IR BULLET IP CAMERA SERIES

IR BULLET
IP CAMERA SERIES
OPERATION GUIDE
Please read instructions thoroughly before operation and retain it for future reference.
m3650l_3452t_2452t_2452_2451t_2453_2200_V1.2
IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the
European law on the Restriction of Hazardous Substances (RoHS) directive, which means
our manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product
must be collected separately at the product end-of-life. This applies to your product and
any peripherals marked with this symbol. Do not dispose of these products as unsorted
municipal waste. Contact your local dealer for procedures for recycling this equipment.
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device mat not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Trademark Acknowledgements
iPad® & iPhone® are the registered trademarks of Apple Inc.
Android™ is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.
Microsoft®, Windows® & Internet Explorer® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume
any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of
this manual is subject to change without notice.
This product doesn’t have a standby / off mode.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING
MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY
MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL
AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which
are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public
License (“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the
copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. To get the codes, please write to
marketing@avtech.com.tw.
TABLE OF CONTENTS
1. OVERVIEW......................................................................................................................................... 1 1.1 Product Features....................................................................................................................................... 1 1.2 Package Content....................................................................................................................................... 1 1.3 Cable Overview ......................................................................................................................................... 1 1.4 External Alarm Connection........................................................................................................................ 2 2. CAMERA ACCESS WITH INTERNET EXPLORER............................................................................ 3 2.1 Camera Login............................................................................................................................................ 3 2.2 Control Panel Overview ............................................................................................................................ 3 2.3 Digital PTZ (DPTZ) Operations ................................................................................................................. 5 2.4 Event Record Search & Playback ............................................................................................................. 7 3. CAMERA CONFIGURATIONS............................................................................................................ 8 3.1 System configuration menu....................................................................................................................... 8 3.2 Network ................................................................................................................................................... 10 3.2.1 Network ..........................................................................................................................................................10 3.2.2 QoS ................................................................................................................................................................10 3.2.3 DDNS .............................................................................................................................................................10 3.2.4 SNTP..............................................................................................................................................................10 3.2.5 FTP................................................................................................................................................................. 11 3.2.6 MAIL ............................................................................................................................................................... 11 3.2.7 SMS................................................................................................................................................................12 3.2.8 Filter ...............................................................................................................................................................13 3.2.9 UPnP / Bonjour...............................................................................................................................................13 3.2.10 RTP ..............................................................................................................................................................14 3.2.11 SNMP ...........................................................................................................................................................15 3.2.12 IEEE 802.1X (For selected models only) .....................................................................................................16 3.2.13 Network Share .............................................................................................................................................17 3.2.14 Network Failure Detection............................................................................................................................17 3.3 Camera ................................................................................................................................................... 17 3.3.1 Camera...........................................................................................................................................................17 3.3.2 Video ..............................................................................................................................................................18 3.3.3 ROI (For selected models only) .....................................................................................................................18 3.3.4 Color...............................................................................................................................................................18 3.3.5 Audio ..............................................................................................................................................................19 3.3.6 Advanced........................................................................................................................................................19 3.3.7 Privacy Mask (For selected models only) ......................................................................................................20 3.4 VA (For selected models only)................................................................................................................. 21 3.4.1 TA ...................................................................................................................................................................21 3.5 EVENT .................................................................................................................................................... 21 3.5.1 Event ..............................................................................................................................................................21 3.5 Record..................................................................................................................................................... 21 3.5.1 Record............................................................................................................................................................21 3.5.2 Record Timer..................................................................................................................................................22 3.6 Storage.................................................................................................................................................... 22 3.6.1 Memory ..........................................................................................................................................................22 3.7 Trigger ..................................................................................................................................................... 22 3.7.1 Trigger ............................................................................................................................................................22 3.7.2 Snapshot ........................................................................................................................................................24 3.8 General ................................................................................................................................................... 24 3.8.1 General...........................................................................................................................................................24 3.8.2 Time................................................................................................................................................................25 3.8.3 Server Log......................................................................................................................................................25 3.8.4 Online .............................................................................................................................................................26 3.8.5 Account...........................................................................................................................................................26 3.8.6 Google Maps ..................................................................................................................................................27 3.8.7 Maintenance...................................................................................................................................................27 APPENDIX 1 PRODUCT SPECIFICATIONS........................................................................................ 29 APPENDIX 2 BIT RATE TABLE FOR REFERENCE ............................................................................ 33 APPENDIX 3 POE CONNECTION ....................................................................................................... 35 APPENDIX 4 API ID APPLICATION FOR SMS MESSAGING.............................................................. 36 APPENDIX 5 Q&A ................................................................................................................................ 38 APPENDIX 6 RECORDING TIME TABLE ............................................................................................ 39 APPENDIX 7 PREREQUISITES FOR NETWORK SHARE.................................................................. 40 A7.1 Check PC IP Address ........................................................................................................................... 40 A7.2 Create "Administrator" Account............................................................................................................. 40 A7.3 Share Folder ......................................................................................................................................... 41 1. OVERVIEW
1.1 Product Features
 Easy network setup with your iOS / Android OS
 ONVIF standard supported to simplify system integration
 POE (Power-over-Ethernet) support to eliminate the use of power cables and reduce installation costs
 IR LEDs built-in for night surveillance
 External alarm I/O device connection
 Line in / out jacks available for audio transmission
 DWDR to increase image recognizability in overexposure and dark areas.
 Remote Surveillance
-- Full compatibility with iOS & Android OS, and Internet Explorer on Windows operating system
1.2 Package Content

Standard Package
 IR Camera

 Quick Guide
Optional Accessories
 Screws & wall plugs
 Wrench
 Sun shield
 screw for sun shield
 Installation sticker
 Waterproof kit
1.3 Cable Overview
Cable
Description
Power cable
Connect to DC12V power supply.
Note: The power adapter is optional.
RJ45 network cable
Connect it to the supplied RJ45 cable extender adapter for cable extension, and prepare another RJ45
network cable with suitable length for your connection.
GND
Ground wire, used for reset default or external device connection.
Alarm-in
Reserved for connecting to an external alarm device. For details, please refer the user manual of your alarm
device.
Alarm-out
Reserved for connecting to an external alarm device. For details, please refer the user manual of your alarm
device.
RESET
Remove the insulating coating of this wire, and twist it with a ground wire together to reset default. This will
reset all parameters, including the IP address to factory default settings.
Note: Disconnect power before twisting these two wires together, and connect to power again for
reset default.
Line in (Blue)
Support microphone connection.
Line out (Green)
Support speaker connection.
1
1.4 External Alarm Connection
This camera supports external I/O device connection for easy connection.
Below shows you how to connect an external device to this camera.
2
2. CAMERA ACCESS WITH INTERNET EXPLORER
This network camera can be accessed via Microsoft Internet Explorer and iOS / Android mobile devices with our
self-developed program “EagleEyes” installed depending on different using situations.
Before using the camera, make sure you have configured the network settings, and the network connection is fine.
For network configurations, please refer to:

“ADVANCED NETWORK SETUP” downloadable from www.surveillance-download.com/user/m650.swf.
2.1 Camera Login
Step1: Open your web browser, and key in http://ipaddress:portnum in the URL address box.
For example, for the IP address 60.121.46.236 and port No. 888, please key in ”http://60.121.46.236:888” into
the URL address box, and press “Enter”.
Step2: In the login page, key in the user name and password, and enter the security code from the image below if any.
Then, click “LOGIN”.
Step3: The wizard is then started.
‧ To skip the wizard and directly access the camera live view, click “Close”.
‧ To directly access the camera live view without starting the wizard for the login next time, check “Do not start wizard at login”.
Note: If you’re prompted to install “VLC player”, “Software” and “H264 Streaming Viewer”, please
agree to proceed the installation.
Step5: When the login is successful, the live view is shown.
2.2 Control Panel Overview
Note: The buttons available depend on the device you have and the user level used to log in.
3
User Level
Description
Live
Supervisor / Power User
/ Normal User / Guest
Switch to the live view page.
o Backup
Supervisor / Power User
*
Function
Icon
F
r
DPTZ
Supervisor / Power User
/ Normal User
Config.
Supervisor / Power User
s
e
--
e
Supervisor / Power User
/ Normal User / Guest
c
Switch to the DPTZ configuration page.
For details, please refer to “2.3 Digital PTZ (DPTZ) Operations” at page 4.
Switch to the system configuration page. The functions available for
“Supervisor” and “Power User” are different.
Select the image player from the drop-down list:
 ActiveX
 QuickTime
QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime
installed in your operating system before selecting “QuickTime”. When it is
selected, you will be promoted to enter the user name and password to access
the camera.
t
e
 VLC
d Quality
Video Profile
--
Supervisor / Power User
/ Normal User
Click & drag the slider to select the video quality:
BASIC / NORMAL / HIGH / BEST.
--
Supervisor / Power User
/ Normal User
Select the pre-defined video set from the drop list. The video set could be
configured in “Config” -> “Camera” -> “Video”.
Supervisor / Power User
/ Normal User
Click to take a snapshot of the current view on a new window. Right click
on the picture and re-save it to the location you want.
o
Snapshot
d
Supervisor / Power User
/ Normal User
e Live View Size:
l
s
For details, please refer to “2.4 Event Record Search & Playback’ at page 6.
For more details, please refer to “3.1 System configuration menu” at page 8.
l Live player
m
Enter the event record list for video playback.
Click to display the image in full screen.
To exit the full screen mode, press “Esc” on your keyboard.
Full Screen
This icon appears only when the selected resolution is 640 x 480 or above.
o
The QVGA resolution is resized to fit into the current live view size.
Double size
This icon appears only when the selected resolution is 320 x 240.
n
l
The current live view size is the same as the selected resolution.
Normal Size
This icon appears only when the selected resolution is 1280 x 720 or above.
y
The selected resolution is resized to fit into the current live view size.
Fit to screen
This icon appears only when the selected resolution is 1280 x 720 or above.
Click and hold the movable square on the left bottom corner of the live view
to move
No Scale
This icon appears only when the selected resolution is 1280 x 720 or above.
Audio Switch
/
Alarm Out
Microphone
/
Max. Zoom-in / out*
Focus Assist*
Click to switch the audio-in on / off.
Supervisor / Power User
/ Normal User
Click to force your alarm-out device to work. For example, when your
alarm device is a buzzer, click this button and your buzzer will start to
sound even if there’s no alarm event.
Supervisor
Click to switch the audio-out on / off.
Supervisor / Power User
/ Normal User
DPTZ*
Zoom-in / out*
Supervisor / Power User
/ Normal User
/
Supervisor / Power User
/ Normal User
/
Supervisor / Power User
/ Normal User
Supervisor / Power User
/ Normal User
Click to enable the zoom-in / out function. To move the image in the
zoom-in mode, simply click on where you want to see in the live view.
For vari-focal models only.
Click to zoom in / out the current image.
This function is available only when DPTZ is enabled.
Click to zoom in the image to the largest / zoom out the image to its
original size.
This function is available only when DPTZ is enabled.
Click to help you determine whether the image clearness is adjusted well
when you're adjusting your camera focus. Two values will be calculated
and shown as “XX / YY”.
 YY is the best focus value for your current camera view
 XX is your current focus value
When XX is closer to YY, the clearer and sharper images you’ll get for your
camera view.
4
2.3 Digital PTZ (DPTZ) Operations
This camera has PTZ capability, i.e. digital PTZ (hereafter called “DPTZ”), for wide area monitoring.
STEP1: Click “DPTZ” to show the DPTZ control panel.

Type1
STEP2: Select the functions when needed:
FUNCTION
ICON
DESCRIPTION
Moving panel
--
Move the picture.
Resolution
--
Select the video resolution for the DPTZ function. Only “VGA” and “QVGA” are available.
Take snapshots
Click to take a snapshot of the current view on a new window. Right click on the picture and re-save it to the
location you want.
Alarm Out
Click to force your alarm-out device to work. For example, when your alarm device is a buzzer, click this button
and your buzzer will start to sound even if there’s no alarm event.
Audio On / Off
/
Click to switch the audio-in on / off.
Microphone*
/
Click to switch the audio-out on / off.
5

Type 2
FUNCTION
Moving panel
ICON
--
DESCRIPTION
When
is selected, the moving control panel will be shown to move the picture after zoom-in is
performed.
Click to take a snapshot of the current view on a new window. Right click on the picture and re-save it
to the location you want.
Take snapshots
Zoom in / out
/
Click
Max. zoom in / out
/
once to enlarge the picture to the max zoom ratio by 16X, and click
Click
picture ratio to 1X.
Normal Size
once to enlarge the picture by 1X, and click
once to restore the zoom ratio by 1X.
once to restore the
The current live view size is the same as the selected resolution.
This icon appears only when the selected resolution is 1280 x 720 or above.
Scale
Click and hold the movable square on the left bottom corner of the live view to move
This icon appears only when the selected resolution is larger than the current live view size.
6
2.4 Event Record Search & Playback
Note: To save more recorded data, it’s recommended to use this camera with a compatible NVR.
/
Previous / Next Hour
Click to jump to the next / previous time interval in an hour, for example, 11:00 ~ 12:00 or 14:00
~ 15:00, and start playing the earliest event video clip recorded during this whole hour.
Fast Forward
Increase the speed for fast forward. Click to get 2X, 4X, 8X & 16X speed forward eventually.
Fast Rewind
Increase the speed for fast rewind. Click to get 2X, 4X, 8X & 16X speed rewind eventually.
Play
Click to play the current video clip.
Pause
Click to pause the video playback.
Stop
Click to stop the video playback.
Step
In the pause mode, click to get one frame forward.
Audio
Click to mute the playback if necessary, and click again to restore.
Click to download the current video clip to the specified path in your PC.
Download
The downloaded video can only be opened by our own video player. Please go to “General” → “Maintenance” to
download the video player, or get the player from the CD supplied with the sales package.
7
3. CAMERA CONFIGURATIONS
Users can further configure this network camera by accessing via Internet Explorer.
3.1 System configuration menu
Click “Config.” to enter the configuration page.
The functions are categorized into seven menus: Network, Camera, VA, Record, Storage, Trigger and General.

For details about “Network”, please refer to “3.2 Network” at page 10.

