QuickSpecs
Aruba 3810 Switch Series
Overview
Aruba 3810 Switch Series
Models
Aruba 3810M 24G 1-slot Switch
Aruba 3810M 48G 1-slot Switch
Aruba 3810M 24G PoE+ 1-slot Switch
Aruba 3810M 48G PoE+ 1-slot Switch
Aruba 3810M 16SFP+ 2-slot Switch
Aruba 3810M 40G 8 HPE Smart Rate PoE+ 1-slot Switch
JL071A
JL072A
JL073A
JL074A
JL075A
JL076A
Key features
Powerful Aruba Layer 3 switch series with backplane stacking, low latency and resiliency
HPE Smart Rate for high-speed multigigabit capacity and PoE+ power
Modular line rate 10GbE and 40GbE ports for wireless aggregation
Full PoE+ on all 48 ports for power-hungry high-speed wireless APs
Ready for innovative SDN applications with OpenFlow support
Product overview
The Aruba 3810 Switch Series is an industry-leading mobile campus access solution for enterprises, SMBs,
and branch office networks. With HPE Smart Rate multi-gigabit ports for high-speed IEEE 802.11ac
devices, the Aruba 3810 will prepare your network for tomorrow. Rightsize deployment and back haul
capacity with modular 10GbE and 40GbE uplinks.
Full PoE+ provisioning available on 48-ports. Dual, redundant, hot-swappable power supplies and
innovative backplane stacking technology delivers resiliency and scalability in a convenient 1U form factor.
Advanced Layer 2 and 3 feature set with OSPF, IPv6, IPv4 BGP, robust QoS and policy-based routing are
included with no software licensing.
With support for OpenFlow, the Aruba 3810 is ready to take advantage of SDN applications such as HPE
Network Visualizer, Optimizer, and Protector Applications. Delivers consistent wired and wireless user
experience by supporting ClearPass Policy Manager and AirWave Network Management.
Features and benefits
Software-defined networking
OpenFlow
is a key technology that enables SDN by allowing separation of the data (packet forwarding) and
control (routing decision) paths
Unified Wired and Wireless
ClearPass Policy Manager support
unified wired and wireless policies using Aruba ClearPass Policy Manager
HTTP redirect function:
supports HPE Intelligent Management Center (IMC) bring your own device (BYOD) solution
Switch auto-configuration
automatically configures switch for rogue AP detection, add VLAN, and set PoE priority when Aruba
AP is detected
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 1
QuickSpecs
Aruba 3810 Switch Series
Overview
Quality of Service (QoS)
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS
policies such as setting priority level and rate limit to selected traffic on a per-port or per-VLAN basis
Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol,
TCP/UDP port number, source port, and DiffServ
Bandwidth shaping:
- Port-based rate limiting: provides per-port ingress-/egress-enforced increased bandwidth
- Classifier-based rate limiting: uses an access control list (ACL) to enforce increased bandwidth
for ingress traffic on each port
- Reduced bandwidth: provides per-port, per-queue egress-based reduced bandwidth
Remote intelligent mirroring
mirrors selected ingress/egress traffic based on an ACL, port, MAC address, or VLAN to a local or
remote HPE 8200 zl, 6600, 6200 yl, 5400 zl, or 3500 switch anywhere on the network
Remote monitoring (RMON), Extended RMON (XRMON), and sFlow v5
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Traffic prioritization
allows real-time traffic classification into eight priority levels that are mapped to eight queues
Management
Friendly port names
allows assignment of descriptive names to ports
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating
easy mapping by network management applications
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's
login; an audit trail documents activity
Multiple configuration files
stores easily to the flash image
Dual flash images
provides independent primary and secondary operating system files for backup while upgrading
Out-of-band Ethernet management port
enables management over a separate physical management network; and keeps management traffic
segmented from network data traffic
Comware CLI
- Comware-compatible CLI
bridges the experience of Hewlett Packard Enterprise Comware CLI users who are using the
ProVision CLI
- Display and fundamental Comware CLI commands
are natively embedded in the switch CLI; display output is formatted as on Comware-based
switches; fundamental commands provide Comware-familiar initial switch setup
- Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct
ProVision software CLI command
Zero-Touch ProVisioning (ZTP)
uses settings in DHCP to enable ZTP with Aruba AirWave Network Management
Unidirectional Link Detection (UDLD)
support HPE UDLD and DLDP protocols to monitor a cable between two switches and shut down the
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 2
QuickSpecs
Aruba 3810 Switch Series
Overview
ports on both ends if a broken link is detected, preventing network problems such as loops
Connectivity
Jumbo frames
on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote
backup and disaster-recovery services
IEEE 802.3at PoE+
provides up to 30 W per port to IEEE 802.3at-complaint PoE/PoE+-powered devices such as video IP
phones, IEEE 802.11n wireless access points, and advanced pan/zoom/tilt security cameras
Pre-standard PoE support
detects and provides power to pre-standard PoE devices (refer to the list of supported devices in the
product FAQs, which can be accessed at http://www.hpe.com/networking)
Choice of uplinks:
- SFP+ uplink models: provide fiber-optic (up to 70 km) or direct-attach-cable (DAC) connectivity
- 10GBASE-T uplink models: offer 10GbE speeds, using standard RJ-45 connectors and
standard twisted-pair cabling up to 100 m
Auto-MDIX
provides automatic adjustments for straight-through or crossover cables on all RJ-45 ports
IPv6:
- IPv6 host: enables switch management in an IPv6 network
- Dual stack (IPv4 and IPv6): transitions IPv4 to IPv6, supporting connectivity for both protocols
- MLD snooping: forwards IPv6 multicast traffic to the appropriate interface
- IPv6 ACL/QoS: supports ACL and QoS for IPv6 traffic
- IPv6 routing: supports static, RIPng, OSPFv3 routing protocols
- 6in4 tunneling: supports encapsulation of IPv6 traffic in IPv4 packets
- Security: provides RA guard, DHCPv6 protection, dynamic IPv6 lockdown, and ND snooping
Performance
Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory
buffering that best meet the requirements of the network applications
Energy-efficient design:
- 80 PLUS Silver Certified power supply: increases power efficiency and savings
- Energy-efficient Ethernet (EEE) support: reduces power consumption in accordance with IEEE
802.3az
Meshed stacking technology:
- High-performance stacking: provides up to 336 Gb/s of stacking throughput; each 4-port
stacking module can support up to 42 Gb/s in each direction per stacking port
- Ring, chain, and mesh topologies: support up to a 10-member ring or chain and 5-member fully
meshed stacks; meshed topologies offer increased resiliency vs. a standard ring
