Product Manual
Momentus 5400.2 SATA
®
ST9120821SB
ST9100824SB
ST98823SB
ST96812SB
ST94813SB
100392442
Rev. B
August 2007
©2004-2007, Seagate Technology LLC All rights reserved.
Publication number: 100392442, Rev. B
August 2007
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate
Technology LLC in the United States and/or other countries. Momentus, SeagateSeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/
or other countries. All other trademarks or registered trademarks are the property of their
respective owners.
One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion
bytes when referring to hard drive capacity. Accessible capacity may vary depending on
operating environment and formatting. Quantitative usage examples for various applications
are for illustrative purposes. Actual quantities will vary based on various factors, including file
size, file format, features and application software. Seagate reserves the right to change,
without notice, product offerings or specifications.
Contents
1.0
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1
About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1
Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2.1
LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4
Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.5
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.6
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.7
Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.8
Time to ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.9
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9.1
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9.2
Deferred spinup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.9.3
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.9.4
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.1
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.2
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.3
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.4
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.5
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.10.6
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.11
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.12
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.13
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14.1
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14.2
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14.3
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.15
Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.15.1
European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 15
2.16
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.0
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
18
18
19
4.0
Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3
S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
21
23
26
29
30
5.0
Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
i
ii
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Momentus 5400.2 SATA disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
iii
1.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate
Momentus® 5400.2 SATA Blade Server model drives:
• ST9120821SB
• ST9100824SB
• ST98823SB
• ST96812SB
• ST94813SB
These drives provide the following key features:
• 5,400 RPM spindle speed.
• 8 Mbyte buffer.
• High instantaneous (burst) data-transfer rates (up to 150 Mbytes per second).
• Tunneling Magnetoresistive (TMR) recording heads.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Full-track multiple-sector transfer capability without local processor intervention.
• Quiet operation.
• 800 Gs nonoperating shock and 250 Gs of operating shock.
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• The 3D Defense System™, which includes Drive Defense, Data Defense and Diagnostic Defense, offers the
industry’s most comprehensive protection for disc drives.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Support for Read Multiple and Write Multiple commands.
Figure 1. Momentus 5400.2 SATA disc drive
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
1
1.1
About the Serial ATA interface
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary
advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current
system and expect all of your existing applications to work as normal.
The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0
(master) devices.
Note.
The host adapter may, optionally, emulate a master/slave environment to host software where two
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA
environment.
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide
backward compatibility with existing host systems and software. The Command and Control Block registers,
PIO and DMA data transfers, resets, and interrupts are all emulated.
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized
AT Attachment” specification. The specification can be downloaded from http://www.serialata.org.
2
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
2.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the
ST9120821SB, ST9100824SB, ST98823SB, ST96812SB, ST94813SB and ST93811AS models.
2.1
Specification summary table
The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.
Table 1:
Drive specifications
Drive specification
ST9120821SB ST9100824SB ST98823SB
ST96812SB
ST94813SB
Formatted Gbytes (512 bytes/sector)*
120
100
80
60
40
Guaranteed sectors
234,441,648
195,371,568
156,301,488
117,210,240
78,140,160
Bytes per sector
512
Default sectors per track
63
Default read/write heads
16
Default cylinders
16,383
Physical read/write heads
4
4
3
2
2
Discs
2
2
2
1
1
Recording density in BPI (bits/inch max)
778k
Track density TPI (tracks/inch max)
126k
Areal density
(Mbits/inch2 max)
98.2
Spindle speed (RPM)
5,400
Internal transfer rate (Mbytes/sec max)
42
I/O data transfer rate (Mbytes/sec max)
150
ATA data-transfer modes supported
SATA 1.0, SATA II
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Cache buffer
8 Mbytes
Height (max)
9.5 +/- 0.2 mm (0.374 +/- .0078 inches)
Width (max)
69.85 mm (2.75 +/- 0.0098 inches)
Length (max)
100.5 +/- 1.6 mm (3.96 +/- 0.063 inches)
Weight (typical)
100 grams (0.22 lb)
Average latency (msec)
5.56
Power-on to ready (typical)
3.5 sec
Standby to ready (typical)
3.0 sec
Startup current, (typical, peak)
+5V: 1.1A
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
3
Table 1:
Drive specifications
Drive specification
ST9120821SB ST9100824SB ST98823SB
ST96812SB
Track-to-track seek time
(msec typical)
1.0 (read), 1.5 (write)
Average seek, read (msec typical)
12.5
Average seek, write (msec typical)
14.5
Seek power (typical)
2.20 watts
Read/write power (typical)
Read: 1.90 watts; Write: 2.30 watts
Idle mode, low power (typical)
0.80 watts
Standby mode (typical)
0.28 watts**
Sleep mode (typical)
0.28 watts**
Voltage tolerance (including noise)
+5.0V ± 5%
Ambient temperature
5° to 55°C (operating), –40° to 70°C (nonoperating)
Temperature gradient
(°C per hour max)
20°C (operating)
30°C (nonoperating)
Relative humidity
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature
(°C max)
30 (operating)
40 (nonoperating)
Altitude, operating
–304.8 m to 3,048 m
(–1000 ft to 10,000+ ft)
Altitude, nonoperating
(meters below mean sea level, max)
–304.8 m to 12,192 m
(–1000 ft to 40,000+ ft)
Shock, operating (Gs max at 2 msec)
250
Shock, nonoperating (Gs max at 2 msec)
800
Shock, nonoperating (Gs max at 1 msec)
900
Shock, nonoperating (Gs max at 0.5 msec)
400
Vibration, operating
1.0 G (0 to peak, 5–500 Hz)
Vibration, nonoperating
5 Gs (0 to peak, 5–500 Hz)
ST94813SB
Drive acoustics, sound power (bels)
Idle***
2.4 (typical)
2.6 (max)
Performance seek
2.9 (typical)
3.1 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
1.74% at maximum case temperature of 40°C and 8,760 power on hours (POH).