For details about “Camera”, please refer to “3.3 Camera” at page 16

For details about “VA”, please refer to “3.4 VA (For selected models only)” at page 21

For details about “Record”, please refer to “3.5 Record” at page 21.

For details about “Storage”, please refer to “3.6 Storage” at page 22.

For details about “Trigger”, please refer to “3.7 Trigger” at page 22.

For details about “General”, please refer to “3.8 General” at page 24.
Main Menu
Sub-Menu
Reference
Network
Network
Configure network settings.
QoS
Limit the data flow for live streaming.
DDNS
Enter DDNS information when the network type is PPPOE or DHCP.
SNTP
Synchronize your camera time with the networked computer systems.
FTP
Enter the FTP information for event notifications when “FTP” is chosen in “Trigger” →
“Trigger”.
Mail
Enter Email information for event notifications when “Email” is chosen in “Trigger” → “Trigger”.
SMS
Enter text messaging information for SMS notifications when “SMS” is chosen in “Trigger” →
“Trigger”.
Filter
Choose to permit or block the IP address(es) which can access this camera.
*Suitable for Windows-based operating system.
UPnP
Allow this camera to be detected among devices within the same network area for easy and
quick usage.
*Suitable for Apple Mac-based operating system.
Bonjour
Camera
Allow this camera to be detected among devices within the same network area for easy and
quick usage.
RTP
Set the parameters for video data transmission when you’re using multimedia other than web
browsers and Video Viewer for remote access.
SNMP
Configure SNMP to remotely manage network devices.
IEEE 802.1X*
The settings here enable the camera to access a network protected by 802.1X/EAPOL
(Extensible Authentication Protocol Over LAN).
Network Share
Assign a location in the LAN environment to save the snapshot of events when “Network
Share” is chosen in “Trigger” → “Snapshot”.
Network Failure Detection
Configure this camera to check the network connection of other device periodically, and send
notifications via Email or FTP for disconnection events.
Camera
1. Rename the camera.
2. Change the place where the camera name is shown on the screen.
Video
Adjust video-related settings in different video format.
ROI*
Select a specific area to reinforce the image quality of that area.
Color
Adjust the color performance.
Audio
Adjust the audio volume of the microphone and speaker.
Advanced
Adjust the camera parameters if necessary.
Privacy Mask*
Cover certain areas on the camera image.
VA*
TA*
This function should be used with the mini-guard control switch for alarm system integration.
For details, please check with your distributor or installer.
ONVIF
Event
This function is used to integrate the functions of event and alarm detection when this camera
has to work with other ONVIF-compliant device.
Record
Record
Configure the record function.
Record Timer
Schedule external alarm recording.
Memory
Check the current storage capacity and clear all recorded data when needed.
Storage
*Selected models only
8
Main Menu
Sub-Menu
Trigger
Trigger
Reference
1. Enable / disable the motion detection.
2. Set the motion detection area.
3. Configure how the camera reacts for any event.
Snapshot
Schedule the camera to take snapshots periodically or at a specific time, and send to E-Mail,
FTP and / or Network Share for backup. Time-lapse recording could also be configured here.
1. Select the language of the web browser.
General
General
2. Check the MAC address of the camera.
3. Lock camera access after the specified time.
Time
Set daylight saving time and the current time.
Server Log
Check the system event logs.
Online
Check the current online user(s).
Account
Google Maps
1. Create a new user account with different access privilege.
2. Modify or delete an existing user account.
Allow you to know where the network camera is.
1. Check the current firmware version and upgrade your camera.
Maintenance
2. Copy system configurations.
3. Reboot the camera.
4. Download the video player to play the recorded data.
*Selected models only
9
3.2 Network
3.2.1 Network
You can set the network configuration of the network camera depending on your network type.
For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m650.swf.
3.2.2 QoS
QoS, Quality of Service, is the ability to control the data flow for real-time streaming. This function is important if
your network bandwidth is insufficient and you have other devices to share the network bandwidth.
Check “QoS Enable”, and set the max. upload rate from 256 to 10240 kbps.
3.2.3 DDNS
Select “On” when the selected network type in “Network” is “PPPOE” or “DHCP”.
For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m650.swf.
3.2.4 SNTP
SNTP (Simple Network Time Protocol) is used to synchronize your camera time with the networked computer..
Function
Description
GMT
Once users choose the time zone, the network camera will adjust the local area time of the system
automatically.
NTP Server
Simply use the default SNTP server (For example, tock.stdtime.gov.tw) or change to another server with
which users are familiar.
Sync. Period
Select “Daily” to synchronize the camera time with the network time every day or “None” to turn off this
function.
Sync
Click and the network camera will synchronize the time with the network time.
10
3.2.5 FTP
Enter the detailed FTP information and click “Save” to confirm. The information you set here will be applied
when “FTP” is selected in “Trigger” → “Trigger”.
3.2.6 MAIL
Enter the detailed e-mail information and click “Save” to confirm. The information you set here will be applied
when “Email” is selected in “Trigger” → “Trigger”.
Function
Description
SMTP Server
Enter the SMTP server address provided from your e-mail system supplier.
Port
Enter the port number provided from your e-mail system supplier. If this column is left blank, the e-mail server will use
port 25 to send e-mails.
Mail From
Enter the name of the sender.
SSL Encryption
Select “Yes” if your e-mail server is using SSL encryption to protect your e-mail content from unauthorized access.
Verify Password
Some mail servers are required to verify the password. Please enter the “user name” and “password”.
Subject
Enter the subject for the E-Mail.
E-Mail Address List
Add the e-mail address(s) of the assigned recipient(s).
Test
When all information is entered, click “Test Mail” to try if the receipt.
11
3.2.7 SMS
Note: Before using this function, you need to apply an account and get an API ID from the mobile
messaging company, such as Clickatell and EVERY8D. For details, please refer to “APPENDIX 4
API ID APPLICATION FOR SMS MESSAGING” at page 36.
Enter the detailed information needed for text messaging, and click “Save” to confirm. The information you set
here will be applied when “SMS” is selected in “General” → "Trigger".
Function
Description
System
The text messaging service provider is Clickatell.
User name / Password
Enter the account user name and password you created in Clickatell.
API ID
Enter the API ID you applied from Clickatell.
Recipient
Click “Add” to enter the phone number, including the country code, to receive the text
message. Five sets of phone numbers are allowed.
Transfer Interval
Set the interval time in minutes between two-message sending.
The options are 0, 15, 30 & 60.
Reset Counter
Click to restart the text messaging, and the SMS will be sent after the specified time interval
since you click this button.
Message
Enter the text content (up to 70 characters) you want to send with the text message.
Test
To know whether your SMS setting is correct, click this button to immediately send a SMS to
your phone.
Note: This testing is not free and you will be charged for SMS sending base on your
local rate.
12
3.2.8 Filter
Choose to permit or block the IP address(es) which can access this camera, and click “Save” to confirm.
Function

Description
Filter Configuration
Error Count
Set the maximum count for login failure. When the maximum count is reached, the IP address trying to access the
network camera will be locked.
Error Lock Time
Set the lock time in minutes when the maximum count of error login for an IP address is reached.
Echo Request
Select “Non-Block” to allow other users to use the ping command to detect the IP address of your network camera, or
“Block” to deny the ping command request.