- Virtualized switching: provides simplified management as the switches appear as a single
chassis when stacked
HPE ProVision ASIC architecture
is designed with the latest ProVision ASIC, providing very low latency, increased packet buffering, and
adaptive power consumption
Resiliency and high availability
Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available routed
environments in IPv4 and IPv6 networks
Nonstop switching and routing
improves network availability to better support critical applications, such as unified communication and
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 3
QuickSpecs
Aruba 3810 Switch Series
Overview
mobility; traffic will continue to be forwarded during failovers, when the backup member of the stack
becomes the commander
IEEE 802.3ad Link Aggregation Protocol (LACP) and Hewlett Packard Enterprise port trunking
support up to 24 trunks, each with up to 8 links (ports) per trunk
IEEE 802.1s Multiple Spanning Tree
provides high link availability in multiple VLAN environments by allowing multiple spanning trees;
provides legacy support for IEEE 802.1d and IEEE 802.1w
Dual hot-swappable power supplies
- Increased resiliency: provides secondary power supply to enable complete switch power
redundancy in case of power line or supply failure
- Increased PoE+ power: provides the secondary power supply to increase the total available
PoE+ power
Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a
server or switch to connect to two switches using one logical trunk for redundancy and load sharing
SmartLink
provides easy-to-configure link redundancy of active and standby links
Layer 2 switching
IEEE 802.1ad QinQ
increases the scalability of an Ethernet network by providing a hierarchical structure; connects
multiple LANs on a high-speed campus or metro network
VLAN support and tagging
supports the IEEE 802.1Q standard and 4096 VLANs simultaneously
IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
MAC-based VLAN
provides granular control and security; uses RADIUS to map a MAC address/user to specific VLANs
Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible
with PVST+
Hewlett Packard Enterprise switch meshing
dynamically load balances across multiple active redundant links to increase available aggregate
bandwidth; allows concurrent Layer 3 routing
GVRP and MVRP
allows automatic learning and dynamic assignment of VLANs
Layer 3 services
Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF),
improving diagnostic capability
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
User datagram protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet
broadcast addresses; and helps prevent server spoofing for UDP services such as DHCP
DHCP server
centralizes and reduces the cost of IPv4 address management
Bidirectional Forwarding Detection (BFD)
enables link connectivity monitoring and reduces network convergence time for static routing,
OSPFv2, and VRRP
Layer 3 routing
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 4
QuickSpecs
Aruba 3810 Switch Series
Overview
Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
OSPF
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
Policy-based routing
makes routing decisions based on policies set by the network administrator
Border Gateway Protocol (BGP)
provides IPv4 Border Gateway Protocol routing, which is scalable, robust, and flexible
Routing Information Protocol (RIP)
provides RIPv1, RIPv2, and RIPng routing
Security
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure shell
encrypts all transmitted data for secure remote CLI access over IP networks
Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
Port security
allows access only to specified MAC addresses, which can be learned or specified by the
administrator
MAC address lockout
prevents particular configured MAC addresses from connecting to the network
Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be
caused by malicious attacks is detected
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or
unauthorized copying of a switch configuration file
Switch management logon security
helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or
SNMPv3
ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP
traffic
Virus throttling
detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents the virus
from spreading across the routed VLANs or bridged interfaces without requiring external appliances
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN assignment
specific to each authenticated network user
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged
BPDU attacks
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address
spoofing
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
STP root guard
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 5
QuickSpecs
Aruba 3810 Switch Series
Overview
protects the root bridge from malicious attacks or configuration mistakes
Management Interface Wizard
helps secure management interfaces such as SNMP, Telnet, SSH, SSL, Web, and USB at the desired
level
Security banner
displays a customized security policy when users log in to the switch
Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
ACLs
provide filtering based on the IP field, source/destination IP address/subnet and source/destination
TCP/UDP port number on a per-VLAN or per-port basis
Multiple authentication methods
- IEEE 802.1X
authenticates multiple IEEE 802.1X users per port; prevents a user from "piggybacking" on
another user's authentication
- Web-based authentication
authenticates from Web browser for clients that do not support 802.1X supplicant
- MAC-based authentication
authenticates client with the RADIUS server based on client's MAC address
- Concurrent authentication modes
enables a switch port to accept up to 32 sessions of 802.1X, Web, and MAC authentication
Private VLAN
provides network security by restricting peer-to-peer communication to prevent a variety of malicious
attacks; typically a switch port can only communicate with other ports in the same community and/or
an uplink port, regardless of VLAN ID or destination MAC address
Convergence
IP multicast snooping (data-driven IGMP)
prevents flooding of IP multicast traffic
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to
automatically configure network devices such as IP phones
PoE allocations
supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate
PoE power for more efficient energy savings
IP multicast routing (requires the premium license)
includes PIM sparse and dense modes to route IP multicast traffic
Auto VLAN configuration for voice
- RADIUS VLAN
uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP
phones
- CDPv2
uses CDPv2 to configure legacy IP phones
Local MAC Authentication
assigns attributes such as VLAN and QoS using locally configured profile that can be a list of MAC
prefixes
Warranty and support
Limited Lifetime Warranty
see http://www.hpe.com/networking/warrantysummary for warranty and support information included
with your product purchase.
