User Guide
DSL-AC55U
Wireless-AC1200
Dual-band 802.11ac VDSL/ADSL
Modem Router
Wi-Fi
ADS
Dua
L / VDS
l Ban
L Mod
d
em 802.11a
Rou
ter c
E11623
First Edition
April 2016
Copyright © 2016 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described
in it, may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language in any form or by any means, except
documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired,
modified or altered, unless such repair, modification of alteration is authorized
in writing by ASUS; or (2) the serial number of the product is defaced or
missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS,
EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS
AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR
PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE
FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE
AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A
COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY
FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be
registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent
to infringe.
2
Table of contents
1
Getting to know your xDSL modem router
1.1Welcome!.........................................................................................6
1.2
Package contents..........................................................................6
1.3
Your xDSL modem router...........................................................7
1.4
Positioning your xDSL modem router...................................9
1.5
Setup Requirements................................................................. 10
1.6
xDSL Modem Router Setup.................................................... 11
1.6.1 Wired connection...................................................................11
1.6.2 Wireless connection..............................................................12
2
Getting started
3
Configuring the General settings
2.1
2.2
2.3
3.1
Logging into the Web GUI...................................................... 13
Quick Internet Setup (QIS) Wizard with Auto-detection.14
Connecting to your wireless network................................. 18
Using the Network Map .......................................................... 19
3.1.1 Setting up the wireless security settings.......................20
3.1.2 Managing your network clients........................................21
3.1.3 Monitoring your USB device..............................................22
3.2
3.3
Creating a Guest Network....................................................... 25
Using the Traffic Manager....................................................... 27
3.3.1 Managing QoS (Quality of Service) Bandwidth..........27
3.3.2 Monitoring Traffic ..................................................................30
3.3.3Spectrum ..................................................................................31
3.4
3.5
Setting up Parental Control.................................................... 32
Using the USB Application...................................................... 33
3.5.1 Using AiDisk................................................................................33
3.5.2 Using Servers Center.............................................................35
3
Table of contents
3.6
Using AiCloud.............................................................................. 40
3.6.1 Cloud Disk.................................................................................41
3.6.2 Smart Access............................................................................43
3.6.3 Smart Sync................................................................................44
4
Configuring the Advanced Settings
4.1Wireless.......................................................................................... 45
4.1.1General.......................................................................................45
4.1.2WPS.............................................................................................48
4.1.3Bridge.........................................................................................50
4.1.4 Wireless MAC Filter................................................................52
4.1.5 RADIUS Setting.......................................................................53
4.1.6Professional..............................................................................54
4.2LAN.................................................................................................. 56
4.2.1 LAN IP.........................................................................................56
4.2.2 DHCP Server.............................................................................57
4.2.3Route..........................................................................................59
4.2.4IPTV.............................................................................................60
4.3WAN................................................................................................ 61
4.3.1 Internet Connection..............................................................61
4.3.2 Dual WAN..................................................................................63
4.3.3 Port Trigger...............................................................................64
4.3.4 Virtual Server/Port Forwarding.........................................66
4.3.5DMZ............................................................................................69
4.3.6DDNS..........................................................................................70
4.3.7 NAT Passthrough....................................................................71
4.4IPv6.................................................................................................. 72
4.5
VPN Server.................................................................................... 73
4.6Firewall........................................................................................... 74
4.6.1General.......................................................................................74
4
Table of contents
4.6.2 URL Filter...................................................................................75
4.6.3 Keyword Filter.........................................................................76
4.6.4 Network Services Filter........................................................77
4.7Administration............................................................................ 78
4.7.1System........................................................................................78
4.7.2 Firmware Upgrade.................................................................79
4.7.3 Restore/Save/Upload Setting............................................80
4.7.4 DSL Setting...............................................................................81
4.7.5Feedback...................................................................................84
4.8
System Log................................................................................... 85
5Utilities
5.1
5.2
5.3
Device Discovery........................................................................ 86
Firmware Restoration............................................................... 87
Setting up your printer server............................................... 88
5.3.1 ASUS EZ Printer Sharing......................................................88
5.3.2 Using LPR to Share Printer..................................................92
5.4
Download Master....................................................................... 97
5.4.1 Configuring Bit Torrent download settings..................98
5.4.2 NZB settings.............................................................................99
6Troubleshooting
6.1
6.2
Basic Troubleshooting............................................................100
Frequently Asked Questions (FAQs) .................................103
Appendices
Notices ......................................................................................................112
ASUS Contact information...................................................................126
Networks Global Hotline Information.............................................127
5
1
Getting to know your xDSL
modem router
1.1Welcome!
Thank you for purchasing an ASUS DSL-AC55U Wireless VDSL/
ADSL Modem Router!
The ultra-thin and stylish DSL-AC55U features 2.4GHz and 5GHz
dual bands for an unmatched concurrent wireless HD streaming;
operates as a router on an ADSL or VDSL line; SMB server, UPnP
AV server, and FTP server for 24/7 file sharing; and capability to
handle 300,000 sessions. These features make this xDSL modem
router a good choice for complete home networking.
1.2 Package contents
VDSL/ADSL Wireless Modem Router
Network cable (RJ-45 cable)
Support CD (Manual, utility software)
Splitter (varies with region)
Power adapter
Quick Start Guide
DSL/phone cable (RJ-11 cable)
Warranty card
NOTES:
• If any of the items are damaged or missing, contact ASUS for
technical inquiries and support. Refer to the ASUS Support Hotline
list at the back of this user manual.
• Keep the original packaging material in case you would need future
warranty services such as repair or replacement.
6
1.3 Your xDSL modem router
Wi-F
i ADS
Dua
L / VDS
l Ban
L Mod
d
em 802.11a
Rou
ter c
DSL
E-WAN
WPS
Wi-Fi on/off
Power LED
Off: No power.
On: Device is ready.
Flashing slow: Rescue mode
Flashing quick: WPS is processing.
DSL LED
Off: No DSL link or unable to establish DSL link.
On: DSL link is established.
Flashing: DSL is attempting to connect to a DSLAM.
Ethernet WAN LED
Off: No power or no physical connection.
On: Has physical connection to a wide area network (WAN).
Internet LED
Off: No power or no Internet connection.
On: Internet connection is established.
LAN 1~4 LED
Off: No power or no physical connection.
On: Has physical connection to an Ethernet network.
2.4GHz LED
Off: No 2.4GHz signal.
On: Wireless system is ready.
Flashing: Transmitting or receiving data via wireless connection.
5GHz LED
Off: No 5GHz signal.
On: Wireless system is ready.
Flashing: Transmitting or receiving data via wireless connection.
7
USB LED
Off: No power or no physical connection.
On: Has physical connection to USB devices.
DSL port
Connect to a splitter or to a telephone outlet via an RJ-11 cable.
LAN 1 ~ 4 ports
Connect network cables into these ports to establish LAN connection.
Ethernet WAN port
Connect a network cable into this port to establish WAN connection.
Reset button
This button resets or restores the system to its factory default settings.
USB 2.0 port
Insert USB 2.0 devices such as USB hard disks or USB flash drives into this
port.
Power button
Press this button to power on or off the system.
Power (DC-IN) port
Insert the bundled AC adapter into this port and connect your router to a
power source.
WPS and Wi-Fi on/off button
Press this button to turn on/off the Wi-Fi connection.
Press this button to launch the WPS Wizard.
NOTES:
• Use only the adapter that came with your package. Using other
adapters may damage the device.
• Specifications:
• Power consumption in off mode: 0.21W
• Power consumption in network standby mode: 4.21W
• The average power consumption is determined at room
temperatures with the following load:
8
DC Power adapter
DC Output: +
12V with max. 2A current
Operating
Temperature
0~40oC
Storage
0~70oC
Operating Humidity
50~90%
Storage
20~90%
1.4 Positioning your xDSL modem router
For the best wireless signal transmission between the xDSL
modem router and the network devices connected to it, ensure
that you:
•
•
•
•
•
Place the xDSL modem router in a centralized area for a
maximum wireless coverage for the network devices.
Keep the device away from metal obstructions and away from
direct sunlight.
To prevent signal interference or loss, keep the device away
from 802.11g or 20MHz only Wi-Fi devices, 2.4GHz computer
peripherals, Bluetooth devices, cordless phones, transformers,
heavy-duty motors, fluorescent lights, microwave ovens,
refrigerators, and other industrial equipment.
Always update to the latest firmware. Visit the ASUS
website at http://www.asus.com to get the latest firmware
updates.
To ensure the best wireless signal, orient the four
detachable antennas as shown in the drawing below.
90°
90°
9
1.5 Setup Requirements
To set up your wireless network, you need a computer that meets
the following system requirements:
• Ethernet RJ-45 (LAN) port (10Base-T/100Base-TX/1000BaseTX)
• IEEE 802.11a/b/g/n/ac wireless capability
• An installed TCP/IP service
• Web browser such as Internet Explorer, Firefox, Safari, or
Google Chrome
NOTES:
• If your computer does not have built-in wireless capabilities, you may
install an IEEE 802.11a/b/g/n/ac WLAN adapter to your computer to
connect to the network.
• With its dual band technology, your ADSL/VDSL router supports
2.4GHz and 5GHz wireless signals simultaneously. This allows you
to browse the Internet or access e-mail messages using the 2.4GHz
band while streaming high-definition audio/video files such as
movies or music using the 5GHz band.
• If you are using only one computer with a single band IEEE 802.11a/
b/g/n/ac WLAN adapter, you will only be able to use the 2.4GHz
band.
• If you are using only one computer with a dual band IEEE 802.11a/
b/g/n/ac WLAN adapter, you will be able to use the 2.4GHz or 5GHz
band.
• If you are using two computers with both IEEE 802.11a/b/g/n/ac
WLAN adapters, you will be able to use both 2.4GHz and 5GHz bands
simultaneously.
• The Ethernet RJ-45 cables that will be used to connect the network
devices should not exceed 100 meters.
10
1.6 xDSL Modem Router Setup
IMPORTANT!
• Use a wired connection when setting up your xDSL modem router to
avoid possible setup problems.
• Before setting up your ASUS xDSL modem router, do the following:
• If you are replacing an existing xDSL modem router, disconnect it
from your network.
1.6.1Wired connection
NOTE:You can use either a straight-through cable or a crossover cable
for wired connection.
Wall power outlet
DSL
E-WAN
WPS
Wi-Fi on/off
Power
DSL
Splitter
Phone
LAN
Wall telephone outlet
Computer
To set up your xDSL modem router via wired connection:
1. Insert your xDSL modem router’s power adapter to the DC-IN
port and plug it to a power outlet.
2. Connect one end of the RJ-11 cable to the DSL port of your
xDSL modem router, and connect the other end to the DSL
port of your splitter.
3. Using a network cable, connect your computer to your xDSL
modem router’s LAN port.
IMPORTANT! After turning on your xDSL modem router, wait for about
two to three minutes for it to boot up.