Service life
5 Years
Warranty
5 years on distribution units.
To determine the warranty for a specific drive, use a web browser to access the
following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
Load/Unload (U/UL) cycles
25°C, 50% relative humidity
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Supports Hotplug operation per SATA II specification Yes (requires COMPRESET from host after a hotplug event)
4
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes
will not contribute to battery power consumption.
***During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
2.2
Formatted capacity
Model
Formatted capacity*
Guaranteed sectors
Bytes per sector
ST9120821SB
120 Gbytes
234,441,648
512
ST9100824SB
100 Gbytes
195,371,568
512
ST98823SB
80 Gbytes
156,301,488
512
ST96812SB
60 Gbytes
117,210,240
512
ST94813SB
40 Gbytes
78,140,160
512
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
2.2.1
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48bit addressing support of drives with capacities over 137 Gbytes.
2.3
Default logical geometry
Cylinders
Read/write heads
Sectors per track
16,383
16
63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
5
2.4
Physical organization
Drive model
Read/write heads
Number of discs
ST9120821SB
4
2
ST9100824SB
4
2
ST98823SB
3
2
ST96812SB
2
1
ST94813SB
2
1
2.5
Recording and interface technology
Interface
Serial ATA (SATA)
Recording method
16/17 EPRML
Recording density BPI (bits/inch max)
778k
Track density TPI (tracks/inch max)
126k
Areal density
(Mbits/inch2
max)
98.2
Spindle speed (RPM) (± 0.2%)
5,400
Maximum Internal transfer rate (Mbytes/sec)
42
I/O data-transfer rate (Mbytes/sec max)
150 (SATA 1.0)
Interleave
1:1
Cache buffer
8 Mbytes (8,192 kbytes)
2.6
Physical characteristics
Drive specification
6
Height
(mm)
(inches)
9.5 +/-0.2
0.374 +/-0.0078
Width
(mm)
(inches)
69.85 +/-0.25
2.75 +/-0.0098
Length
(mm)
(inches)
100.5 +/-1.6
3.945 +/-0.0098
Typical weight
(grams)
(pounds)
100
0.22
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
2.7
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between
random tracks, less overhead.
Table 2:
Typical seek times
Typical seek times (msec)
Read
Write
Track-to-track
1.0
1.5
Average
12.5
14.5
Full-stroke
22.0
24.0
Average latency
5.56
5.56
Note.
2.8
These drives are designed to consistently meet the seek times represented in this manual. Physical
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted
values. However, due to the manner in which these drives are formatted, benchmark tests that
include command overhead or measure logical seeks may produce results that vary from these
specifications.
Time to ready
Time to ready
Typical
Max @ 25°C
Power-on to Ready (sec)
3.5
8.0
Standby to Ready (sec)
3.0
8.0
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
7
2.9
Power specifications
The drive receives DC power (+5V) through a native SATA power connector.
2.9.1
Power consumption
Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on
an average of drives tested, under nominal conditions, at 25°C ambient temperature, after 25 minutes of operation.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on
three random seek operations every 100 msecs. This mode is not typical.
• Read/write power and current
Read/write power is measured with the heads on track, based on three 63 sector read or write operations
every 100 msecs.
