alarm shop
High Resolution Varifocal Dome Camera SCD-2080 User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Before operating the camera, confirm the camera model and correct input power
voltage. To help you understand this manual thoroughly, we'll introduce our model
description.
nSCD-2080 SERIES
• NTSC MODEL SCD-2080N
• PAL MODEL
SCD-2080P
n MODEL DESCRIPTION
• SCD-2080X
_
SIGNAL SYSTEM
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
alarm shop
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING-Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
WARNING-To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Contents
Contents
Features
• Features…………………………………………………………………………… 5
• Precautions… …………………………………………………………………… 7
• Components and Accessories……………………………………………… 8
• Overview…………………………………………………………………………… 9
• Installation………………………………………………………………………… 9
■ Installation…………………………………………………………………………………… 9…
■ Adjust the panning, tilting and rotating while watching the monitor………………… 12
• Connection…………………………………………………………………………
■ Connecting to Monitor… ………………………………………………………………
■ Connecting to Power……………………………………………………………………
■ Using Coaxial Communications………………………………………………………
13
• Operating your Camera………………………………………………………
■ Menu Configuration………………………………………………………………………
■ Menu Setup… ……………………………………………………………………………
• LENS………………………………………………………………………………………
• EXPOSURE… ……………………………………………………………………………
• WHITE BALANCE… ……………………………………………………………………
• SSDR………………………………………………………………………………………
• BACKLIGHT………………………………………………………………………………
• SSNR3… …………………………………………………………………………………
• DAY/NIGHT… ……………………………………………………………………………
• SPECIAL… ………………………………………………………………………………
• EXIT… ……………………………………………………………………………………
15
13…
13…
14
SSDR
(Samsung Super Dynamic Range)
High Resolution
By adopting a diagonal 6mm(1/3") 410,000 (NTSC)
pixel, 470,000(PAL) pixel SONY CCD, the camera
produces clear picture quality with a horizontal
resolution of 600 TV lines in color and a horizontal
resolution of 700 TV lines in B/W mode.
Excellent Sensitivity
DIS (Digital Image Stabilizer)
The built-in high sensitivity COLOR CCD produces
a clear image.
- Color : 0.15Lux(50IRE, @F1.2), 0.0003LUX
(SENS-UP, x512)
- B/W : 0.001Lux(50IRE, @F1.2), 0.000002LUX
(SENS-UP, x512)
alarm shop
15…
16…
17…
17…
19…
20…
21…
23…
24…
25…
30
• Troubleshooting………………………………………………………………… 31
SSNR3 (Samsung Super Noise
Reduction) Function
The high-performance W-V DSP chip effectively
removes low-light gain noise and afterimage to
provide clear images even in dark environments.
The DIS function compensates for any camera
movement, to produce more stable pictures.
Communication
Coaxial communication methods are supported.
- Protocol : Pelco Coaxitron
Miscellaneous Functions
HLC(High Light Compensation), SENS-UP, FLIP
(H/V-REV), D-ZOOM, SHARPNESS and PRIVACY
functions are provided.
DAY&NIGHT(ICR)
This camera has a function that automatically
selects the mode that is appropriate for daytime
or night-time conditions.
The COLOR mode operates in daytime
conditions to provide optimum colors, and B/W
mode operates in night-time conditions to
enhance the definition of the image.
• Specification……………………………………………………………………… 32
• Dimension………………………………………………………………………… 33
For images with high contrast between bright
and dark areas from difficult lighting
conditions such as backlighting, this camera
selectively illuminates darker areas while
retaining the same light level for brighter
areas to even out the overall brightness.
Motion Detection
OSD
The camera’s OSD is complimented by 18 languages.
- NTSC : Korean, English, French, Spanish, Japanese,
Portuguese, Taiwanese
- PAL : English, Chinese, German, Italian, French,
Spanish, Russian, Czech, Polish, Romanian,
Serbian, Swedish, Danish, Turkish, Portuguese
Since the camera detects motion without any
additional external sensor, you can monitor
activity more efficient.
COLOR DOME CAMERA
4
User Guide
COLOR DOME CAMERA
5
User Guide
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin’s will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Separate the power plug during a thunder storm.
* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or
personal injuries by robbery, fire, natural disaster or other such events.
