C3758D4I-4L
C3558D4I-4L
User Manual
Version 1.0
Published November 2017
Copyright©2017 ASRock Rack INC. All rights reserved.
Version 1.1
Published December 2017
Copyright©2017 ASRock Rack Inc. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Rack Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished
for informational use only and subject to change without notice, and should not
be constructed as a commitment by ASRock Rack. ASRock Rack assumes no
responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock Rack does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock Rack, its directors, officers, employees, or agents be liable
for any indirect, special, incidental, or consequential damages (including damages
for loss of profits, loss of business, loss of data, interruption of business and the
like), even if ASRock Rack has been advised of the possibility of such damages
arising from any defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Rack’s Website: www.ASRockRack.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
Contact Information
If you need to contact ASRock Rack or want to know more about ASRock Rack,
you’re welcome to visit ASRock Rack’s website at www.ASRockRack.com; or you
may contact your dealer for further information.
ASRock Rack Incorporation
6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
Contents
Chapter 1 Introduction
1
1.1 1
Package Contents
1.2 Specifications
2
1.3 Unique Features
5
1.4 6
Motherboard Layout
1.5 Onboard LED Indicators
9
1.6 I/O Panel
10
1.7 Block Diagram
12
Chapter 2 Installation
13
2.1 13
Screw Holes
2.2 Pre-installation Precautions
13
2.3 Installation of Memory Modules (DIMM)
14
2.4 Expansion Slots (PCI Express Slot)
16
2.5 Jumper Setup
17
2.6 Onboard Headers and Connectors
19
2.7 Unit Identification purpose LED/Switch
25
2.8 Driver Installation Guide
25
2.9 Dual LAN and Teaming Operation Guide
26
Chapter 3 UEFI Setup Utility
27
3.1 27
Introduction
3.1.1 UEFI Menu Bar
27
3.1.2 Navigation Keys
28
3.2 Main Screen
29
3.3 Advanced Screen
30
3.3.1 CPU Configuration
31
3.3.2 DRAM Configuration
33
3.3.3 Chipset Configuration
34
3.3.4 Storage Configuration
36
3.3.5 ACPI Configuration
38
3.3.6 USB Configuration
39
3.3.7 Super IO Configuration
40
3.3.8 Serial Port Console Redirection
41
3.3.9 H/W Monitor
44
3.3.10 System Event Log
46
3.3.11 Intel SPS Configuration
48
3.3.12 Instant Flash
49
3.4 50
Security Screen
3.4.1 Secure Boot
51
3.4.2 Key Management
52
3.5 56
Boot Screen
3.5.1 CSM (Compatibility Support Module)
58
3.6 Event Logs Screen
59
3.7 Server Mgmt Screen
61
3.7.1 System Event Log
62
3.7.2 BMC Network Configuration
63
3.8 Exit Screen
65
Chapter 4 Software Support
66
4.1 66
Install Operating System 4.2 Support CD Information
66
4.2.1 Running The Support CD 66
4.2.2 Drivers Menu
66
4.2.3 Utilities Menu
66
4.2.4 Contact Information
66
Chapter 5 Troubleshooting
67
5.1 67
Troubleshooting Procedures
5.2 Technical Support Procedures
69
5.3 Returning Merchandise for Service
69
C3758D4I-4L / C3558D4I-4L
Chapter 1 Introduction
Thank you for purchasing ASRock Rack C3758D4I-4L / C3558D4I-4L motherboard,
a reliable motherboard produced under ASRock Rack’s consistently stringent quality
control. It delivers excellent performance with robust design conforming to ASRock
Rack’s commitment to quality and endurance.
