Epson Office Equipment Installation Instructions

Document Camera
User's Guide
Important Safety Instructions
Read this User's Guide and follow all safety instructions for your document camera. Keep this guide at hand for future reference.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
Environmental Precautions
Warning
Do not leave the document camera or the remote control with batteries inside a vehicle with the windows closed, in places where they will be exposed to direct sunlight, or
in other places that may become extremely hot. Thermal damage, fire, or malfunction may occur.
Do not use or store the document camera outdoors for an extended length of time, or where it may be exposed to rain, water, or excessive humidity. Fire or electric shock
may result.
Do not use the document camera in places where smoke from cigarettes may be present, where it will be exposed to greasy smoke, humidity, or steam (such as cooking
areas or near humidifiers), or where there is a lot of heat or dust. This can adversely affect the quality of the projected images.
Caution
Do not set up the document camera near high-voltage electrical wires or sources of magnetic fields. This may interfere with correct operation.
Operate in the proper environmental conditions. s p.80
Do not place or store the unit where it is accessible to small children. The unit may drop or tip over, causing personal injury.
Do not place the document camera where it will be subject to a lot of vibration or shock.
Electrical Precautions
Warning
Never open any covers on the document camera except as specifically explained in this User's Guide. Never attempt to disassemble or modify the document camera. Refer
all repairs to qualified service technicians.
Unplug the document camera from the outlet and refer all repairs to qualified service technicians under the following conditions:
• If smoke, strange odors, or strange noises come from the device
• If liquid or foreign objects get inside the device
• If the device has been dropped or the housing has been damaged
Continuing to use under these conditions may result in fire or electric shock.
Do not attempt to use any adapter other than the AC adapter and power cord included with the device. Using an improper adapter may cause damage, overheating, fire, or
electric shock.
Be sure to use the AC adapter with the proper voltage indicated in this guide. Use of a different power source may result in fire or electric shock.
If the AC adapter, power cord, or document camera is damaged, turn the power off, unplug the AC adapter from the electrical outlet, and contact your local distributor.
Using the damaged device may cause fire or electric shock.
Do not touch the device, the AC adapter, or the plug with wet hands. This may cause electric shock.
Do not use the power cable that is damaged. Fire or electric shock may result.
• Do not modify the power cable.
• Do not place heavy objects on top of the power cable.
• Do not bend, twist or pull the power cable excessively.
• Keep the power cable away from hot electrical appliances.
Take the following precautions when handling the plug. Failure to comply with these precautions could result in fire or electric shock.
• Do not overload wall outlets, extension cables, or power strips.
• Do not insert the plug into a dusty outlet.
• Insert the plug firmly into the outlet.
• Do not pull the power cable when disconnecting the plug; always be sure to hold the plug when disconnecting it.
Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.
Caution
Turn off the document camera and unplug it after use.
Make sure the power is turned off, the plug is disconnected from the outlet, and all cables are disconnected before moving the document camera.
Installation Precautions
Warning
If you apply adhesives to prevent the screws from loosening, or if you use lubricants or oils on the document camera, the document camera housing may crack. This could
cause serious injury. Do not use adhesives to prevent the screws from loosening and do not use oils or lubricants.
Caution
Do not place the document camera in an unstable location, such as on a shaky table or slanted surface. The document camera may drop or tip over, causing personal
injury. If you use a table, cart, or stand, make sure it is stable and will not fall over.
When using the mounting points under the document camera to secure it to a table, cart, or stand, fasten the bolts securely but do not overtighten them. Do not use
adhesives.
Do not place the document camera in a poorly ventilated place where heat can accumulate.
Do not place the document camera on a carpet, blanket, etc. or cover it during use.
Cleaning Precautions
Warning
Use a dry cloth (or, for stubborn stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid, aerosol cleaners, or solvents such as alcohol, thinner or
benzine.
Do not place any containers of liquid on top of or near the unit.
Do not spill liquid or spray fine mist into the document camera. Liquids entering the document camera may cause malfunction, fire, or electric shock. If you spilled liquid,
turn the power off, unplug the AC adapter from the electrical outlet, and contact your local distributor. Using the damaged device may cause fire or electric shock.
Do not insert or drop metal, flammable, or foreign objects into the document camera's vents or openings nor leave them nearby. Doing so may result in fire, electric shock,
or burns.
Caution
Unplug the AC adapter from the outlet before cleaning to prevent electric shock.
Usage Precautions
Caution
Do not look into the lens when the LED illumination lamp is on. The bright light can damage your eyes.
Do not use excessive force when adjusting the document camera. The document camera may be broken, resulting in personal injury.
Do not place heavy objects on document camera, or it may be damaged.
Do not try to press the arm flat or fold it backwards, or it may get damaged.
Battery Precautions
Warning
Incorrect battery usage may cause batteries to rupture and leak battery fluid, which could result in fire, injury, or corrosion of the remote control.
If liquid from a battery gets in your eyes, do not rub your eyes. Wash them well with clean water and contact a doctor immediately. If liquid enters your mouth, rinse
immediately with plenty of water and consult a doctor. If liquid from the battery comes in contact with your skin or clothes, wash with water to prevent possible skin
damage.
Keep batteries out of the reach of children. Batteries are a choking hazard and are very dangerous if swallowed.
Prepare two replacement manganese or alkaline AA batteries. Do not use any other kinds of batteries.
Insert batteries so that the polarities (+ and -) are correct. Not doing so may cause leakage, overheating, or explosion.
Do not use a new battery and an old battery, or different types of batteries at the same time. Doing so may cause leakage, overheating, or explosion.
Remove the batteries if you will not be using the remote control for a long period of time. When a battery runs down, take it out of the remote control immediately. If a
discharged battery is left inside for a long time, gas emitted from the battery may cause leakage, overheating, explosion, or damage to the remote control.
Do not heat batteries or put them into fire or water.
When you throw away the batteries, follow your area’s regulations regarding disposal or recycling.
Memory Card Precautions
Caution
We recommend backing up data on the document camera's internal memory, your USB drive, or SD card to another media. Data may be lost or damaged under the
following conditions.
• If the power cable is disconnected from the document camera while recording or exporting data
• If the SD card or USB drive is removed from the document camera while recording or exporting data
• If it is subjected to static electricity or electrical noise
• If it is used incorrectly
• If a malfunction occurs or if the device needs to be repaired
• If damage occurs due to a natural disaster
In addition to the situations mentioned above, Epson shall not be responsible for the loss of any data or damage to data even during a warranty period.
Introduction
You can use the Epson ELPDC12 document camera to capture and project pages from books or other documents, and even three-dimensional objects. With the
included software, you can create time-lapse photos and annotate images produced by the document camera.
