Network Set-up and Operation For Macintosh PLC

Owner’s Manual
Network Set-up and Operation
For Macintosh
Wired and Wireless Setting
Projector Set-up and Operation
Network Capture
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic operation of the
projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.
Compliance
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Model Number : QXXAVC922---P
Trade Name : Sanyo
Responsible party : SANYO FISHER COMPANY
Address : 21605 Plummer Street, Chatsworth, California 91311
Telephone No. : (818)998-7322
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the
following two conditions: (1) the device may not cause interference, and (2) the device must accept any
interference, including interference that may cause undesired operation of this device.
CAUTION: P
roperly shielded a grounded cables and connectors must be used for connection to host
computer and /or peripherals in order to meet FCC emission limits.
VGA cable with ferrite core must be used for RF interference suppression.
For Canadian Users
This Class B digital apparatus complies with Canadian ICES-003.
Cet apparei numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC RF Exposure Warning
- This transmitter must be co-located or operated in conjunction with any other antenna or transmitter.
- This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and
meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment
must be installed and operated with at least 20cm and more between the radiator and person’s body
(excluding extremities: hands, wrists, feet and ankles).
The CE Mark is a Directive conformity mark of the
European Community (EC).
English
Česky
[Czech]
Dansk
[Danish]
Deutsch
[German]
Eesti
[Estonian]
Español
[Spanish]
Ελληνική
[Greek]
Français
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvių
[Lithuanian]
Nederlands
[Dutch]
Malti
[Maltese]
Magyar
[Hungarian]
Polski
[Polish]
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
Svenska
[Swedish]
Islenska
[Icelandic]
Norsk
[Norwegian]
The Alert Mark is a Directive conformity mark of the
European Community.
Hereby, SANYO Electric Co., Ltd., declares that this WLAN Module (QXXAVC922---P) is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
SANYO Electric Co., Ltd. tímto prohlašuje, že tento WLAN Module (QXXAVC922---P) je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede SANYO Electric Co., Ltd. erklærer herved, at følgende udstyr WLAN Module
(QXXAVC922---P) overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt SANYO Electric Co., Ltd., dass sich das Gerät WLAN Module (QXXAVC922---P) in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 1999/5/EG befindet.
Käesolevaga kinnitab SANYO Electric Co., Ltd. seadme WLAN Module (QXXAVC922---P) vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
Por medio de la presente SANYO Electric Co., Ltd. declara que el WLAN Module (QXXAVC922---P)
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ SANYO Electric Co., Ltd. ΔΗΛΩΝΕΙ ΟΤΙ WLAN Module (QXXAVC922- - -P)
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Par la présente SANYO Electric Co., Ltd. déclare que l’appareil WLAN Module (QXXAVC922---P) est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Con la presente SANYO Electric Co., Ltd. dichiara che questo WLAN Module (QXXAVC922---P) è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo SANYO Electric Co., Ltd., deklarē, ka WLAN Module (QXXAVC922---P) atbilst Direktīvas 1999/5/
EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Šiuo SANYO Electric Co., Ltd.deklaruoja, kad šis WLAN Module (QXXAVC922---P) atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hierbij verklaart SANYO Electric Co., Ltd. dat het toestel WLAN Module (QXXAVC922---P) in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/
EG.
Hawnhekk, SANYO Electric Co., Ltd., jiddikjara li dan WLAN Module (QXXAVC922---P) jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Alulírott, SANYO Electric Co., Ltd. nyilatkozom, hogy a WLAN Module (QXXAVC922---P) megfelel a
vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym SANYO Electric Co., Ltd. oświadcza, że WLAN Module (QXXAVC922---P) jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
SANYO Electric Co., Ltd. declara que este (QXXAVC922---P) está conforme com os requisitos
essenciais e outras disposições da Directiva 1999/5/CE.
SANYO Electric Co., Ltd. izjavlja, da je ta (QXXAVC922---P) v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
SANYO Electric Co., Ltd. týmto vyhlasuje, že (QXXAVC922---P) spĺňa základné požiadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
SANYO Electric Co., Ltd. vakuuttaa täten että (QXXAVC922---P) tyyppinen laite on direktiivin 1999/5/
EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar SANYO Electric Co., Ltd. att denna (QXXAVC922---P) står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Hér með lýsir SANYO Electric Co., Ltd. yfir því að (QXXAVC922---P) er í samræmi við grunnkröfur og
aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
SANYO Electric Co., Ltd. erklærer herved at utstyret (QXXAVC922---P) er i samsvar med de
grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Safety instructions
CAUTION IN USING THE PROJECTOR VIA NETWORKS
● When you find a problem with the projector, remove the power cable immediately and inspect
the unit. Using the projector with failure may cause fire or other accidents.
● If you remotely use the projector via networks, carry out a safety check regularly and take
particular care to its environment. Incorrect installation may cause fire or other accidents.
CAUTION IN USING NETWORK FUNCTION
● SANYO Electric Co., Ltd. assumes no responsibility for the loss or damage of data, or damage of
the computer caused by using this projector. Making back-up copies of valuable data in your
computer is recommended.
Caution about Radio Wave
This unit operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical
equipment (such as pacemaker), as well as amateur radio stations.
Please read “Safety Instructions” section and make sure the following cautions.
1. Be sure that there are no other devices in the area that may use the same frequency band as
Projector.
2. If any other devices are causing radio interferences, change the communication frequency channel
or move to other location.
Trademarks and Copyright
- Macintosh is a registered trademark of Apple, Inc. in the USA and other countries.
- PowerPC is a registered trademark of IBM Corporation.
- Intel Core is a registered trademark of Intel Corporation in the USA and other countries.
- O ther company names, product names or other names noted in this manual are trademarks or
registered trademarks of the respective companies. Note that ® and TM marks are not indicated in the
text of this manual.
Notes
- The contents of this manual are subject to change without notice.
- You may not copy the printed materials accompanying with the software.
- We shall not be responsible for any damages caused by reliance on this manual.
Expression/Abbreviation
The OS of the computer and the Web browser described in this manual is MAC OS X v10.4 and Safari
3. In case of another OS or Web browser, some instruction procedures may differ from the actual
operation depending on your computer environment.
Use of this manual
This manual does not provide the description of basic operation and functions for computer, web
browser, projector and network. For instructions about each piece of equipment or application
software, please refer to the respective booklet.
Table of contents
Compliance..........................................................................................................................................................2
Safety instructions.............................................................................................................................................4
Table of contents................................................................................................................................................5
Operating environment and configuration..............................................................................................7
Required operating environment for computers...............................................................................7
Network specifications of the projector.................................................................................................8
1. About LAN functions.....................................................9
LAN functions and the features.................................................................................................................10
Image projecting system via LAN.............................................................................................................10
An example of the connection..................................................................................................................11
LAN connection modes................................................................................................................................12
2. Setup procedures..........................................................15
Installing the software..................................................................................................................................17
3. N
ames and functions of the operation screen............21
Network connection standby display.....................................................................................................22
Network Capture 5 window........................................................................................................................23
4. Wired LAN configurations............................................25
Connecting to the LAN line........................................................................................................................26
Network environment settings.................................................................................................................26
Confirming the operation............................................................................................................................28
Network PIN code...........................................................................................................................................30
Network information.....................................................................................................................................30
Wired factory default....................................................................................................................................30
Wired LAN factory default settings..........................................................................................................31
5. Wireless LAN configurations........................................33
Setting the network environment............................................................................................................34
Setting procedures........................................................................................................................................34
Configuring security with the projector.................................................................................................36
Network PIN code...........................................................................................................................................39
Network information.....................................................................................................................................39
Wireless factory default................................................................................................................................39
WIRELESS indicator display.........................................................................................................................40
Wireless LAN factory default settings.....................................................................................................41
6. Basic setting and operation..........................................43
Starting up the Browser...............................................................................................................................44
How to use the setting page......................................................................................................................46
Initial setting.....................................................................................................................................................48
Network configuration.................................................................................................................................51
Configuring wireless LAN setting and security setting....................................................................53
E-mail setting...................................................................................................................................................55
SNMP setting....................................................................................................................................................59
7. Controlling the projector.............................................63
Power control and status check................................................................................................................64
Controls..............................................................................................................................................................66
PC adjustment.................................................................................................................................................70
Setting up the projector...............................................................................................................................71
Timer setting....................................................................................................................................................74
Projector information....................................................................................................................................77
Multi-control....................................................................................................................................................79
8. Network capture functions..........................................85
About Network Capture function.............................................................................................................86
Using the Real Time Capture......................................................................................................................89
Error information............................................................................................................................................94
9. Appendix........................................................................95
Use of telnet.....................................................................................................................................................96
Web browser setting.....................................................................................................................................98
Firewall setting for MAC OS X v 10.4........................................................................................................101
Firewall setting for MAC OS X v 10.5........................................................................................................102
Troubleshooting.............................................................................................................................................103
Terminology.....................................................................................................................................................106
Operating environment and configuration
Required operating environment for computers
When operating the projector via the networks, computers should meet the operating environment
below.
MAC OS X v 10.4 or later
OS
800 MHz PowerPC G4 or faster,
or 1.8 GHz Intel Core processor or faster
CPU
Memory
Free HDD Space
Screen Resolution
Communication Protocol
Network
Correspond
Wireless LAN
Wired LAN
Browser Application
256MB or more (512MB is recommended)
100MB
Required to support any of VGA (640 x 480), SVGA
(800 x 600), XGA (1024 x 768),
The color number should be either 16 bit (65536
colors) or 24/32 bit (16.77 million colors).
TCP/IP
Correspond to IEEE802.11b/g
Correspond to 100BASE-TX (100Mbpd)
/10BASE-T (10Mbps)
Safari 3.0 or later
Network specifications of the projector
LAN Terminal
Data communication speed
100Base-TX (100Mbps)/10Base-T (10Mbps)
Protocol
TCP/IP
Interface
IEEE802.11b/g
Communication Mode
AdHoc,
Infrastructure
Wireless LAN
Data Transfer Speed
Wireless Frequency (Channel)
Modulation Form
1/2/5.5/11Mbps (IEEE802.11b)
6/9/12/18/24/36/48/54Mbps (IEEE802.11g)
2412MHz–2462MHz (CH1–CH11)
IEEE802.11g OFDM
54/4Mbps 64QAM, 36/24Mbps 16QAM, 18/12Mbps
QRSK, 9/6Mbps BPSK
IEEE802.11b DSSS
11/5Mbps CCK, 2Mbps DQPSK, 1Mbps DBPSK
Protocol
TCP/IP
Security
WEP 64Bit (Open/Shared) /WEP 128Bit (Open/Shared),
WPA-PSK(TKIP), WPA2-PSK(AES),
SSID, ESSID
Service area
about 30 m (without disturbance)
Differs according to the operating environment.
Compliance
JAPAN: VCCI ClassB,TELEC (Wireless)
Countries and Standards
USA: FCC Part15 Subpart C (Wireless)
FCC Part15 Subpart C, Class B
Canada: IC RSS-210 (Wireless), IC ICES-003 ClassB
Europe: R&TTE, EMC, LVD
Chapter
1
1. About LAN functions
This chapter describes the features, the mechanism,
and connection procedures of the LAN.
Chapter 1 About LAN functions
LAN functions and the features
This product is loaded with a LAN network function which enables you to project an image on the
computer through a projector via Network with dedicated software.
With the software, you can also manipulate the projecting image and the projector.
This software has functions below and you can use the projector under various network environments
to meet the wide-ranging needs of the operation.
• Accept both Wired and Wireless LAN environment. When the projector is operated via Wireless LAN,
there is no need for wire connection.
• One computer image can be projected up to 5 projectors simultaneously.
• Network capture function to project the computer's screen image through the projector.
• Remote function which allows you to operate the projector from a distance.
• Monitoring function for the projector operation.
• E-mail function which reports the operating status to your maintenance management.
• Multi control function which can operate multiple projectors (up to 100) simultaneously.
Image projecting system via LAN
The images are projected through an image capturing system which helps to project the faithful
computer images. With this system, you can use the product under various application environments
despite the differences of application software.
