Section 8 Guaranteed Particular Specifications

Section 8
Guaranteed Particular Specifications
8.1 Guaranteed Technical Particulars for Database Server (Intel Based)
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL
Name of Item
No.
Technical Specification and Standards
(May propose equal
or better)
1
Brand
Should be Internationally Reputed.
2
Model No.
To be mentioned by the Tenderer/Supplier.
3
Country of Origin
To be mentioned by the Tenderer/Supplier.
4
CPU
2 x Intel Xeon Processor E5-2650 8C 2.0GHz
5
Cache
20 MB of Cache
6
Chipset
Intel C602J Chipset
7
Memory
8
9
10
128 GB Registered DDR-3 ECC Memory Upgradeable
to 768 GB
Active Memory
Advanced ECC memory protection support, Memory
protection
mirroring
Server should have Minimum of 16 x 2.5" Hot
Drive Bays
Pluggable Hard Disk Drive bays (Min 8 Bays Active)
Server should be configured with 4x300GB SAS 15
Hard Disk Drives
KRPM 2.5” HDD
RAID Controller with 512 MB Battery back cache. The
11
RAID Controller
12
Graphics Controller
Integrated Video Memory 16MB DDR-2 SDRAM
Ethernet Adapter
4 x integrated Gigabit Ethernet 1000BASE-T ports
13
RAID controller should support Raid 0, 1, 5, 10, 50.
(RJ-45)
14
FC HBA
2 x Single Port 8Gb Optical Fibre Channel HBA
15
I/O Expansions
Minimum Six Number of PCIe Slots
16
Power Supply
Dual Redundant Hot Swappable Power Supplies
Hot Swap/Redundant
Server should be configured with Hot Swap Fans
17
Fans
The server should be able to alert impending failures on
18
Failure Alerting
Mechanism
maximum number of components. The components
covered under alerting mechanism should at least
include Processors, memory, voltage regulator modules
(VRMs), power supplies and fans
19
Ease of failure
Server should send an alert notification on the system
identification
front panel for failure of any component like
8-2
SL
No.
Vendor Response
Name of Item
Technical Specification and Standards
(May propose equal
or better)
Processors, voltage regulator modules
(VRMs),memory, power supplies, fans, HDDs, adapters
and system temperature which will allow system
administrator to identify the component failure.
20
21
22
Form Factor
2U
OEM Server Management software with the device
System Software
Operating System
Support
drivers
Microsoft Windows 2008 Server, RedHat Enterprise
Linux, SUSE Linux Enterprise Server 10 and 11,
VMware vSphere 5
23
Operating System
To be mentioned by the Tenderer/Supplier.
24
RDBMS
To be mentioned by the Tenderer/Supplier.
25
Manufacturer’s Warranty
At least 3 years warranty and parts replacement from
OEMi with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8-3
8.2 Guaranteed Technical Particulars for Application Server
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
1
Brand
Should be Internationally Reputed
2
Model No.
To be mentioned by the Tenderer/Supplier.
3
Country of Origin
To be mentioned by the Tenderer/Supplier.
4
CPU
2 x Intel Xeon Processor E5-2650 8C 2.0GHz
5
Cache
20 MB of Cache
6
Chipset
Intel C602J Chipset
7
Memory
8
Active Memory protection
64GB Registered DDR-3 ECC Memory
Upgradeable to 768 GB
Advanced ECC memory protection support,
Memory mirroring
Drive Bays
9
Server should have Minimum of 16 x 2.5" Hot
Pluggable Hard Disk Drive bays (Min 8 Bays
Active)
10
Hard Disk Drives
Server should be configured with 4x300GB SAS 15
KRPM 2.5” HDD
RAID Controller
11
RAID Controller with 512 MB Battery back cache.
The RAID controller should support Raid 0, 1, 5,
10, 50.
12
13
Graphics Controller
Integrated Video Memory 16MB DDR-2 SDRAM
Ethernet Adapter
4 x integrated Gigabit Ethernet 1000BASE-T ports
(RJ-45)
14
I/O Expansions
Minimum Six Number of PCIe Slots
15
Power Supply
Dual Redundant Hot Swappable Power Supplies
16
Hot Swap/Redundant Fans
Server should be configured with Hot Swap Fans
Failure Alerting Mechanism
The server should be able to alert impending
failures on maximum number of components. The
17
components covered under alerting mechanism
should at least include Processors, memory, voltage
regulator modules (VRMs), power supplies and
fans
8-4
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
Ease of failure
Server should send an alert notification on the
identification
system front pannel for failure of any component
like Processors, voltage regulator modules
18
(VRMs),memory, power supplies, fans, HDDs,
adapters and system temperature which will allow
system administrator to identify the component
failure
19
Form Factor
20
System Software
2U
OEM Server Management software with the device
drivers
Microsoft Windows 2008 Server, RedHat
21
Operating System Support
Enterprise Linux, SUSE Linux Enterprise Server 10
and 11, VMware vSphere 5
22
Operating System
Windows 2012 Server Standard Edition with
License and Media
At least 3 years warranty and parts replacement
23
Manufacturer’s Warranty
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8-5
8.3 Guaranteed Technical Particulars for Backup Management Server
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL
No.
Vendor Response
Name of Item
Technical Specification and Standards
(May propose
equall or better)
1
Brand
Should be Internationally Reputed.
2
Model No.
To be mentioned by the Tenderer/Supplier.
3
Country of Origin
To be mentioned by the Tenderer/Supplier.
4
CPU
5
Cache
15 MB of Cache
6
Chipset
Intel C602J Chipset
7
Memory
8
9
10
1 x Intel Xeon Processor E5-2640 6C 2.5GHz 15MB Cache
1333MHz 95W
32 GB Registered DDR-3 ECC Memory Upgradeable to
768 GB
Active Memory
Advanced ECC memory protection support, Memory
protection
mirroring
Drive Bays
Server should have Minimum of 16 x 2.5" Hot Pluggable
Hard Disk Drive bays (Min 8 Bays Active)
Hard Disk Drives
Server should be configured with 3x300GB SAS 15 KRPM
2.5” HDD
RAID Controller with 512 MB Battery back cache. The
11
RAID Controller
12
Graphics Controller
Integrated Video Memory 16MB DDR-2 SDRAM
Ethernet Adapter
Quad-port with TCP/IP Offload Engine (TOE), Wake on
13
RAID controller should support Raid 0, 1, 5, 10, 50.
LAN, Serial over LAN , PXE 2
14
FC HBA
2 x Single Port 8Gb Optical Fibre Channel HBA
15
I/O Expansions
Minimum Six Number of PCIe Slots
16
Power Supply
Dual Redundant Hot Swappable Power Supplies
Hot Swap/Redundant
Server should be configured with Hot Swap Fans
17
Fans
The server should be able to alert impending failures on
18
Failure Alerting
Mechanism
maximum number of components. The components covered
under alerting mechanism should at least include
Processors, memory, voltage regulator modules (VRMs),
power supplies and fans
8-6
SL
No.
Vendor Response
Name of Item
Technical Specification and Standards
(May propose
equall or better)
Server should send an alert notification on the system front
19
Ease of failure
identification
pannel for failure of any component like Processors, voltage
regulator modules (VRMs),memory, power supplies, fans,
HDDs, adapters and system temperature which will allow
system administrator to identify the component failure
20
Form Factor
2U
21
System Software
OEM Server Management software with the device drivers
22
23
24
Operating System
Support
Operating System
Microsoft Windows 2008 Server, RedHat Enterprise Linux,
SUSE Linux Enterprise Server 10 and 11, VMware vSphere
5
Windows 2012 Server Standard Edition with License and
Media
Manufacturer’s
At least 3 years warranty and parts replacement from OEMi
Warranty
with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8-7
For SMS (Rajshahi):
8.4.1 Guaranteed Technical Particulars for External Storage
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
1
Brand
SUN/IBM/EMC
2
Model
To be mentioned by the Tenderer/Supplier.
3
Country of Origin
To be mentioned by the Tenderer/Supplier.
4
Node Type
Rack Mountable with slide rails rack kit.
