SUPER STORAGE SYSTEM
6048R-E1CR24N
USER’S MANUAL
1.0b
Preface
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other reproductive harm.
Manual Revision 1.0b
Release Date: April 27, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the 6048R-E1CR24N. Installation
and maintainance should be performed by experienced technicians only.
The 6048R-E1CR24N is a high-end storage system based on the SC846E16-R920B
4U rackmountable chassis and the X10DRi-T4+ dual processor serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
system and describes the main features of the X10DRi-T4+ serverboard and the
SC846E16-R920B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the 6048R-E1CR24N into a
rack and check out the server configuration prior to powering up the system. If your
server was ordered without processor and memory components, this chapter will
refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Warning Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
6048R-E1CR24N.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
iii
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
Preface
Notes
Chapter 5 provides detailed information on the X10DRi-T4+ serverboard, including the locations and functions of connections, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC846E16-R920B chassis.
You should follow the procedures given in this chapter when installing, removing
or reconfiguring hard drives and when replacing system power supply units and
cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications
iv
v
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Table of Contents
Table of Contents
Chapter 3 System Interface
3-1Overview.......................................................................................................... 3-1
3-2
Chapter 1 Introduction
1-2
1-3
1-4
Power............................................................................................................... 3-1
Serverboard Features...................................................................................... 1-2
Processors....................................................................................................... 1-2
Control Panel Buttons...................................................................................... 3-1
Reset................................................................................................................ 3-1
1-1Overview.......................................................................................................... 1-1
3-3
Control Panel LEDs......................................................................................... 3-1
Memory............................................................................................................ 1-2
Power Fail........................................................................................................ 3-2
Main Storage Controller................................................................................... 1-2
Information LED............................................................................................... 3-2
Serial ATA......................................................................................................... 1-2
NIC1................................................................................................................. 3-2
PCI Expansion Slots........................................................................................ 1-2
NIC2................................................................................................................. 3-3
Rear I/O Ports.................................................................................................. 1-3
HDD.................................................................................................................. 3-3
Server Chassis Features................................................................................. 1-3
Power............................................................................................................... 3-3
System Power.................................................................................................. 1-3
3-4
Hard Drives...................................................................................................... 1-3
Chapter 4 Standardized Warning Statements for AC Systems
Drive Carrier LEDs........................................................................................... 3-3
Front Control Panel.......................................................................................... 1-3
4-1
About Standardized Warning Statements........................................................ 4-1
Cooling System................................................................................................ 1-3
Warning Definition............................................................................................ 4-1
Contacting Supermicro..................................................................................... 1-5
Installation Instructions..................................................................................... 4-4
Circuit Breaker................................................................................................. 4-5
Chapter 2 Server Installation
2-1Overview.......................................................................................................... 2-1
Power Disconnection Warning......................................................................... 4-6
2-2
Unpacking the System..................................................................................... 2-1
Equipment Installation...................................................................................... 4-8
2-3
Preparing for Setup.......................................................................................... 2-1
Restricted Area................................................................................................. 4-9
Choosing a Setup Location.............................................................................. 2-1
Battery Handling............................................................................................. 4-10
Warnings and Precautions............................................................................... 2-2
Redundant Power Supplies........................................................................... 4-12
Rack Precautions............................................................................................. 2-2
Backplane Voltage......................................................................................... 4-13
Server Precautions........................................................................................... 2-2
Comply with Local and National Electrical Codes......................................... 4-14
Rack Mounting Considerations........................................................................ 2-3
Product Disposal............................................................................................ 4-15
Ambient Operating Temperature................................................................. 2-3
Hot Swap Fan Warning.................................................................................. 4-16
Reduced Airflow.......................................................................................... 2-3
Power Cable and AC Adapter ....................................................................... 4-18
2-4
Mechanical Loading.................................................................................... 2-3
Chapter 5 Advanced Serverboard Setup
Circuit Overloading...................................................................................... 2-3
5-1
Precautions...................................................................................................... 5-1
Reliable Ground.......................................................................................... 2-3
2-5
Installing the System into a Rack.................................................................... 2-4
Handling the Serverboard................................................................................ 5-1
5-2
Connecting Cables........................................................................................... 5-2
Separating the Sections of the Rack Rails...................................................... 2-4
Connecting Data Cables.................................................................................. 5-2
Installing the Inner (Chassis) Rails.................................................................. 2-5
Connecting Power Cables............................................................................... 5-2
Connecting the Control Panel.......................................................................... 5-2
Installing the Outer (Rack) Rails...................................................................... 2-6
Installing the Sytem into a Rack...................................................................... 2-7
5-3
Rear I/O Ports.................................................................................................. 5-3
Installing the Chassis into a Rack................................................................... 2-8
5-4
Installing the Processor and Heatsink............................................................. 5-4
vi
vii
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
5-5
Table of Contents
Installing an LGA2011 Processor..................................................................... 5-4
Chapter 7 BIOS
Installing a CPU Heatsink................................................................................ 5-7
7-1 Introduction....................................................................................................... 7-1
Removing the Heatsink.................................................................................... 5-7
Starting BIOS Setup Utility............................................................................... 7-1
Installing Memory............................................................................................. 5-8
How To Change the Configuration Data.......................................................... 7-1
Memory Support............................................................................................... 5-8
How to Start the Setup Utility.......................................................................... 7-2
DIMM Installation............................................................................................. 5-8
7-2 Main Setup....................................................................................................... 7-2
5-6
Adding PCI Add-On Cards..............................................................................5-11
7-3 Advanced Setup Configurations...................................................................... 7-4
5-7
Serverboard Details....................................................................................... 5-12
7-4 Event Logs..................................................................................................... 7-34
X10DRi-T4+ Quick Reference....................................................................... 5-13
7-5 IPMI................................................................................................................ 7-36
X10DRi-T4+ Quick Reference (cont.)............................................................ 5-14
7-6
Security Settings............................................................................................ 7-38
5-8
Connector Definitions .................................................................................... 5-15
7-7
Boot Settings.................................................................................................. 7-39
5-9
Jumper Settings............................................................................................. 5-22
7-8 Save & Exit.................................................................................................... 7-41
5-10 Onboard Indicators......................................................................................... 5-25
5-11 SAS/SATA Ports............................................................................................. 5-26
5-12 Installing Software.......................................................................................... 5-27
Appendix A BIOS Error Beep Codes
Appendix B System Specifications
SuperDoctor® 5............................................................................................. 5-28
5-13 Onboard Battery............................................................................................. 5-29
Chapter 6 Advanced Chassis Setup
6-1
Static-Sensitive Devices................................................................................... 6-1
Precautions...................................................................................................... 6-1
Unpacking........................................................................................................ 6-1
6-2
Control Panel................................................................................................... 6-2
6-3
Removing the Chassis Cover.......................................................................... 6-3
6-4
System Fans.................................................................................................... 6-4
System Fan Failure.......................................................................................... 6-4
Replacing System Fans................................................................................... 6-4
Rear Exhaust Fans.......................................................................................... 6-4
6-5
Drive Bay Installation/Removal........................................................................ 6-5
Accessing the Drive Bays................................................................................ 6-5
SATA Drive Installation..................................................................................... 6-6
Hard Drive Backplane................................................................................. 6-7
Removing the Air Shroud................................................................................. 6-8
6-6
Power Supply................................................................................................... 6-9
Power Supply Failure....................................................................................... 6-9
6-7
Attaching a JBOD Expansion Chassis........................................................... 6-10
viii
ix
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
x
Chapter 1: Introduction
Chapter 1
Introduction
1-1Overview
The 6048R-E1CR24N is a high-end storage system comprised of two main subsystems: the SC846BE1C-R920B 4U/rackmount chassis and the X10DRi-T4+ dual
processor serverboard. Please refer to our website for information on operating
systems that have been certified for use with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 6048R-E1CR24N, as listed below:
•One active CPU heatsink (SNK-P0048AP4)
•One passive CPU heatsink (SNK-P0048P)
•Three 8-cm system fans (FAN-0127L4)
•Two 8-cm exhaust fans (FAN-0125L4)
•One air shroud (MCP-310-49003-0N)
•SATA accessories
One SAS3/SATA3 backplane (BPN-SAS3-846EL1)
Twenty-four drive carriers (MCP-220-00075-0B)
•Hardware RAID controller (AOC-S3108L-H8IR)
•JBOD expansion port (AOM-SAS3-8I8E-LP)
•One rackmount kit (MCP-290-00057-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
1-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
1-2 Serverboard Features
Chapter 1: Introduction
Rear I/O Ports
The 6048R-E1CR24N is built around the X10DRi-T4+, a dual processor serverboard
based on the Intel C612 chipset. Below are the main features of the X10DRi-T4+.
(See Figure 1-1 for a block diagram of the chipset.)
The I/O ports include one COM port, a VGA port, four USB (two USB 3.0 and two
USB 2.0), four 10G (TLAN) Ethernet ports and a dedicated IPMI LAN port.
1-3 Server Chassis Features
Processors
The X10DRi-T4+ supports single or dual Intel® Xeon E5-2600 (v3/v4) Series processors. Please refer to the serverboard description pages on our web site for a
complete listing of supported processors (www.supermicro.com).
The SC846BE1C-R920B is a 4U form factor chassis designed to be used in a
storage configuration. The following is a general outline of the main features of the
SC846BE1C-R920B chassis.
System Power
Memory
The X10DRi-T4+ has 24 DIMM slots that can support up to 3 TB of ECC LRDIMM
(Load Reduced DIMMs) or 1.5 TB of ECC RDIMM (Registered DIMMs) DDR42400/2133/1866/1600 memory. See Chapter 5 for details.
The SC846E16-R920B features a redundant (two separate power modules) 920W
high-efficiency power supply with I2C. This power redundancy feature allows you to
replace a failed power supply without shutting down the system.
Hard Drives
Main Storage Controller
An LSI 3108 controller card is included in the system to support up to 240 SATA
3.0/SAS 3.0 hard drives. (RAID 0, 1, 5, 6, 10, 50 and 60 supported). The SATA/
SAS drives are hot-swappable units.
Serial ATA
A SATA controller is also integrated into the chipset to provide 10 SATA 3.0 (6/Gbps)
ports (I-SATA0-5 supported by Intel PCH and S-SATA0-3 supported by Intel SCU),
which are RAID 0, 1 and 10 supported. The SATA drives are hot-swappable units.
RAID 5 supported with Windows OS only).
Note: The operating system you use must have RAID support to enable the hotswap capability and RAID function of the SATA drives.
PCI Expansion Slots
The X10DRi-T4+ has three PCI-Express 3.0 x8 slots (CPU2 Slot1/Slot2/Slot6), two
PCI-Express 3.0 x16 slots (CPU1 Slot3/ CPU2 Slot5) and one PCI-Express 2.0 x4
in x8 slot (CPU2 Slot4). With the RAID controller card and JBOD ports occupying
two of these slots, one PCI-E 3.0 x16 and three PCI-E 3.0 x8 expansion cards may
be added to the system
1-2
The SC846E16-R920B chassis was designed to support 24 SAS/SATA hard drives,
which are hot-swappable units.
Front Control Panel
The control panel provides you with system monitoring and control. LEDs indicate
system power, HDD activity, network activity, system overheat/fan fail and power
supply failure. A main power button and a system reset button are also included.
In addition, two USB ports and a COM port have been incorporated into the front
of the chassis for convenient access.
Cooling System
The SC846E16-R920B chassis includes three 8-cm hot-plug system cooling fans
located in the middle section of the chassis. Two additional 8-cm fans are located
at the back of the chassis to expel hot air from the system. An air shroud channels
the airflow from the system fans to efficiently cool the processors and memory. Each
power supply module also includes a cooling fan.
1-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 1: Introduction
1-4 Contacting Supermicro
Figure 1-1. Intel C612 Chipset:
System Block Diagram
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
Note: This is a general block diagram. Please see Chapter 5 for details.
PROCESSOR2
P0
9.6G
P1
PCI-E x8 SLOT 4
P0
D
B
PROCESSOR1
A
PE2 PE3 PE1 DM1
x16
x16
(15-0)
B#1
B#2
B#3
A#1
A #2
A#3
x16
6GB/s
Gen2 x4
DMI
USB 3.0
USB 3.0
x8 (0-7)
SYSTEM
BIOS
SPI
COM
PCI-E
USB 2.0
USB2.0 SPI LPC
Address:
USB 2.0
AST2400
VGA BMC
www.supermicro.com
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel:
+31 (0) 73-6400390
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
45
23
1
89
67
45
3
2
1
Website:
www.supermicro.nl
Asia-Pacific
Address:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
SPI
USB2.0
x8
DDR 3
LSI
3108
SATA
PCH 612
PCI-E X1 G2
I350/
X540/
SAGEVILL
LAN
Europe
USB
C
Website:
SATA #1
SATA #2
SATA #3
SATA #4
SATA #5
SATA #6
SATA #7
SATA #8
SATA #9
SATA #10
PCI-E x16 SLOT 3
G
P1
marketing@supermicro.com (General Information)
USB
E
x8 (8-15)
RJ45 RJ45
RJ45 RJ45
I350/
X540/
SAGEVILL
LAN
H
+1 (408) 503-8008
Email:
G#1
G#2
G #3
DDR4 DIMM
PE2 PE3 PE1 DM1
F
Fax:
support@supermicro.com (Technical Support)
H #1
H #2
H #3
DDR4 DIMM
DDR4 DIMM
x16
DDR4 DIMM
D #1
D #2
D #3
x16
Gen2 x4
DDR4 DIMM
DDR4 DIMM
C #1
C#2
C #3
x16
x8
QPI
DDR4 DIMM
F#1
F #2
F#3
DDR4 DIMM
E #1
E #2
E#3
x8
x8
+1 (408) 503-8000
QPI
(15-8)
PCI-E x8 SLOT 6
x8
PCI-E x16 SLOT 5
x8
(7-0)
PCI-E x8 SLOT 2
PCI-E x8 SLOT 1
San Jose, CA 95131 U.S.A.
Tel:
Taiwan (R.O.C)
TPM HDR
BMC BOOT FLASH
PHY1
VGA
CONN RTL8211
LAN
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
support@supermicro.com.tw
Website:
www.supermicro.com.tw
Note: The LSI 3108 onboard controller chip in the diagram above is not populated
on the X10DRi-T4+.
1-4
1-5
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
1-6
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1Overview
This chapter provides a quick setup checklist to get your SuperServer 6048RE1CR24N up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your system has come to you with the processors and memory
preinstalled. If your system is not already fully integrated with a serverboard, processors, system memory etc., please turn to the chapter or section noted in each
step for details on installing specific components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6048R-E1CR24N was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
file a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 6048RE1CR24N. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic fields are generated.
You will also need it placed near a grounded power outlet. Read the Rack and
Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6048R-E1CR24N was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.
•This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
2-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
•This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
Chapter 2: Server Installation
Rack Mounting Considerations
Ambient Operating Temperature
2-4 Warnings and Precautions
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Server Precautions
•Review the electrical and general safety precautions in Chapter 4.
•Determine the placement of each component in the rack before you install the
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
rails.
•Install the heaviest server components on the bottom of the rack first, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow any hot plug drives and power supply modules to cool before touching
them.
•Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
2-2
2-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 2: Server Installation
2-5 Installing the System into a Rack
Installing the Inner (Chassis) Rails
This section provides information on installing the S846 chassis into a rack unit with
Installing the Inner Rails
the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer
1. Extend the inner rail toward the front of the rail assembly as far as possible,
then depress the locking tab to pull it completely out.
to the installation instructions that came with the rack unit you are using.
2. Place the inner rail on the side of the chassis aligning the hooks of the chassis with the rail extension holes.
Separating the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fixed chassis rail that secures directly to
the server chassis and an outer fixed rack rail that secures directly to the rack itself.
3. Slide the extension toward the front of the chassis.
4. You may secure the chassis with screws if desired.
Separating the Inner and Outer Rails
5. Repeat steps 1-3 for the other inner rail.
1. Locate the rail assembly in the chassis packaging.
2. Extend the rail assembly by pulling it outward.
3. Press the quick-release tab.
4. Separate the inner rail extension from the outer rail assembly.
Figure 2-1. Separating the Rack Rails
1
F.