IP/MAC Filter Configuration
IP/MAC Filter
Choose to enable or disable the filter function.
IP/MAC Filter Policy
If “Enable” is selected, choose whether you want to permit (Allow) or block (Deny) the IP address list below.

IP/MAC Filter Rules
‧
‧
Rule
To add an item to the IP address list, key in the IP address in “Rule”, and click “Add”.
To remove an existing item in the IP address list, click the item you want to remove, and click “Delete”.
3.2.9 UPnP / Bonjour
“UPnP” stands for “Universal Plug and Play”, which allows devices to connect seamlessly in the home and
corporate environments and simplify installation of computer components, and is only suitable for Microsoft
Windows-based operating system.
“Bonjour” functions the same as “UPnP”, but it’s only suitable for Apple Mac-based operating system.
 UPnP
 Bonjour
Check “Enable” to allow the network camera to be detected among devices within the same network area, and
set the identification name of the camera in “Friendly name”.
When this function is activated, the other PC within the same domain as this camera will be able to search this
camera in:

“Network Neighbor” with the identification name set in “Friendly name” for Windows-based PC, or

“
” (finder) or “Bookmark” with the identification name set in “Device Name” for Mac-based PC.
13
Double-click it to quickly open the web browser for camera access.
Port Mapping (Available only in UPnP)
This function can eliminate the need to additionally access the router for port forwarding.
For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m650.swf.
Note: Before using this function, make sure your router supports UPnP, and this function is enabled. If
not, please access your router additionally for port forwarding.
When “Port Mapping” is set to “Enable”, the system will automatically assign an IP address or port number for
you if no IP address or port number is entered.
Note: When the configurations are saved successfully, you’ll see a message indicating the IP address
and port number assigned to this network camera.
3.2.10 RTP
The Real-time Transport Protocol (RTP) is an Internet protocol standard to manage the real-time transmission of
multimedia, such as VLC player.
The media player you want to use for remote access must support RTP transmission for this function to work
normally.
Note: When you’re about to end the remote access, please press the stop button on your media player
first, and then close the program. This is to ensure the server receives the stop command, and
also help to protect the server from redundant data transmission.
14
Function

Description
Port Range
The port range used by RTP is limited, and preserving 100 ports between the start port and end port is necessary.
Start Port
The range of the start port is 1024 ~ 65434.
End Port
The range of the end port is 1124 ~ 65534.

Video
Address and port for
video transmission
Set a specific address and port for multicast of profile 1 ~ 4.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.

Audio
Address and port for
audio transmission
Set a specific address and port for multicast of audio.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.
3.2.11 SNMP
SNMP, Simple Network Management Protocol, is used to facilitate the exchange of management information
between network-attached devices, and network administrators could use it to monitor those devices.
The SNMP consists of three basic components:

Network-management systems (NMSs) to monitor and control the managed devices.

Managed devices as network nodes to save all network and management information, such as routers, access
servers, switches, bridges, hubs, etc.

Agents as network management software modules on managed devices to provide the status of managed devices
to NMSs.
Note: Before configuring SNMP settings, make sure your NMS is enabled first.
Enable SNMP V1 / V2C
Select “Yes” to enable this function, and enter the names of “Read community” and “Write community” based on
your NMS configurations.
To enable “Traps” to notify the management station of important events, choose “V1” or “V2C” in “Enable”, enter
the address and community name, and select the event type(s) needed.
15
Enable SNMP V3
SNMP V3 has a higher security level than SNMP V1 / V2C to allow configuring the authentication password and
encryption password.
Choose “Read/Write Security name” or “Read only Security name” based on your NMS settings, and enter the
community name. Then, select the authentication type from “MD5” or “SHA”, and enter the password for
authentication and encryption. The password length is from 8 to 31 characters.
3.2.12 IEEE 802.1X (For selected models only)
The settings here enable the camera to access a network protected by 802.1X/EAPOL (Extensible
Authentication Protocol Over LAN).
Note: For authentication to work properly, it's important to synchronize the time in the camera with an
NTP server.
Before using this function, make sure:

The switch and RADIUS server you have in the LAN environment supports IEEE 802.1X, and IEEE 802.1X
settings are enabled.

You’ve applied a digital certificate from a Certificate Authority which can be validated by a RADIUS server,
and the identity and password used.
Then, follow the steps below:
Step1: Connect this camera to a PC or laptop directly, and go to its login page to log in.
Note: To know how to connect the camera to a PC or laptop directly, please check “4 Modem / Hub +
Modem” in “ADVANCED NETWORK SETUP”.
Step2: Log into the camera, and go to “Config”  “Network”  “IEEE 802.1X”. Enable this function, and select
the EAP method you want to use.
Note: This camera supports “EAP-PEAP”, “EAP-TLS” and “EAP-TTLS”.
Step3: Enter the identity and password you get from the Certificate Authority, and select the EAPOL version
used in your switch.
Step4: Upload the certificate(s) issued by the Certificate Authority, and save.
Step5: Disconnect the camera from your PC or laptop, and connect it to the switch in the LAN environment you
want to use IEEE 802.1x, and the camera will start the authentication later.
16
3.2.13 Network Share
This function is used to assign a location in the LAN environment to save the snapshot of events.
Note: This function is available only for Windows operating systems.
The information you set here will be applied when “Network Share” is selected in “Trigger” → “Snapshot” →
“Storage Mode”.
To use this function, make sure:



A PC is installed in the same LAN environment as this camera, and you know the IP address of the PC.
A PC account is created as “Administrator” with a user name and password.
A folder in the PC is opened as shared to the user account you assigned.
Note: Please check “APPENDIX 7 PREREQUISITES FOR NETWORK SHARE” at page 40 for more details.
Enable this function, and enter the address of the PC, the folder being shared, and the user name and password
to access the PC. If the information is all correct, you'll see a check in the “Status” column, and you’re ready to
go to “Trigger” → “Snapshot” for further configurations.
3.2.14 Network Failure Detection
Configure this camera to check the network connection of other device periodically, and send notifications via
Email or FTP for disconnection events.
3.3 Camera
3.3.1 Camera
In this menu, you can set the camera title, OSD display, and location to save snapshots.
Note: The actual functions shown depend on the model you have.

Type1

17
Type2
3.3.2 Video
Adjust video-related settings in different video format.

“Quality” is related to image clearness.

“FPS” is related to the fluency of the video. The more the FPS, the more fluent the video.