May lower image quality.
alarm shop
Warning/Attention/Special Mark Messages
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
Do not install under unstable
lighting conditions.
Avoid touching the camera lens.
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates “Never Allowed.”
Indicates “No Disassembling.”
Severe lighting changes or flickering may hinder
normal camera operation.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Do not drop the camera or subject
it to physical shock.
May cause a product malfunction.
COLOR DOME CAMERA
6
User Guide
Never keep the camera face to
strong light directly.
May damage the CCD.
COLOR DOME CAMERA
7
User Guide
Overview
Precautions
Do not expose the camera to
radioactivity.
9
Do not expose the camera to rain
or other types of liquids.
❶
4 2
3
8
If exposed to radioactivity, the CCD will fail.
5
May cause a product malfunction.Wipe dry any
liquids. Liquids may contain minerals that are
corrosive to electronic components.
alarm shop
Notes
• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.
• Ensure that the power source complies with normal specifications before supplying it to
the camera.
Components and Accessories
❶
2
3
6
7
❶ Pan Base : Control panning angle of camera.
2R
otate Base : Control rotating angle of camera.
3x
3.6 Vari-focal Lens Module 2.8 ~ 10.0mm (F1.2)
4 Video Output Terminal to Monitor
5 Function
Setup switch : D
isplay the menu on the screen and move the cursor to four
directions to confirm status or after changing a selected item.
6
7
8
9
Video Output Jack
Power
Input Terminal
Dome
Cover
Shield Case
Installation
4
❶ SCD-2080
2 Instruction Manual
3 M4 Tapping Screw 3EA
4 Installation Video Output Cable
COLOR DOME CAMERA
8
User Guide
Notes
• The installation should be done by qualified service personnel or sysytem installers.
• If the ceiling material is not strong enough to hold the installation screws, the camera
may fall off. Reinforce the ceiling as needed.
COLOR DOME CAMERA
9
User Guide
Installation
Installation
1) Separate the dome cover by turning anti-clockwise.
2) Separate the shield case by pulling from the camera body.
When using the Ceiling bracket
* To install the dome cover on the camera
body, turn the latches in locking direction
as shown in the figure 1.
Latch
Ceiling bracket
An arrow for installing
directions
Locking direction
[Figure1]
Main Body
(Camera)
M4 tapping
screw (provided)
alarm shop
CAMERA
Shield Case
Unlocking direction
(Anti-clockwise)
1) Hold the ceiling bracket (located where the arrow
points to) and separate it from the main body of
the camera by rotating it anti-clockwise.
(refer to the picture in 'Notes' on page 10)
2) Place the separated ceiling bracket so that the
“Front” side faces the area to be monitored and
install it with the M4 tapping screws.
3) To combine the main body with the ceiling bracket,
make sure that the pan base fixation screw face the
opposite side of the “Front” side of the ceiling
bracket and rotate it clockwise.
4) Adjust the camera lens to face the area to be
monitored and fix the main body and the dome
cover by aligning the grooves and rotating the
body clockwise.
Locking
direction
Locking direction
(Clockwise)
Unlocking
direction
Dome cover
Dome cover
Notes
• The installation should be done by qualified
service personnel or system installers.
• If the ceiling material is not strong enough to
hold the installation screws, the camera may
fall off. Reinforce the ceiling as needed.
• To change the position of the cable, take
away the Hole Cover and pass the cable
through.
COLOR DOME CAMERA
10 User Guide
Original position of
the cable
Hole Cover
Pan Base
fixation
screw
M4 tapping
screw
[Figure-2]
Notes
• If you want to install the camera with the ceiling bracket combined, fix it using two M4 tapping
screws at the side of the main body (refer to the [Figure-2] on page 11).
COLOR DOME CAMERA
11 User Guide
Connection
Installation
Connecting to Monitor
Adjust the panning and tilting, rotating while watching the monitor
Connect the Video Output jack to the VIDEO-IN jack of monitor.
73˚
174˚
176˚
CCTV Camera
Rotate Base
Tilt Base
Monitor
• As the connecting method varies with the instruments, refer to the manual supplied with the
instrument.
• If necessary, you can connect the monitor to the REMOTE jack on the back of your camera.
• Only connect the cable when the power is turned off.
Pan Base
alarm shop
Connecting to Power
1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.