Rail Assembly
SCREW
12
Extending the Rails
12
13
2
13
Quick-Release
Tab
1
Figure 2-2. Installing the Inner Rails
Note: 3U system shown above, rails are common to the SC846 also.
14
Separating the Inner
Rail Extension
2-4
Warning: do not pick up the server with the front handles. They are designed to pull the system from a rack only.
2-5
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Installing the Outer (Rack) Rails
Outer rails attach to the server rack and hold the server in place. The outer rails
for the chassis extend between 30 inches and 33 inches.
Installing the Outer Rails
1. Attach the right outer rail to the rack by inserting the hooks included on the
rails into the holes provided on the rack.
2. If desired, screw the rails to the chassis for added support.
3. Repeat these steps for the left outer rail.
Chapter 2: Server Installation
Installing the Sytem into a Rack
Installing into a Rack
1. Confirm that the inner and outer rails are properly installed.
2. Line up the inner (chassis) rails with the front of the outer (rack) rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into position.
4. (Optional) Insert and tighten the thumbscrews that hold the front of the server
to the rack.
Warning: Slide rail mounted equipment is not to be used as a shelf or a
work space.
Figure 2-3. Outer Rails
Warning: In any instance of pulling the system from the rack, always use
a rack lift and follow all associated safety precautions.
Warning: Stability hazard. The rack stabilizing mechanism must be in
place, or the rack must be bolted to the floor before you slide the unit out
for servicing. Failure to stabilize the rack can cause the rack to tip over.
Figure 2-4. Installing the Outer Rails
Warning: When initially installing the server to a rack, test that the rail
locking tabs engage to prevent the server from being overextended. Have
a rack lift in place as a precaution in case the test fails.
2-6
2-7
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
1B
1A
Figure 2-5. Installing the Rack Rails
Installing the Chassis into a Rack
Installing the Chassis into a Rack
1. Confirm that chassis includes the inner rails (A), also confirm that the outer
rails (B) are installed on the rack.
2. Align chassis rails (A) with the front of the rack rails (B).
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into the locked position.
4. Tighten up all the screws on the front side and rear side of both outer rails.
5. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
2-8
Chapter 3: System Interface
Chapter 3
System Interface
3-1Overview
There are several LEDs on the control panel as well as others on the hard drive
carriers to keep you constantly informed of the overall status of the system as well
as the activity and health of specific components. There are also two buttons on
the chassis control panel.
3-2 Control Panel Buttons
The two push-buttons located on the front of the chassis are (in order from left to
right) a reset button and a power on/off button.
Reset
Use the reset button to reboot the system.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system. Therefore, the system power cord should
be unplugged before performing service.
3-3 Control Panel LEDs
The control panel located on the front of the chassis has several LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.
3-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 3: System Interface
2
NIC2
Power Fail
Indicates a power supply module has failed. The second power supply module will
take the load and keep the system running but the failed module will need to be
replaced. Refer to Chapter 6 for details on replacing the power supply. This LED
should be off when the system is operating normally.
Indicates network activity on the LAN2 port when flashing.
HDD
Indicates IDE channel activity. On the SuperServer 6048R-E1CR24N, this LED
indicates hard and/or DVD-ROM drive activity when flashing.
Information LED
The Information LED provides alerts for several states, as noted in the table below.
Information LED
Status
Description
Continuously on and red
An overheat condition has occured.
(This may be caused by cable congestion.)
Blinking red (1Hz)
Fan failure, check for an inoperative fan.
Blinking red (0.25Hz)
Power failure, check for a non-operational power supply.
Solid blue
Local UID has been activated. Use this function to locate
the server in a rack mount environment.
Blinking blue
Remote UID is on. Use this function to identify the
server from a remote location.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.
3-4 Drive Carrier LEDs
Each drive carrier has two LEDs.
•Blue: When illuminated, the blue LED on the front of the drive carrier indicates
drive activity. A connection to the backplane enables this LED to blink on and
off when that particular drive is being accessed.
•Red: The SAF-TE compliant backplane activates the red LED to indicate a
1
NIC1
Indicates network activity on the LAN1 port when flashing.
3-2
drive failure. If one of the drives fail, you should be notified by your system
management software. Please refer to Chapter 6 for instructions on replacing
failed drives.
3-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
3-4
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certified technicians should attempt to install or configure
components.
Read this appendix in its entirety before installing or configuring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Definition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分
意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸
電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。
4-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Warning Statements for AC Systems
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
. ‫تحذٌز!هذا الزهز ٌعًٌ خطز اًك فً حالة ٌوكي أى تتسبب فً اصابة جسذٌة‬
‫كي على علن بالوخاطز الٌاجوة عي الذوائز‬،‫قبل أى تعول على أي هعذات‬
‫الكهزبائٍة‬
‫وكي على دراٌة بالووارسات الىقائٍة لوٌع وقىع أي حىادث‬
‫استخذم رقن البٍاى الوٌصىص فً ًهاٌة كل تحذٌز للعثىر تزجوتها‬
안전을 위한 주의사항
BEWAHREN SIE DIESE HINWEISE GUT AUF.
경고!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
final de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
GUARDE ESTAS INSTRUCCIONES.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
IMPORTANTES INFORMATIONS DE SÉCURITÉ
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
CONSERVEZ CES INFORMATIONS.
‫תקנון הצהרות אזהרה‬
‫ על מנת להזהיר את המשתמש מפני חבלה‬,‫הצהרות הבאות הן אזהרות על פי תקני התעשייה‬
‫ יש ליצור קשר עם מחלקת תמיכה‬,‫ במידה ויש שאלות או היתקלות בבעיה כלשהי‬.‫פיזית אפשרית‬
.‫ טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים‬.‫טכנית של סופרמיקרו‬
.‫יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו‬
4-2
4-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Installation Instructions
Chapter 4: Warning Statements for AC Systems
Circuit Breaker
Warning!
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
システムを電源に接続する前に、設置手順書をお読み下さい。
この製品は、短絡(過電流)保護装置がある建物での設置を前提としています。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前,請先閱讀安裝說明。
Warnung
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。
¡Advertencia!
Warnung
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschlussbzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
.‫יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח‬
‫اقر إرشادات التركيب قبل توصيل النظام إلى مصدر للطاقة‬
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
4-4
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vérifiez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
‫ יש לוודא כי‬.‫מוצר זה מסתמך על הגנה המותקנת במבנים למניעת קצר חשמלי‬
60VDC, 20A-‫המכשיר המגן מפני הקצר החשמלי הוא לא יותר מ‬
‫هذا المنتج يعتمد على معداث الحمايت مه الدوائرالقصيرة التي تم تثبيتها في‬
‫المبنى‬
20A, 250VDC :‫تأكد من أن تقييم الجهاز الوقائي ليس أكثر من‬
4-5
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 4: Warning Statements for AC Systems
경고!
¡Advertencia!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Attention
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、
シャーシー内部にアクセス
するには、
Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.
‫אזהרה מפני ניתוק חשמלי‬
!‫אזהרה‬
‫יש לנתק את המערכת מכל מקורות החשמל ויש להסיר את כבל החשמלי מהספק‬
.‫לפני גישה לחלק הפנימי של המארז לצורך התקנת או הסרת רכיבים‬
‫يجب فصم اننظاو من جميع مصادر انطاقت وإزانت سهك انكهرباء من وحدة امداد‬
‫انطاقت قبم‬
‫انىصىل إنى انمناطق انداخهيت نههيكم نتثبيج أو إزانت مكىناث الجهاز‬
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
경고!
警告
시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
Waarschuwing
警告
在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。
Warnung
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.
4-6
4-7
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Equipment Installation
Chapter 4: Warning Statements for AC Systems
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalificeerd personeel.
Warning!
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.
Restricted Area
Warning!
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、
またはサービスを許可
されています。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、
アクセス制限区域に設置されることを想定しています。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。
Warnung
警告
此部件应安装在限制进出的场所,限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
警告
此裝置僅限安裝於進出管制區域,進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。
Warnung
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifiés et expérimentés.
!‫אזהרה‬
.‫ להחליף את הציוד או לתת שירות עבור הציוד‬,‫צוות מוסמך בלבד רשאי להתקין‬
‫يجب أن يسمح فقط للمىظفيه المؤهليه والمدربيه لتزكيب واستبدال أو خدمة هذا الجهاس‬
경고!
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.
4-8
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
4-9
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
‫אזור עם גישה מוגבלת‬
!‫אזהרה‬
‫ הגישה ניתנת בעזרת‬.‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה‬
.)'‫ מנעול וכד‬,‫כלי אבטחה בלבד (מפתח‬
Chapter 4: Warning Statements for AC Systems
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
. ‫تم تخصيص هذه انىحذة نتركُبها فٍ مناطق محظورة‬
،‫َمكن انىصىل إنً منطقت محظورة فقط من خالل استخذاو أداة خاصت‬
‫قفم ومفتاح أو أٌ وسُهت أخري نالمألما‬
경고!
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
Battery Handling
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
‫هناك خطر من انفجار في حالة اسحبذال البطارية بطريقة غير صحيحة فعليل‬
‫اسحبذال البطارية‬
‫فقط بنفس النىع أو ما يعادلها مما أوصث به الشرمة المصنعة‬
‫جخلص من البطاريات المسحعملة وفقا لحعليمات الشرمة الصانعة‬
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
4-10
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
4-11
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 4: Warning Statements for AC Systems
Redundant Power Supplies
경고!
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。
.‫قد يكون لهذا الجهاز عدة اتصاالت بوحدات امداد الطاقة‬
‫يجب إزالة كافة االتصاالت لعسل الوحدة عن الكهرباء‬
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
バックプレーンの電圧
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。
警告
當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。
Attention
Warnung
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
‫אם קיים יותר מספק אחד‬
!‫אזהרה‬
‫ יש להסיר את כל החיבורים על מנת לרוקן‬.‫ליחדה יש יותר מחיבור אחד של ספק‬
.‫את היחידה‬
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.
4-12
4-13
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 4: Warning Statements for AC Systems
‫מתח בפנל האחורי‬
!‫אזהרה‬
‫ יש להיזהר במהלך‬.‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת‬
.‫העבודה‬
‫هناك خطز مه التيار الكهزبائي أوالطاقة المىجىدة على اللىحة‬
‫عندما يكىن النظام يعمل كه حذرا عند خدمة هذا الجهاس‬
Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
‫תיאום חוקי החשמל הארצי‬
!‫אזהרה‬
.‫התקנת הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬
‫تركيب المعدات الكهربائية يجب أن يمتثل للقىاويه المحلية والىطىية المتعلقة‬
‫بالكهرباء‬
경고!
시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Comply with Local and National Electrical Codes
Warning!
Installation of the equipment must comply with local and national electrical codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
警告
设备安装必须符合本地与本国电气法规。
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
¡Advertencia!
Warnung
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
4-14
4-15
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 4: Warning Statements for AC Systems
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
警告
當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
‫عند التخلص النهائي من هذا المنتج ينبغي التعامل معه وفقا لجميع القىانين واللىائح الىطنية‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Hot Swap Fan Warning
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
!‫אזהרה‬
‫ יש‬.‫ יתכן והמאווררים עדיין עובדים‬,‫כאשר מסירים את חלקי המאוורר מהמארז‬
‫להרחיק למרחק בטוח את האצבעות וכלי עבודה שונים מהפתחים בתוך המאוורר‬
‫مه انممكه أن انمراوح ال تسال تدورعند إزانة كتهة انمروحة مه انهيكم يجب إبقاء‬
‫األصابع ومفكات انبراغي‬
.‫وغيرها مه األشياء بعيدا عه انفتحات في كتهة انمروحة‬
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep fingers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
ファン・ホットスワップの警告
シャーシから冷却ファン装置を取り外した際、
ファンがまだ回転している可能性がありま
す。ファンの開口部に、指、
ドライバー、およびその他のものを近づけないで下さい。
警告
当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
4-16
경고!
섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.
Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.
4-17
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Power Cable and AC Adapter
Chapter 4: Warning Statements for AC Systems
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
Warning!
When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.
電源コードとACアダプター
製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ
ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表
記)を Supermicroが指定する製品以外に使用することを禁止しています。
警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。
Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certificados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
4-18
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
AC
‫חשמליים ומתאמי‬
!‫אזהרה‬
‫ אשר‬AC ‫ ספקים ומתאמים‬,‫ יש להשתמש בכבלים‬,‫כאשר מתקינים את המוצר‬
‫ שימוש בכל כבל או מתאם אחר יכול לגרום לתקלה או‬.‫נועדו וסופקו לשם כך‬
‫ קיים איסור‬,‫ על פי חוקי שימוש במכשירי חשמל וחוקי בטיחות‬.‫קצר חשמלי‬
‫ (כשאר מופיע עליהם קוד של‬CSA -‫ או ב‬UL -‫להשתמש בכבלים המוסמכים ב‬
.‫) עבור כל מוצר חשמלי אחר שלא צוין על ידי סופרקמיקרו בלבד‬UL/CSA
‫والكابالث الكهربائيت‬،‫عىذ تركيب الجهاز يجب استخذام كابالث التىصيل‬
‫ومحىالث التيار المتردد‬
.‫ أن استخذام أي كابالث ومحىالث أخري يتسبب في حذوث عطل أو حريق‬. ‫التي‬
‫تم تىفيرها لك مع المىتج‬
UL ‫ أو‬CSA ‫األجهسة الكهربائيت ومىاد قاوىن السالمت يحظر استخذام الكابالث‬
‫معتمذة مه قبل‬
Supermicro ‫ألي أجهسة كهربائيت أخري غير المىتجاث المعيىت مه قبل‬
(UL/CSA ‫)التي تحمل عالمت‬
경고!
제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
4-19
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
4-20
Chapter 5: Advanced Serverboard Setup
Chapter 5
Advanced Serverboard Setup
This chapter covers the steps required to connect the data and power cables and
install add-on cards. All serverboard jumpers and connections are also described.
A layout and quick reference chart are included in this chapter for your reference.
Remember to completely close the chassis when you have finished working with
the serverboard to better cool and protect the system.
5-1 Handling the Serverboard
Electrostatic Discharge (ESD) can damage electronic com­ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully
(see previous chapter). To prevent the serverboard from bending, keep one hand
under the center of the board to support it when handling. The following measures
are generally sufficient to protect your equipment from electric static discharge.
Precautions
•Use
a grounded wrist strap designed to prevent Electrostatic Discharge
(ESD).
•Touch a grounded metal object before removing any board from its antistatic
bag.
•Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
•For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
5-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-2 Connecting Cables
Figure 5-1. Control Panel Header Pins
20
Several cables need to be connected to the serverboard. These include the data
cables for the peripherals and control panel and the power cables.
19
Ground
NMI
x (Key)
x (Key)
Power On LED
Connecting Data Cables
HDD LED
The cables used to transfer data from the peripheral devices have been carefully
routed to prevent them from blocking the flow of cooling air that moves through
the system from front to back. If you need to disconnect any of these cables, you
should take care to keep them routed as they were originally after reconnecting
them (make sure the red wires connect to the pin 1 locations). See the layout on
page 5-10 for connector locations.
ID/UID/SW/3.3V Stby
NIC1 Link LED
NIC1 Activity LED
NIC2 Link LED
NIC2 Activity LED
OH/Fan Fail LED
Red + (Blue Cathode
Power Fail LED
3.3V
Ground
Reset (Button)
Ground
Connecting Power Cables
The X10DRi-T4+ has a 24-pin primary power supply connector (J24) for connection to the ATX power supply. In addition, there are two 8-pin 12V processor power
connectors (JPWR1 and JPWR2) that must be connected to your power supply.
See Section 5-9 for power connector pin definitions.
3.3V
Power (Button)
2
1
5-3 Rear I/O Ports
See Figure 5-2 below for the colors and locations of the various I/O ports.
Connecting the Control Panel
Figure 5-2. Rear I/O Ports
JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
4
All JF1 wires have been bundled into a single cable to simplify this connection. Make
sure the red wire plugs into pin 1 as marked on the board. The other end connects
to the Control Panel PCB board, located just behind the system status LEDs on
the chassis. See Chapter 5 for details and pin descriptions.