• Idle mode power
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in
a random track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down model
Table 3:
DC power
Power dissipation
+5V input average (25° C)
Spinup
1.1 A
Seek
2.20 watts
Read
1.90 watts
Write
2.30 watts
Idle, performance mode*
1.70 watts
Idle, active*
0.99 watts
Idle, low power mode*
0.80 watts
Standby
0.28 watts
Sleep
0.28 watts
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
8
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
Figure 2. Typical +5V only startup and operation current profile
2.9.2
Deferred spinup
Momentus 5400.2 SATA drives provide a deferred spinup feature which storage subsystem controllers can use
to sequence disc drive initialization. This is beneficial to systems which include multiple Serial ATA hard disc
drives because it allows subsystem controllers to stagger the spinup of each drive to accommodate available
power supply current. This feature does not impact time-to-ready in typical desktop systems.
To accommodate the deferred spinup of multiple disc drives in an enclosure, Momentus 5400.2 SATA disc
drives will spin up only after power is applied to the drive and after successful PHY (Physical layer) initialization. PHY initialization occurs after the PHY enters the DP7:DR_Ready state. This state is reached after a successful exchange of Out-Of-Band (OOB) signals with a functional host-side Serial ATA port. In desktop
systems, SATA transceivers should initialize OOB as soon as power comes ready to guarantee the drive spins
up quickly. Seagate disc drives will not spin up without an operational host-side Serial ATA transceiver.
Additional details
Upon system power up, PHY communication is initiated with a COMRESET signal, which is generated by the
host-side transceiver. COMRESET is followed by a COMINIT signal generated by the disc drive transceiver.
COMRESET and COMINIT are followed by an exchange of COMWAKE signals and Align primitives. The disc
drive will spin up after the successful exchange of Align primitives cause the PHY to come ready.
For more details, refer to:
• Section 6.8 of the Serial ATA 1.0 High-Speed Serialized AT Attachment specification
• Section 6.2 of the Serial ATA II: Extensions to Serial ATA 1.0 specification
• SATA 1.0 design guides
Note.
These specifications and guides are available on the Serial ATA web site (www.serialata.org).
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
9
2.9.3
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on
the +5 volt line.
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
Note.
Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write
current.
2.9.4
Voltage tolerance
Voltage tolerance (including noise):
5V ± 5%
2.10
Environmental specifications
2.10.1
Ambient temperature
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions.
Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
Operating:
Nonoperating:
2.10.2
5° to 40°C (41° to 104°F)
–40° to 70°C (–40° to 158°F)
Temperature gradient
Operating
20°C per hour (68°F per hour max), without condensation
Nonoperating
30°C per hour (86°F per hour max), without condensation
2.10.3
Humidity
2.10.3.1
Relative humidity
Operating
5% to 90% noncondensing (30% per hour max)
Nonoperating
5% to 95% noncondensing (30% per hour max)
2.10.3.2
Wet bulb temperature
Operating
30°C (86°F max)
Nonoperating
40°C (104°F max)
2.10.4
Altitude
Operating
–304.8 m to 3,048 m (–1,000 ft to 10,000+ ft)
Nonoperating
–304.8 m to 12,192 m (–1,000 ft to 40,000+ ft)
10
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
2.10.5
Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive
mounting screws. Shock may be applied in the X, Y or Z axis.
2.10.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum
operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more
than two times per second.
2.10.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse
of 2 msec duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 900 Gs based on a nonrepetitive half-sine shock pulse
of 1 msec duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 400 Gs based on a nonrepetitive half-sine shock pulse
of 0.5 msec duration.
2.10.6
Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the
drive mounting screws. Vibration may be applied in the X, Y or Z axis.
2.10.6.1
Operating vibration
The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below.
5–500 Hz
2.10.6.2
1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.
Nonoperating vibration
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below.
5–500 Hz:
5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
11
2.11
Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.
For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the
following equation:
(Number of seeks per second = 0.4 / (average latency + average access time))
Table 4:
Drive level acoustics
Idle*
Performance Seek
2.4 bels (typ)
2.6 bels (max)
2.9 bels (typ)
3.1 bels (max)
Note.
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase
acoustic and power to operational levels.
2.12
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the radio frequency (RF) environments defined in the following table:
Table 5:
Radio frequency environments
Test
Description
Performance level
Reference standard
Electrostatic discharge
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV
B
EN 61000-4-2: 95
Radiated RF immunity
80 to 1,000 MHz, 3 V/m,
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse modulation @
200 Hz
A
EN 61000-4-3: 96
ENV 50204: 95
Electrical fast transient
± 1 kV on AC mains, ± 0.5 kV on external I/ B
O
EN 61000-4-4: 95
Surge immunity
± 1 kV differential, ± 2 kV common, AC
mains
B
EN 61000-4-5: 95
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms, 80% AM with
1 kHz sine
A
EN 61000-4-6: 97
Voltage dips, interrupts
0% open, 5 seconds
0% short, 5 seconds
40%, 0.10 seconds
70%, 0.01 seconds
C
C
C
B
EN 61000-4-11: 94
12
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
2.13
Reliability
Measurement type
Specification
Nonrecoverable read errors
1 per 1014 bits read, max.
