WEX-QM871
User Manual
Intel QM87
Rev.01, Aug. 2015
Contents
Chapter 1 Product Information ............................................................................... 4
1.1 Block Diagram ............................................................................................. 4
1.2 Features ....................................................................................................... 5
1.3 PCB Layout .................................................................................................. 7
1.4 Dimensions .................................................................................................. 9
1.5 Jumper Setting .......................................................................................... 10
1.6 Connector Function List ........................................................................... 13
1.7 Connector Definitions ............................................................................... 15
1.8 I/O Ports Power Output (max.) ................................................................. 30
Chapter 2 BIOS Setup ............................................................................................ 32
2.1 Main Menu.................................................................................................. 32
2.2 Advanced Menu ......................................................................................... 33
2.3 CPU Configuration (1/2) ............................................................................ 35
2.3 CPU Configuration (2/2) ............................................................................ 36
2.4 PCH-IO Configuration ............................................................................... 39
2.5 PCI Express Configuration ....................................................................... 40
2.6 Intel® Rapid Start Technology .................................................................. 41
2.7 SATA Configuration................................................................................... 42
2.8 Serial ATA Port Configuration – SATA 1 .................................................. 44
2.9 Serial ATA Port Configuration – SATA 2 .................................................. 45
2.10 Serial ATA Port Configuration – SATA 3 ................................................ 46
2.11 System Agent Configuration .................................................................. 47
2.12 Graphics Configuration .......................................................................... 48
2.13 DMI Configuration ................................................................................... 50
2.14 Memory Configuration ............................................................................ 51
2.15 USB Configuration .................................................................................. 52
2.16 Super I/O Configuration .......................................................................... 54
2.17 Serial Port 1 Configuration ..................................................................... 55
2.18 Serial Port 2 Configuration ..................................................................... 56
2.19 Hardware Monitor .................................................................................... 57
2.20 CPU Fan Configuration ........................................................................... 58
2.21 System Fan Configuration...................................................................... 59
2.22 Platform Misc Configuration .................................................................. 60
2.23 Power Management ................................................................................ 61
2.24 Boot Menu................................................................................................ 62
2.25 CSM Parameters ...................................................................................... 64
2
2.25 Security Menu .......................................................................................... 66
2.26 Security Boot Menu ................................................................................ 67
2.27 Exit Menu ................................................................................................. 68
Chapter 3 Drivers Installation................................................................................ 70
3.1 Intel Chipset Device Software .................................................................. 70
3.2 Intel Graphic Media Accelerator Driver ................................................... 73
3.3 LAN Driver ................................................................................................. 76
3.4 Audio Driver ............................................................................................... 79
3.5 USB Driver ................................................................................................. 80
3.6 iAMT Driver ................................................................................................ 83
Appendix A: Watchdog Timer ............................................................................... 85
Appendix B: GPIO .................................................................................................. 88
3
Chapter 1 Product Information
This chapter introduces the product features, jumper and connector information.
1.1 Block Diagram
Intel®
Haswell
4
1.2 Features
Processor
System Processor/
Chipsets
Chipset
BIOS
Intel® 4th Generation Core™ i7/i5/i3/Celeron®
Processor on board; FCBGA1364
Intel® 8 Series Chipset Family Mobile
Platform Controller Hub (PCH)
AMI
Technology DDR3/DDR3L 1333/1600 MHz SDRAM
Memory
Display
Max.
Capacity
Up to 8GB DDR3/DDR3L DRAM
Socket
1 x 204-pin DDR3/DDR3L SO-DIMM
Chipset
Intel® QM87
VRAM
Intel® Core™ integrated HD Graphics 4000
Shared system memory up to 2GB
LVDS
Dual channel 18/24-bit
VGA: Up to 1920 x 1200 @ 60Hz
Resolution HDMI: Up to 1080P @ 60Hz
LVDS: Up to 1920x1200 @ 60Hz
Dual Display VGA + LVDS, VGA + HDMI, HDMI + LVDS
Triple Display HDMI + LVDS + VGA
Interface
10/100/1000 Mbps
Controller
Intel® I210 GbE Controller
Intel® I217-LM GbE PHY
Interface
High Definition Audio
Controller
Realtek ALC662 HD CODEC
Ethernet
Audio
SATA
Max. Data
Transfer SATA III 600MB/s
Rates
Port
Expansion Slot
Onboard
Pin-Header
Mini-PCIe
2 x SATA III
1 (Full-size w/ mSATA)
USB 2.0
4
SATA III
2
LVDS
1
5
COM
1 x RS-232/422/485
Audio
1 (Line-in, Line-out, Mic-in)
Front Panel 1
Rear I/O
Power
DIO
8-bit programmable digital input/output
VGA
1
COM
1 x RS-232
LAN
2 x RJ45
HDMI
1
USB 3.0
2
DC 12V Input 1x2*2-pin ATX power connector for DC +12V input
Interval
Programmable 1~255 sec/min
Output
System reset
Watchdog Timer
Operating
Temp.
Environment
Form Factor
0°C~60°C
Storage
Temp.
-20°C~80°C
Relative
Humidity
0%~ 95% (non-condensing)
Dimension
146mm x 102mm (5.75” x 4.01”)
(L x W)
6
1.3 PCB Layout
Top View
7
Bottom View
MINI-PCIe
Rear I/O View
COM1
VGA
HDMI
8
USB1
LAN1
LAN2
1.4 Dimensions
9
1.5 Jumper Setting
JCMOS: CMOS Clear
Pin No.
1-2
2-3
Function
Normal Operation (Default)
Clear CMOS Contents
3 2 1
3 2 1
Jumper
Setting
JLVDS: LCD Power (+3.3V/+5V) Selection
Pin No.
1-2
2-3
Function
LCD Power +3.3V (Default)
LCD Power +5V
3 2 1
3 2 1
Pin No.
1-2
2-3
Function
Normal Operation (Default)
Clear ME Contents
Jumper
Setting
3 2 1
3 2 1
Jumper
Setting
JME: ME Clear
JPWR: AT/ATX Mode Selection
Pin No.
1-2
2-3
Function
AT Mode
ATX Mode (Default)
3 2 1
3 2 1
Jumper
Setting
10
JLVDS1: LCD Panel Type Selection
Jumper Setting
LCD Panel Type
Jumper Setting
800 x 600
18bit
LCD Panel Type
1024 x 768
18bit
(Default)
1024 x 768
24bit
1280 x 768
18bit
1280 x 800
1280 x 960
18bit
18bit
1280 x 1024
24bit
1366 x 768
18bit
1366 x 768
24bit
1440 x 900
24bit
1440 x 1050
24bit
1600 x 900
24bit
1680 x 1050
24bit
1600 x 1200
24bit
1920 x 1080
24bit
1920 x 1200
24bit
11
JMINI-PCIE: Mini-PCIE_or mSATA Function Selection
Pin No.
1-2
2-3
Function
Mini-PCIe (Default)
mSATA
3 2 1
3 2 1
Jumper
Setting
JCOM: SP339E RS232/422/485 Slew Rate Selection
Pin No.
1-2
2-3
Function
250Kbps (Default)
1Mbps
3 2 1
3 2 1
Jumper
Setting
12
1.6 Connector Function List
Rear I/O Port List
Connector
Function
COM1
Serial port connector
LAN1, LAN2
RJ45 connector
USB1
USB3.0 connector
HDMI
HDMI port connector
VGA
VGA connector
Note
OnBoard Expansion Slot List
Connector
Function
CHA-DIMM1
DDR3/DDR3L SO-DIMM connector
MINI-PCIE
Mini-PCI Express connector/mSATA (share)
Note
OnBoard I/O Connector List (1/2)
Connector
Function
AUDIO
Line-in/MIC-in/Line-out with box-header
SATA1, SATA2
SATA III connector
SATA_PWR
SATA Power with box-header
COM2
Serial port connector with box-header
CPUFAN
CPUFAN 4-pin connector
DIO
Digital I/O with pin-header
SYSFAN
System FAN connector
INV
LCD inverter with box-header
JFRONT
Front Panel with pin-header
LPC
Reserved for debug
SMB
SMBUS with pin-header
JCOM
LVDS
SP339E RS232/422/485 Slew Rate select
mSATA
(share)
LVDS connector
PWR1
ATX 2x2 connector
13
Note
OnBoard I/O Connector List (2/2)
Connector
Function
USB2,USB3
USB2.0 with box-header
BAT
CMOS BAT (CR2032) with box-header
SPI1
Reserved for debug
14
Note
1.7 Connector Definitions
The following sections provide pin definitions and detailed description of all on-board
connectors. The connector definitions follow the following notation:
Column
Name
Description
Pin
Shows the pin-numbers in the connector. The graphical layout of the
connector definition tables is made similar to the physical connectors.