Flow of Image Transfer
1. Download the computer image with the dedicated software faithfully to the real image.
2. The downloaded data will be compressed to the digital signal and transferred to the projector via the
LAN (Wired or Wireless). (One computer can operate up to 5 projectors simultaneously.)
3. Digital signal will be reproduced into RGB image signal and will be projected by the projector.
✳ The image will be transferred to each projector. The time lag can occur between each projection.
CAUTION: This product does not correspond to the application with DirectX, MSOffice assistant, and video replay such as DVD.
10
An example of the connection
An example of the connection
The illustration below shows an example of the projection via the LAN.
You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN
connection) through the selected projector .
2.0
1.5
1.0
0.5
0.0
2.0
1.5
1.0
0.5
0.0
2.0
1.5
1.0
0.5
0.0
Computer (1)
Access point
Computer (2)
11
Chapter 1 About LAN functions
LAN connection modes
Connection modes differ depending on the LAN and computer environments.
Connect appropriately for each environment.
■ Wireless LAN, Infrastructure Communication Mode
Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or,
communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment
will select an access point to communicate SSID/ESSID modes. These communication modes are used
when both Wireless LAN and Wired LAN are used in the same network environment.
Computer (1) Computer (2)
Access point
Wireless communication mode
corresponded computer: Infrastructure
■ Wireless LAN, AdHoc Communication Mode
Communication mode between Wireless LAN equipment.
(Communication mode via SSID/ESSID)
Network Projector
Wireless communication mode :AdHoc
Wireless communication mode corresponded
computer: AdHoc
12
LAN connection modes
■ Wired LAN Communication Mode
Communicate via the LAN line.
Computer(1)
Computer(2)
Computer (3)
✳ Operate the computer mouse with the remote control.
When the projector’s remote control employs mouse operating function, you can operate
the computer by the remote control which is provided with the projector. To use the remote
control, point to the projector. You do not need to connect the USB cable to operate the
computer mouse.
(For details about the remote control operation, refer to the owner’s manual of the projector.)
13
Chapter 1 About LAN functions
14
Chapter
2
2. Setup procedures
This chapter describes how to install the Network
Capture 5 software and how to set up the networks.
15
Chapter 2 Setup procedures
To use the projector via the networks, follow the setup procedures below.
STEP 1
Install the software on computers.
Install the software recorded in CD-ROM on each computer which will be operated.
Read following pages of this chapter to install.
STEP 2
Select Wired LAN or Wireless LAN then connect the
LAN and set the configuration.
Decide depending on the LAN environment.
Wired LAN............. Refer to “4. Wired LAN Configurations” (pp.25–31).
Wireless LAN........ Refer to “5. Wireless LAN Configurations” (pp.33–42).
Detailed LAN configurations need to be done with a browser later.
First, complete the Wired or Wireless LAN connection between computers and
projectors, then start browser configurations.
➔ “6. Basic setting and operation” (pp.43–62).
STEP 3
Network Configuration has completed.
Follow each chapter to project an image and operate the projector.
■ Operate and manage the projector ➔ “7. Controlling the projector” (pp.63-84)
➔ “Projector Power status and check” (p.64)
➔ “Controls” (p.66)
➔ “PC adjustment” (p.70)
➔ “Setting up the projector” (p.71)
➔ “Timer setting” (p.74)
➔ “Projector information” (p.77)
➔ “Multi-control” (p.79)
■ Project an image on the computer ➔ “8. Network capture functions" (pp.85-94)
➔ “Use of real time capture” (p.89)
16
Installing the software
Installing the software
It is required to install the software into your computer to use the Network Capture function . Please
install the software as follows.
Note: To install the software into the computer, logon as an administrator. Before installation,
make sure that the other applications are closed, otherwise proper installation cannot
be made.
Network Capture 5 installation
1 Set the supplied Network Capture 5 CD-ROM into the CD-ROM drive of your computer. Double click
Network Capture 5.pkg.
2 Click Continue on the introduction screen.
3 As the "License Agreement" will appear, read contents carefully, click Continue button and click
Agree if you agree on the next screen to the license agreement to proceed with installing.
17
Chapter 2 Setup procedures
4 Select a Destination, and Click Continue.
5 Click Install to perform a basic installation.
6 Click Close to complete the installation.
18
Installing the software
Installed software
The following software is installed on your computer.
● Network Capture 5:
Captures the displayed image of the computer and serves it to the projector via the network.
* Move to Trash to uninstall this software.
19
Chapter 2 Setup procedures
20
Chapter
3
3. Names and functions of the operation
screen
This chapter describes the functions of each part of the
operation screen.
21
Chapter 3 Names and functions of the operating screen
Network connection standby display
Turn on the projector and select either “Wired” or “Wireless” from the input menu of the projector.
The “Please wait...” message will be displayed on the screen. After short time, the network connection
standby display screen will appear as below. While the “Please wait...” message is shown, you cannot
operate the projector.
Network Connection Standby Display
22
Network Capture 5 window
Network Capture 5 window
This software is to project the computer screen via the networks.
Click "Network Capture 5" from "Macintosh HD" --> "Application" -->"Network Capture 5" menu, then
following screen will appear. Then the program will start.
e
r
t
y
u
q
w
i
Parts Names and Functions of the Screen
q Search PJ button
Search the projector connected to the networks.
w Specify IP button
When connected to a different segment network, the projector can not be retrieved automatically.
In that case, press this button, and then, the "Search specified IP address" window appears, and
enter the IP address directly to specify the projector.
e Network Projector List
Display all the projectors connected to the networks.
Show unoccupied projector as “On standby” and occupied projector as “Real time capturing” or "In
One-shot mode". The indication of the status of use with "#" indicates that your computer is now
using the network capture function.
After double-clicking on a projector, the web browser gets activated and the projector setup screen
will be displayed.
23
Chapter 3 Names and functions of the operating screen
r Start real time capture button
Capture (Project) the computer screen in real time. After the execution of "Start real time capture",
the application window disappears.
t One-shot capture button
Copy and capture (project) the computer screen without modification. After the execution of Oneshot capture, the application window disappears.
y Terminate capture button
Terminate the real time capture and the One-shot capture.
u Select capturing object button
It is possible to designate the window to capture individually. This button is disabled by default,
so the full screen is captured. It is possible to change the capturing object function setting at
parameter settings. For detail, refer to "Parameter set up" (p.88).
i Parameter setup button
Activate the parameter setup window, and execute the connections setting and the image setting.
For detail, refer to "Parameter set up" (p.88).
Using the multiple network adaptors
When your computer provides multiple network adaptors, the network adaptor selecting window will
appear each time the Network Capture 5 software starts. Select a network adaptor and check the "Select
a network adaptor as default" and then click OK. To change the setting, refer to the item "Parameter set
up" (p.88).
24
Chapter
4
4. Wired LAN configurations
This chapter describes the preparation for Wired
LAN setting with projectors and how to set the LAN
environment.
25
Chapter 4 Wired LAN configurations
Setting procedures and contents differ depending on the LAN installation location.
When installing, consult your system administrator to set up the LAN appropriately.
Connecting to the LAN line
Connect the LAN cable to the LAN connection terminal of the projector.
LINK/ACT Lamp (Orange)
Light or blink orange when
the projector is connected
to the network.
LAN Connection
Terminal
SD
LAN Cable
Speed Lamp (Green)
Light according to the
speed of the connected
network.
10 Base-T.........Off
100 Base-T.......On
* When the LAN setting is “Off”, the two lamps
will not be on.
Network environment settings
Set the Wired LAN network through the projector menu.
Detailed network settings will be made with browser. Refer to “6. Basic setting and operation” (p43-62).
First, complete the settings described in this chapter before performing steps in “6. Basic setting and
operation.”
Setting Procedure
1. Turn on the projector and select “Wired” from the input menu of the projector.
The projector’s LINK/ACT Lamp will be on or blink. If the “Wired setting” is “Off”, it will not on. Follow
step 2 and 3 to blink the lamp.
2. Select “Wired Setting” in the projector menu, and press SELECT button.
Select similar LAN environment among LAN1, 2 and 3 with the Point 7 8 buttons. (LAN1, 2, and
3 are the factory default setting environments. You can select three different environment among
setting LAN1–3. For each setting, refer to the chart on page 31.)
When selecting “Off” in the “Wired setting”, the LAN connection will be cut off. Use the function when
disconnecting the projector from the network.
3. Press the Point 7 8 buttons then the “Please wait...” message will appear and switching operation
will start. Switching will take a while and after completing the operation, the “Ready for use” message
will appear. During the switching period, the projector cannot be operated.
26
26
Network environment setting
4. Press SELECT button.
LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the
setting environment. Consult your system administrator about the detailed settings.
Adjust the figures with the Point ed buttons and move among the items with the Point 7 8
buttons.
5. After completing all the settings, select “Set” and press SELECT button. Now, all procedures have been
done. To cancel the adjusted settings, select "Cancel" and press SELECT button.
To confirm whether the settings are correct, follow the procedures described from the next page.
You can confirm the LAN settings you have made from “Network Information” (p.30). In such cases
that the LAN cannot be connected, see this screen.
Wired setting
Network PIN code
Wired LAN setting screen (Example)
Item
Description
DHCP...........................Sets DHCP function On or Off. When you setup the network setting manually, select "Off".
When it is set On, IP address, Subnet, Gateway and DNS are automatically set according to your
network environment *1.
IP address..................Sets IP address of the projector
Subnet........................Sets Subnet mask. Normally sets 255.255.255.0
Gateway*2. ................Sets IP address of the default gateway (Router)
DNS*2..........................Sets IP address of the DNS server.
*1 Set "On" only when the DHCP server is available on your network environment.
*2 Set [255.255.255.255] if the network does not provide the gateway (router).
*3 Set [255.255.255.255] if you do not use the function E-mail alert.
27
Chapter 4 Wired LAN configurations
Confirming the operation
Confirm that the projector has connected to the LAN properly.
1. Activate “Network Capture 5” which is installed into the computer connected to the LAN .
2. After “Searching projector” message appears, the name of the projector* appears on the Network
Projector List, then the network setting has completed properly.
When the name of the projector does not appear and error screen appears, the network has
not connected yet. Try searching again with the Search PJ button. If error screen appears again,
reconfirm the LAN setting. When the projector is set in the location separated by the router, see next
page.
When Firewall function (Anti-virus software) is effective, network projector may not be found. In that
case, disable the Firewall function and try searching again.
✳ If the projector is named, the name will be displayed. The name can be set with the following
procedures in “6. Basic setting and operation” ➔ “Initial setting” (p48) . If the projector is not named,
IP address of the projector will be displayed.
Network Capture screen
Network Projector List
Search PJ button
28
Confirming the operation
When set up the projector in the location separated by the router and the segment is different;
Projector will not be found nor displayed. In that case, the projector needs to be searched directly by
the IP address.
1. Press Specify IP button. The window below appears.
2. Enter the IP address of projector and Click OK. Then, the projector will be added on the Network
Projector List of the application window.
Network Projector list
Specify IP button
The window above appears.
29
Chapter 4 Wired LAN configurations
Network PIN code
The Network PIN code is to restrict the access from the networks to the projector.
After setting the Network PIN code, you need to enter it to operate the projector via the networks.
1. Select Network PIN code menu, and press SELECT button.
The Network PIN code screen will appear.
2. Set the Network PIN code.
Set the figures with the Point ed buttons and move to the next items with the Point 7 8 buttons.
Select “Set” and press SELECT button to set. To cancel the preset Network PIN code, select “Cancel”.
When you do not want to set the Network PIN code, set "0000".
It is recommended to set the Network PIN code if you use the projector via the networks. The Network
PIN code can be set also through the networks. See “6. Basic setting and operation” ➔ “Initial setting”
➔ “Network PIN code setting” (p49).
Network PIN code
Network PIN code screen
Network information
Wired factory default
Network information
(See the menu above.)
Select Network information from the projector menu and press SELECT button to show LAN setting
environment of the currently selected projector. (The description below is an example and different
from what will be shown.)