Annualized Failure Rate (AFR)
1.74% at maximum case temperature of 40°C and 8,760 power on hours (POH).
Load/Unload (U/UL)
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Service Life
5 years
Warranty
5 years on distribution units.
To determine the warranty for a specific drive, use a web browser to access the
following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
2.14
Agency certification
2.14.1
Safety certification
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections
of IEC950 and EN 60950 as tested by TUV North America.
2.14.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and
the immunity levels are defined by EN 55024.
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators
should confirm EMC compliance and provide CE marking for their products.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
13
Korean RRL
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information
and Communication Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.
• EUT name (model numbers): ST9120821SB, ST9100824SB, ST98823SB, ST96812SB, and ST94813SB.
• Certificate numbers:
ST9120821SB
ST9100824SB
ST98823SB
ST96812SB
ST94813SB
E-D011-05-2395(B)
E-D011-05-2395(B)
E-D011-05-2395(B)
E-D011-05-2395(B)
E-D011-05-2395(B)
• Trade name or applicant: Seagate Technology
• Manufacturing date: June 2005
• Manufacturer/nationality: USA, Singapore and China
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
2.14.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
14
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
2.15
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances.
2.15.1
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical
substances, including Lead (Pb), in electronic products effective July 2006.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the
rep-resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion
of any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard
operat-ing procedures that ensure that restricted substances are not utilized in our manufacturing operations,
labora-tory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
2.16
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
15
16
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
3.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s
exposure to ESD.
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire
installation procedure.
• Handle the drive only by its edges or frame.
• The drive is fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
17
3.2
Configuring the drive
Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point
relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the
two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are
Device 0 (master) devices.
Serial ATA drives are designed for easy installation with no jumpers, terminators, or other settings. It is not necessary to set any jumpers on this drive for proper operation. The jumper block adjacent to the signal connector
is for factory use only.
SATA interface connector
Jumper block
(factory use only)
SATA power connector
Figure 3. Serial ATA connectors
3.3
Serial ATA cables and connectors
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 6
for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive
and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind
mateable.
For installations which require cables, you can connect the drive as illustrated in Figure 4.
SATA interface connector
Power connector
SATA interface cable
Power cable
Figure 4. Attaching SATA cabling
Each cable is keyed to ensure correct orientation.
18
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
3.4
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting
holes. See Figure 5 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
• Use only M3 UNC mounting screws.
• Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).
• Four (4) threads (0.080 inches) minimum screw engagement recommended.
Measurements shown in Figure 5 are in inches.
1
DIMENSIONS PER EIA-720 OR SFF 8201 SPECIFICATION.
2
DIMENSIONS PER SFF 8212 OR SFF 8223.
3
DRIVE LENGTH W/ PATA IS 3.945±.057 (WORST CASE).
DRIVE LENGTH W/ SATA IS 3.957±.062 (WORST CASE).
3.945 ± .010
(BASE)
.157
( .490 )
.217 ±.050
2
.217 ±.050
2 .399
C
( .673 )
OF CONN.
DATUM B
C
OF DRIVE
1 2.750
±.010
(BASE)
( .189 )
2
SATA
PATA
3
BASE
3.567
.551
1
1
2X M3 X 0.5-6H
MOUNTING HOLES; BOTH SIDES
.12 MIN FULL THREAD
0.148 ±.010 X 90
( .020 )
SECTION B-B (SATA)
1
.374 ±.008
-D2X .118
BOTH SIDES
1
B C D
BASE
.039
.551
3.567
(BASE)
1
2 .152
1
4X M3 X 0.5-6H
MOUNTING HOLES; BOTH SIDES
.10 MIN FULL THREAD
0.148 ±.010 X 90
1
.399
2
DETAIL A (PATA)
B
1
.039
.016
2.430
B C D
C
B
-B2 .012
.370
2
DETAIL A
DETAIL A (SATA)
.160
1
-C-
Figure 5. Mounting dimensions—top, side and end view
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
19
20
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
4.0
Serial ATA (SATA) interface
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA
programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive
also supports the use of the IORDY signal to provide reliable high-speed data transfers.
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT
Attachment” specification.
4.1
Hot-Plug compatibility
Momentus 5400.2 SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification
can be downloaded from http://www.serialata.org. This device requires a COMRESET from the host after a
hotplug event.
4.2
Serial ATA device plug connector pin definitions
Table 6 summarizes the signals on the Serial ATA interface and power connectors..
