ge.com
Safety Instructions
Operating
........
2-4
Instructions
DBLR333
Control Panel .................
Control Settings .................
Features .......................
Loading and Using
the Dryer ...................
Reversing the Door ..............
Venting the Dryer ..............
Troubleshooting
Tips
S, ro
DBSR463
7
8
DBXR463
DHDSR46
DJXR433
10-11
9
11
DLLSR33
DLSR483
DQSR483
... 12, 13
DRSR483
DRSR495
Consumer Support
Consumer
Warranty
Support .....
.....................
DVLR223
Back Cover
1S
DWSR463
DWSR483
DWXR483
DX2300
DX4500
EED4500
EGD4500
Write the model and serial
numbers here:
Model #
Serial #
You can find them on a label
on the front of the drger behind the
door
175D1807P567
49-90299-1
08-06 JR
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk
of fire or explosion, electric shock, or to prevent property damage, personal injury, or
death.
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• Installation end service must be
performed by o qualified installer,
service agency or the gas supplier.
WHAT TO DO IF YOU SMELL GAS:
[] Do not try to light a match, or
cigarette, or turn on any gas or
electrical appliance.
[] Immediately
call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions carefully.
[] Do not touch any electrical switch;
do not use any phone in your building.
[] If you cannot reach your gas supplier,
call the fire department.
[] Clear the room, building or area of all
occupants.
California Safe Drinking Water and Toxic Enforcement
Act
This act requires the governor of California to publish a list of substances known to the state to cause cancer,
birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to
such substances.
Gasappliances can cause minor exposureto four of these substances,namely benzene,carbon monoxide,
formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LPfuels.
Properly adjusted dryers will minimize incomplete combustion. Exposureto these substances can be
minimized further by properly venting the dryer to the outdoors.
%
PROPERINSTALLATION
This dryer must be properlg installed and located in accordance
with the Installation Instructions
before it is used. If you did not receive an Installation Instructions sheet, you can receive one by
visiting ge.com or bg calling 800.GE.CARES (800.432.2737).
[] Properly ground dryer to conform with all
governing codes and ordinances. Follow details
in Installation Instructions.
Exhaust/Ducting
[] Install or store where it will not be exposed to
temperatures below freezing or exposed to the
weather, which could cause permanent damage
and invalidate the warranty.
]Use
only rigid metal 4" diameter ductwork inside
the dryer cabinet. Use only rigid metal or flexible
metal 4" diameter ductwork for exhausting to the
outside. USE OF PLASTIC OR OTHER
COMBUSTIBLEDUCTWORKCAN CAUSE
A FIRE.PUNCTUREDDUCTWORKCAN CAUSEA
FIREIF IT COLLAPSESORBECOMESOTHERWISE
RESTRICTED
IN USEORDURINGINSTALLATION.
[] Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
[] Remove all sharp packing items and dispose of
all shipping materials properly.
]Gas
dryers MUST be exhausted to the outside.
For complete details,follow the Installation
Instructions.
ge.com
WARNING!
YOUR LAUNDRY AREA
• Keep the area underneath and around your
appliances free of combustible materials,
(lint, paper,rags, etc.),gasoline, chemicals and
other flammable vapors and liquids.
• Keep all laundry aids (such as detergents,
bleaches, etc.)out of the reach of children,
preferably in a locked cabinet. Observe all
warnings on container labels to avoid injury.
• Keep the floor around your appliances clean
and dry to reduce the possibility of slipping.
• Never climb on or stand on the dryer top.
• Close supervision is necessary if this appliance is
used by or near children. Do not allow children to
play on, with or inside this or any other appliance.
WHEN USING YOUR DRYER
Never reach into the dryer while the drum is
moving. Before loading, unloading or adding
clothes, wait until the drum has completely
stopped.
Clean the lint filter before each load to prevent lint
accumulation inside the dryer or in the room. DO
NOT OPERATETHE DRYERWITHOUTTHE LINT
FILTERIN PLACE.
• Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted
with combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers,dry-cleaning
solvents, kerosene,etc.).These substances give
off vapors that may ignite or explode. Do not add
these substances to the wash water Do not use
or place these substances around your washer
or dryer during operation.
• Do not place items exposed to cooking oils in
your dryer Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a clothes load to catch fire.