11
1.6.2Wireless connection
Wall power outlet
DSL
E-WAN
WPS
Wi-Fi on/off
Power
DSL
Computer
Phone
Splitter
Wall telephone outlet
To set up your xDSL modem router via wireless connection:
1. Insert your xDSL modem router’s power adapter to the DC-IN
port and plug it to a power outlet.
2. Connect one end of the RJ-11 cable to the DSL port of your
xDSL modem router, and connect the other end to the DSL
port of your splitter.
3. Install an IEEE 802.11a/b/g/n/ac WLAN adapter on your
computer.
NOTES:
• For details on connecting to a wireless network, refer to the WLAN
adapter’s user manual.
• To set up the security settings for your network, refer to the section
Setting up the wireless security settings in Chapter 3 of this user
manual.
12
2
Getting started
2.1 Logging into the Web GUI
Your ASUS Wireless xDSL Modem Router comes with an intuitive
web graphical user interface (GUI) that allows you to easily
configure its various features through a web browser such as
Internet Explorer, Firefox, Safari, or Google Chrome.
NOTE: The features may vary with different firmware versions.
To log into the web GUI:
1. On your web browser, manually key in the xDSL modem
router’s default IP address: http://router.asus.com
2. On the login page, key in the default user name (admin) and
password (admin).
3. You can now use the Web GUI to configure various settings of
your ASUS XDSL modem router.
Top command buttons
Information
banner
QIS
Navigation
panel
right column
middle
column
NOTE:If you are logging into the Web GUI for the first time, you will be
directed to the Quick Internet Setup (QIS) page automatically.
13
2.2 Quick Internet Setup (QIS) Wizard with
Auto-detection
The Quick Internet Setup (QIS) function guides you in quickly
setting up your Internet connection.
NOTE: When setting the Internet connection for the first time, press the
Reset button on your xDSL modem router to reset it to its factory default
settings. For more details, refer to the section Firmware Restoration in
Chapter 5 of this user manual.
To use QIS with auto-detection:
1. Log into the Web GUI. The QIS page launches automatically.
NOTES:
• By default, the login username and password for your xDSL modem
router's Web GUI is admin. For details on changing your xDSL
modem router's login username and password, refer to section 4.7.1
System.
• The xDSL modem router's login username and password allows you
to log into your xDSL modem router's Web GUI to configure your
xDSL modem router's settings. The network name (SSID) and security
key allows Wi-Fi devices to log in and connect to your wireless
network.
14
2. Your xDSL modem router automatically configures the DSL
Annex mode, Internet connection type, and VPI/VCI value
and encapsulation modes. Key in the Internet account
information from your Internet Service Provider (ISP).
IMPORTANT! Obtain the necessary information from your ISP to
configure the Internet connection.
NOTES:
• The auto-detection of your ISP connection type takes place when
you configure your xDSL modem router for the first time or when
your device is reset to its default settings.
• By default, the QIS Wizard is for DSL setup. If you want to configure
DSL-AC55U as a wireless router, refer to the section Internet
Connection in Chapter 4 of this user manual.
15
3. If QIS failed to detect your Internet connection type, follow
the steps below to manually configure your connection
settings:
a) Select the Annex mode that your DSL service uses.
NOTES:
• Annex A or Annex B mode has multiple modes: Annex A/I/J/L/M
or Annex B/J. If your ISP DSLAM offers both Annex A and Annex M
mode, QIS automatically set the Annex mode to Annex A/I/J/L/M
mode and completes the DSL line setting.
• If you want to configure your ASUS xDSL modem router to a specific
Annex mode, refer to the section DSL Setting in Chapter 4 of this
user guide.
16
b) Select your Country and Internet Service Provider (ISP).
c)Assign the wireless network name (SSID) and security key
for your wireless connection. Click Apply when done.
17
d)A summary page appears to show the current settings for
your network. Click Next to save your network settings
and go to the Network Map page.
2.3 Connecting to your wireless network
After setting up your xDSL modem router via QIS, you can connect
your computer or other smart devices to your wireless network.
To connect to your network:
1. On your computer, click the network icon in the
notification area to display the available wireless networks.
2. Select the wireless network that you want to connect to, then
click Connect.
3. You may need to key in the network security key for a secured
wireless network, then click OK.
4. Wait while your computer establishes connection to the
wireless network successfully. The connection status is
displayed and the network icon displays the connected
status.
18
NOTES:
• Refer to the next chapters for more details on configuring your
wireless network's settings.
• Refer to your device's user manual for more details on connecting it
to your wireless network.
3
Configuring the General
settings
3.1 Using the Network Map
Network Map allows you to configure your network’s security
settings, manage your network clients, and monitor your USB
device.
19
3.1.1Setting up the wireless security settings
To protect your wireless network from unauthorized access, you
need to configure its security settings.
To set up the wireless security settings:
1. From the navigation panel, go to General > Network Map.
2. On the Network Map screen and under System status, you
can configure the wireless security settings such as SSID,
security level, and encryption settings.
NOTE:You can set up different wireless security settings for 2.4GHz and
5GHz bands.
2.4GHz security settings
5GHz security settings
3. On the Wireless name (SSID) field, key in a unique name for
your wireless network.
4. From the Authentication Method dropdown list, select the
encryption method for your wireless network.
20
IMPORTANT! The IEEE 802.11n/ac standard prohibits using High
Throughput with WEP or WPA-TKIP as the unicast cipher. If you use these
encryption methods, your data rate will drop to IEEE 802.11g 54Mbps
connection.
5. Key in your WPA-PSK key (security passkey).
6.Click Apply when done.
3.1.2Managing your network clients
To manage your network clients:
1. From the navigation panel, go to General > Network Map
tab.
2. On the Network Map screen, select the Client Status icon to
display your network client’s information.
21
3.1.3Monitoring your USB device
ASUS DSL-AC55U provides two USB 2.0 ports for connecting USB
devices or USB printer to allow you to share files and printer with
clients in your network.
NOTES:
• USB External HDD/Flash disk:
22
• Your xDSL modem router works with most USB HDDs/Flash disks
up to 3TB and supports read-write access for FAT16, FAT32, EXT2,
EXT3, and NTFS.
• To safely remove the USB disk, go to the Network Map page’s
upper right corner, click the USB icon and click Eject USB disk.
• For the list of file system and hard disk partitions that your xDSL
modem router supports, visit http://event.asus.com/networks/
disksupport
NOTES:
• Network Printer Server:
• Network printer utility is supported on Windows®XP/Vista/7/8/8.1.
To install the utility on Mac OS, please go to USB Application >
Network Printer Server, click Download Now!, then select Use
LPR protocol for sharing.
• For the list of printers that your xDSL modem router supports,
visit http://event.asus.com/networks/printersupport
IMPORTANT! You first need to create a share account and its
permission /access rights to allow other network clients to access the
USB device via an FTP site/third-party FTP client utility, Servers Center,
Samba, or AiCloud. For more details, refer to the section 3.5 Using the
USB Application and 3.6 Using AiCloud in this user manual.
To monitor your USB device:
1. From the navigation panel, go to General > Network Map.
2. On the Network Map screen, select the USB Disk Status icon
to display your USB device’s information.
3. On the AiDisk Wizard field, click GO to set up an FTP server for
Internet file sharing.
NOTES:
• For more details, refer to the section 3.5.2 Using Servers Center in
this user manual.
• The xDSL modem router works with most USB HDDs/Flash disks (up
to 3TB size) and supports read-write access for FAT16, FAT32, EXT2,
EXT3, and NTFS.
23
Safely removing the USB disk
IMPORTANT: Incorrect removal of the USB disk may cause data
corruption.
To safely remove the USB disk:
1. From the navigation panel, go to General > Network Map.
2. In the upper right corner, click
> Eject USB disk. When
the USB disk is ejected successfully, the USB status shows
Unmounted.
24
3.2 Creating a Guest Network
The Guest Network provides temporary visitors with Internet
connectivity via access to separate SSIDs or networks without
providing access to your private network.
NOTE:ASUS DSL-AC55U supports up to four SSIDs (including the main
SSID).
To create a guest network:
1. From the navigation panel, go to General > Guest Network.
2. On the Guest Network screen, select 2.4GHz or 5GHz
frequency band for the guest network that you want to create.
3.Click Enable.
25
4. To configure additional options, click the network name (SSID)
that you want to modify.
5. Assign a wireless name for your temporary network on the
Network Name (SSID) field.
6. Select an Authentication Method.
7. Specify the Access time or choose Limitless.
8.Select Disable or Enable on the Access Intranet item.
9. When done, click Apply.
26
3.3 Using the Traffic Manager
3.3.1Managing QoS (Quality of Service) Bandwidth
Quality of Service (QoS) allows you to set the bandwidth priority
and manage network traffic.
To set up bandwidth priority:
1. From the navigation panel, go to General > Traffic Manager
> QoS tab.
2.Click ON to enable QoS. Fill in the upload and download
bandwidth fields.
NOTE: Get the bandwidth information from your ISP.
3.Click Save.
NOTE: The User Specify Rule List is for advanced settings. If you want
to prioritize specific network applications and network services, select
User-defined QoS rules or User-defined Priority from the drop-down
list on the upper-right corner.
27
4. On the user-defined QoS rules page, there are four default
online service types – web surf, HTTPS and file transfers.
Select your preferred service, fill in the Source IP or MAC,
Destination Port, Protocol, Transferred and Priority, then
click Apply. The information will be configured in the QoS
rules screen.
NOTES
• To fill in the source IP or MAC, you can:
a)
Enter a specific IP address, such as "192.168.122.1".
b)Enter IP addresses within one subnet or within the same IP
pool, such as “192.168.123.*”, or “192.168.*.*”
c)
d)The format for the MAC address is six groups of two
hexadecimal digits, separated by colons (:), in transmission
order (e.g. 12:34:56:aa:bc:ef)
Enter all IP addresses as “*.*.*.*” or leave the field blank.
NOTES:
• For source or destination port range, you can either:
a)
Enter a specific port, such as “95”.
b)Enter ports within a range, such as “103:315”, “>100”, or
“<65535”.
• The Transferred column contains information about the upstream
and downstream traffic (outgoing and incoming network traffic) for
one section. In this column, you can set the network traffic limit (in
KB) for a specific service to generate specific priorities for the service
assigned to a specific port. For example, if two network clients, PC
1 and PC 2, are both accessing the Internet (set at port 80), but PC 1
exceeds the network traffic limit due to some downloading tasks, PC
1 will have a lower priority. If you do not want to set the traffic limit,
leave it blank.
28
5. On the User-defined Priority page, you can prioritize the
network applications or devices into five levels from the userdefined QoS rules’ dropdown list. Based on priority level, you
can use the following methods to send data packets:
• Change the order of upstream network packets that are sent
to the Internet.
• Under Upload Bandwidth table, set Minimum Reserved
Bandwidth and Maximum Bandwidth Limit for multiple
network applications with different priority levels. The
percentages indicate the upload bandwidth rates that are
available for specified network applications.
NOTES:
• Low-priority packets are disregarded to ensure the transmission of
high-priority packets.