Type
Al
Analog Input.
AO
Analog Output.
I
Input, TTL compatible if nothing else stated.
IO
Input / Output TTL compatible if nothing else stated.
IOT
Bi-directional tri-state IO pin.
IS
Schmitt-trigger input, TTL compatible.
IOC
Input/open-collector Output, TTL compatible.
IOD
Input / Output, CMOS level Schmitt-triggered (open drain output).
NC
Pin not connected.
O
Output, TTL compatible.
OC
Output, open-collector or open-drain, TTL compatible.
OT
Output with tri-state capability, TTL compatible.
DIFF
Differential Signal.
PWR
Power supply or ground reference pins.
IOH
Typical current in mA flowing out of an output pin through a
grounded load, while the output voltage is > 2.4 V DC (if nothing
else stated).
IOL
Typical current in mA flowing into an output pin from a VCC
connected load, while the output voltage is < 0.4 V DC (if nothing
else stated).
Signal
The mnemonic name of the signal at the current pin. The notation “XX#”
states that the signal “XX” is active low.
Note
Special remarks concerning the signal.
※ The abbreviation TBD is used for specifications which are not available yet or which are
not sufficiently specified by the component vendors.
15
Rear I/O Port Pin Define
VGA
COM1
HDMI
USB1
LAN1
LAN2
COM1: RS-232 Serial Port (DB9) Connector
COM1
Signal
Pin
Type
Note
1
2
3
4
5
6
7
8
9
I
I
O
O
PWR
I
O
I
I
Pin
Type
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
DIFF
PWR
DIFF
DIFF
PWR
DIFF
DIFF
PWR
DIFF
DIFF
PWR
DIFF
NC
NC
IO
IO
PWR
PWR
I
HDMI TMDS2+
Ground
HDMI TMDS2HDMI TMDS1+
Ground
HDMI TMDS1HDMI TMDS0+
Ground
HDMI TMDS0HDMI TMDS_CLK+
Ground
HDMI TMDS_CLKNot connected
Not connected
HDMI DDC clock
HDMI DDC data
Ground
HDMI power +5V
HDMI Hot plug detect
RS-232
Data Carrier Detect (DCD)
Received Data (RXD)
Transmitted Data (TXD)
Data Terminal Ready (DTR)
Ground
Data Set Ready (DSR)
Request To Send (RTS)
Clear To Send (CTS)
Ring Indicator (RI#)
COM1
RS-232
HDMI: HDMI Connector
HDMI
Note 1: HDMI port pin.15 (DDC Clock) and pin.16 (DDC Data) Pull Up +5V/2.2KΩ.
16
Note
1
1
LAN1, LAN2: RJ45 (LAN) Connectors
LAN1, LAN2
Pin
Type
Signal
P1
P2
DIFF
DIFF
MDI0+ / TXD+
MDI0- / TXD-
P3
DIFF
MDI1+ / RXD+
P4
DIFF
MDI2+
P5
DIFF
MDI2-
P6
DIFF
MDI1- / RXD-
P7
DIFF
MDI3+
P8
DIFF
MDI3-
Note
RJ45
USB1: USB3.0 Connectors
USB1
Pin
Type
Signal
10
11
PWR
DIFF
USB3.0 P2 power +5V (Note 1)
USB2.0 P1_D-
12
DIFF
USB2.0 P1_D+
13
PWR
Ground
14
DIFF
USB3.0 P2_RX-
(UP)
15
DIFF
USB3.0 P2_RX+
(Blue)
16
PWR
Ground
17
DIFF
USB3.0 P2_TX-
18
DIFF
USB3.0 P2_TX+
1
PWR
USB3.0 P1 power +5V (Note 1)
2
DIFF
USB2.0 P0_D-
3
DIFF
USB2.0 P0_D+
4
PWR
Ground
USB 3.0
5
DIFF
USB3.0 P1_RX-
(DOWN)
6
DIFF
USB3.0 P1_RX+
(Blue)
7
PWR
Ground
8
DIFF
USB3.0 P1_TX-
9
DIFF
USB3.0 P1_TX+
Note 1: USB3.0 port power supply maximum +5V/0.9A
17
Note
USB 3.0
VGA: VGA (DB15) Connector
VGA
Pin
Type
Signal
1
2
AO
AO
VGA Red color values
VGA Green color values
3
AO
VGA Blue color values
4
NC
Not connected
5
PWR
Ground
6
PWR
Ground
7
PWR
Ground
8
PWR
Ground
9
PWR
VGA power +5V
10
PWR
Ground
11
NC
Not connected
12
IO
VGA DDC data
13
O
VGA Horizontal synchronization
14
O
VGA Vertical synchronization
15
IO
VGA DDC clock
Note 1: VGA port pin.12 (DDC Data) and pin.15 (DDC Clock) Pull Up +5V/2.2KΩ.
18
Note
1
1
OnBoard Expansion Slot Pin Define
CHA-DIMM1: DDR3/DDR3L SO-DIMM Slot (1/3)
Signal
Pin
Type
1
2
PWR
PWR
3
4
IO
DQ4
DQ0
IO
5
6
IO
DQ5
DQ1
IO
7
8
PWR
Ground
PWR
9
10
DIFF
DQS0#
I
11
12
DIFF
DQS0
PWR
13
14
PWR
Ground
DQ2
IO
15
16
IO
DQ6
DQ3
IO
17
18
IO
DQ7
PWR
19
20
PWR
DQ8
IO
21
22
IO
DQ12
DQ9
IO
23
24
IO
DQ13
Ground
PWR
25
26
PWR
DQS1#
DIFF
27
28
I
DM1
DQS1
DIFF
29
30
I
Reset#
Ground
PWR
31
32
PWR
Ground
DQ10
IO
33
34
IO
DQ14
DQ11
IO
35
36
IO
DQ15
PWR
37
38
PWR
DQ16
IO
39
40
IO
DQ20
DQ17
IO
41
42
IO
DQ21
Ground
PWR
43
44
PWR
DQS2#
DIFF
45
46
I
DQS2
DIFF
47
48
PWR
Ground
PWR
49
50
IO
DQ22
DQ18
IO
51
52
IO
DQ23
DQ19
IO
53
54
PWR
PWR
55
56
IO
DQ28
DQ24
IO
57
58
IO
DQ29
DQ25
IO
59
60
PWR
Ground
PWR
61
62
DIFF
DQS3#
I
63
64
DIFF
DQS3
PWR
65
66
PWR
Ground
DQ26
IO
67
68
IO
DQ30
DQ27
IO
69
70
IO
DQ31
VREF_DQ
Ground
Ground
DM0
Ground
Ground
Ground
Ground
Ground
DM3
Ground
Type
Pin
IO
CHA-DIMM1
19
Signal
Ground
Ground
Ground
Ground
Ground
DM2
Ground
Ground
CHA-DIMM1: DDR3/DDR3L SO-DIMM Slot (2/3)
Signal
Pin
Type
71
72
PWR
Ground
KEY
I
73
74
I
CKE1
PWR
75
76
PWR
NC
77
78
I
A15
I
79
80
I
A14
PWR
81
82
PWR
A12
I
83
84
I
A11
A9
I
85
86
I
A7
PWR
87
88
PWR
A8
I
89
90
I
A6
A5
I
91
92
I
A4
PWR
93
94
PWR
A3
I
95
96
I
A2
A1
I
97
98
I
A0
VDDQ +1.35V (Note1)
PWR
99
100
PWR
VDDQ +1.35V (Note1)
CK0
DIFF
101
102
DIFF
CK1
CK0#
DIFF
103
104
DIFF
CK1#
VDDQ +1.35V (Note1)
PWR
105
106
PWR
VDDQ +1.35V (Note1)
A10
I
107
108
I
BA1
BA0
I
109
110
I
RAS#
PWR
111
112
PWR
WE#
I
113
114
I
CS0#
CAS#
I
115
116
I
ODT0
PWR
117
118
PWR
A13
I
119
120
I
CS1#
I
121
122
NC
PWR
123
124
PWR
NC
125
126
IO
PWR
127
128
PWR
DQ32
IO
129
130
IO
DQ36
DQ33
IO
131
132
IO
DQ37
Ground
PWR
133
134
PWR
DQS4#
DIFF
135
136
I
DQS4
DIFF
137
138
PWR
Ground
PWR
139
140
IO
Ground
Type
Pin
PWR
CHA-DIMM1
KEY
CKE0
VDDQ +1.35V (Note1)
Not connected
BA2
