Sublime Hardware Revision 2 Release Notes

Sublime
Hardware Revision 2
Release Notes
Revision: 2.6.6
2015-12-09
nevion.com
Overview
2
1 Overview
This document contains information about firmware releases for VikinX Sublime hardware revision 2. The release note is cumulative, each chapter describing changes since the previous released
version.
Upgrade of Sublime firmware is performed using the Nevion Configurator tool either via IP or
serial connection. For more information please refer to the Nevion Configurator online help.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
3
2 Firmware Releases
2.1 Release 2.6.6 (AJ)
Date: 2015-12-09
Firmware version:
• Main uC: 2.6.6
• VIT uC: R2A
Changes:
• Fixed an issue that made the device stop responding on Ethernet when connected to a
network with a lot of broadcast traffic.
• Fixed a memory leak that could make the device stop responding on Ethernet.
2.2 Release 2.6.5 (AH)
Date: 2014-05-13
Firmware version:
• Main uC: 2.6.5
• VIT uC: R2A
Changes:
• Fixed issue with unstable reporting of power alarm on MRP
2.3 Release 2.6.4 (AG)
Date: 2014-01-09
Firmware version:
• Main uC: 2.6.4
• VIT uC: R2A
Changes:
• New feature: Added support for alarms on MRP (TCP/IP)
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
4
2.4 Release 2.6.3 (AF)
Date: 2013-07-17
Firmware version:
• Main uC: 2.6.3
• VIT uC: R2A
Changes:
• Ethernet autonegotiation handling is updated to only support 100Mb/s-half or 10Mb/shalf.
2.5 Release 2.6.2 (26)
Date: 2012-02-14
Firmware version:
• Main uC: 2.6.2
• VIT uC: R2A
Changes:
• New feature: Support for SL-3GHD128128-RC added.
• New feature: Support for “si”-command in MRP implemented.
• New feature: Generate alarm if fan on SFP module backplane stops.
• Improvement: Support for 3GHD video format in “Router request” command added to
NCB protocol.
• Bug: Fixed a problem where the panel needed to be “Enabled” twice if NCB cable wasn’t
connected when powered up.
2.6 Release 2.6.1 (25)
Date: 2011-09-23
Firmware version:
• Main uC: 2.6.1
• VIT uC: R2A
Changes:
• Bug in SL-D32P+: Port configuration problem when in extension loop fixed.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
5
• Bug in SL-D32P+: Problem with connecting a fixed port to another fixed port with the
same configuration fixed. This only orrured when in extension loop.
2.7 Release 2.6.0 (24)
Date: 2011-06-21
Firmware version:
• Main uC: 2.6.0
• VIT uC: R2A
Changes:
• New feature: Make it possible to configure redundant connection between a Sublime
panel and a Multicon system.
• Improvement: Grass Valley Native Protocol updated to close the connection if no data has
been received for two minutes.
• Bug: A panel connected to a router on NCB will now get the correct status when powered
up.
• Bug: Take button is now working on panel-configurations with salvos only.
• Bug: In rare conditions, powering off a panel can make the router it was connected to
uncontrollable.
2.8 Release 23
Date: 2011-05-03
Firmware version:
• Main uC: 2.5.4
• VIT uC: R2A
Changes:
• New feature: Sublime routers can be controlled using Thomson Native Protocol.
• New feature: Support output protect button on panel.
• Improvement: More alarm statuses reported when Alarm Status Request is called on
Leitch Pass-Through protocol.
• Improvement: A/V toggle button functionallity updated.
• Improvement: In NCB loop, the Sublime will act more like Compact when powering up.
• Bug: Panel will reconnect if router re-powered.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
6
• Bug: Possible buffer overrun in TCP interface fixed.
• Bug: Invalid product keys not handled correct.
• Bug: Panel will not show invalid status for outputs bigger then the matrix size.
2.9 Release 22
Date: 2011-03-18
Firmware version:
• Main uC: 2.5.3
• VIT uC: R2A
Changes:
• New feature: Signal presence reported on MRP on SL-D32P+.
• Bug in 2.5.x: A SL-D32P, not in extension loop, the controller might reboot when sending
a sequence of crosspoint commands.
• Bug: On panel with GPI interface, changing more then 10 GPI inputs at the same time
didn’t work.