1
3
6
2
5
18
110
7
9
Rear I/O Ports
5-2
1
COM Port 1
7
TLAN Port 1
2
USB Port 0
8
TLAN Port 2
3
USB Port 1
9
TLAN Port 3
4
Dedicated IPMI LAN
10
TLAN Port 4
5
USB Port 4
11
VGA Port
6
USB Port 5
12
UID Switch
5-3
111
112
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-4 Installing the Processor and Heatsink
Warning: When handling the processor package, avoid placing direct pressure on the
label area of the fan.
Notes:
Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.
•
•If you buy a CPU separately, make sure that you use an Intel-certified multidirectional heatsink only.
•Make sure to install the serverboard into the chassis before you install the CPU
heatsinks.
•When receiving a serverboard without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.
•Refer to the Supermicro web site for updates on CPU support.
Installing an LGA2011 Processor
Press down on the lever labeled
'Close 1st'
1. There are two levers on the
LGA2011 socket. First press and
release the load lever labeled
'Open 1st'.
WA
R
NI
OP
2. Press the second load lever
labeled 'Close 1st' to release the
load plate from its locked position.
EN
NG
3. With the lever labeled 'Close 1st'
fully retracted, gently push down
on the 'Open 1st' lever to open the
load plate. Lift the load plate to
open it completely.
NI
OP
EN
NG
!
1st
Gently push
down to pop
the load plate
open.
4. Using your thumb and the index
finger, remove the 'WARNING'
plastic cap from the socket.
5. Use your thumb and index finger
to hold the CPU by its edges. Align
the CPU keys, which are semicircle cutouts, against the socket
keys.
WA
R
NI
NG
!
6. Once they are aligned, carefully
lower the CPU straight down into
the socket. (Do not drop the CPU
on the socket. Do not move the
CPU horizontally or vertically and
do not rub the CPU against any
pins of the socket, which may
damage the CPU or the socket.)
Socket Keys
!
1st
CPU Keys
Pull lever away
from the socket
WA
R
NI
OP
EN
5-4
WA
R
NG
!
1st
5-5
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
Warning: You can only install the CPU to the socket in one direction. Make sure that
the CPU is properly inserted into the socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.
Installing a CPU Heatsink
1. Do not apply any thermal grease to the heatsink or the CPU die. The required
amount has already been applied.
2. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the serverboard and the heatsink bracket underneath.
7. With the CPU in the socket, inspect the four corners of the CPU
to make sure that they are flush
with the socket.
8. Close the load plate. Lock the
lever labeled 'Close 1st', then lock
the lever labeled 'Open 1st'. Use
your thumb to gently push the
load levers down until the lever
locks.
3. Screw in two diagonal screws (i.e., the #1 and the #2 screws) until just snug
(do not over-tighten the screws to avoid possible damage to the CPU.)
Gently close
the load plate.
4. Finish the installation by fully tightening all four screws.
Figure 5-3. Installing a Heatsink
Screw #1
(behind)
Screw#1
Push down and lock the
level labeled 'Close 1st'.
#4
#3
OP
EN
Screw #4
#2
1st
SNK-P0048AP4
SNK-P0048P
Screw #3
Screw #2
Removing the Heatsink
Warning: We do not recommend that the CPU or the heatsink be removed. However,
if you do need to uninstall the heatsink, please follow the instructions below to uninstall
the heatsink to prevent damage to the CPU or the CPU socket.
Lever Lock
1. Unscrew the heatsink screws in the sequence as shown above.
OP
2. Gently wriggle the heatsink to loosen it from the CPU. (Do not use excessive
force when wriggling the heatsink!)
EN
1st
Push down
and lock the
lever labeled
'Open 1st'.
3. Once the heatsink is loose, remove it from the CPU.
4. Remove the used thermal grease and clean the surface of the CPU and the
heatsink, Reapply the proper amount of thermal grease on the surface before
reinstalling the heatsink.
Warning: Do not reuse old thermal grease!
5-6
5-7
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
5-5 Installing Memory
Chapter 5: Advanced Serverboard Setup
Processor & Memory Module Population Configuration
For memory to work properly, follow the tables below for memory installation.
Caution: Exercise extreme care when installing or removing DIMM modules to prevent
Processors and their Corresponding Memory Modules
any possible damage.
CPU#
Memory Support
Corresponding DIMM Modules
CPU1
The X10DRi-T4+ supports up to 3 TB of ECC LRDIMM (Load Reduced DIMMs) or
1.5 TB of ECC RDIMM (Registered DIMMs) DDR4-2400/2133/1866/1600 memory.
For best performance, install pairs of memory modules of the same type and speed.
Please refer to our website for any updates to supported memory. All channels will
run at the fastest common frequency.
P1-DIMM-
Installing Memory Modules
1. Insert the desired number of DIMMs into the memory slots starting with P1DIMM1A. See the Memory Installation Tables on the following pages.
2. Insert each DIMM module vertically into its slot. Pay attention to the notch
along the bottom of the module to avoid installing incorrectly (see Figure 5-3).
3. Use your thumbs to gently press down on both ends of the DIMM module
until it snaps into place in the slot. Repeat for all modules.
4. Press the release tabs to the locked positions to secure the DIMM module
into the slot.
B1
C1
D1
E1
F1
G1
H1
CPU2
P2-DIMM-
A2
B2
C2
D2
A3
B3
C3
D3
E3
F3
G3
H3
P2-DIMME1~P1-DIMMH3
E2
F2
G2
H2
Processor and Memory Module Population for Optimal Performance
Number of
CPUs+DIMMs
DIMM Installation
P1-DIMMA1~P1-DIMMD3
A1
CPU and Memory Population Configuration Table
(For memory to work properly, please follow the instructions below.)
1 CPU &
2 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
1 CPU &
5~8 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
2 CPUs &
4 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs &
8 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1
2 CPUs &
9~16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots
2 CPUs &
16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/
P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
2 CPUs &
16~24 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1, P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/
P2-DIMMF2/P2-DIMMG2/P2-DIMMH2, P1-DIMMA3/P1-DIMMB3/P1-DIMMC3/P1DIMMD3, P2-DIMME3/P2-DIMMF3/P2-DIMMG3/P2-DIMMH3
Figure 5-4. DIMM Installation
Note: see layout diagrams on following page, which display the order of populating DIMMs.
Release Tab
Socket Key
Release Tab
5-8
5-9
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
1 CPU, 4 DIMMs
1 CPU, 5-8 DIMMs
JPI2C1
FAN5
JPP1
JPP0
JSTBY1
J24
JPWR2
JPWR1
Populating RDIMM/LRDIMM DDR4 Memory Modules
FAN1
J24
JPWR2
JPWR1
JPP1
JPP0
FAN1
JPI2C1
FAN5
JSTBY1
1
J24
JPWR2
JPWR1
1
JPP1
JPP0
FAN1
JPI2C1
JSTBY1
1
1 CPU, 2 DIMMs
FAN5
Chapter 5: Advanced Serverboard Setup
TPM/PORT80
I-SATA5
SAN MAC
BIOS
LICENSE
TPM/PORT80
USB2/3
OPEN 1st
JI2C1
JI2C2
LEDS5
LEDS6
SAS 0~3 (3.0)
JS39
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
I-SATA5
I-SATA3 I-SATA1
JD1
JPS7
JL1
I-SATA0
USB 7/8 (3.0)
JS1
USB 7/8 (3.0)
TPM/PORT80
E5-2600 V4
E5-2600 V3
E5-2600 V4
4 Gb
8 Gb
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
SRx4
8 GB
16 GB
2133
2400
1866
2133
1600
1600
RDIMM
SRx8
4 GB
8 GB
2133
2400
1866
2133
1600
1600
RDIMM
DRx8
8 GB
16 GB
2133
2400
1866
2133
1600
1600
RDIMM
DRx4
16 GB
32 GB
2133
2400
1866
2133
1600
1600
LRDIMM
QRx4
32 GB
64 GB
2133
2400
2133
2400
1600
1866
64 GB
128
GB
2133
2400
2133
2400
1600
1866
8Rx4
FAN1
1
OPEN 1st
LE2
JF1
Front CTRL Panel
IPMI CODE
SAS CODE
JSTBY1
FAN2
CPU1
OPEN 1st
X10DRC/i-LN4+(-T4+)
CPU2
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
Rev. 1.01
USB 0/1
USB4/5
(3.0)
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
FAN3
SAN MAC
LE1
I-SATA5
I-SATA0
USB 7/8 (3.0)
BIOS
LICENSE
SP1
BAR CODE
MAC CODE
FAN4
JPS1
DS13
FANC
JS1
USB 6 (3.0)
COM2
LSI 3108
SAS CTRL
Intel PCH
JBAT1
JTPM1
TPM/PORT80
USB2/3
S-SATA1 S-SATA0
JI2C1
JI2C2
JBT1
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
LEDS5
LEDS6
JD1
JPS7
JL1
I-SATA2
I-SATA3 I-SATA1
5-6 Adding PCI Add-On Cards
SAS 4~7 (3.0)
I-SATA4
I-SATA5
FANA
SAS 0~3 (3.0)
JS39
BIOS
JPB1
JSD1
JWD1
JPME2
JS39
CPU2 SLOT1 PCI-E 3.0 X8
JD1
JPS7
JL1
LEDM1
LSI 3108
SAS CTRL
LAN CTRL
JPLAN1
JPG1
SAS 4~7 (3.0)
I-SATA2
I-SATA3 I-SATA1
CPU1 SLOT3 PCI-E 3.0 X16
CPU2 SLOT2 PCI-E 3.0 X8
SAS 0~3 (3.0)
I-SATA4
S-SATA1 S-SATA0
JPLAN2
FANA
BMC
SP1
LEDS5
LEDS6
CPU2 SLOT5 PCI-E 3.0 X16
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
Intel PCH
JBT1
JI2C1
JI2C2
JSD1
JWD1
JPME2
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
LAN CTRL
BIOS
LICENSE
BAR CODE
MAC CODE
JBAT1
BIOS
BMC
JTPM1
COM2
E5-2600 V3
JUIDB1
VGA
UID
SAN MAC
FANC USB 6 (3.0)
JS1
USB2/3
J24
JPWR2
JPWR1
I-SATA0
USB 7/8 (3.0)
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
I-SATA0
LEDM1
LAN CTRL
LSI 3108
SAS CTRL
I-SATA3 I-SATA1
FAN4
JPS1
DS13
JIPMB1
I-SATA5
CPU2 SLOT1 PCI-E 3.0 X8
JD1
JPS7
JL1
I-SATA2
3 DPC
E5-2600 V4
CPU2 SLOT6 PCI-E 3.0 X8
JPB1
JPG1
SAS 4~7 (3.0)
I-SATA4
S-SATA1 S-SATA0
JPLAN1
CPU2 SLOT2 PCI-E 3.0 X8
JS39
JBT1
SAS 0~3 (3.0)
CPU1 SLOT3 PCI-E 3.0 X16
CLOSE 1st
COM1
IPMI_LAN
LAN1/2
LAN3/4
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
FAN3
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
TPM/PORT80
LEDS5
LEDS6
JPLAN2
JIPMB1
JTPM1
COM2
USB2/3
JI2C1
JI2C2
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
BMC
CPU2 SLOT1 PCI-E 3.0 X8
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
JSD1
JWD1
JPME2
JPB1
JPG1
CPU2 SLOT5 PCI-E 3.0 X16
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
FANA
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
CLOSE 1st
FAN1
1
OPEN 1st
Front CTRL Panel
CPU1
IPMI CODE
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
SAS CODE
FAN2
LE2
JF1
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
Rev. 1.01
CPU2
USB4/5
(3.0)
LE1
SP1
Intel PCH
JBAT1
LEDM1
JPLAN1
CPU2 SLOT2 PCI-E 3.0 X8
FAN4
JPS1
DS13
BIOS
CPU1 SLOT3 PCI-E 3.0 X16
LAN CTRL
BIOS
LICENSE
BAR CODE
JPLAN2
JIPMB1
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
CPU2 SLOT6 PCI-E 3.0 X8
CPU2 SLOT5 PCI-E 3.0 X16
MAC CODE
LAN CTRL
LAN CTRL
JPP1
JPP0
JUIDB1
VGA
UID
SAN MAC
LE1
USB 0/1
IPMI_LAN
LAN3/4
Front CTRL Panel
LAN1/2
OPEN 1st
CPU1
IPMI CODE
FAN3
JUIDB1
VGA
SAS CODE
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
JPI2C1
FAN5
JSTBY1
FAN6
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
CPU2 SLOT6 PCI-E 3.0 X8
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
FANC USB 6 (3.0)
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
CLOSE 1st
COM1
1
FAN2
LE2
JF1
J24
JPWR2
JPWR1
JPP1
JPP0
2 DPC
E5-2600 V3
2 CPUs, 8 DIMMs
JPI2C1
FAN5
JSTBY1
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
Rev. 1.01
CPU2
LAN1/2
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
LAN3/4
J24
JPWR2
JPWR1
FAN6
USB4/5
(3.0)
USB 0/1
IPMI_LAN
FAN6
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
CLOSE 1st
COM1
JPP1
JPP0
FAN1
JPI2C1
FAN5
UID
2 CPUs, 6 DIMMs
1 DPC
RDIMM
LRDIMM
3DS
2 CPUs, 4 DIMMs
3 Slots per Channel
DIMM Capacity
(GB)
SAS 4~7 (3.0)
I-SATA2
I-SATA4
S-SATA1 S-SATA0
FANA
LSI 3108
SAS CTRL
Intel PCH
JBAT1
SP1
BAR CODE
MAC CODE
FAN4
JPS1
BIOS
BMC
JTPM1
COM2
Ranks
Per
DIMM
and
Data
Width
DS13
JBT1
JS39
USB 7/8 (3.0)
FANC USB 6 (3.0)
JS1
Front CTRL Panel
8
JPB1
JPG1
CPU2 SLOT1 PCI-E 3.0 X8
JD1
JPS7
JL1
I-SATA0
LEDM1
LAN CTRL
LSI 3108
SAS CTRL
I-SATA3 I-SATA1
JPLAN1
CPU2 SLOT2 PCI-E 3.0 X8
SAS 4~7 (3.0)
I-SATA2
I-SATA4
S-SATA1 S-SATA0
CPU1 SLOT3 PCI-E 3.0 X16
Type
FAN3
7
JUIDB1
LE1
SP1
Intel PCH
JI2C1
JI2C2
JBT1
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
CPU1
IPMI CODE
SAS CODE
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
JSD1
JWD1
JPME2
USB2/3
LAN CTRL
BIOS
LICENSE
BAR CODE
MAC CODE
JBAT1
BIOS
JTPM1
COM2
JPLAN2
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
FANA
SAS 0~3 (3.0)
FAN2
LE2
JF1
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
Rev. 1.01
USB 0/1
USB4/5
(3.0)
CPU2
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
FANC USB 6 (3.0)
JS1
LEDS5
LEDS6
CPU2 SLOT5 PCI-E 3.0 X16
JIPMB1
USB 7/8 (3.0)
LEDM1
LAN CTRL
LSI 3108
SAS CTRL
I-SATA0
I-SATA3 I-SATA1
CPU2 SLOT1 PCI-E 3.0 X8
JD1
JPS7
JL1
FAN4
JPS1
DS13
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
I-SATA5
JPB1
JPG1
SAS 4~7 (3.0)
I-SATA2
I-SATA4
S-SATA1 S-SATA0
JPLAN1
CPU2 SLOT2 PCI-E 3.0 X8
BMC
JI2C1
JI2C2
CPU1 SLOT3 PCI-E 3.0 X16
JS39
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
CLOSE 1st
COM1
IPMI_LAN
LAN3/4
VGA
UID
SAN MAC
LE1
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
FAN3
Speed (MT/s); Voltage (V); Slots per Channel (SPC) and DIMMs per Channel (DPC)
6
LAN1/2
OPEN 1st
Front CTRL Panel
CPU1
IPMI CODE
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
Rev. 1.01
USB 0/1
USB4/5
(3.0)
CPU2
SAS CODE
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
JSD1
JWD1
JPME2
USB2/3
JPLAN2
JIPMB1
TPM/PORT80
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
CPU2 SLOT6 PCI-E 3.0 X8
CPU2 SLOT5 PCI-E 3.0 X16
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
FANA
SAS 0~3 (3.0)
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
BMC
JTPM1
COM2
LAN CTRL
SP1
JPB1
JPG1
CPU2 SLOT1 PCI-E 3.0 X8
LEDS5
LEDS6
JBT1
CPU2 SLOT2 PCI-E 3.0 X8
JSD1
JWD1
JPME2
LEDM1
JPLAN1
BIOS
CPU1 SLOT3 PCI-E 3.0 X16
FAN4
JPS1
DS13
Intel PCH
JBAT1
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
JIPMB1
FAN2
LE2
JF1
JUIDB1
VGA
UID
SAN MAC
BIOS
LICENSE
BAR CODE
JPLAN2
MAC CODE
LAN CTRL
CLOSE 1st
COM1
FAN3
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
CPU2 SLOT6 PCI-E 3.0 X8
CPU2 SLOT5 PCI-E 3.0 X16
LAN CTRL
FAN6
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
LAN3/4
Front CTRL Panel
IPMI CODE
SAS CODE
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
CPU2 SLOT6 PCI-E 3.0 X8
FANC USB 6 (3.0)
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
LAN1/2
OPEN 1st
LE2
JF1
JUIDB1
VGA
IPMI_LAN
FAN2
CPU1
CPU2
CLOSE 1st
LAN1/2
LAN3/4
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
LE1
UID
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
FAN6
USB4/5
(3.0)
USB 0/1
IPMI_LAN
FAN6
Rev. 1.01
COM1
5
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
JS1
The 6048R-E1CR24N can accommodate up to four PCI add-on (expansion) cards.