• Pan Base moves by 176˚ to each side direction and 352˚ on the whole.
• Tilt Base covers total 73˚ angle(0˚ ~ 73˚).
• Rotate Base moves by 174° to each side direction and 348° on the whole.
Connect the adaptor to the power input terminal as shown in the figure below. The
recommended adaptor specification for SCD-2080N/SCD-2080P is DC 12V / 500mA or AC 24V
/ 300mA.
---- Power Input Terminal
2) Methods of adjustment
• The case of wall installation
1A
fter mounting the camera on a wall, adjusting the panning angle so that the camera can
face the direction to monitor when tilted.
2 Adjust the tilting angle by rotating the tilt base.
3 Loosen the rotate base hold screw and adjust rotate base for the best view.
4 Tighten the rotate base hold screw.
• The case of ceiling installation
1A
fter mounting the camera on a ceiling, adjusting the panning angle to the correct viewing
position by rotating the pan base.
2 Adjust the tilting angle by rotating the tilt base.
3 Loosen the rotate base hold screw and adjust rotate base for the best view.
4 Tighten the rotate base hold screw.
COLOR DOME CAMERA
12 User Guide
When the resistance value of copper wire is at [20˚C(68˚F)]
Copper wire size (AWG)
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
Resistance (Ω/m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
• As shown in the table above, voltage decreases as the wire gets longer. Therefore
use of an excessively long adaptor output line for connection to the camera may
affect the performance of the camera.
*Standard voltage for camera operation : DC 12V ± 10%, AC 24V ±10%
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
COLOR DOME CAMERA
13 User Guide
Operating Your Camera
Connection
Menu Configuration
Notes
• Be sure to connect power only after all the installation is complete.
• Note that AC / DC adaptor is not supplied with camera.
• Ground should be connected to the GND terminal.
MAIN SETUP
Using Coaxial Communications
CAMERA
SET
UP
DOWN
LEFT
RIGHT
• Coaxial Communications System
• OSD Control method
DVR
MENU/ENTER
UP KEY
DOWN KEY
LEFT KEY
RIGHT KEY
CONTROLLER
OSD KEY
JOYSTICK UP
JOYSTICK DOWN
JOYSTICK LEFT
JOYSTICK RIGHT
●DC
EXPOSURE
●BRIGHTNESS
●SENS-UP
●SHUTTER ●AGC ●RETURN
WHITE BAL
●ATW
●MANUAL
●OUTDOOR
●AWC→SET
alarm shop
DVR
DVD
LENS
• : BNC
• ----: RS-485
• Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial
cable, shown below : If the distance between the camera and the monitor
exceeds the recommended maximum, please use an auxiliary video amp.
Distance
300m
450m
600m
SSDR
●OFF
●ON
BACKLIGHT
●OFF
●BLC
SSNR3
●OFF
●ON
DAY/NIGHT
●COLOR
●B/W
SPECIAL
●IMAGE ADJ
●SYNC
●DIS ●MONITOR
●CAM TITLE
●MOTION DET ●PRIVACY ●LANGUAGE
●RETURN
EXIT
●SAVE
●NOT SAVE
Recommended Cable Specification
3C2V(RG-59/U)
5C2V(RG-6/U)
7C2V(RG-11/U)
Notes
• It is recommended that pure copper coax cable is used and not copper coated
steel, as this will cause issues with the communication over the coaxial cable.
COLOR DOME CAMERA
14 User Guide
●INDOOR
COLOR DOME CAMERA
15 User Guide
●HLC
●AUTO
●RESET
Operating Your Camera
Menu Setup
Notes
Use the Function Setup switch within the camera.
• An item with the icon also has sub menus. To select a sub menu, select an item with
the icon and press the Function Setup switch.
• An item with the - - - icon is unavailable due to function settings.
LENS
Function Setup switch
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select‘LENS’
by using the Function
Setup switch so that the arrow indicates‘LENS’
.
alarm shop
MAIN SETUP
1.LENS DC
2.EXPOSURE 1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
Select the function using
the Function Setup switch.
MAIN SETUP
1.LENS
DC
2.EXPOSURE 3.WHITE BAL
ATW
4.SSDR OFF
5.BACKLIGHT
OFF
6.SSNR3
ON
7.DAY/NIGHT
AUTO
8.SPECIAL
9.EXIT
SAVE
Change the status using
the Function Setup switch.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
COLOR DOME CAMERA
16 User Guide
2. The Lens mode has sub menu site as listed below.
- BRIGHTNESS: Adjusts the video brightness.
