Tape Light Installation Instructions Tape Light Safety

Tape Light Installation Instructions
(Part #’s TPL1232-500, TPL1280-500, TPL12RD-500 or TPL12BL-500)
PARTS INCLUDED:
Tape Light (TPL12XX-LL)
TOOLS NEEDED (Customer Provided):
Clear Track – Optional
(STCHAN-TT/CLEAR)
Electric Drill w/ Phillips Bit
#4 Wood Screws
Tape Light Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS. READ CAREFULLY FOR YOUR PROTECTION AND SAVE ALL INSTRUCTIONS.
*Disconnect power before installing, adding or changing any component.
*To avoid a hazard to children, account for all parts and destroy all packing materials.
*Please note that the Tape light can only be used with 12V power. Anything that is higher voltage will run the risk of burning out the light.
*Do not install any luminaire assembly closer than 6" from any combustible material.
Tape Light Warranty Information
GENERAL PRODUCT LIMITED WARRANTY:
ITC warrants, to the original consumer, that the product will be free of defects in materials and/or workmanship for the period of time set forth herein. This warranty period will
begin from the later of the original date of purchase of the product or the date of sale of the recreational vehicle or boat in which the product is installed is first sold to the first
consumer provided that adequate documentation of said consumer sale date is provided to ITC. Adequacy of the authenticity of the consumer sale date will be determined
by ITC in it sole discretion. In the event the consumer sale date is not provided or not determined to be adequate by ITC, then the warranty period will begin on the original
date of purchase of the product from ITC. Except as set forth below, this general product limited warranty will extend for three years. All exterior faucets, exterior showers,
exterior plumbing products, rope lighting and clocks will have a one year warranty period. All assist handles will have a two year warranty period, provided that crazing caused
by chemical attack from a contaminant is not covered by any warranty. Products that are primarily comprised of 316 stainless steel will have a five year warranty period. Bulbs,
including halogen, incandescent, xenon, and light emitting diodes (LEDs) are excluded from the warranty.
MAXIMUM LIABILITY ITC's liability to repair or replace a damaged item shall be limited to the original purchaser of the item at the original invoice price of the damaged unit,
acceptable labor charges, acceptable freight charges, and dealer charge backs mandated by state law. ITC will not credit customers for excessive labor or freight charges or
unauthorized dealer or customer markup fees. Acceptable freight and labor charges are available from ITC upon request.
INSPECTION ITC reserves the right to review the damaged product and the site where the damage occurred. ITC may require the purchaser to ship the item to ITC for
inspection. The damaged item must remain available for inspection until the claim is finalized. In the event ITC requests to inspect the product, it agrees to dispatch its findings
pertaining to the alleged defective product within 45 days of receiving the product. Whenever claims are settled, ITC reserves the right to be subrogated under any existing
insurance policies the purchaser may have.
EVENTS THAT VOID WARRANTY All above warranties are null and void if any one or more of the following events occurs: (a) the item is not provided to ITC for inspection upon
ITC's request; (b) ITC determines that the item has been improperly installed, altered in any way or tampered with; (c) ITC determines that the item was not used under normal
operating conditions or in accordance with labels or instructions for the item including, (d) ITC determines the product was not properly maintained, and/or; e) ITC determines
that an unauthorized repair, modification, disassembly, or other changes to the product created the alleged defect. In addition to the foregoing, this Warranty does not
protect against damage to the product when ITC determines, in its sole discretion, that the damage resulted from acts of God such as lightning, flood, earthquake, war,
vandalism, theft, normal-use wear and tear, terrorism, strikes, and labor stoppages. This warranty specifically excludes damage, deterioration or discoloration caused by sunlight
or similar ultraviolet rays and/or wavelengths and/or dents, holes or scratches to the unit caused by stones, rocks, debris and/or vehicles.
Tape Light Installation Instructions
1.
Installing the track (Optional):
Determine the installation location of your tape lighting.
Once determined attach the clear plastic track using #4
wood screws (customer supplied). Note: The plastic track
needs to be pre-drilled. The track can also be glued in
place using an adhesive; however, the adhesive may
damage the surface if the track is ever removed.
2.
Installing the light:
The light can either be installed in a track or taped in place.
To install in a track, push the tape into one end of the
channel and then thumb down the other end. Note: Do not
remove the paper backing. To tape the light in place
remove the paper from the back of the light and press light
in place.
Tape Mount
Channel Mount
3.
Tape Light
Please note that the light is polarity sensitive. Connect the
red wire to the positive wire and the black wire to the ground
wire.
Red (+)
White (+)
Black (-)
12V
Power
Black (N)
230 E. Lakewood Blvd. • P.O. Box 8338 • Holland • MI • 49422-8338
Phone: 616-396-1355 • Fax: 616-396-1152 • www.elio-itc.com • sales@elio-itc.com • Revision 1: 10/18/11
Download PDF
Similar pages