• Bug: On panel with GPI interface, configured with “Dynamic fallback mode”, “Switch
before release” and “Joystick release mode”, the fallback input might change during normal operation.
• Bug: SL-D32P is reporting wrong router format on NCB protocol.
2.10 Release 21
Date: 2011-03-01
Firmware version:
• Main uC: 2.5.2
• VIT uC: R2A
Changes:
• Bug: Multiple SL-D32P+ in extension loop, XY-mode and source orientation didn’t update each other with correct status.
• Bug in 2.5.x: Unable to upgrade firmware on vit module.
• Improvement: Only allow configuration changed from one configuration software at a
time.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
7
2.11 Release 20
Date: 2011-02-21
Firmware version:
• Main uC: 2.5.1
• VIT uC: R2A
Changes:
• Support for SL-D32P in XY-mode added again (This was temporarely removed in version
2.5.0).
• Improvement: On SL-D32P+, raise alarms if communication problems on extension loop.
2.12 Release 19
Date: 2011-02-02
Firmware version:
• Main uC: 2.5.0
• VIT uC: R2A
Changes:
• Note: This release does not support SL-D32P in XY-mode!
• New feature: Support for SL-D32P+ added.
• Bug in 2.4.x: When connecting to MRP the connection is sometimes immediately closed.
• Bug in 2.4.x: A false SFP alarm is sometimes activated on SL-D32P / SL-D32P+.
• Improvement: On SL-D32P / SL-D32P+, pin 5 on the RS-422 ports are all connected with
a weak pull-up to +5V.
2.13 Release 18
Date: 2010-09-27
Firmware version:
• Main uC: 2.4.1
• VIT uC: R2A
Changes:
• Bug in 2.4.0: EQ on all inputs set to bypass mode.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
8
• Improvement: Support new matrix module in 8x8 and 16x16 digital video routers.
2.14 Release 17
Date: 2010-09-10
Firmware version:
• Main uC: 2.4.0
• VIT uC: R2A
Changes:
• New feature: Support for routers with optical modules added.
• New feature: Sublime routers can be controlled using Leitch Pass-Through protocol.
• New feature: Report system name and description to configuration tool which makes it
capable of handling systems with only Sublime devices.
• New feature: Possible to enable new features by adding product keys.
2.15 Release 16
Date: 2010-03-08
Firmware version:
• Main uC: 2.3.4
• VIT uC: R2A
Changes:
• Bug: SL-3GHD128128 does sometimes not start properly.
• Improvement: Wait until signal is stable before reporting it as present to control system.
2.16 Release 15
Data: 2010-03-02
Firmware version:
• Main uC: 2.3.3
• VIT uC: R2A
Changes:
• Bug: Upgrading from firmware version 2.1.4 or earlier could lead to strange matrix status
like locked outputs.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
9
• Bug: SL-D32P in D1616 mode and source oriented (DIP 6 and 9 ON) wasn’t working
properly.
2.17 Release 14
Date: 2010-01-28
Firmware version:
• Main uC: 2.3.2
• VIT uC: R2A
Changes:
• Bug: Panel configuration wasn’t working with some older bootloaders.
2.18 Release 13
Date: 2010-01-22
Firmware version:
• Main uC: 2.3.1
• VIT uC: R2A
Changes:
• Bug: Reporting version information from vit module fixed.
• Bug: Bootloader updated. This is needed to be able to upgrade firmware over TCP/IP
(Firmware upgrade over TCP/IP is only for routers and panels with controller card revision 3 or newer.)
• Bug: Power alarms on SL-3GHD128128 fixed.
• Bug: With heavy load the router might stop switching.
• Bug: All outputs connected to input one at start-up for 64x64 and smaller routers. This
bug only occur in 2.3.0.
2.19 Release 12
Date: 2009-12-23
Firmware version:
• Main uC: 2.3.0
• VIT uC: R2A
Changes:
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
10
• New feature: Support for SL-3GHD128128 added.
• New feature: Possible to bypass re-clocker.
• New feature: Possible to disable equalizer.
• New feature: Signal presence reported on MRP.
• New feature: CRC on MRP supported.
• New feature: Possible to upgrade firmware over TCP/IP. (Only for routers with controller
card revision 3.)
2.20 Release 11
Date: 2009-08-28
Firmware version:
• Main uC: 2.2.0
• VIT uC: R2A
Changes:
• Support for non-square crosspoint modules added.