- FOCUS ADJ : To adjust the lens focus correctly, you must activate the Focus Settings
mode. To activate the Focus Settings mode, adjust the lens focus, and then deactivate
the settings mode.
- You can adjust the shutter value of ESC shutter mode.
EXPOSURE
MAIN SETUP
1.LENS DC
2.EXPOSURE 3.WHITE BAL ATW
1. When the SETUP menu screen is displayed, select 'EXPOSURE’ by using the Function
Setup switch so that the arrow indicates 'EXPOSURE’.
2. Select a desired mode using the Function Setup switch.
BRIGHTNESS
: Adjusts the video brightness.
COLOR DOME CAMERA
17 User Guide
Operating Your Camera
EXPOSURE SETUP
1.BRIGHTNESS
25
2.SHUTTER
--3.AGC
HIGH
4.SENS-UP
OFF
5.RETURN
SHUTTER
: You can select the shutter.
- A.FLK : Select this when you experience picture flicker, this happens when there
is a clash with the installed lighting frequency.
- ESC : Select this to control the shutter speed automatically. If ESC is selected,
the shutter speed is automatically controlled depending on the ambient
illumination of the subject.
- MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
- ---
: Shutter speed is fixed at 1/60sec(1/50sec).
Notes
RETURN : Select this to save the changes in the EXPOSURE menu and return to the
SETUP menu.
alarm shop
• Set the shutter mode to --- if color rolling occurs.
• When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the
picture may become unstable if the camera faces a bright fluorescent light. Therefore,
take care when choosing the installation position.
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
AGC(AUTO GAIN CONTROL) : T he higher the gain level, the brighter the screen - but
the greater the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
- HIGH : Allows automatic gain control from 5.3dB to 37dB.
Notes
• If you set the Function Setup switch to ‘AUTO’ mode, You can adjust the brightness by
increasing or decreasing the shutter speed. (x2 ~ x512)
• Note that the higher the zoom level, the brighter the screen, but the more likely it is that an
after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the
zoom level is increased, this is normal.
SENS-UP : When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO: Activates the SENS-UP function.
COLOR DOME CAMERA
18 User Guide
White Bal (White Balance)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function
Setup switch so that the arrow indicates ‘White Bal’ .
2. Select a desired mode using the Function Setup switch.
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
4.SSDR DC
ATW
OFF
※ Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,700˚K and
11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
INDOOR : Select this when the color temperature is between 4,500˚K and
8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance
first by using the ATW or AWC mode. After that switch to MANUAL
mode, fine-tune the White Balance and the Function Setup switch.
COLOR DOME CAMERA
19 User Guide
Operating Your Camera
AWC →SET : To find the optimal luminance level for the current environment, point
the camera towards a sheet of white paper and press the Function
Setup switch. If the environment changes, readjust it.
Notes
• White Balance may not work properly under the following conditions. In this case select
the AWC mode.
❶ When the color temperature of the environment surrounding the subject is out of the
control range (e.g. clear sky or sunset).
2 When the ambient illumination of the subject is dim.
3 If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
SSDR ON
SSDR OFF
alarm shop
BACKLIGHT
SSDR (Samsung Super Dynamic Range)
SSDR illuminates darker areas of an image while retaining the same light level for brighter
areas to even out the overall brightness of images with high contrast between bright and
dark areas.
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
4.SSDR 5.BACKLIGHT
DC
ATW
OFF
OFF
1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the Function Setup
switch so that the arrow indicates ‘SSDR’.
2. U
se the Function Setup switch to change the SSDR level in the sub menu according to
the contrast between bright and dark areas.
COLOR DOME CAMERA
20 User Guide
Unlike conventional cameras, the SCD-2080 is designed so that it delivers a distinctive
subject and background at the same time, even when the subject is in backlight, by
adopting a function of the proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates ‘BACKLIGHT’.
MAIN SETUP
1.LENS DC
2.EXPOSURE 3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
2. S elect a desired mode using the Function Setup switch depending on the camera purpose.
BLC : Enables
a user to select a desired area on a picture and view that area more clearly.