• Any article on which you have used a cleaning
solvent or that contains flammable materials
(such as cleaning cloths, mops, towels used in
beauty salons, restaurants or barber shops,etc.)
must not be placed in or near the dryer until
solvents or flammable materials have been
removed. There are many highly flammable items
used in homes such as acetone, denatured alcohol,
gasoline, kerosene, some household cleaners, some
spot removers, turpentines, waxes, wax removers
and products containing petroleum distillates.
• The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer's
care instructions.
Do not dry articles containing rubber, plastic
or similar materials such as padded bras, tennis
shoes,galoshes, bath mats, rugs, bibs, baby pants,
plastic bags, pillows, etc. that may melt or bum.
Some rubber materials, when heated, can under
certain circumstances produce fire by spontaneous
combustion.
• Do not store plastic, paper or clothing that may
burn or melt on top of the dryer during operation.
• Garments labeled Dry Away from Heot or Do Not
Tumble Dry (such as lifejackets containing Kapok)
must not be put in your dryeE
• Do not dry fiberglass articles in your dryer
Skin irritation could result from the remaining
particles that may be picked up by clothing
during subsequent dryer uses.
• To minimize the possibility of electric shock, unplug
this appliance from the power supply or disconnect
the dryer at the household distribution panel by
removing the fuse or switching offthe circuit
breaker before attempting any maintenance or
cleaning (except the removal and cleaning of the
lint filter).NOTE:Turning the Cycle Selector knob
to an off position or pressing PAUSEdoes NOT
disconnect the appliance from the power supply.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
WHEN USING YOUR DRYER (cont.)
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a
damaged cord or plug.
• The interior of the machine and the exhaust duct
connection inside the dryer should be cleaned at
least once a year by a qualified technician. See the
Loading and Using the Drblersection.
• If yours is a gas dryer, it is equipped with an
automatic electric ignition and does not have
a pilot light. DO NOTATTEMPTTO LIGHTWITH
A MATCH.Burns may result from having your hand
in the vicinity of the burner when the automatic
ignition turns on.
You may wish to soften your laundered fabrics
or reduce the static electricity in them by using
a dryer-applied fabric softener or an anti-static
conditioneE We recommend you use either a
fabric softener in the wash cycle, according to
the manufacturer's instructions for those products,
or try a dryer-added product for which the
manufacturer gives written assurance on the
package that their product can be safely used
in gour drgen Service or performance problems
caused bg use of these products are the
responsibility of the manufacturers of those
products and are not covered under the
warranty to this appliance.
._.,.@_WHEN NOT USING YOUR DRYER
• Grasp the plug firmly when disconnecting this
appliance to avoid damage to the cord while
pulling. Place the cord away from traffic areas
so it will not be stepped on, tripped over or
subjected to damage.
• Before discarding a dryer, or removing it from
service, remove the dryer door to prevent children
from hiding inside.
• Do not tamper with controls.
• Do not attempt to repair or replace ang part of
this appliance or attempt ang servicing unless
specifically recommended in this Owner's Manual
or in published user-repair instructions that you
understand and have the skillsto carry out.
\l|j
..,.__
/_\'_
READAND FOLLOWTHISSAFETYINFORMATION
CAREFULLY.
SAVE THESE INSTRUCTIONS
About the drger control panel,
ge.com
You can locate _qourmodel number on the label on the front of the dryer behind the door, Throughout this manual, features and
appearance may vary from _jour model.
Model DVLR223
80 MIN
LESS DRY
START
70
0PllMOM
0SY
I TIMED
DRY)
MEDIUM HEAT
(_
_
MORE DRY
COTTONS]
AUTOMATIC
REGULARHEAT
ZO
IB
El
Model DX2300
START
80 MIN
LESS O0Y
START
9EWRINSLE20
Ig
Ipz
Models DBSR463, DBXR463, DHDSR46 and DX4500
START
FABRIC
CARE
SIGNAL
START
.....
MEDIUM
_TTONS
_E_,H_T
_SY
MEDCARt
_F_T
_t;
%•
"'Optional
features
(on some models)
No H_
la
Model
AUTO.TIC
.........
low H_
u
DBLR333
FABRIC
CARE
MOREDRY
LESS DRY
LESSDOY
MEDIUM
START
Push to _$#_t
(2)
30
IB'
I!1
_
El
NOTE: Drying times will vary according to the type of heat used (Electric, Natural or LP gas), size of load,
types of fabrics, wetness of clothes and condition of exhaust ducts.