Table 6:
Segment
Signal
Serial ATA connector pin definitions
Pin
Function
Definition
S1
Ground
2nd mate
S2
A+
Differential signal pair A from Phy
S3
A-
S4
Ground
2nd mate
S5
B-
Differential signal pair B from Phy
S6
B+
S7
Ground
2nd mate
Key and spacing separate signal and power segments
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
21
Table 6:
Segment
Power
Serial ATA connector pin definitions
Pin
Function
Definition
P1
V33
3.3V power
P2
V33
3.3V power
P3
V33
3.3V power, pre-charge, 2nd mate
P4
Ground
1st mate
P5
Ground
2nd mate
P6
Ground
2nd mate
P7
V5
5V power, pre-charge, 2nd mate
P8
V5
5V power
P9
V5
5V power
P10
Ground
2nd mate
P11
Reserved
The pin corresponding to P11 in the backplane receptacle connector is also reserved
The corresponding pin to be mated with P11 in the power cable receptacle connector
shall always be grounded
P12
Ground
1st mate.
P13
V12
12V power, pre-charge, 2nd mate
P14
V12
12V power
P15
V12
12V power
Notes:
1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this
case, the mating sequences are:
• the ground pins P4 and P12.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when
installed in a blind-mate backplane configuration.
4. All used voltage pins (Vx) must be terminated.
22
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
4.3
Supported ATA commands
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of
the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See
“S.M.A.R.T. commands” on page 30.for details and subcommands used in the S.M.A.R.T. implementation.
Command name
Command code (in hex)
ATA-standard commands
Device Configuration Restore
B1h/C0h
Device Configuration Freeze Lock
B1h/C1h
Device Configuration Identify
B1h/C2h
Device Configuration Set
B1h/C3h
Download Microcode
92h
Execute Device Diagnostics
90h
Flush Cache
E7h
Flush Cache Extended
EAh
Identify Device
ECh
Initialize Device Parameters
91h
Read Buffer
E4h
Read DMA
C8h
Read DMA Extended
25h
Read DMA without Retries
C9h
Read Long with Retries
22h
Read Long without Retries
23h
Read Multiple
C4h
Read Multiple Extended
29h
Read Native Max Address
F8h
Read Native Max Address Extended
27h
Read Sectors
20h
Read Sectors Extended
24h
Read Sectors without Retries
21h
Read Verify Sectors
40h
Read Verify Sectors Extended
42h
Read Verify Sectors without Retries
41h
Seek
70h
Set Features
EFh
Set Max Address
F9h
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
23
Command name
Command code (in hex)
Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right.
Address:
Password:
Lock:
Unlock:
Freeze Lock:
Set Multiple Mode
C6h
S.M.A.R.T. Disable Operations
B0h/D9h
S.M.A.R.T. Enable/Disable Autosave
B0h/D2h
S.M.A.R.T. Enable Operations
B0h/D8h
S.M.A.R.T. Enable/Disable Auto Offline
B0h/DBh
S.M.A.R.T. Enable One Attribute Modification
B0h/E0h
S.M.A.R.T. Execute Offline
B0h/D4h
S.M.A.R.T. Read Attribute Thresholds
B0h/D1h
S.M.A.R.T. Read Data
B0h/D0h
S.M.A.R.T. Read Log Sector
B0h/D5h
S.M.A.R.T. Return Status
B0h/DAh
S.M.A.R.T. Save Attribute Values
B0h/D3h
S.M.A.R.T. Write Attribute Thresholds
B0h/D7h
S.M.A.R.T. Write Attribute Values
B0h/E1h
S.M.A.R.T. Write Log Sector
B0h/D6h
Write Buffer
E8h
Write DMA
CAh
Write DMA Extended
35h
Write DMA without Retries
CBh
Write Long with Retries
32h
Write Long without Retries
33h
Write Multiple
C5h
Write Sectors
30h, 31h
Write Sectors Extended
34h
00H
01H
02H
03H
04H
ATA-standard power-management commands
Check Power Mode
98h or E5h
Idle
97h or E3h
Idle Immediate
95h or E1h
Sleep
99h or E6h
Standby
96h or E2h
Standby Immediate
94h or E0h
ATA-standard security commands
24
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
Command name
Command code (in hex)
Security Set Password
F1h
Security Unlock
F2h
Security Erase Prepare
F3h
Security Erase Unit
F4h
Security Freeze Lock
F5h
Security Disable Password
F6h
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
25
4.3.1
Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following
power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on
page 27. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or
vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
The following commands contain drive-specific features that may not be included in the Serial ATA specification.
