High Power Wireless Outdoor CPE

CPE
User's Manual
High Power Wireless Outdoor CPE
CPE
User's Manual
CATALOG
1.PRODUCT OVERVIEW .......................................................... 4
1.1FEATURES AND SPECIFICATIONS .............................................. 4
1.2 SYSTEM REQUIREMENTS ..................................................... 4
1.3 INSTALLATION ENVIRONMENT REQUIREMENTS ................................... 4
1.4 INSTALLATION DIAGRAM .................................................... 5
1.5 HARDWARE INSTALL ........................................................ 5
1.6DEFAULT SETTING .......................................................... 6
2.CONFIGURATION PREPARATION ................................................. 6
3.TYPICAL APPLICATION SCENARIOS ............................................. 7
3.1 CPEBRIDGE MODE .......................................................... 7
3.2 CPEGATEWAY MODE ......................................................... 8
3.3 CPE VPNMODE ............................................................. 8
3.4 APBRIDGE MODE ........................................................... 9
3.5 APGATEWAY MODE ......................................................... 10
3.6 AP VPNMODE ............................................................. 11
3.7 REPEATERMODE ........................................................... 13
4.DEVICE LOGIN AND STATUS PAGE ....... ОШИБКА! ЗАКЛАДКА НЕ ОПРЕДЕЛЕНА.
5.SET PAGED ................................................................ 15
5.1WIRELESS BASIC SETTINGS ................................................. 15
5.2WIRELESSADVANCED SETTINGS ............................................... 16
5.3LAN SETTINGS ............................................................ 17
5.4FIREWALL SETTINGS ................. ОШИБКА! ЗАКЛАДКА НЕ ОПРЕДЕЛЕНА.
5.4.1IP/PORT FILTER ........................................................ 18
5.4.2MACADDRESS FILTER ..................................................... 19
5.4.3URL FILTER ............................................................ 19
5.4.4PORT MAPPING .......................................................... 20
CPE
User's Manual
5.4.5 DMZHOST ........................................................... 20
5.4.6 DDNS .............................................................. 20
5.4.7REMOTE ACCESS CONTROL ......... ОШИБКА! ЗАКЛАДКА НЕ ОПРЕДЕЛЕНА.
5.5
TIME ZONE ......................................................... 21
5.6
LOG ............................................................... 21
5.7
FIRMWARE UPDATE ............. ОШИБКА! ЗАКЛАДКА НЕ ОПРЕДЕЛЕНА.
5.8
CONFIGURE BACKUP / RESTORE .. ОШИБКА! ЗАКЛАДКА НЕ ОПРЕДЕЛЕНА.
5.9
LOGIN PASSWORD MANAGEMENT ... ОШИБКА! ЗАКЛАДКА НЕ ОПРЕДЕЛЕНА.
5.10
QOSTO CONFIGURE ................................................... 22
5.11
ADMINISTRATION .................................................... 22
5.12
CANCELLATION ...................................................... 23
CPE
User's Manual
1. Product overview
1.1Features and specifications
 Product characteristics:
 Support PPPOE, PPTP, L2TP, dynamic IP and static IP Five kinds of broadband access
methods.
 Support UPnP,DDNS,VPN.
 Support for virtual servers, special applications, and DMZ hosts。
 Support SSID broadcast control and access control based on MAC address.
 Support WEP 64/128-bit encryption, 128 WPA bit standard encryption(TKIP/AES)
 Built in firewall, support for IP filtering, URL filtering and MAC address filtering.
 The built-in DHCP server can automatically assign IP addresses.
 Support software upgrade page.
 Advanced QOS bandwidth control, easy to manage network bandwidth.
1.2
System requirements
 Broadband Internet services, broadband connection cable and ISP account(Access
method for Modem/Cable Modem xDSL or Ethernet)
 Modem/Cable Modem ADSL with Ethernet RJ45 interface(Ethernet access is not
required)
 Network connections for each computer(Network card and cable connection is normal)
 System for supporting TCP/IP software(Windows 2000/XP/7/8/10System comes)
 Internet - Explorer 8 or higher
1.3 Installation environment requirements
 As far as possible to place the router far away from the heating device.