• Under Download Bandwidth table, set Maximum Bandwidth Limit
for multiple network applications in corresponding order. The higher
priority upstream packet will cause the higher priority downstream
packet.
• If there are no packets being sent from high-priority applications, the
full transmission rate of the Internet connection is available for lowpriority packets.
6. Set the highest priority packet. To ensure a smooth online
gaming experience, you can set ACK, SYN, and ICMP as the
highest priority packet.
NOTE: Ensure to enable QoS first and set up the upload and download
rate limits.
29
3.3.2 Monitoring Traffic
The traffic monitor function allows you to access the bandwidth
usage and speed of your Internet, wired, and wireless networks. It
allows you to monitor network traffic even on a daily basis.
NOTE: Packets from the Internet are evenly transmitted to the wired
and wireless devices.
30
3.3.3Spectrum
DSL Spectrum provide information on the connection quality. The
graph to signal-to-noise ratio shows the classic SNR (Signal-toNoise Ratio), which can be useful in identifying the stability of the
DSL connection. Transmission/Reception graph shows how many
bits per carrier are transmitted/received.
31
3.4 Setting up Parental Control
Parental Control allows you to control the Internet access time.
Users can set the time limit for a client’s network usage.
To use the parental control function:
1. From the navigation panel, go to General > Parental control.
2.Click Enable to activate Parental Control.
3. Select the client whose network usage you want to control.
You may also key in the client’s MAC address in the Client
MAC Address column.
NOTE: Ensure that the client name does not contain special characters
or spaces as this may cause the router to function abnormally.
4.Click
32
or
to add or delete the client’s profile.
3.5 Using the USB Application
The USB Applications function provides AiDisk, Servers Center,
Media Server, Network Printer Server, and Download Master
submenus.
IMPORTANT! To use the server functions, you need to insert a USB
storage device, such as a USB hard disk or USB flash drive, in the USB 2.0
port on the rear panel of your xDSL modem router. Ensure that the USB
storage device is formatted and partitioned properly. Refer to the ASUS
website at http://event.asus.com/2009/networks/disksupport/ for the
file system support table.
3.5.1 Using AiDisk
AiDisk allows you to share files stored on a connected USB device
through the Internet. AiDisk also assists you with setting up ASUS
DDNS and an FTP server.
To use AiDisk:
1. From the navigation panel, go to General > USB application,
then click the AiDisk icon.
2. From the Welcome to AiDisk wizard screen, click Go.
33
3. Select the access rights that you want to assign to the clients
accessing your shared data.
4. Create your domain name via the ASUS DDNS services, read
the Terms of Service and then select I will use the service
and accept the Terms of service and key in your domain
name. When done, click Next.
You can also select Skip ASUS DDNS settings then click Next
to skip the DDNS setting.
5.Click Finish to complete the setting.
6. To access the FTP site that you created, launch a web browser
or a third-party FTP client utility and key in the ftp link
(ftp://<domain name>.asuscomm.com) you have previously
created.
34
3.5.2Using Servers Center
Servers Center allows you to share the media files from the USB
disk via a Media Server directory, Samba share service, or FTP
share service. You can also configure other settings for the USB
disk in the Servers Center.
Using Media Server
Your xDSL modem router allows DLNA-supported devices to
access multimedia files from the USB disk connected to your xDSL
modem router.
NOTE: Before using the DLNA Media Server function, connect your
device to the DSL-AC55U’s network.
35
To launch the Media Server setting page, go to General > USB
application > Servers Center > Media Servers tab. Refer to the
following for the descriptions of the fields:
• Enable DLNA Media Server: Select ON/OFF to enable/
disable the DLNA Media Server.
• Enable iTunes Server: Select ON/OFF to enable/disable the
iTunes Server.
• Media server directory: Select your media server directory
and click Apply to share files from the USB disk to media
devices in the network.
• Media Server Status: Displays the status of the media server.
Using Network Place (Samba) Share service
Network Place (Samba) Share allows you to set up the accounts
and permissions for the Samba service.
To use Samba share:
1. From the navigation panel, go to General > USB application
> Servers Center.
NOTE: Network Place (Samba) Share is enabled by default.
36
2. Follow the steps below to add, delete, or modify an
account.
To create a new account:
a) Click
to add new account.
b)In the Account and Password fields, key in the name and
password of your network client. Retype the password to
confirm. Click Add to add the account to the list.
To delete an existing account:
a) Select the account that you want to delete.
b)Click .
c)When prompted, click Delete to confirm the account
deletion.
To add a folder:
a) Click .
b)Enter the folder name, and click Add. The folder that you
created will be added to the folder list.
37
3. From the list of folders, select the type of access permission
that you want to assign for specific folders:
• R/W: Select this option to assign read/write access.
• R: Select this option to assign read-only access.
• No: Select this option if you do not want to share a specific
file folder.
4.Click Apply to apply the changes.
Using the FTP Share service
FTP share enables an FTP server to share files from USB disk to
other devices via your local area network or via the Internet.
IMPORTANT:
• Ensure that you safely remove the USB disk. Incorrect removal of the
USB disk may cause data corruption.
• To safely remove the USB disk, refer to the section Safely removing
the USB disk under 3.1.3 Monitoring your USB device.
38
To use FTP Share service:
NOTE: Ensure that you have set up your FTP server through
AiDisk. For more details, refer to the section 3.5.1 Using AiDisk.
1. From the navigation panel, click General > USB application
> Servers Center > FTP Share tab.
2. From the list of folders, select the type of access rights that
you want to assign for specific folders:
• R/W: Select to assign read/write access for a specific folder.
• W: Select to assign write only access for a specific folder.
• R: Select to assign read only access for a specific folder.
• No: Select this option if you do not want to share a specific
folder.
3. Click Apply to confirm the changes.
4. To access the FTP server, key in the ftp link
ftp://<hostname>.asuscomm.com and your user name and
password on a web browser or a third-party FTP utility.
39
3.6 Using AiCloud
AiCloud is a cloud service application that allows you to save, sync,
share, and access your files.
To use AiCloud:
1. From Google Play Store or Apple Store, download and install
the ASUS AiCloud app to your smart device.
2. Connect your smart device to your network. Follow the
instructions to complete the AiCloud setup process.
40
3.6.1Cloud Disk
To create a cloud disk:
1. Insert a USB storage device into the xDSL modem router.
2. Turn on Cloud Disk.
3.Go to https://www.asusnetwork.net and enter the router
login account and password. For better user experience, we
recommend that you use Google Chrome or Firefox.
41
4.You can now start accessing Cloud Disk files on devices
connected to the network.
NOTE: When accessing the devices that are connected to the network,
you need to enter the device’s user name and password manually, which
will not be saved by AiCloud for security reason.
42
3.6.2Smart Access
The Smart Access function allows you to easily access your home
network via your router’s domain name.
NOTES:
• You can create a domain name for your router with ASUS DDNS. For
more details, refer to section 4.3.6 DDNS.
• By default, AiCloud provides a secure HTTPS connection. Key in
https://[yourASUSDDNSname].asuscomm.com for a very secure
Cloud Disk and Smart Access usage.
43
3.6.3Smart Sync
To use Smart Sync:
1. Launch AiCloud, click Smart Sync > Go.
2.Select ON to enable Smart Sync.
3.Click Add new account.
4. Enter your ASUS WebStorage account password and select
the directory that you want to sync with WebStorage.
5.Click Apply.
44
4
Configuring the Advanced
Settings
4.1Wireless
4.1.1General
The General tab allows you to configure the basic wireless
settings.
To configure the basic wireless settings:
1. From the navigation panel, go to Advanced Settings >
Wireless > General tab.
2. Select 2.4GHz or 5GHz as the frequency band for your wireless
network.
3. Assign a unique name containing up to 32 characters for your
SSID (Service Set Identifier) or network name to identify your
wireless network. Wi-Fi devices can identify and connect to
the wireless network via your assigned SSID. The SSIDs on the
information banner are updated once new SSIDs are saved to
the settings.
NOTE: You can assign unique SSIDs for the 2.4 GHz and 5GHz frequency
bands.
45
4. In the Hide SSID field, select Yes to prevent wireless devices
from detecting your SSID. When this function is enabled, you
would need to enter the SSID manually on the wireless device
to access the wireless network.
5. Select any of these wireless mode options to determine
the types of wireless devices that can connect to your xDSL
modem router:
• Auto: Select Auto to allow 802.11ac, 802.11n, 802.11g, and
802.11b devices to connect to the xDSL modem router.
• Legacy: Select Legacy to allow 802.11b/g/n devices to
connect to the xDSL modem router. Hardware that supports
802.11n natively, however, will only run at a maximum speed
of 54Mbps.
• N only: Select N only to maximize wireless N performance.
This setting prevents 802.11g and 802.11b devices from
connecting to the xDSL modem router.
6. Select the operating channel for your xDSL modem router.
Select Auto to allow the xDSL modem router to automatically
select the channel that has the least amount of interference.
7. Select any of these channel bandwidth to accommodate
higher transmission speeds:
40MHz: Select this bandwidth to maximize the wireless
throughput.
20/40MHz: This is the default bandwidth.
20MHz: Select this bandwidth if you encounter some issues
with your wireless connection.
8. Select any of these authentication methods:
• Open System: This option provides no security.
• WPA/WPA2 Personal/WPA Auto-Personal: This option
provides strong security. You can use either WPA (with
TKIP) or WPA2 (with AES). If you select this option, you must
use TKIP + AES encryption and enter the WPA passphrase
(network key).
46
• WPA/WPA2 Enterprise/WPA Auto-Enterprise: This option
provides very strong security. It is with integrated EAP server
or an external RADIUS back-end authentication server.
NOTE: Your xDSL modem router supports the maximum transmission
rate of 54Mbps when the Wireless Mode is set to Auto and encryption
method is WEP or TKIP.
9. Select any of these WEP (Wired Equivalent Privacy) Encryption
options for the data transmitted over your wireless network:
• Off: Disables WEP encryption
• 64-bit: Enables weak WEP encryption
• 128-bit: Enables improved WEP encryption.
10. When done, click Apply.
47
4.1.2WPS
WPS (Wi-Fi Protected Setup) is a wireless security standard that
allows you to easily connect devices to a wireless network. You
can configure the WPS function via the PIN code or WPS button.
NOTE: Ensure that the devices support WPS.
To enable WPS on your wireless network:
1. From the navigation panel, go to Advanced Settings >
Wireless > WPS tab.
2. In the Enable WPS field, move the slider to ON.
3. WPS uses 2.4GHz by default. If you want to change the
frequency to 5GHz, turn OFF the WPS function, click Switch
Frequency in the Current Frequency field, and turn WPS ON
again.
NOTE: WPS supports authentication using Open System, WPA-Personal,
and WPA2-Personal. WPS does not support a wireless network that uses
a Shared Key, WPA-Enterprise, and WPA2-Enterprise encryption method.
48
4. In the WPS Method field, select PBC or PIN Code. If you select
PBC, go to step 5. If you select PIN Code, go to step 6.