Product Features
Included Items
•
•
•
•
•
•
•
•
Remote control with 2 AA batteries
Power cord and adapter
VGA cable
USB cable
Software CD
User's manual CD
Quick Start
Microscope adapter
Document Camera Parts
Name
Top/Side/Rear
Name
Function
A Camera head
s "Camera Head" p.12
B Remote receiver
Receives signals from the remote control.
C Control panel
s "Control Panel" p.12
Function
D Security slot
The security slot is compatible with the Microsaver
security system manufactured by Kensington.
s p.18
E Interface
s "Interface" p.13
F Security bar
Lets you attach a commercially available security
cable to lock the document camera in place.
s p.18
G SD card slot
Lets you save and display images on an SD card.
s p.38
Document Camera Parts
Name
Camera Head
F Camera arm
Function
Extends or retracts the camera arm to adjust the
height of the camera head.
Attention
Do not rub the lens with harsh materials or subject it to shock, as it can be
easily damaged. Use a soft cloth to gently wipe the lens.
Control Panel
Name
Function
A Microphone
Captures sound when you record a video.
B [
Changes the LED lamp status in three steps: bright,
dim, and off.
] Lamp switch
C LED lamp
Turn on this lamp when there is not enough light on
your document.
D Image rotation dial
Turns the displayed image ±90˚.
E Camera lens
Captures the image.
Name
Function
A [t] button
Turns the document camera power on or off.
B [Source] button
[ ][
]
[
[
C [Menu] button
Opens and closes the menu.
] Projects images from the document camera.
] Projects images from a computer.
Document Camera Parts
Name
D [
[
][
][
][
Function
][
] button
[Enter] button
] button When the menu screen is displayed, pressing these
buttons selects menu items and setting values.
Interface
Adjusts the image Brightness.
When the menu is displayed, pressing this button
confirms the current item.
E [Esc] button
Stops the current function. When the menu is
displayed, pressing this button moves to the
previous menu level.
F [Zoom] button
[z] [x]
Enlarges or reduces the image without changing the
projection size. s p.27
G [Focus] button
Press the [Focus] button to automatically focus the
image.
The unit cannot focus on objects that are
approximately 10 cm (4 inches) or less from the
surface of the camera lens.
A Composite port
Outputs composite video signals to a projector or
external monitor.
B Power (AC adapter) port
Connects the supplied power cord and adapter.
C Computer In port
Inputs image signals from a computer.
If you press and release the button, the image is
frozen. If you press and hold the button, the still
image is saved. s p.39
D Display Out port
Outputs image signals to a projector.
E HDMI port
Outputs image signals to a video device or computer
that is compatible with HDMI signal.
Starts and stops video recording.
F USB-A (TypeA) port
Lets you annotate live images by connecting a
commercially available USB mouse. s p.33
Lets you save and display images on a USB drive.
G USB-B (TypeB) port
Connects the document camera to a computer via
the supplied USB cable when using the included
software.
H Mic In port
Connects a commercially available microphone
when recording audio and video.
H [
I [
] button
] button
Name
Function
Document Camera Parts
Base
Name
Function
A Mounting points
You can attach the document camera to a table, cart,
or stand with commercially available M4 bolts.
s p.18
B Security bar
Lets you attach a commercially available security
cable to lock the document camera in place.
s p.18
Remote Control Buttons
Remote Control
Projector operations
Name
Function
A [t] button
When used with an Epson projector, turns the
projector on or off.* You cannot operate the
document camera with this button.
B [A/V Mute] button
Turns the video and audio of an Epson
projector on or off.*
C [Source Search] button
Changes the input source connected to an Epson
projector.*
*
This is not supported by some projectors. For more details, contact your local
dealer or the nearest service center provided in this guide.
s "Where to Get Help" p.69
Document camera operation
Name
Function
D [t] button
Turns the document camera on or off. You cannot
operate a projector with this button.
E [Auto Focus] button
Press the [Auto Focus] button to automatically focus
the image.
The unit cannot focus on objects that are
approximately 10 cm (4 inches) or less from the
surface of the camera lens.
F [Freeze] button
Freezes the current image; press the button again to
continue.
G [Menu] button
Displays and closes the menu.
H [ ][ ][ ][ ]
buttons
When the menu or Help screen is displayed,
pressing these buttons selects menu items and
setting values.
I [Enter] button
When the menu is displayed, pressing this button
confirms the current item.
Remote Control Buttons
Name
Function
J [Esc] button
Stops the current function. When the menu is
displayed, pressing this button moves to the
previous menu level.
K [Snapshot] button
[ ]
Captures still images.
L [Record] button
[ ]
Starts and stops video recording.
M [Zoom] button
[z] [x]
Enlarges or reduces the image without changing the
projection size. s p.27
N [Brightness] button
][ ]
[
Adjusts the image brightness.
O [Source] button
[
][ ]
[
[
P Remote control
light emitting area
Outputs remote control signals.
] Projects images from a computer.
] Projects images from the document camera.
Storing the Document Camera
When you're not using the document camera, simply fold its arm down as shown.
Caution
Do not try to press the arm flat or fold it backwards, or it may get damaged.
Securing the Document Camera
You can secure the document camera by fastening a cable to the security
bar, shown below, or by inserting a Kensington anti-theft cable into the
Kensington security port.
In addition, you can attach the document camera to a table, cart, or stand
at the mounting points indicated below. Use M4 bolts; you can thread them
into the document camera case to a maximum depth of 9 mm (0.35 inch).
A Mounting points
Attention
Fasten the bolts securely but do not overtighten them. Do not use adhesives.
Connecting
Follow the instructions in this section to set up the document camera and give a presentation.
Connecting to a Projector
You can connect the document camera to a projector using a standard
VGA cable, composite video cable, or HDMI cable, or to other video
equipment such as an external monitor.
a
a
b
Connect the document camera by one of the following methods:
VGA connection
You can also use the document camera with a computer.
s p.22
Choose the type of cable you will use, based on the type of port
that's available on your projector or other video equipment:
VGA port
(computer monitor style)
Composite video port
(yellow "RCA" style)
VGA cable (included)
Composite video cable
A Display Out port
B VGA cable
Composite video connection
HDMI port
HDMI cable
A Composite port
Connecting to a Projector
B Composite video cable
HDMI connection
A HDMI port
B HDMI cable
a
• When connecting with a USB cable, video from other output
ports is not displayed.
• When two or more cables are connected, the priority of video
output is HDMI > Display Out > Composite.
Connecting to a Computer
When you connect the document camera to your computer, you can use
the included software to capture, edit, and play back still images and videos.
s p.54
Connecting to a computer also lets you display PowerPoint slides or other
applications. You can easily switch back to the live camera image at any
time.