Array should be configured with Active/Active Dual
5
Architecture
Controllers for redundancy supporting 8Gbps FC and 1Gbps
iSCSI host interface with embedded storage virtualization
capability to attach external vendor neutral disk systems.
6
Rack Mounted
The SAN storage must be rack mounted
It should support all industry leading operating systems
7
OS & Clustering
Support
including Windows NT, 2000, 2003, 2008, AIX, HP-UX,
Solaris, Redhat linux, Open VMS, IBM i OS, Apple Mac OS
X, etc. The list of supported operating systems should be
provided.
The proposed storage device should be scalable to at least 480
Drives supported with same SAS/FC and NL SAS/SATA
8
Disk Scalability
spindle types. The scalability of the drives can be achieved
using virtualization capability to attach vendor neutral external
disk system. Such Virtualization capability should be
inherently architected and configured from the day one.
The storage array should be configured with 3TB Usable
9
Capacity
space after RAID 1+0 using 300 GB 6Gbps SAS/4Gbps FC
Requirements
Drives and 2TB Usable space after RAID5 using 1TB NLSAS
HDD.
The Storage array should support Global Hot Spare (HS)
17
Hot Spare Disks
Disks. A minimum of 1 global hot spare per disk type and per
disk enclosure should be supplied and configured.
The storage should support an intermix of SSD, SAS/FC and
10
Intermix of Disks
NL SAS/SATA disks and 2.5" and 3.5" form factor drives.
8-8
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
It should be configured with at-least 8 numbers of 8Gbps
11
Front End Ports
front end Fiber Channel ports across Dual controllers or an
aggregate host bandwidth of minimum 64Gbps and 4 numbers
of 1Gbps iSCSI interface.
It should be configured with at-least 4 numbers of 6Gbps
12
Back End
SAS/FC backend ports across Dual controllers towards disks
Connectivity
with the ability to ensure no data loss in the event of failure of
any one of the controller.
Dual Controllers with minimum 8GB cache per controller or
13
Storage Controller
16 GB per storage system. Cache should be mirrored across
controller. Upgradeable option up to 32 GB.
14
The Storage array should support Controller based RAID
RAID
Levels: 0, 1, 10/PD, 4/5, 6 and 1+0
It should provision for Redundancy of critical units like
processor, disk drives, controllers, fan, Power supply etc. and
15
No Single point of
failure
non-disruptive online micro-code upgrades in order to ensure
no single point of failure.
It should support hot plugging and hot swapping of critical
components with minimal disruption.
In case of power failure, system should ensure that there is no
16
Cache Data Backup in loss of data and battery backup for cache should be provided.
Power Failure
Also the data should be de-staged to internal flash or disk
drives for higher protection of data.
18
19
Dynamic LUN
Must support on-line dynamic expansion of LUNs
expansion
LUN Support
The storage device should support 2048 LUN's
The Storage System should support Tiering of Data at LUN
20
Tiering
and Sub LUN level for higher performance required out of
SSD drives.
21
Thin Provisioning
22
Host support
The Storage System should be configured Thin Provisioning
for better utilization of unused capacity.
Please Mention
8-9
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
The Storage System should be provided with intuitive Web
23
Management Software Based GUI interface to manage architectural configuration
and embedded graphical performance monitoring.
Multi pathing driver should be provided along with the storage
24
Multi pathing Driver
device for the maximum nos. of supported host connectivity.
Should be configured with point in time snapshots, full
volume copy. Up to 250 such snapshots per volume should be
possible. It should be possible to create the copies in a
different disk array/system using virtualization capability.
25
PiT Snapshots & Full
Copy
- Should support incremental copy capability – where only
changes from the source are copied during a target refresh
- Should support cascaded copy capability – i.e. capability to
create “copies of copies”. Mappings may be incremental or
non-incremental
- Should have the capability to reverse relationships instantly
to enable rapid data recovery.
26
Virtualization
Please mention
Capability
Replication software should be provided for data replication
across metro and global distances for disaster recovery.
27
Replication
Replication software should support synchronous as well as
asynchronous replication having Unlimited license for full
capacity use of Disk Enclosure.
28
Manufacturer’s
At least 3 years warranty and parts replacement from OEMi
Warranty
with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 10
For DRS (Dhaka):
8.4.2 Guaranteed Technical Particulars for Additional Storage Capacity
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
Additional Storage
1.
Capacity for External
Storage as per 8.4.1 in
3TB Usable space after RAID 1+0 using 300 GB
6Gbps SAS/4Gbps FC Drives required in Dhaka
Storage
Section 8 Page 8-10
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 11
8.5 Guaranteed Technical Particulars for Storage Area Network (SAN) Switch
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
Name of Item
Technical Specification and Standards
Vendor Response
(May propose
equal or better)
1
Brand
Should be internationally reputed
2
Model
To be mentioned by the Tenderer/Supplier.
3
Country of Origin
To be mentioned by the Tenderer/Supplier.
4
Country of Manufacturing
To be mentioned by the Tenderer/Supplier.
Form Factor
19 (nineteen) inch rack mountable, please specify rack
5
6
unit
Number of ports
Fourteen (16) 8Gbps SW SFP Transceiver and
upgradeable up to 24 Ports
Port Bandwidth
7
At least 8 (Eight) Gbps auto-sensing Fiber Channel
ports must support the following port types: (E, F and
FL) with SFP/LC optical interfaces.
8
Aggregate Device
The switch should have Non-blocking architecture
Bandwidth
designed to provide up to 384 Gbps aggregate
throughput with a 24-port configuration
9
10
11
12
13
Redundant Components
Please specify if any
Hot Pluggable/ Swappable
Please specify if any
Components
High Availability
Hot code activation, single field replaceable unit etc.
required – please specify
Security Features
Please specify
Manageability
Web Tools required;
Please specify others
Software
14
Please specify the features of all the software in details
– All the software have to be licensed for unlimited
users
15
Peripherals and Accessories
All required peripherals and accessories
16
Other Features
Please mention, if any
17
Manufacturer’s Warranty
At least 3 years warranty and parts replacement from
OEMi with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 12
8.6 Guaranteed Technical Particulars for Multiprotocol Router Switch
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
Name of Item
Technical Specification and Standards
Vendor Response
(May propose
equal or better)
1
Brand
Should be internationally reputed
2
Model No.
To be mentioned by the Tenderer/Supplier.
3
Chassis
To be mentioned by the Tenderer/Supplier.
4
Fibre Channel interface
For FC: E_Port, EX: Port, F_Port, EL Port, M Port, U
Port
For FCIP: VE _Port (virtual E_Port)
5
Optical transceivers
4 X 8Gbps SFP Transceiver and can be upgradable up
to 16 Fibre Ports
6
Copper transceiver
2 X 1GbE SFP Transceiver and can be upgradable up
to 6 Ethernet Ports
7
Fan And Power Supply
Redundant power supply/dual-fan modules
8
Management and
Switch shall have integrated Ethernet and Serial port
communication port
for management & communication.
9
Country of origin
Should be mentioned.
10
Country of Assemble
Should be mentioned
11
Manufacturer’s Warranty
At least 3 years warranty and parts replacement from
OEMi with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 13
8.7 Guaranteed Technical Particulars for Tape Library
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
Name of Item
Technical Specification and Standards
Vendor
Response (May
propose equal or
better)
1
Brand
Should be mentioned
2
Model No.
Should be mentioned
3
Country of origin
Should be mentioned.
4
Chassis
Rack mount with rack kit
5
Tape Device Type
LTO Ultrium 6 Tape Library
6
Interface
FC (8Gbps) Native Interface
7
Network interface
Ethernet(RJ-45)
8
Number of Drive
1 (One)
9
Minimum throughput
At least 160MB/S
10
Cartridges Slots
At least Twenty Four ( 24 )
11
Library Capacity
60 TB native with LTO Ultrium 6 ( without compression )
12
Hot Swap feature
Power Supply should be hot swappable
13
Remote Management
Remote web-based management and SMI-S interface
feature
capable
14
Tape Cartridges
As required
15
Mixed Tape
Must support mix tape drive technology and mix media
such in same library as LTO4, LTO5 & LTO6.