Network information
MAIN PROGRAM: V1.000
MAC ADDRESS:
08007B650056
IP ADDRESS:
172.21.95.202
Wired factory default
30
(See the menu above.)
Select “Wired factory default” from the projector menu and press SELECT button. All the wired LAN
settings will go back to the factory default settings. For details, refer to “Wired LAN factory default settings”
(p.31).
Wired LAN factory default settings
Wired LAN factory default settings
SELECTED LAN
Parameter
LAN1
LAN2
LAN3
IP ADDRESS
169.254.100.100
192.168.100.100
192.168.100.100
SUBNET MASK
255.255.0.0
255.255.255.0
255.255.255.0
GATEWAY ADDRESS
255.255.255.255
255.255.255.255
255.255.255.255
DNS ADDRESS
255.255.255.255
255.255.255.255
255.255.255.255
IP CONFIGURATION
MANUAL
DHCP
MANUAL
31
Chapter 4 Wired LAN configurations
32
Chapter
5
5. Wireless LAN configurations
This chapter describes the preparation for Wireless
LAN setting with projectors and how to set the LAN
environment.
This projector contains the Wireless LAN module.
The setting procedures and configurations differ
depending on the LAN installation location. Consult
your system administrator for installation and set the
LAN appropriately.
To operate via Wireless LAN, your computer has to
be equipped with a Wireless LAN card adapter which
supports IEEE 802.11b/g.
If connecting in Infrastructure mode with an access
point, the access point is required to support IEEE
802.11b/g.
Caution: Do not use a mobile phone or PHS near
(within 20cm/8inch) the projector. It may
cause malfunction.
Note on Macintosh
Easy wireless setting function cannot be used with
Macintosh.
33
Chapter 5 Wireless LAN configurations
Setting the network environment
The projector contains the Wireless LAN adapter.
Set the Wireless LAN network through the projector menu.
Detailed network settings will be made with browser. Refer to “6. Basic setting and operation”. ➔"Network
configuration" (p.51). Complete the settings described in this chapter before performing the steps in “6.
Basic setting and operation.”
Setting procedures
1. Turn on the projector and select “Wireless” from the input menu of the projector. The “Please wait...”
message will be displayed on the screen. After short time, the network connection standby display
screen will appear. Refer to “3. Names and Functions of the Operation Screen” (p.21).
2. Select “Wireless Setting” from the projector menu and press SELECT button.
Select similar environment between LAN 4 and LAN 5 with the Point 7 8 buttons. (LAN 4 and LAN 5
are factory default settings. Select similar environment to the installation location. For each settings,
refer to "Wireless LAN factory default settings" on page 42.)
3. Press the Point button then the “Please wait...” message will appear and switching operation will start.
Switching will take a while and after completing the operation the message will disappear. During
the switching period, the projector cannot be operated.
Wireless setting
Network PIN code
Network Information
Wireless factory default
34
Setting the network environment
4. Press SELECT button. LAN setting screen will appear and the selected LAN settings will be displayed.
Adjust each item to the setting environment. Consult your system administrator for the detailed
settings.
Adjust the figures with the Point ed buttons and move among the items with the Point 7 8
buttons. When the network type is “AdHoc”, you do not have to change “Sub net” and “Gateway” and
leave them as default settings.
SSID/ESSID for the network type “Infrastructure” and “AdHoc” are required to be entered the same
characters into the projector, the access point, and the Wireless LAN compatible computer (up to 32
characters). Characters can be selected from A~Z, a~z, blank (space), 0–9, or - (hyphen) with the Point
ed buttons. Move to the next character with the Point 7 8 buttons.
You can confirm that the projector settings from “Network Information” in the projector menu (p.40).
5. A
fter completing all the settings, select “Set” and press SELECT button. Now, all procedures have
been done. To cancel the adjusted settings, select the "Cancel" and press SELECT button.
To confirm whether the settings are correct, follow the procedures in “4. Wired LAN configurations”
➔ “Confirming the Operation” (p.28).
For configuring of WEP, WPA-PSK,
WPA2-PSK security, select “Next”. Refer
to “Configuring security with the
projector” on next page for details.
Item
Description
DHCP...........................Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When
its set On, IP address, Subnet, Gateway and DNS are automatically set according to your network
environment *1.
IP address..................Sets IP address of the projector
Subnet........................Sets Subnet mask. Normally sets 255.255.255.0
Gateway*2. ................Sets IP address of the default gateway (Router)
DNS*2..........................Sets IP address of the DNS server. Must be set when the E-mail function is used.
Network type...........Sets Infrastructure or AdHoc mode. When the "AdHoc" is selected, the security "WPA-PSK" and
"WPA2-PSK" are not available.
SSID/ESSID....................Identifier of the wireless access point.
*1 Set "On" only when the DHCP server is available on your network environment.
*2 Set [255.255.255.255] if the network does not provide the gateway (router).
*3 Set [255.255.255.255] if you do not use the function E-mail alert.
35
Chapter 5 Wireless LAN configurations
Configuring security with the projector
Configure security with the projector by following the steps below.
After configuring the network in “5. Wireless LAN Configurations” (p.33-42), select “Next” in the LAN
setting screen and press SELECT button. The security configuration screen appears. Refer to “6. Basic
setting and operation” ➔ “Configuring wireless LAN setting and security setting” (p.53) as well.
WEP configuration screen
Use the Point ed buttons to select the security type. To disable the security, select “Disable.”
Use the Point 7 8 buttons to move among the items; use the Point ed buttons to adjust settings.
This projector provides the following security options. Use optimum security option on your network
environment.
WEP64(40)bit Open
WEP64(40)bit Share
WEP128(104)bit Open
WEP128(104)bit Share
WPA-PSK(TKIP)
WPA2-PSK(AES)
Notes when entering characters:
The “¥” symbol is displayed as “\” when the ASCII key is used. The “]” symbol is treated as a character
by the ASCII key, but it is not interpreted as a character by the HEX key. In HEX, the “]” symbol is
displayed in red and setting is denied.
You can not set all the characters with the “]” symbol. This will be considered as no operation.
ASCII key characters : Space - 0 to 9 A to Z a to z ! " # $ % & ' ( ) * + , . / : ; < = > ? @ [ ¥ ] ^ _ ` { | } ~
HEX key characters : 0 to 9 a to f
36
Configuring security with the projector
Use of security type "WEP"
1. Use the Point ed buttons to select "WEP" security type.
2. Select “WEP Key index”. Use the Point ed buttons to choose the HEX or ASCII key. The four (#1–#4)
kinds of WEP keys can be configured. Use the Point 7 8 buttons to move to the right frame; use the
Point ed buttons to select a WEP key number (#1–#4).
Refer the table below for the usable number of characters at the WEP security option.
WEP option
Characters
WEP64(40)bit ASCII
WEP64(40)bit HEX
WEP128(104)bit ASCII
WEP128(104)bit HEX
5 characters
10 characters
13 characters
26 characters
WEP configuration screen
3. Use the Point 7 8 buttons to select the Type field of the WEP key number that corresponds to the
one you selected above and press SELECT button. The WEP key entry screen appears. In the WEP key
entry field, all characters are displayed in “]”. Use the Point ed buttons to select a character; use the
Point 7 8 buttons to select a character position. Enter all the characters displayed with “✳”.
When you select HEX at WEP key index and the entry key contains “]”, the “]” symbol is displayed in
red and setting is denied.
4. Use the Point 7 8 buttons to select “Set” and press SELECT button to return to the Wireless setting
screen. Select “Set” in the Wireless setting screen to complete the network setting.
37
Chapter 5 Wireless LAN configurations
Use of security type "WPA-PSK", "WPA2-PSK"
1. Use the Point ed buttons to select "WPA-PSK" security type. WEP security setting fields are grayed
out.
WPA-PSK configuration screen
2. Select “Next” and press SELECT button. The PSK key confirmation screen appears.
3. Use the Point 7 8 buttons to select the key field and press SELECT button. The PSK key entry screen
appears. Enter the PSK key by using the Point buttons. If the input PSK key has an error, the PSK key is
indicated in red.
Available PSK key characters
ASCII code.......8 to 63 digits
Hex code..........64 digits
4. Use the Point 7 8 buttons to select “Set” and press SELECT button to return to the PSK confirmation
screen. Select “Set” and press SELECT button to complete the PSK key setting and the Wireless
setting screen appears. Select “Set” and press SELECT button to complete the network configuration.
38
* Security "WPA-PSK" and "WPA2-PSK" modes are not available when the "AdHoc" network type is selected.
* When you set the PSK keys with 64 digits, the projector checks whether all of the entered PSK keys are in Hex code or
not. If any of the ASCII code is included in the entered PSK keys, the entered PSK keys are indicated in red as error.
Network PIN code
Network PIN code
The Network PIN code is to restrict the access from the networks to the projector.
After setting the Network PIN code, you need to enter it to operate the projector via the networks.
Select “Network PIN code” from the projector menu and press SELECT button. Set with the same
procedures as setting Wired LAN Network PIN code. Refer to “4. Wired LAN Configurations” ➔ “Network
PIN code” (p.30).
Network information
Display the current LAN connecting environment. Select “Network Information” from the projector
menu and press SELECT button.
Wireless Information (Example)
Network information
MAIN PROGRAM:
V1.000
MAC ADDRESS:
08007B650056
IP ADDRESS:
169.254.53.0
WIRELESS MODE:
802.11b
NETWORK TYPE:
AdHoc
CHANNEL:
11
SSID/ESSID:
WIRELESS
Wireless factory default
Select “Wireless factory default” from the projector menu (p.34) and press SELECT button. All the
wireless LAN settings will go back to the factory default settings. For details, refer to “Wireless LAN
factory default settings” (p.41).
39
Chapter 5 Wireless LAN configurations
WIRELESS indicator display
WIRELESS indicator display
When the wireless LAN configuration is set up correctly and the wireless communication is established
with the access-point or the computer in the network, the WIRELESS indicator on the front panel lights
up. While the projector scans the equipment in the network, the WIRELESS indicator blinks.
WIRELESS indicator
40
Wireless LAN factory default settings
Factory default settings for LAN4 and LAN5 as follows.
Selected LAN
Setting Items
LAN4
LAN5
169.254.100.100
192.168.100.100
255.255.0.0
255.255.255.0
255.255.255.255
255.255.255.255
DNS ADDRESS
255.255.255.255
255.255.255.255
IP CONFIGURATION
MANUAL
DHCP
WIRELESS CHANNEL
11
11
NETWORK TYPE
802.11b AdHoc
INFRASTRUCTURE
WIRELESS SSID/ESSID
(SSID/ESSID)
PJ-WIRELESS5
ANY
WEP
(WEP encryption)
DISABLE
DISABLE
WPA-PSK
(PSK key)
DISABLE
DISABLE
WPA2-PSK
(PSK key)
DISABLE
DISABLE
IP ADDRESS
SUBNETMASK
GATEWAY ADDRESS
41
Chapter 5 Wireless LAN configurations
42
Chapter
6
6. Basic setting and operation
Describes basic operation and settings below by using
the web browser.
• Initial setting
Setup the basic setting such as Projector
name, Network PIN code, Time setting, etc.
• Network setting
Configure Wired/Wireless LAN environment.
• E-mail Setting
Configure E-mail function to manage the
projector.
• SNMP Setting
Configure SNMP function to manage the
projector.
Caution: When operating the projector with the browser,
connect the projector to the computer with Wired or
Wireless LAN. Complete the connection in advance.
43
Chapter 6 Basic setting and operation
Starting up the Browser
1. Turn on the projector.
2. Start up the Network Capture 5. The Network Capture 5 searches projectors in the network and lists
up the IP address or projector name of the projector on the Network Projector List.
3. Double click the projector to set from the Network Projector List.
4. The web browser will start up and display the setting page of the projector.
Select a display mode and login
T his product provides 2 types of control mode, Standard Mode and Light Mode as below. Select
a proper mode to match your PC and network environment by clicking on the text link. Once you
select your desired display mode, the setting page you selected display mode will be displayed
automatically from the next login. To change the display mode, click "Top" on lower-right corner of
the setting page (p.45).