How you connect to your computer depends on the software you plan to
use:
• To use the included software, see "Connect for Use with the Document
Camera Software" p.22 below.
• If you don't plan to use the software or it's not installed on your
computer, see "Connect for Use Without the Document Camera
Software" p.23.
A USB cable
B VGA cable
Connect for Use with the Document Camera
Software
a
This connection method lets you use the included software, as well as
display PowerPoint slides or images from another application on your
computer. Make sure you've already installed the software. s p.55
a
Connect the document camera to your computer with a USB
cable, as shown.
b
Connect your computer to your projector using a VGA cable.
a
c
• When connecting with a USB cable, video from other output
ports is not displayed.
• You cannot display images by directly connecting the
document camera to a projector with a USB cable.
• Connect the document camera to a USB 2.0 port of a
computer. If you connect it to a USB 3.0 port, it may not
function normally.
It's also possible to connect with composite video, but most
computers lack this type of port.
Follow the instructions on p.56 to use the document camera
software.
Connecting to a Computer
a
B VGA cable
C VGA cable
D Display Out port
If an image doesn't appear on the screen, the document
camera's USB Mode may be set to Mass Storage; see p.67 to
change the setting. If you connected a laptop, see p.67 to
check your laptop settings.
c
Connect for Use Without the Document Camera
Software
This connection method lets you display PowerPoint slides or images from
another application on your computer, but you can't use the included
software.
a
If you're using a desktop computer, disconnect the monitor from
your computer.
b
Connect a VGA cable from your computer's monitor-out port to
the document camera's Computer In port.
A Computer In port
Connect a second VGA cable from the document camera's Display
Out port to your projector.
a
• If you connected a laptop but the image doesn't appear on the
screen, check your laptop settings. s p.67
• A video signal from the Computer In port can only be
output from a Display Out port.
Plugging In and Turning On
a
Connect the power adapter as shown and plug the adapter into a
wall outlet.
b
Press the [t] power button to turn on the document camera. It
takes about 20 seconds for the document camera to output an
image.
c
d
Turn on your projector.
Select the appropriate "source" on the projector depending on the
port to which you connected.
a
When you're done using the document camera, press the [t] power
button twice to turn it off, disconnect any cables, and fold down the
camera arm. s p.17
Displaying a Document or Other Materials
Positioning the Document Camera
a
Raise the camera arm while holding the body with your other
hand.
Attention
b
Rotate the camera arm as shown below.
c
Position the camera head above the display area.
Do not try to press the arm flat or fold it backwards, or it may get
damaged.
The camera arm can only rotate within the range shown below.
Displaying a Document or Other Materials
Projecting
a
Place your document on the table under the camera head. Align
the center of your document with the
mark on the side of the
document camera.
a
• You can quickly align letter- or A4-size paper with the guides
on the side of the document camera.
• The maximum paper size that can be projected is A3
landscape.
A Lamp switch
B Image rotation dial
C [Focus] button
c
Turn the dial on the camera head to rotate the image on the
screen.
a
b
If desired, you can rotate an upside-down image by pressing
the [Menu] button and select Image > Image Rotation > 180
degrees.
Slide the lamp switch to illuminate the document.
a
If necessary, you can adjust the brightness of the image using
the [
] or [
] on the document camera or remote control.
d
Press the [Focus] button on the document camera or the [Auto
Focus] button on the remote control. Your document is
automatically focused.
a
To sharpen hard-to-focus objects, press the [Menu] button and
select Image > Focus. Use the [ ] and [ ] arrow buttons to
adjust the focus.
Displaying a Document or Other Materials
e
To zoom in on part of the image, press the [Zoom] - [z] button on
the document camera or remote control. Press the [Zoom] - [x]
button to zoom out.
a
• You can zoom up to 16x. When using the digital zoom, you can
scroll the enlarged image by pressing the [ ], [ ], [ ], and [ ]
arrow buttons.
• When the Zoom Area Window function is On, the entire image is
displayed at the bottom-right of the screen with a box that indicates
the enlarged part when you increase the zoom ratio more than twice.
When it is Off, a box is displayed that indicates the enlargement
ratio. To enable the Zoom Area Window function, press the [Menu]
button and select Image > Zoom Area Window.
When Zoom Area Window is On:
When Zoom Area Window is Off:
• Depending on the output resolution of the projector or external
monitor, part of the area shown in the box at the bottom-right of
the screen may not be enlarged.
• Image quality may decrease when the image is enlarged.
Displaying a Document or Other Materials
Freezing an Image
Press and release the [ ] button to freeze the image. (If you press and
hold the button, it saves the image. s p.39)
After freezing the image, you can remove your document while leaving its
image displayed on the screen. Place your next document under the camera
lens and press the button again; your presentation continues without
interruption.
a
You cannot enlarge the image while the image is frozen.
Displaying Small Objects Up Close
To display a small object, lower the camera arm. You can place the lens
within approximately 10 cm (4 inches) of the object.
To further enlarge an object, press the [Zoom] - [z] button on the
document camera or remote control. Press the [Zoom] - [x] button to
zoom out.
Displaying Live Action or Whiteboard Images
You can use the document camera to display a lecture or presentation at
the front of a room, or to capture images of a whiteboard or chalkboard.
a
Press the [Menu] button and select Image > Image Rotation to 180
degrees to display the image upside-down.
a
Raise and rotate the camera head to face the front of the room.
b
Press the [Focus] button on the document camera or the [Auto
Focus] button on the remote control. The image is automatically
focused.
a
You can make an audio/video recording of the live presentation
in the document camera's 1GB internal memory, on an inserted
SD card, or with a connected USB drive or computer.
s p.40, p.60
Projecting Through a Microscope
To display objects as seen through a microscope, use the included
microscope adapter.
a
• Adjust the focus and zoom of a microscope before attaching to the
document camera.
• Images may not be displayed correctly depending on the optical
properties of your microscope.
A Buttons
B Adapter ring
a
Attach the microscope adapter to the image rotation dial. Press
the buttons and push the adapter in.
b
Place the camera head with the adapter directly over the
microscope lens. Fit the adapter to the diameter of the eyepiece
by pulling out the adapter ring. It extends up to about 5 mm (1/4
inch).
c
Press the [Menu] button and select Image > Microscope > On.
This optimizes the image settings for use with a microscope.
Projecting Through a Microscope
a
If you manually adjust the brightness or zoom after setting
Microscope to On in step 3, Microscope is automatically set to
Off.