About the drger control panel.
You can locate gour model number on the label on the front of the dryer behind the door. Throughout
appearance mag varg from gour model.
this manual, features and
Models DJXR433, DWSR483, DWXR483 and DLSR483
START
FARRJC
STA_
CARE
C0_TONS
_o._
WRINKLE
CARE
SIGNAL
ME01U_
_SY_RE
,_O.F_
ON
0_:
LOUO
AUTOMAte
D_UC4_S
J[!
....
CATESNi[
_H_T
NO,EAr
%
Optional features ...................
'D
B
(on some models)
11,
Models EED4500 and EGD4500
START
FABRIC
START
CARE
COTTONS
SIGNAL
EASY CARE
DAMPDBY_
,11
40
I1
S0
11
Model DLLSR33
FABRIC
START
CARE
3 HegtSettings
START
MOREDRY
LESS_RY
MEDIUM
11
1'
1'
Model DRSR495
SIGNAL
FABRIC
CARE
COTTONS
OFF
WRINKLE
CARE
EASY CASE
il;:ii
RE_ "E_E
i
START
©
HEAT
Models DQSR483, DRSR483 and DWSR463
SIGNAL
FABRIC
CARE
WRINKLE
4 He_t Settings
MEDIUM
COTTONS
CARE
Extended Cool Air Tumble
EASY CARE
NOHEAT
I EASY CARE J
AUTOMA77C
C_t_WN
AUTOMATIC
WRINKLEFREE
PERM_PRESS
BEUCATE$
START
©
LOWHEAT
Optional
features
(on some models)
11
....
_
.EW.S_
Z
)
.AMP..Y
11
[TIMED
DRY}
11
NOTE: Drying times will vary according to the type of heat used (Electric, Natural or LP gas), size of load,
types of fabrics, wetness of clothes and condition of exhaust ducts.
About the control settings.
ge.com
IMPORTANT: Clean the lint filter each time gou use the drger.
H
Fabric Care/Temperature
(on some models)
REGULAR For regular to heavy cottons.
or COTTONS
REG.HEAT
MEDIUM, For synthetics, blends, delicates and items labeled permanent press.
EASYCARE
MED. HEAT,
EASYCARE
or PERMA PRESS
MED. HEAT
DELICATES On some models. For delicates, synthetics and items labeled tumble dry Io_z
LOW HEAT
FLUFF For fluffing items without heat. Use the TIMED DRY cycle.
NO HEAT
Automatic cycles automatically determine fabric dryness. Select LESSDRYif you want your clothes
slightly damp at the end of the drying cycle. Select MOREDRYif you want them to feel drie[ Timed
cycles run for a selected time.
_
Drying
Cycles
COTTONS For cottons and most linens. For most loads, select OPTIMUMDRY (on some models) or
select the Preferred Regular Setting marked with an *.
EASY CARE/ For wrinkle-free,
PERMANENT
PRESS
permanent press and delicate items, and knits.
DEUCATES For delicate items, special-care fabrics and knits.
TIMED DRY Set the Cgcle Selector at the desired drying time.
DAMP DRY For leaving items partially damp.
DEWRINKLE
For removing wrinkles from items that are clean and dry or that are very lightly damp.
QUICK FLUFF For freshening or fluffing up alreadg dry clothing, fabrics, linens and pillows.Use with
FLUFFNO HEAT.Provides 10 minutes of no heat tumbling.
Start-Close
the dryer doo[ Select START.Opening the door during operation will stop the drye[
To restart the dryer, close the door and select STARTto complete the cycle.
Color Logic (on some models)
Select the correct FABRIC CARE setting.
Hatch the particular color below the words
with the same color on the Cycle Dial.
F] Choose the FABRICCAREsetting--for
this load it would be the EASYCAREMED.
HEAT(which is a particular color).
Example: Drying a load of clothing labeled
permanent press.
r-_-]Turn the Cycle Dial to the area that has
the same color as the FABRICCARE
setting gou have chosen-for this load it
would be the EASYCAREAUTOMATIQ
About the dryer features.
WRINKLE
CARE
Wrinkle Care Option (onsome models)
Use this option to minimize the wrinkles
in clothes. It provides approximately
15 minutes of no-heat tumbling after
the clothes are dry.
