The most trusted, dependable name in projector lamp sales.

The most trusted, dependable name
in projector lamp sales.
http://www.myprojectorlamps.com
http://www.myprojectorlamps.ca
http://www.myprojectorlamps.eu
The following projector manual has not been modified or altered in any way.
Table of Contents
Table of Contents.................................................................................... 1
Usage Notice........................................................................................... 2
Safety Information..........................................................................................2
Precautions....................................................................................................3
Eye Safety Warnings......................................................................................5
Product Features............................................................................................5
Introduction............................................................................................. 6
Package Overview.........................................................................................6
Product Overview...........................................................................................7
Main Unit................................................................................................................. 7
Input / Output Connections..................................................................................... 8
Remote Control....................................................................................................... 9
Installation............................................................................................. 11
Connecting the Projector.............................................................................. 11
Connect to Computer/Notebook........................................................................... 11
Connect to Video Sources.................................................................................... 12
Powering On/Off the Projector......................................................................13
Powering On the Projector.................................................................................... 13
Powering Off the projector.................................................................................... 14
Warning Indicator.................................................................................................. 14
Adjusting the Projected Image.....................................................................15
Adjusting the Projector’s Height............................................................................ 15
Adjusting the Projector’s Zoom / Focus................................................................ 16
Adjusting Projected Image Size............................................................................ 16
User Controls........................................................................................ 17
On-screen Display Menus............................................................................17
How to operate .................................................................................................... 17
Menu Tree............................................................................................................. 18
Image.................................................................................................................... 19
Display.................................................................................................................. 23
Setup..................................................................................................................... 26
Options.................................................................................................................. 32
Appendices........................................................................................... 35
Troubleshooting............................................................................................35
Image Problems . ................................................................................................. 35
Other Problems . .................................................................................................. 38
Projector Status Indication ................................................................................... 38
Remote Control Problems ................................................................................... 39
Replacing the Lamp.....................................................................................40
Compatibility Modes.....................................................................................42
RS232 Commands.......................................................................................44
Ceiling Mount Installation.............................................................................48
Optoma Global Offices.................................................................................49
Regulation & Safety notices.........................................................................51
1
English
Usage Notice
Safety Information
The lightning flash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Important Safety Instruction
1.Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air flow.
2.Do not use the projector near water or moisture. To reduce the risk
of fire and/or electric shock, do not expose the projector to rain or
moisture.
3.Do not install near heat sources such as radiators, heaters, stoves or
any other apparatus such as amplifiers that emits heat.
4.Clean only with dry cloth.
5.Only use attachments/accessories specified by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
Optoma before you send the unit for repair.
7.Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in fire or
electric shock.
8.See projector enclosure for safety related markings.
9.The unit should only be repaired by appropriate service personnel.
English
2
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
40-41.
▀■ Warning- This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen
display “Options|Lamp Settings” menu after replacing
the lamp module (refer to page 34).
When the lamp
reaches the end
of its life, the
projector will
not turn back on
until the lamp
module has
been replaced.
To replace the
lamp, follow
the procedures
listed under
“Replacing the
Lamp” section
on pages 40-41.
▀■ Warning- When switching the projector off, please ensure
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀■ Warning- When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
3
English
Usage Notice
Do:
 Turn off and unplug the power plug from the AC outlet before
cleaning the product.
 Use a soft dry cloth with mild detergent to clean the display
housing.
 Disconnect the power plug from AC outlet if the product is
not being used for a long period of time.
Do not:
 Block the slots and openings on the unit provided for
ventilation.
 Use abrasive cleaners, waxes or solvents to clean the unit.
 Use under the following conditions:
- In extremely hot, cold or humid environments.
Ensure that the ambient room temperature is within
5 - 35°C.
Relative Humidity is 5 - 35°C, 80% (Max.),
English
4
non-condensing.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
Usage Notice
Eye Safety Warnings
▀■ Avoid staring/facing directly into the projector beam at all
times. Keep your back to the beam as much as possible.
▀■ When projector is used in a classroom, adequately supervise
students when they are asked to point out something on the
screen.
▀■ In order to minimize the lamp power, use room blinds to reduce ambient light levels.
Product Features
▀■ One built-in speaker with 2 watt amplifier
▀■ HDTV compatible (720P, 1080i/p)
▀■ BrilliantColorTM Technology
▀■ RS232 control
▀■ Rapid shutdown
5
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
Projector
Due to different
applications in
each country,
some regions
may have
different
accessories.
English
6
IR Remote Control
Power Cord 1.8m
2 × AAA Batteries
Introduction
Product Overview
Main Unit
1
7
2
6
3
5
4
9
AU
DIO-
OU
T
AU
DIO-
IN
7
8
2
1.POWER button and
LED indicator
2. Ventilation (inlet)
3. Zoom Ring
4. Focus Ring
5.
6.
7.
8.
9.
Zoom Lens
IR Receiver
Ventilation (outlet)
Input / Output Connections
Power Socket
7
English
Introduction
Input / Output Connection
1
2
3
4
VGA1-IN/SCART
S-VIDEO
VIDEO
RS232
7
AUDIO-OUT
AUDIO-IN
5
8
6
1. VGA1-In/SCART Connector
(PC Analog Signal/Component Video Input/HDTV/SCART/
YPbPr)
2. S-Video Input Connector
3. Composite Video Input Connector
4. RS-232 Connector (3-pin)
5. Power Socket
6. KensingtonTM Lock Port
7. Audio Output Connector
8. Audio Input Connector
English
8
Introduction
Remote Control
1
1. LED Indicator
2. Power On/Off
3. No Function on this model
4. No Function on this model
5. Four Directional
Select Keys
6. Re-Sync
7. No Function on this model
8. Volume +/9. Zoom
10.AV mute
11. Video
12.VGA
13.Freeze
14.S-Video
15.Contrast
16.Brightness
17.Menu
18.Keystone +/19.Source
20.Enter
21.No Function on this model
22. No Function on this model
23.Numbered keypad
(for password input)
2
22
3
21
4
20
5
19
6
18
7
17
8
16
9
15
10
14
11
23
13
12
9
English
Introduction
Using the Remote Control
Power
Refer to the “Power On/Off the Projector”
section on pages 13-14.
Confirm your item selection.
English
10
Source
Press “SOURCE” to select an input signal.
Re-SYNC
Automatically synchronizes the projector to
the input source.