- LEVEL : Adjust level of the BLC function.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.
COLOR DOME CAMERA
21 User Guide
Operating Your Camera
HLC (High Light Compensation) : If the scene contains extremely bright light areas such as; from car headlight, the
light can mask out much of the on-screen detail.
- LEVEL : Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / brightness of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.
SSNR3
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ‘SSNR3’ by using the Function Setup
switch so that the arrow indicates ‘SSNR3’ .
OFF : Not being used
MAIN SETUP
1.LENS DC
2.EXPOSURE 3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
alarm shop
3. S elect a desired mode using the Function Setup switch.
Select ‘BLC’ to adjust the area to be
HLC : E nable the user to change the level,
enhanced then adjust the level.
limit, mask color/tone and area.
2. Select a desired mode using the Function Setup switch.
OFF: Deactivates SSNR3. Noise is not reduced.
ON : Activates SSNR3 so that noise is reduced.
3. Set the SSNR3 mode to ‘ON’ and press the Function Setup switch. Then you can adjust
the noise reduction level.
Notes
Notes
• Because there can be a difference in the effectiveness of HLC according to the amount of
light area in the screen, optimize the installation angle for the best HLC performance.
• When dark, the HLC is only activated when a bright light exceeding a specific size. (In
NIGHT ONLY mode.)
• The HLC is not activated in day light or when bright light is not present at night. (In NIGHT
ONLY mode.)
• When HLC function is used, D-ZOOM and DIS functions are not activated.
COLOR DOME CAMERA
22 User Guide
• You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is
‘OFF’.
• When adjusting the noise reduction level in the SSNR3 mode, remember that the higher
the level set, the more the noise level will be reduced, as will the brightness of the image.
COLOR DOME CAMERA
23 User Guide
Operating Your Camera
DAY/NIGHT
You can display pictures in color or in black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function
Setup switch so that the arrow indicates ‘DAY/NIGHT’.
MAIN SETUP
1.LENS DC
2.EXPOSURE 3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
8.SPECIAL
Color ➞ B/W
B/W ➞ Color
2.5 lux
1 lux
5 lux
10 lux
Early
Late
* The day/night switching point of the
camera can be adjusted.
Notes
• When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as selecting 'COLOR'
mode and 'AUTO' mode cannot be selected.
alarm shop
2. S elect a desired mode using the Function Setup switch according to the picture display
you want.
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
You can turn on or off the burst signal on B/W mode.
AUTO : The mode is switched to ’Color‘ in a normal environment, but switches to
’B/W‘ mode when ambient illumination is
low. To set up the switching time for AUTO
mode, press the Function Setup switch.
You can turn on or off the burst signal on
B/W mode.
- DURATION : You can select the day/night switching
point.
- DWELL TIME : You can select the duration time about changing the day/night mode. …
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
COLOR DOME CAMERA
24 User Guide
SPECIAL
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup
switch so that the arrow indicates ‘SPECIAL’.
MAIN SETUP
1.LENS DC
2.EXPOSURE 3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
8.SPECIAL COLOR DOME CAMERA
25 User Guide
Operating Your Camera
2. Select a desired mode using the Function Setup switch.
1.
2.
3.
4.
5.
6.
7.
8.
9.
SPECIAL
IMAGE ADJ
MONITOR
LCD
CAM TITLE
OFF
SYNC
INT
MOTION DET
OFF
PRIVACY
OFF
DIS
OFF
LANGUAGE
ENGLISH
RETURN
• SHARPNESS : As you increase this value, the picture outline becomes stronger and
clearer. Adjust this value appropriately depending on the sharpness of
the picture.
• RETURN
: Select this to save the settings for the IMAGE ADJ menu and to return
to the SPECIAL menu.
Notes
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
• If you increase the SHARPNESS level too high, the picture may become distorted or
noise may appear.
alarm shop
IMAGE ADJ :
1) W
hen the SPECIAL menu screen is displayed, select ‘IMAGE ADJ’ by using the
Function Setup switch so that the arrow indicates ’IMAGE ADJ‘.
2) Select a desired mode using the Function Setup switch.
1.
2.
3.
4.
5.
6.
IMAGE SETUP
V-REV
OFF
H-REV
OFF
D-ZOOM
OFF
FONT COLOR
WHITE
SHARPNESS
ON
RETURN
• V-REV
: You can flip the picture vertically on the screen.