“Max Bit Rate” is the maximum limitation of data transmission in the selected image format and resolution.
Note: QQVGA is for mobile surveillance only.
3.3.3 ROI (For selected models only)
ROI, Region of Interest, is used to reinforce the image quality of the selected area(s). Users could specify two
areas in the camera view.
3.3.4 Color
Adjust the color performance from Brightness, Contract, Saturation, and Hue. Click and drag the slider to
preview the color change on the right side of this page and adjust the image color.
To restore the default values, click “Back to Default”.
18
3.3.5 Audio
Drag the slider to adjust the volume of the microphone and speaker.
3.3.6 Advanced
Adjust the camera parameters if necessary.
Note: The functions available depend on the model number used.
Item
Description
Fixed Shutter*
Shutter Speed is a function that can adjust the duration of the electronic shutter to produce optimum image quality. Select the
shutter speed suitable for your environment.
Slow Shutter
Speed
Select the slow shutter speed suitable for your environment.
A slower shutter speed in dark conditions will help to produce a brighter image, but will produce fewer frames per second,
which may cause images to get blurry during motion.
Exposure Control
This function is used to synchronize the shutter time to the fluorescent light to suppress image flickering.
Exposure Value*
Drag the slider to adjust the exposure level from 0 ~ 4. The higher the value, the more light to let into the camera.
Mirror
Select “ON” to rotate the images horizontally based on your installation situation when necessary.
Flip
Select “ON” to rotate the image 180° when necessary.
Denoise
Click and drag the slider to adjust the level to decrease the noise shown in the dark environment. The higher the value, the
higher the denoise level. 0 means off.
IR Control
Select “Auto” to automatically enable IR LEDs at night or in the dark environment, “On” to always enable IR LEDs, or “OFF”
to disable this function.
IR Extend Time*
Set the delay time from 1 ~ 60 in second after which the day and night switch is made, or select 0 to disable this function.
This is used for the environment where the light condition may change suddenly and usually last for a short time, for
example, the entrance of a parking lot. It may cause the day & night mode switching constantly and damage the camera.
With this function, the camera will delay the mode switch at night since the light change is temporary and unnecessary to pay
attention.
IR Turn On Level*
Select the level for IR light to activate. 0 means off.
White Balance
Process the current image to retain color balance over a color temperature range.
Sharpness
Sharpness enhances the clarity of image detail by adjusting the aperture and sharpening the edges in the pictures.
Hold and drag the slider to adjust the level of sharpness. The higher the value, the sharper the image.
Digital WDR
Digital WDR is used to simulate the effect of WDR when users need to increase image recognizability in overexposure and
dark areas. 0 means off.
19
Item
Description
Day and Night*
This function is used to configure the day and night mode:

Day - Always stay in the day mode (color).

Night - Always stay in the night mode (B/W).

Time – Select this option, and click “Day and Night” in blue to enable and set a schedule to enable day and night mode. The selected
time (yellow) will be in the day mode, and the unselected time will be in the night mode.

Sensor – Use the built-in light sensor for day and night detection.

Digital Input N.O. – (Used with Alarm In) Normally stay in the day mode, and switch to the night mode when the alarm is triggered.

Digital Input N.C. – (Used with Alarm In) Normally stay in the night mode, and switch to the day mode the when alarm in triggered.
Defog*
Select ”ON” or ”Auto” to enable the defog function in poor weather conditions such as fog, smog or smoke. The captured
image can be improved.
High Light
Compensation*
It’s used to suppress strong backlight for clearer images. Select “ON” or “Auto”, and a gray mask will be covered on the
source of the strong light.
*Selected models only
3.3.7 Privacy Mask (For selected models only)
You can cover certain areas on the camera image with privacy masks.
Item
Description
Mosaic Size
Choose the mosaic size of the privacy mask when “Mosaic” is set to “ON”.
The options are: 8×8, 32×32, and 64×64.
Privacy Mask Name
Name your privacy mask.
Function
Select “On” to enable the privacy mask function.
Mosaic
Select “ON” to have the mosaic effect.
Color
Select “ON” to color the privacy mask.
Mask Color
Select the color for the privacy mask.
Transparency
Select the transparency for your privacy mask.
The options are: 0%, 25%, 50%, and 100%.
Line Width
Choose the line width from 0, 2, 4 and 6 when the transparency is not set to 0%.
20
3.4 VA (For selected models only)
3.4.1 TA
TA, tampering alarm, should be used with the mini-guard control switch for alarm system integration. For more
details, please check with your distributor or installer.
3.5 EVENT
3.5.1 Event
This function is used to integrate the functions of event and alarm detection when this camera has to work with
other ONVIF-compliant device.
3.5 Record
3.5.1 Record
 Enable or disable the alarm record function. When “Enable” is set to “No”, the alarm record function is
disabled even if you enable it in other configuration pages.
 Select if the data should be overwritten when the memory storage is full.
 Enable or disable the audio record function.
 Select the video resolution for event recording.
Note: The higher resolution you choose, the more accuracy and higher image quality the recording will
be, but the faster the memory storage is consumed and become full
21
3.5.2 Record Timer
To schedule alarm and motion recording, enable it, and select the day and time for recording.
Note: The timer must be enabled for the record function to work properly.
Note: The selected time will be yellow-colored.
3.6 Storage
3.6.1 Memory
In “Memory”, you can check the remaining capacity for recording, or clear all recorded data saved if needed.
Note: The recorded data will be removed also when you reset or reboot this camera.
Note: To save more recorded data, it’s recommended to use this camera with the compatible NVR.
Note: To know the total recording time per recording resolution, please refer to “APPENDIX 6
RECORDING TIME TABLE” at page 39.
3.7 Trigger
3.7.1 Trigger
You can configure how this camera reacts when there’s an alarm or motion event.
22

Detect
Item
Description
External Alarm
Enable or disable detection from external alarm-in device, and click the title “External Alarm” (in blue) to set “N.O.”
or “N.C.” depending on the configuration of your alarm-in device.
Motion
Enable or disable motion detection.
Motion detection is not supported when the stream format is Motion JPEG.
When “Enable” is selected, click “Detection” to enter the motion detection area setting page as follows:
Sensitivity:
Set the detection sensitivity from the drop-down list: High, Normal or Low.
Area Setting:
Set the motion detection area by selecting the area grids with your mouse. Pink grids represent the area that is not being
detected while the transparent grids are the area under detection. You can set multiple areas under detection.
Click “Clear All” to set the whole area undetected.
Click “Select All” to set the whole area under detection.
Duration