Software releases
to find software for your product, refer to http://www.hpe.com/networking/support; for details on the
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 6
QuickSpecs
Aruba 3810 Switch Series
Overview
software releases available with your product purchase, refer to
http://www.hpe.com/networking/warrantysummary
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 7
QuickSpecs
Aruba 3810 Switch Series
Configuration
Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
Aruba 3810M 24G 1-slot Swch
24 RJ-45 autosensing 10/100/1000 ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL071A
Aruba 3810M 48G 1-slot Swch
48 RJ-45 autosensing 10/100/1000 ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL072A
Aruba 3810M 24G PoE+ 1-slot Swch
24 RJ-45 autosensing 10/100/1000 PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL073A
Aruba 3810M 48G PoE+ 1-slot Swch
48 RJ-45 autosensing 10/100/1000 PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL074A
Aruba 3810M 16SFP+ 2-slot Swch
16 fixed 1000/10000 SFP+ ports
min=0 \ max=16 SFP+ Transceivers
1 open stacking module slot
2 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
Aruba 3810M 40G 8SR PoE+ 1-slot Swch
40 RJ-45 autosensing 10/100/1000 PoE+ ports
8 RJ-45 1/2.5/5/XGT PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL075A
See
Configuration
NOTE: 1
JL076A
Configuration Rules:
NOTE 1
The following Transceivers install into this Switch (For the 1000/10000 SFP+
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 8
QuickSpecs
Aruba 3810 Switch Series
Configuration
Ports):
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC SX Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 3m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 5m Direct Attach Copper Cable
J4860C
J4859C
J4858C
J9142B
J9143B
J8177C
J9150A
J9153A
J9151A
J9152A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
Box Level Integration CTO Models
CTO Solution SKU
HP 38xx CTO Switch Solution
SSP trigger SKU
JG501A
CTO Switch Chassis
Aruba 3810M 24G 1-slot Swch
24 RJ-45 autosensing 10/100/1000 ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL071A
See
Configuration
NOTE: 10, 11
Aruba 3810M 48G 1-slot Swch
48 RJ-45 autosensing 10/100/1000 ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL072A
See
Configuration
NOTE: 10, 11
Aruba 3810M 24G PoE+ 1-slot Swch
24 RJ-45 autosensing 10/100/1000 PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL073A
See
Configuration
NOTE: 10, 11
Aruba 3810M 48G PoE+ 1-slot Swch
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
JL074A
Page 9
QuickSpecs
Aruba 3810 Switch Series
Configuration
48 RJ-45 autosensing 10/100/1000 PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
See
Configuration
NOTE: 10, 11
Aruba 3810M 16SFP+ 2-slot Swch
16 fixed 1000/10000 SFP+ ports
min=0 \ max=16 SFP+ Transceivers
1 open stacking module slot
2 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL075A
See
Configuration
NOTE: 1, 10,
11
Aruba 3810M 40G 8SR PoE+ 1-slot Swch
40 RJ-45 autosensing 10/100/1000 PoE+ ports
8 RJ-45 1/2.5/5/XGT PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL076A
See
Configuration
NOTE: 10, 11
Configuration Rules:
NOTE 1
The following Transceivers install into this Switch (For the 1000/10000 SFP+
Ports):
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC SX Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 3m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 5m Direct Attach Copper Cable
NOTE 10
If the Switch Chassis is to be Factory Integrated (CTO), Then the #0D1 is
required on the Switch Chassis and integrated to the JG501A - HP 3800
CTO Enablement. (Min 1/Max 1 Switch per SSP)
NOTE 11
If this Switch is selected, Then a Minimum of 1 factory integrated accessory
must be ordered and integrated to CTO chassis. See Menu below, option
must have a #0D1 to be integrated to the CTO Chassis.
J4860C
J4859C
J4858C
J9142B
J9143B
J8177C
J9150A
J9153A
J9151A
J9152A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
Rack Level Integration CTO Models
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 10
QuickSpecs
Aruba 3810 Switch Series
Configuration
Aruba 3810M 24G 1-slot Swch
24 RJ-45 autosensing 10/100/1000 ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL071A
See
Configuration
NOTE: 10, 11
Aruba 3810M 48G 1-slot Swch
48 RJ-45 autosensing 10/100/1000 ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL072A
See
Configuration
NOTE: 10, 11
Aruba 3810M 24G PoE+ 1-slot Swch
24 RJ-45 autosensing 10/100/1000 PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL073A
See
Configuration
NOTE: 10, 11
Aruba 3810M 48G PoE+ 1-slot Swch
48 RJ-45 autosensing 10/100/1000 PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL074A
See
Configuration
NOTE: 10, 11
Aruba 3810M 16SFP+ 2-slot Swch
16 fixed 1000/10000 SFP+ ports
min=0 \ max=16 SFP+ Transceivers
1 open stacking module slot
2 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL075A
See
Configuration
NOTE: 1, 10,
11
Aruba 3810M 40G 8SR PoE+ 1-slot Swch
40 RJ-45 autosensing 10/100/1000 PoE+ ports
8 RJ-45 1/2.5/5/XGT PoE+ ports
1 open stacking module slot
1 open uplink module slot
1 Power Supply required (Max 2)
1U - Height
JL076A
See
Configuration
NOTE: 10, 11
Configuration Rules:
NOTE 1
The following Transceivers install into this Switch (For the 1000/10000 SFP+
Ports):
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC SX Transceiver
HP X122 1G SFP LC BX-D Transceiver
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
J4860C
J4859C
J4858C
J9142B
Page 11
QuickSpecs
Aruba 3810 Switch Series
Configuration
HP X122 1G SFP LC BX-U Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 3m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 5m Direct Attach Copper Cable
NOTE 10
If switch is 0D1 to Racks, then the J9583A#0D1 is also required.
NOTE 11
If the CTO Switch Chassis needs to be racked, Then the CTO Base Model
needs to integrate (with #0D1) to the HPE Network Rack.
J9143B
J8177C
J9150A
J9153A
J9151A
J9152A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
Enter the following menu selections as integrated to the CTO Model X switch above if order
is factory built.