Note that two of the PCI slots (slots 3 and 4) are occupied by the RAID controller
and the JBOD expansion port.
One PCI-E 3.0 x16 and three PCI-E 3.0 x8 cards may be added to the system.
Installing an Add-on Card
USB2/3
S-SATA1 S-SATA0
USB 7/8 (3.0)
COM2
FAN1
1
OPEN 1st
SP1
Intel PCH
JBAT1
DS13
LSI 3108
SAS CTRL
BIOS
LICENSE
FAN4
JPS1
USB2/3
S-SATA1 S-SATA0
JI2C1
JI2C2
LEDS5
LEDS6
SAS 4~7 (3.0)
JD1
JPS7
JL1
I-SATA2
I-SATA4
I-SATA5
5-10
I-SATA3 I-SATA1
FANA
SAS 0~3 (3.0)
JS39
BIOS
LEDM1
JTPM1
TPM/PORT80
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
2. Fully seat the card into the slot, pushing down with your thumbs evenly on
both sides of the card.
FAN3
11
20
MAC CODE
BAR CODE
Front CTRL Panel
CPU1
IPMI CODE
SAS CODE
SAN MAC
FANC USB 6 (3.0)
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
12
19
JPB1
BMC
JPG1
CPU2 SLOT1 PCI-E 3.0 X8
JS1
FAN2
LE2
JF1
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
CPU2
Rev. 1.01
USB 0/1
USB4/5
(3.0)
LE1
JUIDB1
LAN CTRL
LAN CTRL
LSI 3108
SAS CTRL
JD1
JPS7
JL1
I-SATA0
JPLAN1
CPU2 SLOT2 PCI-E 3.0 X8
SAS 4~7 (3.0)
I-SATA2
I-SATA3 I-SATA1
CPU1 SLOT3 PCI-E 3.0 X16
JS39
JBT1
JI2C1
JI2C2
I-SATA4
I-SATA5
CLOSE 1st
COM1
IPMI_LAN
LAN1/2
VGA
UID
SP1
Intel PCH
JBAT1
LEDM1
JTPM1
TPM/PORT80
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
JPLAN2
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
FANA
SAS 0~3 (3.0)
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
I-SATA0
USB 7/8 (3.0)
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
COM2
JPB1
LEDS5
LEDS6
CPU2 SLOT5 PCI-E 3.0 X16
JIPMB1
JIPMB1
FANC USB 6 (3.0)
DS13
JSD1
JWD1
JPME2
JPG1
CPU2 SLOT1 PCI-E 3.0 X8
BMC
JPLAN1
BIOS
CPU1 SLOT3 PCI-E 3.0 X16
CPU2 SLOT2 PCI-E 3.0 X8
CPU2 SLOT6 PCI-E 3.0 X8
FAN4
JPS1
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
SAN MAC
BIOS
LICENSE
BAR CODE
JPLAN2
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
21
13
11
MAC CODE
CPU2 SLOT5 PCI-E 3.0 X16
22
14
FAN3
10
18
P1-DIMMA1
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
1. Begin by removing the shield for the PCI slot you wish to populate.
JSTBY1
9
17
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
LAN3/4
Front CTRL Panel
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
J24
JPWR2
JPWR1
JPP1
JPP0
JBT1
FAN1
OPEN 1st
CPU1
CLOSE 1st
OPEN 1st
X10DRC/i-LN4+(-T4+)
SAS CODE
VGA
UID
JUIDB1
CPU2 SLOT6 PCI-E 3.0 X8
LAN CTRL
LE2
JF1
12
13
LAN CTRL
FAN2
IPMI CODE
LAN3/4
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
14
16
24
FAN6
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
Rev. 1.01
CPU2
LAN1/2
CLOSE 1st
COM1
10
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
JPI2C1
FAN5
15
23
JSTBY1
9
USB4/5
(3.0)
USB 0/1
IPMI_LAN
FAN6
J24
JPWR2
JPWR1
1
JPP1
JPP0
16
LE1
2 CPUs, 16-24 DIMMs
JPI2C1
JSD1
JWD1
JPME2
2 CPUs, 9-16 DIMMs
FAN5
15
JS1
3. Finish by using a screw to secure the top of the card shield to the chassis.
The PCI slot shields protect the serverboard and its components from EMI
and aid in proper ventilation, so make sure there is always a shield covering
each unused slot.
5-11
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-7 Serverboard Details
X10DRi-T4+ Quick Reference
Figure 5-5. X10DRi-T4+ Layout
LE1
UID
VGA
COM1
IPMI_LAN
LAN1/2
LAN3/4
JUIDB1
FAN5
FAN6
USB 0/1
P2-DIMMG1
P2-DIMMG2
P2-DIMMG3
P2-DIMMH1
P2-DIMMH2
P2-DIMMH3
P2-DIMMF3
P2-DIMMF2
P2-DIMMF1
P2-DIMME3
P2-DIMME2
P2-DIMME1
CPU2 SLOT6 PCI-E 3.0 X8
JPLAN2
JBOD ExpansionPort
CPU2 SLOT4 PCI-E 2.0 X4 IN X8
CPU1 SLOT3 PCI-E 3.0 X16
JTPM1
TPM/PORT80
AOC-S3108L-H81R
JPLAN1
CPU2 SLOT2 PCI-E 3.0 X8
JPG1
CPU2 SLOT1 PCI-E 3.0 X8
COM2
LEDM1
CPU2 SLOT5 PCI-E 3.0 X16
FANC USB 6 (3.0)
JIPMB1
USB4/5
(3.0)
LAN CTRL
LAN CTRL
CPU2
CLOSE 1st
BMC
BIOS
Jumper
Description
Default Setting
JBT1
Clear CMOS
See Section 5-9
JI2C1/JI2C2
SMB to PCI-E Slots
Pins 2-3 (Disabled)
JPB1
BMC Enable/Disable
Pins 1-2 (Enabled)
JPG1
VGA Enable/Disable
Pins 1-2 (Enabled)
JPLAN1
LAN1/2 Enable/Disable
Pins 1-2 (Enabled)
JPLAN2
LAN3/4 Enable/Disable
Pins 1-2 (Enabled)
JPME2
Manufacture (ME) Mode Select
Pins 1-2 (Normal)
JPS1
SAS Enable/Disable
Pins 1-2 (Enabled)
JWD1
Watch Dog Timer
Pins 1-2 (Reset)
Description
COM1/COM2
Backplane COM Port1/Front Accessible COM2 Header
FAN 1-6, A-C
CPU/System Fan Headers
J24
24-pin ATX Main Power Connector
JD1
Speaker/Power LED
JF1
Front Panel Control Header
JIPMB1
4-pin External BMC I2C Header (for an IPMI Card)
JL1
Chassis Intrusion Header
JPI C1
Power Supply SMBbus I2C Header
JPWR1/2
8-Pin Power Connectors
JSD1/JSD2
SATA DOM (Device on Module) Power Connectors
JTPM1
TPM (Trusted Platform Module)/Port 80 Header
JUIDB1
UID (Unit Identification) Button
(IPMI) LAN
Dedicated IPMI LAN support by the ASpeed controller
(I-)SATA 0-5
SATA 3.0 Ports supported by Intel PCH (I-SATA 0-5)
(S-)SATA 0-3
SATA 3.0 Ports supported by Intel SCU (S-SATA 0-3)
SAS 0-3, 4-7
SAS 3.0 Ports supported by the LSI 3108 controller
Slot1
PCI-Express 3.0 x8 Slot from CPU2
Slot2
PCI-Express 3.0 x8 Slot from CPU2
" " indicates the position of pin 1.
Slot3
PCI-Express 3.0 x16 Slot from CPU1
The LSI 3108 onboard controller chip in the layout image above is not populated
on the X10DRi-T4+.
Slot4
PCI-Express 2.0 x4 in x8 Slot from CPU2
Slot5
PCI-Express 3.0 x16 Slot from CPU2
Slot6
PCI-Express 3.0 x8 Slot from CPU2
S-SGPIO1,
T-SGPIO1/2
Serial Link General Purpose I/O Headers (T-SGPIO1 for I-SATA0-3,
T-SGPIO2 for I-SATA4/5, S-SGPIO1 for S-SATA0-3)
BIOS
LICENSE
CPU1
JPWR1
Intel PCH
Rev. 1.01
IPMI CODE
P1-DIMMA1
P1-DIMMA2
P1-DIMMA3
P1-DIMMB1
P1-DIMMB2
P1-DIMMB3
JSD1
JWD1
JPME2
X10DRC/i-LN4+(-T4+)
SAS CODE
JPP1
JPP0
SAN MAC
JPI2C1
MAC CODE
JI2C1
JI2C2
I-SATA2
I-SATA3 I-SATA1
I-SATA4
SP1
CLOSE 1st
JBT1
LEDS5
LEDS6
LSI 3108
SAS CTRL
JSTBY1
JS39
2
OPEN 1st
J24
SAS 0~3 (3.0)
JD1
JPS7
JL1
SAS 4~7 (3.0)
USB 7/8 (3.0)
DS13
JPWR2
I-SATA0
1
Front CTRL Panel
FAN2
LE2
JF1
FAN3
FANA
JS1
FAN4
JPS1
T-SGPIO1
T-SGPIO2
S-SGPIO1
FANB
BAR CODE
P1-DIMMD3
P1-DIMMD2
P1-DIMMD1
P1-DIMMC3
P1-DIMMC2
P1-DIMMC1
I-SATA5
JPB1
JVRM2
JVRM1
S-SATA3 S-SATA2JSD2
USB2/3
S-SATA1 S-SATA0
Connector
JBAT1
OPEN 1st
FAN1
Notes
Jumpers not indicated are for test purposes only and should not have their settings
changed.
Note that the PCI slots are enabled when their corresponding processors are installed. "CPU2 Slot 4" indicates that the second CPU must be installed to the CPU2
socket to enable this PCI slot.
The 6048R-E1CR24N comes pre-installed with a Hardware RAID controller installed
in PCI-E slot 3 and a JBOD expansion port installed in PCI-E slot 4.
5-12
5-13
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-8 Connector Definitions
X10DRi-T4+ Quick Reference (cont.)
SP1
Internal Speaker/Buzzer
JSTBY1
+5V Standby Power Header
USB 0/1
Backpanel USB 2.0 Ports
USB 2/3
Front Accessible USB 2.0 Headers
USB 4/5
Backpanel USB 3.0 Ports
USB 6/7/8
Front Accessible USB 3.0 Headers
LED
Description
State
Status
DS13
SAS Heartbeat LED
Green: Blinking
SAS Normal
LE1
Rear UID LED
Blue: On
Unit Identified
LE2
Onboard Power LED
Green: On
System PWR On
LEDM1
BMC Heartbeat LED
Green: Blinking
BMC Normal
LEDS5
SAS Activity LED
Green: Blinking
SAS Active
LEDS6
SAS Error LED
Red: On
SAS Error(s)
ATX Power 24-pin Connector
Pin Definitions
Pin#
Definition
Power Connectors
13
+3.3V
1
+3.3V
A 24-pin main power supply connector (J24) and two 8-pin CPU power
connectors (JPWR1/JPWR2) must be
connected to the power supplyto provide adequate power to the system.
These power connectors meet the SSI
EPS 12V specification. See the table
on the right for pin definitions.
14
-12V
2
+3.3V
15
COM
3
COM
16
PS_ON
4
+5V
17
COM
5
COM
18
COM
6
+5V
19
COM
7
COM
20
Res (NC)
8
PWR_OK
21
+5V
9
5VSB
22
+5V
10
+12V
23
+5V
11
+12V
24
COM
12
+3.3V
Secondary Power Connector
JPWR1 and JPWR2 must also be
connected to the power supply. See
the table on the right for pin definitions.
Pin #
Definition
+12V 8-pin Power
Pin Definitions
Pins
Definition
1-4
Ground
5-8
+12V
Required Connection
Warning: To provide adequate power supply to the serverboard, be sure to connect
J24 and both JPWR1 and JPWR2 to the power supply. Failure to do so will void
the manufacturer warranty on your power supply and serverboard.
Power Button
The Power On connection is on pins
1 and 2 of JF1. These should be connected to the chassis power button.
Momentarily contacting both pins will
power on/off the system. To turn off
the power when the system is on,
press the button for 4 seconds or
longer. See the table on the right for
pin definitions.
Power Button
Pin Definitions (JF1)
Pin#
Definition
1
Power Signal
2
Ground
Reset Button
The Reset Button connection is
located on pins 3 and 4 of JF1 and
attaches to the reset switch on the
computer chassis. See the table on
the right for pin definitions.
5-14
5-15
Reset Button
Pin Definitions (JF1)
Pin#
Definition
3
Reset
4
Ground
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Power Fail LED
Chapter 5: Advanced Serverboard Setup
PWR Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer to the table on the right for pin
definitions.
Pin#
Definition
5
3.3V
6
PWR Supply Fail
OH/Fan Fail/ PWR Fail/Blue_UID
LED Pin Definitions (JF1)
Overheat, Fan/Power Fail LED
Connect an LED cable to pins 7 and
8 of the front control panel to use the
Overheat/Fan Fail/Power Fail and
UID LED connections. The red LED
on pin 8 provides warnings of overheat, fan failure or power failure. The
blue LED on pin 7 works as the front
panel UID LED indicator. Refer to the
table on the right for pin definitions.
Pin#
Blue_UID LED
8
OH/Fan Fail/Power Fail
OH/Fan Fail/PWR Fail
LED Status (Red LED)
State
Definition
Off
Normal
On
Overheat
Flashing
Fan Fail
NIC2 LED
Pin Definitions (JF1)
Pin#
Definition
9
Activity
10
Link
NIC1 (JLAN1) LED
The LED connections for LAN1 are
on pins 11 and 12 of JF1. Attach an
LED cable to display network activity. See the table on the right for pin
definitions.
The Power On LED connector is located on pins 15 and 16 of JF1 (use
JLED for a 3-pin connector). This
connection is used to provide LED
indication of power being supplied to
the system. See the table on the right
for pin definitions.
Power LED
Pin Definitions (JF1)
Pin#
Definition
15
3.3V
16
PWR LED
Definition
7
NIC2 (JLAN2) LED
The LED connections for LAN2 are
on pins 9 and 10 of JF1. Attach an
LED cable to display network activity. See the table on the right for pin
definitions.