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
Not connected
Ground
20
Signal
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
VDDQ +1.35V (Note1)
ODT1
Not connected
VDDQ +1.35V (Note1)
VREF_CA
Ground
Ground
DM4
Ground
DQ38
CHA-DIMM1: DDR3/DDR3L SO-DIMM Slot (3/3)
Signal
Pin
Type
141
143
142
144
IO
PWR
PWR
145
146
IO
DQ44
DQ40
IO
147
148
IO
DQ45
DQ41
IO
149
150
PWR
Ground
PWR
151
152
DIFF
DQS5#
I
153
154
DIFF
DQS5
PWR
155
156
PWR
Ground
DQ42
IO
157
158
IO
DQ46
DQ43
IO
159
160
IO
DQ47
PWR
161
162
PWR
DQ48
IO
163
164
IO
DQ52
DQ49
IO
165
166
IO
DQ53
Ground
PWR
167
168
PWR
DQS6#
DIFF
169
170
I
DQS6
DIFF
171
172
PWR
Ground
PWR
173
174
IO
DQ54
DQ50
IO
175
176
IO
DQ55
DQ51
IO
177
178
PWR
PWR
179
180
IO
DQ60
DQ56
IO
181
182
IO
DQ61
DQ57
IO
183
184
PWR
Ground
PWR
185
186
DIFF
DQS7#
I
187
188
DIFF
DQS7
PWR
189
190
PWR
Ground
DQ58
IO
191
192
IO
DQ62
DQ59
IO
193
194
IO
DQ63
PWR
195
196
PWR
I
197
198
NC
Not connected
PWR
199
200
IO
SMBus data
I
201
202
O
SMBus clock
PWR
203
204
PWR
DQ34
DQ35
Ground
Ground
DM5
Ground
Ground
Ground
Ground
DM7
Ground
Ground
SA0
VDDSPD +3.3V
SA1
VTT +0.675V (Note 2)
Type
Pin
IO
IO
CHA-DIMM1
Note 1: CHA-DIMM1 Slot power supply maximum +1.35V/2.0A
Note 2: CHA-DIMM1 Slot power supply maximum +0.675V/0.6A
21
Signal
DQ39
Ground
Ground
Ground
DM6
Ground
Ground
Ground
VTT +0.675V (Note 2)
MINI-PCIE: Mini-PCIe Express Slot
Signal
Type
Pin
WAKE#
Not connected
I
NC
Not connected
Pin
Type
1
3
2
4
PWR
PWR
+3.3Vaux (Note 1)
Ground
NC
5
6
PWR
+1.5V (Note2)
I
7
8
NC
Not connected
Ground
PWR
9
10
NC
Not connected
PCIE_CLOCK-
DIFF
11
12
NC
Not connected
PCIE_CLOCK+
DIFF
13
14
NC
Not connected
Ground
PWR
15
16
NC
Not connected
CLKREQ#
MINI-PCIE
KEY
Signal
KEY
Not connected
NC
17
18
PWR
Not connected
NC
19
20
NC
Ground
PWR
21
22
O
PCIE_RXN
DIFF
23
24
PWR
+3.3Vaux (Note 1)
PCIE_RXP
DIFF
25
26
PWR
Ground
Ground
PWR
27
28
PWR
+1.5V (Note 2)
Ground
PWR
29
30
O
SMBus clock
PCIE_TXN
DIFF
31
32
IO
SMBus data
PCIE_TXP
DIFF
33
34
PWR
Ground
Ground
PWR
35
36
DIFF
USB2.0 P10_D-
Ground
PWR
37
38
DIFF
USB2.0 P10_D+
+3.3Vaux (Note 1)
PWR
39
40
PWR
Ground
+3.3Vaux (Note 1)
PWR
41
42
NC
Not connected
mPCIE_SEL1
I
43
44
NC
Not connected
Not connected
NC
45
46
NC
Not connected
Not connected
NC
47
48
PWR
+1.5V (Note 2)
Not connected
NC
49
50
PWR
Ground
Not connected
NC
51
52
PWR
+3.3Vaux (Note 1)
Note 1: MINI-PCIE Slot power supply maximum +3.3Vaux/1.1A, peak 2.5A.
Note 2: MINI-PCIE Slot power supply maximum +1.5V/0.375A, peak 0.5A.
22
Ground
Not connected
PERST#
OnBoard I/O Connector Pin Define
AUDIO: Audio with Box-header
AUDIO
Box-header 2.0mm
Pin
Type
Signal
1
AI
Line-in (Right)
2
AI
Line-in (Left)
3
AI
Line-in jack detect
4
AI
Mic-in jack detect
5
AI
Mic-in (Right)
6
AI
Mic-in (Left)
7
AI
Line-out jack detect
8
PWR
9
AO
Line-out (Right)
10
AO
Line-out (Left)
Note
Audio Ground
BAT: CMOS Battery with Box-header
BAT
Box-header 1.25mm
Pin
Type
1
PWR
2
PWR
Signal
Note
CR2032 Lithium Manganese
Battery +2.5V~+3.3V
Ground
COM2: RS-232/422/485 Serial Ports with Box-header
Signal
COM2
Box-header 2.0mm
Pin
1
2
3
4
5
6
7
8
9
10
Type
I
I
I
O
O
I
O
I
PWR
NC
RS-232
RS-422/
RS-485
485 Full
Half
Data Carrier Detect
TX D-
DATA-
Data
(DCD)Set Ready
Received Data (RXD)
(DSR)
TX D+
DATA+
Request To Send
Transmitted Data
RX D+
Clear
(TXD)To Send (CTS)
Data Terminal Ready
RX D-
Ring
(DTR)Indicator (RI#)
Ground
Not connected
23
Note
COM2
RS-232
RS-422
RS-485
CPUFAN: CPU FAN 4-Pin Connector
CPUFAN
Pin
Type
1
2
3
4
PWR
PWR
I
O
Signal
Ground
CPU FAN power +12V
CPU FAN Sense
CPU FAN Control
Note
1
2
Note 1: CPUFAN pin.2 power supply maximum +12V/0.75A
Note 2: CPUFAN pin.3 sensor pull up +12V/4.7KΩ
SYSFAN: System FAN 3-Pin Connector
SYSFAN
Pin
Type
Signal
1
2
3
PWR
PWR
I
Ground
SYSFAN power +12V
SYSFAN sense
Note
1
2
Note 1: SYSFAN pin.2 power supply maximum +12V/0.75A
Note 2: SYSFAN pin.3 sensor pull up +12V/4.7KΩ
DIO: Digital I/O with Pin-header
DIO
Pin-header 2.0mm
Pin
Type
1
2
3
4
5
6
7
8
9
10
11
12
O
I
O
I
O
I
O
I
PWR
PWR
PWR
-
Signal
Digital I/O-Output0 (bit4)
Digital I/O-Input0 (bit0)
Digital I/O-Output1 (bit5)
Digital I/O-Input1 (bit1)
Digital I/O-Output2 (bit6)
Digital I/O-Input2 (bit2)
Digital I/O-Output3 (bit7)
Digital I/O-Input3 (bit3)
DIO power +12V
DIO power +5V
Ground
KEY
Note 1: DIO pin.1 Output0 (bit4) and pin.3 Output1 (bit5) power sink 8A
Note 2: DIO pin.9 power supply maximum +12V/0.5A
Note 3: DIO pin.10 power supply maximum +5V/0.5A
24
Note
1
1
2
3
INV: LCD Inverter with Box-header
INV
Box-header 2.5mm
Pin
Type
Signal
1
2
PWR
PWR
Inverter power +12V
Inverter power +12V
3
PWR
Ground
4
O
LCD Panel backlight adjustment
5
O
LCD Panel backlight enable
Note
1
1
Note 1: INV pin.1~2 total power supply maximum +12V/1.5A
SMB: SMBus with Pin-header
SMB
Pin-header 2.54mm
Pin
Type
Signal
1
2
OC
IOC
SMBus clock (+3.3V Level)
SMBus data (+3.3V Level)
3
PWR
Ground
Note
JFRONT: Front Panel with Pin-header
JFRONT
Pin-header 2.54mm
Pin
Type
1
2
O
PWR
3
Signal
Note
Power on LED
Ground
1
O
HDD LED
1
4
O
HDD LED control
5
O
Suspend LED
6
O
Suspend LED control
7
I