Modules
Stacking Modules
System (std 0 // max=1) User Selection (min 0 / max=1) per Chassis
Aruba 3810M 4-port Stacking Module
min=0 \ max=4 Stacking cables
JL084A
See
Configuration
NOTE: 1
Configuration Rules:
NOTE 1
The following Cables install into this Module: (Use #B01 quoted to switch if
switch is CTO) - if applicable
Aruba 3800/3810M 0.5m Stacking Cable
Aruba 3800/3810M 1m Stacking Cable
Aruba 3800/3810M 3m Stacking Cable
J9578A
J9665A
J9579A
Uplink Modules
JL071A, JL072A, JL073A, JL074A, JL076A Only System (std 0 // max 1) User Selection
(min 0 / max 1) per Chassis
JL075A Only System (std 0 // max 2) User Selection (min 0 / max 2) per Chassis
Aruba 3810M 1QSFP+ 40GbE Module
min=0 \ max=1 QSFP+ Transceiver
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
JL078A
See
Configuration
NOTE: 1
Page 12
QuickSpecs
Aruba 3810 Switch Series
Configuration
Aruba 3810M 2QSFP+ 40GbE Module
min=0 \ max=2 QSFP+ Transceiver
JL079A
See
Configuration
NOTE: 1, 3
Aruba 3810M 4SFP+ Module
min=0 \ max=4 SFP+ Transceivers
JL083A
See
Configuration
NOTE: 2
Configuration Rules:
NOTE 1
NOTE 2
NOTE 3
Remarks:
The following Transceivers install into this Module: (Use #0D1 or #B01 if
switch is CTO) - if applicable
HP X142 40G QSFP+ MPO SR4 Transceiver
HP X142 40G QSFP+ LC LR4 SM Transceiver
HP X142 40G QSFP+ MPO eSR4 300M XCVR
HP X242 40G QSFP+ to QSFP+ 1m Direct Attach Copper Cable
HP X242 40G QSFP+ to QSFP+ 3m Direct Attach Copper Cable
HP X242 40G QSFP+ to QSFP+ 5m Direct Attach Copper Cable
JH231A
JH232A
JH233A
JH234A
JH235A
JH236A
The following Transceivers install into this Switch (For the 1000/10000 SFP+
Ports):
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC SX Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 3m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 5m Direct Attach Copper Cable
J4860C
J4859C
J4858C
J9142B
J9143B
J8177C
J9150A
J9153A
J9151A
J9152A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
This module is only available for the following switches:
Aruba 3810M 48G 1-slot Swch
Aruba 3810M 48G PoE+ 1-slot Swch
Aruba 3810M 40G 8SR PoE+ 1-slot Swch
JL072A
JL074A
JL076A
Watson Only Blue NOTE - Although these switches are compatible with HPE
Smart Rate modules, they do not provid PoE+ power.
Transceivers
SFP Transceivers
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 13
QuickSpecs
Aruba 3810 Switch Series
Configuration
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC SX Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X121 1G SFP RJ45 T Transceiver
J4860C
J4859C
J4858C
J9142B
J9143B
J8177C
SFP+ Transceivers
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X242 10G SFP+ SFP+ 1m DAC Cable
HP X242 10G SFP+ SFP+ 3m DAC Cable
HP X242 10G SFP+ SFP+ 7m DAC Cable
HP X244 10G XFP SFP+ 1m DAC Cable
HP X244 10G XFP SFP+ 3m DAC Cable
HP X244 10G XFP SFP+ 5m DAC Cable
J9153A
J9150A
J9151A
J9152A
J9281B#B01
J9283B#B01
J9285B#B01
J9300A#B01
J9301A#B01
J9302A#B01
QSFP+ Transceivers
HP X142 40G QSFP+ MPO SR4 Transceiver
HP X142 40G QSFP+ LC LR4 SM Transceiver
HP X142 40G QSFP+ MPO eSR4 300M XCVR
HP X242 40G QSFP+ to QSFP+ 1m DAC Cable
HP X242 40G QSFP+ to QSFP+ 3m DAC Cable
HP X242 40G QSFP+ to QSFP+ 5m DAC Cable
JH231A
JH232A
JH233A
JH234A#B01
JH235A#B01
JH236A#B01
Internal Power Supplies
System (std 0 // max=2) User Selection (min 1 / max=2) per Switch
Aruba X371 12VDC 250W PS
JL085A
See
Configuration
NOTE: 1, 3, 4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JL085A #B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JL085A #B2C
High Volt Power Supply to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JL085A #B2E
Aruba X372 54VDC 680W PS
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
JL086A
Page 14
QuickSpecs
Aruba 3810 Switch Series
Configuration
See
Configuration
NOTE: 2, 3, 4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JL086A #B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JL086A #B2C
High Volt Power Supply to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JL086A #B2E
Aruba X372 54VDC 1050W PS
JL087A
See
Configuration
NOTE: 2, 3, 4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JL087A #B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JL087A #B2C
High Volt Power Supply to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JL087A #B2E
Configuration Rules:
NOTE 1
If this Power supply is selected, then JL071A, JL072A, JL075A must be the
switch its installed into.
NOTE 2
If this Power supply is selected, Then JL073A, JL074A, JL076A must be the
switch its installed into.
NOTE 3
Localization required on orders without #B2B or #B2C options.
NOTE 4
When Switches are Factory Racked with this power supply, Then #B2B, or
#B2C should be the Defaulted Power Cable option on the Power Supplies.
(See Drop down remark in “Internal Power Supplies” section.)
Remarks:
Drop down under power supply should offer the following options and
results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America,
Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for
Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson
Default for BTO and Box Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option.
(Offered only in North America, Mexico, Taiwan, and Japan)
Cables
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 15
QuickSpecs
Aruba 3810 Switch Series
Configuration
Stacking Cables
HP E3800 0.5m Stacking Cable
HP E3800 1m Stacking Cable
HP E3800 3m Stacking Cable
J9578A#B01
J9665A#B01
J9579A#B01
Multi-Mode Cables
HP .5m Multi-mode OM3 LC/LC FC Cable
HP 1m Multi-mode OM3 LC/LC FC Cable
HP 2 m Multimode OM3 LC/LC FC Cable
HP 5 m Multimode OM3 LC/LC FC Cable
HP 15 m Multimode OM3 LC/LC FC Cable
HP 30 m Multimode OM3 LC/LC FC Cable
HP 50 m Multimode OM3 LC/LC FC Cable
HP Premier Flex LC/LC OM4 2f 1m Cbl
HP Premier Flex LC/LC OM4 2f 2m Cbl
HP Premier Flex LC/LC OM4 2f 5m Cbl
HP Premier Flex LC/LC OM4 2f 15m Cbl
HP Premier Flex LC/LC OM4 2f 30m Cbl
HP Premier Flex LC/LC OM4 2f 50m Cbl
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
Switch Enclosure Options
Rack Mount Kit
HP X410 1U Univ 4-post Rack Mnt Kit
J9583A
See
Configuration
NOTE: 1
Configuration Rules:
NOTE 1
If this switch is factory installed in HPE Network Racks, Then the
J9583A#0D1 is required.
Fan Tray
Aruba 3810 Switch Fan Tray
This is a Spare Only
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
JL088A
Page 16
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Aruba 3810M 24G 1-slot Switch (JL071A)
Included accessories 1 Aruba 3810 Switch Fan Tray (JL088A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 24 support MACSec
Supports a maximum of 4 SFP+ ports or 1 40GbE ports, with optional module
1 open module slot
Supports a maximum of 4 SFP+ ports or 1 40GbE ports, with optional module
Additional ports and 1 stacking module slot
slots
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 dual-personality (RJ-45 or USB micro-B)
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
includes: 1 x JL088A
1 fan tray slot
Switch ships with 1 JL088A fan tray installed. Spares ordered separately.