 Do not place the router in a dirty or damp place.
 Recommended usage environment for routers:

Temperature: 0 to40℃

Humidity: 5% to 90%RH
CPE
User's Manual
1.4 Installation diagram
1.5 Hardware install
Example:
(Or direct use of the device comes with the power adapter power supply.)
CPE
User's Manual
1.6 Default setting
The following table lists some of the important default settings for CPE, all of which will be
described in detail in the following sections. Default settings apply to most cases, if the default
settings are not in conformity with the actual network requirements, please manually set, please
refer to the relevant sections of this manual.
Option
Default setting
Default user
name/Passwo admin/admin
rd
LAN port
IP address
Wireless
network
IP address:
192.168.0.1
Subnet Mask:255.255.255.0
Interpretative
Use this
account to log on to the
statement
settings page based on Web. Can be
changed according to the need.
This is the LAN port on the AP default
IP address, LAN users can through the
address of the device to maintain,
according to the network needs to
change this address.
Default work in client mode
2. Configuration preparation
Before access to the Web configuration page of the device, the user's computer also needs to
meet some of the basic configuration requirements.
 User computer requirements
Installed Ethernet card;
Installed Web browser(Suggest using Microsoft IE 6 or more);
 Install and start the TCP/IP protocol.
 Setup the correct network settings
The default IP address of the device is 192.168.0.1, the subnet mask is 255.255.255.0.In the
installation of access to the device site settings page before, must know in advance the IP system
of the equipment, and to the computer Ethernet card specified IP address and the IP address of the
computer and access to the IP address of the device must be set in the same subnet.
 Check proxy server settings
If the current computer uses a proxy server to access the Internet, you must first ban the
proxy service.
(1) In the browser window, select【Tools /Internet options】Menu entry【Internet option】.
(2) 【 Internet options 】 Select the connection tab and click on the window<LAN
settings>Button.
CPE
User's Manual
(3)Confirmation that the use of proxy server option is not selected.If selected, cancel and
click OK.
3. Typical application scenarios
3.1 CPE Bridge mode
Wireless Settings Equipment operation mode is“Station”,WAN Settings“Bridge
or WDS Bridge”As shown in the following figure:
The typical network connection topology is shown in the following figure:
The main related configuration is as follows:
1) Configure wireless settings to work in station mode;
2) WAN Connection Type work in Bridge or WDS Bridge;
3) Configure CPE scan access AP.
(High speed transmission video application scenarios, the proposed use of
Bridge WDS)
CPE
User's Manual
3.2 CPE Gateway mode
Wireless Settings Equipment working mode is "Station",WAN Settings“DHCP/Static
IP/PPPoE”As shown in the following figure:
The typical network connection topology is shown in the following figure:
The main related configuration is as follows:
1) Wireless working in station mode in wireless setting;
2) Set WAN connection type to work in DHCP / static IP, PPPoE;
3) Configure the corresponding Settings IP in the WAN address or dial-up
account, access network.
3.3 CPE VPN mode
Wireless setup device working mode for "station", "Wan settings set to PPPT
/ L2TP"As shown in the following figure:
CPE
User's Manual
The typical network connection topology is shown in the following figure:
The main related configuration is as follows:
1) Configure Settings Wireless work in Station mode;
2) The WAN connection type in the wide area network is working at PPTP/L2TP;
3) Configure the corresponding Settings IP in the WAN address or VPN dial-up
account, access network.
3.4 AP Bridge mode
Wireless setting device working mode is "AP",The WAN is set to "bridge or WDS
bridge". As shown in the following figure:
CPE
User's Manual
The typical network connection topology is shown in the following figure:
The main related configuration is as follows:
1) Configure Settings
wireless work in AP mode;
2) Configuring WAN connection types in wide area network to work in bridge
/ Bridge;
3) Configure user client device scan access CPE device.