This option can only be used with the
COTTONSand EASVCAREcgcles,
If Uou are using the CYCLESIGNALknob
and you select the WRINKLECAREoption,
a signal will sound at the end of the drying
time and several times during the WRINKLE
CAREcycle. This will remind Uouthat it istime
to remove the clothes.
If WRINKLE CAREis not on, the dryer will stop
once the timer reaches the WRINKLE CARE
mark on the cycle dial.
SIGNAL
MEDIUM
Cgcle Signal Option (onsomemodels)
This signal will sound just before the end
of the cgcle to remind you to remove the
clothes. On some models, the signal sound
level cannot be adjusted,
NOTE:
If Uou selected the WRINKLECAREoption,
the signal will sound at the end of the drying
time and will sound several times during the
WRINKLECAREcurie. This will remind gou
that it is time to remove the clothes.
• Use the Cycle Signal especially when
drying fabrics like polyester knits and
permanent press. Thesefabrics should
be removed so wrinkles won't set in.
Automatic
• Remove garments promptly at the sound
of the signal. Place clothes on hangers so
wrinkles won't set in.
Cycle Signal ton some models)
At the end of each cgcle, there is
approximately 15 minutes of no-heat
tumbling after the laundry is dry.
A reminder signal will sound periodicallu
during this time to remind you to remove
the laundry.
Drum Lamp (on somemodels)
Before replacing the light bulb, be sure to
unplug the dryer power cord or disconnect
the dryer at the household distribution panel
bg removing the fuse or switching offthe
circuit breake_ Reach above dryer opening
from insidethe drum. Removethe bulb and
replace with the same size bulb.
Drying
Rack (onsomemodels)
A handg drying rack mag be used for drying
delicate items such as washable sweaters.
Hook the rack over the lint filter so the rack
extends into the dryer drum.
NOTE:
• The drying rock must be used with the
TIMED CYCLE.
• Do not use this drying rack when there
are other clothes in the dryer.
Stainless Steel Drum (onsomemodels)
The stainless steel used to make the dryer
drum provides the highest reliabilitg available
in a GEdrye_ If the dryer drum should be
scratched or dented during normal use,
the drum will not rust or corrode. These
surface blemishes will not affect the function
or durabilitg of the drum.
About reversing the door.
Reversing
ge.com
the Door
Toolsneeded:
[] 5tondord #2
[] Tope-tipped
Phillipsscrewdriver
putty knife
[_ Open the door and remove the filler plugs opposite the hinges. With the door completel9
open, remove the bottom screw from each hinge on the dryer face, Insert these screws
about half wau into the TOP holes, for each hinge, on the opposite side (where you
removed the filler plugs).Applu firm pressure to get the screw started in new holes.
[_] Loosentop screw from each hinge on the dryer face half wag, With one hand holding the
top of the door and the other hand holding the bottom, remove the door from the druer
bg lifting it UP and OUT.
[_] Rotate the door 180°. Insert it on the opposite side of the opening bg moving the door
IN and DOWN until the top hinge and the bottom hinge are resting on the top screws
inserted in step 1.
/\
\
I_] Removethe remaining screws from the side of the opening from which the door
was removed. With these screws,secure each hinge at the bottom. Tighten the
two top screws of each hinge. Reinsertthe plastic plugs on the side from which
the door was removed,
Loadingand using the dryer.
Always follow the fabric manufacturer's care label when laundering.
Sorting and Loading Hints
As a general rule, if clothes are sorted properly for the
washer,theg are sorted properly for the drgeE
Do not overload. This wastes energy and causes
wrinkling.
Do not add fabric softener sheetsonce the load has
become warm. They may cause fabric softener stains.
Bounce®Fabric Conditioner Dryer Sheetshove been
approved for use in all GEDryers when used in
accordance with the manufacturer's instructions.
Do not dry the following items: fiberglass items,
woolens, rubber-coated items, plastics,items with
plastic trim and foam-filled items.
Care and Cleaning of the Dryer
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control
panel and finishes may be damaged by some
laundry pretreatment soiland stain remover products.
Apply these products awag from the dryeEThe fabric
may then be washed and dried normally. Damage to
your dryer caused bg these products is not covered
by gour warranty.
The Lint Filter: Cleanthe lint filter before each
use. Moisten your fingers and reach into the filter
opening. Run your fingers acrossthe filten Havea
qualifiedtechnician vacuum the lint from the dryer
once a gear
Stainless Steel: To clean stainless steel surfaces,
use a damp cloth with a mild, non-abrasive cleaner
suitable for stainless steel surfaces. Remove the
cleaner residue, and then drg with a clean cloth.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a gear to prevent clogging.