5. To set up WPS using the router’s WPS button, follow these
steps:
a.Click Start WPS or press the WPS button found at the rear of
the xDSL modem router.
b.Press the WPS button on your wireless device. This is
normally identified by the WPS logo.
NOTE: Check your wireless device or its user manual for the location of
the WPS button.
c.The xDSL modem router will scan for any available WPS
devices. If the xDSL modem router does not find any WPS
devices, it will switch to standby mode.
6. To set up WPS using the Client’s PIN code, follow these steps:
a.Locate the WPS PIN code on your wireless device’s user
manual or on the device itself.
b.Key in the Client PIN code on the text box.
c.Click Start WPS to put your xDSL modem router into WPS
survey mode. The router’s LED indicators quickly flash three
times until the WPS setup is completed.
49
4.1.3Bridge
Bridge or WDS (Wireless Distribution System) allows your ASUS
Wireless xDSL Modem Router to connect to another wireless
access point exclusively, preventing other wireless devices or
stations to access your ASUS xDSL modem router. It can also be
considered as a wireless repeater where your ASUS Wireless xDSL
Modem Router communicates with another access point and
other wireless devices.
To set up the wireless bridge:
1. From the navigation panel, go to Advanced Settings >
Wireless > Bridge tab.
3. In the AP Mode field, select any of these options:
• AP Only: Disables the Wireless Bridge function.
• WDS Only: Enables the Wireless Bridge feature but prevents
other wireless devices/stations from connecting to the
router.
50
• Hybrid: Enables the Wireless Bridge feature and allows other
wireless devices/stations to connect to the router.
NOTE: In Hybrid mode, wireless devices connected to the ASUS Wireless
xDSL Modem Router will only receive half the connection speed of the
Access Point.
4. In the Connect to APs in list field, select Yes if you want to
connect to an Access Point listed in the Remote AP List.
5. On the Remote AP List, key in a MAC address and click the
Add button
to enter the MAC address of other available
Access Points.
NOTE: Any Access Point added to the list should be on the same Control
Channel as the ASUS xDSL modem router.
6.Click Apply.
51
4.1.4Wireless MAC Filter
Wireless MAC filter provides control over packets transmitted to
a specified MAC (Media Access Control) address on your wireless
network.
To set up the Wireless MAC filter:
1. From the navigation panel, go to Advanced Settings >
Wireless > Wireless MAC Filter tab.
2. Enable the Mac Filter Mode, then in the MAC Filter Mode
dropdown list, select either Accept or Reject.
• Select Accept to allow devices in the MAC filter list to access
to the wireless network.
• Select Reject to prevent devices in the MAC filter list to
access to the wireless network.
3. On the MAC filter list, click the Add
button and key in the
MAC address of the wireless device.
4.Click Apply.
52
4.1.5RADIUS Setting
RADIUS (Remote Authentication Dial In User Service) Setting
provides an extra layer of security when you choose WPAEnterprise, WPA2-Enterprise, or Radius with 802.1x as your
Authentication Mode.
To set up wireless RADIUS settings:
1. Ensure that the xDSL modem router’s authentication mode is
set to WPA-Enterprise, WPA2-Enterprise, or Radius with 802.1x.
NOTE: Please refer to section 4.1.1 General for configuring your xDSL
modem router’s Authentication Mode.
2. From the navigation panel, go to Advanced Settings >
Wireless > RADIUS Setting.
3. Select the frequency band.
4. In the Server IP Address field, key in your RADIUS server’s IP
Address.
5. In the Connection Secret field, assign the password to access
your RADIUS server.
6.Click Apply.
53
4.1.6Professional
The Professional screen provides advanced configuration options.
NOTE: We recommend that you use the default values on this page.
In the Professional Settings screen, you can configure the
following:
• Band: Select the frequency band that the professional
settings will be applied to.
• Enable Radio: Select Yes to enable wireless networking.
Select No to disable wireless networking.
• Enable Wireless Scheduler: You can set the time range
when wireless networking is enabled during the week.
• Date to Enable Radio: You can specify which days of the
week wireless networking is enabled.
• Time of Day to Enable Radio: You can specify a time range
when wireless networking is enabled during the week.
54
• Set AP isolated: The Set AP isolated item prevents wireless
devices on your network from communicating with each
other. This feature is useful if many guests frequently join or
leave your network. Select Yes to enable this feature or select
No to disable.
• Roaming Assistant: In network configurations that involve
multiple Access, Points or wireless repeater, wireless clients
sometimes cannot connect automatically to thefts available
AP because they are still connected to the main wireless
router. Enable this setting so that the client will disconnect
from the main wireless router if the signal strength is under a
specific threshold and connect to a stronger signal.
• Enable IGMP Snooping: Select Enable as the default value
to help improve the speed of transmission.
• Multicast rate (Mbps): Select the multicast transmission
rate or click Disable to switch off simultaneous single
transmission.
• RTS Threshold: Select a lower value for RTS (Request to
Send) Threshold to improve wireless communication in a
busy or noisy wireless network with high network traffic and
numerous wireless devices.
• DTIM Interval: DTIM (Delivery Traffic Indication Message)
Interval or Data Beacon Rate is the time interval before a
signal is sent to a wireless device in sleep mode indicating
that a data packet is awaiting delivery. The default value is
three milliseconds.
• Beacon Interval: Beacon Interval is the time between one
DTIM and the next. The default value is 100 milliseconds.
Lower the Beacon Interval value for an unstable wireless
connection or for roaming devices.
• Enable TX Bursting: Enable TX Bursting improves
transmission speed between the xDSL modem router and
802.11g devices.
• Enable Packet Aggregation: The default value is enabling
the process of joining multiple packets together into a single
transmission unit.
55
• Enable WMM APSD: Enable WMM APSD (Wi-Fi Multimedia
Automatic Power Save Delivery) to improve power
management between wireless devices. Select Disable to
switch off WMM APSD.
• Enable WMM DLS: Select Enable to set WMM Direct Link
Setup.
• TX Power adjustment: TX Power adjustment refers to the
milliWatts (mW) needed to power the radio signal output of
the xDSL modem router. Enter a value between 0 to 100.
NOTE: Increasing the TX Power adjustment values may affect the
stability of the wireless network.
4.2LAN
4.2.1LAN IP
The LAN IP screen allows you to modify the LAN IP settings of your
xDSL modem router.
NOTE: Any changes to the LAN IP address will be reflected on your
DHCP settings.
To modify the LAN IP settings:
1. From the navigation panel, go to Advanced Settings > LAN
> LAN IP tab.
2. Modify the IP address and Subnet Mask.
3. When done, click Apply.
56
4.2.2DHCP Server
Your xDSL modem router uses DHCP to assign IP addresses
automatically on your network. You can specify the IP address
range and lease time for the clients on your network.
To configure the DHCP server:
1. From the navigation panel, go to Advanced Settings > LAN
> DHCP Server tab.
2. In the Enable the DHCP Server field, tick Yes.
3. In the IP Pool Starting Address field, key in the starting IP
address.
4. In the IP Pool Ending Address field, key in the ending IP
address.
5. In the Lease Time field, specify in seconds when an assigned
IP address will expire. Once it reaches this time limit, the DHCP
server will then assign a new IP address.
57
NOTES:
• We recommend that you use an IP address format of 192.168.1.xxx
(where xxx can be any number between 2 and 254) when specifying
an IP address range.
• An IP Pool Starting Address should not be greater than the IP Pool
Ending Address.
6. In the DNS and WINS Server Settings section, key in your
DNS Server and WINS Server IP address if needed.
7. Your xDSL modem router can also manually assign IP
addresses to devices on the network. Up to 32 MAC Addresses
can be added to the DHCP list for manual assignment.
58
4.2.3Route
If your network makes use of more than one xDSL modem router,
you can configure a routing table to share the same Internet
service.
NOTE: We recommend that you do not change the default route
settings unless you have advanced knowledge of routing tables.
To configure the LAN Routing table:
1. From the navigation panel, go to Advanced Settings > LAN
> Route tab.
2. On the Enable static routes field, choose Yes.
3. On the Static Route List, enter the network information of
other access points or nodes. Click the Add
or Delete
button to add or remove a device on the list.
4.Click Apply.
59
4.2.4IPTV
The xDSL modem router supports connection to IPTV services
through an ISP or a LAN. The IPTV tab provides the configuration
settings needed to set up IPTV, VoIP, multicasting, and UDP for
your service. Contact your ISP for specific information regarding
your service.
60
4.3WAN
4.3.1Internet Connection
The Internet Connection screen allows you to configure the
settings of various WAN connection types.
To configure the WAN connection settings:
1. From the navigation panel, go to Advanced Settings > WAN
> Internet Connection tab.
2. Configure the following settings below. When done, click
Save.
• WAN Transfer Mode
• Choose your Internet Service Provider type. The choices
are VDSL WAN (PTM), ADSL WAN (ATM), Ethernet WAN.
Consult your ISP if the router is unable to obtain a valid IP
address or if you are unsure the WAN connection type.
• Service Unit: To set the value of transmission via Internet or
bridge.
61
• Enable: Select Yes to enable the Internet access. Select No
to disable the Internet access.
• Basic Config
• IP version: Select your IP version type. The choices are IPv4,
IPv4/IPv6, and IPv6.
• WAN Connection Type: Select the correct connection type
based on your ISP service type. The choices are Automatic
IP, Static IP, and PPPoE.
• Enable UPnP: UPnP (Universal Plug and Play) allows several
devices (such as routers, televisions, stereo systems, game
consoles, and cellular phone) to be controlled via an IP-based
network with or without a central control through a gateway.
UPnP connects PCs of all form factors, providing a seamless
network for remote configuration and data transfer. Using
UPnP, a new network device is discovered automatically.
Once connected to the network, devices can be remotely
configured to support P2P applications, interactive gaming,
video conferencing, and web or proxy servers. Unlike Port
forwarding, which involves manually configuring port
settings, UPnP automatically configures the router to accept
incoming connections and direct requests to a specific PC on
the local network.
• IPv4 Setting
• Connect to DNS Server automatically: Allows this router
to get the DNS IP address from the ISP automatically. A DNS
is a host on the Internet that translates Internet names to
numeric IP addresses.
• Enable NAT: NAT (Network Address Translation) is a system
where one public IP (WAN IP) is used to provide Internet
access to network clients with a private IP address in a LAN.
The private IP address of each network client is saved in a
NAT table and is used to route incoming data packets.
62
• Special Requirement from ISP
• Host Name: This field allows you to provide a host name for
your router. It is usually a special requirement from your ISP.
If your ISP assigned a host name to your computer, enter the
host name here.
• MAC Address: MAC (Media Access Control) address is a
unique identifier for your networking device. Some ISPs
monitor the MAC address of networking devices that
connect to their service and reject any unrecognized device
that attempt to connect. To avoid connection issues due to
an unregistered MAC address, you can:
• Contact your ISP and update the MAC address associated
with your ISP service.
• Clone or change the MAC address of the ASUS wireless
router to match the MAC address of the previous
networking device recognized by the ISP.