Four Directional
Select Keys
Use
to select items or make
adjustments to your selection.
Keystone +/-
Adjust image distortion caused by tilting the
projector.
Brightness
Adjust the brightness of the image.
Menu
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, press
“Menu” again.
ZOOM
Zoom in on an image.
buttons to alter zoom.
Press
Contrast
Control the degree of difference between
the lightest and darkest parts of the picture.
Freeze
Press “Freeze” to pause the screen image.
Press this button again to unlock.
S-Video
Press “S-Video” to choose S-Video source.
VGA
Press “VGA” to choose VGA sources.
Video
Press “Video” to choose Composite video
source.
AV mute
Momentarily turns off/on the video.
Volume +/-
Adjust to increase / decrease the volume.
Installation
Connecting the Projector
Connect to Computer/Notebook
2
3
5
Due to the
difference in
applications
for each
country, some
regions may
have different
accessories.
4
AUDIO-OUT
VGA1-IN/SCART
S-VIDEO
VIDEO
RS232
AUDIO-IN
R
PS50426E
(*) Optional
accessory
1
1....................................................................................................Power Cord
2................................................................................................... *VGA Cable
3................................................................................................*RS232 Cable
4.........................................................................................*Audio Input Cable
5......................................................................................*Audio Output Cable
11
English
Installation
Connect to Video Sources
DVD Player, Set-top Box,
HDTV receiver
Composite Video Output
7
6
8
2
Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
3
5
AUDIO-OUT
VGA1-IN/SCART
(*) Optional
accessory
The volume of the
AUDIO OUT is
fixed and cannot
be controlled
using the volume
control either on
the projector or
the remote control.
9
S-VIDEO
VIDEO
RS232
AUDIO-IN
R
PS50426E
4
1
S-Video Output
1....................................................................................................Power Cord
2................................................................................................... *VGA Cable
3................................................................................*Composite Video Cable
4.............................................................................................. *S-Video Cable
5................................................*15-Pin to 3 RCA Component/HDTV Adaptor
6.............................................................................*3 RCA Component Cable
7................................................................................... *SCART/VGA Adaptor
8.........................................................................................*Audio Input Cable
9......................................................................................*Audio Output Cable
English
12
Installation
Powering On/Off the Projector
Powering On the Projector
1. Securely connect the power cord and signal cable. When
connected, the Power LED will turn Red.
2. Turn on the lamp by pressing “ON/STAND-BY” button either
on the top of the projector or on the remote. The Power LED
will now turn Blue. 
The startup screen will display in approximately 10 seconds.
The first time you use the projector, you can select your
preferred language from quick menu after the startup screen
displays.
3. Turn on and connect the source that you want to display on
the screen (computer, notebook, video player, etc). The projector will detect the source automatically. If not, push menu
button on the remote control and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
If you connect multiple sources at the same time, press the
“SOURCE” button or direct source keys on the remote control to switch between inputs.
ON/STAND-BY
1
Turn on the
projector first and
then select the
signal sources.
13
English
Installation
Powering off the projector
1. Press the “ON/STAND-BY” button to turn off the projector lamp. The following message will be displayed on the
screen.
Press the “ON/STAND-BY” button again to confirm, otherwise the message will disappear after 15 seconds.
When you press the “ON/STAND-BY” button a second
time, the system will show the countdown timer on the
screen.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle. When the Power LED turns Red, the
projector has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ON/STAND-BY” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and
the projector.
4. Do not turn on the projector immediately following a power
off procedure.
Contact the
nearest service
center if the
projector displays
these symptoms.
See pages
49-50 for more
information.
Warning Indicator
 When the “ON/STAND-BY” indicator flashes red (0.5 sec
off, 0.5 sec on), the projector will automatically shut down.
Please call the nearest Optoma facility for assistance.
 When the “ON/STAND-BY” indicator flashes red (1.0 sec
off, 1.0 sec on), it indicates the projector has overheated.
The projector will shut down automatically.
Under normal conditions, the projector can be switched on
again after it has cooled down.
 When the “ON/STAND-BY” indicator flashes red (0.5 sec
off, 2.0 sec on), it indicates the fan has failed.
English
14
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for
adjusting the image height.
1.Locate the adjustable foot you wish to modify on the
underside of the projector.
2.Rotate the three adjustable rings counter clockwise to
raise the projector or clockwise to lower it. Repeat with the
remaining feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
15
English
Installation
Adjusting the Projector’s Zoom / Focus
You may turn the zoom ring to zoom in or out. To focus
the image, rotate the focus ring until the image is clear.
The projector will focus at distances from 3.9 to 39.4 feet (1.2
to 12.0 meters).
Zoom Ring
Focus Ring
Adjusting Projection Image Size
4:3
16:9
C
B
A
4:3
A
English
16
16:9
B
A
C
(m)
(m)
(inch)
(m)
(m)
(inch)
1.20
0.77
30.31
1.20
0.71
27.83
2.00
1.28
50.52
2.00
1.18
46.38
2.50
1.60
63.15
2.50
1.47
57.97
3.00
1.92
75.78
3.00
1.77
69.57
4.00
2.57
101.04
4.00
2.36
92.76
5.00
3.21
126.30
5.00
2.95
115.95
6.00
3.85
151.56
6.00
3.53
139.14
7.00
4.49
176.82
7.00
4.12
162.32
8.00
5.13
202.08
8.00
4.71
185.51
9.00
5.77
227.34
9.00
5.30
208.70
10.00
6.42
252.60
10.00
5.89
231.89
11.00
7.06
277.86
11.00
6.48
255.08
12.00
7.70
303.12
12.00
7.07
278.27
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press “MENU” on the Remote Control.
2 When OSD is displayed, use
keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3. Use
by
keys to select the desired item and adjust the settings
key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” to confirm, and the screen will return to the main
menu.
6. To exit, press “MENU” again. The OSD menu will close and the
projector will automatically save the new settings.