STANDARD MODEFor computer display, displays graphical
m e n u s a n d s e t t i n g s. Th i s m o d e i s
recommended for standard use.
LIGHT MODEDisplays with 200 x 300 dots. This mode
is optimized for use of the handheld
computer, PDA, etc. It is also convenient
if the network traffic is heavy. (This mode
has some limitations on the multi-control
functions.)
I f the password has been set on the setting page, the
authentication window will appear. In that case, type
"user" onto the User Name text area and the login
Network PIN code onto the Password text area and then
click Log in button.
* The entered User Name must be "user" and it can not be changed.
[Note]
When the projector is accessed for the first time or the Network PIN code "0000" is set, the auto-login is performed
and the next main setting page is displayed.
44
Starting up the browser
Display of main setting page
The following main setting page will be displayed depending on your display mode selection.
Perform various kinds of settings through this page. Click on the menus to display the control and
setting pages.
z Main setting page in the Standard Mode display
Clock display
Display on or off by
clicking text ON or OFF
Sub menu tab
Switches the sub
menu tab.
Page numbers
Switches the pages by
clicking the number's
tab.
Main menu
Setting page
For selection of control and
setting items of the projector.
Displays the control and
setting items according to the
selected menu.
R e t u r n s to D i s p l ay
Mode selection page
(☞ p.44)
* To change the screen language, use the initial setting menu (p.48)
✐T
his Standard mode display is mainly used through this manual for the setting and
control description.
✐I f your computer does not have the Adobe Flash
Player version 6 or later, follow the message on the
control page to install the Adobe Flash Player. For
further product information or installing, see the
Adobe homepage.
http://www.adobe.com
45
Chapter 6 Basic setting and operation
x Main setting page in the Light Mode display
Sub menu tab
Page numbers
Returns to the display mode selection
page.
Main menu
Setting page
Returns to main menu
✐ T he blank page appears if your PDA does not provide a Adobe Flash
Player. You need to install the Adobe Flash Player. (☞p.45)
How to use the setting page
To control and set up the projector, use the setting menus on the web browser. The basic operation and
procedures commonly used on this manual are described below.
Example of the Setting Page
The setting pallet appears after clicking the item. Change the
value by clicking s or t button, or type the number onto the
text box directly and then click Set button.
* Each item has a valid setting range respectively.
Setting Pallet
46
✐ T he value in the text box indicates current value.
✐E ach item has a valid setting range. The setting value exceeding its range becomes invalid. Some control items can
not be used depending on the selected input mode or functions of the projector you use. In that case, the values of
those items are indicated with "---".
How to use the setting page
Type of the setting pallet
Text box setting
Enter the number or text and then
click Set button.
or
Change a value with s or t
button and then click Set button.
The value changes quickly when
s or t button is kept pressing.
Pull-down menu setting
Select an item with pull-down
menu button and then click Set
button.
or
Select an item by clicking s or t
button.
Radio button setting
Select an item by selecting a radio
button
Check box setting
Select items by ticking on check
boxes.
47
Chapter 6 Basic setting and operation
Initial setting
After installing the projector, perform the following basic initial setting.
Click Initial Setting on the main menu to display the initial setting page.
Item
Description
Language..................Switches display language on the setting page. English or
Japanese.
Model name.............Indicates the model name of the projector.
Projector name........Sets the name of projector. This projector name is listed on
the application window of the Network Capture software.
Network PIN code............Sets the Network PIN code to login the setting page (+p.30,
p.40)
PJLink..........................Switches PJLink password authentication on or off.
Password...................Password for PJLink function
48
Initial setting
Network PIN code setting
This is to set the Network PIN code to restrict the access from an
unauthorized person through the network.
Enter a 4-digit number as the Network PIN code onto the text box and
click Set button.
The projector's network part begins restarting and it takes about 20
seconds. Close (Quit) the web browser and access to the login page
again in 20 seconds. This is to perform the login authentication firmly.
The default Network PIN code as [0000], which means no Network PIN code is set.
✐ When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a fourdigit number is valid for the Network PIN code.
✐ If you forget the Network PIN code to the projector, you can check it by selecting "Network PIN code" sub menu
from "Network" menu on the projector. For further information, please see item "Network PIN code setting"
(+p.30, p.40).
PJLink and password setting
This is to set the PJLink password authentication on or off. If "On" is set
with the PJLink pull-down menu, the password must be required. Enter
a password* onto the text box and click Set button.
Refer to the projector owner's manual for further details of the PJLink
function.
✐ 1 to 32 alphanumeric characters can be used for the password.
What's PJLink?
The projectors equipped with PJLink function can be used together on the same network, regardless
of model or brand, for centralized control and monitoring. This standard was established by the Japan
Business Machine and Information System Industries Association (JBMIA). http://pjlink.jbmia.or.jp/
49
Chapter 6 Basic setting and operation
Item
Description
NTP address..............Enter the address of NTP server. Please consult your
network administrator for setting up of the NTP server.
Temperature.............Switches display temperature unit Centigrade or
Fahrenheit
Time setting..............When clicking AUTO button, the date and time set on
your computer are set to the projector. The timer icon
appears when time is set up correctly.
Current time.............Indicates current date and time set on the projector
Date.............................Sets date in manual
Time.............................Sets time in manual
Date and time setting
NTP is abbreviated expressions of Network Time Protocol. It is a protocol to acquire the exact current
time via the network. This projector acquires the current time from the NTP server and update the time
in the network module. After setting the NTP address, the projector acquires the time per 24 hours. If
the projector fails acquiring the time from the NTP server, the projector tries to acquire the time every 1
hour until it succeeds.
When the NTP address is not set, perform the time setting with "Auto-setting" or "manual setting"
described below.
Auto setting
Click AUTO button on the page, the date and time set on your computer are set to the projector.
Note:
Confirm that your computer has a correct clock time before performing the auto time setting.
Manual setting
Click the item Date or Time and enter the date or time on the input box
with adequate format.
Date is in year/month/day format.
ex. 2007/10/05
Time is in 24-hour:minute format.
ex. 18:30
50
This projector does not provide the built-in battery. The date and time information are lost when
the projector turns off ( when "Eco" is set for the stand-by mode (Refer to p.72)), or the network
configuration is reset, or the input mode "Wired" or "Wireless" is turned. The timer function is
disable until time is set up correctly. When using the NTP address for time setting, the current time
is acquired at the projector starting up and the timer function is activated after finishing the time
setting correctly.
Network configuration
Network configuration
Click Network on the main menu. The following setting page is displayed. Set up the
projector's network environment on this Setting sub menu.
Setting of LAN
1. Select a type of LAN from Change setting pull down menu.
LAN1(Wired)
LAN2(Wired)
LAN3(Wired)
LAN4(Wireless)
LAN5(Wireless)
For the default setting of the above LAN, see the items "Factory Default Setting".
Item
Description
Change setting........Selects LAN1 to LAN5
IP configuration......Sets DHCP or Manual
IP address..................Sets IP address of the projector
Subnet mask............Sets Subnet mask.
Default gateway*1...........Sets IP address of the default gateway (Router)
DNS*2..........................Sets IP address of the DNS server.
*1 Set [255.255.255.255] if the network does not provide the gateway (router).
*2 Set [255.255.255.255] if you do not use the function E-mail alert.
51
Chapter 6 Basic setting and operation
2. Select either "Manual" or "DHCP" from IP configuration pull
down menu. When "DHCP" is selected, IP address, Subnet
mask, Default Gateway, DNS are automatically configured by
DHCP function. Only the DNS address allows you to set up
manually if the DNS address information is not provided on
your DHCP server. When selecting "Manual", configure all the
items manually. For further information, contact your network
administrator. The address must be entered as 4 number groups
separated by a dot like [192.168.001.101].
3. A fter completing the network configuration, press Regist
button to register the network information.
4. To apply the setting, press Set button. The network of the
projector starts re-booting and applies the setting. It takes
about 20 seconds to complete. Close the web browser and access to the login page again in 20
seconds.
On the screen of the projector, the “Please wait...” message will appear and switching operation will
start. Switching will take a while and after completing the operation, the “Ready for use” message will
appear. During the switching period, the projector cannot be operated.
When you use LAN4(wireless) or LAN5(Wireless), the setting items of page [2] and [3] are activated
and you can setup Wireless LAN setting and Security setting. See the item "Configuring Wireless LAN
Setting and Security Setting" for further setting.
52
Configuring wireless LAN setting and security setting
Configuring wireless LAN setting and security setting
Configure the wireless LAN setting and security setting for LAN4 and LAN5.
Configuring wireless LAN setting
1. Click page [2] of setting pages. Following wireless LAN setting can be done. After completing the
configuration, press Set button.
Item
Description
Wireless Mode.........Select the Communication standard 802.11b or 802.11b/g
Network Type...........Select either “Infrastructure” or “AdHoc”. When selecting the "AdHoc", the security
"WPA-PSK" and "WPA2-PSK" mode are not available.
SSID/ESSID................Set the SSID/ESSID. (up to ASCII 32 characters)
SSID/ESSID is case-sensitive. Even though all characters on the Wireless
information is uppercase, it is necessary to distinguish between upper case and
lower case characters.
Channel......................If you use the projector in 802.11AdHoc mode, select the channel, from 1 to 11.
53
Chapter 6 Basic setting and operation
Configuring wireless LAN security setting
lick page [3] of setting pages. Following wireless LAN security
C
setting can be done. After completing the configuration, press
Set button.
Item
Description
Network security....Sets the type of encryption. Following types are available.
WEP64(40)bit Open
WEP64(40)bit Share
WEP128(104)bit Open
WEP128(104)bit Share
WPA-PSK(TKIP)
WPA2-PSK(AES)
Input type.................ASCII or HEX. See item "Notes for entering characters"
Key index1 - 4..........Enter keys of encryption.
The used number of character changes as the table below according to the type
of WEP encryption and input type.
WEP option
Characters
WEP64(40)bit ASCII
WEP64(40)bit HEX
WEP128(104)bit ASCII
WEP128(104)bit HEX
5 characters
10 characters
13 characters
26 characters
Four key indexes can be set, however, the only one with check on its radio
button is effective. Both of the number and value of the key index in effect must
be same as those of your computer and the access point.
Depending on computers and access points, you may be allowed to select only
one WEP key. In that case, use key index1.
PSK...............................Available when the "WPA-PSK(TKIP)" or "WPA2-PSK(AES)" is selected.
The PSK key must be no fewer than 8, nor more than 63 digits with ASCII code,
and 64 digits with Hex code.
Notes for entering characters:
The “¥” symbol is displayed as “\” when the ASCII key is used. The “]” symbol is treated as a character
by the ASCII key, but it is not interpreted as a character by the HEX key. In HEX, the “]” symbol is
displayed in red and setting is denied.
You can not set all the characters with the “]” symbol. It will be considered as no operation.
ASCII key characters : Space - 0 to 9 A to Z a to z ! " # $ % & ' ( ) * + , . / : ; < = > ? @ [ ¥ ] ^ _ ` { | } ~
HEX key characters : 0 to 9 a to f
54
E-mail setting
E-mail setting
This product has an E-mail function which can send an alert message to users or an
administrator if it detects an abnormality on the projector or run out of the life span
of the lamp. Click E-mail Setting on the main menu and follow the below steps.
Item
Description
SMTP server* . .........Sets server name or IP address of the SMTP server
Administrator
address.......................Sets E-mail address of administrator
Add E-mail
address.......................Sets E-mail address of the user to send a mail when the
projector has an abnormality.
1
1 Setting SMTP server and administrator address
Set the server name or IP address of the SMTP server*1 and administrator address. The administrator
address is set to "Reply-To" address of the message sent from the projector.