4.3.2 Dual WAN
DSL-AC55U provides Dual WAN support. Select Failover mode to
use a secondary WAN for backup network access.
63
4.3.3 Port Trigger
Port range triggering opens a predetermined incoming port for a
limited period of time whenever a client on the local area network
makes an outgoing connection to a specified port. Port triggering
is used in the following scenarios:
• More than one local client needs port forwarding for the
same application at a different time.
• An application requires specific incoming ports that are
different from the outgoing ports.
To set up Port Trigger:
1. From the navigation panel, go to Advanced Settings > WAN
> Port Trigger tab.
2. Configure the following settings below. When done, click
Apply.
• Enable Port Trigger: Choose Yes to enable Port Trigger.
• Well-Known Applications: Select popular games and web
services to add to the Port Trigger List.
• Description: Enter a short name or description for the service.
64
• Trigger Port: Specify a trigger port to open the incoming port.
• Protocol: Select the protocol, TCP, or UDP.
• Incoming Port: Specify an incoming port to receive inbound
data from the Internet.
• Protocol: Select the protocol, TCP, or UDP.
NOTES:
• When connecting to an IRC server, a client PC makes an outgoing
connection using the trigger port range 66660-7000. The IRC server
responds by verifying the username and creating a new connection
to the client PC using an incoming port.
• If Port Trigger is disabled, the router drops the connection because
it is unable to determine which PC is requesting for IRC access.
When Port Trigger is enabled, the router assigns an incoming port to
receive the inbound data. This incoming port closes once a specific
time period has elapsed because the router is unsure when the
application has been terminated.
• Port triggering only allows one client in the network to use a
particular service and a specific incoming port at the same time.
• You cannot use the same application to trigger a port in more than
one PC at the same time. The router will only forward the port back
to the last computer to send the router a request/trigger.
65
4.3.4Virtual Server/Port Forwarding
Port forwarding is a method to direct network traffic from the
Internet to a specific port or a specific range of ports to a device
or number of devices on your local network. Setting up Port
Forwarding on your router allows PCs outside the network to
access specific services provided by a PC in your network.
NOTE: When port forwarding is enabled, the ASUS router blocks
unsolicited inbound traffic from the Internet and only allows replies
from outbound requests from the LAN. The network client does not
have access to the Internet directly, and vice versa.
To set up Port Forwarding:
1. From the navigation panel, go to Advanced Settings > WAN
> Virtual Server / Port Forwarding tab.
66
2. Configure the following settings below. When done, click
Apply.
• Enable Port Forwarding: Choose Yes to enable Port
Forwarding.
• Famous Server List: Determine which type of service you
want to access.
• Famous Game List: This item lists ports required for popular
online games to work correctly.
• FTP Server Port: Avoid assigning the port range 20:21 for
your FTP server as this would conflict with the router’s native
FTP server assignment.
• Service Name: Enter a service name.
• Port Range: If you want to specify a Port Range for clients
on the same network, enter the Service Name, the Port
Range (e.g. 10200:10300), the LAN IP address, and leave the
Local Port empty. Port range accepts various formats such
as Port Range (300:350), individual ports (566,789) or Mix
(1015:1024,3021).
NOTES:
• When your network’s firewall is disabled and you set 80 as the HTTP
server’s port range for your WAN setup, then your http server/web
server would be in conflict with the router’s web user interface.
• A network makes use of ports in order to exchange data, with each
port assigned a port number and a specific task. For example, port 80
is used for HTTP. A specific port can only be used by one application
or service at a time. Hence, two PCs attempting to access data
through the same port at the same time would fail. For example, you
cannot set up Port Forwarding for port 100 for two PCs at the same
time.
67
• Local IP: Key in the client’s LAN IP address.
NOTE: Use a static IP address for the local client to make port forwarding
work properly. Refer to section 4.2 LAN for information.
• Local Port: Enter a specific port to receive forwarded packets.
Leave this field blank if you want the incoming packets to be
redirected to the specified port range.
• Protocol: Select the protocol. If you are unsure, select BOTH.
To check if Port Forwarding has been configured successfully:
• Ensure that your server or application is set up and running.
• You will need a client outside your LAN but has Internet
access (referred to as “Internet client”). This client should not
be connected to the ASUS router.
• On the Internet client, use the router’s WAN IP to access the
server. If port forwarding has been successful, you should be
able to access the files or applications.
Differences between port trigger and port forwarding:
• Port triggering will work even without setting up a specific
LAN IP address. Unlike port forwarding, which requires a
static LAN IP address, port triggering allows dynamic port
forwarding using the router. Predetermined port ranges are
configured to accept incoming connections for a limited
period of time. Port triggering allows multiple computers
to run applications that would normally require manually
forwarding the same ports to each PC on the network.
• Port triggering is more secure than port forwarding since the
incoming ports are not open all the time. They are opened
only when an application is making an outgoing connection
through the trigger port.
68
4.3.5DMZ
Virtual DMZ exposes one client to the Internet, allowing this
client to receive all inbound packets directed to your Local Area
Network.
Inbound traffic from the Internet is usually discarded and routed
to a specific client only if port forwarding or a port trigger has
been configured on the network. In a DMZ configuration, one
network client receives all inbound packets.
Setting up DMZ on a network is useful when you need incoming
ports open or you want to host a domain, web, or e-mail server.
Caution: Opening all the ports on a client to the Internet makes the
network vulnerable to outside attacks. Please be aware of the security
risks involved in using DMZ.
To set up DMZ:
1. From the navigation panel, go to Advanced Settings > WAN
> DMZ tab.
2. Configure the setting below. When done, click Apply.
• IP address of Exposed Station: Key in the client’s LAN IP
address that will provide the DMZ service and be exposed
on the Internet. Ensure that the server client has a static IP
address.
69
To remove DMZ:
1. Delete the client’s LAN IP address from the IP Address of
Exposed Station text box.
2. When done, click Apply.
4.3.6DDNS
Setting up DDNS (Dynamic DNS) allows you to access the router
from outside your network through the provided ASUS DDNS
Service or another DDNS service.
To set up DDNS:
1. From the navigation panel, go to Advanced Settings > WAN
> DDNS tab.
2. Configure the following settings below. When done, click
Apply.
• Enable the DDNS Client: Enable DDNS to access the ASUS
router via the DNS name rather than WAN IP address.
• Server and Host Name: Choose ASUS DDNS or other DDNS.
If you want to use ASUS DDNS, fill in the Host Name in the
format of xxx.asuscomm.com (xxx is your host name).
• If you want to use a different DDNS service, click FREE TRIAL
and register online first. Fill in the User Name or E-mail
Address and Password or DDNS Key fields.
70
NOTES:
DDNS service will not work under these conditions:
• When the xDSL modem router is using a private WAN IP address
(192.168.x.x, 10.x.x.x, or 172.16.x.x), as indicated by a yellow text.
• The router may be on a network that uses multiple NAT tables.
4.3.7NAT Passthrough
NAT Passthrough allows a Virtual Private Network (VPN)
connection to pass through the router to the network clients.
PPTP Passthrough, L2TP Passthrough, IPsec Passthrough,
RTSP Passthrough, H.323 Passthrough, and SIP Passthrough
are enabled by default.
To enable / disable the NAT Passthrough settings, go to the
Advanced Settings > WAN > NAT Passthrough tab. When done,
click Apply.
71
4.4IPv6
This xDSL modem router supports IPv6 addressing, a system
that supports more IP addresses. This standard is not yet widely
available. Contact your ISP if your Internet service supports IPv6.
To set up IPv6:
1. From the navigation panel, go to Advanced Settings > IPv6.
2. Select your Connection Type. The configuration options vary
depending on your selected connection type.
3. Enter your IPv6 LAN and DNS settings.
4.Click Apply.
NOTE: Please refer to your ISP regarding specific IPv6 information for
your Internet service.
72
4.5 VPN Server
VPN (Virtual Private Network) provides a secure communication
to a remote computer or remote network using a public network
such as the Internet.
NOTE: Before setting up a VPN connection, you would need the IP
address or domain name of the VPN server you are trying to access.
To set up access to a VPN server:
1. From the navigation panel, go to Advanced Settings > VPN
Server.
2. On the Enable VPN Server field, select Yes.
3. On the Network Place (Samba) Support field, select Yes.
4. Enter the user name and password for accessing the VPN
server. Click the
button.
5.Click Apply.
NOTE: For advanced VPN server settings, click the VPN Server tab to
configure broadcast support, authentication, MPPE Encryption, and
Client IP address range.
73
4.6Firewall
The xDSL modem router can serve as a hardware firewall for your
network.
NOTE: The Firewall feature is enabled by default.
4.6.1General
To set up basic Firewall settings:
1. From the navigation panel, go to Advanced Settings >
Firewall > General tab.
2. On the Enable Firewall field, select Yes.
3. On the Enable DoS protection, select Yes to protect your
network from DoS (Denial of Service) attacks though this may
affect your router’s performance.
4. You can also monitor packets exchanged between the LAN
and WAN connection. On the Logged packets type, select
Dropped, Accepted, or Both.
5.Click Apply.
74
4.6.2URL Filter
You can specify keywords or web addresses to prevent access to
specific URLs.
NOTE: The URL Filter is based on a DNS query. If a network client has
already accessed a website such as http://www.abcxxx.com, then the
website will not be blocked (a DNS cache in the system stores previously
visited websites). To resolve this issue, clear the DNS cache before
setting up the URL Filter.
To set up a URL filter:
1. From the navigation panel, go to Advanced Settings >
Firewall > URL Filter tab.
2. On the Enable URL Filter field, select Enabled.
3. Enter a URL and click the
button.
4.Click Apply.
75
4.6.3Keyword Filter
Keyword filter blocks access to webpages containing specified
keywords.
To set up a keyword filter:
1. From the navigation panel, go to Advanced Settings >
Firewall > Keyword Filter tab.
2. On the Enable Keyword Filter field, select Enabled.
3. Enter a word or phrase and click the
button.
4.Click Apply.
NOTES:
• The Keyword Filter is based on a DNS query. If a network client has
already accessed a website such as http://www.abcxxx.com, then
the website will not be blocked (a DNS cache in the system stores
previously visited websites). To resolve this issue, clear the DNS cache
before setting up the Keyword Filter.
• Web pages compressed using HTTP compression cannot be filtered.
HTTPS pages also cannot be blocked using a keyword filter.
76
4.6.4Network Services Filter
The Network Services Filter blocks LAN to WAN packet exchanges
and restricts network clients from accessing specific web services
such as Telnet or FTP.
To set up a Network Service filter:
1. From the navigation panel, go to Advanced Settings >
Firewall > Network Service Filter tab.
2. On the Enable Network Services Filter field, select Yes.
3. Select the Filter table type. Black List blocks the specified
network services. White List limits access to only the specified
network services.
4. Specify the day and time when the filters will be active.
5. To specify a Network Service to filter, enter the Source IP,
Destination IP, Port Range, and Protocol. Click the
button.