Adding Annotations
When a USB mouse is connected to the document camera, the annotation
tools are displayed on the live camera image and you can add handwritten
or graphic annotations with the USB mouse.
a
a
• You can only use the annotation function when the live camera
image is displayed.
• USB mouse devices that require installation of a driver cannot be
used. Also, some USB mouse models may not be compatible.
Connect a USB mouse to the document camera.
Tool
A USB-A port
b
The annotation tool bar is displayed on the bottom of the screen.
c
Function
A Colors
Selects a color for the annotation.
B Line width
Selects a line width for the annotation.
C Graphics
Changes a graphic (straight, freehand, circle, or
square).
D Eraser
Clears an annotation with the selected eraser size.
E Clear all
Clears all annotations.
F Pointer
Selects a tool and adds annotations. The shape of
the pointer varies depending on the button or tool
that you select.
Select a tool. Click the icon with the left mouse button on the
annotation tool bar.
For example, when you draw a square:
Adding Annotations
a
d
Use the left mouse button to draw lines or graphics or erase
with an eraser.
Disconnect the USB mouse to end the annotation.
a
• You cannot use the on-screen menu while annotating.
• Images with your annotations cannot be saved.
Switching Between Your Computer and the Live Camera Image
If you've connected a computer (s p.22), you can show PowerPoint slides
or images from any other application on your computer. You can easily
switch back-and-forth between your computer application and the live
camera image.
• If you've connected your computer with a USB cable (s p.22), you can
use the document camera software to display captured images and
videos, or use another application of your choice. To display the live
camera image, make sure you've selected
Capture mode in the
document camera software. s p.56
• If you've connected your computer with a VGA cable (s p.23), use the
document camera's [Source] buttons to switch between your computer
and the live camera image:
To display your computer image (such as a PowerPoint presentation),
press the [Source] - [ ] button on the document camera or remote
control.
To switch back to the live camera image, press the [Source] - [ ]
button.
Displaying a Split Screen
If you have images saved in the document camera's internal memory or on
an SD card or USB drive (s p.38), you can display two images at the
same time.
a
a
When connecting to a computer with a USB cable, you cannot use this
function.
Press the [Menu] button and select Memory > Split Screen.
A Highlighted image
b
Use the [ ] and [ ] arrow buttons to select the source for the
highlighted image. You can select from these sources:
• Live Display to display the camera image
• Internal Memory to display an image stored in internal memory
• SD Card to display an image stored on an SD card, if one is
inserted
• USB Flash Drive to display an image stored on a USB drive, if
one is connected
You see this setup screen, with the left image highlighted:
a
c
• Images on the SD card or USB drive must be stored in the
proper format to be readable. s p.67
• When USB Flash Drive is not displayed, even if one is
connected, set USB Mode to Application.
Press the [Enter] button to confirm the selection.
Displaying a Split Screen
d
If you select Internal Memory, SD Card, or USB Flash Drive as
the source, you see a screen that lets you select which image to
use:
Use the [ ] [ ] [ ] [ ] arrow buttons to highlight the image
you want to display, and press [Enter] to select it.
Select Return to finish setting up the split screen.
e
Repeat steps 2 through 4 to select the source for the right side.
a
f
You cannot display the live camera image or video on both
sides of the screen.
Once you're done setting up both sides of the screen, press [ ]
then press [Enter]. The selected images appear side-by-side on the
screen.
a
When connecting to a projector with an HDMI cable, the
movie's audio is also played.
g
To exit split screen mode, press [Menu] or [Esc].
Saving Images and Displaying a Slideshow
Images captured by the document camera can be saved not only in the internal memory but also on an SD card or USB drive.
Also, stored images can be imported or exported between the document camera and an SD card or USB drive.
You can view them as a slideshow or on a connected computer.
a
•
•
•
•
SD and SDHC cards are supported.
When you save images on the SD card, make sure that it is not set to LOCK (write-protected).
USB drives with a security function cannot be used.
When connecting to a computer with a USB cable, you cannot use the functions described in this chapter except for s "Viewing and Managing Files from Your
Computer" p.44.
Saving Images
Captured still images are stored in the internal memory, an SD card, or a
USB drive. If there is more than one save destination, the priority is as
follows: USB drive > SD card > the internal memory. If the save destination
only has a small capacity remaining, the image is saved in the next
destination.
a
a
Images are saved in JPEG format.
You see the
displayed in the upper right of the screen, and the
image is saved.
Insert an SD card face-up or connect a USB drive, if needed.
a
d
Repeat steps 2 and 3 for any additional images you want to save.
a
a
When you store images on a USB drive, make sure you set
Function > USB Mode to Application.
b
Display the live camera image you want to save. Adjust any
settings, as needed.
c
Press the [ ] button to capture the image. Press and release
when you use the remote control, press and hold when you use
the control panel.
Using the control panel, if you press and release the button
without holding it, the image is frozen on the screen instead of
being saved in memory.
• If all of the save destinations only have a small capacity
remaining, "The memory is full." is displayed and the image is
not saved.
• Do not disconnect the power cable from the document
camera or remove an SD card or USB drive from the
document camera while exporting data. Otherwise, the data
may not be saved properly.
Recording Movies
The document camera’s live image is recorded in the internal memory, an
SD card, or a USB drive. If there is more than one save destination, the
priority is as follows: USB drive > SD card > the internal memory. If the
save destination only has a small capacity remaining, the image is saved in
the next destination.
a
a
• Movies are saved in AVI format. (Motion JPEG+PCM)
• You can record up to 2GB for each file.
a
Insert an SD card face-up or connect a USB drive, if needed.
d
To stop recording, press the [
a
a
b
Display the live camera image you want to save. Adjust any
settings, as needed.
a
c
When you store images on a USB drive, make sure you set
Function > USB Mode to Application.
Motor noises by zoom or focus may be picked up by the
internal microphone. Make sure you adjust the zoom or focus
settings before starting a recording, or use an external
microphone to record the audio. s p.40
Press the [
] button to start recording.
The elapsed time displayed while recording is not displayed on
the saved image.
] button again.
• If all of the save destinations only have a small capacity
remaining, "The memory is full." is displayed and the image is
not saved.
• If the memory becomes full during recording, the image
recorded up to that point is saved and recording stops.
• Do not disconnect the power cable from the document
camera or remove an SD card or USB drive from the
document camera while recording. Otherwise, the data may
not be saved properly.
Connecting an External Microphone
If you connect an condenser microphone to the document camera, the
audio from the microphone is also recorded along with a movie.
Recording Movies
a
• Press the [Menu] button and select Function > Ext. Mic. Volume to
adjust the recording volume of the external microphone.
• When an external microphone is connected, the internal microphone
is disabled.
• Plug-in power is not supported.