Main Menu
Sub Menu
Settings
17
English
User Controls
Menu Tree
(QJOLVK
,0$*(
'LVSOD\0RGH
%ULJKWQHVV
3UHVHQWDWLRQ%ULJKW0RYLHV5*%%ODFNERDUG&ODVVURRP
8VHU8VHU
&RQWUDVW
6KDUSQHVV
# 6DWXUDWLRQ
#
7LQW
$GYDQFHG
,0$*(_$'9$1&('
'HJDPPD
)LOP9LGHR*UDSKLFV3&
%ULOOLDQW&RORUറ
&RORU7HPS
:DUP0HGLXP&ROG
&RORU
&RORU6SDFH
$8725*%<89
,QSXW6RXUFH
5HG*DLQ
,0$*(_$'9$1&('_
&2/25
*UHHQ*DLQ
%OXH*DLQ
5HG%LDV
*UHHQ%LDV
%OXH%LDV
&\DQ
0DJHQWD
<HOORZ
(#) “Saturation”
and “Tint” are only
supported in Video
mode.
5HVHW
,0$*(_$'9$1&('_,1387
6285&(
<HV1R
9*$
*
69LGHR
9LGHR
9*$
',63/$<
)RUPDW
(**) “Signal” is only
supported in Analog
VGA (RGB) signal.
,,,1DWLYH$872
2YHUVFDQ
=RRP
+,PDJH6KLIW
9,PDJH6KLIW
9.H\VWRQH
6(783
/DQJXDJH
(QJOLVK'HXWVFK)UDQ©DLV,WDOLDQR(VSD³RO3RUWXJX¬V
3ROVNL1HGHUODQGV̷͚͑͘͘͏͐6XRPL6YHQVND
1RUVN'DQVNˢ˨˨ˤ˪˦˧˙0DJ\DUÎHģWLQD7¾UN©H丏⇢₼㠖
僐浣₼㠖㡴㦻崭뼑霢꽩ࡷࡎ࡙᧒ᥱᦎᦫ
3URMHFWLRQ
0HQX/RFDWLRQ
**
6LJQDO
6HFXULW\
3URMHFWRU,'
0XWH
2Q2II
9ROXPH
$GYDQFHG
6(783_6,*1$/
$XWRPDWLF
(QDEOH'LVDEOH
3KDVH
)UHTXHQF\
+3RVLWLRQ
93RVLWLRQ
6(783_6(&85,7<
6HFXULW\
2Q2II
6HFXULW\7LPHU
&KDQJH3DVVZRUG
6(783_$'9$1&('
/RJR
1HXWUDO23720$
6RXUFH/RFN
2Q2II
237,216
+LJK$OWLWXGH
2Q2II
,QIRUPDWLRQ+LGH
2Q2II
%DFNJURXQG&RORU
%ODFN5HG%OXH*UHHQ:KLWH
$GYDQFHG
/DPS6HWWLQJV
237,216_$'9$1&('
5HVHW
<HV1R
'LUHFW3RZHU2Q
2Q2II
$XWR3RZHU2IIPLQ
6OHHS7LPHUPLQ
3RZHU0RGH
237,216_/$036(77,1*6
English
18
6WDQGE\$FWLYH
/DPS+RXUV
/DPS5HPLQGHU
2Q2II
%ULJKWQHVV0RGH
67'%5,*+7
/DPS5HVHW
<HV1R
User Controls
IMAGE
Display Mode
There are many factory presets optimized for various types of
images.
Presentation: Good color and brightness from PC input.
Bright: Maximum brightness from PC input.
Movie: For home theater.
sRGB: Standardised accurate color.
Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
Classroom: This mode is recommended for projecting in a
classroom.
User1: User’s settings.
User2: The initial default settings of this mode is from Movie
mode. Any further adjustments by the user in User2 will be
saved in this mode for future use.
Brightness
Adjust the brightness of the image.
Press the
Press the
to darken image.
to lighten the image.
19
English
User Controls
IMAGE
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
Press the
Press the
to decrease the contrast.
to increase the contrast.
Sharpness
Adjust the sharpness of the image.
Press the
Press the
to decrease the sharpness.
to increase the sharpness.
Saturation
Adjust a video image from black and white to fully saturated color.
“Saturation” and
“Tint” functions
are only supported
under Video mode.
Press the
Press the
to decrease the amount of saturation in the image.
to increase the amount of saturation in the image.
Tint
Adjust the color balance of red and green.
English
20
Press the
Press the
to increase the amount of green in the image.
to increase the amount of red in the image.
User Controls
IMAGE | Advanced
Degamma
This allows you to choose a degamma table that has been
fine-tuned to bring out the best image quality for the input.
Film: for home theater.
Video: for video or TV source.
Graphics: for image source.
PC: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing true, more vibrant colors in picture. The range is from
“0” to “10”. If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust
toward the minimum setting.
Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
Color Space
Select an appropriate color matrix type from AUTO, RGB or YUV.
21
English
User Controls
Advanced |Color
Color
Use these settings for advanced adjustment of the individual Red,
Green, Blue, Cyan, Magenta and Yellow Colors.
Reset
Choose “Yes” to return the factory default settings for color
adjustments.
Advanced |
Input Source
Input Source
Use this option to enable / disable input sources. Press
to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will not search for inputs that
are not selected.
English
22
User Controls
DISPLAY
Format
Use this function to choose your desired aspect ratio.
4:3: This format is for 4×3 input sources.
16:9-I: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV.
16:9-II: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV.
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
Resize image
Aspect ratio
(source detected)
SVGA model
XGA model
4:3
800 x 600 center
1024 x 768 center
16:9-I
800 x 450 center
1024 x 576 center
16:9-II
854 x 480 catch
800 x 480 center
854 x 480 center
Native
1:1 mapping center
1:1 mapping center
23
English
User Controls
Display area
Picture area
Input Signal
Display on Screen
4:3
format
or
16 : 9-I format
or
16 : 9-II format
Native format
English
24
User Controls
DISPLAY
Overscan
Overscan function removes the noise in a video image. Overscan
the image to remove video encoding noise on the edge of video
source.
Zoom
Press the
Press the
to reduce the size of an image.
to magnify an image on the projection screen.
H Image Shift
Shift the projected image position horizontally.
V Image Shift
Shift the projected image position vertically.
V Keystone
Press the or to adjust image distortion vertically and makes a
rectangular image.
25
English
User Controls
SETUP | Language
Language
Choose the multilingual OSD menu. Press or into the sub
menu and then use the
or
key to select your preferred
language. Press “Enter” to finalize the selection.
English
26
User Controls
SETUP
Projection
Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.

Front-Desktop

Rear-Desktop
This is the default selection. The image is projected straight on
the screen.
When selected, the image will appear reversed.

Front-Ceiling
When selected, the image will turn upside down.