*1 The SMTP server is a server for sending E-mail. Please contact your network administrator to have this SMTP
server address. When the server name for SMTP server is used, DNS must be set up to activate the E-mail
function.(+p.51)
✐ I f the projector sends an alert message due to the abnormality on the projector but the SMTP server is down in
some other reason, the message will not be sent. In that case, the message "Unable to connect to server." will be
displayed on the setting page. To clear this message, set up SMTP server address again.
✐ To use the E-mail function, it must be set the DNS address on the Network setting page correctly.
✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment.
55
Chapter 6 Basic setting and operation
2 R egistering and deleting E-mail addresses
Click "Add E-mail address" and type the E-mail address onto the
text box and click Set button. To check the registered addresses,
click Check/Delete sub menu tab. The addresses are listed as the
figure on the right.
✐ Up to 10 E-mail addresses can be registered.
To delete the registered addresses, check the address you want to
delete and click Delete button.
Check / Delete
3O
ption selection for sending alert mail
Click Option sub menu tab. Check the condition items under
which alert mail will be sent and click Set button.
Please refer to the item "Examples :Type and contents of alert
mail" described on the next page.
Option
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When internal PJ power circuit is failed.
o When internal PJ temperature is too high.
o W hen PJ is turned into Standby in proper user
operation.
[2]––––––––––––––––––––––––––––––––––
o When accumulated filter use time reaches
[
] hours.
o W hen Power management function turns PJ
lamp off.
o When the signal is interrupted.
o When Auto Play is failed.
[3]––––––––––––––––––––––––––––––––––
o When lamp Corres. Value reaches
[ ] hours.
Attached message
56
✐T he length of message should be less than 255
characters.
✐ Up to 99,999 hours can be set for use time.
E-mail setting
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the registered E-mail
address depending on your selected condition. Administrator or user can take an efficient action
quickly by receiving this message. This is very useful to maintain and service the projector.
The following are examples of received messages.
● When internal PJ temperature is too high:
TITLE: Message from projector
10-03-2007 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off, because internal Projector temperature is too high.
Wait for the completion of the cooling process and make sure the projector has been
turned into Standby. Then turn the projector on again.
If the Indicator continues flashing, check the air filter for dust accumulation.
[A] 81.5 degrees fahrenheit [B] 134 degrees fahrenheit [C] 95.6 degrees fahrenheit
Temperature of Sensor B is too high.
✐ The projector let users know the information which thermal sensors inside the projector detected the
abnormal temperature risen and so the projector was turned off. Please refer to item "Power control
and status check" (☞ p.64) for the location of the sensors and each temperature . Also see the owner's
manual of the projector for further details.
● When internal PJ power circuit is failed:
TITLE: Message from projector
10-03-2007 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off, because Projector power circuit is failed.
Unplug the Projector from AC outlet and ask servicing to qualified service personnel.
MAIN, ALL OK
FAN,
5V
OK
MCI,
3.3V
NG
Error information
✐ The projector lamp was turned off, because the projector power circuit failed.
Unplug the projector from AC outlet and contact a qualified service personnel for service with the error
information.
57
Chapter 6 Basic setting and operation
● When PJ lamp replacement time is reached:
TITLE: Message from projector
10-03-2007 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The PJ lamp replace time is reached.
✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without
resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This
alert mail will not be sent when the mail sending condition "When the life span of lamp is reached" is
unchecked.
● When lamp corres. value reaches preselect use time:
TITLE: Message from projector
10-03-2007 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The accumulated lamp use time reaches 1800 hours.
Prepare for the lamp replacement.
Discretional messages
✐ T he projector sends a free message when the lamp use time (Corresponding value) reaches the
preselected lamp use time. It can be used for preparation of the lamp replacement and the maintenance
required.
58
SNMP setting
SNMP setting
This product provides a SNMP (Simple Network Management Protocol) agent
function. The SNMP consists of a manager and agents. The group which exchanges
information with SNMP is called "Community". There are two access modes in a
community, Refer (read only) and Set (read- write). This product allows to use Refer (read only) only. The
SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on
the main menu and set up each item.
PJ information
Item
Description
Contact......................Enter user name of the projector etc. (optional)
Place...........................Enter place of the projector (optional)
Community
name(refer)..............Enter community name (read only). Default name is
"public".
✐The SNMP agent provided with this product is based upon MIB-2 defined by RFC1213. For private MIB
information, refer to file "Mibinfo/XUPjNet.mib" in the CD-ROM.
59
Chapter 6 Basic setting and operation
Trap
Item
Description
Community name............Enter community name to send "Trap". Default name is
"public".
Trap address.............Enter IP address of the SNMP manager computer to
receive "Trap". Up to 10 addresses can be registered.
✐ Up to 10 trap addresses can be registered.
Trap check/delete
Check and delete the trap address
Checking the registered trap address and deleting the address.
To delete the address, tick the check box in front of the IP address
and click Delete button.
60
SNMP setting
Trap option
Trap option setting
Tick the check boxes in front of the condition item to send the trap.
✐ Click Set button if you tick or un-tick the check box on a page.
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When internal PJ power circuit is failed.
o When internal PJ temperature is too high.
[2]––––––––––––––––––––––––––––––––––
o W hen PJ is turned into Standby in proper user
operation.
o When accumulated filter use time
reaches [
] hours.
o W hen Power management function turns PJ
lamp off.
[3]––––––––––––––––––––––––––––––––––
o When the signal is interrupted.
o When Auto Play is failed.
o When lamp Corres. Value reaches
[
] hours.
✐ Up to 99,999 hours can be set for the time setting.
61
Chapter 6 Basic setting and operation
62
Chapter
7
7. Controlling the projector
Describes controlling and setting of the projector by
using the web browser.
63
Chapter 7 Controlling the projector
Power control and status check
Click Power & Status on the main menu. The control page will be displayed.
By clicking ON or Standby button on the page, the power of the projector can be
controlled.
Confirmation window as
shown in the below appears
when the Standby button is
pressed.
Popup confirmation window
Item
Description
PJ status
Power . ...........................Displays the status of the lamp. (ON, OFF, On starting up, On cooling down)
Status .............................Displays the status of the projector's power. (Refer to next page.)
Power control...............Controls the projector power by clicking the "ON" or "Standby" button.
PJ temp.
Inside temp.A ..............Displays the surrounding temperature of lamp in the projector.
Inside temp.B ..............Displays the surrounding temperature of panel in the projector.
External temp. . ...........Displays the surrounding temperature of the intake vent.
...........The warning icon will appear if the temperature exceeds a specified value. Check if there
is no object to obstruct the airflow around the intake or exhaust vent. It might be airfilter
clogged. Replace the airfilter with new one.
* The temperature unit can be set either Centigrade or Fahrenheit in the item "Initial
Setting". (+p.50)
64
✐ The projector cannot be turned on while the projector is cooling down.
✐ The web browser checks and updates the projector's condition every 30 seconds automatically.
Power control and status check
About projector condition
Status
Description
Normal...................................................................Projector is operating normally.
Power management in operation.......................Power management is operating
Lamp failure........................................................Lamp failure is occurring
Abnormal Temperature...................................The temperature of the projector became too high
Cooling down after abnormal Temp.Projector detects abnormal temp. and is cooling down itself.
Standby after Abnormal Temp.....................Projector detects abnormal temp. and is set into standby mode.
Power failure ......................................................Power failure has occurred inside the projector. Projector is turned off.
Unplug the AC cord and contact a qualified service personnel for service.
If the power failure occurs on the projector, "Power failure" is indicated on
the status column and the information icon appears on the power column
as shown below. Click this icon to display further information of the power
failure.
Click this icon to display
further information of the
power failure.
When a security (PIN code lock) has been set on the projector, you also cannot control it through
the network. To control the projector through the network, unlock the security on the projector
using with the projector's menu control.
Caution about turning on/off the projector via the networks
When turning on/off the projector via the networks, preset the projector as follows:
1. Select “Setting” from the Projector menu.
2. Select “Standby mode” from the Setting menu and set it as “Normal”.
If you set this function as Normal, the network part of the projector is constantly provided with
power even if the projector is turned off. If you set this as Eco, then the network part will be turned
off when you turn off the projector. Consequently, you cannot turn on/off the projector via the
networks.
65
Chapter 7 Controlling the projector
Controls
Click Control on the main menu. The setting method differs depending on the
contents of the page. Click on the page number to change pages and select desired
setting items.
✐ Please see the owner's manual of the projector to have the further
information of each control item.
Input
This function is to select the input mode and source mode of the projector. Click Set button after
selecting the input and source mode.
Item
Description
Input............................Selects input mode of the projector.
Source.........................Selects signal source of the input.
Computer1 : RGB(PC analog)
RGB(PC digital)
RGB(AV HDCP)
Computer2 :
RGB
Component
RGB(Scart)
Video :
Auto
Video
S-video
Network: Wired
Wireless
66
✐ The control page displays valid control items depending on the selected input mode, signal or functions of the
projector you use, therefore, there may be different controls between the described items and actual control items
on the page display. For further information , refer to the projector's owner's manual.
✐ When the projector is standby, only the timer on the setting menu is available; others are not available.
Controls
System
This function is to select the system of signal input to the projector. The available system modes are
listed on the pull-down menu button according to the input signal. Select a system and then click Set
button.
Available selection at the RGB(PC analog) input
Item
Description
XGA1...........................It automatically switches to the proper computer
system of the input signal.
* The computer system modes (VGA, SVGA, XGA. SXGA,
UXGA, WXGA...) which meet the input signal listed.
Available selection at the RGB(PC digital) input
Item
Description
D-XGA.........................It automatically switches to the proper computer
system of the input signal.
* The computer system modes (D-VGA, D-SVGA, D-XGA.
D-SXGA1...) which meet the input signal listed.
Available selection at the Video/S-video/Scart input
Item
Description
AUTO...........................It automatically switches to the proper color system of
the input signal.
* The selectable color systems are PAL, SECAM, NTSC,
NTSC4.43, PAL-M and PAL-N.
* AUTO is fixed at the Scart input.
Available selection at the RGB(AV HDCP) input
Item
Description
AUTO...........................It automatically switches to the proper scanning system
of the input signal.
* The selectable scanning systems are D-480p, D-575p,
D-720p, D-1035i and D-1080i.
Available selection at the Component input
Item
Description
AUTO...........................It automatically switches to the proper scanning system
of the input signal.
* The selectable scanning systems are 480i, 575i, 480p,
575p, 720p, 1035i and 1080i.
✐ I f the modes (Mode1 to Mode5) stored in the item "PC Adjustment" (☞ p.70) are available, they are also listed
together with the above mode.
67
Chapter 7 Controlling the projector
Image adjustment
This function is to adjust the projected picture image and save the image mode. To store the adjusted
value, click Store button, and to load the adjusted value, click Load button.
Item
Description
Contrast.....................Adjusts picture contrast
Brightness.................Adjusts picture brightness
Color............................Adjusts picture color saturation
Tint...............................Adjusts picture hue
Item
Description
Color temp................Sets a color temperature mode.
White balance
Red, Green,
Blue.......................Adjusts each white balance respectively.
Sharpness..................Adjusts picture sharpness.
* When the value of the white balance is changed, the color temp. indicates
"Adj."
Item
Description
Gamma......................... Adjusts brightness of darker part of the picture.
Noise reduction........­Switches noise reduction mode
Progressive...................­Switches progressive mode
Reset............................Resets the Image adjustment to previous levels.
Store............................Stores the Image adjustment values. Select an item
[Image 1 - Image 4] from the pull-down menu and click
Store button.
Load.............................Loads the Image mode.
Select an image mode from
the pull-down menu and
click Load button. There may not be available mode
depending on the input
mode as shown in the table
left.
Input source
Image mode
Video
4
Dynamic
Standard
4
Real
*
Cinema
4
Blackboard(Green)4
Image 1 - 4 4
68
Computer
4
4
4
*
4
4
✐ The mark "4" indicates the available image mode in the selected input
source. The error message appears when the disabled image mode
indicated with "*" is selected.
Controls
Sound
This function is to adjust the sound of the projector. The values in the text box represent the current
control value or status.
Item
Description
Volume.......................Adjusts the sound volume from the speakers.
Mute............................Suppresses the sound.