System Reset#
8
PWR
9
I
10
PWR
1
Ground
Power button#
Ground
Note 1: JFRONT pin.1 Power On & pin.3 HDD LED & pin.5 Suspend LED pull up +5V/470Ω/10mA
Pin-header 2.54mm
25
LVDS: LCD Panel LVDS 18/24bit Box-header
LVDS
Box-header 1.0mm
Pin
Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PWR
PWR
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
PWR
PWR
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
DIFF
PWR
PWR
PWR
PWR
PWR
PWR
Signal
Ground
Ground
LVDS_A3+
LVDS_A3LVDS_ACLK+
LVDS_ACLKLVDS_A2+
LVDS_A2LVDS_A1+
LVDS_A1LVDS_A0+
LVDS_A0Ground
Ground
LVDS_B3+
LVDS_B3LVDS_BCLK+
LVDS_BCLKLVDS_B2+
LVDS_B2LVDS_B1+
LVDS_B1LVDS_B0+
LVDS_B0Ground
Ground
LVDS power +3.3V / +5V
LVDS power +3.3V / +5V
LVDS power +3.3V / +5V
LVDS power +3.3V / +5V
Note
1, 2
1, 2
1, 2
1, 2
Note 1: LVDS pin.27~30 power voltage by jumper select +3.3V / +5V
Note 2: LVDS pin.27~30 power supply maximum +3.3V/1.0A or +5V/1.0A
PWR1: DC-IN +12V 2x2-pin (4-pole) Connector
PWR1
Pin
Type
1
2
3
4
PWR
PWR
PWR
PWR
Signal
Ground
Ground
DC-IN +12V
DC-IN +12V
26
Note
SATA1, SATA2: SATA III Port Connector
SATA1, SATA2
Pin
Type
1
2
3
4
5
6
7
PWR
DIFF
DIFF
PWR
DIFF
DIFF
PWR
Signal
Note
Signal
Note
Ground
SATA TX+
SATA TXGround
SATA RXSATA RX+
Ground
SATA_PWR: SATA Power with Box-header
SATA_PWR
Pin
Type
1
2
PWR
PWR
SATA power +5V
Ground
3
PWR
Ground
Box-header 2.5mm
4
PWR
SATA power +12V
Note 1: SATA_PWR pin.1 power supply maximum +5V/1.5A
Note 2: SATA_PWR pin.4 power supply maximum +12V/1.5A
1
2
LPC: Low Pin Count Header - (reserved for debug)
LPC
Pin-header 2.0mm
Pin
Type
Signal
1
2
3
4
5
6
7
8
9
IOC
OC
IOC
OC
IOC
PWR
IOC
PWR
I
LPC_AD0
LPC_PLTRST#
LPC_AD1
LPC_FRAME#
LPC_AD2
LPC Power +3.3V
LPC_AD3
GND
LPC33MHz
Note 1: LPC pin.2 LPC_PLTRST# pull up +3.3V/470Ω
27
Note
1
USB2: USB 2.0 Ports with Box-header
USB2
Box-header 2.0mm
Pin
Type
Signal
Note
1
2
PWR
PWR
USB2.0 P2 Power +5V
USB2.0 P3 Power +5V
3
DIFF
USB2.0 P2 D-
2
4
DIFF
USB2.0 P3 D-
2
5
DIFF
USB2.0 P2 D+
2
6
DIFF
USB2.0 P3 D+
2
7
PWR
GND
2
8
PWR
GND
2
1, 2
1, 2
Note 1: USB2 pin.1~2 power supply maximum +5V/0.5A
Note 2: For USB2.0 cabling it is required to use only Hi-Speed USB cable, specified in USB2.0
standard.
USB3: USB 2.0 Ports with Box-header
USB3
Box-header 2.0mm
Pin
Type
Signal
Note
1
2
PWR
PWR
USB2.0 P4 Power +5V
USB2.0 P5 Power +5V
3
DIFF
USB2.0 P4 D-
2
4
DIFF
USB2.0 P5 D-
2
5
DIFF
USB2.0 P4 D+
2
6
DIFF
USB2.0 P5 D+
2
7
PWR
GND
2
8
PWR
GND
2
1, 2
1, 2
Note 1: USB3 pin.1~2 power supply maximum +5V/0.5A
Note 2: For USB2.0 cabling it is required to use only Hi-Speed USB cable, specified in USB2.0
standard.
28
SPI1: SPI Count Header - (reserved for debug)
SPI1
Pin
Type
1
2
IOC
PWR
SPI_CS0_N
+V3.3M_SPI
3
IOC
SPI_SO
4
OC
SPI_HOlD_N
5
Pin-header 2.0mm
Signal
NA
6
IO
7
PWR
GND
8
IOC
SPI_SI
SPI_CK
29
Note
1.8 I/O Ports Power Output (max.)
Rear I/O Ports Power Output (max.)
Rear I/O Port Name
USB 3.0 Port
(USB1)
USB 3.0 Port
(USB1)
Ports
Power output watts
Remark
(max.)
1
+5V/0.9A
4.5W
1
+5V/0.9A
4.5W
※1. WEX-QM871 M/B total +12V maximum power output watts = +12V/4.25A (51W)
※2. WEX-QM871 M/B total +5V maximum power output watts = +5V/6.8A (34W)
※3. WEX-QM871 M/B total +3.3V maximum power output watts = +3.3V/2.1A (7W)
OnBoard Expansion Slots Power Output (max.)
Expansion Slot Name
DDR3L SO-DIMM
(CHA-DIMM1)
MiniPCIe / mSATA
Ports
Power output watts
Remark
(max.)
+1.35V/2.0A
2.7W
+0.675V/0.6A
0.405W
+3.3VS/1.1A
3.63W
MINI-PCIE / mSATA function
+1.5V/0.375A
0.563W
by
1
1
JMINI-PCIE selection
※1. WEX-QM871 M/B total +12V maximum power output watts = +12V/4.25A (51W)
※2. WEX-QM871 M/B total +5V maximum power output watts = +5V/6.8A (34W)
※3. WEX-QM871 M/B total +3.3V maximum power output watts = +3.3V/2.1A (7W)
OnBoard I/O Ports Power Output (max.) (1/2)
Board I/O Port Name
CPU Fan [Pin-Header],
pin.2 (CPUFAN)
Ports
2
Front Panel [Pin-Header],
pin.1 PWRLED (JFRONT)
Front Panel [Pin-Header],
pin.4 HDDLED (JFRONT)
1
Front Panel [Pin-Header],
pin.6 SUSLED (JFRONT)
Digital I/O [Pin-Header],
pin.9 =+12V, pin.10=+5V (DIO)
Power output watts
(max.)
Remark
+12V/0.75A
9.0W
Add SYSFAN
+5V/10mA
50mW
Power On LED
+5V/10mA
50mW
SATA HDD LED
+5VS/10mA
50mW
Suspend LED
+12V/0.5A
6.0W
+5V/0.5A
2.5W
1
30
OnBoard I/O Ports Power Output (max.) (2/2)
Board I/O Port Name
LCD Inverter [Box-Header],
pin.1/2 =+12V (INV)
Ports
1
Power output watts
Remark
(max.)
+12V/1.5A
18.0W
+3.3V/1.0A
3.3W
+5V/1.0A
5.0W
+5V/1.5A
7.5W
+12V/1.5A
18.0W
2
+5V/0.5A
2.5W
2
+5V/0.5A
2.5W
Power output voltage by
LVDS conn. [connector],
pin.27~30 (LVDS)
1
SATA Power [Box-Header],
pin.1= +5V, pin.4=+12V
(SATA_PWR)
USB 2.0 [Pin-Header],
pin.1~2 (USB2)
USB 2.0 [Box-Header],
pin.1~2 (USB3)
(JLVDS) jumper selection
Power output voltage by
(JLVDS) jumper selection
1
2.5W x2
2.5W x2
※1. WEX-QM871 M/B total +12V maximum power output watts = +12V/4.25A (51W)
※2. WEX-QM871 M/B total +5V maximum power output watts = +5V/6.8A (34W)
※3. WEX-QM871 M/B total +3.3V maximum power output watts = +3.3V/2.1A (7W)
31
Chapter 2 BIOS Setup
This chapter introduces BIOS setup information.