A partially clogged exhaust can lengthen the
drying time.
Follow these steps:
IT] Turn off electrical supply bg disconnecting the
plug from the wall socket.
F_ Disconnect the duct from the dryer
F_ Vacuum the duct with the hose attachment and
reconnect the duct.
TheExhaust Hood: Checkfrom the outside that the
flaps of the hood move freely when operating. Hake
surethat there is not wildlife (birds,insects,etc.)nesting
insidethe duct or hood.
10
ge.com
Venting the Dryer
For the best drging performance, the dryer needs to be properlg vented. Thedryer will use more energy
and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in
the Installation Instructions.
[] Use onlg rigid metal 4" diameter ductwork inside the
drger cabinet. Use onlg rigid metal or flexible metal 4"
diameter ductwork for exhausting to the outside.
[] Do not use plastic or other combustible ductwork.
[] Use the shortest length possible.
[] Do not crush or collapse.
[] Avoid resting the duct on sharp objects.
[] Venting must conform to local building codes.
C
(
Correct
Venting
i
m
Incorrect
Venting
!!
Before you call for service...
R
Troubleshooting Tips
Save time and money! Review the charts on the following pages, or visit
Be.com. You may not need to call for service.
Problem
Possible Causes
What To Do
Dryer doesn't start
Dryer is unplugged
• Hake sure the dryer plug is pushed completely into
the outlet,
Fuse is blown/circuit breaker
is tripped
• Check the house fuse/circuit breaker box and replace
fuse or reset breakeENOTE:Host electric dryers use
2 fuses/breakers.
Fuse isblown/circuit breaker is
tripped; the dryer may tumble
but not heat
• Check the house fuse/circuit breaker box and replace
both fuses or reset both breakers. Your dryer may tumble
if only one fuse is blown or one breaker tripped.
Gas service is off
• Hake sure gas shutoff at dryer and main shutoff are
fully open.
Dryer shakes or
makes noise
Someshaking/noise is normal.
Dryer may be sitting unevenly
• Hove dryer to an even floor space, or adjust leveling legs
as necessary until even.
Greasy spots on clothes
Improper use of fabric softener
• Follow directions on fabric softener package.
Drying dirty items with
clean ones
• Use your dryer to dry only clean items. Dirty items can
stain clean items and the dryeE
Clothes were not
completely clean
• Sometimes stains which cannot be seen when the
clothes are wet oppeor after drying. Use proper washing
procedures before drying.
Lint filter isfull
• Clean lint screen before each load.
Improper sorting
• Sort lint producers (likechenille)from lint collectors
(likecorduroy).
Static electricity can attract lint
• See suggestions in this section under STATIC.
Overloading
• Separate large loads into smaller ones.
Paper, tissue, etc. left in pockets
• Empty all pockets before laundering clothes.
No fabric softener was used
• Try a fabric softeneE
Dryer doesn't heat
Lint on clothes
Static occurs
• Bounce® Fabric Conditioner Dryer Sheets have been
approved for use in all GEDryers when used in
accordance with the manufacturer's instructions,
Overdrging
• Try a fabric softener:
• Adjust setting to LESSDRYor DAMP DRY
Inconsistent
drying times
12
Synthetics, permanent press
and blends can cause static
• Try a fabric softener:
Type of heat
• Automatic drying times will vary according to the type
of heat used (electric, natural or LP gas),size of load,
types of fabrics, wetness of clothes and condition of
exhaust ducts.
ge.eom
Problem
Possible Causes
What To Do
Clothes take too long
to dry
Improper sorting
, Separate heavy items from lightweight items (generally,
a well-sorted washer load is a well-sorted dryer load),
Large loads of heavy fabrics
{like beach towels)
, Large,heavy fabrics contain more moisture and take
longer to dry. Separate large, heavy fabrics into smaller
loads to speed drying time.
Controls improperly set
, Notch control settings to the load you are drying.
Lint filter is full
, Cleon lint filter before every load.
Improper or obstructed
ducting
, Checkinstallation instructions for proper
ductingiventing.
, Make sure ducting is clean, free of kinks and
unobstructed.
, Checkto see if outside wall damper operates easily.
, Checkthe Installation Instructions to make sure the
dryer venting is correct.