Rear-Ceiling
When selected, the image will appear reversed in upside down
position.
Menu Location
Choose the menu location on the display screen.
Projector ID
ID definition can be set up by menu (range 0~99), and allow
user control an individual projector by RS232. Refer to page 48
for the complete list of RS232 commands.
Mute
Choose the “On” to turn mute on.
Choose the “Off” to turn mute off.
Volume
Press the to decrease the volume.
Press the to increase the volume.
27
English
User Controls
SETUP | Signal
“Signal” is only
supported in Analog
VGA (RGB) signal.
Automatic
Automatically selects the singal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns
off and on again.
Phase
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or flickers, use this function to
correct it.
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to flicker vertically.
H. Position
Press the
Press the
to move the image left.
to move the image right.
V. Position
Press the
Press the
English
28
to move the image down.
to move the image up.
User Controls
SETUP | Security
Security
On: Choose “On” to use security verification when the turning
on the projector.
Off: Choose “Off” to be able to switch on the projector without
password verification.
Security Timer
Can be select the time (Month/Day/Hour) function to set the
number of hours the projector can be used. Once this time has
elapsed you will be requested to enter your password again.
29
English
User Controls
SETUP | Security
Change Password
First time:

Pass-code default
value is “1234”
(first time).
1. Press “
” to set the password.
2. The password has to be 4 digits.
3. Use number button on the remote to enter your new
password and then press “ ” key to confirm your
password.
Change Password:
1. Press “
” to input old password.
2. Use number button to enter current password and then
press “ ” to confirm.
3. Enter new password (4 digits in length) using the number
buttons on the remote, then press “ ” to confirm.
4. Enter new password again and press “
” to confirm.
If you have forgotten your password, please contact your local
office for support.
English
30
User Controls
SETUP | Advanced
Logo
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
Optoma: The default startup screen.
Neutral: No logo is displayed.
31
English
User Controls
OPTIONS
Source Lock
On: The projector will search specified connection port.
Off: The projector will search for other signals if the current
input signal is lost.
High Altitude
When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.
Information Hide
On: Choose “On” to hide the “searching” message.
Off: Choose “Off” to show the “searching” message.
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
Reset
Choose “Yes” to return the display parameters on all menus to the
factory default settings.
English
32
User Controls
OPTIONS |
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without pressing “POWER” button either on the top of the projector or on the
remote.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).

This disables VGA
out and RJ45
control when the
projector is in
standby mode
(<1W).
Power mode
Standby: Choose “Standby” to save power dissipation further
< 1W.
Active: Choose “Active” to return to normal standby mode and
the VGA out port will be enabled.
33
English
User Controls
OPTIONS |
Lamp Settings
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement
of lamp.
Brightness Mode
STD: Choose “STD” to dim the projector lamp which will lower
power consumption and extend the lamp life by up to
130%.
BRIGHT: Choose “BRIGHT” to increase the brightness.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
English
34
Appendices
Troubleshooting
If you experience a problem with your projector,
please refer to the following information. If a
problem persists, please contact your local
reseller or service center.
Image Problems
No image appears on-screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure all the pins of connectors are not bent or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Ensure that the “AV mute” feature is not turned on.
Partial, scrolling or incorrectly displayed image
 Press “RE-SYNC” on the remote.
If you are using a PC:
For Windows 95, 98, 2000, XP:
1. Open the “My Computer” icon, the “Control Panel” folder, and
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal
to UXGA (1600 × 1200).
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also
need to change the monitor display you are using. Refer to the
following steps.
5. Verify the resolution setting is lower than or equal to UXGA
(1600 × 1200).
6. Select the “Change” button under the “Monitor” tab.
35
English
Appendices
7. Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 × 1200).
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the
computer.
2. Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]
Acer  [Fn]+[F5]
Asus  [Fn]+[F8]
Dell  [Fn]+[F8]
Gateway  [Fn]+[F4]
IBM/Lenovo 
HP/Compaq 
NEC 
Toshiba 
[Fn]+[F7]
[Fn]+[F4]
[Fn]+[F3]
[Fn]+[F5]
Mac Apple:
System Preference  Display  Arrangement  Mirror
display
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not
displaying your presentation
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s manual for detailed
information.
Image is unstable or flickering
Use “Phase” to correct it. See page 28 for more information.
Change the monitor color setting on your computer.
Image has vertical flickering bar
Use “Frequency” to make an adjustment. See page 28for more
information.
Check and reconfigure the display mode of your graphic card to
make it compatible with the projector.
English
36
Appendices
Image is out of focus
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance
3.9 to 39.4 feet (1.2 to 12.0 meters) from the projector.
See page 16.
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will
show the best image in 16:9 format on projector side.
If you play 4:3 format DVD titles, please change the format to 4:3
in the projector OSD.
If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type
on your DVD player.
Image is too small or too large
Adjust the Zoom Ring on the top of the projector.
Move the projector closer to or further from the screen.
Press “MENU” button on the remote control, go to “Display 
Format” and try the different settings.
Image has slanted sides
If possible, reposition the projector so that it is horizontally
Use of Keystone is
not recommended.
centered on the screen and below the bottom of the screen.
Press
“Keystone +/-” button on the remote control until the sides

are vertical.
Image is reversed
Select “SETUP  Projection” from the OSD and adjust the
projection direction.
37
English
Appendices
Other Problems
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on
pages 40-41.
Projector Status Indication
LED lighting message
Message
Power LED
Power LED
(Red)
(Blue)
Standby State
(Input power cord)
Flashing
Power on (Warming)
(0.5 sec off, 0.5 sec on)
Lamp lighting
Flashing
Power off (Cooling)
Error (Over Temp.)
Steady light 
No light 
English
38
(1 sec off, 1 sec on)
<10 sec to off
Flashing
(1 sec off, 1 sec on)
Flashing
Error (Fan fail)
(0.5 sec off, 2.0 sec on)
Error (Lamp fail)
(0.5 sec off, 0.5 sec on)
Flashing
Appendices
On Screen Messages
Temperature warning:
Fan failed:
Lamp warning:
Out of display range:
Remote Control Problems
If the remote control does not work
Check the operating angle of the remote control is within ±15°
both horizontally and vertically of one of the IR receivers on the
projector.
Make sure there are not any obstructions between the remote
control and the projector. Move to within 7 m (±0°) of the projector.
 Make sure the batteries are inserted correctly.