• Live audio from a microphone cannot be output.
A Mic In port
Exporting and Importing Images
The stored images in the internal memory can be exported to an SD card
or USB drive. Also, the stored images on an SD card or USB drive can be
imported to the internal memory. The steps below explain how to export
images in the internal memory.
a
Insert an SD card face-up or connect a USB drive, if needed.
b
Press the [Menu] button and select Memory > Internal
Memory.
c
Use the [ ] [ ] [ ] [ ] arrow buttons to highlight each image
you want to export, and press [Enter] to select it. (Press [Enter]
again to deselect it.) A checkmark is added to each selected
image.
a
d
Select Export(SD) or Export(USB) and press [Enter].
a
a
When importing images from an SD card or USB drive to the
internal memory, select SD Card or USB Flash Drive.
You see this screen, showing the images stored in internal memory:
e
To add checkmarks to all images, choose Select All. To remove
all checkmarks, choose Select All again.
When importing images from an SD card or USB drive to the
internal memory, select Import.
Do one of the following:
• Disconnect the SD card or USB drive
• If you want to leave the SD card or USB drive in the document
camera, press [Menu] or [Esc] to close the screen.
Exporting and Importing Images
a
• If you want to remove the SD card, press in on the card and
then pull it straight out of the slot. The SD Card screen
automatically closes.
• When USB Flash Drive is not displayed even if one is
connected, set USB Mode to Application.
Viewing and Managing Files from Your Computer
You can use your computer with a USB cable to access files stored in the
camera's internal memory. Before using the document camera like this, you
have to change the function of its USB port as described below.
a
Connect the document camera to your projector with a VGA cable,
composite video cable, or HDMI cable. s p.20
b
c
Turn on the document camera and projector.
d
e
Disconnect the projector from the document camera.
Press the [Menu] button and select Function > USB Mode.
Change the setting to Mass Storage.
Now connect the document camera to your computer with a USB
cable.
a
f
Use your computer to view the files, or to copy, move, or delete
them.
a
g
• The document camera does not have a built-in clock.
Therefore, when you view files from your computer, they
won't show the actual time they were created.
• Connect the document camera to a USB 2.0 port of a
computer. If you connect it to a USB 3.0 port, it may not
function normally.
If you copy images from your computer to the document
camera, they must be in the proper format to be readable.
s p.67
When you're done, disconnect the computer.
Caution
Before disconnecting the USB cable, make sure your files have finished
copying. Otherwise, they may be damaged.
h
i
A USB cable
The document camera's internal memory appears as an external
drive on your computer.
Reconnect the projector.
Press the [Menu] button and select Function > USB Mode.
Change the setting back to Application.
a
If you don't change the setting back, you won't be able to see a
live camera image when you use the document camera software.
If you don't plan to use the software, you don't need to change
the setting back.
Displaying a Slideshow
Once you have stored images on the document camera's internal memory
or on an SD card or USB drive, you can display a slideshow.
c
Attention
When you rotate an image, we recommend backing up data on the document
camera's internal memory, USB drive, or SD card to another media.
a
a
b
All checkmarked images are rotated 90 degrees clockwise.
Attention
In addition to images captured with the document camera, you can
display images stored in the inserted SD card or connected USB drive.
You can also display images copied to the document camera from your
computer (s p.44), but they must be in the proper format.
s p.67
When using this device to rotate and display images on the document
camera's internal memory, a USB drive, or an SD card, the original
image may be changed and then saved. You can only rotate up to 12
images at once.
a
Press the [Menu] button and select Memory.
Select Internal Memory (to view images in internal memory), SD
Card (to view images on your SD card, if inserted), or USB Flash
Drive (to view images on your USB drive, if connected).
You see a screen like this:
To rotate an image, use the [ ] [ ] [ ] [ ] arrow buttons to
highlight it and press [Enter] to select it. (Press [Enter] again to
deselect it.) A checkmark is added to the image. In the same way,
select any additional images you want to rotate, and then select
Rotate.
d
Use the [ ] [ ] [ ] [ ] arrow buttons to highlight each image
to be displayed in the slideshow, and press [Enter] to select it.
(Press [Enter] again to deselect it.) A checkmark is added to the
selected images.
a
e
Image quality may decrease slightly after rotating an image.
Also, if your photo is time-stamped, the date will be changed to
a default value.
To add checkmarks to all images, choose Select All. To remove
all checkmarks, choose Select All again.
Select Play/Slideshow to display the first image in the slideshow.
To start or stop the movie, press [Enter].
a
When connecting to a projector with an HDMI cable, the
movie's audio is also played.
Displaying a Slideshow
f
Press [ ] to advance to the next image.
g
End the slideshow by pressing [ ] while the last image is
displayed. Or press [Menu] or [Esc] to end the slideshow at any
time.
Press [ ] to return to the previous image.
Image Adjustments and Effects
The document camera provides a full range of image adjustments and effects, including freeze image, black-and-white, and the ability to display negative film in
true color.
Using the On-screen Menu
Press the [Menu] button on the document camera or remote control to
view the on-screen menu. For details of each item in the screen menu, see
s p.49.
You see this screen:
Use the [ ] [ ] [ ] [ ] arrow buttons to navigate the menu and adjust
the settings. Press [Enter] to select a setting. When you're done adjusting
the settings, press the [Menu] or [Esc] button to close the menu and save
your settings.
On-screen Menu List
Image Menu
Basic image adjustments such as focus, zoom, and brightness are discussed in "Displaying a Document or Other Materials" p.26. You can make these further
adjustments by pressing the [Menu] button to open the Image menu.
a
When projecting a live image, you can adjust the Image menu settings.
Setup Item
Explanation/Select
White Balance
Adjusts the image color based on the lighting in the room where you're presenting.
Auto: Automatically adjusts the image color according to the display environment.
Cloudy: Suitable for use in cloudy weather.
Daylight: Suitable for use in fair weather.
Fluorescent: Suitable for use in a room with fluorescent lighting.
Incandescent: Suitable for use in a room with incandescent lamps.
Focus
Lets you manually adjust the focus if auto-focus doesn't produce a sharp enough image.
Near: Adjusts the focus in.
Far: Adjusts the focus out.
Image Mode
Selects the setting to adjust for the image type you are displaying from the camera.
Normal: Default setting.
Text: Suitable for projecting black-and-white text.
Display: Suitable for directly projecting the display of a tablet PC etc.
Color/B&W/Negative
Displays the image in color or black-and-white.
Color: Displays the image in color.
Black&White: Displays the image in black-and-white.
Negative: Displays the image as a negative.
Image Rotation
Lets you rotate an upside-down image.
Normal: Displays the image as it actually is.