16
Power Supply
Redundant Power Supply
17
Operating system
Should be mentioned.
18
Cartridge
Twenty (20) LTO6 labeled Data cartridges and Two (2)
Cleaning.
19
Manufacturer’s Warranty
At least 3 years warranty and parts replacement from
OEMi with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 14
8.7.1 Guaranteed Technical Particulars for Tape Backup Software
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL NO
Backup Software Specifications
(May propose equal or
better)
1
The Backup Software should support all major releases of MS Windows & Linux on
the available platforms.
2
The Backup Software must support disk based backups.
3
The Backup software must provide Block level backup of the data.
The Backup software must support continuous, snapshot and scheduled backups of
4
5
6
7
the Client systems. The required license must be provided as a part of the solution.
The Backup software must support SAN based backup (LAN free to disk) backups.
The Backup Software must support snapshot backup of applications like MS
Exchange, Lotus Domino, Oracle and DB2 etc.
The Backup Software should support role based access for manageability (i.e
Administrator level, user level)
The Backup software must provide the granularity for file level and Full data set
8
level restoration of data. Additionally for email and database systems, it must
support the respective, email level and database table level recovery.
9
10
The Backup software must have Bare Machine Restore capability. The required
licenses need to propose as a part of the solution.
The Backup software should capable to provide tape integration for long term
retention of the backed up data.
11
Backup software should support open file backup
12
Should support email alerting
13
Backup software should be capable to replicate the backed up data to DR site
14
The solution should give the provision of compression while taking backup
It should enable near zero data loss recovery of Mail, Applications & Database
15
16
17
18
servers without the need for constant replication or synchronization
The software should have a disaster recovery system in place to protect the data in
case of possible disaster
It should provide details of alerts/errors in the user interface along with detailed
error description and possible resolution.
Solution should provide for one single full backup in lifetime. Should provide
forever incremental full backup with single attempt recovery
19
The solution should be able to recover files in minutes instead of hours
20
The backup of data should be continuous and not limited to a certain backup
8 - 15
Vendor Response
SL NO
Backup Software Specifications
(May propose equal or
better)
window
21
22
The solution should be capable of minimizing potential data loss from 24 hours to
near zero
Proposed Backup Solution Should be configured for all proposed Database and
Application Servers at Data Center (DC & DR).
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 16
8.8 Guaranteed Technical Particulars for Desktop PC Specification for Application Users
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
Name of Item
Technical Specification and Standards
1
2
3
Brand
Model
Country of Origin
To be mentioned by the Tenderer/Supplier
To be mentioned by the Tenderer/Supplier
To be mentioned by the Tenderer/Supplier
4
Country of Manufacturer
To be mentioned by the Tenderer/Supplier
5
6
7
8
9
10
Casing
Processor
Clock Speed
Front Side Bus
Level 2 Cache
System BIOS
11
Chipset
12
RAM
13
14
15
16
Memory slot
Graphics
HDD
Expansion Slot
17
I/O Connector
18
Monitor
19
20
21
22
23
24
Key Board
Mouse & PAD
Optical Drive
Network Card
Sound Card & Speaker
Operating System
25
Software
26
27
Certification
Security
Tower
Intel® Core™ i5 or Higher
Min 3.2 GHz or Higher
1333 MHz
6MB SMART Cache or higher
Flash BIOS with respective brand logo, Machine
Serial No must be shown in BIOS Setup.
Intel H67 or higher Express Chipset, Bus speed :
1333 MHz
4GB DDR3 (1333-MHz) SDRAM upgradable up
to 16GB
2 DIMM's
Integrated Intel HD graphics
Min. 500 GB SATA, 7200 RPM
One (1) full-height PCI Express x1 slots on PCA,
One (1) full-height PCI Express x16 slot on PCA
(for graphic cards), Two (2) full-height PCI slots
on PCA
Rear I/O includes (4) USB 3.0 and (2) USB 2.0
ports, serial RS232 port, PS/2 mouse and keyboard
ports, RJ-45 network interface, One (1) DVI-D
video port and VGA video interfaces, and 3.5mm
audio in/out jacks, Front I/O includes (4) USB 2.0
ports, dedicated headphone output, and a
microphone/headphone jack
18.5” W-LED Color Monitor (same Brand and
color of system unit)
USB Standard Keyboard
USB Standard optical Mouse with mouse pad
DVD-RW (Factory Fitted)
Integrated gigabit (10/100/1000) Ethernet
Integrated sound card and speaker.
Genuine Windows 7 Professional with Original
License and recovery CD/Drive
(i) Licensed bangla software preferably Lekhoney
(ii) Licensed Anti Virus Software preferably
Kesperesky/Norton /Semantic
FCC Class B, ISO 9001: 2000
• One lock to secure both cover and
entire system to fixed object:
∗ Padlock loop (in rear for opt padlock)
∗ Security slot (in rear for optional
Kensington® MicroSaver® cable)
• Power-on password
• Administrator password
8 - 17
Vendor Response (May
propose equal or better)
Hard disk password
Boot sequence control
Boot without keyboard and mouse
Serial port I/O control
Individual USB port disablement
Chassis intrusion switch on selected
model(s)
At least 3 years warranty and parts replacement
•
•
•
•
•
•
28
Manufacturer’s Warranty
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 18
8.9 Guaranteed Technical Particulars for Laser Printer
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Sl.
No.
Name of Item
Technical Specification and Standards
1
2
3
Brand
Model
Country of Origin
To be mentioned by the Tenderer/Supplier.
To be mentioned by the Tenderer/Supplier.
To be mentioned by the Tenderer/Supplier.
4
Country of Manufacturing
To be mentioned by the Tenderer/Supplier.
5
6
7
8
9
10
Paper Size
Processor
Speed
First Page Out
Printer Resolution
Toner type
A4 / Letter/ Legal
Min 800 MHz or higher
Min 62 PPM or higher
Less than 9 seconds from Sleep mode
Min 1200X1200 dpi
Printer with a standard capacity cartridges at least 2000
pages coverage (supported by brochure)
11
12
13
14
15
16
Fuser Unit
Special Feature
Duty Cycle
Interface
RAM
Duplex Printing
Instant on fuser technology with ceramic heating
elements.
Save energy with Auto-On/Auto-Off Technology
At least 50000 Pages per month
Hi Speed USB 2.0 Port
Min 128 MB or higher
Automatic Two side Printing capacity (Auto Duplex)
17
Tray
Input : 50 Sheet multipurpose tray-1, 250 sheets input
tray-2;
Vendor Response (May
propose equal or
Out Put: 125-sheet
18
19
Accessories
Certification
Printer Cable, Power Cord, Driver Software CD
ISO-9000
20
21
22
Toner Life, No of Copies
Drum Life, No of Copies
Manufacturer’s Warranty
To be mentioned by the Tenderer/Supplier.
To be mentioned by the Tenderer/Supplier.