 Replace batteries if they are exhausted.
39
English
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.
When you see this message, please contact your local reseller
or service center to change the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when
opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from falling
out of projector.”
Warning: Lamp compartment may be hot! Allow it to cool down
before changing the lamp!
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
English
40
Appendices
1
2
The screws on the
lamp cover and the
lamp cannot be
removed.
3
4
The projector
cannot be turned
on if the lamp
cover has not been
placed back on the
projector.
Do not touch the
glass area of the
lamp. Hand oil can
cause the lamp to
shatter. Use a dry
cloth to clean the
lamp module if it
was accidentally
touched.
Lamp Replacement Procedure:
1. Switch off the power to the projector by pressing the “POWER” button.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Unscrew the two screws on the cover. 1
5. Lift up and remove the cover. 2
6. Unscrew the two screws on the lamp module. 3
7. Lift up the lamp handle and remove the lamp module slowly and carefully. 4
To replace the lamp module, reverse the previous steps.
8. Turn on the projector and use “Lamp Reset” after the lamp module is
replaced.
Lamp Reset: (i) Press “MENU”  (ii) Select “OPTIONS”  (iii) Select
“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.
41
English
Appendices
Compatibility Modes
Computer Compatibility
For widescreen
resolution (WXGA),
the compatibility
support is
dependent on
Notebook/PC
models.
English
42
Mode
Resolution
V-Sync (Hz)
H-Sync (KHz)
VGA
640 × 480
60
31.50
VGA
640 × 480
72
37.90
VGA
640 × 480
75
37.50
VGA
640 × 480
85
43.30
VGA
720 × 400
70
31.50
VGA
720 × 400
85
37.90
SVGA
800 × 600
56
35.20
SVGA
800 × 600
60
37.90
SVGA
800 × 600
72
48.10
SVGA
800 × 600
75
46.90
SVGA
800 × 600
85
53.70
XGA
1024 × 768
60
48.40
XGA
1024 × 768
70
56.50
XGA
1024 × 768
75
60.00
XGA
1024 × 768
85
68.70
WXGA
1280 × 768
60
47.40
WXGA
1280 × 768
75
60.30
WXGA
1280 × 800
60
49.70
SXGA
1280 × 1024
60
63.98
SXGA
1280 × 1024
75
79.98
SXGA
1280 × 1024
85
91.10
SXGA+
1400 × 1050
60
63.98
UXGA
1600 × 1200
60
75.00
Appendices
Computer Compatibility
Mode
Resolution
V-Sync (Hz)
H-Sync (KHz)
MAC LC 13”
640 × 480
66.66
34.98
MAC II 13”
640 × 480
66.68
35.00
MAC 16”
832 × 624
74.55
49.73
MAC 19”
1024 × 768
75
60.24
MAC
1152 × 870
75.06
68.68
MAC G4
640 × 480
60
31.35
i MAC DV
1024 × 768
75
60.00
i MAC DV
1152 × 870
75
68.49
i MAC DV
1280 × 960
75
75.00
Video Compatibility
NTSC
NTSC M/J, 3.58MHz, 4.43 MHz
PAL
B/D/G/H/I/M/N, 4.43 MHz
SECAM
B/D/G/K/K1/L, 4.25/4.4 MHz
SDTV
480i/p, 576i/p
HDTV
720p(50/60Hz), 1080i(50/60Hz), 1080p(24/50/60Hz)
43
English
Appendices
RS232 Commands
RS232 Pin Assignments
3
1
2
9
5
Pin no.
Pin no.
1
English
44
8
4
7
3
6
2
Spec.
1
N/A
2
RXD
OUT
3
TXD
N/A
Name
I/O (From
Projector Side)
TXD
2
RXD
IN
4
3
GND
GND
5
GND
6
N/A
7
N/A
8
N/A
9
N/A
1
Appendices
RS232 Protocol Function List
RS232 Commands
Baud Rate : 9600
Data Bits: 8
Optoma ES526L/EX536L
Parity: None RS232 Command Table
UART16550 FIFO: Disable
Projector Return (Pass): P
Projector Return (Fail): F
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Stop Bits: 1
Baud Rate : 9600
Note :
There is a <CR> after all ASCII commands
XX=00-99,
projector's ID,0D
Flow Control : None
Data Bits: 8
is the HEX code for <CR> in ASCII code
XX=00 is for all projectors
Parity: None
Stop Bits: 1
Flow Control : None 1. There is a <CR> after all ASCII commands.
UART16550 FIFO: Disable
2.P0D is the HEX code for <CR> in ASCII code.