• H-REV : You can flip the picture horizontally on the screen.
• D-ZOOM : You can use a digital zoom of x1 ~ x16.
• FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)
COLOR DOME CAMERA
26 User Guide
Monitor : Please change the settings value of video
appropriate to your monitor.
- LCD : Please select this menu item when using an
LCD monitor.
You can change the gamma, PED level and
color gain in the sub menus.
- CRT : Please select this menu item when using a CRT
monitor.
- USER: Please use this menu item when using a monitor other than standard ones. You
can change the gamma, PED level, and color gain in the sub menus.
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the
arrow indicates ‘CAM TITLE’.
2) Set it to ‘ON’ by using the Function Setup
switch.
3) Press the Function Setup switch.
4) Use the Function Setup switch to move
to a desired letter and select the letter by
pressing the Function Setup switch.
Repeat this to enter multiple letters. You
can enter up to 15 letters.
COLOR DOME CAMERA
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→CLR POS END
27 User Guide
Operating Your Camera
5) Enter
a title, move the cursor to ‘POS’ and press
the Function Setup switch. The entered title
appears on the screen. Select the position to
display the title on the screen by using the
Function Setup switch and press the Function
Setup switch. When the position is determined,
select ‘END’ and press the Function Setup
switch to return to the SPECIAL menu.
FRONT DOOR
Notes
• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even
if you enter one.
• Only English is available in this mode.
• If you move the cursor to CLR and press the Function Setup switch, all the letters are
deleted. To edit a letter, change the cursor to the bottom left arrow and press the
Function Setup switch. Move the cursor over the letter to be edited, move the cursor to
the letter to be inserted and then press the Function Setup switch.
MOTION DET :
T his product has a feature that allows you to observe
movement of objects in 8 different areas on the
screen, and the words 'MOTION DETECTED' appear
on the screen when movement is detected. You can
monitor activity more efficient.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates‘MOTION DET’
.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS: Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILL→SET : Fills in a selected MD area. The color of filling is sequentially selected as
brown, orange, blue, cyan, green, yellow, magenta and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the
SPECIAL menu.
alarm shop
SYNC : In areas where the supply is at 60Hz(NTSC),
50Hz(PAL), you can synchronize the output
phase of multiple cameras using the power
synchronization function (Line-Lock) without
using a synchronization signal generator.
- INT : Internal Synchronization Type - L/L : Power Synchronization Type, Line-lock • Press the Function Setup switch.
• Y
ou can select a desired phase from 0 to 359 when select 'phase'.
Notes
• When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L
type synchronization.
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
COLOR DOME CAMERA
28 User Guide
PRIVACY :Mask an area you want to hide on the screen.
1.
2.
3.
4.
5.
6.
7.
8.
9.
PRIVACY AREA SETUP
AREA
AREA1
MODE
OFF
MASK COLOR
GREEN
MASK TONE
1
TOP
39
BOTTOM
79
LEFT
13
RIGHT
52
RETURN
COLOR DOME CAMERA
29 User Guide
Operating Your Camera
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so
that the arrow indicates ‘PRIVACY’.
2) Set up the mode using the Function Setup switch.
- AREA
: You can select up to 12 PRIVACY areas.
- MODE
: Determines whether to use the area selected in the AREA.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White,
Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the
SPECIAL menu.
DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to
external factors such as wind.
Notes
• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
LANGUAGE : You can select the menu language according to your requirements.
- NTSC: Korean, English, French, Spanish, Japanese, Portuguese, Taiwanese
- PAL : English, Chinese, German, Italian, French, Spanish, Russian, Czech, Polish,
Romanian, Serbian, Swedish, Danish, Turkish, Portuguese
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
• Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are
properly connected.
▶ Check that you have properly connected BNC cable to the camera.
•
The image on the screen is dim.
▶ Is the lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to the proper condition.
▶ If the camera is exposed to very strong light, change the camera position.
• The image on the screen is dark.
▶ Adjust the contrast feature of the monitor.
▶ If you have an intermediate device, set the 75Ω / Hi-z properly.
alarm shop
• As the DIS function uses the digital zoom, the camera's resolution will decrease.
• DIS doesn’t operate when background illumination is too low.