At least 3 years warranty and parts replacement from
OEMi with authorization from OEM to the bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 19
8.10.1 Guaranteed Technical Particulars for Online UPS
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Sl No
Item
1
Brand
2
3
4
Model
Country of origin
Country of
manufacture
Capacity
Transfer time
Input Voltage
Input Frequency
Output Voltage
Technology
Output Frequency
Output Waveform
Phase
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Power Factor
Battery Recharging
Battery Type
Efficiency
Noise
Backup Time
SNMP device/
Remote Network
Interface
Warranty
Required specification
Vendor Response (May
propose equal or better)
Any International reputed brand preferably
APC/Socomec/MGE/Riello
To be mentioned by the bidder
North America/ EU / Japan
To be mentioned by the bidder
Min. 10 kVA
0 mili sec
150- 280 V AC
50 Hz ± 5 Hz
220-230-240 Vac selectable
Double Conversion
50/60 Hz selectable
True Sine Wave
Input Three Phase
Output Single Phase
> 0.98
4-6 hr
Maintenance-free sealed lead-acid
up to 98%
< 45 dBA at 1 m
02 hours at full load
Included with software
Full 03 years for UPS and 01 year for
battery replacement and onsite service
warranty for both.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 20
8.10.2 Guaranteed Technical Particulars for Online UPS
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Sl No
Item
1
Brand
2
3
4
Model
Country of origin
Country of
manufacture
Capacity
Transfer time
Input Voltage
Input Frequency
Output Voltage
Technology
Output Frequency
Output Waveform
Phase
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Power Factor
Battery Recharging
Battery Type
Efficiency
Noise
Backup Time
SNMP device/
Remote Network
Interface
Warranty
Required specification
Vendor Response (May
propose equal or better)
Any International reputed brand
preferably APC/Socomec/MGE/Riello
To be mentioned by the bidder
North America/ EU / Japan
To be mentioned by the bidder
Min. 1 kVA
0 mili sec
150- 280 V AC
50 Hz ± 5 Hz
220-230-240 V AC selectable
Double Conversion
50/60 Hz selectable
Sinewave
Input Single Phase
Output Single Phase
> 0.98
4-6 hr
Maintenance-free sealed lead-acid
up to 98%
< 45 dBA at 1 m
01 hours at full load
Included with software
Full 03 years for UPS and 01 year for
battery replacement and onsite service
warranty for both.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 21
8.10.3 Guaranteed Technical Particulars for Offline UPS
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Sl No
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Brand
Model
Country of origin
Country of manufacturer
Capacity
Input Voltage
Output Voltage
Input Frequency
Battery Recharge Time
Battery Maintenance
Back Up Time
Transfer Time
Wave form (Inverter)
AC input Cable
15
16
UPS off mode
Power Strip
17
Protection
18
Features
19
Warranty
Required specification
To be mention by the bidder
To be mention by the bidder
To be mention by the bidder
To be mention by the bidder
Min 1000 VA
160-270 V AC
220 ± 5%
50 ± 5% Hz
Recharge Time 8 Hours To 90% After Full Discharge
Sealed Maintenance Free
15 Minutes at Full Load.
Less than 2 Mili Sec.
: Stepped Wave Synchronize
High quality a/c cable with fuse protected grounded
13A/15A plug.
Battery charging on.
4 to 6 points x 3 Pin (Universal Options, Foreign
made)
Lightning, Transients, Spike, Sag, Surge, Blackout,
Brownout, Flicker, Over Voltage, Under Voltage,
Over Load, Short circuit, Battery Over Charge,
Battery Low (Deep Discharge) & noise (EMI &
RFI) as per international safety practices
i) Relay Control
ii) Built in wide range Automatic Voltage Stabilizer
1 (one) year full warranty (with Battery)
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 22
Vendor
Response (May
propose equal
or better)
8.11 Guaranteed Technical Particulars for Slip Printer
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Sl No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Description
Specification Requirement
Brand Model
Model
Country of Origin
Country of manufacturer
Print method
Print font
Column capacity
Character per inch
Interfaces
Print speed
Paper
Copy capability
Ribbon life
Internationally Reputed brand
To be mentioned by the bidder
To be mentioned by the bidder
To be mentioned by the bidder
9 pin, dot Matrix
7x9 or 9x9
40/42 or 33/35
17.8/16 or 14.5/13.3
RS 232, bidirectional parallel or USB
4.7 lps at 16 cpi, 40 column
Roll paper
one original, one copy
Min. black 3x10000000 characters
Manufacturer’s Warranty
At least 3 years warranty and parts replacement
Vendor Response
(May propose equal
or better)
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 23
8.12.1 Guaranteed Technical Particulars for Close Rack
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL. No.
Name of Item
Technical Specification and Standards
2
Brand
Same Brand as offered Server
3
Model
Please mention
4
Country of Origin
Please mention
5
Country of Assemble
Please mention
6
Height
42U EIA Closed Rack
Capacity
19” X 73” X 1000 mm (minimum) with:
Vendor Response (May
propose equal or better)
i) All door locks
7
ii) Caster wheel
iii) Cage nuts & screws
iv) Extension bars
8
9
10
Rack Monitor
17” 1U Monitor Console with space saving
keyboard with touch pad.
Integrated Keyboard and
Required with sliding functionality
Mouse
Power Distribution Unit
Power Distribution Unit (PDU)
(PDU)
9 way, 2 units to support for each rack
KVM Switch
Rack Mountable Switch that allows users single-
11
point access and control of up to 8 multiple servers
from a single console along with necessary cables
At least 3 years warranty and parts replacement
12
Manufacturer’s Warranty
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 24
8.12.2 Guaranteed Technical Particulars for Close Rack
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response (May
SL. No.
Name of Item
Technical Specification and Standards
propose equal or
better)
2
Brand
Same Brand as offered Server
3
Model
Please mention
4
Country of Origin
Please mention
5
Country of Assemble
Please mention
6
Height
15U Closed Network Cabinet
7
Capacity
19” X 73” X 1000 mm (minimum) with:
iv) All door locks
ii) Caster wheel
iii) Cage nuts & screws
iv) Extension bars
8
Power Distribution Unit
Power Distribution Unit (PDU)
(PDU)
One 7 port UK Standard PDU to support for each
Rack.
9
Manufacturer’s Warranty
At least 3 years warranty and parts replacement
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 25
8.13 Guaranteed Technical Particulars for Load Balancer
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
1
Name of Item
Technical Specification and Standards
Brand
Should be Internationally reputed.
Model
Should be mentioned
Part/Product No.
Should be mentioned
Country of origin
Should be mentioned.
Country of
Should be mentioned.
Assemble
Chassis
1RU appliance
General Features
Network Port: Four 10/100/1000 Ethernet ports
and Performance
Throughput: .5 Gbps
Virtual contexts: 20
SSL throughput: 1 Gbps
SSL TPS: 7500 SSL TPS using 1024-bit keys
Maximum L4 connections per second: 100,000
complete transactions sustained rate
Maximum L7 connections per second: 30,000
complete transactions sustained rate
Concurrent connections: 1 million
Flash memory: 1 GB
Availability
Application switching: The appliance should provide
load-balancing and content-switching functions with
granular traffic control based on customizable Layer
4 through 7 rules with support for both IPv4 and
IPv6 addresses, virtual IP addresses (VIPs) and
server farms.
Predictors: Predictors or load-balancing algorithms
enable the appliance to select the best server to
satisfy a client request.
Server health monitoring: The appliance checks the
health of application servers and server farms
through configuration of health probes.
Security
Data center security: The appliance should protect
the data center and critical applications from
protocol and denial-of-service (DoS) attacks and
encrypts mission-critical content.
Application security: The appliance should provide
8 - 26
Vendor Response
(May propose equal
or better)
SL No.
Name of Item
Technical Specification and Standards
Vendor Response
(May propose equal
or better)
deep protocol inspection capabilities, which enables
IT professionals to comprehensively secure highvalue applications in the data center. It secures
mission-critical applications and protects against
identity theft, data theft, application disruption, and
fraud and defends web-based applications and
transactions against targeted attacks by professional
hackers.
Management
Embedded browser-based GUI and SNMP
Maximum power
345W
Manufacturer’s
Warranty
At least 3 years warranty and parts replacement
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 27
8.14.1 Guaranteed Technical Particulars for Router
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
1
Brand
CISCO
2
Model
3945E-sec/k9 or Higher
3
Part/Product No.
Should be mentioned
4
Country of origin
Should be mentioned.
5
Country of Assemble
Should be mentioned.
6
General Features
The Router should support Data, Voice, video
and Performance
The Router should have total number of onboard
ports(10/100/1000) RJ-45: 04
Should have two 10/100 Routed port from day 1.
SFP-based ports : 02
Service Module Slots: 04
EHWIC Slots: 03
Number of Double-Wide EHWIC slots: 01
Onboard DSP (PVDM) Slots:03
Embedded Hardware-Based Cryptography and
Acceleration (IPSec + SSL).