6.Click Apply.
77
4.7Administration
4.7.1System
The System page allows you to configure your xDSL modem
router settings.
To set up the System settings:
1. From the navigation panel, go to Advanced Settings >
Administration > System tab.
2. You can configure the following settings:
• Change router login password: You can change the
password and login name for the xDSL modem router by
entering a new name and password.
• WPS button behavior: The physical WPS button on the
xDSL modem router can be used to activate WPS.
• Time Zone: Select the time zone for your network.
• NTP Server: The xDSL modem router can access a NTP
(Network time Protocol) server in order to synchronize the
time.
78
• Enable Telnet: Click Yes to enable Telnet services on the
network. Click No to disable Telnet.
• Authentication Method: You can select HTTP, HTTPS, or
both protocols to secure router access.
• Enable Web Access from WAN: Select Yes to allow devices
outside the network to access the xDSL modem router GUI
settings. Select No to to prevent access.
3.Click Apply.
4.7.2Firmware Upgrade
NOTE: Download the latest firmware from the ASUS website at
http://www.asus.com
To upgrade the firmware:
1. From the navigation panel, go to Advanced Settings >
Administration > Firmware Upgrade tab.
2. In the New Firmware File field, click Browse to locate the
downloaded file.
3.Click Upload.
79
NOTES:
• When the upgrade process is complete, wait for some time for the
system to reboot.
• If the upgrade process fails, the xDSL modem router automatically
enters rescue mode and the power LED indicator on the front panel
starts flashing slowly. To recover or restore the system, refer to
section 5.2 Firmware Restoration.
4.7.3Restore/Save/Upload Setting
To restore/save/upload xDSL modem router settings:
1. From the navigation panel, go to Advanced Settings >
Administration > Restore/Save/Upload Setting tab.
2. Select the tasks that you want to do:
• To restore to the default factory settings, click Restore, and
click OK in the confirmation message.
• To save the current system settings, click Save, navigate to
the folder where you intend to save the file and click Save.
80
• To restore from a saved system settings file, click Browse to
locate your file, then click Upload.
NOTE:If issues occur, upload the latest firmware version and configure
new settings. Do not restore the router to its default settings.
4.7.4DSL Setting
This page allows you to configure your DSL settings.
IMPORTANT! Please contact your ISP to obtain your DSL settings
before doing any changes.
You can configure the following settings:
• DSL Modulation: This device supports VDSL2, ADSL2+,
ADSL2, G.DMT, T1.413 and G.lite. The system Auto Sync-Up by
default.
81
• Annex Mode: This device supports different DSL Variant
(Annex) – Annex A, Annex I, Annex A/L, Annex M, A/J/J/L/M
(multiple-mode), Annex B, Annex B/J (multiple-mode).
Contact your ISP to find out the DSL variant (annex) that is
used on your DSL line.
• Dynamic Line Adjustment (ADSL): This function allows
the system to monitor and maintain the stability of the
ADSL line. This function is enabled by default, and the
system adopts corresponding changes based on the
current ADSL line condition.
• Stability Adjustement (ADSL): It allows you to configure
the Signal-to-Noise Ratio Offset. Set the value for this item
based on the following conditions:
• Normal DSL connection: Set the value from 1 dB ~ 10dB for
maximum performance.
• Unstable or no ADSL connection: Set the value to a
negative dB such as -1 dB.
• Persistent issue with unstable or no ADSL connection: Set
the value from -2dB ~ -10 dB for maximum stability.
• Rx AGC GAIN Adjustment (ADSL): Allows you to configure
Rx AGC GAIN (Auto Gain Control) for your ADSL line. You
can set this item to any of these modes:
• Stable: Select this mode to get a stable ADSL connection.
• High Performance: Select this mode to improve the current
downstream speed.
• Default: Select this mode for your xDSL modem router to
automatically assign the suitable mode for your ADSL line.
• Stability Adjustment (VDSL): It allows you to configure
the target SNRM (Signal-to-Noise Ratio Margin) for your
VDSL connection. When configuring this item, you may
consider the following scenarios:
• For maximum downstream performance, set this item to a
value lower than the original (such as from 8dB to 7dB or
lower).
IMPORTANT! Setting a low value may weaken your xDSL modem router
defense against line noise, and may result to VDSL sync loss or failure.
• For a more stable VDSL connection, set this item to a higher
value such as 9dB ~ 30dB.
82
• Tx Power Control (VDSL): It allows you to configure the Tx
Power for VDSL to improve the downstream speed. A low
Tx Power value increases the downstream speed but affects
the upstream speed, and vice versa.
• Rx AGC GAIN Adjustment (VDSL): Allows you to configure
Rx AGC GAIN (Auto Gain Control) for your VDSL line. You can
set this item to any of these modes:
• Stable: Select this mode to get a stable VDSL connection.
• High Performance: Select this mode to improve the current
downstream speed.
• Default: Select this mode for your xDSL modem router to
automatically assign the suitable mode for your VDSL line.
• UPBO/Upstream Power Back Off (VDSL): This item
allows you to enable or disable UPBO (Upstream Power
Back Off) for VDSL. DSLAM (Digital Subscriber Line Access
Multiplexer) uses UPBO to reduce the Tx Power of your xDSL
modem router. In some cases, UPBO control from DSLAM
may lead to sync issue, such as Tx Power is too low to sync
at minimum rate. Disable this item to prevent any DSLAMrelated sync issues.
• Seamless Rate Adaptation: This item allows you to enable
SRA (Seamless Rate Adaptation) for consistent data transfer
rates and preventing dropped connections. You may
disable this item when your connection is very stable and
there is a decrease in download or upload speed.
• Bitswap: This item allows you to enable Bitswap, which
adjusts bits allocated for bins/channels. Busy or congested
bins/channels are assigned fewer bits while available
channels are allocated more bits to handle.
• VDSL Profile: This item allows you to configure the VDSL
Profile. The default value is 30a multi mode.
NOTE:For some ISPs with non-standard 30a multi mode VDSL DSLAM
sync setting, such as for ISP services in Germany, set the VDSL Profile to
17a multi mode to sync up the VDSL line.
83
4.7.5Feedback
DSL feedback is used to diagnose problems and help to improve
the user experience of ASUS xDSL modem router. Complete the
form, and it will be send to ASUS Support Team.
84
4.8 System Log
System Log contains your recorded network activities.
NOTE: System log resets when the router is rebooted or powered off.
To view your system log:
1. From the navigation panel, go to Advanced Settings >
System Log.
2. You can view your network activities in any of these tabs:
• General Log
• DHCP Leases
• Wireless Log
• Port Forwarding
• DSL Log
85
5Utilities
NOTES:
• Install the xDSL modem router's utilities from the bundled support
CD.
• If Autorun is disabled, run setup.exe from the root directory of the
support CD.
• The utilities are not supported on MAC OS.
5.1 Device Discovery
Device Discovery is an ASUS WLAN utility that detects an ASUS
Wireless xDSL Modem Router device, and allows you to configure
the wireless networking settings.
To launch the Device Discovery utility:
• From your computer’s desktop, click
Start > All Programs > ASUS Utility > Device Discovery.
NOTE: When you set the router to Access Point mode, you need to use
Device Discovery to get the router’s IP address.
86
5.2 Firmware Restoration
Firmware Restoration is used on an ASUS Wireless xDSL Modem
Router that failed during its firmware upgrading process. It
uploads the firmware that you specify. The process takes about
three to four minutes.
IMPORTANT: Launch the rescue mode on the router before using the
Firmware Restoration utility.
NOTE: This feature is not supported on MAC OS.
To launch the rescue mode and use the Firmware Restoration
utility:
1. Unplug the xDSL modem router from the power source.
2. Hold the Reset button at the rear panel and simultaneously
replug the xDSL modem router into the power source. Release
the Reset button when the Power LED at the front panel
flashes slowly, which indicates that the xDSL modem router is
in the rescue mode.
87
3. Set a static IP on your computer and use the following to set
up your TCP/IP settings:
IP address: 192.168.1.x
Subnet mask: 255.255.255.0
4. From your computer’s desktop, click
Start > All Programs > ASUS Utility DSL-AC55U xDSL
modem router > Firmware Restoration.
5. Specify a firmware file, then click Upload.
NOTE: This is not a firmware upgrade utility and cannot be used on a
working ASUS XDSL modem router. Normal firmware upgrades must be
done through the web interface. Refer to Chapter 4: Configuring the
Advanced Settings for more details.
5.3 Setting up your printer server
5.3.1ASUS EZ Printer Sharing
ASUS EZ Printing Sharing utility allows you to connect a USB
printer to your xDSL modem router’s USB port and set up the
print server. This allows your network clients to print and scan files
wirelessly.
88
NOTE: The print server function is supported on Windows® XP,
Windows® Vista, and Windows® 7.
To set up the EZ Printer sharing mode:
1. From the navigation panel, go to General > USB Application
> Network Printer Server.
2.Click Download Now! to download the network printer
utility.
NOTE:Network printer utility is supported on Windows® XP, Windows®
Vista, and Windows® 7 only. To install the utility on Mac OS, select Use
LPR protocol for sharing printer.
3. Unzip the downloaded file and click the Printer icon to run the
network printer setup program.
89
4. Follow the onscreen instructions to set up your hardware,
then click Next.
5. Wait a few minutes for the initial setup to finish. Click Next.
6.Click Finish to complete the installation.
DSL-AC55U
90
7. Follow the Windows® OS instructions to install the printer
driver.
8. After the printer’s driver installation is complete, network
clients can now use the printer.
91
5.3.2Using LPR to Share Printer
You can share your printer with computers running on Windows®
and MAC operating system using LPR/LPD (Line Printer Remote/
Line Printer Daemon).
Sharing your LPR printer
To share your LPR printer:
1. From the Windows® desktop, click Start > Devices and
Printers > Add a printer to run the Add Printer Wizard.
2.Select Add a local printer and then click Next.
92
3.Select Create a new port then set Type of Port to Standard
TCP/IP Port. Click New Port.
4. In the Hostname or IP address field, key in the IP address of
the xDSL modem router then click Next.
93
5.Select Custom then click Settings.
6.Set Protocol to LPR. In the Queue Name field, key in
LPRServer then click OK to continue.
94
7.Click Next to finish setting up the standard TCP/IP port.
8. Install the printer driver from the vendor-model list. If your
printer is not in the list, click Have Disk to manually install the
printer drivers from a CD-ROM or file.
95
9.Click Next to accept the default name for the printer.
10.Click Finish to complete the installation.
96
5.4 Download Master
Download Master is a utility that helps you download files even
while your laptops or other devices are switched off.
NOTE:You need a USB device connected to the xDSL modem router to
use Download Master.
To use Download Master:
1.Click General > USB application > Download Master to
download and install the utility automatically.
NOTE: If you have more than one USB drive, select the USB device you
want to download the files to.
2. After the download process is finished, click the Download
Master icon to start using the utility.
3.Click Add to add a download task.
4. Select a download type such as BitTorrent, HTTP, or FTP.
Provide a torrent file or a URL to begin downloading.