Physical
Dimensions
17.42(w) x 16.98(d) x 1.73(h) in (44.25 x 43.13 x 4.39 cm)
characteristics
(1U height)
Weight
12.76 lb (5.79 kg)
Memory and
P2020 Dual Core @ 1.2 GHz, 4 GB DDR3 SDRAM, 1 GB SD Card
processor
Dual ARM Coretex A9 @ 1 GHz, 2 GB DDR3 SDRAM; Packet buffer size: 13.5 MB
Internal
Mounting and
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
enclosure
included); Horizontal surface mounting only
Performance
IPv6 Ready Certified
1000 Mb Latency
< 2.8 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.8 µs (FIFO 64-byte packets)
40 Gbps Latency
< 1.5 µs (FIFO 64-byte packets)
Throughput
up to 95.2 Mpps (64-byte packets)
Routing/Switching
160 Gbps
capacity
Switch fabric speed
169 Gbps
Routing table size
10000 entries (IPv4), 5000 entries (IPv6)
MAC address table
64000 entries
size
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
15% to 95% @ 104°F (40°C), noncondensing
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 15% to 90% @ 149°F (65°C), noncondensing
relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 39 dB, Pressure: 22.8 dB
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 17
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Safety
Emissions
Immunity
Management
Services
EN 60950/IEC 60950; UL 60950; UL 60950-1; CAN/CSA 22.2 No. 60950; EN 60825;
CSA 22.2 60950-1; EN62479:2010; EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013; EN 62368-1, Ed. 2; IEC 60950-1:2005 Ed.2; Am
1:2009+A2:2013; IEC 60825:2007; EN60850-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1; UL 62368-1 Ed.2
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A; EN 60950-1:2006
+A11:2009 +A1:2010 +A12:2011+A2:2013
Generic
EN55022: 2010
EN
EN55024: 2010
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
magnetic field
Voltage dips and
IEC 61000-4-11; >95% reductions, 0.5 period; 30%
interruptions
reduction, 25 periods
Harmonics
EN61000-3-2:2006 +A1:2009 +A2:2009 Class A
Flicker
EN61000-3-3:2008
Aruba AirWave Network Management; IMC - Intelligent Management Center;
Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); In-line and out-of-band; Out-of-band management
(serial RS-232c or micro usb)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area,
please contact your local Hewlett Packard Enterprise sales office.
Aruba 3810M 48G 1-slot Switch (JL072A)
Included accessories 1 Aruba 3810 Switch Fan Tray (JL088A)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 48 support MACSec
1 open module slot
Supports a maximum of 4 SFP+ ports or 2 40GbE ports, with optional module
Additional ports and 1 stacking module slot
slots
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 dual-personality (RJ-45 or USB micro-B)
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
includes: 1 x JL088A
1 fan tray slot
Switch ships with 1 JL088A fan tray installed. Spares ordered separately.
Physical
Dimensions
17.42(w) x 16.98(d) x 1.73(h) in (44.25 x 43.13 x 4.39 cm)
characteristics
(1U height)
Weight
13.20 lb (5.99 kg)
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 18
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Memory and
processor
Mounting and
enclosure
Performance
Environment
Safety
Emissions
Immunity
Management
P2020 Dual Core @ 1.2 GHz, 4 GB DDR3 SDRAM, 1 GB SD Card
Dual ARM Coretex A9 @ 1 GHz, 2 GB DDR3 SDRAM; Packet buffer size: 13.5 MB
Internal
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); Horizontal surface mounting only
IPv6 Ready Certified
1000 Mb Latency
< 2.8 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.8 µs (FIFO 64-byte packets)
40 Gbps Latency
< 1.5 µs (FIFO 64-byte packets)
Throughput
up to 190.5 Mpps (64-byte packets)
Routing/Switching
320 Gbps
capacity
Switch fabric speed
338 Gbps
Routing table size
10000 entries (IPv4), 5000 entries (IPv6)
MAC address table
64000 entries
size
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
15% to 95% @ 104°F (40°C), noncondensing
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 15% to 90% @ 149°F (65°C), noncondensing
relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 38 dB, Pressure: 21.8 dB
EN 60950/IEC 60950; UL 60950; UL 60950-1; CAN/CSA 22.2 No. 60950; EN 60825;
CSA 22.2 60950-1; EN62479:2010; EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013; EN 62368-1, Ed. 2; IEC 60950-1:2005 Ed.2; Am
1:2009+A2:2013; IEC 60825:2007; EN60850-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1; UL 62368-1 Ed.2
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A; EN 60950-1:2006
+A11:2009 +A1:2010 +A12:2011+A2:2013
Generic
EN55022: 2010
EN
EN55024: 2010
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
magnetic field
Voltage dips and
IEC 61000-4-11; >95% reductions, 0.5 period; 30%
interruptions
reduction, 25 periods
Harmonics
EN61000-3-2:2006 +A1:2009 +A2:2009 Class A
Flicker
EN61000-3-3:2008
Aruba AirWave Network Management; IMC - Intelligent Management Center;
Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); In-line and out-of-band; Out-of-band management
(serial RS-232c or micro usb)
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 19
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Services
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area,
please contact your local Hewlett Packard Enterprise sales office.