69
Chapter 7 Controlling the projector
PC adjustment
Click PC Adj. on the main menu. This function is to adjust the signal from the
computer connected to the projector to obtain the proper picture image on the
screen.
Item
Description
Current mode............Displays a current mode like VGA, SVGA, XGA, SXGA, UXGA,
WXGA, etc. or MODE1 - MODE5 are the customized mode
created by using the "Mode Store" function described below.
Auto PC adj...............Performs automatic adjustment.
Fine sync....................Performs Fine Sync adjustment.
Total dots...................Adjust the number of total dots in the horizontal period.
Clamp.........................Adjusts the phase of the clamp.
Display area
Horizontal................Adjusts the image area horizontally.
Vertical..................Adjusts the image area vertically.
Item
Description
Position
Horizontal............Adjusts the horizontal position of the screen.
Vertical..................Adjusts the vertical position of the screen.
Reset............................Resets the PC adjustments to the previous levels.
Mode Store...............Stores the PC adjustment values. Select a mode no.
[Mode1 - Mode5] from the pull-down menu.
Mode Free.................Clear the PC adjustment values. Select a mode no.
[Mode1 - Mode5] from the pull-down menu.
70
Setting up the projector
Setting up the projector
Click Setting on the main menu. This function is to set up the projector. Select the
sub menu [Screen setting], [Setting 1] or , [Setting 2] and then set up each setting.
Item
Description
Screen.........................Switches the screen mode. There may not be available
mode depending on the input mode as shown in the
table below.
Input source
Screen mode
Normal
True
Wide
Full Custom
Video
Computer
4
*
4
*
4
4
4
4
4
4
✐ The mark "4" indicates the available screen mode in the selected input
source system. The error message appears when the disabled screen mode
indicated with "*" is selected.
71
Chapter 7 Controlling the projector
Item
Description
Language..................Sets the language display of projector's on-screen
display menu.
Auto setup................Executes the Auto PC Adj, and Auto Keystone function
below according to the each setting after clicking Start
button.
Auto PC Adj.........Sets Auto PC Adjustment mode.
Auto Keystone....Sets Auto Keystone mode.
Blue back...................Sets the blue screen background when no signal input.
Display........................Switches on or off the on-screen menu display on the
screen.
Countdown off..... Displays image during the starting up.
Item
Description
Logo............................Sets the logo display on the screen during the startup.
Ceiling.........................Sets the image top/bottom and left/right reversed.
Rear..............................Sets the image left/right reversed.
Input search..............Sets the auto-input signal detection mode.
Standby mode.........Sets the network function enable or disable in the
standby mode.
Normal......Enable
Eco.............Disable
No show.....................Sets the black out image temporarily.
Item
Description
Freeze.........................Sets the image to freeze mode.
Power
management...........Sets into the selected power management mode if the
input signal is interrupted and no control key is pressed
for the specified period of time.
*The specified time can be set 1 to 30 min.
On start......................Sets the power-on mode when the AC cord is
connected to the outlet.
Lamp control............Selects lamp control mode.
Pointer........................Sets the pointer form.
Remote control...........Sets the remote control code.
72
Setting up the projector
Item
Description
Key lock......................Sets the prohibition of controls either Projector or
Remote control.
Fan...............................Sets the cooling options after turning off.
L1 Normal cooling
L2 Silent cooling
Fan control...............Sets the fan control speed.
On1 Normal mode
On2 Highland mode
On3 Upward projection mode
Item
Description
Lamp counter..........Displays the lamp use time (Corresponding value) .
Reset the time after the lamp is replaced.
Lamp counter resetting
1. Select a Lamp radio button and then click Reset button.
2. Click OK button to execute the reset.
Filter counter............Displays the filter use time. Reset the time after filter
replaced.
Filter warning...........Sets the time to indicate the filter replacement message
on the screen.
Item
Description
Factory default................. Sets all of the projector control items to the factory
default setting except the following items.
Lamp Corres. Value, PJ time, Filter time.
P-TIMER......................Switches the P-TIMER display.
ON........... Starts P-TIMER indication
STOP....... Stops P-TIMER counting
OFF......... Stops P-TIMER indication
73
Chapter 7 Controlling the projector
Timer setting
This page is to set the timer to turn the projector off or on at a programmed day/date
and time. Follow the steps below for setting.
Click Timer on the main menu.
"---" will appear on the current time when the time is
not set up correctly.
Present time set on the
projector
Select date
Select day
Set execute time
Event
action
How to set the timer
1 Set a day or date
To set the timer event at the same time everyday or every week,
select day entry with radio button and then select desired day from the pull-down menu button.
The selectable days are as follows:
- Same time everyday
- Every week (days from Monday to Sunday)
To set the timer event on specified date,
select date entry with radio button and then type the date with (Year/Month/Date) format.
74
Ex.: Type [2007/12/20] if you specify [December 20, 2007].
This projector does not provide the built-in battery. The date and time information are lost when
the projector turns off (when "Eco" is set for the stand-by mode (Refer to p.72)), or the network
configuration is reset, or the input mode "Wired" or "Wireless" is turned. The timer function is disabled
until time is set up correctly. When using the NTP address for time setting, the current time is acquired
at the projector starting up and the timer function is activated after finishing the time setting
correctly.
Timer setting
2 Set an execute time
Type the time with (Hour:Minute) and 24 hours format.
Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes].
3 Select an event action
Select an event action from the pull-down menu.
Event
Action
ON................................... Turns on the projector
OFF................................. Turns off the projector
Lamp Auto................... Changes lamp mode to "Auto"
Lamp High................... Changes lamp mode to "High"
Lamp Normal.............. Changes lamp mode to "Normal"
Lamp Eco...................... Changes lamp mode to "Eco"
4 Register an event
Click Set button to register the set timer event. Repeat steps 1 to 4 for another timer event setting.
Check the timer events
To check the set timer events, click Check button. The timer
events are listed. The event with blue background color
represents the timer-OFF event.
Change the event mode
On the event list appearing by clicking Check button, click on the
event you want to delete, disable or enable. Click Cancel, Delete,
Timer ON or Timer OFF button on the popup pallet.
Button
Operation
Cancel.........................Cancels the setting
Delete.........................Deletes the timer event
Timer OFF..................Disable the timer event temporarily
Timer ON...................Enable the timer event
75
Chapter 7 Controlling the projector
Notes on timer setting
✐U
p to 10 timer events can be registered. Timer events always operate according to the next valid event depending
on the projector's power status. In the example below, event 3 turns on the projector so next event 4 (also turning
on projector) will not be effective because the projector is already turned on. Similarly, when the projector is
turned off by event 5, event 6 OFF will not be effective in turning it off again. But these secondary events (event 4
and event 6) will become effective if a person turns off the projector (after event 3 and before event 4) or turns on
the projector (after event 5 and before event 6).
Invalid event
Projector Power
Event 1
Event 2
Event 3
Event 4
Event 5
Event 6
ON
OFF
Invalid event
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
Time
✐ When the timer events are set at the same time, the last event set will override the previous events. For example,
if there is an event like "ON at 8:00 everyday" and then new event is set like "OFF at 8:00 everyday", only the last
setting event is effective.
✐ When the timer event ON occurs during cooling down period, this is invalid event because the projector cannot be
turned on during that cooling down period.
76
Projector information
Projector information
This page is to display the basic information of the projector status. Click
Information on the main menu.
Items
Description
Input............................Displays selected input and source.
System........................Displays selected signal system.
Signal..........................Input signal status
Screen.........................Displays screen mode.
Lamp status...............Displays lamp status with an animation. Refer to the
table on the next page.
Security......................Displays the security (PIN code lock) status
Click this button to
update the information
77
Chapter 7 Controlling the projector
Indication of the lamp status
Icon display/background
Status
White-Yellow/Blue
Lamp on (Normal)
White-Yellow/Red
Lamp on (Lamp is being used over a specified use time, replace lamp immediately)
Gray/Blue
Lamp off (Normal)
Gray/Red
Lamp off (Lamp is being used over a specified use time, replace lamp immediately)
Red/Blue with X
Lamp failure (Lamp failure, check the lamp condition)
Red/Red with X
Lamp failure (Lamp failure and lamp is being used over a specified use time, replace
the lamp immediately)
Items
Description
PJ time........................Displays the accumulated use time of the projector.
Lamp Corres.
Value...........................Displays the use time (Corresponding value) of the
lamp.
Filter time..................Displays the use time of the filter.
Timer...........................Displays the timer setting status.
ON Timer has been set.
OFF No timer setting.
78
Multi-control
Multi-control
Controlling and setting the multi-projectors
When you install multiple projectors in the network, you can control and set up them
together. Click Multi Control on the main menu to display the control page.
Note: To control the multiple projectors, each projector must be set the same Network PIN code.
Example of multi control
PJ1
PJ2
PJ3
PJ4
PC6
PC5
PC4
Select Input2 for
PJ1 to PJ4.
79
Chapter 7 Controlling the projector
Start/stop the multi control
To start or stop controlling the multi-projectors, click Multi
control setting menu and select ON or OFF.
Switches on and off the
multi-control function
Multi control setting
OFF...........Stops multi control function
ON.............Starts multi control function. The multi control
menu will appear when ON is set. These items of
menu are linked to the main menu.
The multi controllable menus are "Power & Status", "PC
adjustment", "Control", "Setting", "E-mail setting", "Timer", and
"SNMP setting". Click each menu and perform setting and
adjustment.
✐ The word "MULTI CONTROL" appears on the each control page while
the multi control is operating.
This shows the multi control is
operating now.
80
Multi-control
Register the projector
To use the multi control function, register the IP address of the projector you intend to control. Click PJ
registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button.
Items
Description
IP address..................Enter IP address of the projector to control
Memo.........................Enter projector name or installed location etc.
Multi control item
Control.................. Controlling the projector
Control & Image......... Controlling and displaying images
Image.................... Displaying the images
Confirmation of registered projector
To check the registered information, click Check & Change sub
menu tab. The registered information of the projector is listed as
the below.
* The word "none" is displayed if the "Memo" function is used.
* When you click on a listed IP address, the
login page for the selected projector will
be displayed with a new window.
IP address
Status
Memo
Page no.
Click here to close
the sub menu Check
& Change.
✐1
0 projectors can be registered per page and up to 100 sets can be registered for the multi-control.
81
Chapter 7 Controlling the projector
Change the mode of the registered projector
To change the mode of the registered projector, select a mode with the pull-down menu button under
the IP address of the target projector and then click Set button.
Mode
Operation
Control........................ Controlling the projector
Control & Image............... Controlling and displaying images
Image.......................... Displaying the images
OFF.............................. Excluding from the multi-control
Delete......................... Deleting from the multi-control
* T he multi control item is not changed during using theIt is not
available with the light mode.
Status
If some of the registered projectors are disabled by
some reasons (such as disconnecting the power source,
disconnecting the LAN cable, disconnecting from the network),
control changes will continue to be effective for the projectors
that are still active. At the same time, the deactivated projectors
are excluded from the multi-control. The status of the registered
projectors are indicated under the projector name. See the
table below for status indications.
Status
Status
Description
(blank).........................The projector is connected to the network correctly
No connect...............The projector may not be connected to the network. Please check the connection and network
configuration of this projector.
PIN code error..................The PIN code is incorrect. The PIN code for the multi-controlled projectors must be the same.
Change the PIN code of this projector to the common PIN code. (p.30, p.40)
File Error..................... Not displaying the images. Check if this projector is using the Network Capture function, or in
the standby mode.
* The projector updates the status at the time when the multi-control function is executed.
82
✐ I f the multi-controlled projector is in the standby mode, items of "PC adj.", "Control" and "Setting" cannot be
operated.
✐ I t is recommended that a specified projector should be chosen for setting as a master when you use this multicontrol function. The control for the multi-controlled projectors will become too complicated operation if this
function is used for each projector.
✐ I f the registered projector is not connected to the network, it will take a while to complete the multi-control
operation because of waiting for the response from each registered projector.
✐ There are some disabled items in the multi-control function for the light mode.