Power On LED
NIC1 LED
Pin Definitions (JF1)
Pin#
Definition
11
Activity
12
Link
NMI Button
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
NMI Button
Pin Definitions (JF1)
Pin#
Definition
19
Control
20
Ground
Fan Headers
There are nine fan headers on the
serverboard, all of which are 4-pin
fans. Pins 1-3 of the fan headers
are backward compatible with the
traditional 3-pin fans. (Fan speed
control is supported with 4-pin fans
only.) See the table on the right for pin
definitions. The onboard fan speeds
are controlled by Thermal Management (via IPMI).
Fan Header
Pin Definitions
(FAN1-8)
Pin#
Definition
1
Ground (Black)
2
+12V (Red)
3
Tachometer
4
PWR Modulation
Chassis Intrusion
HDD LED/UID Switch
The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
cable to pin 14 to show HDD activity
status. Attach a cable to pin 13 to use
UID switch. See the table on the right
for pin definitions.
5-16
HDD LED
Pin Definitions (JF1)
Pin#
Definition
13
UID Switch
14
HD Active
The Chassis Intrusion header is designated JL1. Attach an appropriate
cable from the chassis to inform you
of a chassis intrusion when the chassis is opened
5-17
Chassis Intrusion
Pin Definitions
Pin#
Definition
1
Intrusion Input
2
Ground
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
Ethernet Ports
Four 10Gb Ethernet (LAN) ports are located on the I/O backplane. A dedicated IPMI
LAN port is also included. These ports accept RJ45 type cables.
Internal Speaker
Pin#
COM2 is a header located near PCI-E slot 1.
Back Panel USB 0/1, 2/3 (USB 2.0)
Pin Definitions
Pin 1
Pos. (+)
Beep In
Pin 2
Neg. (-)
Alarm
Speaker
Pin Setting
Power LED/Speaker
On the JD1 header, pins 1-3 are for
a power LED and pins 4-7 are for the
speaker. Close pins 4-7 with a jumper
to use an external speaker. If you wish
to use the onboard speaker, please
close pins 6-7. See the table on the
Pin# Definition
Definitions
PWR LED Connector
Pin Definitions
Definition
Pin 1
JD1_PIN1
Pin 2
FP_PWR_LED
Pin 3
FP_PWR_LED
Universal Serial Bus (USB)
Two USB 3.0 and two USB 2.0 ports
are located on the rear I/O panel. In
addition, two USB 3.0 headers are
provided on the motherboard for three
front accessible USB 3.0 connections
(USB6, USB 7/8). A USB 2.0 header
is also located on the motherboard
to provide two USB 2.0 connections
(USB 2/3) for front access(cables not
included). See the tables on the right
for pin definitions.
Speaker Connector
Pin Settings
Pin Setting
right for speaker pin definitions.
Definition
Pin 4
P5V
Pin 5
Key
Pin 6
R_SPKPIN_N
Pin 7
R_SPKPIN
Pin#
Definition
Pin
Definition
1
NC
2
NC
3
Ground
4
DATA Out
5
Load
6
Ground
7
Clock
8
NC
NC = No Connection
Definition
+5V
5
+5V
2
USB_PN1
6
USB_PN0
3
USB_PP1
7
USB_PP0
4
Ground
8
Ground
USB 4/5, 7/8, (USB 3.0)
Pin Definitions
Pin#
Description
1
VBUS
2
SSRX-
3
SSRX+
4
Ground
5
SSTX-
6
SSTX+
7
GND_DRAIN
8
D-
9
D+
PWR SMBus Header
Pin Definitions
The power System Management Bus
header at JPI2C1 is used to monitor
the status of the power supply, fan and
system temperature. See the table on
the right for pin definitions.
SGPIO Header
Pin Definitions
Pin#
1
Power Supply SMBus I2C Header
SGPIO Headers
5-18
Two serial ports are included on the serverboard. COM1 is a rear I/O port and
Internal Buzzer (SP1)
Pin Definition
The internal speaker, located at SP1,
can be used to provide audible indications for various beep codes. See the
table on the right for pin definitions..
The SGPIO (Serial General Purpose
Input/Output) headers are used to
communicate with the enclosure
management chip on the backplane.
T-SGPIO1/2 support the I-SATA ports
and S-SGPIO1 supports the S-SATA
ports. See the table on the right for
pin definitions.
Serial Ports
Pin#
Definition
1
Clock
2
Data
3
PWR Fail
4
Ground
5
+3.3V
IPMB Header
Pin Definitions
IPMB
A System Management Bus header
for IPMI 2.0 is located at JIPMB1.
Connect the appropriate cable here
to use the IPMB I2C connection on
your system.
5-19
Pin#
Definition
1
Data
2
Ground
3
Clock
4
No Connection
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
DOM Power Connectors
Two power connectors for SATA DOM
(Disk On Module) devices are located
at JSD1/JSD2. Connect appropriate
cables here to provide power support
for your DOM devices.
Chapter 5: Advanced Serverboard Setup
Pin#
Definition
1
+5V
2
Ground
3
Ground
Standby Power Header
The +5V Standby Power header is
located at JSTBY1. See the table
on the right for pin definitions. (You
must also have a card with a Standby
Power connector and a cable to use
this feature.)
TPM/Port 80 Header
Pin Definitions
DOM PWR
Pin Definitions
Pin #
TPM Header/Port 80
A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and a Port 80 connection. Use this header to enhance
system performance and data security. See the table on the right for pin
definitions.
Standby PWR
Pin Definitions
Pin#
Definition
1
+5V Standby
2
Ground
3
No Connection
Unit Identifier Switch
The UID switch and LED are located
next to the rear I/O ports. The rear UID
LED (LE2) is located next to the UID
switch. The front UID switch is located
on pin 13 on JF1 and the front UID
LED is located on pin 7 on JF1. When
you press the front or rear UID switch,
both front and rear UID LEDs will be
turned on. Press the UID switch again
to turn off the LED indicators.These
indicators provide easy identification
of a system unit that may be in need
of service.
UID Switch
Pin#
Definition
1
Ground
2
Ground
3
Button In
4
Button In
UID LED
Status
Color/State Status
Blue: On
Unit Identified
Note: UID can also be triggered via IPMI. For more information on IPMI, please
refer to the IPMI User's Guide posted on our website at http://www.supermicro.com.
5-20
5-21
Definition
Pin #
Definition
1
LCLK
2
GND
3
LFRAME#
4
<(KEY)>
5
LRESET#
6
+5V (X)
7
LAD 3
8
LAD 2
9
+3.3V
10
LAD1
11
LAD0
12
GND
13
SMB_CLK4
14
SMB_DAT4
15
+3V_DUAL
16
SERIRQ
17
GND
18
CLKRUN# (X)
19
LPCPD#
20
LDRQ# (X)
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-9 Jumper Settings
LAN Enable/Disable
Explanation of Jumpers
To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the connector. Pin 1 is identified with a square
solder pad on the printed circuit board.
See the serverboard layout pages for
jumper locations.
Note: On a two-pin jumper, "Closed"
means the jumper is on both pins and
"Open" means the jumper is either on
only one pin or completely removed.
Connector
Pins
3
2
1
Jumper
GLAN Enable
Jumper Settings
JPLAN1 enables or disables the Gb
LAN ports on the serverboard. See
Jumper Setting Definition
the table on the right for jumper settings. The default setting is Enabled.
Pins 1-2
Enabled
Pins 2-3
Disabled
I2C Bus to PCI-Exp. Slots
3
2
1
Setting
Jumpers JI2C1 and JI2C2 allow you
to connect the System Management
Bus (I2C) to the PCI-Express slots to
improve PCI performance. The default
setting is Enabled. Both jumpers must
be set to the same setting See the
table on the right for jumper settings.
I2C to PCI-E Slots
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
CMOS Clear
JBT1 is used to clear CMOS (which will also clear any passwords). Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.
To clear CMOS,
1. First power down the system and unplug the power cord(s).
2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.
3. Remove the screwdriver (or shorting device).
Manufacturer's Mode
Jumper JPME2 allows the user to
flash the system firmware from a
host server in order to modify system
settings. Close this jumper to bypass
SPI flash security, and force ME into
recovery mode in order to use recovery jumpers. See the table on the right
for jumper settings.
ME Mode Select
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Normal
Pins 2-3
Manufacture's Mode
4. Reconnect the power cord(s) and power on the system.
Note: Do not use the PW_ON connector to clear CMOS.
VGA Enable/Disable
JPG1 allows you to enable or disable
the VGA port. The default position is on
pins 1 and 2 to enable VGA. See the
table on the right for jumper settings.
5-22
BMC Enable
VGA Enable/Disable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
Jumper JPB1 allows you to enable
the embedded the ASpeed AST 2400
BMC (Baseboard Management) Controller to provide IPMI 2.0/KVM support on the serverboard. The default
setting is Enabled. See the table on
the right for jumper settings.
5-23
BMC Enable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-10 Onboard Indicators
Watch Dog Enable/Disable
Jumper JWD controls the Watch
LAN LEDs
Dog function. Watch Dog is a system monitor that can reboot the
system when a software application
hangs. Jumping pins 1-2 will cause
WD to reset the system if an application hangs. Jumping pins 2-3 will
generate a non-maskable interrupt
signal for the application that hangs.
See the table on the right for jumper
settings. Watch Dog must also be
enabled in BIOS.
Watch Dog
Jumper Settings
Jumper Setting
Note: When enabled, the user
needs to write their own application software in order to disable the
Watch Dog Timer.
Definition
Pins 1-2
Reset
Pins 2-3
NMI
Open
Disabled
The Ethernet ports (located beside the
VGA port) have two LEDs. On each
port, the orange LED flashes to indicate activity while the other LED may
be green, amber or off to indicate the
speed of the connection. See the table
on the right for the functions associated with the connection speed LED.
LAN1/2 LED
(Connection Speed Indicator)
LED Color
Definition
Off
No link, 10 or 100 Mbps
Green
10 Gbps
Amber
1 Gbps
Dedicated IPMI LAN LEDs
A dedicated IPMI LAN is also located
on the I/O backplane. The amber LED
on the right indicates activity, while
the green LED on the left indicates
the speed of the connection. See the
table at right for more information.
IPMI LAN Link LED (Left) &
Activity LED (Right)
Link (Left)
Activity (Right)
Color/State
Definition
Green: Solid
100 Mbps
Amber: Solid
1 Gbps
Orange:
Blinking
Active
Onboard Power LED (LE1)
An Onboard Power LED is located at
LE2. This LED Indicator is lit when
the system is on. Be sure to unplug
the power cable before removing or
adding any components. See the table
on the right for more details.
BMC Heartbeat LED
A BMC Heartbeat LED is located at
LEDM1 on the serverboard. When
blinking, BMC is functioning normally.
5-24
5-25
Onboard PWR LED Indicator
LED States
Color/State
Definition
Off
System Power Off
Green: On
System Power On
BMC Heartbeat LED
States
Color/State
Definition
Green: Blinking
BMC Normal
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
5-11 SAS/SATA Ports
Chapter 5: Advanced Serverboard Setup
5-12 Installing Software
The Supermicro FTP site contains drivers and utilities for your system at ftp://ftp.
supermicro.com. Some of these must be installed, such as the chipset driver.
SAS Ports
An LSI 3108 controller card is included in the system to support up to 240 SATA
3.0/SAS 3.0 hard drives.
SATA Ports
There are ten SATA 3.0 ports included on the serverboard. Six ports (I-SATA
0-5) are supported by the Intel PCH C612 while the other four (S-SATA 0-3) are
supported by the Intel SCU. These ports provide serial-link signal connections,
which are faster than Parallel ATA.
After accessing the FTP site, go into the CDR_Images directory and locate the ISO
file for your serverboard. Download this file to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO file if preferred.)
Another option is to go to the Supermicro website at http://www.supermicro.com/
products/. Find the product page for your serverboard here, where you may download individual drivers and utilities.
After creating a CD/DVD with the ISO files, insert the disk into the CD/DVD drive
on your system and the display shown in Figure 5-6 should appear.
Note: For more information on SATA HostRAID configuration, please refer to the
Intel SATA HostRAID User's Guide posted on our website at http://www.supermicro.
com..
Figure 5-6. Driver/Tool Installation Display Screen
Note: Click the icons showing a hand writing on paper to view the readme files
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents.
5-26
5-27
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 5: Advanced Serverboard Setup
5-13 Onboard Battery
SuperDoctor® 5
The Supermicro SuperDoctor 5 is a program that functions in a command-line or
web-based interface in Windows and Linux operating systems. The program monitors system health information such as CPU temperature, system voltages, system
power consumption, fan speed, and provides alerts via email or Simple Network
Management Protocol (SNMP).
SuperDoctor 5 comes in local and remote management versions and can be used
with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Management Server (SSM Server), you can remotely control power on/off and reset
chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Management Server monitors HTTP, FTP, and SMTP services to optimize the efficiency of
your operation.
Care must be taken to assure that the chassis cover is in place when the system
is operating to assure proper cooling. Out of warranty damage to the system can
occur if this practice is not strictly followed.
Figure 5-8. Installing the Onboard Battery
Note: The default User Name and Password for SuperDoctor 5 is admin / admin.
OR
Figure 5-7. SuperDoctor 5 Interface Display Screen (Health Information)
Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.
Note: The SuperDoctor 5 program and User’s Manual can be downloaded from
the Supermicro web site at http://www.supermicro.com/products/nfo/sms_sd5.cfm.
5-28
5-29
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
5-30
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform maintenance on the SC846BE1C-R920B chassis. For component installation, follow the
steps in the order given to eliminate the most common problems encountered. If
some steps are unnecessary, skip ahead to the step that follows.
Tools Required: The only tool you will need to install components and perform
maintenance is a Philips screwdriver.
6-1 Static-Sensitive Devices
Electrostatic discharge (ESD) can damage electronic com­
ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally sufficient to protect your equipment
from ESD damage.
Precautions
•Use a grounded wrist strap designed to prevent static discharge.
•Touch a grounded metal object before removing any board from its antistatic bag.
•Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
•For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
Unpacking
The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
6-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Figure 6-1. Front and Rear Chassis Views
Chapter 6: Advanced Chassis Setup
6-3 Removing the Chassis Cover
13
1
1
Control Panel
Power Supplies (2)
12
Hard Drives (24)
JBOD Expansion Ports
Hardware RAID Add-on Card
Remove this screw
(if necessary)
Release Tab
Figure 6-2. Removing the Chassis Cover
Optional Rear Hot-Swap Drive Bays
I/O Ports
PCI Expansion Slots
Removing the Chassis Cover
You may need to gain access to the inside of the server to perform various maintenance tasks.
6-2 Control Panel
The control panel (located on the front of the chassis) must be connected to the
JF1 connector on the serverboard to provide you with system status indications. A
ribbon cable has bundled these wires together to simplify the connection. Connect
the cable from JF1 on the serverboard to the Control Panel PCB (printed circuit
board). Make sure the red wire plugs into pin 1 on both connectors. Pull all excess
cabling out of the airflow path. The LEDs inform you of system status. See Chapter 3 for details on the LEDs and the control panel buttons. Details on JF1 can be
found in Chapter 5.
1. Press the release tabs to remove the cover from the locked position. Press
both tabs at the same time.
2. Once the top cover is released from the locked position, slide the cover
toward the rear of the chassis.
3. Lift the cover off the chassis.
Warning: Except for short periods of time, do NOT operate the server without the
cover in place. The chassis cover must be in place to allow proper airflow and prevent
overheating.
6-2
6-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
6-4 System Fans
Chapter 6: Advanced Chassis Setup
Figure 6-3. Replacing System Cooling Fans
Three 8-cm hot-swap chassis fans and two 8-cm exhaust fans provide the cooling
for the SuperServer 6048R-E1CR24N. It is very important that the chassis top cover
is properly installed and making a good seal in order for the cooling air to circulate
properly through the chassis and cool the components. See Figure 6-3.
System Fan Failure
Fan speed is controlled by system temperature via IPMI. If a fan fails, the remaining
fans will ramp up to full speed and the overheat/fan fail LED on the control panel will
turn on. Replace any failed fan at your earliest convenience with the same type and
model (the system can continue to run with a failed fan). Remove the top chassis
cover while the system is still running to determine which of the fans has failed.
Replacing System Fans
Removing a Fan
1. Remove the top chassis cover while the system is still running to determine
which of the fans has failed.