Aruba 3810M 24G PoE+ 1-slot Switch (JL073A)
Included accessories 1 Aruba 3810 Switch Fan Tray (JL088A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+);
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 24
support MACSec
1 open module slot
Supports a maximum of 4 SFP+ ports or 1 40GbE ports, with optional module
Additional ports and 1 stacking module slot
slots
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 dual-personality (RJ-45 or USB micro-B)
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
includes: 1 x JL088A
1 fan tray slot
Switch ships with 1 JL088A fan tray installed. Spares ordered separately
Physical
Dimensions
17.42(w) x 16.98(d) x 1.73(h) in (44.25 x 43.13 x 4.39 cm)
characteristics
(1U height)
Weight
13.02 lb (5.91 kg)
Memory and
P2020 Dual Core @ 1.2 GHz, 4 GB DDR3 SDRAM, 1 GB SD Card
processor
Dual ARM Coretex A9 @ 1 GHz, 2 GB DDR3 SDRAM; Packet buffer size: 13.5 MB
Internal
Mounting and
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
enclosure
included); Horizontal surface mounting only
Performance
IPv6 Ready Certified
1000 Mb Latency
< 2.8 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.8 µs (FIFO 64-byte packets)
40 Gbps Latency
< 1.5 µs (FIFO 64-byte packets)
Throughput
up to 95.2 Mpps (64-byte packets)
Routing/Switching
160 Gbps
capacity
Switch fabric speed
169 Gbps
Routing table size
10000 entries (IPv4), 5000 entries (IPv6)
MAC address table
64000 entries
size
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
15% to 95% @ 104°F (40°C), noncondensing
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 15% to 90% @ 149°F (65°C), noncondensing
relative humidity
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 20
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Safety
Emissions
Immunity
Management
Services
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 48 dB, Pressure: 30.7 dB
EN 60950/IEC 60950; UL 60950; UL 60950-1; CAN/CSA 22.2 No. 60950; EN 60825;
CSA 22.2 60950-1; EN62479:2010; EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013; EN 62368-1, Ed. 2; IEC 60950-1:2005 Ed.2; Am
1:2009+A2:2013; IEC 60825:2007; EN60850-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1; UL 62368-1 Ed.2
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A; EN 60950-1:2006
+A11:2009 +A1:2010 +A12:2011+A2:2013
Generic
EN55022: 2010
EN
EN55024: 2010
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
magnetic field
Voltage dips and
IEC 61000-4-11; >95% reductions, 0.5 period; 30%
interruptions
reduction, 25 periods
Harmonics
EN61000-3-2:2006 +A1:2009 +A2:2009 Class A
Flicker
EN61000-3-3:2008
Aruba AirWave Network Management; IMC - Intelligent Management Center;
Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); In-line and out-of-band; Out-of-band management
(serial RS-232c or micro usb)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area,
please contact your local Hewlett Packard Enterprise sales office.
Aruba 3810M 48G PoE+ 1-slot Switch (JL074A)
Included accessories 1 Aruba 3810 Switch Fan Tray (JL088A)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+);
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 48
support MACSec
1 open module slot
Supports a maximum of 4 SFP+ ports or 2 40GbE ports, with optional module
Additional ports and 1 stacking module slot
slots
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 dual-personality (RJ-45 or USB micro-B)
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
includes: 1 x JL088A
1 fan tray slot
Switch ships with 1 JL088A fan tray installed. Spares ordered separately.
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 21
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Physical
characteristics
Memory and
processor
Mounting and
enclosure
Performance
Environment
Safety
Emissions
Immunity
Dimensions
17.42(w) x 16.98(d) x 1.73(h) in (44.25 x 43.13 x 4.39 cm)
(1U height)
Weight
13.62 lb (6.18 kg)
P2020 Dual Core @ 1.2 GHz, 4 GB DDR3 SDRAM, 1 GB SD Card
Dual ARM Coretex A9 @ 1 GHz, 2 GB DDR3 SDRAM; Packet buffer size: 13.5 MB
Internal
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); Horizontal surface mounting only
IPv6 Ready Certified
1000 Mb Latency
< 2.8 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.8 µs (FIFO 64-byte packets)
40 Gbps Latency
< 1.5 µs (FIFO 64-byte packets)
Throughput
up to 190.5 Mpps (64-byte packets)
Routing/Switching
320 Gbps
capacity
Switch fabric speed
338 Gbps
Routing table size
10000 entries (IPv4), 5000 entries (IPv6)
MAC address table
64000 entries
size
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
15% to 95% @ 104°F (40°C), noncondensing
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 15% to 90% @ 149°F (65°C), noncondensing
relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 42 dB, Pressure: 26 dB
EN 60950/IEC 60950; UL 60950; UL 60950-1; CAN/CSA 22.2 No. 60950; EN 60825;
CSA 22.2 60950-1; EN62479:2010; EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013; EN 62368-1, Ed. 2; IEC 60950-1:2005 Ed.2; Am
1:2009+A2:2013; IEC 60825:2007; EN60850-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1; UL 62368-1 Ed.2
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A; EN 60950-1:2006
+A11:2009 +A1:2010 +A12:2011+A2:2013
Generic
EN55022: 2010
EN
EN55024: 2010
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
magnetic field
Voltage dips and
IEC 61000-4-11; >95% reductions, 0.5 period; 30%
interruptions
reduction, 25 periods
Harmonics
EN61000-3-2:2006 +A1:2009 +A2:2009 Class A
Flicker
EN61000-3-3:2008
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 22
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Management
Services
Aruba AirWave Network Management; IMC - Intelligent Management Center;
Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); In-line and out-of-band; Out-of-band management
(serial RS-232c or micro usb)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area,
please contact your local Hewlett Packard Enterprise sales office.
Aruba 3810M 16SFP+ 2-slot Switch (JL075A)
Included accessories 1 Aruba 3810 Switch Fan Tray (JL088A)
I/O ports and slots
16 SFP+ fixed 1000/10000 SFP+ ports; Duplex: 100BASE-TX: half or full;
1000BASE-T: full only; Ports 1 - 16 support MACSec
2 open module slots
Supports a maximum of 8 SFP+ ports or 2 40GbE ports, with optional module
Additional ports and 1 stacking module slot
slots
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 dual-personality (RJ-45 or USB micro-B)
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
includes: 1 x JL088A
1 fan tray slot
Switch ships with 1 JL088A fan tray installed. Spares ordered separately.