Performance should be minimum 2900 kpps (64byte packets) and minimum 8500 Mbps (1500-byte
packets)
Number of concurrent sessions (1000s) 345
WAN Circuit Speed (Mbps): 350
Should have on board VPN acceleration mechanism
and VPN features from Day 1
IP private-branch-exchange (PBX) and key-system
features should support for future
Number of USB console port:01
Number of Serial console ports: 01
Number of auxiliary ports: 01
External USB 2.0 Flash Memory slots:02
Compact Flash: 256 MB(Minimum) support up to 8
GB
DRAM: 1 GB (Minimum) support up to 2 GB
7
Protocols:
IPv4, IPv6, Static Routes, Open Shortest Path First
(OSPF), Enhanced IGRP (EIGRP), Border Gateway
8 - 28
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
Protocol (BGP), BGP Router Reflector,
Intermediate System-to-Intermediate System (ISIS), Multicast Internet Group Management Protocol
(IGMPv3) Protocol Independent Multicast sparse
mode (PIM SM), PIM Source Specific Multicast
(SSM), Distance Vector Multicast Routing Protocol
(DVMRP), IPSec, Generic Routing Encapsulation
(GRE), Bi-Directional Forwarding Detection
(BVD), IPv4-to-IPv6 Multicast, MPLS, L2TPv3,
802.1ag, 802.3ah, L2 and L3 VPN
8
Encapsulation:
Ethernet, 802.1q VLAN, Point-to-Point Protocol
(PPP), Multilink Point-to-Point Protocol (MLPPP),
Frame Relay, Multilink Frame Relay (MLFR)
(FR.15 and FR.16), High-Level Data Link Control
(HDLC), Serial (RS-232, RS-449, X.21, V.35, and
EIA-530), Point-to-Point Protocol over Ethernet
(PPPoE), and ATM
9
Traffic
QoS, Class-Based Weighted Fair Queuing
management:
(CBWFQ), Weighted Random Early Detection
(WRED), Hierarchical QoS, Policy-Based Routing
(PBR), Performance Routing, and NBAR.
10
Power Specifications
AC input voltage: 100-240 VAC
AC input frequency: 47-63 Hz
Should have Redundant Power supply from day 1
Maximum Power capacity with AC power supply:
540 Watts
11
Environmental
Temperature: 5906 ft (1800m) maximum altitude :
specifications
32 to 104ºF(0 to 40ºC)
Operating conditions
Temperature: 9843 ft (3000m) maximum altitude:
32 to 104ºF
(0 to 40ºC)
Temperature: 13123 ft (4000m) maximum altitude:
32 to 86ºF
(0 to 30ºC)
12
Regulatory and
Safety:
Compliance:
UL 60950-1
CAN/CSA C22.2 No. 60950-1
8 - 29
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
EN 60950-1
AS/NZS 60950-1
IEC 60950-1
EMC:
47 CFR, Part 15
ICES-003 Class A
EN55022 Class A
CISPR22 Class A
AS/NZS 3548 Class A
VCCI V-3
CNS 13438
EN 300-386
EN 61000 (Immunity)
EN 55024, CISPR 24
EN50082-1
13
Manufacturer’s
Warranty
At least 3 years warranty and parts replacement
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 30
8.14.2 Guaranteed Technical Particulars for Router
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
1
Brand
CISCO
2
Model
2901-sec/k9 or Higher
3
Part/Product No.
Should be mentioned
4
Country of origin
Should be mentioned.
5
Country of Assemble
Should be mentioned.
6
General Features
The Router should support Data, Voice, video
and Performance
The Router should have total number of onboard
ports(10/100/1000) RJ-45: 02
Should have four 10/100/1000 switch port from day
1.
EHWIC Slots: 04
ISM slots: 01
Number of Double-Wide EHWIC slots: 02
Onboard DSP (PVDM) Slots:02
Embedded Hardware-Based Cryptography and
Acceleration (IPSec + SSL).
Performance should be minimum 330 kpps (64-byte
packets) and minimum 3114 Mbps (1500-byte
packets)
Number of concurrent sessions (1000s) 63
WAN Circuit Speed (Mbps): 25
Should have on board VPN acceleration mechanism
and VPN features from Day 1
IP private-branch-exchange (PBX) and key-system
features should support for future
Number of USB console port:01
Number of Serial console ports: 01
Number of auxiliary ports: 01
External USB 2.0 Flash Memory slots:02
Compact Flash: 256 MB(Minimum) support up to
8 GB
DRAM: 512 MB (Minimum) support up to 2 GB
7
Protocols:
IPv4, IPv6, Static Routes, Open Shortest Path First
(OSPF), Enhanced IGRP (EIGRP), Border Gateway
8 - 31
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
Protocol (BGP), BGP Router Reflector,
Intermediate System-to-Intermediate System (ISIS), Multicast Internet Group Management Protocol
(IGMPv3) Protocol Independent Multicast sparse
mode (PIM SM), PIM Source Specific Multicast
(SSM), Distance Vector Multicast Routing Protocol
(DVMRP), IPSec, Generic Routing Encapsulation
(GRE), Bi-Directional Forwarding Detection
(BVD), IPv4-to-IPv6 Multicast, MPLS, L2TPv3,
802.1ag, 802.3ah, L2 and L3 VPN
8
Encapsulation:
Ethernet, 802.1q VLAN, Point-to-Point Protocol
(PPP), Multilink Point-to-Point Protocol (MLPPP),
Frame Relay, Multilink Frame Relay (MLFR)
(FR.15 and FR.16), High-Level Data Link Control
(HDLC), Serial (RS-232, RS-449, X.21, V.35, and
EIA-530), Point-to-Point Protocol over Ethernet
(PPPoE), and ATM
9
Traffic management:
QoS, Class-Based Weighted Fair Queuing
(CBWFQ), Weighted Random Early Detection
(WRED), Hierarchical QoS, Policy-Based Routing
(PBR), Performance Routing, and NBAR.
10
Power Specifications
AC input voltage: 100-240 VAC
AC input frequency: 47-63 Hz
Support Redundant Power supply.
Maximum Power capacity with AC power supply:
540 Watts
11
Environmental
Temperature: 5906 ft (1800m) maximum altitude :
specifications
32 to 104ºF(0 to 40ºC)
Operating conditions
Temperature: 9843 ft (3000m) maximum altitude:
32 to 104ºF
(0 to 40ºC)
Temperature: 13123 ft (4000m) maximum altitude:
32 to 86ºF
(0 to 30ºC)
12
Regulatory and
Safety:
Compliance:
UL 60950-1
CAN/CSA C22.2 No. 60950-1
8 - 32
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
EN 60950-1
AS/NZS 60950-1
IEC 60950-1
EMC:
47 CFR, Part 15
ICES-003 Class A
EN55022 Class A
CISPR22 Class A
AS/NZS 3548 Class A
VCCI V-3
CNS 13438
EN 300-386
EN 61000 (Immunity)
EN 55024, CISPR 24
EN50082-1
13
Manufacturer’s
At least 3 years warranty and parts replacement
Warranty
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 33
8.15.1 Guaranteed Technical Particulars for Firewall
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
Name of Item
Technical Specification and Standards
1
Brand
CISCO
2
Model
ASA5545X-k9 or Higher
3
Part/Product No.
Should be mentioned
4
Country of origin
Should be mentioned.
5
Country of Assemble
Should be mentioned.
6
Form Factor
1 RU, 19-in rack mountable
7
General Features
8
Temperature
The Firewall should be an appliance based firewall
integrated with full-featured, high-performance security
services.
Firewall throughput: 3 Gbps
Real-world firewall throughput: 1.5 Gbps
Maximum firewall connection: 750000
Maximum firewall connection/second: 30000
IPS throughput (supported): 900 Mbps
3DES/AES VPN throughput: 400 Mbps
VLANS: 300
IPsec VPN Peers: 2500
Security Contexts (Included/Maximum): 2/50
High Availability: Active/Active and Active /Standby
Expansion Slot: 1 interface card
Integrated interface: 8 GE copper
Memory: 12 GB
Flash: 8 GB
System Bus: Multibus architecture
The Firewall should support Layer 2 (Transparent)
mode.
Firewall should support static NAT, Policy based NAT
and PAT.
Firewall should be capable of Dynamic routing on
VPN.
Firewall should support client based IPSec VPN
Tunnels.