Multi-control
Check & Change page in the light mode
Following functions in the "Check & Change" page are not
available in the light mode.
- Changing the control mode.
- Deleting the registered IP address
- Indicating the each status
- Indicating the each memo
This indicates that the
mode is "Image".
Connection status
Blinking: Connected
Gray: Disconnected
This indicates that the
mode is "Control".
(Check & Change page in the light mode)
Controlling all together
"Power & Status", "PC adjustment", "Control" and "Setting" can
be controlled all together. Set "ON" the multi control setting and
adjust controls of each menu. The setting value is applied to the
registered projectors sequentially .
✐ This is effective only if the multi control item of the registered projector is
set to either "Control & Image" or "Control".
Setting all together
"E-mail setting", "SNMP setting" and "Timer" can be set all
together. Set "ON" the multi control setting and items of each
menu. The setting value is applied to the registered projectors
sequentially.
✐ This is effective only if the multi control item of the registered projector is
set to either "Control & Image" or "Control".
83
Chapter 7 Controlling the projector
84
Chapter
8
8. Network capture functions
Network Capture is a function to display the screen
image of the computer via the network.
- Real Time Capture
85
Chapter 8 Network capture functions
About Network Capture function
The Network Capture is a function to display the screen image of the computer which has a Network
Capture 5 software by the projector through the network. This function has a mode as below.
- Real Time Capture (+p.89)
A function to display the screen image of the computer by the projector through the network in real
time.
✐ Up
to 30 computers can be registered.
Start up the Network Capture 5
To start up the Network Capture 5, click "Network Capture 5" from "Macintosh HD" - "Application"
- "Network Capture 5" menu. The application window will appear and search the projectors in the
network and list them on the projector list.
If any projector is not listed, check followings and then search again by pressing Search PJ button.
- Is the projector turning on and connected to the network?
- Is the network setting of projector and computer configuring correct?
- Is the same capture port no. used among computer and projectors?
86
About Network Capture function
Commands on the menu bar
When the Network Capture 5 icon on the menu bar is clicked, the popup menu will appear. It provides
according to the operating modes as shown in the table below.
Network Capture activating
Parameter set up...
Window show..
Version information..
Shut down
Menu during Real time capturing
One-shot executing
Start real time capture
One-shot capture
Terminate capture
Window show..
Version information..
Shut down
Items
Real time capture executing
One-shot capture
Terminate capture
Window show..
Version information..
Shut down
Description
Start / Terminate capture.................... Starts / Terminates the real time capturing. (+p.89) The screen image of the computer
is projected on the screen in real time.
One-shot............................................ Transfers the one-shot screen image of the computer.
Select capture object*........................... Sets to display the capture window selection dialog.
* This menu will appear when "Select capturing object" is checked on the parameter
setting. (p.88)
Parameter set up................................ Sets the communication parameter between the computer and projector. For further
information, see item "Parameter set up" below.
Window show.................................... Displays the application window on the screen.
Version information............................ Displays the version of this software.
Shut down......................................... Quits the Network Capture 5 application.
87
Chapter 8 Network capture functions
Parameter set up
Click Parameter set up button and setup the parameters on the Parameter setup window.
Items
Description
Capture port................ Sets the capture port no. on the projector. Default is 9000.
Pincode.......................... Sets the Network PIN code on the projector.
PJ search time.............. Sets the time to search the projector between 1 to 60 seconds. Default is 5 seconds.
q Select normal network adapter Uses default setting. Default is un-checked.
q Auto-power on....... The projector turns on and projects the computer's captured image on the screen
automatically when the network capture is executed while the projector is in the standby.
Select capturing object..... Check if you want to select an individual window on the computer screen. This is useful
function when you open the multiple windows on the computer's screen. When you
execute the capturing, the window selection dialog appears. Select a window name
from the dialog window. The projected window size is automatically adjusted to fit the
projector's screen size.
Sharpness..................... Select a capturing picture
quality among "High,
"Medium", "Low"
Reduce image.............. Check if the capturing
image resolution is more
than projector's panel
resolution (XGA),
Capture start up time....... Sets the delayed time from
the capture start in second.
✐ To check the Capture Port number, see item "Control by the web browser" (☞ p.91). To check the PIN code, see item
"Network PIN code setting" (☞ p.30, p.40).
✐ S pecify the port number of TCP/IP. The default port setting is 9000. There are some reserved port numbers and also
some applications may use their own port numbers. If one of those port numbers is used, the alert dialog window
will appear and let you know that it is an invalid port number. In that case, use another port number.
✐ The reserved port numbers are http (80), ftp (21), telnet (23), (25), (110), etc. The port no. 4352, 10000, 10001 are
reserved to control the projector through the LAN port.
88
Using the Real Time Capture
Using the Real Time Capture
This is a function to project the screen image of the computer by the projector in real time. The
captured image projected by the projector can be selected from the computer, web browser and the
projector respectively.
Registering the computers
Up to 30 computers can be registered.
1 Access to the control page of the projector by using the web
browser. From the Network menu, click Capture tab to display
the setting page.
2 Switch to Connection Setting page by clicking the page
number tab [3]. Enter the IP address of the computer to the PC
number, and then click Set button. Click Set button to register
the IP address for each page.
✐ The registered computer enables to start capturing if only the Network Capture 5 is activated.
✐ The transfer speed of the captured image using the Real Time Capture function is depending on the network
environment and data volume of the image. It cannot be supported for movie pictures.
✐ "Spinning
wait cursor
" cannot be captured.
89
Chapter 8 Network capture functions
[1] Control by the computer
* PC provides the Network Capture.
PC1
PJ2
PJ1
Project
this screen
PC2
PC2
image with PJ2.
Capture
PC3
PC4
PC6
PC5
* Start capturing from the
PC1.
Select input mode to "Network" previously.
1 Start up Network Capture 5.
2 Select the projector(s) listed on the projector list on the application window and click Start real time
capture. The application window will disappear and then the screen image of the computer will
appear on the projected screen in real time.
* You can select multiple projectors (up to 5) on the projector list.
• To stop capturing, click One-shot on the popup menu appearing by clicking on the Network Capture
5 icon on the menu bar. The captured image of the computer on the screen is frozen.
• To restart capturing, click Capture start on the popup menu.
3 To end capturing, click Terminate real time capture on the popup menu appeared by clicking on the
Network Capture 5 icon on the menu bar.
One-shot capture
Terminate Capture
Window show..
Version information..
Shut down
90
✐ When you capture the screen image of the movie player software with the real time capture function, the projector
can not be able to reproduce the sound.
✐ I f the error message appears, check the item "Parameter set up" (+ p.88).
✐ The sound output from the projector can be controlled with the volume slider and mute item on the application
window of the Network Capture 5 software (+ p.24, p.86).
Using the real time capture
[2] Control by the web browser
* PC provides the Network Capture.
PC1
PJ2
PJ1
PC2
Capture
PC3
PC4
PC6
PC5
Project a screen
image of PC1 with
PJ2.
* S tar t capturing of
t h e P C1 f r o m t h e
PC5.
Select "Network" as input mode previously.
1 Access to the control page of the projector by using the web
browser. From the Network menu, click Capture tab to display
the setting page.
2 Select the computer number from the pull-down menu button
of "Connecting PC" and click Start button. The screen image of
the selected computer will appear on the projected screen in
real time.
• To stop capturing, click One-shot button. The captured image
of the computer on the screen is frozen.
• To restart capturing, click Start button.
3 To end capturing, click End button.
Set "On" when
using the wireless
mouse function
Item
Description
Interrupt connection................Set enable or disable the real time capturing
connection from other computers during executing
the real time capturing operation.
✐ The IP address of the connecting PC should be registered previously (☞ p.89).
✐ If the error message appears, check item "Parameter set up" (+ p.88).
✐ To use the capture function from the web browser or projector, the Network Capture 5 on the captured computer
must be activated.
91
Chapter 8 Network capture functions
[3] Control by the projector
* S tar t captur ing of
the PC1 from the
projector PJ2.
* PC provides the Network Capture.
PC1
PJ2
PJ1
PC2
Capture
PC3
PC4
PC6
PC5
Project a screen
image of PC1 with
PJ2.
Select "Network" as input mode previously.
1 Select "Network Capture" icon from "Network" menu. Press SELECT button on the projector twice to
display the network capture setting pallet.
2 Select PC number to connect .
3 Select "Connect" and then press SELECT button to start capturing. The screen image of the selected
computer will appear on the projected screen in real time.
4 To end capturing, select "Disconnect" and then press SELECT button.
Set "On" when
using the wireless
mouse function
92
✐ The IP address of the connecting PC should be registered previously (☞ p.89).
✐ If the error message appears, check item "Parameter set up" (+ p.88).
✐The projector does not provide the function to register the IP address of the computer and to set the parameter of
the capturing. They should be registered by using the web browser previously (☞ p.89-90).
Using the real time capture
Example of advanced use
Displays the presentation data stored in the computer by using the wireless mouse function
from the projector.
1 Start capturing of the computer PC1 by using the projector.
S elect “Network Capture” icon from the menu and select "PC1" and then select "Connect" (☞ p.92).
=> The Network Capture software installed in the selected computer will start capturing.
2 On the image of the PC1 projected on the screen, search a presentation file data stored in the PC1 by
using the wireless mouse function of the remote control supplied with the projector.
3 Select a desired file and double click with the remote control .
=> The application by which the document was created starts and the projector projects the presentation picture
on the screen.
4 Start the presentation.
=> By using wireless mouse function, control the page browsing and some other operations for the PC1.
✐ F or further instructions of the wireless mouse, please refer to the projector’s owners manual.
✐O
n the projected screen using with the network capture, the shape of the mouse pointer differs from the one on
the computer’s screen.
* PC provides the Network Capture.
PC1
PJ2
PC2
Project a screen
image of PC1
with PJ2.
Capture
PC3
PC4
PC5
* Controls PC1 with wireless mouse.
Setting condition
Projector
Input mode: Network
Registering the connection: The IP address of the computer and proper parameter must be set to the
PC1 (☞ p.89-90).
Mouse Display: "On" (☞ p.91)
Computer PC1
Software: The Network Capture 5 is activated.
93
Chapter 8 Network capture functions
Error information
Error information
94
Error messages
Cause and corresponding
Cannot be displayed as PJ is under
display.
Error when Start real time capture is executed. The other capture, viewer or
memory viewer function is now operating.
➔ Wait until the communication function is available.
Cannot connect to PJ.
Cannot establish the connection with the projector when Capture transfer,
Start real time capture or Terminate real time capture is executed.
➔ Check connection of the network cable.
Cannot transfer data to PJ.
Cannot transfer the data to the projector when Capture transfer, Start real
time capture or Terminate real time capture is executed. The time-out
period is 10 seconds.
➔ Check the connection of the network cable.
Invalid port number
When the parameter is set, the reserved port number is specified.
➔ Check the parameter setting (+p.88)
Chapter
9
9. Appendix
Use of telnet
Web browser setting
Firewall setting
Troubleshooting
Terminology
95
Chapter 9 Appendix
Use of telnet
You can control the projector by using the telnet application*1 installed on your computer. Normally,
the telnet application is available on your computer.
* The telnet 10000 port is used to control the projector.
Control
(For example, in case of using the telnet application of Mac OS v 10.4)
1. Select Terminal from Applications -->Utility. Type as below on the displayed window.
> telnet [return]
2. The telnet application will start and the following window will be displayed.
3. Type as below to connect the projector.
> open_172.21.99.251_10000 [return]
*Use the IP address assigned to the projector
4. When communication is established correctly, the word "PASSWORD:" appears on the window.
Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the
keyboard. If you do not set up the Network PIN code, just press "Enter" key.
When the word "Hello" is replied, login has been succeeded.
* The password "1234" is used for the example.
96
Use of telnet
5. Type the commands, refer to below table, to control the projector and then press "Enter" key for
termination. For example, type "C00" which is a command to turn on the projector, and press "Enter"
key. Confirm the projector is turning on.
To disconnect the communication, press "Control" key and "]" key at the same time.