2. Depress the tab on the side of the fan to unlock and remove the fan along
with its housing. The fan's power connections will automatically detach.
3. System power does not need to be shut down since the fans are hot-pluggable.
4. Replace the failed fan with an identical 8-cm, 12 volt fan (available from
Supermicro).
5. Position the new fan into the space vacated by the failed fan previously removed. A "click" can be heard when the fan is fully installed in place and the
power connections are made.
6. If the system power is on, the hot-plug feature will cause the fan to start immediately upon being connected to its header on the serverboard.
6-5 Drive Bay Installation/Removal
Accessing the Drive Bays
SATA Drives: You do not need to access the inside of the chassis or remove power
to replace or swap SATA drives. Proceed to the next step for instructions.
Note: You must use standard 1" high, drives in the SuperServer 6048R-E1CR24N.
Warning: Use caution when working around the backplane. Do not touch the backplane with any metal objects and make sure no ribbon cables touch the backplane or
obstruct the holes, which aid in proper airflow.
Rear Exhaust Fans
The two rear exhaust fans are also hot-swappable. To remove, depress the tab on
the side of the fan to unlock it, then pull it staight up and out of the chassis.
6-4
6-5
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 6: Advanced Chassis Setup
SATA Drive Installation
Figure 6-4. Mounting a SATA Drive in a Carrier
Mounting a SATA Drive in a Drive Carrier
The SATA drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airflow for the
drives. For this reason, even empty carriers without SATA drives installed must remain in the chassis. To add a new SATA drive, install a drive into the carrier with the
printed circuit board side facing down so that the mounting holes align with those in
the carrier. Secure the drive to the carrier with four screws, as shown in Figure 6-3.
1
1
Installing/Removing SATA Drives
1. To remove a SATA drive carrier, first push the release button located beside
the drive's LEDs.
2. Swing the handle fully out and use it to pull the drive carrier straight out.
Warning: Regardless of how many hard drives are installed, all drive carriers must
remain in the drive bays to maintain proper airflow.
Installing a Hard Drive to the Hard Drive Tray
1. Remove the two screws securing the dummy drive to the drive tray and
remove the dummy drive.Place the hard drive tray on a flat surface such as a
desk, table or work bench (see Figure 6-4).
Figure 6-5. Installing a Drive Carrier
2. Slide the hard drive into the tray with the printed circuit board side facing
down.
3. Carefully align the mounting holes in both the drive tray and the hard drive.
4. Secure the hard drive to the tray using six screws.
5. Replace the drive tray into the chassis. Make sure to close the drive tray
handle to lock the drive tray into place (see Figure 6-5)..
15
Warning: Enterprise level hard disk drives are recommended for use in Supermicro
chassis and servers. For information on recommended HDDs, visit the Supermicro Web
site at http://www.supermicro.com/products/nfo/files/storage/SAS-1-CompList-110909.
Hard Drive Backplane
pdf
The hard drives plug into a backplane that provides power, drive ID and bus termination. A RAID controller can be used with the backplane to provide data security.
The operating system you use must have RAID support to enable the hot-swap
capability of the SATA drives. The backplane is already preconfigured, so there are
no jumpers or switches present on it.
6-6
6-7
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Removing the Air Shroud
Under most circumstances you will not need to remove the air shroud to perform
any service on the system. However, if you need to temporarily remove it (the air
shroud sould always be in place when the system is operating), please follow this
procedure.
Air shrouds concentrate airflow to maximize fan efficiency. The SC846 chassis air
shroud does not require screws to set up
Installing the Air Shroud
1. Confirm that your air shroud matches your chassis model. Each shroud is
labeled SC846LP, SC846RC, or SC846U.
2. Place the air shroud in the chassis. The air shroud fits behind the two fans
closest to the power supply.
Chapter 6: Advanced Chassis Setup
6-6 Power Supply
The SuperServer 6048R-E1CR24N has a 920 watt redundant, hot-plug power
supply consisting of two power modules. Each power supply module has an autoswitching capability, which enables it to automatically sense and operate at a 100V
- 240V input voltage.
Power Supply Failure
If either of the two power supply modules fail, the other will take the full load and
allow the system to continue operation without interruption. The Power Fail LED will
illuminate and remain on until the failed module has been replaced. Replacements
can be ordered directly from Supermicro (see contact information in the Preface).
The power supply modules have a hot-swap capability, meaning you can replace
the failed module without powering down the system.
Removing/Replacing the Power Supply
1. First unplug the power cord from the failed power supply module.
Figure 6-6. Removing the Air Shroud
2. Push the release tab on the back of the power supply as illustrated
3. Pull the power supply out using the handle provided.
4. Replace the failed power module with another of the same model.
5. Push the new power supply module into the power bay until it clicks into the
locked position.
6. Plug the AC power cord back into the module.
6-8
6-9
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 6: Advanced Chassis Setup
Figure 6-8. JBOD Expansion Port
2x JBOD OUT
(downstream ports)
Figure 6-7. Replacing a Power Supply Module
JBOD IN
(upstream port)
Release
Tab
JBOD OUT
JBOD IN
(downstream port)
(upstream port)
6-7 Attaching a JBOD Expansion Chassis
The SSG-6048R-E1CR24N features dual JBOD expansion ports. Figure 6-8 illustrates the recommended expansion strategy. JBOD attachment will vary depending
on the specific JBOD chassis that is being connected. Please follow the instructions
provided with the JBOD.
JBOD OUT
(downstream port)
6-10
6-11
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
6-12
Chapter 7: BIOS
Chapter 7
BIOS
7-1 Introduction
This chapter describes the AMI BIOS setup utility for the X10DRC/i-LN4+/-T4+. The
ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter
describes the basic navigation of the AMI BIOS setup utility screens.
Starting BIOS Setup Utility
To enter the AMI BIOS setup utility screens, press the <Delete> key while the
system is booting up.
Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen.
Each main BIOS menu option is described in this manual. The AMI BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it.
Note: the AMI BIOS has default text messages built in. Supermicro retains
the option to include, omit, or change any of these text messages.
The AMI BIOS setup utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F4>, <Enter>, <Esc>, arrow
keys, etc.
Note: Options printed in Bold are default settings.
How To Change the Configuration Data
The configuration data that determines the system parameters may be changed by
entering the AMI BIOS setup utility. This setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.
7-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
How to Start the Setup Utility
Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS setup utility. From the main menu, you can access the other setup
screens. An AMI BIOS identification string is displayed at the left bottom corner of
the screen, below the copyright message.
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you have to update the BIOS, do not shut down or reset
the system while the BIOS is updating to avoid possible boot failure.
Chapter 7: BIOS
The following Main menu items will be displayed:
System Date/System Time
Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values using the keyboard. Press the
<Tab> key or the arrow keys to move between fields. The date must be entered in
Day MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears
as 17:30:00.
Supermicro X10DRC-T4+ Series
BIOS Version: This item displays the version of the BIOS ROM used in the
system.
7-2 Main Setup
When you first enter the AMI BIOS setup utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS setup screen is shown below.
Build Date: This item displays the date when the version of the BIOS ROM used
in the system was built.
Memory Information
Total Memory: This item displays the total size of memory available in the system.
Memory Speed: This item displays the default speed of the memory modules
installed in the system.
7-2
7-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
7-3 Advanced Setup Configurations
Use the arrow keys to select Advanced setup and press <Enter> to access the
submenu items:
Chapter 7: BIOS
Wait For 'F1' If Error
Select Enabled to force the system to wait until the <F1> key is pressed if an error
occurs. The options are Disabled and Enabled.
INT19 (Interrupt 19) Trap Response
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Immediate, the ROM BIOS of the host adaptors will "capture" Interrupt
19 at bootup immediately and allow the drives that are attached to the host adaptors to function as bootable disks. If this item is set to Postponed, the ROM BIOS
of the host adaptors will not capture Interrupt 19 immediately to allow the drives
attached to the adaptors to function as bootable devices at bootup. The options
are Immediate and Postponed.
Re-try Boot
Select EFI Boot to allow the BIOS to automatically reboot the system from an EFI
boot device after its initial boot failure. Select Legacy Boot to allow the BIOS to
automatically reboot the system from a Legacy boot device after its initial boot
failure. The options are Disabled, Legacy Boot, and EFI Boot.
Warning: Take Caution when changing the Advanced settings. An incorrect value, a
very high DRAM frequency or an incorrect BIOS timing setting may cause the system
to malfunction. When this occurs, restore the setting to the manufacture default setting.
Boot
Power Configuration
Watch Dog Function
Select Enabled to allow the Watch Dog timer to reboot the system when it is inactive for more than 5 minutes. The options are Enabled and Disabled.
Feature
Quiet Boot
Power Button Function
Use this feature to select the screen display between POST messages or the OEM
logo at bootup. Select Disabled to display the POST messages. Select Enabled
to display the OEM logo instead of the normal POST messages. The options are
Enabled and Disabled.
This feature controls how the system shuts down when the power button is pressed.
Select 4 Seconds Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are 4 Seconds Override and Instant Off.
AddOn ROM Display Mode
Use this item to set the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.
Bootup Num-Lock State
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off and Last State.
Use this feature to set the Power-on state for the Numlock key. The options are
Off and On.
7-4
7-5
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
CPU Configuration
This submenu displays the following CPU information as detected by the BIOS. It
also allows the user to configure CPU settings.
Chapter 7: BIOS
illegal codes to overwhelm the processor to damage the system during an attack.
The options are Enable and Disable. (Refer to Intel's and Microsoft's websites for
more information.)
•Processor Socket
PPIN Control
•Processor ID
Select Unlock/Enable to use the Protected-Processor Inventory Number (PPIN)
control in the system. The options are Unlock/Enable and Unlock/Disable.
•Processor Frequency
Hardware Prefetcher (Available when supported by the CPU)
•Processor Max Ratio
If set to Enable, the hardware prefetcher will prefetch streams of data and instructions from the main memory to the L2 cache to improve CPU performance. The
options are Disable and Enable.
•Processor Min Ratio
Adjacent Cache Line Prefetch (Available when supported by the CPU)
•Microcode Revision
Select Enable for the CPU to prefetch both cache lines for 128 bytes as comprised.
Select Disable for the CPU to prefetch both cache lines for 64 bytes. The options
are Disable and Enable.
•L1 Cache RAM
•L2 Cache RAM
Note: Please reboot the system for changes on this setting to take effect.
Please refer to Intel’s website for detailed information.
•L3 Cache RAM
•CPU 1 Version
DCU (Data Cache Unit) Streamer Prefetcher (Available when supported by
the CPU)
•CPU 2 Version
If set to Enable, the DCU Streamer prefetcher will prefetch data streams from the
cache memory to the DCU (Data Cache Unit) to speed up data accessing and
processing to enhance CPU performance. The options are Disable and Enable.
Clock Spread Spectrum
Select Enabled to allow the BIOS to monitor and attempt to reduce the level of
Electromagnetic Interference caused by the components whenever needed. The
options are Disabled and Enabled.
Hyper-Threading (All)
Select Enable to support Intel's Hyper-threading Technology to enhance CPU performance. The options are Enable and Disable.
Cores Enabled
This feature allows the user to determine the number of CPU cores to enable. Enter
"0" to enable all cores. There are 14 cores available in the system. The default setting is 0, which enables all CPU cores in the system.
Execute Disable Bit (Available if supported by the OS & the CPU)
Select Enable for Execute Disable Bit Technology support, which will allow the
processor to designate areas in the system memory where an application code
can execute and where it cannot, thus preventing a worm or a virus from flooding
7-6
DCU IP Prefetcher
If set to Enable, the IP prefetcher in the DCU (Data Cache Unit) will prefetch IP
addresses to improve network connectivity and system performance. The options
are Enable and Disable.
DCU Mode
Use this feature to set the data-prefecting mode for the DCU (Data Cache Unit).
The options are 32KB 8Way Without ECC and 16KB 4Way With ECC.
Direct Cache Access (DCA)
Select Enable to use Intel DCA (Direct Cache Access) Technology to improve the
efficiency of data transferring and accessing. The options are Auto, Enable, and
Disable.
DCA Prefetch Delay
A DCA prefetcher is used with a TOE (TCP/IP Offload Engine) adapter to prefetch
data in order to shorten execution cycles and maximize data processing efficiency.
7-7
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
Prefetching data too frequently can saturate the cache directory and delay necessary cache access. This feature reduces or increases the frequency the system
prefetches data. The options are Disable, [8], [16], [24], [32], [40], [48], [56], [64],
[72], [80], [88], [96], [104], [112].
CPU P State Control (Available when Power Technology
is set to Custom)
X2 APIC (Advanced Programmable Interrupt Controller)
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust the processor voltage and core frequency to reduce power consumption
and heat dissipation. The options are Disable and Enable.
Based on Intel's Hyper-Threading architecture, each logical processor (thread) is
assigned 256 APIC IDs (APIDs) in 8-bit bandwidth. When this feature is set to Enable, the APIC ID will expand(X2) from 8 bits to 16 bits to provide 512 APIDs to each
thread for CPU performance enhancement. The options are Disable and Enable.
AES-NI
Select Enable to use the Intel Advanced Encryption Standard (AES) New Instructions (NI) to ensure data security. The options are Enable and Disable.
Intel Virtualization Technology
Select Enable to use Intel Virtualization Technology support for Direct I/O VT-d support by reporting the I/O device assignments to the VMM (Virtual Machine Monitor)
through the DMAR ACPI tables. This feature offers fully-protected I/O resource
sharing across Intel platforms, providing greater reliability, security and availability
in networking and data-sharing. The options are Enable and Disable.
 Advanced Power Management Configuration
Advanced Power Management Configuration
Power Technology
Select Energy Efficient to support power-saving mode. Select Custom to customize system power settings. Select Disabled to disable power-saving settings. The
options are Disable, Energy Efficient, and Custom.
If the option is set to Energy Efficient or Custom, the following items will display:
EIST (P-States)
Turbo Mode
Select Enabled to use the Turbo Mode to boost system performance. The options
are Enable and Disable.
P-State Coordination
This feature is used to change the P-state (Power-Performance State) coordination type. P-state is also known as "SpeedStep" for Intel processors. Select
HW_ALL to change the P-state coordination type for hardware components only.
Select SW_ALL to change the P-state coordination type for all software installed
in the system. Select SW_ANY to change the P-state coordination type for a software program in the system. The options are HW_All, SW_ALL, and SW_ANY.
CPU C State Control (Available when Power Technology
is set to Custom)
Package C State limit
Use this item to set the limit on the C-State package register. The options are
C0/1 state, C2 state, C6 (non-Retention) state, and C6 (Retention) state.
CPU C3 Report
Select Enable to allow the BIOS to report the CPU C3 State (ACPI C2) to the
operating system. During the CPU C3 State, the CPU clock generator is turned
off. The options are Enable and Disable.
Config TDP (Configuring Thermal Design Power)
CPU C6 Report (Available when Power Technology is set to Custom)
Select Enable to configure TDP power settings to enhance thermal management.
The options are Enable and Disable.
Select Enable to allow the BIOS to report the CPU C6 state (ACPI C3) to the
operating system. During the CPU C6 state, power to all cache is turned off.
The options are Enable and Disable.
Config TDP Level (Available when Config TDP above is set to Enable)
Use this item to set TDP configuration level to enhance thermal management.
The options are Nominal, Level 1, and Level 2.
7-8
Enhanced Halt State (C1E)
Select Enabled to use Enhanced Halt-State technology, which will significantly
reduce CPU power consumption by reducing CPU clock cycles and voltages
during a Halt-state. The options are Disable and Enable.
7-9
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
CPU T State Control (Available when Power Technology
is set to Custom)
ACPI (Advanced Configuration Power Interface) T-States
Select Enable to support CPU throttling by the operating system to reduce power
consumption. The options are Enable and Disable.
Socket RAPL (Running Average Power Limit) Config.
(Configuration)
Chapter 7: BIOS
Short Duration Power Limit
This item displays the time period during which short duration power is maintained. The default setting is 0.