Physical
Dimensions
17.42(w) x 16.98(d) x 1.73(h) in (44.25 x 43.13 x 4.39 cm)
characteristics
(1U height)
Weight
13.28 lb (6.02 kg)
Memory and
P2020 Dual Core @ 1.2 GHz, 4 GB DDR3 SDRAM, 1 GB SD Card
processor
Dual ARM Coretex A9 @ 1 GHz, 2 GB DDR3 SDRAM; Packet buffer size: 13.5 MB
Internal
Mounting and
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
enclosure
included); Horizontal surface mounting only
Performance
IPv6 Ready Certified
1000 Mb Latency
< 2.8 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.8 µs (FIFO 64-byte packets)
40 Gbps Latency
< 1.5 µs (FIFO 64-byte packets)
Throughput
up to 285.7 Mpps (64-byte packets)
Routing/Switching
480 Gbps
capacity
Switch fabric speed
508 Gbps
Routing table size
10000 entries (IPv4), 5000 entries (IPv6)
MAC address table
64000 entries
size
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
15% to 95% @ 104°F (40°C), noncondensing
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 23
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Safety
Emissions
Immunity
Management
Services
Nonoperating/Storage 15% to 90% @ 149°F (65°C), noncondensing
relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 39 dB, Pressure: 22.3 dB
EN 60950/IEC 60950; UL 60950; UL 60950-1; CAN/CSA 22.2 No. 60950; EN 60825;
CSA 22.2 60950-1; EN62479:2010; EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013; EN 62368-1, Ed. 2; IEC 60950-1:2005 Ed.2; Am
1:2009+A2:2013; IEC 60825:2007; EN60850-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1; UL 62368-1 Ed.2
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A; EN 60950-1:2006
+A11:2009 +A1:2010 +A12:2011+A2:2013
Generic
EN55022: 2010
EN
EN55024: 2010
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
magnetic field
Voltage dips and
IEC 61000-4-11; >95% reductions, 0.5 period; 30%
interruptions
reduction, 25 periods
Harmonics
EN61000-3-2:2006 +A1:2009 +A2:2009 Class A
Flicker
EN61000-3-3:2008
Aruba AirWave Network Management; IMC - Intelligent Management Center;
Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); In-line and out-of-band; Out-of-band management
(serial RS-232c or micro usb)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area,
please contact your local Hewlett Packard Enterprise sales office.
Aruba 3810M 40G 8 HPE Smart Rate PoE+ 1-slot Switch (JL076A)
Included accessories 1 Aruba 3810 Switch Fan Tray (JL088A)
I/O ports and slots
40 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+);
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 40
support MACSec
8 RJ-45 HPE Smart Rate Multi-Gigabit ports; Ports 1 - 8 support MACSec
1 open module slot
Supports a maximum of 4 SFP+ ports or 2 40GbE ports, with optional module
Additional ports and 1 stacking module slot
slots
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 dual-personality (RJ-45 or USB micro-B)
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 24
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Fan tray
Physical
characteristics
Memory and
processor
Mounting and
enclosure
Performance
Environment
Safety
Emissions
Immunity
includes: 1 x JL088A
1 fan tray slot
Switch ships with 1 JL088A fan tray installed. Spares ordered separately.
Dimensions
17.42(w) x 16.98(d) x 1.73(h) in (44.25 x 43.13 x 4.39 cm)
(1U height)
Weight
13.61 lb (6.17 kg)
P2020 Dual Core @ 1.2 GHz, 4 GB DDR3 SDRAM, 1 GB SD Card
Dual ARM Coretex A9 @ 1 GHz, 2 GB DDR3 SDRAM; Packet buffer size: 13.5 MB
Internal
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware
included); Horizontal surface mounting only
IPv6 Ready Certified
1000 Mb Latency
< 2.8 µs (FIFO 64-byte packets)
10 Gbps Latency
< 1.8 µs (FIFO 64-byte packets)
40 Gbps Latency
< 1.5 µs (FIFO 64-byte packets)
Throughput
up to 273.8 Mpps (64-byte packets)
Routing/Switching
480 Gbps
capacity
Switch fabric speed
508 Gbps
Routing table size
10000 entries (IPv4), 5000 entries (IPv6)
MAC address table
64000 entries
size
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
15% to 95% @ 104°F (40°C), noncondensing
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 15% to 90% @ 149°F (65°C), noncondensing
relative humidity
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 45 dB, Pressure: 27.9 dB
EN 60950/IEC 60950; UL 60950; UL 60950-1; CAN/CSA 22.2 No. 60950; EN 60825;
CSA 22.2 60950-1; EN62479:2010; EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013; EN 62368-1, Ed. 2; IEC 60950-1:2005 Ed.2; Am
1:2009+A2:2013; IEC 60825:2007; EN60850-1:2007 / IEC 60825-1: 2007 Class1
Class 1 Laser Products / Laser Klasse 1; UL 62368-1 Ed.2
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A; EN 60950-1:2006
+A11:2009 +A1:2010 +A12:2011+A2:2013
Generic
EN55022: 2010
EN
EN55024: 2010
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
magnetic field
Voltage dips and
IEC 61000-4-11; >95% reductions, 0.5 period; 30%
interruptions
reduction, 25 periods
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 25
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
Management
Services
Standards and
protocols
(applies to all
products in series)
Harmonics
EN61000-3-2:2006 +A1:2009 +A2:2009 Class A
Flicker
EN61000-3-3:2008
Aruba AirWave Network Management; IMC - Intelligent Management Center;
Command-line interface; Web browser; Configuration menu; Out-of-band
management (RJ-45 Ethernet); In-line and out-of-band; Out-of-band management
(serial RS-232c or micro usb)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area,
please contact your local Hewlett Packard Enterprise sales office.