Troubleshooting
RETURN : S elect this to save the SPECIAL menu settings and return to the MAIN SETUP
menu.
EXIT
Select a desired EXIT mode using the Function Setup switch depending on the camera
purpose.
- SAVE
: Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language and Monitor
settings are not initialized.
COLOR DOME CAMERA
30 User Guide
• T he camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
• The SENS-UP function does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
• The Motion Detection function does not work.
▶ Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
• Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu.
• The screen flickers continually.
▶ Check that direction of camera turns toward the Sun.
• When coaxial communication is not available:
▶ Make sure that the camera and monitor are installed within the recommended distance.
▶ Use the video amplifier equivalent to coaxitron if the recommended installation distance
is exceeded.
COLOR DOME CAMERA
31 User Guide
Dimension
Specifications
SCD-2080N
Min. Illumination
S/N (Y Signal)
Video Output
LENS
Zoom Ratio
Focus Length
Angular Field of View
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range
OPERATIONAL
Electronic Shutter Speed
ON Screen Display
SSDR
Backlight Compensation
Day & Night
Gain Control
White Balance
SENS-UP (frame Integration)
Motion Detection
Privacy Masking
3D Noise Filter (SSNRIII)
Digital Zoom
Digital Image Stabilization(DIS)
Camera Title
Sharpness
Flip / Mirror
Communication
ENVIRONMENTAL
Operating Temperature / Humidity
Storage Temperature / Humidity
MECHANICAL
Dimension / Weight
SCD-2080P
Ø115.8
DC 12V / AC 24V
Max 3.5W
1/3 inch, Diagonal 6mm Super HAD CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
2:1 Interlace
Internal / Line-Lock
H : 15.734KHz V:59.94Hz
H: 15.625KHz V: 50.00Hz
COLOR : 600TVL, B/W : 700TVL
COLOR : 0.15 Lux (50IRE, @F1.2), 0.0003Lux (SENS-UP, x512)
B/W : 0.001Lux (50IRE, @F1.2), 0.000002Lux (SENS-UP, x512)
52dB (Weight On, AGC Off)
CVBS : 1.0Vp-p, 75Ω composite
alarm shop
3.6x (Manual)
2.8 ~ 10.0mm (F1.2)
Tele : 28°(H) x 21°(V), Wide : 94.4°(H) x 69.2°(V)
0°~352° / 0°~73° / 0°~348°
1/60 ~ 1/120k sec
1/50 ~ 1/120k sec
NTSC : Korean, English, Japanese, Spanish, French, Portuguese, Taiwanese
PAL : English, Chinese, German, Italian, French, Spanish, Russian, Czech, Polish,
Romanian, Serbian, Swedish, Danish, Turkish, Portuguese
On / Off (Level adjustable)
BLC / HLC / OFF
COLOR / BW / AUTO (ICR Type)
Low / High / Off
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable zones)
On / Off (12 Programmable zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Displayed 15 Characters)
On / Off (Level adjustable)
On / Off
Coaxial(Pelco Coaxitron)
Ø97
92.7
ELECTRICAL
Input Voltage
Power Consumption
VIDEO
Imaging Device
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
Horizontal Resolution
-10°C ~ +50°C / 30% ~ 80% RH
-20°C ~ +60°C / 20% ~ 90% RH
Ø115.8 x 92.7(H)mm / 345g
※ The specification for this product may change without prior notice for product improvement.
COLOR DOME CAMERA
32 User Guide
COLOR DOME CAMERA
33 User Guide
DECLARATION OF CONFORMITY
Application of Council Directive(s)
2004 / 108 / EC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
MEMO
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SCD-2080P
alarm shop
Beginning Serial NO. C5CZ6V3Z200001X
Year of Manufacture 2010.02.01
Conformance to EN 55022 : 2006
EN 50130-4 : 2003
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name BONJENG GU
Full Name
Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA
Place
Date 2010.02.01
Date
COLOR DOME CAMERA
34 User Guide
COLOR DOME CAMERA
35 User Guide
alarm shop
SALES NETWORK
•
AMSUNG TECHWIN CO., LTD.
S
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
AMSUNG TECHWIN EUROPE LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungsecurity.com
P/No. : Z6806-1138-01A
VAN 10. 02
Download PDF
Similar pages