• Bug: Some modules was reported with wrong format.
2.21 Release 10
Date: 2009-08-10
Firmware version:
• Main uC: 2.1.5
• VIT uC: R2A
Changes:
• Bug: A unit might stop accepting incoming connections on MRP after a period of time.
• Bug: Power-up status on a SL-D32P in source oriented mode was wrong.
• Bug: A router without embedded panel is failing if sending a lock command on MRP on
a level that is not present.
• Bug: Lock status on MRP in incorrect on SL-D32P.
• Bug: Status on salvo buttons fixed.
• Improvement: Locking crosspoints on a router from another router with embedded panel
is now possible.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
11
• Improvement: A ported data router will report it’s level format as ported on MRP.
• Improvement: Input buttons with automatic offset implemented. This is useful when
input extension on 16x2 routers is used.
• Improvement: Setting a SL-D32P in D1616-mode will not overwrite port direction used
in D32P-mode.
• Improvement: Possible to define “Disconnect” and “Undefined” input buttons and to
have “Disconnect” and “Undefined” in salvo buttons.
2.22 Release 9
Date: 2009-01-29
Firmware version:
• Main uC: 2.1.4
• VIT uC: R2A
Changes:
• Bug: Power interruption for 180-250 ms was not handled correctly.
• Improvement: Do not activate all LEDs in the buttons when upgrading firmware.
2.23 Release 8
Date: 2008-11-26
Firmware versions:
• Main uC: 2.1.3
• VIT uC: R2A
Changes:
• Bug: Startup status when a router is in 2, 3 or 4 layers router mode fixed.
• Bug: Protocol configuration updated to handle 16x2 routers with input extension.
2.24 Release 7
Date: 2008-10-15
Firmware versions:
• Main uC: 2.1.2
• VIT uC: R2A
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
12
Changes:
• Bug: Input extension on SL-AD1602-110 fixed.
• Bug: Audio 16x2 routers with input extension to 128x2 can control input 128 from embedded panel.
• Improvement: “Take” button is always enabled if no “Take on/off” button is present on
the panel.
2.25 Release 6
Date: 2008-09-03
Firmware versions:
• Main uC: 2.1.1
• VIT uC: R2A
Changes:
• Critical bug in 2.1.0 fixed.
2.26 Release 5
Date: 2008-08-28
Firmware versions:
• Main uC: 2.1.0
• VIT uC: R2A
Changes:
• Possible to configure protocols. Choose between MRP, NCB and NCB without Sublime
extensions.
• Remove the limit that made Sublime panels unable to control levels higher then 16.
• Bug in input extension on SL-T1602 fixed.
• Radiated emission (EMC) reduced.
• Accept <CR><LF> in MRP commands.
• Accept syntax command on MRP.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Firmware Releases
13
2.27 Release 4
Date: 2008-02-05
Firmware versions:
• Main uC: 2.0.3
• VIT uC: R2A
Changes:
• Support for GPIO panels added.
• Switching times are made configurable.
• Controlling multiple levels from a panel is improved.
2.28 Release 3
Date: 2007-12-19
Firmware versions:
• Main uC: 2.0.2
• VIT uC: R1A
Changes:
• Critical bug, which could disable switching on a router, is fixed. This bug did not occur
on SL-D32P.
2.29 Release 2
Date: 2007-12-07
Firmware versions:
• Main uC: 2.0.1
• VIT uC: P1B
Changes:
• Bug in destination lock status response on SL-D32P fixed.
• Bug on SL-D32P when “Power-up mode” is on is fixed; port configuration is not deleted.
• “Router orientation” DIP added to SL-D32P.
• The device is rebooting correctly after a configuration change is done.
• Allow switching a SL-D32P in “wrong” direction regarding port configuration.
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
14
• Disconnect all ports on SL-D32P when “Router orientation” or “D1616 mode” is changed.
• Panels updated to control data routers better.
• Support for destination protect added on MRP protocol.
2.30 Release 1
Date: 2007-10-04
Firmware versions:
• Main uC release 2.0.0
• VIT uC release P1B
Files:
• sublime_firmware-2.0.0.bin
• sublime_firmware-2.0.0.sap
Changes:
• Initial release
ID: rn_sublime_rev2
Sublime Hardware Revision 2 Release Notes Rev. 2.6.6
Download PDF
Similar pages