Set the duration time for trigger recording (5 / 10 / 20 / 40 seconds).
Action
Here defines how the camera delivers alerts to you for any event.
Item
Description
E-Mail
Select the event type you want to receive E-mail notifications when it occurs.
Then, click the title “E-Mail” (in blue) to configure the media type (H264 / JPEG / MPEG4), file format (AVC / AVI),
and record time (1 ~ 5 seconds) for the event video clip.
The camera will send the captured video clip to the E-mail address(s) you assigned in “Network”  “Mail” once the
selected event type occurs.
FTP
Select the event type you want to receive FTP notifications when it occurs.
Then, click the title “FTP” (in blue) to configure the media type (H264 / JPEG / MPEG4), file format (AVC / AVI), and
record time (1 ~ 5 seconds) for the event video clip.
The camera will upload the captured video clip to the FTP site you assigned in “Network”  “FTP” once the
selected event type occurs.
SMS
Select the event type you want to receive a text message when it occurs.
The camera will send a text message to the mobile phone number you assigned in “Network”  “SMS” once the
selected event type occurs.
Alarm Out
Select the event type you want to trigger the alarm-out device to work when it occurs.
Then, click the title “Alarm Out” (in blue) to configure the trigger rule (LOW / HIGH).
*Day and Night is for selected models only.
Record
Select the event type you want to enable event recording when it occurs.
Audio Alert
Select the event type you want to enable audio alert when it occurs.
23
3.7.2 Snapshot
Enable this function to schedule the camera to take snapshots periodically or at a specific time, and send the
snapshots to E-Mail, FTP, and / or Network Share for backup.
Note: Before using E-Mail, FTP and Network Share, make sure the related configurations are done in
“Network”  “Mail”, “Network”  “FTP”, and “Network”  “Network Share”.
Time-lapse Recording
This function allows users to create time-lapse recording by combining snapshots together.
Note: To use this function, make sure “Network Share” is configured well in “Network”  “Network
Share”. For details, please go to “3.2.13 Network Share” at page 17.
Step1: Configure when to take snapshots in “Snapshot”, and choose “Network Share” as the storage mode.
Step2: In “JPG to AVI Conversion”, choose how many images you want to see per second in “FPS”, name the
video file, and specify the file size.
Step3: Click “Convert” to start file conversion, and go to the path specified to store snapshots in “Network Share”
to check the video file.
3.8 General
3.8.1 General
To change the language of UI interface, select from the drop-down list in “Language”.
To lock camera access when it’s not used after the specified time, select “5 MIN”, “15 MIN” or “30 MIN” from the
drop-down list of “Auto Lock Time”, or select “NEVER” to disable this function.
Note: When the camera access is locked after the specified time, to resume camera access, please
enter the password.
24
3.8.2 Time
Set daylight saving time and the current time, and click “Save” to confirm.
Function

Description
Time Configuration
Date
Set the current date.
Time
Set the current time.