Power on or reboot the system board, when screen appears message as “Press DEL
to enter SETUP“. Press <DEL> key to run BIOS SETUP Utility.
Note: The BIOS configuration for reference only, it may subject to change without
prior notice.
2.1 Main Menu
Main
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced Boot Security Exit
BIOS Information
Model Name
BIOS Version
BIOS Tag
Build Date
ME Firmware Version
PCH Information
WEX-QM871
R000
0000-00-000
03/25/2014
9.0.30.1482
LynxPoint QM87 / C2
Processor Information
Intel (R) Celeron (R) CPU 2000E @ 2.20GHz
Speed
2200 MHz
Stepping
C0
Memory Information
Total Memory
Memory Frequency
4096 MB (DDR3)
1600 Mhz
System Language
[English]
System Date
System Time
Access Level
[Tue 08/18/2015]
[10:38:22]
Administrator
Choose the system
default language
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ System Date
Set system date.
□ System Time
Set system time.
32
2.2 Advanced Menu
This section allows you to configure CPU and other system devices for basic operation
through the following sub-menus.
Main
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced Boot Security Exit
Advanced
CPU Configuration
Parameters
►CPU Configuration
►PCH-IO Configuration
►SATA Configuration
►System Agent Configuration
►USB Configuration
►Super I/O Configuration
►Hardware Monitor
►Platform Misc Configuration
►Power Management
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ CPU Configuration
□ PCH-IO Configuration
□ SATA Configuration
□ System Agent Configuration
□ USB Configuration
□ Super I/O Configuration
□ Hardware Monitor
33
□ Platform Misc Configuration
□ Power Management
34
2.3 CPU Configuration (1/2)
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
CPU Configuration
Intel(R) Celeron(R) CPU 2000E @ 2.20GHz
CPU Signature
306c3
Microcode Patch
17
Max CPU Speed
2200 MHz
Min CPU Speed
800 MHz
CPU Speed
2200 MHz
Processor Cores
2
Intel HT Technology
Not Supported
Intel VT-x Technology
Supported
Intel SMX Technology
Not Supported
64-bit
Supported
EIST Technology
Supported
CPU C3 state
Supported
CPU C6 state
Supported
CPU C7 state
Supported
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
32 kB x 2
32 kB x 2
256 kB x 2
2048 kB
Active Processor Cores
Limit CPUID Maximum
[All]
[Disabled]
Number of cores to
enable in each processor
package.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Active Processor Cores
The item sets number of cores to enable in each processor package.
Choices: All, 1.
□ Limit CPUID Maximum
This feature allows the user to set the maximum CPU ID value. Enable this function to
boot the legacy operating systems that cannot support processors with extended
CPUID functions.
Choices: Enabled, Disabled.
35
2.3 CPU Configuration (2/2)
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Execute Disable Bit
Intel Virtualization Technology
Hardware Prefetcher
Adjacent Cache Line Prefetch
[Enabled]
[Enabled]
[Enabled]
[Enabled]
Boot performance mode
EIST
CPU C states
Enhanced C1 state
CPU C3 Report
CPU C6 report
C6 Latency
CPU C7 report
C7 Latency
Package C State limit
[Turbo Performance]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Short]
[CPU C7s]
[Long]
[Auto]
Package C State limit
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when combined
with a supporting OS.
Choices: Enabled, Disabled.
□ Intel Virtualization Technology
Virtualization Technology can virtually separate system resource into several parts,
thus enhance the performance when running virtual machines or multi interface
systems.
Choices: Enabled, Disabled.
□ Hardware Prefetcher
The processor has a hardware prefetcher that automatically analyzes its
requirements and prefetches data and instructions from the memory into the Level 2
cache that are likely to be required in the near future. This reduces the latency
associated with memory reads.
Choices: Enabled, Disabled.
36
□ Adjacent Cache Line Prefetch
The processor has a hardware adjacent cache line prefetch mechanism that
automatically fetches an extra 64-byte cache line whenever the processor requests
for a 64-byte cache line. This reduces cache latency by making the next cache line
immediately available if the processor requires it as well.
Choices: Enabled, Disabled.
□ Boot performance mode
The item selects the performance state.
Choices: Max Non – Turbo Performance, Max Battery, Turbo Performance.
□ EIST
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency in an effort to reduce power
consumption and heat dissipation.
Choices: Enabled, Disabled.
□ CPU C states
The item selects “Enabled” for CPU C Sates support.
Choices: Enabled, Disabled.
-
□ Enhanced C1 state
Enable or disable C1 Power state to boost system performance.
Choices: Enabled, Disabled.
-
□ CPU C3 Report
The item allows BIOS to report the CPU C3 state.
Choices: Enabled, Disabled.
-
□ CPU C6 Report
The item allows BIOS to report the CPU C6 state.
Choices: Enabled, Disabled.
-
□ C6 Latency
The item selects short or long time when BIOS reports CPU C6 state.
Choices: Short, Long.
37
-
□ CPU C7 Report
The item allows BIOS to report the CPU C7 state.
Choices: Disabled, CPU C7, CPU C7s.
-
□ C7 Latency
The item selects short or long time when BIOS reports CPU C7 state.
Choices: Short, Long.
□ Package C State limit
The item selects “Auto” to automatically set the limit for the C State package register.
Choices: C0/C1, C2, C3, C6, C7, C7s, Auto.
38
2.4 PCH-IO Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
PCI Express
Configuration Settings
PCH-IO Configuration
►PCI Express Configuration
►Intel (R) Rapid Start Technology
Azalia
[Auto]
PCH LAN Controller
Wake on LAN
[Enabled]
[Disabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ PCI Express Configuration
□ Intel® Rapid Start Technology
□ Azalia
The item controls detection of the Azalia device.
Choices: Auto, Enabled, Disabled.
□ PCH LAN Controller
The item controls Enable or disable onboard Intel® i217LM Lan function.
Choices: Enabled, Disabled.
□ Wake on LAN
The item controls Wake up function through Onboard Intel® i217LM Lan.
Choices: Enabled, Disabled.
39
2.5 PCI Express Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
PCI Express Configuration
PCI Express Clock Gating
DMI Link ASPM Control
DMI Link Extended Synch Control
[Enabled]
[Enabled]
[Disabled]
Enable or disable PCI
Express Clock Gating for
each root port.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ PCI Express Clock Gating
Enable or disable PCI Express Clock Gating for root port.
Choices: Enabled, Disabled.
□ DMI Link ASPM Control
The item controls active state power management on both North Bridge side and
South Bridge of the DMI Link.
Choices: Enabled, Disabled.
□ DMI Link Extended Synch Control
The item allows users to enable or disable DMI Link Extended Synch.
Choices: Enabled, Disabled.
40
2.6 Intel® Rapid Start Technology
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Intel (R) Rapid Start Technology
Intel (R) Rapid Start Technology
[Disabled]
Enable or disable
Intel (R) Rapid Start
Technology.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Intel® Rapid Start Technology
Enable or disable Intel® Rapid Start Technology.
Choices: Enabled, Disabled.
41
2.7 SATA Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Determines how SATA
controller(s) operate.
SATA Configuration
SATA Mode Selection
Aggressive LPM Support
SATA Controller Speed
[AHCI]
[Enabled]
[Default]
SMART Self Test
[Disabled]
►SATA 1 ‒ Empty
►SATA 2 ‒ Empty
►SATA 3 ‒ Empty
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ SATA Mode Selection
The item selects the mode for the installed SATA drives.
Choices: IDE, AHCI, RAID.
□ Aggressive LPM Support
The item enables or disables PCH entering link power state aggressively.
Choices: Enabled, Disabled.
□ SATA Controller Speed
The item indicates the maximum speed the SATA controller can support.
Choices: Default, Gen1, Gen2, Gen3.
□ SMART Self Test
The item runs SMART Self Test on all HDDs during POST.
Choices: Enabled, Disabled.
42
□ SATA 1 – Empty
□ SATA 2 – Empty
□ SATA 3 – Empty
43
2.8 Serial ATA Port Configuration – SATA 1
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Enable or Disable SATA
Port
Serial ATA Port Configuration
SATA 1
Software Preserve
Port 4
Hot Plug
SATA Device Type
Spin Up Device
Empty
Unknown
[Enabled]
[Disabled]
[Hard Disk Drive]
[Disabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Port 4
Enable or disable SATA Port.
Choices: Enabled, Disabled.
□ Hot Plug
Enable or disable hot plug function.
Choices: Enabled, Disabled.