Package Clamping Limit2
Use this item to set the limit on power performance states for the processor
operating in turbo mode, with P0 being the state with the highest frequency
(clock speed) and power (consumption), and P1, a step lower in performance
than P0, with its frequency and voltage scaled back a notch. The options are
Between P1/P0 and Below P1.
FAST_RAPL_NSTRIKE_PL2_DUTY_CYCLE
This feature displays the value of the item above within the range between 25
(10%) and 64 (25%). The default setting is 64.
Turbo Power Limit Lock
Select Enable to set the power use limit for the machine when it is running in
the turbo mode. The options are Enable and Disable.
Chipset Configuration
Warning! Please set the correct settings for the items below. A wrong configuration
setting may cause the system to become malfunction.
North Bridge
This feature allows the user to configure the settings for the Intel North Bridge.
Long Power Limit Override
Select Enable to support long-term power limit override. If this feature is disabled,
BIOS will set the default value. The options are Enable and Disable.
IIO Configuration
Long Duration Power Limit
EV DFX (Device Function On-Hide) Features
This item displays the power limit set by the user during which long duration
power is maintained. The default setting is 0.
When this feature is set to Enable, the EV_DFX Lock Bits that are located on a
processor will always remain clear during electric tuning. The options are Disable and Enable.
Long Duration Time Window
Use this item to set the time window value (in seconds) over which the TDP
(Thermal Design Point) should be maintained. The default setting is 0, which will
allow the value to be automatically programed by the system.
Package Clamping Limit1
Use this item to set the limit on power performance states for the runtime processor, with P0 being the state with the highest frequency (clock speed) and power
(consumption), and P1, a step lower in performance than P0, with its frequency
and voltage scaled back a notch. The options are Between P1/P0 and Below P1.
Short Duration Power Limit Enable
Select Enable to support Short Duration Power Limit (Power Limit 2). The options
are Enable and Disable.
7-10
IIO1 Configuration
IOU2 (II0 PCIe Port 1)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4, x8, and Auto.
II01 PORT 1A Link Speed
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
IOU0 (II0 PCIe Port 2)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
7-11
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
II01 PORT 2A Link Speed
II02 PORT 3A Link Speed
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
IOU1 (II01 PCIe Port 3)
II02 PORT 3C Link Speed
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
II01 PORT 3A Link Speed
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
IOAT (Intel® IO Acceleration) Configuration
II01 PORT 3C Link Speed
Select Enable to enable Intel I/OAT (I/O Acceleration Technology) support, which
significantly reduces CPU overhead by leveraging CPU architectural improvements and freeing the system resource for other tasks. The options are Enable
and Disable.
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
Enable IOAT
No Snoop
IIO2 Configuration
Select Enable to support no-snoop mode for each CB device. The options are
Disable and Enable.
IOU2 (II02 PCIe Port 1)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4, x8, and Auto.
II02 PORT 1A Link Speed
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
IOU0 (II02 PCIe Port 2)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
Relaxed Ordering
Select Enable to enable Relaxed Ordering support which will allow certain
transactions to violate the strict-ordering rules of PCI bus for a transaction to
be completed prior to other transactions that have already been enqueued. The
options are Disable and Enable.
 Intel VT for Directed I/O (VT-d)
Intel VT for Direct I/O (VT-d)
Intel® VT for Directed I/O (VT-d)
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s),
and Gen 3 (Generation 3) (8 GT/s).
Select Enable to use Intel Virtualization Technology support for Direct I/O VT-d
support by reporting the I/O device assignments to the VMM (Virtual Machine
Monitor) through the DMAR ACPI tables. This feature offers fully-protected I/O
resource sharing across Intel platforms, providing greater reliability, security and
availability in networking and data-sharing. The options are Enable and Disable.
IOU1 (II02 PCIe Port 3)
Interrupt Remapping
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
Select Enable for Interrupt Remapping support to enhance system performance.
The options are Enable and Disable.
II02 PORT 2A Link Speed
7-12
7-13
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
Coherency Support (Non-Isoch)
Link L1 Enable
Select Enable for the Non-Iscoh VT-d engine to pass through DMA (Direct
Memory Access) to enhance system performance. The options are Enable and
Select Enable for Link L1 support. The options are Enable and Disable.
Disable.
COD Enable (Available when the OS and the CPU support this feature)
Coherency Support (Isoch)
Select Enable for Cluster-On-Die support to enhance system performance in
cloud computing. The options are Enable, Disable, and Auto.
Select Enable for the Iscoh VT-d engine to pass through ATS to enhance system
performance. The options are Enable and Disable.
Early Snoop (Available when the OS and the CPU support this feature)
QPI (Quick Path Interconnect) Configuration
Select Enable for Early Snoop support to enhance system performance. The
options are Enable, Disable, and Auto.
Isoc Mode
QPI General Configuration
QPI Status
Select Enable for Isochronous support to meet QoS (Quality of Service) requirements. This feature is especially important for Virtualization Technology. The
options are Enable and Disable.
The following information will display:
•Number of CPU
Memory Configuration
•Number of II0
Enforce POR
•Current QPI Link Speed
Select Enabled to enforce POR restrictions on DDR4 frequency and voltage
programming. The options are Enabled and Disabled.
•Current QPI Link Frequency
Memory Frequency
•QPI Global MMIO Low Base/Limit
•QPI Global MMIO High Base/Limit
•QPI PCIe Configuration Base/Size
Link Speed Mode
Use this item to select the data transfer speed for QPI Link connections. The
options are Fast and Slow.
Link Frequency Select
Use this item to select the desired frequency for QPI Link connections. The options are 6.4GB/s, 8.0GB/s, 9.6GB/s, Auto, and Auto Limited.
Link L0p Enable
Select Enable for Link L0p support. The options are Enable and Disable.
Use this feature to set the maximum memory frequency for onboard memory
modules. The options are Auto, 1333, 1400, 1600, 1800, 1867, 2000, 2133,
2200, 2400, 2600, 2667, and Reserved (Do not select Reserved).
ECC Support
Select Enable to enable Error Checking & Correction (ECC) support for onboard
memory modules. The options are Auto, Enable and Disable.
Data Scrambling
Select Enabled to enable data scrambling to enhance system performance and
data integrity. The options are Auto, Disabled and Enabled.
Enable ADR
Select Enabled for ADR (Automatic Diagnostic Repository) support to enhance
memory performance. The options are Enabled and Disabled.
DRAM RAPL (Running Average Power Limit) Baseline
Use this feature to set the run-time power-limit baseline for DRAM modules. The
options are Disable, DRAM RAPL Mode 0, and DRAM RAPL Mode 1.
7-14
7-15
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
Set Throttling Mode
Memory Rank Sparing
Throttling improves CPU reliability and reduces power consumption via automatic-voltage control during CPU idle states. The options are Disabled and CLTT
(Closed Loop Thermal Throttling).
Select Enable to enable memory-sparing support for memory ranks to improve
memory performance. The options are Disabled and Enabled.
Socket Interleave Below 4GB
Patrol Scrubbing is a process that allows the CPU to correct correctable memory
errors detected on a memory module and send the correction to the requestor
(the original source). When this item is set to Enable, the IO hub will read and
write back one cache line every 16K cycles, if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the IO hub
will be scrubbed every day. The options are Enable and Disable.
Select Enable for the memory above the 4G Address space to be split between
two sockets. The options are Enable and Disable.
Channel Interleaving
Use this item to set DIMM channel interleaving mood. The options are Auto,
1-Way Interleave, 2-Way Interleave, 3-Way Interleave, and 4-Way Interleave.
Rank Interleaving
Patrol Scrub
Patrol Scrub Interval
Use this item to select a rank memory interleaving method. The options are Auto,
1-Way, 2-Way, 4-Way, and 8-Way.
This feature allows you to decide how many hours the system should wait before
the next complete patrol scrub is performed. Use the keyboard to enter a value
from 0-24. The Default setting is 24.
A7 Mode
Demand Scrub
Select Enable to support the A7 (Addressing) mode to improve memory performance. The options are Enable and Disable.
Demand Scrubbing is a process that allows the CPU to correct correctable
memory errors found on a memory module. When the CPU or I/O issues a
demand-read command, and the read data from memory turns out to be a
correctable error, the error is corrected and sent to the requestor (the original
source). Memory is updated as well. Select Enable to use Demand Scrubbing
for ECC memory correction. The options are Enable and Disable.
DIMM Information
This item displays the status of a DIMM module as detected by the AMI
BIOS.
Device Tagging
Memory RAS (Reliability_Availability_Serviceability) Configuration
Select Enable to support device tagging. The options are Disable and Enable.
Use this submenu to configure the following Memory RAS settings.
RAS Mode
When Disable is selected, RAS is not supported. When Mirror is selected, the
motherboard maintains two identical copies of all data in memory for data backup.
When Lockstep is selected, the motherboard uses two areas of memory to run
the same set of operations in parallel to boost performance. The options are
Disable, Mirror, and Lockstep Mode.
Lockstep x4 DIMMs
Select Enable to enable Lockstep support for x4 DIMM modules. The options
are Auto, Disabled, and Enabled.
7-16
7-17
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
South
Bridge Configuration
The following South Bridge information will display:
USB
Configuration
•USB Module Version
Chapter 7: BIOS
EHCI2
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #2 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
XHCI Pre-Boot Drive
Select Enabled to enable XHCI (Extensible Host Controller Interface) support on a
pre-boot drive specified by the user. The options are Enabled and Disabled.
•USB Devices
XHCI Idle L1
Legacy USB Support
Select Enabled to support onboard legacy USB devices. Select Auto to disable
legacy support if there are no legacy USB devices present. Select Disabled to
have all USB devices available for EFI applications only. The options are Enabled,
Disabled and Auto.
XHCI Hand-Off
This is a work-around solution for operating systems that do not support XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership change should be
claimed by the XHCI driver. The settings are Enabled and Disabled.
Select Enabled for XHCI (Extensible Host Controller Interface) Idle Level 1 support on a USB 3.0 connector specified by the user. The options are Enabled and
Disabled.
PCH DMI ASPM
Select Enabled to enable ASPM (Active State Power Management) support for a
PCH DMI drive. The options are Disabled and Enabled.
EHCI Hand-Off
This item is for operating systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change will
be claimed by the EHCI driver. The settings are Enabled and Disabled.
USB Mass Storage Driver Support
Select Enabled to support USB mass storage devices. The options are Disabled
and Enabled.
Port 60/64 Emulation
Select Enabled to support I/O port 60h/64h emulation, which will provide complete
legacy USB keyboard support for the operating systems that do not support legacy
USB devices. The options are Disabled and Enabled.
USB 3.0 Support
Select Enabled for USB 3.0 support. The options are Smart Auto, Auto, Enabled,
Disabled, and Manual.
EHCI1
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #1 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
7-18
7-19
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
SATA
Configuration
Chapter 7: BIOS
Port 0 ~ Port 5 SATA Device Type
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the Intel PCH chip and displays the following items:
SATA Controller
Select Enabled to enable the onboard SATA controller supported by the Intel PCH
chip. The options are Enabled and Disabled.
Configure SATA as
Select IDE to configure a SATA drive specified by the user as an IDE drive. Select
AHCI to configure a SATA drive specified by the user as an AHCI drive. Select
RAID to configure a SATA drive specified by the user as a RAID drive. The options
are IDE, AHCI, and RAID.
*If the item above "Configure SATA as" is set to AHCI, the following items will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
SATA Port 0~ Port 5
This item displays the information detected on the installed SATA drive on the
particular SATA port.
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure SATA as" is set to IDE, the following items will
display:
Serial ATA Port 0~ Port 5
This item indicates that a SATA port specified by the user is installed (present)
or not.
Port 0 ~ Port 5 SATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure SATA as" is set to RAID, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
•Model number of drive and capacity
Serial ATA Port 0~ Port 5
•Software Preserve
This item displays the information detected on the installed SATA drives on the
particular SATA port.
•Model number of drive and capacity
Port 0~ Port 5
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
•Software Preserve
Port 0~ Port 5
Port 0 ~ Port 5 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a SATA disk drive installed on this port without
shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 5 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to initialize the
device. The options are Enabled and Disabled.
7-20
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
Port 0 ~ Port 5 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a SATA disk drive installed on this port without
shutting down the system. The options are Enabled and Disabled.
7-21
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
Port 0 ~ Port 5 Spin Up Device
sSATA Port 0~ Port 3
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
Port 0 ~ Port 5 SATA Device Type
sSATA Port 0 ~ Port 3 Hot Plug
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a sSATA disk drive installed on this port
without shutting down the system. The options are Enabled and Disabled.
sSATA
sSATA Port 0 ~ Port 3 Spin Up Device
Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the PCH-sSATA controller and displays
the following items:
sSATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH-sSATA controller. The options are Enabled and Disabled.
Configure sSATA as
Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select
RAID to configure an sSATA drive specified by the user as a RAID drive. The options are IDE, AHCI, and RAID.
*If the item above "Configure sSATA as" is set to AHCI, the following items will
display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to IDE, the following items will
display:
sSATA Port 0~ Port 3
This item indicates that an sSATA port specified by the user is installed (present) or not.
Port 0 ~ Port 3 sSATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to RAID, the following items will
display:
sSATA Port 0~ Port 3
Support Aggressive Link Power Management
This item displays the information detected on the installed on the sSATA port.
specified by the user.
•Model number of drive and capacity
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
•Software Preserve
sSATA Port 0~ Port 3
This item displays the information detected on the installed sSATA drives on the
particular sSATA port.
•Model number of drive and capacity
7-22
7-23
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
•Software Preserve
Chapter 7: BIOS
PCIe/PCI/PnP Configuration
The following PCI information will be displayed:
sSATA Port 0~ Port 3
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
•PCI Bus Driver Version
•PCI Device Common Settings
sSATA Port 0 ~ Port 3 Hot Plug
This feature designates this port for hot plugging. Set this item to Enabled for
hot-plugging support, which will allow the user to replace an sSATA drive without
shutting down the system. The options are Enabled and Disabled.
sSATA Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
Server ME (Management Engine) Configuration
This feature displays the following system ME configuration settings.
•General ME Configuration
PCI Latency Timer
Use this item to configure the PCI latency timer for a device installed on a PCI bus.
Select 32 to set the PCI latency timer to 32 PCI clock cycles. The options are 32,
64, 96, 128, 160, 192, 224, and 248 (PCI Bus Clocks).
PCI-X Latency Timer
Use this item to configure the PCI-X latency timer for a device installed on a PCI
bus. Select 32 to set the PCI latency timer to 32 PCI clock cycles. The options are
32, 64, 96, 128, 160, 192, 224, and 248 (PCI Bus Clocks).
VGA Palette Snoop
Select Enabled to support VGA palette register snooping which will allow a PCI
card that does not contain its own VGA color palette to examine a video card palette and mimic it for proper color display. The options are Disabled and Enabled.
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are Enabled and Disabled.
•Operational Firmware Version
SR-IOV (Available if the system supports Single-Root Virtualization)
•Recovery Firmware Version
Select Enabled for Single-Root IO Virtualization support. The options are Enabled
and Disabled.
•ME Firmware Features
Maximum Payload
•ME Firmware Status #1
Select Auto for the system BIOS to automatically set the maximum payload value
for a PCI-E device to enhance system performance. The options are Auto, 128
Bytes, and 256 Bytes.
•ME Firmware Status #2
•Current State
Maximum Read Request
•Error Code
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are Auto,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
7-24
7-25
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
ASPM Support
Chapter 7: BIOS
Serial Port 1 Configuration/Serial Port 2 Configuration
Use this item to set the Active State Power Management (ASPM) level for a PCI-E
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are Disabled and Auto.
Warning: Enabling ASPM support may cause some PCI-E devices to fail!
MMIOHBase
Use this item to select the I/O base memory size according to memory-address
mapping for the PCH chip. The base memory size must be between 4032G to
4078G. The options are 56T, 48T, 24T, 512G, and 256G.
MMIO High Size
Use this item to select the high I/O memory size according to memory-address
mapping for the PCH chip. The options are 256G, 128G, 512G, and 1024G.