Projector Return (Pass):
Projector Return (Fail): F
XX=01-99, projector's ID, XX=00 is for all projectors
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code
HEX Code
Function
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX00 1
7E 30 30 30 30 20 31 0D
Power ON
~XX00 0
7E 30 30 30 30 20 30 0D
Power OFF (0/2 for backward compatible)
~XX00 1 ~nnnn
7E 30 30 30 30 20 31 20 a 0D Power ON with Password
~nnnn = ~0000 (a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX01 1
7E 30 30 30 31 20 31 0D
Resync
~XX02 1
7E 30 30 30 32 20 31 0D
AV Mute
On
~XX02 0
7E 30 30 30 32 20 30 0D
Off (0/2 for backward compatible)
~XX03 1
7E 30 30 30 33 20 31 0D
Mute
On
~XX03 0
7E 30 30 30 33 20 30 0D
Off (0/2 for backward compatible)
~XX04 1
7E 30 30 30 34 20 31 0D
Freeze
~XX04 0
7E 30 30 30 34 20 30 0D
Unfreeze
(0/2 for backward compatible)
~XX05 1
7E 30 30 30 35 20 31 0D
Zoom Plus
~XX06 1
7E 30 30 30 36 20 31 0D
Zoom Minus
~XX12 5
7E 30 30 31 32 20 35 0D
VGA 1
~XX12 7
7E 30 30 31 32 20 37 0D
VGA 1 SCART
~XX12 8
7E 30 30 31 32 20 38 0D
VGA 1 Component
~XX12 9
7E 30 30 31 32 20 39 0D
S-Video
~XX12 10
7E 30 30 31 32 20 31 30 0D
Video
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX20 1
7E 30 30 32 30 20 31 0D
Display Mode
Presentation
~XX20 2
7E 30 30 32 30 20 32 0D
Bright
~XX20 3
7E 30 30 32 30 20 33 0D
Movie
~XX20 4
7E 30 30 32 30 20 34 0D
sRGB
~XX20 5
7E 30 30 32 30 20 35 0D
User1
~XX20 6
7E 30 30 32 30 20 36 0D
User2
~XX20 7
7E 30 30 32 30 20 37 0D
Blackboard
~XX20 8
7E 30 30 32 30 20 38 0D
Classroom
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX21 n
7E 30 30 32 31 20 a 0D
Brightness
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX22 n
7E 30 30 32 32 20 a 0D
Contrast
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX23 n
7E 30 30 32 33 20 a 0D
Sharpness
n = 0 (a=30) ~ 31 (a=33 31)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX24 n
7E 30 30 32 34 20 a 0D
Color Settings
Red Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX25 n
7E 30 30 32 35 20 a 0D
Green Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n
7E 30 30 32 36 20 a 0D
Blue Gain
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX27 n
7E 30 30 32 37 20 a 0D
Red Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX28 n
7E 30 30 32 38 20 a 0D
Green Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX29 n
7E 30 30 32 39 20 a 0D
Blue Bias
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX30 n
7E 30 30 33 30 20 a 0D
Cyan
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX31 n
7E 30 30 33 31 20 a 0D
Yellow
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX32 n
7E 30 30 33 32 20 a 0D
Magenta
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX33 1
7E 30 30 33 33 20 31 0D
Reset
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX34 n
7E 30 30 33 34 20 a 0D
BrilliantColorTM
n = 0 (a=30) ~ 10 (a=31 30)
~XX35 1
7E 30 30 33 35 20 31 0D
Degamma
Film
~XX35 2
7E 30 30 33 35 20 32 0D
Video
~XX35 3
7E 30 30 33 35 20 33 0D
Graphics
~XX35 4
7E 30 30 33 35 20 34 0D
PC
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX36 1
7E 30 30 33 36 20 31 0D
Color Temp.
Warm
~XX36 2
7E 30 30 33 36 20 32 0D
Medium
~XX36 3
7E 30 30 33 36 20 33 0D
Cold
~XX37 1
7E 30 30 33 37 20 31 0D
Color Space
Auto
~XX37 2
7E 30 30 33 37 20 32 0D
RGB
~XX37 3
7E 30 30 33 37 20 33 0D
YUV
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX45 n
7E 30 30 34 34 20 a 0D
Color (Saturation)
n = 0 (a=30) ~ 100 (a=31 30 30)
~XX44 n
7E 30 30 34 35 20 a 0D
Tint
n = 0 (a=30) ~ 100 (a=31 30 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX60 1
7E 30 30 36 30 20 31 0D
Format
4:3
~XX60 2
7E 30 30 36 30 20 32 0D
16:9-l
~XX60 3
7E 30 30 36 30 20 33 0D
16:9-ll
~XX60 6
7E 30 30 36 30 20 36 0D
Native
~XX60 7
7E 30 30 36 30 20 37 0D
Auto
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX61 n
7E 30 30 36 31 20 a 0D
Overscan
n = 0 (a=30) ~ 3 (a=33)
~XX62 n
7E 30 30 36 32 20 a 0D
Zoom
n = -5 (a=2D 35) ~ 25 (a=32 35)
~XX63 n
7E 30 30 36 33 20 a 0D
H Image Shift
n = -50 (a=2D 35 30) ~ +50 (a=35 30)
~XX64 n
7E 30 30 36 34 20 a 0D
V Image Shift
n = -50 (a=2D 35 30) ~ +50 (a=35 30)
~XX66 n
7E 30 30 36 36 20 a 0D
V Keystone
n = -40 (a=2D 34 30) ~ 40 (a=34 30)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
45
English
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code
HEX Code
Function
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX70 1
7E 30 30 37 30 20 31 0D
Language
English
~XX70 2
7E 30 30 37 30 20 32 0D
German
~XX70 3
7E 30 30 37 30 20 33 0D
French
~XX70 4
7E 30 30 37 30 20 34 0D
Italian
~XX70 5
7E 30 30 37 30 20 35 0D
Spanish
~XX70 6
7E 30 30 37 30 20 36 0D
Portuguese
~XX70 7
7E 30 30 37 30 20 37 0D
Polish
~XX70 8
7E 30 30 37 30 20 38 0D
Dutch
~XX70 9
7E 30 30 37 30 20 39 0D
Swedish
~XX70 10
7E 30 30 37 30 20 31 30 0D
Norwegian/Danish
~XX70 11
7E 30 30 37 30 20 31 31 0D
Finnish
~XX70 12
7E 30 30 37 30 20 31 32 0D
Greek
~XX70 13
7E 30 30 37 30 20 31 33 0D
Traditional Chinese
~XX70 14
7E 30 30 37 30 20 31 34 0D
Simplified Chinese
~XX70 15
7E 30 30 37 30 20 31 35 0D
Japanese
~XX70 16
7E 30 30 37 30 20 31 36 0D
Korean
~XX70 17
7E 30 30 37 30 20 31 37 0D
Russian
~XX70 18
7E 30 30 37 30 20 31 38 0D
Hungarian
~XX70 19
7E 30 30 37 30 20 31 39 0D
Czechoslovak
~XX70 20
7E 30 30 37 30 20 32 30 0D
Arabic
~XX70 21
7E 30 30 37 30 20 32 31 0D
Thai
~XX70 22
7E 30 30 37 30 20 32 32 0D
Turkish