The table below shows the typical command lists for controlling this projector and please consult your
local dealer for further information of another commands.
Command list table
Command Function
C00Power on
C02
Power off
C09
Volume up
C0A
Volume down
C0B
Audio Mute on
C0C
Audio Mute off
C1C
Menu display on
C1D
menu display off
*1 Further instructions about the telnet application, please see the on-line guide on your computer.
*2 The password is a Network PIN code decided item "Network PIN code setting" (☞p.30, 40). If the authentication of
the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please
try again for the connection.
97
Chapter 9 Appendix
Web browser setting
This product is designed to enable the projector to be set up and controlled from an Internet web
browser. Depending on the preference settings of the web browser, some control functions may not be
available. Please make sure that the following functions are set up properly in the web browser.
JavaScript enable
There are some control items used with the
JavaScript function in the setting pages. If the
web browser is set not to use this JavaScript
function, it may not control the projector
properly. In that case, the following warning
message will be displayed on the top of the
page. To enable the JavaScript, please see further
instructions on the next page.
Flash Player enable
The setting page of this product contains the
Flash contents. To display the setting page,
the Adobe Flash Player version 6 or later is
required to be installed on your computer. For
further product information, see the Adobe
homepage. (http://www.adobe.com). Even if
your computer provides the Adobe Flash Player,
the setting page does not appear on the web
browser, in which case, check that Flash Player
Plug-In(Shockwave Flash) is installed and set up
correctly. Please see further instructions on the next page and it is depending on the web browser.
Proxy setting
In some cases, your web browser is set up to use the proxy server for the internet or intranet
connection. In that case, when you install this product into the local network, you should set up the
proxy setting of web browser preference correctly. Especially when connecting the projector and
computer with a UTP cross cable directly, or when the network does not provide the proxy server,
make sure that "not use proxy server" is set up in your web browser preference. Please see item
"Examples: OS/Browsers" in the next page for further setting up procedure.
98
✐ There are various ways to change your browser preferences depending on the version or applications. Please see
the setting instructions on next page showing examples and also refer to on-line help of your web browser.
Web browser setting
Examples: OS/Browsers
MAC OS X v 10.4
Safari
JavaScript and Flash Player enable setting
Select Preferences... from Safari on the web browser and then select Security tab and check Enable
plug-ins (for flash player) and Enable JavaScript.
99
Chapter 9 Appendix
Proxy setting
1 Open Preferences... from Safari menu on the web browser Safari. The preference menu appears.
2 Select Advanced icon and then click Proxies: Change Settings ....
3 Select Proxies tab and properly set up your web browser Safari's the proxy server settings according
to the local area network environment to which the projector is connected.
- Using proxy server
To use an external internet connection from the local area network, check the items Web Proxy (HTTP)
and Secure Web Proxy (HTTPS) of Select a proxy server to configure window and enter the proxy
server address and port correctly in Web Proxy Server window. For further instruction please consult
your network administrator.
- Not using proxy server
Uncheck the items Web Proxy (HTTP) and Secure Web Proxy (HTTPS) of Select a proxy server to
configure.
If you connect the projector to the computer directly with UTP cross cable, it must be unchecked.
To designate proxy settings that will not use the
proxy server when accessing the projector installed
in the local area network, enter the IP address or
domain name here.
100
Firewall setting
Firewall setting for MAC OS X v 10.4
When you use Macintosh OS X v 10.4 and Network Capture 5, you can cancel the firewall blocking
following to the steps below;
1 Open System Preferences from Apple menu, click Sharing icon. The Sharing setting window will
appear.
2 Select Firewall tab and click "New...", then a dialog box appears.
3 Specify the items as follows;
Port Name
: Other
TCP Port Number(s) : 9000
UDP Port Number(s) : 9000
Description
: You can name as you like. "Network capture 5" on the figure is just an
example.
4 Click OK to close setting.
101
Chapter 9 Appendix
Firewall setting for MAC OS X v 10.5
If you use Macintosh OS X v 10.5 and Network Capture 5, you may see the security warning dialog
as below. In that case, click "Always Allow" button on the dialog to enable the function of Network
Capture 5.
Even if you select "Deny", you can cancel the
blocking following to the steps below;
1 O pen System Preference from Apple
menu, click Security icon. A security
setting window appears.
2 Select Firewall tab, check Limit incoming
connections to specific services and
applications, and then click "+". A finder
menu appears.
3 Select Network Capture 5 and click add
button. The application name will be
added in the column.
4 You can also select the options of "Allow
all incoming connections" or "Block all
incoming connections" according to the
local area network environment.
5 Close setting.
102
Troubleshooting
Troubleshooting
If you have any trouble in setup or operation of the projector, refer to the troubleshooting items and
check the relevant matters described.
■ The computer cannot connect projectors.
Wired LAN
Is the LAN cable connected to the projector properly?
Is the LINK/ACT lamp of the LAN terminal lighting properly?
Not lighting : The LAN setting of the projector is set “On”?
See “Wired LAN setting” in the projector menu.
The LAN cable is connected to the network HUB properly?
Wireless LAN
Is the WIRELESS indicator on the front panel of the projector lighting?
If there are not any problems, confirm the LAN setting again. Refer to the next item.
If the wireless LAN card provides the firewall function itself, set up to disable its function.
■ Wireless LAN Connection cannot be established.
AdHoc Mode:
When selecting LAN4(factory default setting)
Check each item in the Wireless Setting menu of the projector as follows:
*IP Address................................Is the address appropriate? Should not be the same as the other IP address.
*Sub net................................. Should be the factory default value, 255.255.0.0.
*Gateway............................... Should be the factory default value, 255.255.255.255
*Network Type..................... Should be AdHoc mode
*ESSID/SSID.......................... Should be the same as the setting of computer
->Check the setting for the computer
*Is the Wireless channel set as 11 both for the computer and the projector?
-> The factory default channel of the projector is 11.
*WEP (Wired Equivalent Privacy) Should be disabled. 103
Chapter 9 Appendix
Infrastructure Mode:
When selecting LAN5 (factory default setting)
Check each item below in the Wireless Setting menu of the projector as follows:
*IP Address............................... No setting is required.
*Sub net..................................... Should be the same as the setting of the access point
*Gateway................................... Should be the same as the setting of the access point
*Network Type......................... Should be the Infrastructure mode
*ESSID/SSID.............................. Should be same as the setting of the access point
Check the settings for projector Client computer
*IP Address............................... No setting is required. Automatically set as DHCP.
*Wireless Channel.................. Should be 11
*ESSID/SSID.............................. .Should be the same as the setting of the access point
*WEP...........................................Should be disabled.
*When LAN5 is used, it is necessary DHCP server is under the environment enabling those
servers communicate through networks. Some access points may have the DHCP function.
For detail of the settings, refer to the owner’s manual for the devices or consult a system
administrator of the network.
Is the segment where the projector is installed different from the computer?
Specify IP Address directly on the optional setting. Refer to “4. Wired LAN Configurations” ➔
“Confirming the Operation” (☞p.28–29).
■ Connection between computer and the projector via Wired LAN cannot be established.
When selecting LAN1 (factory default setting)
Check IP address, Sub net and Gateway of the projector and computer. For further details of the
configuration, contact your system administrator.
Is the segment where the projector is installed different from the projector?
Specify IP Address directly on the optional setting. Refer to “4. Wired LAN Configurations” ➔
“Confirming the Operation” (☞p.28–29).
■ Cannot start up the browser
Is the connection between PC and the projector with Network Capture 5 established?
No................. Check settings for Wireless/Wired LAN.
Yes................ Check settings of the proxy setting at browser. Refer to “Web browser setting”
(p.98).
104
Troubleshooting
■ Although the connection between PC and the projector is established, images are not projected on the screen.
Make sure Wireless/Wired is selected from the Input source menu of the projector.
■ Cannot be turned on/off with the web browser.
Make sure the settings of the projector are correct to use the projector with it.
Set the item Standby mode to "Normal" from Main menu ➔ Setting menu.
Refer to “7. Controlling the projector” ➔ “ Power control and status check” (☞p.65).
■ Wired / Wireless input cannot be changed. Network Capture 5 cannot be operated.
Restart the projector or Network Capture 5.
Execute "Wired factory default" or "Wireless factory default" menu on the projector.
Caution: After executing “Wired factory default" or "Wireless factory default" in the projector menu, all the network settings you have made will return to the factory
default settings. See the items "Wired factory default" (☞p.31) and "Wireless factory default" (☞p.39) for the each factory default value.
Network capture
■ Why doesn’t the computer screen appear on the projected screen?
1. Make sure that the input mode of the projector is "Network".
2. Check the parameter set up (☞p.88).
Make sure that the numbers of the capture port is the same as the projector’s port number. The
default port number is 9000. If the alert message "Invalid Port No." appears, your computer may
be using this port number already. In that case, use another port number.
3. Check the IP address of the computer is registered to the projector correctly (☞p. 89).
4. Make sure that your computer is not using the firewall function. The projector may not be able
to use the port due to this firewall function. In that case, please turn off this function temporarily.
There are also some port limitations on the network equipment such as router. Please consult
your network administrator.
■ Speed of playing back images are very slow.
When connecting on AdHoc mode, check which Wireless channel you are using.
If the computer using the same channel as yours is existing closely, the networking speed may be
reduced or the communication unstable. Change the channel to resolve the problem. The channels
of the projector and projector Client computer must be the same. Or adjust the Quality selection in
the parameter setting.
Refer to “Parameter set up” (☞p.88).
105
Chapter 9 Appendix
Terminology
DHCP server (Dynamic Host Configuration Protocol)
It is necessary to set an IP address for each computer or equivalent equipment when a network is
established by TCP/IP. If there exists DHCP server on the network, it will assign IP addresses to client
computers every time they request it. If there exists equipment with DHCP server functions (such as
a server and a router) on the network, the DHCP server function may be automatically operating. Ask
your system administrator whether the DHCP server is operating.
ESSID (Extended Service Set Identifier)
ESSID is the ID that is set to computers on Wireless LAN or access point in order to prevent each
computer from being crossed. The computers or access point to which the same ESSID is set can
communicate with each other. If an ESSID is different, it is impossible to communicate. ESSID
distinguishes between lowercase and uppercase characters, and allows you to use English one byte
characters and half-size symbols up to 32 characters.
WEP (Wired Equivalent Privacy)
WEP is a security protocol for Wireless LAN. It protects computers on Wireless LAN and access point
from unauthorized access by setting a description code onto them. It is necessary to set the same
decryption code for equipment.
Wi-Fi (the Standard for Wireless Fidelity)
Wi-Fi is short for Wireless fidelity and a marketing brand name for IEEE 802.11b High-Rate. Only
the products that have passed an inter-operation test carried by WECA is approved as Wi-Fi.
Any products approved as Wi-Fi are certified as interoperable with each other by WECA. It is
recommended to use the products approved by Wi-Fi when you introduce network equipment such
as local area network.
Wireless Channel
It is necessary to divide frequency spectrums into some Wireless channels for Wireless
communication, and to tune to the same channel between Wireless equipment. If you use the same
channel on the same floor, and there are some Wireless LANs that have a different ESSID for each, the
communication speed may become slow. In that case, using different channels for each Wireless LAN
is effective, which lowers a possibility of mutual interference between Wireless LANs
WECA (Wireless Ethernet Compatibility Alliance)
WECA is an organization promoting IEEE802.11b High -Range standard and assuring the
compatibility of products that meet the standard.
MAC address (Media Access Control Address)
MAC address is a physical address for every network interface. The MAC address consists of 6-byte
hex number. The first 3 bytes are a Vendor ID controlled and assigned by IEEE. The last 3 bytes are
controlled and assigned by the manufacturers of network interface (no duplication of MAC address).
Therefore, MAC address is a unique physical address in the world. Ethernet sends and receives frames
on the basis of MAC address.
106
Terminology
107
SO-MAC-KF3AC
NETWORK OWNER'S MANUAL FOR MACINTOSH
SANYO Electric Co., Ltd.
Download PDF
Similar pages