Daylight Saving Time Configuration
Daylight Saving Time
Specify whether to use daylight saving time (Enable / Disable).
If this function is enabled, set the time period (Start Time / End Time), and adjust the daylight
saving time in hours (Adjust Time).
3.8.3 Server Log
To quickly search the system logs you want by event type, click “Prev. Page” or “Next Page” to find the logs you
want, or check the event type(s) and click “Reload” to start searching.
To clear all system event logs, click “Clear All”.
25
3.8.4 Online
You can check the current online user(s) with respective online information. To refresh the list, click “Reload”.
 To allow anonymous login, select “Enable” in “Anonymous Viewer Login”.
 To disable image code verification at login, select “No” in “Login with CAPTCHA Image”.
3.8.5 Account
You can create a new account with different user access privilege, or delete or modify an existing account
setting.
How to create a new account
Step1: Click “New”, and fill in the following columns.
Column
Description
User Name
Set a user name that will be used for camera access. The user name allows up to 16 alphanumeric characters.
Password
Set the password that will be used for remote login. The password allows up to 16 alphanumeric characters.
Confirm Password
Enter the password again to confirm.
User Level
Set the security level of an account to give the permission to control different functions. There are four user levels:
SUPERVISOR, POWER USER, NORMAL USER and GUEST.
Life Time
Select how long this account is allowed to stay online (1 MIN / 5 MIN / 10 MIN / 1 HOUR / 1 DAY / INFINITE)
Step2: Then, click “Save” to save your setting and create a new account.
How to modify or delete an existing account
Step1: Select the account you want to modify or delete.
Step2: To modify the account, click “Edit” to change the settings, and click “Save”.
To remove the account, click “Delete”.
Note: It’s not allowed to remove an account when there’s only one account in the account list.
26
3.8.6 Google Maps
This function is used to let you know where the network camera is.
The system will prompt you to apply a Google Maps Key if your access is denied. Please follow the instructions
below when you’re denied:
Step1: Click “Sign up for a Google Maps key” to enter the application page.
Step2: Check the terms and conditions, and enter the IP address of the network camera. Then, click “Generate
API Key”.
Step3: Copy the generated API key, and click “Update Google Maps Key” on the web browser to paste it.
3.8.7 Maintenance
Firmware Upgrade
This function is used when users need to upgrade the camera for function scalability.
Note: Before using this function, make sure you have the correct upgrade files provided by your
installer or distributor.
Note: The event videos saved in the camera will be removed after firmware upgrade. Make sure you’ve
copied important events to your PC before firmware upgrade.
Step1: Select “ ” to browse to where you save the upgrade files, and select them one by one until all files are
selected (up to four files).
27
Step2: Select “Upgrade” to start system upgrading.
Note: You’ll be prompted to keep current configurations. It’s recommended to keep them, or all
configurations will be restored to default values after upgrade.
Note: It takes a few minutes to finish the upgrade process. Do not disconnect the power during
firmware upgrade, or the upgrade may be failed. The camera will reboot after the upgrade.
System Configuration Backup
This function is used to copy your system configuration to a “System.bin” file.
You may import the same system configuration to another camera, or restore your system configuration when
the camera is reset to default values.
Select “System.bin” in “Firmware Upgrade”, and select “Upgrade” to import the system configuration.
System Reboot
Select “Reboot” to restart your camera if needed.
Player Download
To see the event video clips downloaded to your PC, you need to first install our own video player in your PC.
Select “Free Download” to download the video player, and double click the file to install it.
28
APPENDIX 1 PRODUCT SPECIFICATIONS
3MP
Model 1
Model 2
▓ Network
LAN Port
YES
LAN Speed
Supported Protocols
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4, Bonjour, UPnP,
DNS,UDP,IGMP, QoS, SNMP
ONVIF Compatible
YES (Profile S)
Numbers of Online Users
10
Security
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
Remote Access
(1) Internet Explorer on Windows operating system
(2) 24CH Video Viewer on Windows operating system
(3) EagleEyes on iOS & Android mobile devices
▓ Video
Video Compression
H.264 (Main Profile) / MJPEG
Resolution
2048x1536 / 1920 x 1080 / 1280 x 720 / 640 x 480 / 320 x 240
Frame Rate
30fps
Multiple Video Streaming
4 (H.264, MJPEG)
▓ General
Image Sensor
Min Illumination
1/3" CMOS image sensor
1/2.8” CMOS image sensor
0.1 Lux / F1.8;0 Lux (IR LED ON)
0.1 Lux / F1.4(Wide)~F2.8(Tele), 0 Lux (IR LED ON)
Electronic Shutter
1/10,000 ~ 1/7.5 (Slow shutter)
S/N Ratio
More than 48dB (AGC off)
Lens
Viewing Angle
f3.6mm / F1.8
f2.8 ~ 12mm / F1.4 ~ F2.8
67° (Horizontal) / 49° (Vertical) / 87° (Diagonal)
Wide: 94° (Horizontal) / 69° (Vertical) / 120° (Diagonal)
Tele: 29° (Horizontal) / 22° (Vertical) / 36° (Diagonal)
IR LED
36 Units
IR Effective Range
Up to 30 meters
IR Shift
YES
Smart Light Control
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
WDR
DWDR
Micro SD Card Slot
YES (up to 64GB)
POE (Power-over-Ethernet)
YES (IEEE 802.3af)
External Alarm I/O
YES (1 input / 1 output)
RAM
20MB
IP Rating
IP66
Operating Temperature
-25℃ ~ 50℃
Operating Humidity
Less than 60% relative humidity
Power Source (±10%)
DC12V / 1A
Current consumption (±10%)
360mA (IR OFF) / 610mA (IR ON)
708mA Max.
Power Consumption (±10%)
PoE & PoN: 9.5W; DC Adapter: 8.5W
PoE & PoN: 10W; DC Adapter: 8.5W
1.145
1.0
Net Weight(kg)
▓ Audio
Line in
YES (Mono)
Line out
YES (Mono)
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
Minimum Web Browsing Requirements
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 10, Windows 8, Windows 7, Windows Vista & Windows XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later (Windows Edge not supported)
* The specifications are subject to change without notice. ** Dimensional tolerance: ± 5mm
29
2MP
Model 3
Model 4
▓ Network
LAN Port
YES
LAN Speed
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP,
Supported Protocols
RTCP,IPv4, Bonjour, UPnP, DNS,UDP,IGMP, QoS, SNMP
ONVIF Compatible
YES (Profile S)
Numbers of Online Users
10
(1) Multiple user access levels with password
Security
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
Remote Access
(2) 24CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iOS & Android mobile devices
▓ Video
Video Compression
H.264 (Main Profile) / MJPEG
Resolution
1920 x 1080 / 1280 x 720 / 720 x 480 / 352 x 240
Frame Rate
30
Multiple Video Streaming
4 (H.264, MJPEG)
▓ General
Image Sensor
1/2.9” CMOS image sensor
Min Illumination
0.1 Lux / F1.4(Wide)~F2.8(Tele), 0 Lux (IR LED ON)
Electronic Shutter
1/10,000 ~ 1/7.5 (Slow shutter)
S/N Ratio
More than 48dB (AGC off)
Lens
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 103° (Horizontal) / 54° (Vertical) / 122° (Diagonal)
Viewing Angle
Tele: 31° (Horizontal) / 17° (Vertical) / 36° (Diagonal)
IR LED
IR Effective Range
36 Units
4 Units
Up to 30 meters
Up to 40 meters
IR Shift
YES
Smart Light Control
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
WDR
DWDR
POE (Power-over-Ethernet)
YES (IEEE 802.3af)
External Alarm I/O
YES (1 input / 1 output)
RAM
20MB
Micro SD Card Slot
YES (up to 64GB)
IP Rating
IP66
Operating Temperature
-25℃ ~ 50℃
Operating Humidity
Less than 60% relative humidity
Power Source (±10%)
DC12V / 1A
Current consumption (±10%)
667mA
260mA (IR LED OFF); 580mA (IR LED ON)
Power Consumption (±10%)
9.5W (PoE) ; 9.5W (PoN) ; 8W (DC Adapter)
8.7W (PoE) ; 8.7W (PoN) ; 6.96W (DC Adapter)
Net Weight (kg)
1,0
▓ Audio
Line in
YES (Mono)
Line out
YES (Mono)
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
Minimum Web Browsing Requirements
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 10, Windows 8, Windows 7, Windows Vista & Windows XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later (Windows Edge not supported)
* The specifications are subject to change without notice. ** Dimensional tolerance: ± 5mm
30
Model 5
Model 6
▓ Network
LAN Port
YES
LAN Speed
Supported Protocols
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4, Bonjour, UPnP,
DNS,UDP,IGMP, QoS, SNMP
ONVIF Compatible
YES (Profile S)
Number of Online Users
10
(1) Multiple user access levels with password
Security
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
Remote Access
(2) 24CH CMS Lite on Windows operating system
(3) EagleEyes on iOS & Android mobile devices
▓ Video
Network Compression
H.264 (Main Profile) / MJPEG
Video Resolution
1920 x 1080 / 1280 x 720 / 720 x 480 / 352 x 240
Frame Rate
30fps
Multiple Video Streaming
4 (H.264, MJPEG)
▓ General
Image Sensor
Min Illumination
1/2.9” CMOS image sensor
0.1 Lux / F1.5;0 Lux (IR LED ON)
Shutter Speed
S/N Ratio
Lens
Viewing Angle
IR LED
IR Effective Range
0.1 Lux / F1.4(Wide)~F2.8(Tele), 0 Lux (IR LED ON)
1/10,000 ~ 1/7.5 (Slow shutter)
More than 48dB (AGC off)
F3.8mm / F1.5
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 103° (Horizontal) / 54° (Vertical) / 122° (Diagonal)
Tele: 31° (Horizontal) / 17° (Vertical) / 36° (Diagonal)
Wide: 73.2° (Horizontal) / 42.8° (Vertical) / 83.2° (Diagonal)
36 Units
2 Units
Up to 20 meters
Up to 20 meters (Default)/ Up to 35 meters (IE Enhanced)
IR Shift
YES
Smart Light Control
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
Sharpness
Yes
WDR
DWDR
POE (Power-over-Ethernet)
YES (IEEE 802.3af)
Privacy Mask
YES
External Alarm I/O
YES (1 input / 1 output)
RAM
20MB
Micro SD Card Slot
NO
IP Rating
IP67
YES (up to 64GB)
IP66
Operating Temperature
-25℃ ~ 50℃
Operating Humidity
Less than 60% relative humidity
Power Source (±10%)
12V / 1A
Current consumption (±10%)
287mA (IR LED OFF); 632mA (LR LED ON )
301.4mA (IR LED OFF); 484mA (LR LED ON )
Power Consumption (±10%)
9.47W (PoE) ; 9.47W (PoN) ; 7.58W (DC Adapter)
7.26 (PoE) ; 7.26W (PoN) ; 5.81W (DC Adapter)
Net Weight (kg)
0.75
▓ Audio
Line in
YES (Mono)
Line out
YES (Mono)
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
Minimum Web Browsing Requirements
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 10, Windows 8, Windows 7, Windows Vista & Windows XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later (Windows Edge not supported)
31
Model 7
▓ Network
LAN Port
YES
LAN Speed
Supported Protocols
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4, Bonjour, UPnP,
DNS,UDP,IGMP, QoS, SNMP
ONVIF Compatible
YES (Profile S)
Number of Online Users
10
(1) Multiple user access levels with password
Security
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
Remote Access
(2) 24CH CMS Lite on Windows operating system
(3) EagleEyes on iOS & Android mobile devices
▓ Video
Network Compression
H.264 (Main Profile) / MJPEG
Video Resolution
1920 x 1080 / 1280 x 720 / 720 x 480 / 352 x 240
Frame Rate
30/25fps
Multiple Video Streaming
4 (H.264, MJPEG)
▓ General
Image Sensor
1/2.7” CMOS image sensor
Min Illumination
0.1 Lux / F1.5;0 Lux (IR LED ON)
Shutter Speed
1/2 to 1/10000 sec
S/N Ratio
More than 48dB (AGC off)
Lens
F3.8mm / F1.5
Viewing Angle
Wide: 77° (Horizontal) / 45° (Vertical) / 88° (Diagonal)
IR LED
12 Units
IR Effective Distance**
Up to 10 meters
IR Shift
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
Sharpness
Yes
WDR
DWDR
POE (Power-over-Ethernet)
YES (IEEE 802.3af)
External Alarm I/O
YES (1 input / 1 output)
RAM
20MB
Weather-proof
IP66
Operating Temperature
-25℃ ~ 50℃
Operating Humidity
Less than 60% relative humidity
Power Source (±10%)
12V / 1A
Current consumption (±10%)
235mA (IR LED OFF); 360mA (LR LED ON )
Power Consumption (±10%)
5.4W (PoE & PoN) ; 4.32W (DC Adapter)
Net Weight (kg)
0.25
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Motion Detection
YES
Event Notification
FTP / Email / SMS
3-Axis
YES
RTC (real-time clock)
YES
Digital Pan / Tilt / Zoom
Minimum Web Browsing Requirements
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 10, Windows 8, Windows 7, Windows Vista & Windows XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later (Windows Edge not supported)
32
APPENDIX 2 BIT RATE TABLE FOR REFERENCE
The data below is for reference only.
The bit rates listed here may vary depending on the resolution, image quality & frame rate you choose, the
complexity of your monitoring area, and how often the moving objects show in your monitoring area.
Testing Environment