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX71 1
7E 30 30 37 31 20 31 0D
Projection
Front-Desktop
~XX71 2
7E 30 30 37 31 20 32 0D
Rear-Desktop
~XX71 3
7E 30 30 37 31 20 33 0D
Front-Ceiling
~XX71 4
7E 30 30 37 31 20 34 0D
Rear-Ceiling
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX72 1
7E 30 30 37 32 20 31 0D
Menu Location
Top Left
~XX72 2
7E 30 30 37 32 20 32 0D
Top Right
~XX72 3
7E 30 30 37 32 20 33 0D
Centre
~XX72 4
7E 30 30 37 32 20 34 0D
Bottom Left
~XX72 5
7E 30 30 37 32 20 35 0D
Bottom Right
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX73 n
7E 30 30 37 33 20 a 0D
Signal
Frequency
n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX91 n
7E 30 30 39 31 20 a 0D
Automatic
n = 0 disable; n = 1 enable
~XX74 n
7E 30 30 37 34 20 a 0D
Phase
n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n
7E 30 30 37 35 20 a 0D
H. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n
7E 30 30 37 36 20 a 0D
V. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX77 n
7E 30 30 37 37 20 aabbcc 0D Security
Security Timer
Month/Day/Hour
n = mm/dd/hh
mm= 00 (aa=30 30) ~ 12 (aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=33 30)
hh= 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1
7E 30 30 37 38 20 31 0D
Security Settings
Enable
~XX78 0
7E 30 30 37 38 20 32 0D
Disable(0/2 for backward compatible)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX79 n
7E 30 30 37 39 20 a 0D
Projector ID
n = 00 (a=30 30) ~ 99 (a=39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX80 1
7E 30 30 38 30 20 31 0D
Mute
On
~XX80 0
7E 30 30 38 30 20 30 0D
Off (0/2 for backward compatible)
~XX81 n
7E 30 30 38 31 20 a 0D
Volume
n = 0 (a=30) ~ 10 (a=31 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX82 1
7E 30 30 38 32 20 31 0D
Logo
Optoma
~XX82 3
7E 30 30 38 32 20 32 0D
Netural
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX100 1
7E 30 30 31 30 30 20 31 0D
Source Lock
On
~XX100 0
7E 30 30 31 30 30 20 30 0D
Off (0/2 for backward compatible)
~XX100 3
7E 30 30 31 30 30 20 33 0D
Next Source
~XX101 1
7E 30 30 31 30 31 20 31 0D
High Altitude
On
~XX101 0
7E 30 30 31 30 31 20 30 0D
Off (0/2 for backward compatible)
~XX102 1
7E 30 30 31 30 32 20 31 0D
Information Hide
On
~XX102 0
7E 30 30 31 30 32 20 30 0D
Off (0/2 for backward compatible)
~XX103 1
7E 30 30 31 30 33 20 31 0D
Keypad Lock
On
~XX103 0
7E 30 30 31 30 33 20 30 0D
Off (0/2 for backward compatible)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX104 1
7E 30 30 31 30 34 20 31 0D
Background Color
Blue
~XX104 2
7E 30 30 31 30 34 20 32 0D
Black
~XX104 3
7E 30 30 31 30 34 20 33 0D
Red
~XX104 4
7E 30 30 31 30 34 20 34 0D
Green
~XX104 5
7E 30 30 31 30 34 20 35 0D
White
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ʳ
~XX105 1
7E 30 30 31 30 35 20 31 0D
Advanced
Direct Power On
On
~XX105 0
7E 30 30 31 30 35 20 30 0D
Off (0/2 for backward compatible)
~XX106 n
7E 30 30 31 30 36 20 a 0D
Auto Power Off (min)
n = 0 (a=30) ~ 180 (a=31 38 30) step:5
~XX107 n
7E 30 30 31 30 37 20 a 0D
Sleep Timer (min)
n = 0 (a=30) ~ 995 (a=39 39 39) step:5
~XX114 1
7E 30 30 31 31 34 20 31 0D
Eco Standby(1W)
On
~XX114 0
7E 30 30 31 31 34 20 30 0D
Off (0/2 for backward compatible)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX109 1
7E 30 30 31 30 39 20 31 0D
Lamp Reminder
On
~XX109 0
7E 30 30 31 30 39 20 30 0D
Off (0/2 for backward compatible)
~XX110 1
7E 30 30 31 31 30 20 31 0D
Brightness Mode
Bright
~XX110 0
7E 30 30 31 31 30 20 30 0D
STD (0/2 for backward compatible)
~XX111 1
7E 30 30 31 31 31 20 31 0D
Lamp Reset
Yes
~XX111 0
7E 30 30 31 31 31 20 30 0D
No (0/2 for backward compatible)
English
46
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX112 1
7E 30 30 31 31 32 20 31 0D
Reset
Yes
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX99 1
7E 30 30 39 39 20 31 0D
RS232 Alert Reset
Reset System Alert
~XX210 n
7E 30 30 32 30 30 20 n 0D
Display message on the OSD
n: 1-30 characters
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to emulate Remote
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX140 1
7E 30 30 31 34 30 20 31 0D
Power
~XX140 10
7E 30 30 31 34 30 20 31 30 0D
Up/Page +
~XX140 11
7E 30 30 31 34 30 20 31 31 0D
Left/Source
~XX140 12
7E 30 30 31 34 30 20 31 32 0D
Enter (for projection MENU)
~XX140 13
7E 30 30 31 34 30 20 31 33 0D
Right/Re-SYNC
~XX140 14
7E 30 30 31 34 30 20 31 34 0D
Down/Page ~XX140 15
7E 30 30 31 34 30 20 31 35 0D
Keystone +
~XX140 16
7E 30 30 31 34 30 20 31 36 0D
Keystone ~XX140 17
7E 30 30 31 34 30 20 31 37 0D
Volume ~XX140 18
7E 30 30 31 34 30 20 31 38 0D
Volume +
~XX140 19
7E 30 30 31 34 30 20 31 39 0D
Brightness (1)
~XX140 20
7E 30 30 31 34 30 20 32 30 0D
Menu (2)
~XX140 21
7E 30 30 31 34 30 20 32 31 0D
Zoom (3)
~XX140 22
7E 30 30 31 34 30 20 32 32 0D
Contrast (4)
~XX140 23
7E 30 30 31 34 30 20 32 33 0D
Freeze (5)
~XX140 24
7E 30 30 31 34 30 20 32 34 0D
AV Mute (6)
~XX140 25
7E 30 30 31 34 30 20 32 35 0D
S-Video (7)
~XX140 26
7E 30 30 31 34 30 20 32 36 0D
VGA1 toggle (8)
~XX140 27
7E 30 30 31 34 30 20 32 37 0D
Video (9)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND from projector automatically
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code
HEX Code
Function
Projector Return
Description
232 ASCII Code
HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------when Standby/Warming/Cooling/Out of Range/
INFOn
n : 0/1/2/3/4/6/7/8/9 = Standby/Warming/Cooling/Out of Range/