BGP
RFC 1997 BGP Communities Attribute
RFC 2918 Route Refresh Capability
RFC 4271 A Border Gateway Protocol 4
(BGP-4)
RFC 4456 BGP Route Reflection: An
Alternative to Full Mesh Internal BGP
(IBGP)
RFC 4724 Graceful Restart Mechanism
for BGP
RFC 5492 Capabilities Advertisement
with BGP-4
Denial of service protection
CPU DoS Protection
Device management
RFC 1591 DNS (client)
RFC 2576 (Coexistence between SNMP
V1, V2, V3)RFC 2579 (SMIv2 Text
Conventions)
RFC 2580 (SMIv2 Conformance)
RFC 3416 (SNMP Protocol Operations
v2)RFC 3417 (SNMP Transport
Mappings)
HTML and telnet management
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1AX-2008 Link Aggregation
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by
Protocol and Port
IEEE 802.1w Rapid Reconfiguration of
Spanning Tree
IEEE 802.3ad Link Aggregation Control
Protocol (LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 4113 MIB for UDP
RFC 4213 Basic Transition Mechanisms
for IPv6 Hosts and Routers
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing
Architecture
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
RFC 5095 Deprecation of Type 0 Routing
Headers in IPv6
RFC 5340 OSPFv3 for IPv6
RFC 5453 Reserved IPv6 Interface
Identifiers
RFC 5519 Multicast Group Membership
Discovery MIB (MLDv2 only)
RFC 5722 Handling of Overlapping IPv6
Fragments
RFC 6620 FCFS SAVI
draft-ietf-savi-mix
MIBs
IEEE 802.1ap (MSTP and STP MIB's
only)
IEEE 8021-Bridge-MIB (2008)
IEEE 8021-Q-Bridge-MIB (2008)
RFC 1155 Structure & ID of Mgmt Info for
TCP/IP
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q
Bridge MIB
RFC 2737 Entity MIB (Version 2)
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 26
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 1918 Address Allocation for Private
Internet
RFC 2030 Simple Network Time Protocol
(SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 2548 (MS-RAS-Vendor only)
RFC 3046 DHCP Relay Agent
Information Option
RFC 3575 IANA Considerations for
RADIUS
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
RFC 5798 VRRP (exclude Accept Mode
and sub-sec timer)
RFC 5880 Bidirectional Forwarding
Detection
RFC 5905 Network Time Protocol
Version 4: Protocol and Algorithms
Specification
UDLD (Uni-directional Link Detection)
IP multicast
RFC 3376 IGMPv3
RFC 3973 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2080 RIPng for IPv6
RFC 2081 RIPng Protocol Applicability
Statement
RFC 2082 RIP-2 MD5
RFC 2375 IPv6 Multicast Address
Assignments
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over
Ethernet Networks
RFC 2710 Multicast Listener Discovery
(MLD) for IPv6
RFC 2925 Definitions of Managed
Objects for Remote Ping, Traceroute, and
Lookup Operations (Ping only)
RFC 3019 MLDv1 MIB
RFC 2787 VRRP MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 2932 IP (Multicast Routing MIB)
RFC 2933 IGMP MIB
RFC 4836 Managed Objects for 802.3
Medium Attachment Units (MAU)
RFC 7331 BFD MIB
Network management
IEEE 802.1AB Link Layer Discovery
Protocol (LLDP)
RFC 2819 Four groups of RMON: 1
(statistics), 2 (history), 3 (alarm) and 9
(events)
RFC 3176 sFlow
RFC 3411 SNMP Management
Frameworks
RFC 3412 Message Processing and
Dispatching for the Simple Network
Management Protocol (SNMP)
RFC 3413 Simple Network Management
Protocol (SNMP) Applications
RFC 3414 User-based Security Model
(USM) for version 3 of the Simple
Network Management Protocol (SNMPv3)
RFC 3415 View-based Access Control
Model (VACM) for the Simple Network
Management Protocol (SNMP)
RFC 3418 Management Information Base
(MIB) for the Simple Network
Management Protocol (SNMP)
RFC 5424 Syslog Protocol
ANSI/TIA-1057 LLDP Media Endpoint
Discovery (LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
RFC 3623 Graceful OSPF Restart
(Unplanned Outages only)
RFC 5340 OSPFv3 for IPv6
QoS/CoS
RFC 2474 DiffServ Precedence, including
8 queues/port
RFC 2597 DiffServ Assured Forwarding
(AF)
RFC 2598 DiffServ Expedited Forwarding
(EF)
Security
IEEE 802.1X Port Based Network Access
Control
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 27
QuickSpecs
Aruba 3810 Switch Series
Technical Specifications
RFC 3315 DHCPv6 (client only)
RFC 3484 Default Address Selection for
IPv6
RFC 3587 IPv6 Global Unicast Address
Format
RFC 3596 DNS Extension for IPv6
RFC 4022 MIB for TCP
RFC 4087 IP Tunnel MIB
Internets
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2021 RMONv2 MIB
RFC 2096 IP Forwarding Table MIB
RFC 2578 Structure of Management
Information Version 2 (SMIv2)
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 1321 The MD5 Message-Digest
Algorithm
RFC 1492 TACACS+
RFC 2818 HTTP Over TLS
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
RFC 3579 RADIUS Support For
Extensible Authentication Protocol (EAP)
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 28
QuickSpecs
Aruba 3810 Switch Series
Accessories
Aruba 3810 Switch Series accessories
Modules
Aruba 3810M 4-port Stacking Module
Aruba 3810M 4SFP+ Module
Aruba 3810M 1QSFP+ 40GbE Module
Aruba 3810M 2QSFP+ 40GbE Module
JL084A
JL083A
JL078A
JL079A
Transceivers
HP X111 100M SFP LC FX Transceiver
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X142 40G QSFP+ MPO SR4 Transceiver
HP X142 40G QSFP+ MPO eSR4 300M XCVR
HP X142 40G QSFP+ LC LR4 SM Transceiver
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 3m Direct Attach Copper Cable
HP 10G X244 XFP to SFP+ 5m Direct Attach Copper Cable
HP X242 40G QSFP+ to QSFP+ 1m Direct Attach Copper Cable
HP X242 40G QSFP+ to QSFP+ 3m Direct Attach Copper Cable
HP X242 40G QSFP+ to QSFP+ 5m Direct Attach Copper Cable
J9054C
J4858C
J4859C
J4860C
J8177C
J9142B
J9143B
J9150A
J9151A
J9152A
J9153A
JH231A
JH233A
JH232A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
JH234A
JH235A
JH236A
Cables
Aruba 3800/3810M 0.5m Stacking Cable
Aruba 3800/3810M 1m Stacking Cable
Aruba 3800/3810M 3m Stacking Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
J9578A
J9665A
J9579A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
Power Supply
Aruba X371 12VDC 250W 100-240VAC Power Supply
Aruba X372 54VDC 680W 100-240VAC Power Supply
Aruba X372 54VDC 1050W 110-240VAC Power Supply
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
JL085A
JL086A
JL087A
Page 29
QuickSpecs
Aruba 3810 Switch Series
Accessories
Fan Tray
Aruba 3810 Switch Fan Tray
JL088A
Mounting Kit
HP X410 1U Universal 4-post Rack Mounting Kit
J9583A
Date
11-Dec-2015
Version History
From Version 1 to
2
Action
Changed
Description of Change
Standards and protocols and Configuration Menu
updated
Sign up for updates
Rate this document
© Copyright 2015 Hewlett Packard Enterprise Development LP. The information
contained herein is subject to change without notice. The only warranties for Hewlett
Packard Enterprise products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. Hewlett Packard Enterprise shall not
be liable for technical or editorial errors or omissions contained herein.
To learn more, visit: http://www.hpe.com/networking
c04843019 - 15438 - Worldwide - V2 - 11-December-2015
DA - 15438 Worldwide QuickSpecs — Version 2 — 12.11.2015
Page 30
Download PDF
Similar pages