180 degrees: Displays the image upside-down.
On-screen Menu List
Setup Item
Explanation/Select
Zoom Area Window
Displays the entire image at the bottom-right of the screen with a box that indicates the section that is currently being enlarged by
the zoom function.
On: Enables Zoom Area Window.
Off: Disables Zoom Area Window.
Microscope
Optimizes the image settings if using with a microscope.
s "Projecting Through a Microscope" p.31
On: Sets the optimal image settings for use with a microscope.
Off: Returns to the normal settings.
Noise Reduction
Settings related to Noise Reduction.
On: Activates Noise Reduction. Use this setting if noise occurs.
Off: Deactivates Noise Reduction. If the delay in projected images bothers you, select Off.
Advanced
Makes advanced settings of live image.
Exposure: Adjusts the light volume of projected images. If the projected image is too dark or too bright to reproduce the original
colors, you can adjust the light volume. Set it to a positive value if the overall image is dark and to a negative value if it is bright.
Contrast: Adjusts the difference between bright and dark areas of images. Set it to a positive value to project vivid images and to a
negative value to project monotone images.
Color Adjustment: Adjusts the reddish and bluish colors of the whole image.
Edge Enhancement: Adjusts the emphasis on the contours of the image. Set it to a positive value for sharp images and to a
negative value for soft images.
Gamma: Adjusts the coloring that occurs while displaying the image. When a smaller value is selected, the dark areas of images
become brighter, but the lighter areas may become over-saturated. When a larger value is selected, you can reduce the overall
brightness of the image to make the image sharper.
Reset
Resets the Image menu settings to the default value.
Function Menu
Setup Item
Explanation/Select
USB Mode
Changes how the document camera functions when connected with a USB cable.
Application: Enables use of a USB drive and the included software. This is the default setting when turned on.
Mass Storage: Lets you use a computer to view images stored in the internal memory.
Ext. Mic. Volume
Adjusts the recording volume from an external microphone.
On-screen Menu List
Setup Item
Explanation/Select
HDMI Output
Sets the output resolution when connecting with an HDMI cable.
Auto: Automatically set according to the resolution of the output device.
SDTV (480p)
HDTV (720p)
HDTV (1080p)
Output Resolution
Sets the output resolution when connecting with a VGA cable.
Auto: Automatically set according to the resolution of the output device.
XGA 1024x768
WXGA 1280x800
WXGA 1360x768
SXGA 1280x1024
Full HD 1920x1080
Video Format
Selects the video output signal.
NTSC
PAL
Flickerless
Eliminates flicker when giving presentations in regions with different electrical systems.
50Hz
60Hz
Language
Changes the on-screen menu language.
Sleep Mode
Operation settings when the document camera is inactive.
On: The power automatically turns off if the document camera is inactive for a certain amount of time.
Off: The power remains on even if the document camera is not being used.
Sleep Mode Timer
Sets the time from when the document camera is last operated until when the power automatically turns off.
1 to 6 hour(s)
On-screen Menu List
Memory Menu
Setup Item
Explanation/Select
Split Screen
Simultaneously displays two images from the internal memory, an SD card, a USB drive, or the live image.
Left Source: Selects the image to be projected on the left side.
Right Source: Selects the image to be projected on the right side.
Internal Memory
Operations related to the internal memory.
Export(SD): Exports the selected images to an SD card.
Export(USB): Exports the selected images to a USB drive.
Play/Slideshow: Displays the selected images in a slideshow.
Select All: Selects all images in the internal memory.
Delete: Deletes selected images.
Rotate: Rotates selected images 90 degrees clockwise and saves them.
SD Card
Operations related to an SD card.
Import: Imports selected images to the document camera's internal memory.
Play/Slideshow: Displays the selected images in a slideshow.
Select All: Selects all images on an SD card.
Delete: Deletes selected images.
Rotate: Rotates selected images 90 degrees clockwise and saves them.
USB Flash Drive
Operations related to a USB drive.
Import: Imports selected images to the document camera's internal memory.
Play/Slideshow: Displays the selected images in a slideshow.
Select All: Selects all images on a USB drive.
Delete: Deletes selected images.
Rotate: Rotates selected images 90 degrees clockwise and saves them.
On-screen Menu List
Info Menu
Setup Item
Explanation
Memory Capacity
Free Space: Displays the remaining capacity of the document camera’s internal memory.
Total Size: Displays the total capacity of the document camera’s internal memory.
Number of Files
Displays the number of files saved in the document camera’s internal memory.
Version
Displays the firmware version of the document camera.
Using the Included Software
The included software lets you use the document camera to capture still images, make time-lapse movies, record live videos with audio, and edit and play back
captured files. The software also lets you annotate images from the document camera with text and graphics, and upload your videos to popular websites.
Before starting, follow the instructions in this section to install the software.
a
For detailed help when using the software, do one of the following:
Windows: Press F1 or select Application Help from the Extras menu.
Mac OS X: Select Help from the menu bar.
Installing the Software
You can install the software on a Windows or Mac OS X computer. See
p.82 for system requirements.
Windows 7/Windows Vista/Windows XP
a
Windows 7/Windows Vista: Select Control Panel > Programs and
Features. In Classic View, select Programs > Uninstall a program
instead.
Windows XP: Select Control Panel > Add or Remove
Programs.
a
b
Press the [t] power button to turn on the document camera.
c
Insert the CD labeled "EPSON Document Camera Software" into
your computer.
b
Select ArcSoft Application Software for Epson Document
Camera.
d
e
When you see the license agreement, click Yes.
c
Windows 7/Windows Vista: Click Uninstall/Change.
Windows XP: Click Change/Remove.
Connect the document camera to your computer with a USB
cable. s p.22
Follow the instructions on the screen to install all the software.
a
When you see a screen asking if you want to install the Button
Manager and TWAIN Driver for Epson Document camera
(Windows only), be sure to allow the software to install.
Uninstalling the Software
Follow these steps if you need to uninstall the software.
Windows 8
a
Select Search on the Charms, and then right-click (press and hold)
ArcSoft Application Software for Epson Document Camera.
b
c
Select Uninstall from the app bar.
Select ArcSoft Application Software for Epson Document
Camera, and then select Uninstall.
Mac OS X
a
b
Open the Applications folder.
Drag the ArcSoft Application Software for Epson Document
Camera to the Trash.
Starting the Software
a
Connect the document camera to a computer with a USB cable.
s p.22
the software:
b •Start
Windows 8: Select Search on Charms, and then select ArcSoft
Application Software for Epson Document Camera.
• Windows 7/Windows Vista/Windows XP: From Programs or All
Programs, select ArcSoft Application Software for Epson
Document Camera. If the software does not start, install the
Windows Media Player.