Lamp fail/Fan Lock/Over Temperature/Lamp Hours Running Out/
Lamp fail/Fan Lock/Over Temperature/Lamp Hours Running Out/
Cover Open
Cover Open
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------READ from projector
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX121 1
7E 30 30 31 32 31 20 31 0D
Input Source Commands
OKn
n : 0/1/3/4/ = None/VGA1/S-Video/Video/
~XX122 1
7E 30 30 31 32 32 20 31 0D
Sofware Version
OKdddd
dddd: FW version
~XX123 1
7E 30 30 31 32 33 20 31 0D
Display Mode
OKn
n : 0/1/2/3/4/5/6/7/8 = None/Presentation/Bright/Movie/sRGB/User1/
User2/Blackboard/Classroom/
~XX124 1
7E 30 30 31 32 34 20 31 0D
Power State
OKn
n : 0/1 = Off/On
~XX125 1
7E 30 30 31 32 35 20 31 0D
Brightness
OKn
~XX126 1
7E 30 30 31 32 36 20 31 0D
Contrast
OKn
~XX127 1
7E 30 30 31 32 37 20 31 0D
Aspect Ratio
OKn
n : 0/1/2/3/4 = 4:3/16:9-l/16:9-ll/Native/AUTO
~XX128 1
7E 30 30 31 32 38 20 31 0D
Color Temperature
OKn
n : 0/1/2 = Warm/Medium/Cold
~XX129 1
7E 30 30 31 32 39 20 31 0D
Projection Mode
OKn
n : 0/1/2/3 = Front-Desktop/ Rear-Desktop/ Front-Ceiling/ Rear-Ceiling
~XX150 1
7E 30 30 31 35 30 20 31 0D
Information
OKabbbbccdddde
a : 0/1 = Off/On
bbbb: LampHour
cc: source 00/01/03/04 = None/VGA1/S-Video/Video
dddd: FW version
e : Display mode 0/1/2/3/4/5/6/7/8/
None/Presentation/Bright/Movie/sRGB/User1/User2/
Blackboard/Classroom
~XX151 1
7E 30 30 31 35 31 20 31 0D
Model name
OKn
n:1 =SVGA
~XX108 1
7E 30 30 31 30 38 20 31 0D
Lamp Hours
OKbbbb
bbbb: LampHour
~XX108 2
7E 30 30 31 30 38 20 31 0D
Cumulative Lamp Hours
OKbbbbb
bbbbb: (5 digits) Total Lamp Hours
47
English
Appendices
Ceiling Mount Installation
1. To prevent damage to your projector, please use the
Optoma ceiling mount.
2. If you wish to use a third party ceiling mount kit, please
ensure the screws used to attach a mount to the projector
meet the following specifications:
97.00
84.00
Warning:
1. If you buy a ceiling
mount from another
company, please
be sure to use the
correct screw size.
Screw size will vary
depending on the
thickness of the
mounting plate.
2. Be sure to keep
at least 10 cm gap
between the ceiling
and the bottom of the
projector.
3. Avoid installing the
projector near a heat
source.
110.00
77.75
192.00
55.00
82.30
Please note that
damage resulting
from incorrect
installation will
invalidate the
warranty.
Screw type: M3*3
Maximum screw length: 10mm
Minimum screw length: 7.5mm
Lens
63.00
118.65
167.66
286.31
English
48
Unit: mm
Appendices
Optoma Global Offices
For service or support please contact your local office.
USA
715 Sycamore Drive Milpitas, CA 95035, USA www.optomausa.com
Tel : 408-383-3700
Fax: 408-383-3702
Service : services@optoma.com
Canada
5630 Kennedy Road, Mississauga, Tel : 905-361-2582
ON, L4Z 2A9, Canada Fax: 905-361-2581
www.optoma.ca
Service : canadacsragent@optoma.com
Europe
42 Caxton Way, The Watford Business Park
Watford, Hertfordshire,
WD18 8QZ, UK
Tel : +44 (0) 1923 691 800
www.optoma.eu Fax: +44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865 Service : service@tsc-europe.com
France
Bâtiment E Tel : +33 1 41 46 12 20
81-83 avenue Edouard Vaillant Fax: +33 1 41 46 94 35
92100 Boulogne Billancourt, France Service : savoptoma@optoma.fr
Spain
C/ José Hierro,36 Of. 1C 28529 Rivas VaciaMadrid,
Spain Deutschland
Werftstrasse 25 D40549 Düsseldorf, Germany Scandinavia
Lerpeveien 25 3040 Drammen Norway Tel : +34 91 499 06 06
Fax: +34 91 670 08 32
Tel : +49 (0) 211 506 6670
Fax: +49 (0) 211 506 66799
Service : info@optoma.de
Tel : +47 32 98 89 90
Fax: +47 32 98 89 99
Service : info@optoma.no
PO.BOX 9515
3038 Drammen
Norway
49
English
Appendices
Latin America
715 Sycamore Drive Milpitas, CA 95035, USA
www.optoma.com.br
Tel : 408-383-3700
Fax: 408-383-3702
www.optoma.com.mx
Korea
WOOMI TECH.CO.,LTD.
4F,Minu Bldg.33-14, Kangnam-Ku, Tel : +82+2+34430004
seoul,135-815, KOREA
Fax: +82+2+34430005
Japan
東京都足立区綾瀬3-25-18
株式会社オーエスエム
サポートセンター:0120-46-5040
Taiwan
5F., No. 108, Minchiuan Rd. Shindian City, Taipei Taiwan 231, R.O.C.
www.optoma.com.tw
E-mail : info@osscreen.com
www.os-worldwide.com
Tel : +886-2-2218-2360
Fax: +886-2-2218-2313
Service : services@optoma.com.tw
asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street,
Cheung Sha Wan, Kowloon, Hong Kong China
5F, No. 1205, Kaixuan Rd., Changning District Shanghai, 200052, China
English
50
Tel : +852-2396-8968
Fax: +852-2370-1222
www.optoma.com.hk
Tel : +86-21-62947376
Fax: +86-21-62947375
www.optoma.com.cn
Appendices
Regulation & Safety notices
This appendix lists the general notices of your projector.
FCC notice
This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can
be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modifications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to
operate this projector.
51
English
Appendices
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1.This device may not cause harmful interference and
2.This device must accept any interference received,
including interference that may cause undesired
operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numerique de la classe B est conforme a la
norme NMB-003 du Canada.
Declaration of Conformity for EU
countries
• EMC Directive 2004/108/EC (including amendments)
• Low Voltage Directive 2006/95/EC
• R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.
English
52
Download PDF
Similar pages