CPU2 Slot1 PCI-E 3.0 x8 OPROM/CPU2 Slot2 PCI-E 3.0 x8 OPROM/CPU1
Slot3 PCI-E 3.0 x16 OPROM/CPU2 Slot4 PCI-E 2.0 x4 in x8 OPROM/CPU2
Slot5 PCI-E 3.0 x16 OPROM/CPU2 Slot6 PCI-E 3.0 x8 OPROM
Select Enabled to enable Option ROM support to boot the computer using a device installed on the slot specified by the user. The options are Disabled, Legacy,
and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a device
installed on the slot specified by the user. The options are Legacy and EFI.
Serial Port 1/Serial Port 2
Select Enabled to enable the onboard serial port specified by the user. The options
are Enabled and Disabled.
Device Settings
This item displays the base I/O port address and the Interrupt Request address of
a serial port specified by the user.
Change Port 1 Settings/Change Port 2 Settings
This feature specifies the base I/O port address and the Interrupt Request address
of Serial Port 1 or Serial Port 2. Select Auto for the BIOS to automatically assign
the base I/O and IRQ address to a serial port specified.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
The options for Serial Port 2 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
Serial Port 2 Attribute
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirection. The options are COM and SOL.
Serial
Port Console Redirection
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM/ Onboard LAN3
Option ROM/Onboard LAN4 Option ROM/Onboard Video Option ROM
COM 1
Use this option to select the type of device installed in LAN Port1, LAN Port2
or the onboard video device used for system boot. The default settings for LAN1
Option ROM is PXE, for LAN2/LAN3/LAN4 Option ROMs are Disabled ,and for
Onboard Video Option ROM is Legacy.
COM 1 Console Redirection
VGA Priority
*If the item above set to Enabled, the following items will become available for
configuration:
Use this item to select the graphics device to be used as the primary video display
for system boot. The options are Onboard and Offboard.
Super
IO Configuration
Select Enabled to enable COM Port 1 Console Redirection, which will allow a client
machine to be connected to a host machine at a remote site for networking. The
options are Disabled and Enabled.
COM1 Console Redirection Settings
Terminal Type
Super IO Chip AST2400
Use this item to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color
and function key support. Select ANSI to use the Extended ASCII Character Set.
7-26
7-27
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Bits Per second
Use this item to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Chapter 7: BIOS
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Legacy OS Redirection Resolution
Use this item to select the number of rows and columns used in Console Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
Use this item to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Use this feature to select Function Keys and KeyPad settings for Putty, which
is a terminal emulator designed for the Windows OS. The options are VT100,
LINUX, XTERMR6, SCO, ESCN, and VT400.
Parity
Redirection After BIOS Post
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Use this feature to enable or disable legacy Console Redirection after BIOS
POST (Power-On Self-Test). When the option-Bootloader is selected, legacy
Console Redirection is disabled before booting the OS. When the option-Always
Enable is selected, legacy Console Redirection remains enabled while the OS
boots up. The options are Always Enable and Bootloader.
SOL/COM2
Stop Bits
SOL/COM2 Console Redirection
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Select Enabled to use the SOL port for Console Redirection. The options are En-
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
abled and Disabled.
*If the item above set to Enabled, the following items will become available for
user's configuration:
SOL/COM2 Console Redirection Settings
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
VT-UTF8 Combo Key Support
Terminal Type
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color
and function key support. Select ANSI to use the Extended ASCII Character Set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Bits Per second
Use this feature to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
7-28
7-29
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
Chapter 7: BIOS
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS
POST (Power-On Self-Test). When this feature is set to Bootloader, legacy
Console Redirection is disabled before booting the OS. When this feature is set
to Always Enable, legacy Console Redirection remains enabled upon OS boot.
The options are Always Enable and Bootloader.
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)
The submenu allows the user to configure Console Redirection settings to support
Out-of-Band Serial Port management.
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
EMS Console Redirection
Flow Control
*If the item above set to Enabled, the following items will become available for
user's configuration:
Use this feature to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start data-sending when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Select Enabled to use a COM port selected by the user for EMS Console Redirection. The options are Enabled and Disabled.
EMS Console Redirection Settings (Available when EMS
Console Redirection is enabled)
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
Out-of-Band Management Port
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
The feature selects a serial port in a client server to be used by the Windows
Emergency Management Services (EMS) to communicate with a remote host
server. The options are COM1 (Console Redirection) and COM2/SOL (Console
Redirection).
Resolution 100x31
Terminal Type
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII character set. Select VT100+ to add color
and function key support. Select ANSI to use the extended ASCII character set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Recorder Mode
Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console
Redirection for legacy OS support. The options are 80x24 and 80x25.
7-30
7-31
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
ACPI
Bits Per Second
This item sets the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in both host computer and the client
computer. A lower transmission speed may be required for long and busy lines.
The options are 9600, 19200, 57600, and 115200 (bits per second).
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop data-sending when
the receiving buffer is full. Send a "Start" signal to start data-sending when
the receiving buffer is empty. The options are None, Hardware RTS/CTS, and
Software Xon/Xoff.
The setting for each these features is displayed:
Data Bits, Parity, Stop Bits
Trusted Computing (Available when a TPM device is
installed and detected by the BIOS)
Settings
WHEA Support
Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and provide a common infrastructure for the system to handle hardware errors
within the Windows OS environment to reduce system crashes and to enhance
system recovery and health monitoring. The options are Enabled and Disabled.
High Precision Event Timer
Select Enabled to activate the High Precision Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the dependency on other timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
NUMA (Available when the OS supports this feature)
Select Enabled to enable Non-Uniform Memory Access support to enhance system
performance. The options are Enabled and Disabled.
Configuration
Security Device Support
If this feature and the TPM jumper on the motherboard are both set to Enabled,
onboard security devices will be enabled for TPM (Trusted Platform Module) support to enhance data integrity and network security. Please reboot the system for
a change on this setting to take effect. The options are Enabled and Disabled.
TPM State
Select Enabled to use TPM (Trusted Platform Module) settings to enhance system
data security. Please reboot your system for any change on the TPM state to take
effect. The options are Disabled and Enabled.
Pending Operation
Use this item to schedule a TPM-related operation to be performed by a security
device for system data integrity. Your system will reboot to carry out a pending TPM
operation. The options are 0, Enable Take Ownership, Disable Take Ownership,
and TPM Clear.
Note: Your system will reboot to carry out a pending TPM operation.
Current Status Information
This item displays the status of the TPM support on this motherboard.
7-32
7-33
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
7-4 Event Logs
Chapter 7: BIOS
When Log is Full
Use this feature to configure Event Log settings.
Select Erase Immediately to immediately erase all errors in the SMBIOS event log
when the event log is full. Select Do Nothing for the system to do nothing when
the SMBIOS event log is full. The options are Do Nothing and Erase Immediately.
SMBIOS Event Log Standard Settings
Log System Boot Event
Select Enabled to log system boot events. The options are Disabled and Enabled.
MECI (Multiple Event Count Increment)
Enter the increment value for the multiple event counter. Enter a number between
1 to 255. The default setting is 1.
METW (Multiple Event Count Time Window)
This item is used to determine how long (in minutes) the multiple event counter
should wait before generating a new event log. Enter a number between 0 to 99.
The default setting is 60.
Change SMBIOS Event Log Settings
Note: Please reboot the system for the changes to take effect.
This feature allows the user to configure SMBIOS Event settings.
View SMBIOS Event Log
Enabling/Disabling Options
This item allows the user to view the event in the SMBIOS event log. Select this
item and press <Enter> to view the status of an event in the log. The following
categories are displayed:
SMBIOS Event Log
Select Enable to enable SMBIOS (System Management BIOS) Event Logging during system boot. The options are Enable and Disable.
Date/Time/Error Code/Severity
Runtime Error Logging Support
Select Enable to support Runtime Error Logging. The options are Enable and Disable. If this item is set to Enable, the following item will be available for configuration:
PCI-Ex (PCI-Express) Error Enable
Select Yes for the BIOS to correct errors occurred in the PCI-E slots. The options
are Yes and No.
Erasing Settings
Erase Event Log
Select Yes to erase all error events in the SMBIOS (System Management BIOS)
log before an event logging is initialized at bootup. The options are No and Yes.
7-34
7-35
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
7-5 IPMI
Chapter 7: BIOS
When SEL is Full
Use this feature to configure Intelligent Platform Management Interface (IPMI)
settings.
This feature allows the user to determine what the AMI BIOS should do when the
system event log is full. Select Erase Immediately to erase all events in the log when
the system event log is full. The options are Do Nothing and Erase Immediately.
Note: After making changes on a setting, be sure to reboot the system for
the changes to take effect.
BMC Network Configuration
The following items will be displayed:
•IPMI LAN Selection
•IPMI Network Link Status
Update IPMI LAN Configuration
Select Yes for the system BIOS to automatically reset the following IPMI settings
at next system boot. The options are Yes and No.
BMC (BaseBoard Management Controller) Firmware Revision
This item indicates the BMC firmware revision used in your system.
IPMI Status
This item indicates the status of the IPMI firmware installed in your system.
System Event Log
Configuration Address Source (Available when the item above - Update
IPMI LAN Configuration is set to Yes)
Use this item to select the IP address source for this computer. If Static is selected,
you will need to know the IP address of this computer and enter it to the system
manually in the field. If DHCP is selected, AMI BIOS will search for a DHCP (Dynamic Host Configuration Protocol) server attached to the network and request
the next available IP address for this computer. The options are DHCP and Static.
Station IP Address
Enabling/Disabling Options
This item displays the Station IP address for this computer. This should be in decimal
and in dotted quad form (i.e., 192.168.10.253).
SEL Components
Select Enabled to enable all system event logging support at bootup. The options
are Enabled and Disabled.
Erasing Settings
Subnet Mask
This item displays the sub-network that this computer belongs to. The value of each
three-digit number is separated by dots and it should not exceed 255.
Station MAC Address
Erase SEL
Select Yes, On next reset to erase all system event logs upon next system reboot.
Select Yes, On every reset to erase all system event logs upon each system reboot.
Select No to keep all system event logs after each system reboot. The options are
No, Yes, On next reset, and Yes, On every reset.
7-36
This item displays the Station MAC address for this computer. Mac addresses are
6 two-digit hexadecimal numbers.
Gateway IP Address
This item displays the Gateway IP address for this computer. This should be in
decimal and in dotted quad form (i.e., 192.168.10.253).
7-37
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Chapter 7: BIOS
7-7 Boot Settings
7-6 Security Settings
This menu allows the user to configure the following security settings for the
system.
Use this feature to configure Boot Settings:
Boot Configuration
Password Check
Setup Prompt Timeout
Select Setup for the system to prompt for a password upon entering the BIOS setup
utility. Select Always for the system to prompt for a password at bootup and upon
entering the BIOS Setup utility. The options are Setup and Always.
Use this item to indicate how many seconds the system shall wait for the BIOS setup
activation key to respond before the system starts to boot. The default setting is 1.
Boot Mode Select
Administrator Password
Use this feature to set the administrator password which is required before entering
the BIOS setup utility. The length of the password should be from 3 characters
to 20 characters long.
User Password
Use this feature to set the user password which is required to enter the BIOS
setup utility. The length of the password should be from 3 characters to 20 characters long.
Use this item to select the type of device to be used for system boot. The options
are Legacy, UEFI, and Dual.
Fixed Boot Order Priorities
This option prioritizes the order of bootable devices from which the system will boot.
Press <Enter> on each entry from top to bottom to select devices.
•Dual Boot Order #1
•Dual Boot Order #2
•Dual Boot Order #3
•Dual Boot Order #4
•Dual Boot Order #5
•Dual Boot Order #6
7-38
7-39
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
•Dual Boot Order #7
Chapter 7: BIOS
7-8 Save & Exit
•Dual Boot Order #8
Select the Save & Exit tab from the BIOS setup screen to configure the settings
below.
•Dual Boot Order #9
•Dual Boot Order #10
•Dual Boot Order #11
•Dual Boot Order #12
•Dual Boot Order #13
•Dual Boot Order #14
•Dual Boot Order #15
Delete Boot Option
Use this item to select a boot device to delete from the boot priority list.
Delete Boot Option
Select the target boot device to delete.
Hard Disk Drive BBS Priorities
Discard Changes and Exit
Select this option to quit the BIOS setup without making any permanent changes
to the system configuration, and reboot the computer. Select Discard Changes and
Exit from the Exit menu and press <Enter>.
Save Changes and Reset
•Legacy Boot Order #1
When you have completed the system configuration changes, select this option to
leave the BIOS setup utility and reboot the computer for the new system configuration parameters to take effect. Select Save Changes and Exit from the Exit menu
and press <Enter>.
Network Drive BBS Priorities
•Legacy Boot Order #1
Save Options
UEFI Application Boot Priorities
•UEFI Boot Order #1
Save Changes
When you have completed the system configuration changes, select this option to
save all changes made. This will not reset (reboot) the system.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS setup utility.
Restore Defaults
Select this item and press <Enter> to load the manufacture default settings which
are designed for maximum system performance but not for maximum stability.
7-40
7-41
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Save As User Defaults
Select this item and press <Enter> to save the current BIOS settings as user's
default settings for future use.
Restore User Defaults
Select this item and press <Enter> to retrieve user-defined settings that were previously saved for future use.
Boot Override
This feature allows the user to override the Boot priorities sequence in the Boot
menu and immediately boot the system with another device specified by the user.
This is a one-time override.
7-42
Appendix A: BIOS Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed at each
system boot, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue to
boot. The error messages normally appear on the screen.
Fatal errors will not allow the system to continue with bootup procedure. If a fatal
error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the corresponding error.
Motherboard BIOS Error Beep Codes
Beep Code/LED
Error Message
Description
1 beep
Refresh
Ready to boot
5 short beeps + 1 long
beep
Memory error
No memory detected in the
system
5 beeps
No Con-In or No
Con-Out devices
Con-In includes USB or
PS/2 keyboard, PCI or Serial
Console Redirection, IPMI
KVM or SOL.
Con-Out includes Video Controller, PCI or Serial Console
Redirection, IPMI SOL.
1 beep per device
Refresh
1 beep or each USB device
detected
A-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Notes
A-2
Appendix B: System Specifications
Appendix B
System Specifications
Processors
Single or dual Intel® Xeon E5-2600 (v3/v4) Series processors
Note: Please refer to our web site for a complete listing of supported processors.
Chipset
Intel C612 chipset
BIOS
16 Mb AMI® SPI Flash ROM
Memory Capacity
Twenty-four DIMM sockets supporting up to 3 TB of ECC LRDIMM (Load
Reduced DIMMs) or 1.5 TB of ECC RDIMM (Registered DIMMs) DDR42400/2133/1866/1600 memory
Note: see Section 5-6 for details.
Drive Bays
Twenty-four hot-swap drive bays to house SATA or SAS hard drives
PCI Expansion
One PCI-E 3.0 x16 and three PCI-E 3.0 x8 expansion cards (the RAID controller
card and JBOD ports occupy two onboard PCI slots)
Serverboard
X10DRi-T4+ (Extended ATX form factor)
Dimensions: 13.68 x 13.05 in (347.5 x 331.5 mm)
Chassis
SC846BE1C-R920B (4U rackmount)
Dimensions: (WxHxD) 17.2 x 7 x 26.5 in. (437 x 178 x 673 mm)
B-1
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
Appendix B: System Specifications
Notes
Weight
Gross Weight: 52 lbs. (23.6 kg.)
System Cooling
Three 8-cm system fans and two 8-cm exhaust fans
System Input Requirements
AC Input Voltage: 100 - 240V AC auto-range
Rated Input Current: 11 - 4.5A max
Power Supply
Rated Output Power: 920W (Part# PWS-920P-SQ)
Rated Output Voltages: +12V (75A), +5Vsb (4A)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5% to 95% (non-condensing)
Regulatory Compliance
Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/-3-3,
CISPR 22 Class A
Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3,
EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)
Safety: CSA/EN/IEC/UL 60950-1 Compliant, UL or CSA Listed (USA and
Canada), CE Marking (Europe)
California Best Management Practices Regulations for Perchlorate Materials:
This Perchlorate warning applies only to products containing CR (Manganese
Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate”
B-2
B-3
SUPERSTORAGESYSTEM 6048R-E1CR24N User's Manual
(continued from front)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to
result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous
applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
B-4
Download PDF
Similar pages