• Mac OS X: Open the Applications folder, then double-click
ArcSoft Application Software for Epson Document Camera.
You see the screen shown below.
a
If you see a message that the document camera is not found,
make sure it is connected and turned on. Then click the
Connect button in the upper-right corner of the screen.
A
B
C
D
E
F
Main modes (capture, edit, and file management)
Capture album (previously captured images)
Capture buttons (still image, burst, time-lapse, and video)
Live Annotation button
Preview area (live camera image)
Connect button
Annotating Images
You can annotate live images from the document camera with text and
graphics while giving a presentation. When you capture an image, your
annotations will be included with the image; if you record your presentation
as a video, the recording will show your annotations as they're being
added.
a
You can also annotate still images after they've been captured using
the Edit screen. s p.62
a
If necessary, click the
Capture button to enter Capture mode.
Your live camera image appears in the preview area.
b
Click the Live Annotation button.
c
d
Select a drawing tool, such as Pen, Line, or Text.
Change the properties of the selected tool.
e
f
Use the selected tool to add text and graphics.
To clear an annotation, use the Eraser tool or click the Undo
button to clear the last change you made. To clear all annotations,
select the Eraser tool and then click the Clear all button that
appears above the preview area.
To save an annotated image, click the Take Picture button at the bottom of
the screen. s p.58
To record a video that shows annotations as they're being made, see
p.60.
Capturing Still Images
You can capture a still image or a quick series of images (called a burst).
a
If necessary, select the settings you want to use. Click the Settings
button and select the Image tab.
• Select the default image format, quality level, and other properties.
• Choose the number of photos, up to 10, that will be captured
with each burst (5 is the default).
b
c
To capture a still image, click the Take Picture button.
To capture a quick series of images, click the Burst button.
Your captured image(s) appear in the Capture album on the left side
of the screen. To display a captured image through your projector,
double-click the image or right-click it and select Preview.
Making Time-lapse Movies
You can record a time-lapse movie to show gradual changes that occur over
several hours.
the Settings button and select the Time Lapse tab.
a •Click
Set the time interval between each frame (5 seconds minimum).
• Set the total capture duration (up to 72 hours).
Click OK to close the Settings screen.
b
Click the Start Time Lapse button to begin capturing images.
When the process is done, the time-lapse movie or image appears as
an icon in the Capture album on the left side of the screen. To
display the movie through your projector, double-click the icon or
right-click it and select Preview.
Recording Videos
You can make an audio/video recording of your presentation. Set the
resolution under Full HD (1920×1080).
a
If necessary, select the settings you want to use. Click the Settings
button and select the Video tab.
• Select the default video format, quality level, and other properties.
• Set the maximum duration of each video (up to 8 hours) and see
how much hard disk space it will use.
b
To capture sound, click the Settings button, select the Audio tab,
and select ELPDC12 from Audio Device.
c
Click the Record Video button to start recording. Click Record
Video again to stop.
You can also use the [
stop recording.
a
] button on the control panel to start and
To start recording using the [ ] button, Button Manager
needs to be installed and running on your computer.
Your movie appears as an icon in the Capture album on the left side
of the screen. To display the movie through your projector, doubleclick the icon or right-click it and select Preview.
When you connect with the computer, you cannot use two
document cameras at the same time.
Compatible File Format
Type
Still images
Extension
.jpg/.bmp
Recording Videos
Type
Videos
Extension
Windows:
.wmv (WMV2+WMA)
.avi (YUV+PCM)
.mpg (MPEG Video+ MPEG Audio)
Mac OS X:
.mov (Motion JPEG+PCM)
Editing Saved Files
You can use the Edit screen to improve the quality (such as brightness and
contrast) of captured pictures and videos. With still images, you can zoom
in on part of the image, rotate the image, or flip it to create a mirror image.
You can also annotate still images. While viewing a video, you can pause it
and capture a still image from the current frame.
a
Click the
b
For detailed help when using the software, do one of the
following:
Windows: Press F1 or select Application Help from the Extras
menu.
Mac OS X: Select Help from the menu bar.
Edit button to enter Edit mode.
Managing Saved Files
You can use the File Management screen to sort and locate captured images
and videos. By rating them and applying "tags" or descriptive text, you can
make it easier to find them later on.
a
Click the
mode.
b
For detailed help when using the software, do one of the
following:
Windows: Press F1 or select Application Help from the Extras
menu.
Macintosh: Select Help from the menu bar.
File Management button to enter File Management
Uploading and Sharing Your Videos
You can easily upload your videos to popular video-sharing websites, such
as YouTube and SchoolTube.
a
This feature is not available for Apple Macintosh systems.
a
Click the
b
c
d
Select a video.
Edit button.
Select a website.
Follow the instructions on the screen to log in, provide a title for
your video and other descriptive information, and upload the file.
Problems and Solutions
Operation Problems
Image Quality Problems
No image appears on the screen
The image is fuzzy or out of focus
• After you press the [t] Power button, wait a few moments for the
image to appear. It takes about 20 seconds for the document camera to
output an image.
• Make sure your projector is connected. s p.20
If you're connecting it through a computer, see p.22.
• If you've connected a laptop, see "Problems Connecting a Laptop"
p.67.
• The document camera may be set to display an image from your
computer. Press the [Source] - [ ] button on the document camera or
remote control to display the live camera image.
• Select the correct source on your projector. The source refers to the
port on the projector to which you've connected the video cable. If
you're using a VGA cable, the source may be called something like
"Computer" or "PC".
• Make sure your projector is turned on and not in sleep mode. Make
sure its picture has not been "muted" or turned off.
• If you made a USB connection, the document camera's USB Mode
setting may be set to Mass Storage.
You need to change this setting to Application. First disconnect the
USB cable, then reconnect to the projector using a VGA cable,
composite video cable, or HDMI cable. Press the [Menu] button and
select Function > USB Mode, then change the setting to Application.
Now you can use the USB cable to display the image.
• The document camera needs hard edges or sharp lines in the image to
be able to focus properly. If the image has only soft edges, try placing a
different document under the camera lens while adjusting the focus. Or
focus the image manually with the Focus adjustment in the Image
menu. s p.49
• Make sure the lens is at least 10 cm (4 inches) away from the object
you're viewing.
• If you're using a projector to display the image, check its focus.
The image brightness or color isn't correct
• To illuminate your document, slide the lamp switch on the side of the
camera head.
• Press the [
] or [
] button to increase or decrease image brightness.
• Set the White Balance setting to Auto to adjust the color automatically.
s p.49
If the color is still not correct, choose the setting for the type of
lighting you're presenting under (Cloudy, Daylight, Fluorescent, or
Incandescent).