Word
Description
Value
0C5AH
0
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
1
Number of logical cylinders
16,383
2
ATA-reserved
0000H
3
Number of logical heads
16
4
Retired
0000H
5
Retired
0000H
6
Number of logical sectors per logical track: 63
003FH
7–9
Retired
0000H
10–19
Serial number: (20 ASCII characters, 0000H = none)
ASCII
20
Retired
0000H
21
Retired
0400H
22
Obsolete
0000H
23–26
Firmware revision (8 ASCII character string, padded with
blanks to end of string)
x.xx
27–46
Drive model number: (40 ASCII characters, padded with
blanks to end of string)
ST9120821SB
ST9100824SB
ST98823SB
ST96812SB
ST94813SB
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple
and Write multiple (16)
8010H
48
Reserved
0000H
49
Standard Standby timer, IORDY supported and may be disabled
2F00H
50
ATA-reserved
0000H
51
PIO data-transfer cycle timing mode
0200H
52
Retired
0200H
53
Words 54–58, 64–70 and 88 are valid
0007H
54
Number of current logical cylinders
xxxxH
55
Number of current logical heads
xxxxH
26
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
Word
Description
Value
56
Number of current logical sectors per logical track
xxxxH
57–58
Current capacity in sectors
xxxxH
59
Number of sectors transferred during a Read Multiple or
Write Multiple command
xxxxH
60–61
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
ST9120821SB = 234,441,648
ST9100824SB = 195,371,568
ST98823SB = 156,301,488
ST96812SB = 117,210,240
ST94813SB = 78,140,160
62
Retired
0000H
63
Multiword DMA active and modes supported
(see note following this table)
xx07H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003H
65
Minimum multiword DMA transfer cycle time per word
(120 nsec)
0078H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
0078H
67
Minimum PIO cycle time without IORDY flow control
(240 nsec)
00F0H
68
Minimum PIO cycle time with IORDY flow control (120 nsec)
0078H
69–74
ATA-reserved
0000H
75
Queue depth
0000H
76
Serial ATA capabilities
0508H
77
ATA-reserved
0000H
78
Serial ATA features supported
0048H
79
Serial ATA features enabled
0040H
80
Major version number
003EH
81
Minor version number
0000H
82
Command sets supported
306BH
83
Command sets supported
4001H
84
Command sets support extension
4000H
85
Command sets enabled
30xxH
86
Command sets enabled
0001H
87
Command sets enable extension
4000H
88
Ultra DMA support and current mode
(see note following this table)
xx7FH
89
Security erase time
0000H
90
Enhanced security erase time
0000H
92
Master password revision code
FFFEH
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
27
Word
Description
Value
93
Hardware reset value
(see description following this table)
xxxxH
94
Auto acoustic management setting
xxxxH
95–99
ATA-reserved
0000H
100–
103
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
These words are required for drives that support the 48-bit
addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
ST9120821SB = 234,441,648
ST9100824SB = 195,371,568
ST98823SB = 156,301,488
ST96812SB = 117,210,240
ST94813SB = 78,140,160
104–
127
ATA-reserved
0000H
128
Security status
0001H
129–
159
Seagate-reserved
xxxxH
160–
254
ATA-reserved
0000H
255
Integrity word
xxA5H
Note.
See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data:
Description (if bit is set to 1)
28
Bit
Word 63
0
Multiword DMA mode 0 is supported.
1
Multiword DMA mode 1 is supported.
2
Multiword DMA mode 2 is supported.
8
Multiword DMA mode 0 is currently active.
9
Multiword DMA mode 1 is currently active.
10
Multiword DMA mode 2 is currently active.
Bit
Word 88
0
Ultra DMA mode 0 is supported.
1
Ultra DMA mode 1 is supported.
2
Ultra DMA mode 2 is supported.
3
Ultra DMA mode 3 is supported.
4
Ultra DMA mode 4 is supported.
8
Ultra DMA mode 0 is currently active.
9
Ultra DMA mode 1 is currently active.
10
Ultra DMA mode 2 is currently active.
11
Ultra DMA mode 3 is currently active.
12
Ultra DMA mode 4 is currently active.
13
Ultra DMA mode 5 is currently active.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
4.3.2
Bit
Word 93
13
1 = 80-conductor cable detected, CBLID above VIH
0 = 40-conductor cable detected, CBLID below VIL
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the
Features register are defined as follows:
Table 7:
Set Features command values
02H
Enable write cache (default).
03H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00H Set PIO mode to default (PIO mode 2).
01H Set PIO mode to default and disable IORDY (PIO mode 2).
08H PIO mode 0
09H PIO mode 1
0AH PIO mode 2
0BH PIO mode 3
0CH PIO mode 4 (default)
20H Multiword DMA mode 0
21H Multiword DMA mode 1
22H Multiword DMA mode 2
40H Ultra DMA mode 0
41H Ultra DMA mode 1
42H Ultra DMA mode 2
43H Ultra DMA mode 3
44H Ultra DMA mode 4
45H Ultra DMA mode 5
55H
Disable read look-ahead (read cache) feature.