- Enabled:
□ Mechanical Presence Switch
Choices: Enabled, Disabled.
□ SATA Device Type
The item selects SATA Device Type.
Choices: Hard Disk Drive, Solid State Drive.
□ Spin Up Device
Enable or disable the spin up device.
Choices: Enabled, Disabled.
44
2.9 Serial ATA Port Configuration – SATA 2
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Enable or Disable SATA
Port
Serial ATA Port Configuration
SATA 2
Software Preserve
Port 5
Hot Plug
SATA Device Type
Spin Up Device
Empty
Unknown
[Enabled]
[Disabled]
[Hard Disk Drive]
[Disabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Port 5
Enable or disable SATA Port.
Choices: Enabled, Disabled.
□ Hot Plug
Enable or disable hot plug function.
Choices: Enabled, Disabled.
- Enabled:
□ Mechanical Presence Switch
Choices: Enabled, Disabled.
□ SATA Device Type
The item selects SATA Device Type.
Choices: Hard Disk Drive, Solid State Drive.
□ Spin Up Device
Enable or disable the spin up device.
Choices: Enabled, Disabled.
45
2.10 Serial ATA Port Configuration – SATA 3
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Enable or Disable SATA
Port
Serial ATA Port Configuration
SATA 3
Software Preserve
Port 2
Hot Plug
SATA Device Type
Spin Up Device
Empty
Unknown
[Enabled]
[Disabled]
[Hard Disk Drive]
[Disabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Port 2
Enable or disable SATA Port.
Choices: Enabled, Disabled.
□ Hot Plug
Enable or disable hot plug function.
Choices: Enabled, Disabled.
- Enabled:
□ Mechanical Presence Switch
Choices: Enabled, Disabled.
□ SATA Device Type
The item selects SATA Device Type.
Choices: Hard Disk Drive, Solid State Drive.
□ Spin Up Device
Enable or disable the spin up device.
Choices: Enabled, Disabled.
46
2.11 System Agent Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Enable or disable CPU
Audio Device.
System Agent Configuration
CPU Audio Device
[Enabled]
►Graphics Configuration
►DMI Configuration
►Memory Configuration
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ CPU Audio Device
Enable or disable CPU SA Audio Device.
Choices: Enabled, Disabled.
□ Graphics Configuration
□ DMI Configuration
□ Memory Configuration
47
2.12 Graphics Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Graphics Configuration
Primary Display
Internal Graphics
Aperture Size
DVMT Pre-Allocated
DVMT Total Gfx Mem
[Auto]
[Auto]
[256MB]
[32M]
[256MB]
RC6 (Render Standby)
[Enabled]
Primary IGFX Boot Display
[VBIOS Default]
LVDS Control
Backlight Active Mode
Backlight Voltage Level
Backlight Control Level
[Enabled]
[DC Mode]
[+3.3V]
10
Select which of
IGFX/PEG/PCI Graphics
device should be Primary
Display Or select SG for
Switchable Gfx.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Primary Display
The item selects IGFX/PEG/PCI Graphics device as primary Display.
Choices: Auto, IGFX, PEG, PCIE.
□ Internal Graphics
The item keeps IGD enabled or disabled based on the setup options.
Choices: Auto, Enabled, Disabled.
□ Aperture Size
The item selects Aperture Size.
Choices: 128M, 256M, 512M.
□ DVMT Pre-Allocated
The item selects DVMT Pre-Allocated (Fixed) Graphics Memory size used by Internal
Graphics Device.
Choices: 32M, 64M, 96M, 128M, 160M, 192M, 224M, 256M, 288M, 320M, 352M,
384M, 416M, 448M, 480M, 512M, 1024M.
48
□ DVMT Total Gfx Mem
The item selects DVMT Total Graphics Memory size used by Internal Graphics
Device.
Choices: 128M, 256M, MAX.
□ RC6 (Render Standby)
Enable or disable Intel® Graphics Render Standby support
Choices: Enabled, Disabled.
□ Primary IGFX Boot Display
The item selects the display device which will be activated during POST.
Choices: VBIOS Default, CRT, HDMI, LVDS.
□ LVDS Control
Enable or disable LVDS Control.
Choices: Enabled, Disabled.
□ Backlight Active Mode
The item selects Backlight Active Mode.
Choices: PWM Mode, DC Mode.
□ Backlight Voltage Level
The item selects Backlight Voltage Level.
Choices: +3.3V, +5V.
□ Backlight Control Level
The item selects Backlight Control Level
Choices: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10.
49
2.13 DMI Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
DMI Configuration
DMI
X4
DMI Link ASPM Control
DMI Gen 2
[L0sL1]
[Auto]
Gen2
Enable or disable the
control of Active State
Power Management on SA
side of the DMI Link.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ DMI Link ASPM Control
The item controls Active State Power Management of the DMI Link.
Choices: Disabled, LOs, L1, LOsL1.
□ DMI Gen 2
Allow users to enable or disable DMI Gen2.
Choices: Auto, Enabled, Disabled.
50
2.14 Memory Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
NMode Support Option.
Memory Information
Memory Frequency
Total Memory
Memory Voltage
DIMM#0
CAS Latency (tCL)
Minimum delay time
CAS to RAS (tRCDmin)
Row Precharge (tRPmin)
Active to Precharge (tRASmin)
XMP Profile 1
XMP Profile 2
1600 Mhz
4096 MB (DDR3)
1.35V
4096 MB (DDR3)
11
NMode Support
Memory Scrambler
MRC Fast Boot
Memory Remap
[Auto]
[Enabled]
[Enabled]
[Enabled]
11
11
28
Not Supported
Not Supported
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ NMode Support
The item selects NMode.
Choices: Auto, 1N Mode, 2N Mode.
□ Memory Scrambler
The item supports Memory Scrambler.
Choices: Enabled, Disabled.
□ MRC Fast Boot
Enable or disable MRC Fast boot.
Choices: Enabled, Disabled.
□ Memory Remap
Allow users to enable or disable remapping the memory above 4GB.
Choices: Enabled, Disabled.
51
2.15 USB Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
USB Configuration
USB Devices :
1 Keyboard, 2 Mice, 1 Point, 3 Hubs
Legacy USB Support
XHCI Mode
EHCI Hand-off
[Enabled]
[Smart Auto]
[Disabled]
USB Ports Per-Port Disable Control
[Disabled]
Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Legacy USB Support
The item supports Legacy USB devices.
Choices: Auto, Enabled, Disabled.
□ XHCI Mode
This is workaround for OSes without XHCI hand-off support. The XHCI ownership
change should be claimed by XHCI driver.
Choices: Smart Auto, Auto, Enabled, Disabled, Manual.
□ EHCI Hand-off
This is workaround for OSes without EHCI hand-off support. The EHCI ownership
change should be claimed by EHCI driver.
Choices: Enabled, Disabled.
52
□ USB Ports Per-Port Disable Control
The item activates the capability of the motherboard to Enable or Disable each USB
Port independently.
Choices: Enabled, Disabled.
- Enabled:
USB Port #0 [Enable/Disable]
USB Port #1 [Enable/Disable]
USB Port #2 [Enable/Disable]
USB Port #3 [Enable/Disable]
USB Port #8 [Enable/Disable]
USB Port #9 [Enable/Disable]
USB Port #6 [Enable/Disable]
USB3.0 Port #0 [Enable/Disable]
USB3.0 Port #1 [Enable/Disable]
53
2.16 Super I/O Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Set Parameters of Serial
Port 1 (COMA)
Super I/O Configuration
Fintek Super I/O ‒ F81866A
►Serial Port 1 Configuration
►Serial Port 2 Configuration
Watchdog
[Disabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Serial Port 1 Configuration
□ Serial Port 2 Configuration
□ Watchdog
Enable or Disable WatchDog Timer Function.
Choices: Disabled, Unit: Second, Unit: Minute.
- Unit: Second
□ Watchdog Timer [1~255]
- Unit: Minute
□ Watchdog Timer [1~255]
54
2.17 Serial Port 1 Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Enable or Disable Serial
Port (COM)
Serial Port 1 Configuration
Serial Port
Device Settings
[Enabled]
IO=3F8h; IRQ=4;
Change Settings
[Auto]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Serial Port
Enable or disable the serial port.
Choices: Enabled, Disabled.
□ Device Settings
The item shows the Serial Port address and interrupt.
□ Change Settings
The item changes the Serial Port address and interrupt.