Support for Remote Authentication Dial-In User
Service (RADIUS) and AAA and Terminal Access
Controller Access Control System Plus (TACACS+)
23 to 104°F (-5 to 40°C)
9
Power (AC Range
100 to 240 VAC and should have redundant power
Line Voltage)
supply from day 1.
Manufacturer’s
At least 3 years warranty and parts replacement from
Warranty
OEMi with authorization from OEM to the bidder.
and Performance
10
Seal & Signature of the Manufacturer
Vendor Response (May
propose equal or better)
Seal & Signature of the Bidder
8 - 34
8.15.2 Guaranteed Technical Particulars for Firewall
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose equal
or better)
1
Brand
CISCO
2
Model
ASA 5510/k9 or Higher
3
Part/Product No.
Should be mentioned
4
Country of origin
Should be mentioned.
5
Country of Assemble
Should be mentioned.
6
Form Factor
Desktop
7
General Features
Firewall throughput: 300 Mbps
and Performance
Maximum firewall connection: 50,000
Maximum firewall connection/second: 9,000
3DES/AES VPN throughput: 170 Mbps
VLANS: 5 (trunking disabled)/ 20 (trunking
enabled)
IPsec VPN Peers: 25
Integrated interface: 5 Fast Ethernet
Memory: 512 MB
Flash: 128 MB
The Firewall should support Layer 2 (Transparent)
mode.
Firewall should support static NAT, Policy based
NAT and PAT.
Firewall should be capable of routing on VPN.
Firewall should support client based IPSec VPN
Tunnels.
Support for Remote Authentication Dial-In User
Service (RADIUS) and AAA and Terminal Access
Controller Access Control System Plus (TACACS+)
8
Temperature
-13 to 158ºF (-25 to 70ºC)
9
Power (AC Range
100 to 240 VAC.
Line Voltage)
10
Manufacturer’s
Warranty
At least 3 years warranty and parts replacement
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 35
8.16.1 Guaranteed Technical Particulars for Server Switch
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
SL No.
Name of Item
Technical Specification and Standards
1
2
3
4
5
6
Brand
Model
Part/Product No.
Country of origin
Country of Assemble
General Features
and Performance
7
Layer-2 Features
8
Layer-3 Features
CISCO
WS-C3750x 24T-S or Higher
Should be mentioned
Should be mentioned.
Should be mentioned.
The switch should have 24 x 10/100/1000 Gigabit
Ethernet ports and capable to support 10 GB in
future.
The Switch should be Stackable and should have
Stacking throughput at least 64 Gbps.
Should have Redundant Power supply from day 1.
Switching Fabric: 160 Gbps
Forwarding Rate: 65.5 Mpps
Memory: Minimum 256 MB
System Flash: Minimum 64 MB
Jumbo Frame: 9000 Byte
Up to 1005 VLANs support.
Should support 4000 VLAN IDs
Support for up to 12,000 MAC addresses, up to
11,000 unicast routes & 1000 IGMP groups and
multicast routes.
IEEE 802.1Q VLAN encapsulation. Up to 1000
VLANs per switch or stack and upto 4000 VLAN IDs
Support for Automatic Negotiation of Trunking
Protocol, to help minimize the configuration & errors.
Centralized VLAN Management. VLANs created on
the Core Switches should be propagated to all the
other switches automatically, thus reducing the
overhead of creating / modifying / deleting VLANs in
all the switches inturn eliminationg the configuration
errors & troubleshooting.
Spanning-tree PortFast and PortFast guard for fast
convergence.
Support for Uplink Fast and BackboneFast
technologies to help ensure quick failover recovery,
enhancing overall network stability and reliability.
802.1d, 802.1s, 802.1w, 802.3ad, 802.3af Power over
Ethernet (PoE)
Spanning-tree root guard to prevent other edge
swicthes becoming the root bridge.
IGMP snooping v1, v2 and v3
Port Aggregation Protocol (PAgP), Link Aggregation
Protocol (LACP)
Support for Detection of Unidirectional Links and to
disable them to avoid problems such as spanning-tree
loops.
Support for Switch port autorecovery (errdisable) to
automatically reenable a link that is disabled because
of a network error.
Basic IP unicast routing protocols (static, RIPv1, and
RIPv2) from day one.
Support for IPv6 unicast routing capability (static,
8 - 36
Vendor
Response (May
propose equal or
better)
SL No.
Name of Item
9
QoS Features
10
Network security
features
11
Management
Technical Specification and Standards
RIP, and OSPF protocols) to forward IPv6 traffic
through configured interfaces.
Support for Advanced IP unicast routing protocols
(OSPF, Interior Gateway Routing Protocol [IGRP],
and Border Gateway Protocol Version 4 [BGPv4])
for load balancing and constructing scalable LANs.
Policy-Based Routing (PBR) in future.
Support for Protocol Independent Multicast (PIM) for
IP Multicast routing, including PIM sparse mode
(PIM-SM), PIM dense mode (PIM-DM), and PIM
sparse-dense mode.
Support for Multicast VLAN registration (MVR) to
continuously send multicast streams in a multicast
VLAN while isolating the streams from subscriber
VLANs for bandwidth and security reasons.
Cross-stack QoS allows QoS to be configured across
the entire stack.
Standard 802.1p CoS and DSCP
Control- and Data-plane QoS ACLs
Eight egress queues per port to enable differentiated
management of up to four traffic types across the
stack.
Weighted tail drop (WTD) to provide congestion
avoidance
Strict priority queuing mechanisms
Up to 64 aggregate or individual policers for per Fast
Ethernet or Gigabit Ethernet port.
Granular Rate Limiting function to guarantee
bandwidth in increments as low as 8 kbps.
IEEE 802.1x to allow dynamic, port-based security,
providing user authentication.
Support for upto One thousand access control entries
(ACEs).
Spanning-Tree Root Guard (STRG) to prevent edge
devices not in the network administrator's control
from becoming Spanning Tree Protocol root nodes.
BPDU Guard feature, to shut down Spanning Tree
Protocol PortFast-enabled interfaces when BPDUs
are received to avoid accidental topology loops.
Port security to secure the access to an access or trunk
port based on MAC address. After a specific
timeframe, the aging feature should remove the MAC
address from the switch to allow another device to
connect to the same port.
DHCP snooping to allow administrators to ensure
consistent mapping of IP to MAC addresses. This can
be used to prevent attacks that attempt to poison the
DHCP binding database, and to rate limit the amount
of DHCP traffic that enters a switch port.
TACACS+ and RADIUS authentication to enable
centralized control of the switch and restrict
unauthorized users from altering the configuration.
Support for SSHv2, Kerberos, and SNMPv3 to
provide network security by encrypting administrator
traffic during Telnet and SNMP sessions.
CLI support to provide a common user interface and
8 - 37
Vendor
Response (May
propose equal or
better)
SL No.
Name of Item
Technical Specification and Standards
Vendor
Response (May
propose equal or
better)
command set with all routers and switches of the
same vendor.
For enhanced traffic management, monitoring, and
analysis, the Embedded Remote Monitoring (RMON)
software agent should support four RMON groups
(history, statistics, alarms, and events). All nine
RMON groups should be supported through a SPAN
port, which permits traffic monitoring of a single
port, a group of ports, or the entire stack from a single
network analyzer or RMON probe.
Layer 2 traceroute ot ease troubleshooting by
identifying the physical path that a packet takes from
source to destination.
Domain Name System (DNS) to provide IP address
resolution with user-defined device names.
Trivial File Transfer Protocol (TFTP) to reduce the
cost of administering software upgrades by
downloading from a centralized location.
Network Timing Protocol (NTP) to provide an
accurate and consistent timestamp to all intranet
switches.
RMON I and II standards
SNMPv1, SNMPv2c, and SNMPv3.
12
Manufacturer’s
Warranty
At least 3 years warranty and parts replacement
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 38
8.16.2 Guaranteed Technical Particulars for Server Switch
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
1
Brand
CISCO
2
Model
WS-C2960 24TC-L or Higher
3
Part/Product No.
Should be mentioned
4
Country of origin
Should be mentioned.