82H
Disable write cache
AAH
Enable read look-ahead (read cache) feature (default).
F1H
Report full capacity available
Note.
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
29
4.3.3
S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
commands and implementation, see the Draft ATA-5 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:
http://seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the
drive uses.
Table 8:
S.M.A.R.T. commands
Code in features register
S.M.A.R.T. command
D0H
S.M.A.R.T. Read Data
D1H
Vendor-specific
D2H
S.M.A.R.T. Enable/Disable Attribute Autosave
D3H
S.M.A.R.T. Save Attribute Values
D4H
S.M.A.R.T. Execute Off-line Immediate (runs DST)
D5H
S.M.A.R.T. Read Log Sector
D6H
S.M.A.R.T. Write Log Sector
D7H
Vendor-specific
D8H
S.M.A.R.T. Enable Operations
D9H
S.M.A.R.T. Disable Operations
DAH
S.M.A.R.T. Return Status
Note.
30
If an appropriate code is not written to the Features Register, the command is aborted and 0x 04
(abort) is written to the Error register.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
5.0
Seagate Technology support services
Internet
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is
available 24 hours daily by email for your questions.
Presales Support:
Presales@Seagate.com
Technical Support:
DiscSupport@Seagate.com
Warranty Support:
http://www.seagate.com/support/service/index.html
mySeagate
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides
self-service access to critical applications, personalized content and the tools that allow our partners to
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,
password-protected Web interface-anytime, anywhere in the world.
spp.seagate.com
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You
may register for customized communications that are not available on the web. These communications contain
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.
Seagate Service Centers
Presales Support
Our Presales Support staff can help you determine which Seagate products are best suited for your specific
application or computer system, as well as product availability and compatibility.
Technical Support
Seagate technical support is available to assist you online at support.seagate.com or through one of our call
centers. Have your system configuration information and your “ST” model number available.
SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or
comments 24 hours daily and exchange messages with a technical support specialist during normal business
hours for the call center in your region.
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
31
Customer Service Operations
Warranty Service
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct
customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate
warranty service for assistance. Have your serial number and model or part number available.
Data Recovery Services
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery
services labs are currently located throughout the world. . Additional information, including an online request
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx
Authorized Service Centers
Seagate Service Centers are available on a global basis for the return of defective products. Contact your
customer support representative for the location nearest you.
USA/Canada/Latin America support services
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.
Global Customer Support
Presales, Technical, and Warranty Support
Call Center
Toll-free
USA, Canada,
and Mexico
1-800-SEAGATE
Data Recovery Services
Call Center
USA, Canada,
and Mexico
Toll-free
1-800-475-01435
Direct dial
+1-405-324-4700
Direct dial
+1-905-474-2162
FAX
1-800-475-0158
+1-905-474-2459
Europe, the Middle East and Africa Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.
Asia/Pacific Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,
go to the "Contact Us" page on www.seagate.com.
32
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
Index
A
ACA 14
acoustics 4, 12
Address 23
Agency certification 13
Altitude 10
Altitude, nonoperating 4
Altitude, operating 4
Ambient temperature 4, 10
ambient temperature 7
Annualized Failure Rate (AFR) 4
Areal density 3, 6
ATA commands 23
ATA data-transfer modes supported 3
Australia/New Zealand Standard AS/NZS3548 1995
14
Australian Communication Authority (ACA) 14
Australian C-Tick 14
Average seek time 7
Average seek, read 4
Average seek, write 4
B
bels 4
BPI 3
buffer 3, 6
Bytes per sector 3, 5
C
cables and connectors 18
Cache 3
cache 6
capacity 5
case temperature 10
CE mark 13
certification 13
Check Power Mode 24
chemical substances 15
Class B computing device 14
compatibility 13
Conducted noise 10
Conducted RF immunity 12
Configuring the drive 17
connectors 18
CSA C22.2 (950) 13