Choices: Auto, IO = 3F8h; IRQ4
IO = 3F8h; IRQ3, 4, 10, 11
IO = 2F8h; IRQ3, 4, 10, 11
IO = 3F8h; IRQ3, 4, 10, 11
IO = 2F8h; IRQ3, 4, 10, 11
55
2.18 Serial Port 2 Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Enable or Disable Serial
Port (COM)
Serial Port 2 Configuration
Serial Port
Device Settings
[Enabled]
IO=2F8h; IRQ=3;
Change Settings
[Auto]
Serial port Mode
[RS-232]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Serial Port
Enable or disable the serial port.
Choices: Enabled, Disabled.
□ Device Settings
The item shows the Serial Port address and interrupt.
□ Change Settings
The item changes the Serial Port address and interrupt.
Choices: Auto, IO = 2F8h; IRQ3
IO = 3F8h; IRQ3, 4, 10, 11
IO = 2F8h; IRQ3, 4, 10, 11
IO = 3F8h; IRQ3, 4, 10, 11
IO = 2F8h; IRQ3, 4, 10, 11
□ Serial Port Mode
The item changes the Serial Port active mode.
Choices: RS232, RS-485 DE#/RE Half Duplex, RS-422/485 Full Duplex.
56
2.19 Hardware Monitor
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Hardware Monitor
Smart Fan Function
►CPU Fan Configuration
►System Fan Configuration
[Enabled]
Fan Pulses per Revolution
2
CPU Temperature
System Temperature
: +35 C
: +37 C
CPU Fan Speed
Aux Fan Speed
: 5928 RPM
: N/A
CPU
DDR
+5V
+12V
VSB5V
VCC3V
VSB3V
VBAT
:
:
:
:
:
:
:
:
+1.744 V
+1.504 V
+5.129 V
+12.144 V
+5.016 V
+3.424 V
+3.424 V
+3.120 V
Enable or Disable Smart
Fan Feature.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Smart Fan Function
The item operates Smart Fan Function.
Choices: Enabled, Disabled.
□ CPU Fan Configuration
□ System Fan Configuration
□ Fan Pulses per Revolution
Choices: 2, 3, 4.
57
2.20 CPU Fan Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Smart Fan Operation Mode.
CPU Fan Configuration
CPU Fan Mode
Faster Fan
[Standard]
[Enabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ CPU Fan Mode
The item selects CPU Fan Mode.
Choices: Standard, Full Speed, Manual.
□ Faster Fan
The item operates Faster Fan.
Choices: Enabled, Disabled.
58
2.21 System Fan Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Smart Fan Operation Mode.
System Fan Configuration
System Fan Mode
Faster Fan
[Standard]
[Enabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ System Fan Mode
The item selects System Fan Mode.
Choices: Standard, Full Speed, Manual.
□ Faster Fan
The item operates Faster Fan.
Choices: Enabled, Disabled.
59
2.22 Platform Misc Configuration
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Platform Misc Configuration
Native PCIE Enable
Native ASPM
[Enabled]
[Enabled]
PCI Express Native
Support Enable/Disable.
This feature is only
available in Vista.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Native PCIE Enable
The item supports PCI Express Native.
Choices: Enabled, Disabled.
□ Native ASPM
The item supports Native ASPM for devices.
Choices: Enabled, Disabled.
60
2.23 Power Management
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced
Power Management
ACPI Sleep State
Resume By RTC Alarm
Wake by Event
Select ACPI sleep state
the system will enter
[S1 only (CPU Stop Clock)] when the SUSPEND button
is pressed.
[Disabled]
[Disabled]
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ ACPI Sleep State
The item selects ACPI Sleep state.
Choices: S1 only (CPU Stop Clock), S3 only (CPU Stop Clock).
□ Resume By RTC Alarm
Enable or disable system wake on alarm even. When enabled, system will wake upon
the hr/min/sec specified.
Choices: Enabled, Disabled.
- Enabled:
RTC Alarm Date [0~31] → 0 means “Everyday”
RTC Alarm Hours [0~23]
RTC Alarm Minutes [0~59]
RTC Alarm Seconds [0~59]
□ Wake by Event
Enable or disable Wake by Event.
Choices: Enabled, Disabled.
61
2.24 Boot Menu
Main
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced Boot Security Exit
Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
1
[On]
Quiet Boot
Fast Boot
[Disabled]
[Disabled]
GateA20 Active
Option ROM Messages
INT19 Trap Response
[Upon Request]
[Force BIOS]
[Immediate]
Number of seconds to
wait for setup
activation Key.
65535(0xFFFF) means
indefinite waiting.
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Boot Option Priorities
►CSM parameters
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Setup Prompt Timeout
The item displays number of seconds to wait for setup activation key.
□ Bootup NumLock State
Select the keyboard NumLock state.
Choices: On, Off.
□ Quiet Boot
Enable or disable the Quiet Boot function.
Choices: Enabled, Disabled.
□ Fast Boot
Enable or disable boot with initialization of minimal set of devices required to launch
active boot option.
Choices: Enabled, Disabled.
62
□ GateA20 Active
Upon Request – GA20 can be disabled using BIOS services.
Always – Do not allow disabled GA20; this option is useful when any RT codes are
executed above 1MB.
□ Option ROM Massages
This item sets display mode for option ROM.
Choices: Forces BIOS, Keep current.
□ INT19 Trap Response
BIOS reaction on INT19 trapping by Option ROM.
Choices: Immediate, Postponed.
□ CSM Parameters
63
2.25 CSM Parameters
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Boot
Launch CSM
Boot option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Launch Video OpROM policy
[Enabled]
[UEFI and Legacy]
[Do not launch]
[Legacy only]
[Legacy only]
Other PCI device ROM priority
[UEFI OpROM]
This option controls if
CSM will be launched
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Launch CSM
The item controls if CSM will be launched.
Choices: Enabled, Disabled.
□ Boot option filter
This option controls what devices system can boot to.
Choices: UEFI and Legacy, Legacy only, UEFI only.
□ Launch PXE OpROM policy
The item controls the execution of UEFI and Legacy PXE OpROM.
Choices: Do not launch, UEFI only, Legacy only.
□ Launch Storage OpROM policy
The item controls the execution of UEFI and Legacy Storage OpROM.
Choices: Do not launch, Legacy only.
64
□ Launch Video OpROM policy
The item controls the execution of UEFI and Legacy Video OpROM.
Choices: Do not launch, Legacy only.
□ Other PCI device ROM priority
It determines OpROM execution policy for devices other than Network, Storage, or
video.
Choices: UEFI OpROM, Legacy OpROM.
65
2.25 Security Menu
Main
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced Boot Security
Security Exit
Set Administrator
Password
Password Description
If ONLY the Administrator’s password is set ,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password length must be
in the following range:
Minimum length
3
Maximum length
20
Administrator Password
User Password
►Secure Boot menu
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Administrator Password
This item sets Administrator Password.
□ User Password
This item sets User Password.
□ Secure Boot menu
66
2.26 Security Boot Menu
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Security
System Mode
Secure Boot
Setup
Not Active
Secure Boot Support
[Enabled]
Secure Boot Mode
►Key Management
[Standard]
Secure Boot can be
enabled if 1.System
running in User mode
with enrolled Platform
Key (PK) 2.CSM function
is disabled
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ System Mode
The item indicates the current system mode.
□ Secure Boot
This item indicates if Secure Boot is activated or not.
□ Secure Boot Support
The item selects Enabled for Secure Boot flow control.
Choices: Enabled, Disabled.
□ Secure Boot Mode
This feature allows selection of the Secure Boot Mode between Standard and
Custom.
Choices: Standard, Custom.
□ Key Management
Key Management allows experienced users to modify Secure Boot Variables.
67
2.27 Exit Menu
Main
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc .
Advanced Boot Security Exit
Reset the system after
saving the changes.
Save Changes and Reset
Discard Changes and Exit
Restore Defaults
Save as User Defaults
Restore User Defaults
Boot Override
Launch EFI Shell from filesystem device
: Select Screen
: Select Item
Enter : Select
+/- : Change Opt.
F1 : General Help
F2 : Previous Values
F3 : Optimized Defaults
F4 : Save & Exit
ESC : Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
□ Save Changes and Reset
The item resets the system after saving the changes.
□ Discard Changes and Exit
The item resets system setup without saving any changes.
□ Restore Defaults
The item Restores/Loads Default values for all the setup options.
□ Save as User Defaults
The item saves the changes done so far as User Defaults.
□ Restore User Defaults
The item restores the User Defaults to all the setup options.