In this manual, chapter 1 and 2 contains introduction of the motherboard and stepby-step guide to the hardware installation. Chapter 3 and 4 contains the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of
this manual occur, the updated version will be available on ASRock Rack website without
further notice. You may find the latest memory and CPU support lists on ASRock Rack
website as well. ASRock Rack’s Website: www.ASRockRack.com
If you require technical support related to this motherboard, please visit our website for
specific information about the model you are using.
http://www.asrockrack.com/support/
1.1 Package Contents
• ASRock Rack C3758D4I-4L / C3558D4I-4L Motherboard
(Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.02 cm x 17.02 cm)
• Support CD
• Quick Instllation Guide
• 1 x I/O Shield
• 2 x Mini SAS HD to 4 SAS/SATA Cables (12G)
• 2 x SATA3 Cables (6G) (60cm)
• 1 x SATA Power Cable (4PIN TO 15 PIN*6)
English
If any items are missing or appear damaged, contact your authorized dealer.
1
1.2 Specifications
C3758D4I-4L / C3558D4I-4L
MB Physical Status
Form Factor
Mini ITX
Dimension
6.7'' x 6.7'' (17.02 cm x 17.02 cm)
Processor System
CPU
C3758D4I-4L:
Intel® Atom C3758 Series Processor: 8core, 25W
C3558D4I-4L:
Intel® Atom C3558 Series Processor: 4core, 16W
Soc
Chipset
System Memory
Capacity
- 4 x 288-pin DDR4 DIMM slots
- Support up to 128GB DDR4 RDIMM (32 GB w/8Gb DRAM)
- Support up to 64GB DDR4 UDIMM (16 GB w/8Gb DRAM)
DIMM Sizes and - Dual Channel DDR4 memory technology
Type per DIMM - Non-ECC, ECC UDIMM: 4GB, 8GB, 16GB
- RDIMM: 4GB, 8GB, 16GB, 32GB
Frequency
- Non-ECC UDIMM: 1600/1866/2133/2400* MHz
- ECC UDIMM: 1600/1866/2133/2400* MHz
- RDIMM: 1600/1866/2133/2400* MHz
*Only C3758D4I-4L supports DDR4 up to 2400.
Voltage
Expansion Slot
PCIe 3.0 x8
Storage
1.2V
1 x PCIe MEx8 / EE x8 (MAX x8 by BIOS setup)
English
C3758D4I-4L:
13 x SATA3 6.0 Gb/s, 8x SATA ports from 2x mini SAS HD
connectors
SATA Controller
C3558D4I-4L:
5 x SATA3 6.0 Gb/s, 4x SATA ports from 1x mini SAS HD
connectors (Max 8 ports by BIOS setting)
Ethernet
Interface
Gigabit LAN 10/100/1000 Mb/s
LAN Controller - Marvell 88E1543(4L)
- Supports Wake-On-LAN
- Supports Energy Efficient Ethernet 802.3az
- Supports Dual LAN with Teaming function
- Supports PXE
- LAN1 Supports NCSI
2
C3758D4I-4L / C3558D4I-4L
Management
BMC Controller
ASPEED AST2500 : IPMI (Intelligent Platform Management
Interface) 2.0 with Ikvm and vMedia support
IPMI Dedicated
GLAN
1 x Realtek RTL8211E for dedicated management LAN
Features
- Watch Dog
- NMI
Gracphics
Controller
VRAM
Output
Rear Panel I/O
VGA Port
USB 3.0 Port
LAN Port
ASPEED AST2500
DDR4 64MB
Supports D-Sub with max. resolution up to 1920x1200 @ 60Hz
1 x D-sub
2
- 4 x RJ45 Gigabit Ethernet LAN ports
- 1 x RJ45 Dedicated IPMI LAN port
- LAN Ports with LED (ACT/LINK LED and SPEED LED)
UID Button/UID
1
LED
Serial port
1
Internal Connector
Auxiliary Panel 1 (includes chassis intrusion , location button & LED , front
Header
LAN LED, and event log LED)
TPM Header
1
IPMB Header
1
Fan Header
ATX Power
DC-IN
SATA POWER
Front Panel