Place: Office Entrance
Network translation: H.264
Camera type: Megapixel camera
Static: No one coming in and out
Dynamic: One or two people coming in and out
Resolution
Quality
Frame Rate
(Dynamic) kbps
(Static) kbps
SXGA
Best
FULL
3253
3216
High
2375
2160
Normal
1571
1266
Basic
1465
873
Best
2010
1261
High
1042
1034
Normal
685
572
Basic
457
350
Best
646
366
High
482
350
Normal
302
286
Basic
168
161
1163
1076
High
989
715
Normal
855
534
Basic
719
443
Best
789
571
High
451
447
Normal
349
237
Basic
217
165
Best
269
147
High
182
131
Normal
164
113
Basic
97
71
VGA
QVGA
SXGA
VGA
QVGA
Best
1/4
33
Resolution
Quality
Frame Rate
(Dynamic) kbps
(Static) kbps
SXGA
Best
1/15
581
374
High
405
342
Normal
487
248
Basic
337
141
Best
358
79
High
201
63
Normal
180
28
Basic
92
15
Best
111
84
High
99
68
Normal
97
54
Basic
58
42
VGA
QVGA
34
APPENDIX 3 POE CONNECTION
This device supports PoE (Power-over-Ethernet), developed by the IEEE802.3af or IEEE802.3at task force, and
power can be supplied over the same network (Ethernet) cable as the one used to connect to Internet. No power
cable is needed. Below shows two examples of POE application for reference.

When your router / hub supports POE connection

When your router / hub doesn’t support POE connection (An optional POE connected required)
35
APPENDIX 4 API ID APPLICATION FOR SMS MESSAGING
To allow the camera automatically sending a text message when an event happens, you need to
apply an API ID from a mobile messaging company first, such as Clickatell or EVERY8D.
Below shows an example of how to get an API ID from Clickatell.
Note: The SMS messaging may not be totally free. Please check the charge policy of the
messaging service you use.
Note: The instructions below are for reference only and may vary when Clickatell’s
official website is updated.
Please follow the steps below for application.
Step1: Go to http://www.clickatell.com/login.php. Sign up an account first.
Step2: Select “Developers Central”, select the location where you want to use this service, and fill in
your information to create an account.
Step3: When the account is created, the system will automatically send an Email to your specified
Email address with the user name, password, and client ID used to log into the service.
Step4: Click the link within the email to log in, and you will be prompted to validate your mobile phone
number. Select “SEND ACTIVATION CODE”. The system will send an activation code to that
number for verification.
Check if you receive a text message from Clickatell, and enter the activation code.
36
Step4: In your account, find “Connection Status” and create a connection (API ID).
Step5: Select “HTTP/S”.
Give a meaning name for this connection, and click “Submit and Get API ID”.
Step5: An API ID will be generated as follows.
Note: Note down the API ID for SMS notification setting later.
37
APPENDIX 5 Q&A
For more details about Q&A, please visit our official website: www.eagleeyescctv.com
Question
Answer
I can connect to this camera in my
house or office where it’s installed
with wireless network.
You didn’t configure this camera to Internet, but only in LAN.
But when I leave my house or office, I
can’t connect to it from my mobile
phone (with 3G network), or other PC
(connected to Internet). Why?
My live images are not fluent. Why?
Please follow the steps in the advanced network setup guide
downloadable from www.surveillance-download.com/user/m650.swf to
complete network configurations, or it’s recommended for you to check
with your local installer or reseller for this service because it’s usually hard
for a person who doesn’t have network knowledge to set network
configurations.
Image fluency could be affected by the local network upload bandwidth,
router efficiency, client network download bandwidth, complexity of live
view, and more.
(Recommended) To have the best image fluency, select QVGA; to have
the best image quality, select “SXVGA” based on the model you have; to
have normal image fluency and quality, select “VGA”.
Please try adjusting the power line frequency to “60 Hz” or “50 Hz” for the
camera.
The live video keeps flickering. Why?
For iOS users, access the camera, and select “
” on the top right
corner to enter IPCAM Configuration page. Then, go to “Advance Setup”
 “Camera” to change setting.
For access from Internet Explorer, log into the camera, and select
“Config.”  “Camera”  “Camera”.
38
APPENDIX 6 RECORDING TIME TABLE
Below shows the estimated total recording time for each recording resolution.
The recording time per resolution is the average value collected from the both alarm trigger conditions indicated in
“Testing Environment”, and is for reference only.
The time may vary depending on the resolution, image quality & frame rate you choose, the complexity of your
monitoring area, and how often the moving objects show in your monitoring area.
Testing Environment
 Place: Office
 Monitoring area: 1.5 meters away from the camera
 Alarm trigger conditions:
(1) One person walks by the monitoring area and leaves immediately.
(2) Two persons walk by the monitoring area. One goes away immediately, and the other one stays a while and
goes away.
Recording Resolution Recording time (second) SXGA VGA QVGA 25 115 211 39
APPENDIX 7 PREREQUISITES FOR NETWORK SHARE
“Push Video” is an active notification system, different from traditional FTP & Email notification methods. It’s more
active and stable, but also easier to be affected by your network bandwidth.
A7.1 Check PC IP Address
Note: The instructions below are taking Windows 7 and 8 for an example.
Step1: Go to "Network and Sharing Center”, and select “Change adapter settings”.
Step2: Right-click on “Local Area Connection”, and select “Properties”.
Note: If your local area connection is not enabled, please also enable it.
Step3: In the “Networking” tab, select “Internet Protocol Version 4 (TCP/IPv4)”, and select “Properties”.
Step4: In the “General” tab, note down the IP address in “Use the following IP address”.
A7.2 Create "Administrator" Account
It’s recommended to create a new administrator account on the PC for “Network Share” to use, or user could use the
existing administrator account.
Note: The instructions below are taking Windows 7 and 8 for an example.
Step1: Go to "User Accounts”  “Manage Accounts”, and select “Create a new account”.
40
Step2: Set a user name, and choose “Administrator” for this account. Then, click “Create Account”.
Step3: Set the password, and click “Create Account”.
A7.3 Share Folder
Note: The instructions below are taking Windows 7 and 8 for an example.
Step1: Right-click the folder you want to use to save snapshots for “Network Share”, and choose “Properties”.
Step2: In “Share Properties”, select the tab of “Sharing”, and choose “Share…”.
41
Step3: Choose the account you want to share with, and click “Share” to save.
42
Download PDF
Similar pages