68
□ Boot Override
These items display the available devices. The number of device items that appears
on the screen depends on the number of devices installed in the system.
□ Launch EFI Shell from filesystem device
The item attempts to EFI Shell application from one of the available file system
devices.
69
Chapter 3 Drivers Installation
This chapter introduces driver installation information.
Please insert the utility CD to CD-ROM drive, the install menu will appear
automatically, if the install menu does not list suitable driver of Operate System or
appear automatically, please select corresponding driver of utility CD to install.
The Windows 7 driver installation steps are as below.
3.1 Intel Chipset Device Software
Step1: Click “Next” to continue.
70
Step 2: Read the License Agreement and click “Accept” to continue.
Step 3: Click “Install” to continue.
71
Step 4: Click “Finish” to complete setup.
72
3.2 Intel Graphic Media Accelerator Driver
Step 1: Click “Next” to continue.
Step 2: Click “Yes” to continue.
73
Step 3: Click “Next” to continue.
Step 4: Click “Next” to continue.
74
Step 5: Click “Yes” to complete setup.
75
3.3 LAN Driver
Step 1: Click “Next” to continue.
Step 2: Click “Next” to continue.
76
Step 3: Click “Next” to continue.
Step 4: Click “Install” to continue.
77
Step 5: Click “Finish” to complete setup.
78
3.4 Audio Driver
Step 1: Click “Next” to continue.
Step 2: Click “Finish” to complete setup.
79
3.5 USB Driver
Step 1: Click “Next” to continue.
Step 2: Click “Yes” to continue.
80
Step 3: Click “Next” to continue.
Step 4: Click “Next” to continue.
81
Step 5: Click “Finish” to complete setup.
82
3.6 iAMT Driver
Step 1: Click “Next” to continue.
Step 2: Click “Yes” to continue.
83
Step 3: Click “Next” to continue.
Step 4: Click “Finish” to complete setup.
84
Appendix A: Watchdog Timer
The working algorithm of the WDT function can be simply described as a counting
process. The Time-Out Interval can be set through software programming. The
availability of time-out interval is set by software.
The System Board allows users control WDT through dynamic software programming.
The WDT starts counting when it is activated. It sends out a signal to system reset,
when time-out interval ends. To prevent the time-out interval from running out, a
re-trigger signal will need to be sent before the counting reaches its end. This action
will restart the counting process.
WDT program should keep the counting process running under normal condition.
WDT should never generate a system reset unless the system runs into troubles.
The related Control Registers of WDT are all included in the following sample
program that is written in C language. User can fill a non-zero value into the Time-out
Value Register to enable/refresh WDT. System will be reset after the Time-out Value
to be counted down to zero. Or user can directly fill a zero value into Time-out Value
Register to disable WDT immediately.
To ensure a successful accessing to the content of desired Control Register, the
sequence of following program codes should be step-by-step run again when each
register is accessed.
For more information about WDT, please refer to Fintek F81866A data sheet.
There are two PnP I/O port addresses that can be used to configure WDT,
1) 0x2E:EFIR (Extended Function Index Register, for identifying CR index number)
2) 0x2F:EFDR (Extended Function Data Register, for accessing desired CR)
Below are some example codes, which demonstrate the use of WDT.
85
// Enter Extended Function Mode
outp(0x2E, 0x87);
outp(0x2E, 0x87);
// Select Logic Device 7
outp(0x2E, 0x07);
outp(0x2F, 0x07);
// Select & Enable GPIO1
outp(0x2E, 0x27);
outp(0x2F, inp(0x2F) | 0x05);
// Assign Pin 70 to be a WDTO# Signal
outp(0x2E, 0x2C);
outp(0x2F, inp(0x2F) & 0xDF);
//Clear WDTO# Status
outp(0x2E, 0xF5);
outp(0x2F, inp(0x2F) | 0x40);
// Select time unit (Second )
outp(0x2E, 0xF5);
outp(0x2F, inp(0x2F) & Count-mode Register);
// Select time unit (Minute)
outp(0x2E, 0xF5);
outp(0x2F, inp(0x2F) | Count-mode Register);
// Set Time-out Value
outp(0x2E, 0xF6);
outp(0x2F, Time-out Value Register );
// Counting of watch dog time is enable.
outp(0x2E, 0xF5);
outp(0x2F, inp(0x2F) | 0x20);
// Exit Extended Function Mode
outp(0x2E, 0xAA);
86
Definitions of Variables:
Value of Count-mode Register :
1) 0x00 -- Count down in seconds (Bit3=0)
2) 0x08 -- Count down in minutes (Bit3=1)
Value of Time-out Value Register :
1) 0x00 -- Time-out Disable
2) 0x01~0xFF -- Value for counting down
87
Appendix B: GPIO
The System Board provides 4 dedicated output ports and 4 programmable I/O ports
that can be individually configured to perform a simple I/O function. Users can
configure 4 programmable I/O ports to become an input or output port by
programming register bit of I/O Selection .To invert port value, the setting of Inversion
Register has to be made (Note). Port values can be set to read or write through Data
Register.
Note: Only 4 programmable I/O ports support.
Additionally, 4 Digital Output ports amplified signals from GPIO ports. There are
open-drain buffers, which can offer greater driving capacity up to 100mA.
For more information about GPIO, please refer to Fintek F81866A data sheet.
The related Control Registers of GPIO are all included in the following sample
program that is written in C language. To ensure a successful accessing to the
content of desired Control Register, the sequence of following program codes should
be step-by-step run again when each register is accessed.
There are two PnP I/O port addresses that can be used to configure GPIO ports,
1) 0x2E - EFER (Extended Function Enable Register, for entering Extended Function
Mode)
- EFIR (Extended Function Index Register, for identifying CR index number)
2) 0x2F - EFDR (Extended Function Data Register, for accessing desired CR)
Below are some example codes, which demonstrate the use of GPIOs.
88
// Enter Extended Function Mode
outp(0x2E, 0x87);
outp(0x2E, 0x87);
// Assign Pin111-118 to be GPIO port
outp(0x2E, 0x27);
outp(0x2F, inp(0x2F) & 0xF3);
outp(0x2E, 0x28);
outp(0x2F, inp(0x2F) | 0x20);
// Select Logic Device 6
outp(0x2E, 0x07);
outp(0x2F, 0x06);
// Enable GPIO Port
outp(0x2E, 0x30);
outp(0x2F, 0x01);
// Select GPIO Input / Output Mode
// default GPIO87/86/85/84 as Output pin, GPIO83/82/81/80 as Input pin.
outp(0x2E, 0x88);
outp(0x2F, (inp(0x2F) | 0xF0));
// Access Output value
outp(0x2E, 0x89);
outp(0x2F, (inp(0x2F) | Output Data));
// Read Input value
outp(0x2E, 0x8A);
Input Data = inp(0x2F);
// Exit Extended Function Mode
outp(0x2E, 0xAA);
89
Definitions of Variables:
Each bit in the lower nibble of each Register represents the setting of a GPIO port.
Super IO Pin
Pin Name
Bit
GPIO DIO
111
GPIO80
0
GPIO DIO-In0
112
GPIO81
1
GPIO DIO-In1
113
GPIO82
2
GPIO DIO-In2
114
GPIO83
3
GPIO DIO-In3
115
GPIO84
4
GPIO DIO-Out0
116
GPIO85
5
GPIO DIO-Out1
117
GPIO86
6
GPIO DIO-Out2
118
GPIO87
7
GPIO DIO-Out3
Value of Output Data / Input Data :
If a port is assigned to be an output port, then its respective bit can be
read/written.
If a port is assigned to be an input port, then its respective bit can be read only.
Note:
DIO-IN0/DIO-IN1/DIO-IN2/DIO-IN3 are programmed as Inputs by BIOS default.
Parameter
Conditions
** Attention: If
VinH
min +1.857V
VinL
max +0.525V
Rated Vin
-8V ~ +12V
NC Status
High by Default
DIO-IN0/DIO-IN1/DIO-IN2/DIO-IN3 are programmed as Output signal, they
can only offer a normal signal transfer.(NOT amplified signals.)
Parameter
Conditions
VoutH
3.3V thru 10k
VoutL
0V thru 1k
DIO-OUT0/DIO-OUT1/DIO-OUT2/DIO-OUT3 are fixed as Outputs by BIOS.
Parameter
Conditions
Open-drain buffer
Power-on default = Open
Driving Capacity
max 100mA continue
90
Download PDF
Similar pages