5
Country of Assemble
Should be mentioned.
6
General Features
The switch should have minimum 24 Ethernet 10/100
and Performance
ports & 2 dual-purpose uplink (dual-purpose uplink
port has 1 10/100/1000 Ethernet port,1 SFP-based
Gigabit Ethernet port, 1 port active)
Support for Redundant Power supply
16 Gbps Forwarding bandwidth
32 Gbps Switching bandwidth
Forwarding rate: 6.5 Mpps
Configurable up to 8000 MAC addresses
7
Layer-2 Features
IEEE 802.1Q VLAN encapsulation. Upto 255 VLANs
should be supported. Support for 4000 VLAN IDs.
Support for Automatic Negotiation of Trunking
Protocol, to help minimize the configuration & errors.
Centralized VLAN Management. VLANs created on
the Core Switches should be propagated automatically.
Spanning-tree PortFast and PortFast guard for fast
convergence
UplinkFast & BackboneFast technologies to help
ensure quick failover recovery, enhancing overall
network stability and reliability.
802.1d, 802.1s, 802.1w, 802.3ad
Spanning-tree root guard to prevent other edge
swicthes becoming the root bridge.
IGMP snooping v3, Support for upto 256 IGMP
Groups. IGMP filtering.
Port Aggregation Protocol (PAgP), Link Aggregation
Protocol (LACP)
Support for Detection of Unidirectional Links and to
disable them to avoid problems such as spanning-tree
8 - 39
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
loops.
The Switch should be able to discover the neighboring
device of the same vendor giving the details about the
platform, IP Address, Link connected through etc, thus
helping in troubleshooting connectivity problems.
Per-port broadcast, multicast, and storm control to
prevent faulty end stations from degrading overall
systems performance.
Local Proxy Address Resolution Protocol (ARP) to
work in conjunction with Private VLAN Edge to
minimize broadcasts and maximize available
bandwidth.
Multicast VLAN registration (MVR) to continuously
send multicast streams in a multicast VLAN while
isolating the streams from subscriber VLANs for
bandwidth and security reasons.
8
Network security
IEEE 802.1x to allow dynamic, port-based security,
features
providing user authentication.
Port-based ACLs for Layer 2 interfaces to allow
application of security policies on individual switch
ports.
SSHv2 and SNMPv3 to provide network security by
encrypting administrator traffic during Telnet and
SNMP sessions.
Bidirectional data support on the Switched Port
Analyzer (SPAN) port to allow the intrusion detection
system (IDS) to take action when an intruder is
detected.
TACACS+ and RADIUS authentication enable
centralized control of the switch and restrict
unauthorized users from altering the configuration.
MAC address notification to allow administrators to be
notified of users added to or removed from the
network.
DHCP snooping to allow administrators to ensure
consistent mapping of IP to MAC addresses. This can
be used to prevent attacks that attempt to poison the
8 - 40
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
DHCP binding database, and to rate-limit the amount
of DHCP traffic that enters a switch port.
Up to 512 ACL entries should be supported.
BPDU Guard to shut down Spanning Tree Protocol
PortFast-enabled interfaces when BPDU’s are received
to avoid accidental topology loops.
9
Quality of Service
Standard 802.1p CoS and DSCP
(QoS) & Control
Control- and Data-plane QoS ACLs
Four egress queues per port to enable differentiated
management of up to four traffic types across the
stack.
Weighted tail drop (WTD) to provide congestion
avoidance
Strict priority queuing mechanisms
Rate Limitting function should guarantee bandwidth in
increments as small as 1 Mbps.
Up to 64 aggregate or individual polices should be
available per Fast Ethernet or Gigabit Ethernet port.
10
Management
CLI support to provide a common user interface and
command set with all routers and switches of the same
vendor.
For enhanced traffic management, monitoring, and
analysis, the Embedded Remote Monitoring (RMON)
software agent should support four RMON groups
(history, statistics, alarms, and events). All nine
RMON groups should be supported through a SPAN
port, which permits traffic monitoring of a single port,
a group of ports, or the entire stack from a single
network analyzer or RMON probe.
Layer 2 traceroute ot ease troubleshooting by
identifying the physical path that a packet takes from
source to destination.
Domain Name System (DNS) to provide IP address
resolution with user-defined device names.
Trivial File Transfer Protocol (TFTP) to reduce the
cost of administering software upgrades by
downloading from a centralized location.
8 - 41
Vendor Response
SL No.
Name of Item
Technical Specification and Standards
(May propose
equal or better)
Network Timing Protocol (NTP) to provide an
accurate and consistent timestamp to all intranet
switches.
RMON I and II standards
SNMPv1, SNMPv2c, and SNMPv3.
11
Manufacturer’s
Warranty
At least 3 years warranty and parts replacement
from OEMi with authorization from OEM to the
bidder.
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 42
8.17 Guaranteed Technical Particulars Of Database
(To be filled up and signed by the Manufacturer & Tenderer (a or b as per offer), otherwise the offer
will not be acceptable)
a) Oracle Database:
Sl
No
.
1
Name of Item
Brand
2
Version
3
Description
4
License
5
Media
6
Brochure
7
Installation
8
Support
service
Required specifications
Manufacturer
Particulars Guaranteed
Oracle
ORACLE 11g Database Enterprise Edition for
LINUX (64 bit) or Latest
Oracle 11g Enterprise Edition
(a) Partitioning
(b) Real Application Clusters
(c) Diagnostics Pack
(d) Tuning Pack
(i) Min. 25 users for 2 node DC cluster
(ii) Min. 25 Users for DR
CD/DVD Media Pack
All brochure, instruction manual and
corresponding CDs will be supplied with the
product
The RDMS should be installed, Configured &
commissioned by the supplier
5 Years full Support Service
b) MS SQL Database:
Sl
Name of Item
No.
1
2
Brand
Version
3
License
4
Brochure
5
6
Installation
Support
service
Required specifications
Manufacturer
Particulars
Guaranteed
MS SQL
MS SQL Server 2012 Enterprise Edition or Latest
For Windows 2012 Server with License and
Media
(i) Min. 25 users for 2 node DC cluster
(ii) Min. 25 Users for DR
All brochure, instruction manual and
corresponding CDs will be supplied with the
product
The RDMS should be installed, Configured &
commissioned by the supplier.
5 Years full Support service
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 43
8.18 Particular Specifications Prepayment Electric Energy Meter
8.18.1 Technical Data Schedule For 230 Volt 10(60) A Pre-payment Solid State Energy Meter
(To be filled up and signed by manufacturer and Bidder, otherwise the offer will not be acceptable)
Sl. No.
Description
Unit
1.
2.
3.
4.
5.
6.
7.
8.
Reference Standard
Country of Origin
Manufacturer’s Name & address
Place of Manufacturer
Year of Manufacture & Testing
Model of Meter.
Generation of the offered Meter
Type
-
9.
Installation
10.
11.
12.
13.
14.
15.
16.
17.
Connection
Rated voltage
Maximum voltage
Basic Current
Maximum Current
Frequency
Number of Terminal
Diameter of Terminal; Bore
Volt
Volt
Amp
Amp
Hz
No.
mm
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
No. of Element
Voltage circuit loss at rated voltage
Current circuit loss at rated current
Variation of Power factor
Variation of voltage
Performance Curve
Impulse withstand voltage
Starting current (minimum)
KWh register type
Meter constant
No.
VA & W
VA
28.
Accuracy class
29.
Type of Battery
30.
No. of Digits for Credit Storage
32.
34.
Token Technology
Numeric Token: Non-contact
membrane keypad
KWhr dispensing register
35.
Front Page Indications
BPDB'S Requirement
-
IEC Standard (as per cl. 4.2)
To be mentioned
To be mentioned
To be mentioned
To be mentioned
To be mentioned
-
To be mentioned
Indoor type
KV
mA
Impulse/kW
hr
Class
5 +1
1- phase, 2-wire
230
280
<=10
>=60
50 ± 5% Hz
4
6mm to accommodate 10
mm2 cable
1 (minimum)
To be mentioned
2.5
0.5 lag to 0.8 lead
-30% to +25%;
To be submitted
6
0.4% of basic current
LCD Display
To be mentioned
1.0
Lithium Battery,
if necessary
5+1
To be mentioned
Solid state LCD Display
- Credit Status,
- accept/Reject,
- Low credit warning,
- Consumption Rate,
8 - 44
Vendor Response
(May propose
equal or better)
Sl. No.