• If the document camera was used with a microscope, be sure to turn
the Microscope setting off when you return to displaying ordinary
documents. s p.49
Other image problems
• If the image is stretched or has black bars, you may need to change the
Output Resolution in the Function menu.
a
If you think some settings may have been changed, you can use the
Reset option to return all the image settings back to their standard
values except the Output Resolution setting. s p.50
Problems and Solutions
Problems Using an SD Card
Certain images don't appear
If you use your computer to copy images to the document camera's internal
memory or an SD card, you need to make sure their format is correct:
• Images must be DCF-compliant JPEG files to be displayed, such as
from a digital camera. Avoid editing your images, as this may change
their format and prevent them from being displayed.
• Images must be named using the format ABCD1234.JPG, where ABCD
is any combination of upper- or lowercase letters and 1234 is any
combination of numbers. For example: Pict0001, Pict0002, etc.
• Images must be placed in a folder named DCIM\123ABCDE, where 123
is any combination of numbers and ABCDE is any combination of
upper- or lowercase letters. If this folder structure doesn't exist, first
create a folder named DCIM, then create a folder within it with the
desired name (for example, 100EPSON).
Image files don't have the correct time stamp
The document camera does not have a built-in clock. Therefore, when you
view captured image files from your computer, they won't show the actual
time they were created.
Problems Using a USB Drive
Images stored on a USB drive are not displayed
The document camera's USB Mode setting may be set to Mass Storage.
Press the [Menu] button and select Function > USB Mode, then change the
setting to Application.
Image files don't have the correct time stamp
The document camera does not have a built-in clock. Therefore, when you
view captured image files from your computer, they won't show the actual
time they were created.
Problems Connecting a Laptop
If you've connected a laptop computer (s p.22) but the image doesn't
appear on the screen, check the following:
• Windows:
or
Hold down the Fn key and press the function key (such as
CRT/LCD) that lets you display on an external monitor. On most
systems, the
or CRT/LCD key lets you toggle between the LCD
screen and the projector, or display on both at the same time.
Check your monitor settings to make sure both the LCD screen and the
external monitor port are enabled. From the Control Panel, open the
Display utility. Click the Settings tab, then click Advanced. The method
for adjusting the settings varies by brand; you may need to click a
Monitor tab, then make sure the external monitor port is set as your
primary display and/or enabled. See your computer's documentation or
online help for details.
• Mac OS X:
From the Apple menu, select System Preferences, then click Display or
Displays. Select VGA Display or Color LCD, click Arrangement or
Arrange, and make sure Mirror Displays is checked.
Problems Using the Document Camera Software
There are no images stored on the USB drive
The buttons on the document camera don't work with the software
The document camera's USB Mode setting may be set to Mass Storage.
Press the [Menu] button and select Function > USB Mode, then change the
setting to Application.
When you installed the software, the Button Manager and TWAIN Driver
for Epson Document camera (Windows only) weren't installed. Reinstall all
Problems and Solutions
the software, being sure to allow the Button Manager and TWAIN Driver
for Epson Document camera to install.
You don't see the live camera image on your computer
The document camera's USB Mode setting may be set to Mass Storage.
You need to change this setting to Application. First disconnect the USB
cable, then reconnect to the projector using a VGA cable, composite video
cable, or HDMI cable. Press the [Menu] button and select Function > USB
Mode, then change the setting to Application. Now you can use the USB
cable to display the image.
Specifications
General Specifications
ELPDC12
Product name
Open (W ^ D ^ H): 270 ^ 331 ^ 476 mm (10.6 ^ 13.0 ^ 18.7 inches)
Folded (W ^ D ^ H): 340 ^ 124 ^ 125 mm (13.4 ^ 4.9 ^ 4.9 inches)
Dimensions
1/2.7 inch CMOS sensor
Type of sensor
F=2.8
Lens
2 megapixel (1920 ^ 1080)
Effective pixels
XGA: 29.7 ^ 41.9 cm (11.7 ^ 16.5 inches)
1080p: 29.7 ^ 52.6 cm (11.7 ^ 20.7 inches)
Imaging area
Focus adjustment
Automatic/manual
Zoom adjustment
16x digital
Up to 30 fps
Frame rate
1GB
Internal memory
1 (monaural input)
Internal microphone
Power supply
100-240VAC ±10%, 50/60Hz
AC adapter
12VDC
ELPDC12
Operating: 17 W
Standby: 0.48W
Power consumption
+5 to +35˚C (41 to 95˚F), non-condensing
Operating temperature
-10 to +60˚C (14 to 140˚F), non-condensing
Storage temperature
Operating humidity
20 to 80% RH, non-condensing
Storage humidity
10 to 90% RH, non-condensing
Approx. 2.9 kg (6.4 lb)
Weight
Input port
Computer In port
1
Mini D-Sub15-pin (female)
Mic In port
1
Stereo mini pin jack (monaural input)
Specifications
Output port
Connector port
*
Display Out port
1
Mini D-Sub15-pin (female)
Output: SXGA/WXGA(1280x800)/WXGA(1360x768)/XGA/Full HD
Composite port
1
RCA pin jack
Output: NTSC/PAL
HDMI port
1
HDMI
Output: SDTV(480p)/HDTV(720p, 1080p)
USB-A port *
1
USB connector (TypeA)
USB-B port *
1
USB connector (TypeB)
Output: QVGA/VGA/SVGA/SXGA/XGA
SD card slot
1
SD/SDHC card compatible
USB 2.0 is supported. However, the operation of all USB compatible devices is not guaranteed.
Specifications
System Requirements
These system requirements are for using the included software:
Windows: Microsoft Windows 8 32/64-bit, Windows 7 32/64-bit, Windows
Vista 32-bit, Windows XP (Service Pack 3 or later)
Mac OS X: Mac OS X 10.5 to 10.8
CPU: Pentium 4 1.4 GHz or higher (Windows XP)/Pentium 4 2.4 GHz or
higher (Windows Vista/Windows 7)/PowerPC G5 1.8 GHz processor or
Intel Core processor
Memory: 512 MB or more
Available hard disk space: 300 MB or more of available hard disk space is
required before installation
Monitor: SVGA (800 x 600) or higher resolution
This product is also designed for IT power distribution system with phaseto-phase voltage 230V.
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television
reception. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification of this device and may
cause interference levels which exceed the limits established by the FCC for
this equipment. It is the responsibility of the user to obtain and use a
shielded equipment interface cable with this device. If this equipment has
more than one interface connector, do not leave cables connected to unused
interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
For Canadian Users
Download PDF
Similar pages