the Start/Stop button
switches from one to the other.
Precondition:
F Using the I-On/0-Off jk button,
switch the dryer off.
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
D Press the Gentle button five times.
– The Gentle indicator light flashes
once slowly and once briefly.
– P and 0 flash alternatingly in the
display (default setting).
50
The programming is now stored in
memory. You can change it again at
any time.
Programmable functions
Changing water conductivity
setting
,This programmable function
should be adjusted only when
residual water content is erroneously
determined owing to the extreme
softness of the water.
D Press the Gentle button six times.
– The Gentle indicator light flashes
once slowly and twice briefly.
– P and 0 flash alternatingly in the
display (default setting).
The number appearing alternatingly
with P means:
Important condition
0 Default setting
The water in which fabrics are washed
may be extremely soft with a
conductivity value less than 150 μS/cm.
Drinking water conductivity can be
ascertained from your local water
supplier.
I Lower conductivity setting
(Mixed indicator light also flashes)
Activate this programmable function
only if the above-mentioned
condition applies.
Otherwise the drying result will be
unsatisfactory.
The programming is now stored in
memory. You can change it again at
any time.
E Pressing the Start/Stop button
switches from one to the other.
F Using the I-On/0-Off jk button,
switch the dryer off.
For programming and saving in
memory, follow steps A to E.
The function is programmed using the
buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
A Press Start/Stop and keep it pressed
it during steps B-C.
B Press the I-On/0-Off jk button in.
Wait until the Start/Stop button lights up
continuously . . .
C . . . then release the Start/Stop
button.
51
Alteration rights reserved/ 2811
M.-Nr. 09 174 580 / 00
Download PDF
Similar pages