NOTE: For details on Bit Torrent, refer to section 5.4.1 Configuring the
Bit Torrent download settings.
97
5. Use the navigation panel to configure the advanced settings.
5.4.1Configuring Bit Torrent download settings
To configure BitTorrent download settings:
1. From Download Master’s navigation panel, click Bit Torrent to
launch the Bit Torrent Setting page.
2. Select a specific port for your download task.
3. To prevent network congestion, you can limit the maximum
upload and download speeds under Speed Limits.
4. You can limit the maximum number of allowed peers and
enable or disable file encryption during downloads.
98
5.4.2NZB settings
You can set up a USENET server to download NZB files. After
entering USENET settings, Apply.
99
6Troubleshooting
This chapter provides solutions for issues you may encounter with
your router. If you encounter problems that are not mentioned in
this chapter, visit the ASUS support site at:
http://support.asus.com/ for more product information and
contact details of ASUS Technical Support.
6.1 Basic Troubleshooting
If you are having problems with your router, try these basic steps
in this section before looking for further solutions.
Upgrade Firmware to the latest version.
1. Launch the Web GUI. Go to Advanced Settings >
Administration > Firmware Upgrade tab. Click Check to
verify if the latest firmware is available.
2. If the latest firmware is available, visit the ASUS global
website at http://www.asus.com/Networks/Wireless_Routers/
DSLAC55U/#download to download the latest firmware.
3. From the Firmware Upgrade page, click Browse to locate the
firmware file.
4.Click Upload to upgrade the firmware.
100
Restart your network in the following sequence:
1. Turn off the modem.
2. Unplug the modem.
3. Turn off the router and computers.
4. Plug in the modem.
5. Turn on the modem and then wait for 2 minutes.
6. Turn on the router and then wait for 2 minutes.
7. Turn on computers.
Check if your Ethernet cables are plugged properly.
• When the Ethernet cable connecting the router with the
modem is plugged in properly, the WAN LED will be on.
• When the Ethernet cable connecting your powered-on
computer with the router is plugged in properly, the
corresponding LAN LED will be on.
Check if the wireless setting on your computer matches that
of your computer.
• When you connect your computer to the router wirelessly,
ensure that the SSID (wireless network name), encryption
mehtod, and password are correct.
Check if your network settings are correct.
• Each client on the network should have a valid IP address.
ASUS recommends that you use the xDSL modem router’s
DHCP server to assign IP addresses to computers on your
network.
101
•
102
Some cable modem service providers require you to use
the MAC address of the computer initially registered on
the account. You can view the MAC address in the web GUI,
Network Map > Clients page, and hover the mouse pointer
over your device in Client Status.
6.2 Frequently Asked Questions (FAQs)
I cannot access the router GUI using a web browser
•
•
•
If your computer is wired, check the Ethernet cable
connection and LED status as described in the previous
section.
Ensure that you are using the correct login information. The
default factory login name and password is “admin/admin”.
Ensure that the Caps Lock key is disabled when you enter the
login information.
Delete the cookies and files in
your web browser. For Internet
Explorer 8, follow these steps:
1.Launch Internet Explorer 8,
then click Tools > Internet
Options.
2.In the General tab,
under Browsing history,
click Delete…, select
Temporary Internet Files
and Cookies then click
Delete.
NOTES:
• The commands for deleting cookies and files vary with web
browsers.
•
Disable proxy server settings, cancel the dial-up connection,
and set the TCP/IP settings to obtain IP addresses
automatically. For more details, refer to Chapter 1 of this user
manual.
• Ensure that you use CAT5e or CAT6 ethernet cables.
103
The client cannot establish a wireless connection with the
router.
NOTE:If you are having issues connecting to 5GHz network, make
sure that your wireless device supports 5GHz or features dual band
capabilities.
•
•
104
Out of Range:
• Move the router closer to the wireless client.
• Try to adjust antennas of the router to the best direction
as described in section 1.4 Positioning your xDSL
modem router.
DHCP server has been disabled:
1.Launch the web GUI. Go to General > Network Map>
Clients and search for the device that you want to
connect to the router.
2.If you cannot find the device in the Network Map, go to
Advanced Settings > LAN > DHCP Server, Basic Config
list, select Yes on the Enable the DHCP Server.
•
SSID has been hidden. If your device can find SSIDs from other
routers but cannot find your router’s SSID, go to Advanced
Settings > Wireless > General, select No on Hide SSID, and
select Auto on Control Channel.
•
If you are using a wireless LAN adapter, check if the wireless
channel in use conforms to the channels available in your
country/area. If not, adjust the channel, channel bandwidth,
and wireless mode.
If you still cannot connect to the router wirelessly, you can
reset your router to factory default settings. In the router
GUI,click Administration > Restore/Save/Upload Setting
and click Restore.
•
105
Internet is not accessible.
•
•
106
Check if your router can connect to your ISP’s WAN IP address.
To do this, launch the web GUI and go to General> Network
Map, and check the Internet Status.
If your router cannot connect to your ISP’s WAN IP address,
try restarting your network as described in the section
Restart your network in following sequence under Basic
Troubleshooting.
•
The device has been blocked via the Parental Control
function. Go to General > Parental Control and see if the
device is in the list. If the device is listed under Client Name,
remove the device using the Delete button or adjust the Time
Management Settings.
•
If there is still no Internet access, try to reboot your computer
and verify the network’s IP address and gateway address.
•
Check the status indicators on the ADSL modem and the xDSL
modem router. If the WAN LED on the xDSL modem router is
not ON, check if all cables are plugged properly.
You forgot the SSID (network name) or network password
•
•
Setup a new SSID and encryption key via a wired connection
(Ethernet cable). Launch the web GUI, go to Network Map,
click the router icon, enter a new SSID and encryption key,
and then click Apply.
Reset your router to the default settings. Launch the web GUI,
go to Administration > Restore/Save/Upload Setting, and
click Restore. The default login account and password are
both “admin”.
How to restore the system to its default settings?
Go to Administration > Restore/Save/Upload Setting, and
click Restore.
The following are the factory default settings:
User Name: admin
Password: admin
Enable DHCP: Yes (if WAN cable is plugged in)
IP address: http://router.asus.com
Domain Name: (Blank)
Subnet Mask: 255.255.255.0
DNS Server 1: 192.168.1.1
DNS Server 2: (Blank)
SSID (2.4GHz): ASUS
SSID (5GHz): ASUS_5G
•
Firmware upgrade failed.
Launch the rescue mode and run the Firmware Restoration utility.
Refer to section 5.2 Firmware Restoration on how to use the
Firmware Restoration utility.
107
Cannot access Web GUI
Before configuring your xDSL modem router, do the steps
described in this section for your host computer and network
clients.
A. Disable the proxy server, if enabled.
Windows® 7
1.Click Start > Internet
Explorer to launch the
browser.
2.Click Tools > Internet options
> Connections tab > LAN
settings.
3.From the Local Area
Network (LAN) Settings
screen, untick Use a
proxy server for your
LAN.
4.Click OK when done.
108
MAC OS
1.From your Safari
browser, click Safari
> Preferences >
Advanced > Change
Settings...
2.From the Network
screen, deselect FTP
Proxy and Web Proxy
(HTTP).
3.Cllick Apply Now when
done.
NOTE:Refer to your browser's help feature for details on disabling the
proxy server.
B.Set the TCP/IP settings to automatically obtain an IP
address.
Windows® 7
1.Click Start > Control Panel
> Network and Internet
> Network and Sharing
Center > Manage network
connections.
2.Select Internet Protocol
Version 4 (TCP/IPv4) or
Internet Protocol Version
6 (TCP/IPv6), then click
Properties.
109
3. To obtain the IPv4 IP
settings automatically,
tick Obtain an IP address
automatically.
To obtain the IPv6 IP
settings automatically, tick
Obtain an IPv6 address
automatically.
4.Click OK when done.
MAC OS
1. Click the Apple icon
located on the top left
of your screen.
2.Click System
Preferences > Network
> Configure...
3. From the TCP/IP tab,
select Using DHCP in
the Configure IPv4
dropdown list.
4.Cllick Apply Now when
done.
NOTE:Refer to your operating system’s help and support feature for
details on configuring your computer’s TCP/IP settings.
110
C.
Disable the dial-up connection, if enabled.
Windows® 7
1.Click Start > Internet Explorer
to launch the browser.
2.Click Tools > Internet options
> Connections tab.
3.Tick Never dial a connection.
4.Click OK when done.
NOTE:Refer to your browser's help feature for details on disabling the
dial-up connection.
111
Appendices
Notices
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our
commitment to the highest standards for protecting our
environment. We believe in providing solutions for you to be able
to responsibly recycle our products, batteries, other components,
as well as the packaging materials. Please go to http://csr.asus.
com/english/Takeback.htm for the detailed recycling information
in different regions.
REACH
Complying with the REACH (Registration, Evaluation,
Authorisation, and Restriction of Chemicals) regulatory
framework, we published the chemical substances in our products
at ASUS REACH website at
http://csr.asus.com/english/index.aspx
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
112
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
IMPORTANT! This device within the 5.15 ~ 5.25 GHz is restricted to
indoor operations to reduce any potential for harmful interference to
co-channel MSS operations.
CAUTION: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating
in conjunction with any other antenna or transmitter.
113
Safety Information
To maintain compliance with FCC’s RF exposure guidelines, this
equipment should be installed and operated with minimum
distance 20cm between the radiator and your body. Use on the
supplied antenna.
Declaration of Conformity for R&TTE directive 1999/5/EC
Essential requirements – Article 3
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950-1 has been
conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility –
Article 3.1b
Testing for electromagnetic compatibility according to EN
301 489-1 and EN 301 489-17 has been conducted. These are
considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328 & EN 301
893 have been conducted. These are considered relevant and
sufficient.
Operate the device in 5150-5250 MHz frequency band for indoor
use only.
CE Mark Warning
This is a Class B product, in a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
This equipment may be operated in AT, BE, CY, CZ, DK, EE, FI, FR,
DE, GR, HU, IE, IT, LU, MT, NL, PL, PT, SK, SL, ES, SE, GB, IS, LI, NO, CH,
BG, RO, RT.
114
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003
and RSS-210.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the ASUS Wireless Device is below
the Industry Canada (IC) radio frequency exposure limits. The
ASUS Wireless Device should be used in such a manner such
that the potential for human contact during normal operation is
minimized.
This device has been evaluated for and shown compliant with
the IC Specific Absorption Rate (“SAR”) limits when installed in
specific host products operated in portable exposure conditions
(antennas are less than 20 centimeters of a person’s body).
This device has been certified for use in Canada. Status of the
listing in the Industry Canada’s REL (Radio Equipment List) can be
found at the following web address: http://www.ic.gc.ca/app/sitt/
reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be
found at the following web: http://www.ic.gc.ca/eic/site/smt-gst.
nsf/eng/sf08792.html
Canada, avis d’Industry Canada (IC)
Cet appareil numérique de classe B est conforme aux normes
115
canadiennes ICES-003 et RSS-210.