current 3
cycles 13
Cylinders 5
cylinders 3
D
data-transfer rates 1
DC power 8
Default logical geometry 5
Default sectors per track 3
density 3
Device Configuration Freeze Lock 23
Device Configuration Restore 23
Device Configuration Set 23
Diagnostics 23
dimensions 19
Discs 3
dissipation 8
Download Microcode 23
E
ead/write heads 3
Electrical fast transient 12
Electromagnetic compatibility 13
Electromagnetic Compatibility Directive (89/336/EEC)
13
Electromagnetic immunity 12
Electrostatic discharge 12
electrostatic discharge (ESD) 17
EN 55022, Class B 13
EN 55024 13
EN 60950 13
Environmental protection 15
Environmental specifications 10
EPRML 6
error-correction algorithms 1
errors 4, 13
ESD 17
EU 13
European Union (EU) requirements 13
European Union Restriction of Hazardous Substances 15
evice Configuration Identify 23
Execute Device Diagnostics 23
F
FCC verification 14
features 1
Federal Communications Commission 14
Flush Cache 23
Flush Cache Extended 23
Formatted capacity 5
Formatted Gbytes 3
Freeze Lock 23
G
Gbytes 5
geometry 5
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
33
gradient 4
Guaranteed sectors 3, 5
guaranteed sectors 5
H
handling 17
Handling precautions 17
heads 3, 5
Height 3
height 6
Humidity 10
humidity 4
I
I/O data-transfer rate 3, 6
Identify 23
Identify Device 23
Identify Device command 26
Idle 8, 24
Idle Immediate 24
Idle mode 4
Idle mode power 8
IEC950 13
Information Technology Equipment (ITE) 13
Initialize Device Parameters 23
Input noise ripple 10
Interface 6
interface 21
Interleave 6
Internal data transfer rate 3
Internal data-transfer rate 6
is 7
ISO document 7779 12
ITE 13
K
Korean RRL 14
L
latency 3
LBA mode 5
Length 3
length 6
Load/Unload 13
logical geometry 5
M
master/slave 2
Max Address 23
maximum temperature 10
Mean time between failures (MTBF) 13
Microcode 23
mounting 19
34
mounting screws 11
mounting the drive 17
N
noise 10
nominal power 7
Nonoperating shock 11
Nonoperating vibration 11
Nonrecoverable read errors 4
nonrecoverable read errors 13
O
Operating shock 11
Operating vibration 11
P
Physical characteristics 6
Physical organization 6
Physical read/write heads 3
point-to-point 2, 18
Power consumption 8
power dissipation 8
power on/off cycles 13
Power specifications 8
Power-on to Ready 7
Power-on to ready 3
precautions 17, 19
Q
quick reference 3
R
Radiated RF immunity 12
Radio and television interference 14
radio frequency (RF) 12
random track location 8
Read Buffer 23
Read DMA 23
Read DMA Extended 23
Read DMA without Retries 23
read errors 4, 13
Read Long with Retries 23
Read Long without Retries 23
Read Multiple 23
Read Multiple Extended 23
Read Native Max Address 23
Read Native Max Address Extended 23
Read Sectors 23
Read Sectors Extended 23
Read Sectors without Retries 23
Read Verify Sectors 23
Read Verify Sectors Extended 23
Read Verify Sectors without Retries 23
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
Read/write heads 5
Read/write power 4
read/write power and current 8
Recording density 3, 6
Recording method 6
Recording technology 6
Relative humidity 4, 10
Reliability 13
resistance 10
Retries 23
RF 12
RoHS 15
RPM 3
RRL 14
S
S.M.A.R.T. 24
S.M.A.R.T. implementation 23
Safety certification 13
SATA 6, 21
screws 11, 19
sector 5
sectors 5
Sectors per track 5
sectors per track 3
Security Disable Password 25
Security Erase Prepare 25
Security Erase Unit 25
Security Freeze Lock 25
Security Set Password 25
Security Unlock 25
Seek 23
seek mode 8
Seek power 4
Seek time 7
seek time 4
Seeking 8
Serial ATA 6
Serial ATA (SATA) interface 21
serial ATA ports 2
Service Life 13
servo electronics 8
Set Features 23
Set Max Address 23
Set Multiple Mode 24
Shock 11
Shock, nonoperating 4
Shock, operating 4
single-track seeks 7
Sleep 8, 24
Sleep mode 4
sound power 4
Specification summary table 3
Spindle speed 3, 6
Spinup 8
spinup power 8
Standby 8, 24
Standby Immediate 24
Standby mode 4, 8
Standby to Ready 7
Standby to ready 3
Start/stop times 7
Startup current 3
static-discharge 17
support services 31
Surge immunity 12
T
technical support services 31
temperature 4, 7, 10
Temperature gradient 4, 10
TMR 1
TPI 3
Track density 3, 6
Track-to-track seek time 4, 7
TUV North America 13
U
UL 1950 13
V
Vibration 11
Vibration, nonoperating 4
Vibration, operating 4
Voltage dips, interrupts 12
Voltage tolerance 4, 10
W
Warranty 13
Weight 3
weight 6
Wet bulb temperature 4, 10
Width 3
width 6
Write Buffer 24
Write DMA 24
Write DMA Extended 24
Write Long with Retries 24
Write Long without Retries 24
Write Multiple 24
Write Sectors 24
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
35
36
Momentus 5400.2 SATA Blade Server Product Manual, Rev. B
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100392442, Rev. B, Printed in USA
Download PDF
Similar pages