Description
36.
Disconnection Facility
37.
Provision for emergency Friendly
Credit
Time
interval
of
re-calibration
(minimum)
Service life (minimum)
Weight of meter
Overall dimensions (height, width,
depth)
Warranty
List of Recommended Spares
Any other facility if any
39.
40.
41.
42.
43.
44.
45.
Unit
BPDB'S Requirement
Vendor Response
(May propose
equal or better)
- Tamper Indication
− On credit expiry,
− Decommissioning state
− Exceeded Power
threshold
− And when Tampered
− Neutral Missing
− Unable to measure
Energy
To be Mentioned
Year
10
Year
Kg
mm
10
To be mentioned
To be mentioned
Years
3 Years
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 45
8.18.2 Technical Data Schedule For 400 Volt 10(100) A Pre-payment Solid State Energy Meter
(To be filled up and signed by manufacturer and Bidder, otherwise the offer will not be acceptable)
Sl. No.
Description
1
Reference Standard
2
3
4
5
6
7
8
Country of Origin
Manufacturer’s Name & address
Place of Manufacturer
Year of Manufacture & Testing
Model of Meter.
Generation of the offered Meter
Type
9
Installation
10
11
12
3
14
15
16
17
Connection
Rated voltage
Maximum voltage
Basic Current
Maximum Current
Frequency
Number of Terminal
Diameter of Terminal; Bore
18
19
20
21
22
24
25
26
27
28
No. of Element
Voltage circuit loss at rated voltage
Current circuit loss at rated current
Variation of Power factor
Variation of voltage
Performance Curve
Impulse withstand voltage
Starting current (minimum)
KWh register type
Meter constant
29
Accuracy class
30
Type of Battery
31
34
35
No. of Digits for Credit
Storage
Token Technology
Numeric Token: Non-contact
membrane keypad
KWhr dispensing register
Front Page Indications
36
Disconnection Facility
32
Unit
BPDB'S Requirement
-
-
IEC standard (as per cl.
4.2)
To be mentioned
To be mentioned
To be mentioned
To be mentioned
To be mentioned
-
To be mentioned
Indoor type
Volt
Volt
Amp
Amp
Hz
No.
mm
No.
VA & W
VA
KV
mA
Impulse/k
Wh
Class
3- phase, 4-wire
400
480
<=10
>=100
50 ± 5% Hz
08
8.5mm to accommodate
25 mm2 cable
3
To be mentioned
2.5
0.5 lag to 0.8 lead
-30% to +25%
To be submitted
6
0.4% of basic current
LCD Display
To be mentioned
1.0
Lithium Battery,
if necessary
5+1
To be mentioned
Solid state LCD Display
- Credit Status,
- accept/Reject,
- Low credit warning,
- Consumption Rate,
- Tamper Indication
− On credit expiry,
− Decommissioning state
− Exceeded Power
threshold
− And when Tampered
− Neutral Missing
8 - 46
Vendor Response
(May propose equal or
better)
Sl. No.
Description
Unit
BPDB'S Requirement
Vendor Response
(May propose equal or
better)
− Unable to measure
Energy
37
39
40
41
42
43
44
45
Provision for emergency
Friendly Credit
Time interval of re-calibration
(minimum)
Service life (minimum)
Weight of meter
Overall dimensions (height,
width, depth)
Warranty
List
of
Recommended
Spares
Any other facility if any
To be Mentioned
Year
10
Year
Kg
mm
10
To be mentioned
To be mentioned
Year
3 Years
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 47
8.19 Guaranteed Technical Particulars for Hand Held Units
(To be filled in manufacturer letterhead pad, otherwise bid will be rejected)
Item
No
Name of Item
1
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
BPDB'S Requirement
2
Manufacturer Name
3
To be mentioned
Country of Origin
To be mentioned
To be mentioned
Transaction capacity
Rechargeable
Battery
Communications
Interface
Operating System
4
To be mentioned
To be mentioned
Manufacturer
Address
Model no.
Type
Vendor Response (May propose
equal or better)
500
8 hours
IEC Standard.
Communications
Port:
Windows
USB
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 48
8.20 Guaranteed Technical Particulars for Service Connection Materials
(To be field up by the manufacturer, otherwise the bid will be rejected)
Service Bale
Sl.
No.
Description
Purchaser’s
Requirement
Vendor Response (May
propose equal or
better)
Compatible for taking off Service drops from LT Lines.
1.
2.
Name & address of the
Manufacturer
Manufacturer’s Code
Shall be mentioned
3.
Applicable Standard
4.
Installation
5.
Type
BS, IEC, VDE or equivalent
international standard
Outdoor and shall be installed
them on low-tension lines in order
to taking off service drops from
them.
PVC Insulated
6.
Thickness of Insulation
1 (one) mm
7.
Size of Bail
6 SWG Copper
8.
Shape
U-shaped
9.
Length of Copper Wire
458 mm
10.
Weight in Kg
Shall be mentioned
Shall be mentioned
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 49
8.20.1 Guaranteed Technical Particulars for Service Connection Materials
(To be field up by the manufacturer, otherwise the bid will be rejected)
Compression type Connector
Sl.
Description
No.
Vendor Response (May
propose equal or
better)
Purchaser’s
Requirement
Compatible for ACSR MERLIN to ACSR MERLIN Conductor
1.
Name & Address of the
Shall be mentioned
Manufacturer
2.
Manufacturer’s Code No.
Shall be mentioned
3.
Applicable Standard
4.
Installation
5.
6.
7.
Type
Material
Continuous current rating
8.
9.
10.
Length
Weight of 100 nos. in Kg
Dimensional Drawing
BS, IEC, BDS or equivalent
standard
Outdoor and shall be installed for
the above-mentioned conductor.
H-Type
Aluminum
Shall be mentioned and capable of
carrying the continuous current of
the specified conductor in Amps.
112 mm
Shall be mentioned
Shall be enclosed
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
Technical Particulars & Guaranteed Data Schedule of Shackle Insulator
(To be filled up by the Manufacturer, otherwise the bid will not be considered for Evaluation.)
Item
No.
1
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
Description
2
Name of Manufacturer & Address
Manufacturer’s Code No.
Type
Line Voltage
Material
Leakage Distance, min
Flash over Voltage
Power Frequency, Dry
Power Frequency, Wet
Power Frequency Puncture Voltage
Transverse Strength, min
Height, max
Dia, max
Groove Dia.
Insulator Hole Dia., min
Specified Data
Vendor Response (May
propose equal or
better)
3
To be mentioned
To be mentioned
LV Shackle
230/400 V
Glazed Porcelain
64 mm
25 kV
12 kV
70 kV
1140 Kg
76 mm
89 mm
19 mm
17.5 mm
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 50
4
(Guaranteed Technical Particulars)
(To be filled up by the Manufacturer, otherwise the bid will not be considered for Evaluation.)
Insulated Piercing Connector
Item
No.
Description
Purchaser's Requirement
Vendor Response
(May propose
equal or better)
Compatible for House Service Tap-off from 35-70 mm2 Run Conductor
01.
Name of Manufacturer & Address
Shall be mentioned
02.
Manufacturer’s Code No.
Shall be mentioned
03.
Applicable Standard
04.
Installation
05.
Material
06.
Dimension
BS, IEC, BD or equivalent
international standard
Outdoor and Shall be
installed for Al and/or Cu
Conductor
Plated hardened copper alloy
with PVC Insulation
Shall be mentioned
07.
Current carrying Capacity
Shall be mentioned
08.
Weight in Gram
Shall be mentioned
09.
Dimensional Drawing
Shall be Enclosed
Seal & Signature of the Manufacturer
Seal & Signature of the Bidder
8 - 51
Download PDF
Similar pages