Son fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne doit pas causer d’interférence et (2) cet appareil
doit accepter toute interférence, notamment les interférences qui
peuvent a ecter son fonctionnement.
NCC 警語
經型式認證合格之低功率射頻電機,非經許可,公司、商號或
使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通
信;經發現有干擾現象時,應立即停用,並改善至無干擾時方
得繼續使用。前項合法通信,指依電信法規定作業之無線電通
信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電
波輻射性電機設備之干擾。
GNU General Public License
Licensing information
This product includes copyrighted third-party software licensed
under the terms of the GNU General Public License. Please see The
GNU General Public License for the exact terms and conditions of
this license. All future firmware updates will also be accompanied
with their respective source code. Please visit our web site for
updated information. Note that we do not offer direct support for
the distribution.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.
116
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share
and change free software--to make sure the software is free for all
its users. This General Public License applies to most of the Free
Software Foundation’s software and to any other program whose
authors commit to using it. (Some other Free Software Foundation
software is covered by the GNU Library General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code or
can get it if you want it, that you can change the software or use
pieces of it in new free programs; and that you know you can do
these things.
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the
rights. These restrictions translate to certain responsibilities for
you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get
the source code. And you must show them these terms so they
know their rights.
117
We protect your rights with two steps: (1) copyright the software,
and (2) offer you this license which gives you legal permission to
copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make
certain that everyone understands that there is no warranty for
this free software. If the software is modified by someone else and
passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will
not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making
the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone’s free use or not
licensed at all.
The precise terms and conditions for copying, distribution and
modification follow.
Terms & conditions for copying, distribution, & modification
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying it may
be distributed under the terms of this General Public License.
The “Program”, below, refers to any such program or work, and
a “work based on the Program” means either the Program or
any derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or
with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the
term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification
are not covered by this License; they are outside its scope. The
118
act of running the Program is not restricted, and the output
from the Program is covered only if its contents constitute
a work based on the Program (independent of having been
made by running the Program). Whether that is true depends
on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s
source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy
an appropriate copyright notice and disclaimer of warranty;
keep intact all the notices that refer to this License and to the
absence of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any
portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the
terms of Section 1 above, provided that you also meet all of
these conditions:
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the date of any
change.
b) You must cause any work that you distribute or publish,
that in whole or in part contains or is derived from the
Program or any part thereof, to be licensed as a whole at no
charge to all third parties under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started
running for such interactive use in the most ordinary way, to
print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users may
redistribute
119
the program under these conditions, and telling the user
how to view a copy of this License. (Exception: if the Program
itself is interactive but does not normally print such an
announcement, your work based on the Program is not
required to print an announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and
separate works in themselves, then this License, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections
as part of a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution of
derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on
the Program with the Program (or with a work based on the
Program) on a volume of a storage or distribution medium
does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on
it, under Section 2) in object code or executable form under
the terms of Sections 1 and 2 above provided that you also do
one of the following:
a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily
used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than your
cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to
120
be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to
the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution and
only if you received the program in object code or executable
form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of
the work for making modifications to it. For an executable
work, complete source code means all the source code for all
modules it contains, plus any associated interface definition
files, plus the scripts used to control compilation and
installation of the executable. However, as a special exception,
the source code distributed need not include anything that
is normally distributed (in either source or binary form) with
the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that
component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same
place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with
the object code.
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this License. Any
attempt otherwise to copy, modify, sublicense or distribute
the Program is void, and will automatically terminate your
rights under this License. However, parties who have received
copies, or rights, from you under this License will not have
their licenses terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have
not signed it. However, nothing else grants you permission to
modify or distribute the Program or its derivative works. These
actions are prohibited by law if you do not accept this License.
121
Therefore, by modifying or distributing the Program (or any
work based on the Program), you indicate your acceptance
of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Program or works
based on it.
6. Each time you redistribute the Program (or any work based
on the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the
Program subject to these terms and conditions. You may not
impose any further restrictions on the recipients’ exercise
of the rights granted herein. You are not responsible for
enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the
conditions of this License. If you cannot distribute so as to
satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you
may not distribute the Program at all. For example, if a patent
license would not permit royalty-free redistribution of the
Program by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and
this License would be to refrain entirely from distribution of
the Program.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended to
apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose
of protecting the integrity of the free software distribution
system, which is implemented by public license practices.
Many people have made generous contributions to the wide
122
range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software
through any other system and a licensee cannot impose that
choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the
Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that
distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation
as if written in the body of this License.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time to
time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the
Program specifies a version number of this License which
applies to it and “any later version”, you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation.
If the Program does not specify a version number of this
License, you may choose any version ever published by the
Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to
the author to ask for permission.
123
For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing
and reuse of software generally.
NO WARRANTY
11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR
ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE
THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS
124
For Turkey only
Authorised distributors in Turkey:
BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.
Tel. No.:
+90 212 3311000
Address:
AYAZAGA MAH. KEMERBURGAZ CAD. NO.10
AYAZAGA/ISTANBUL
CIZGI Elektronik San. Tic. Ltd. Sti.
Tel. No.:
+90 212 3567070
Address:
CEMAL SURURI CD. HALIM MERIC IS MERKEZI
No: 15/C D:5-6 34394 MECIDIYEKOY/
ISTANBUL
KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC.
A.S.
Tel. No.:
+90 216 5288888
Address:
EMEK MAH.ORDU CAD. NO:18, SARIGAZi,
SANCAKTEPE ISTANBUL
AEEE Yönetmeliğine Uygundur.
125
ASUS Contact information
ASUSTeK COMPUTER INC. (Asia Pacific)
Address
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
Websitewww.asus.com.tw
Technical Support
Telephone+886228943447
Support Fax
+886228907698
Online support
support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Address
800 Corporate Way, Fremont, CA 94539, USA
Telephone+15107393777
Fax
+15106084555
Websiteusa.asus.com
Online support
support.asus.com
ASUS COMPUTER GmbH (Germany and Austria)
Address
Harkort Str. 21-23, D-40880 Ratingen, Germany
Support Fax
+49-2102-959931
Websiteasus.com/de
Online contact
eu-rma.asus.com/sales
Technical Support
Telephone (Component)+49-2102-5789555
Telephone Germany
(System/Notebook/Eee/LCD) +49-2102-5789557
Telephone Austria
(System/Notebook/Eee/LCD) +43-820-240513
Support Fax+49-2102-959911
Online supportsupport.asus.com
126
Networks Global Hotline Information
Region
Country
Service Hours
09:00-13:00 ;
14:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
Cyprus
800-92491
France
Hungary
0033-170949400
0049-1805010920
0049-1805010923
(component support)
0049-2102959911 ( Fax )
0036-15054561
Italy
199-400089
Greece
00800-44142044
Austria
Netherlands/
Luxembourg
Belgium
Norway
Sweden
Finland
Denmark
Poland
Spain
Portugal
Slovak Republic
Czech Republic
Switzerland-German
Switzerland-French
Switzerland-Italian
United Kingdom
Ireland
Russia and CIS
Ukraine
0043-820240513
09:00-17:30 Mon-Fri
09:00-13:00 ;
14:00-18:00 Mon-Fri
09:00-13:00 ;
14:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
0031-591570290
09:00-17:00 Mon-Fri
0032-78150231
0047-2316-2682
+46-858769407
00358-969379690
0045-38322943
0048-225718040
0034-902889688
00351-707500310
00421-232162621
00420-596766888
0041-848111010
0041-848111014
0041-848111012
+44-1442265548
0035-31890719918
008-800-100-ASUS
0038-0445457727
09:00-17:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
10:00-19:00 Mon-Fri
09:00-18:00 Mon-Fri
08:30-17:30 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
08:00-17:00 Mon-Fri
08:00-17:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
Germany
Europe
Hotline Number
09:00-18:00 Mon-Fri
10:00-17:00 Mon-Fri
127
Networks Global Hotline Information
Region
Country
Australia
New Zealand
Japan
Korea
Thailand
Asia-Pacific
Singapore
Malaysia
Philippine
India
India(WL/NW)
Indonesia
Americas
128
Hotline Numbers
1300-278788
0800-278788
0800-1232787
0081-570783886
( Non-Toll Free )
0082-215666868
0066-24011717
1800-8525201
0065-64157917
0065-67203835
( Repair Status Only )
0060-320535077
1800-18550163
1800-2090365
0062-2129495000
500128 (Local Only)
Vietnam
1900-555581
Hong Kong
USA
Canada
Mexico
00852-35824770
1-812-282-2787
001-8008367847
Service Hours
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-17:00 Sat-Sun
09:00-18:00 Mon-Fri
09:00-17:00 Sat-Sun
09:30-17:00 Mon-Fri
09:00-18:00 Mon-Fri
11:00-19:00 Mon-Fri
11:00-19:00 Mon-Fri
11:00-13:00 Sat
10:00-19:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Sat
09:00-21:00 Mon-Sun
09:30-17:00 Mon-Fri
9:30 – 12:00 Sat
08:00-12:00
13:30-17:30 Mon-Sat
10:00-19:00 Mon-Sat
8:30-12:00 EST Mon-Fri
9:00-18:00 EST Sat-Sun
08:00-20:00 CST Mon-Fri
08:00-15:00 CST Sat
Networks Global Hotline Information
Region
Middle
East +
Africa
Country
Egypt
Saudi Arabia
UAE
Turkey
South Africa
Israel
Romania
Bosnia
Herzegovina
Bulgaria
Balkan
Countries Croatia
Montenegro
Serbia
Slovenia
Estonia
Latvia
Baltic
Countries Lithuania-Kaunas
Lithuania-Vilnius
Hotline Numbers
800-2787349
800-1212787
00971-42958941
0090-2165243000
0861-278772
*6557/00972-39142800
*9770/00972-35598555
0040-213301786
Service Hours
09:00-18:00 Sun-Thu
09:00-18:00 Sat-Wed
09:00-18:00 Sun-Thu
09:00-18:00 Mon-Fri
08:00-17:00 Mon-Fri
08:00-17:00 Sun-Thu
08:30-17:30 Sun-Thu
09:00-18:30 Mon-Fri
00387-33773163
09:00-17:00 Mon-Fri
00359-70014411
00359-29889170
00385-16401111
00382-20608251
00381-112070677
00368-59045400
00368-59045401
00372-6671796
00371-67408838
00370-37329000
00370-522101160
09:30-18:30 Mon-Fri
09:30-18:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-17:00 Mon-Fri
08:00-16:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
NOTE:For more information, visit the ASUS support site at:
http://support.asus.com
Manufacturer:
Authorised
representative
in Europe:
ASUSTeK Computer Inc.
Tel:
+886-2-2894-3447
Address: 4F, No. 150, LI-TE RD., PEITOU,
TAIPEI 112, TAIWAN
ASUS Computer GmbH
Address: HARKORT STR. 21-23, 40880
RATINGEN, GERMANY
129
Download PDF
Similar pages