(High speed transmission video application scenarios, the proposed
use of Bridge WDS)
3.5 AP Gateway mode
Wireless device working mode is "AP",Wan is set to DHCP / IP, PPPoE, and"As
shown in the following figure:
CPE
User's Manual
The typical network connection topology is shown in the following figure:
The main related configuration is as follows:
1) Configure Settings wireless work in AP mode;
2) Configure the WAN connection type in the wan to work in DHCP / IP, PPPoE;
3) Configure the client device to scan the access CPE device, configure the
corresponding IP address or dial-up account access network in the CPE
device Settings WAN.
3.6 AP VPN mode
Wireless setting device working mode is "AP",WAN Settings“PPTP/L2TP”如 As
shown in the following figure:
CPE
User's Manual
The typical network connection topology is shown in the following figure:
The main related configuration is as follows:
1) Configure Settings
wireless work in AP mode;
2) The WAN connection type in the wide area network is working at PPTP/L2TP;
3) Configure the client device to scan the access CPE device, configure the
corresponding IP address or VPN dial-up account access network in the
CPE device Settings WAN.
CPE
User's Manual
3.7 Repeater mode
The wireless set working mode as a "repeater",Wan settings can be set to bridge
/ bridge / DHCP / static PPPoE, IP, PPTP, L2TP"As shown in the following figure:
The typical network connection topology is shown in the following figure:
That is:CEP work in the Station mode at the same time open AP mode coverage,
can achieve relay, relay transmission function.
The main related configuration is as follows:
1) Configure Settings wireless work in Repeater mode;
2) Configure WAN connection type mode in wide area network;
3) Configure the corresponding Settings IP in the WAN address or VPN dial-up
account, access network。
4) In the "Multi SSID" configuration CPE at the same time open the AP mode
SSID, encryption mode, etc,As shown in the following figure:
CPE
User's Manual
4. Device login and status page
Landing set WEB page:
 Open the IE browser, and the input device IP address (the address bar default address:
192.168.0.1),press enter;
 Pop-up login screen, enter the user name, password, press the OK button (factory default
user name admin, password admin) landing device management page.As shown in the
following figure:
Enter the user name, password and press will be determined after landing to the device
settings page, login default display system status page, view the running state through the
system, such as wide area network, wireless connection status, etc.
CPE
User's Manual
5. Set page
5.1 Wireless basic settings
This set of pages can be set up wireless working mode and WAN port operation mode
Wireless working mode:
CPE
User's Manual
Wireless encryption mode and key:
WAN Port working mode and parameter setting:
5.2 Wireless advanced settings
This set of pages can be set up wireless advanced parameters,As shown in the following
figure:
CPE
User's Manual
5.3 LAN settings
This set page can set the device IP address, DHCP parameters and the static IP list and so on.
CPE
User's Manual
5.4 Firewall settings
5.4.1 This setting page can set the device firewall parameters (Note: firewall
configuration can be configured only when the CPE device is working in the
gateway mode.)
5.4.2 IP/Port filter
IP/Port settings:
CPE
User's Manual
5.4.3 MAC Address filter
MAC Address filter settings:
5.4.4 URL filter
URL filter settings:
CPE
User's Manual
5.4.5 Virtual server
Virtual server settings:
5.4.6 DMZ
DMZ settings:
5.4.7 DDNS
DDNS settings:
CPE
User's Manual
5.4.8 Remote access control
Remote access control settings:
5.5 Time zone
Time zone settings:
5.6 System log
System log settings:
CPE
User's Manual
5.7 Firmware Update
Firmware Update settings:
5.8 Configure backup / restore
5.9 Login password management
5.10 QoS settings
5.11 Administration
Note: this feature is available only when the device is operating in the bridge mode
Users can through this configuration, to achieve the CPE device batch remote management,
need to cooperate with the "CPE centralized management server" use.
CPE
User's Manual
5.12 Cancellation
Click this option to log off the user login, the interface is updated to the user login interface.
Download PDF
Similar pages