Blown fuses or tripped
circuit breaker
Overloading/combining
Clothes are wrinkled
. Replace fuses or reset circuit breakers. Since most dryers
use 2 fuses/breakers, make sure both are operating.
loads
. Do not put more than one washer load in the dryer
at a time.
Underloading
. If you are drying only one or two items, add a few items
to ensure proper tumbling.
Overdrging
, Select a shorter drying time.
, Remove items while they still hold a slight amount of
moisture. Select a LESS DRY or DAMP DRY setting.
Clothes shrink
Letting items sit in dryer
after cycle ends
, Remove items when cycle ends and fold or hang
immediately.
Overloading
, Separate large loads into smaller ones.
Some fabrics will naturally
shrink
when washed. Others can be
safely washed, but will shrink
in the dryer
. To ovoid shrinkage, follow garment care labels exactly.
. Some items may be pressed back into shape after drying.
. If you are concerned about shrinkage in a particular
item, do not machine wash or tumble dry it.
13
Notes.
0
15
0
0
v
0
Q.
E
0
L_
14
GE Dryer Warranty.
All warrant;] service provided by our Factor;] Service Centers,
or an authorized Customer Card _ technician. To schedule service,
on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number
available when calling for service.
For The Period Oh
One Year
From the date of the
original purchase
Staple your receipt here.
Proof of the original pumhase
dote is needed to obtain
support under the warranty.
GE Will Replace:
Any part of the drger which fails due to a defect in materials or workmanship. During this
limited one-year warranty, GEwill also provide, free of charge, all labor and related service costs
to replace the defective part.
What GE Will Not Cover:
[] Service trips to gout home to teach gou how to
use the product.
[] Replacement of house fuses or resetting of circuit
breakers.
[] Improper installation, deliverg or maintenance.
[] Damage to the product caused bg accident, fire, floods
or acts of God.
[] Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commerciallg.
[] Replacement of the light bulb.
[] Products which are not defective or broken, or which
are working as described in the Owner's Manual.
[] Incidental or consequential damage caused bg possible
defects with this appliance.
[] Defects or damage due to operation in freezing
temperatures.
[] Damage caused after deliverg.
[] Product not accessible to provide required service.
I
EXCLUSIONOFIMPLIEDWARRANTIES--Yoursole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular
purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended
to the original pumhaser
and any succeeding
owner
for home use within the USA. If the product is located in an area where service by
available, you may be responsible for a trip charge or you may be required to bring
GE Service location. In Alaska, the warranty excludes the cost of shipping or service
I
I
for products purchased
a GE Authorized Servicer is not
the product to on Authorized
calls to your home.
Some states do not allow the exclusion or limitation of incidentaf or consequential
damages.
This warranty
gives you specific legal rights, and you ma_j also have other rights which var_j from state to state. To know
what _]our legal rights are, consult _jour local or state consumer- affairs office or _jour state's Attorney] General.
Warrantor:
General
Electric
Company.
Louisville,
KV 40225
15
Consumer Support.
GEAppliances Website
ge.com
Have a question or need assistance with your appliance? Trg the GEAppliances Website 24 hours a dag,
any day of the year! For greater convenience and faster service, you can now download Owner's Manuals,
order parts or even schedule service on-line.
ScheduleService
ge.com
Expert GErepair service is only one step away from your dooc Get on-line and schedule your service
at your convenience 24 hours any day of the year! Or call 800.GE.CARES
(800.432.2737)during normal business hours.
RealLife Design Studio
ge.com
GEsupports the Universal Design concept-products, services and environments that can be used by
people of all ages, sizesand capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. Fordetails of GE'sUniversal Design applications, including kitchen design ideas
for people with disabilities, check out our Website todag. Forthe hearing impaired, please call 800.TDD.GEAC
(800.833.4322).
ExtendedWarranties
ge.com
Purchase a GEextended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GEConsumer Home Serviceswill still be there after uour warrantu expires.
Parts and Accessories
ge.com
Individuals qualified to service their own appliances can have parts or accessoriessent directly to their homes
(VISA,MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed bg ang user. Other servicing
generally should be referred to qualified service personnel Caution must be exercised, since improper
servicing mag cause unsafe operation.
Contact Us
ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to:
General Hanager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
ge.com
Register your new appliance on-line--at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Printed in Canada
Download PDF
Similar pages