USB 2.0 Header
System BIOS
BIOS Type
4 pins x4 (1CPU/2Front/1Rear)
1 (24-pin)
1 (8-pin) 12v
1 (4-pin)
1
1
English
128Mb AMI UEFI Legal BIOS
- Plug and Play (PnP)
- ACPI 1.1 Compliance Wake Up Events
BIOS Features
- SMBIOS 2.3.1 Support
- DRAM Voltage Multi-adjustment
- ASRock Instant Flash
Hardware Monitor
- CPU/PCH/DDR/LAN/Storage Temperature Sensing
Temperature
- MB/Card side/TR1 Temperature Sensing
3
Fan
Voltage
Support OS
OS
- CPU/Rear/Front Fan Tachometer
- CPU Quiet Fan (Allow CPU Fan Speed Auto-Adjust by CPU
Temperature)
- CPU/Rear/Front Fan Multi-Speed Control
Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
+BAT, 3VSB, 5VSB
Microsoft® Windows®
- Server 2016 (64 bit)
- Server 2012 (64 bit)
- Server 2012 R2 (64 bit)
Linux
- RedHat Enterprise Linux Server 6.8 (32 / 64 bit) / 7.2 (64 bit)
- CentOS 6.8 (32 / 64 bit) / 7.2 (64 bit)
- SUSE Enterprise Linux Server 11 SP4 (32 / 64 bit) / 12 SP1
(64 bit)
- Fedora core 24 (64 bit)
- Ubuntu 16.04 (64 bit) / 15.10 (64 bit) (AHCI mode)
Virtual
- VMWare ESXi 6.0
* Please refer to our website for the latest OS support list.
Environment
Temperature
Operation temperature: 10°C ~ 35°C / Non operation
temperature: -40°C ~ 70°C
* Install a CPU Fan when the airflow through the heatsink is below 2CFM.
* For detailed product information, please visit our website: http://www.asrockrack.com
This motherboard supports Wake from on Board LAN. To use this function, please make
sure that the “Wake on Magic Packet from power off state” is enabled in Device Manager
> Intel® Ethernet Connection > Power Management. And the “PCI Devices Power On” is
enabled in UEFI SETUP UTILITY > Advanced > ACPI Configuration. After that, onboard
LAN1&2 can wake up S5 under OS.
English
If you install Intel® LAN utility or Marvell SATA utility, this motherboard may fail Windows® Hardware Quality Lab (WHQL) certification tests. If you install the drivers only, it
will pass the WHQL tests.
4
C3758D4I-4L / C3558D4I-4L
1.3 Unique Features
ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating
systems first like MS-DOS or Windows®. With this utility, you can press the <F6> key
during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock
Rack Instant Flash. Just launch this tool and save the new BIOS file to your USB flash
drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks
without preparing an additional floppy diskette or other complicated flash utility.
Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file
English
system.
5
1.4 Motherboard Layout
1
4
3
2
40
1
17.0cm (6.7 in)
17.0cm (6.7 in)
ATXPWR1
REAR_FAN1
TB 1
1
DC_IN12V1
PSU_SMB1
UID
DDR4_B1 ( DDR4, 64 bit, 288-pin module, Blue)
5
DDR4_B2 ( DDR4, 64 bit, 288-pin module, White)
CMOS
Battery
6
DDR4_A1 ( DDR4, 64 bit, 288-pin module, Blue)
39
38
DDR4_A2 ( DDR4, 64 bit, 288-pin module, White)
HDD_PWR1
COM1
VGA1
1
ME_RECOVERY1
1
BMC_DIS1
1
CHASSIS_ID1
1
CHASSIS_ID2
7
FRNT_FAN1
CHASSIS_ID3
1
SATA_4_7
LAN1
13
SATA_8_11
SATA_PWR2
LAN4
SATA_12
SATA_0
SATA_PWR1
SATA_1
IPMI
LAN
SATA_2
SATA_3
USB_1_2
1
CLRMOS1
NMI_BTN1
1
1
LED_LAN3_4
T R1
1
1
IPMB1
BMC_SMB_1
1
SPEAKER1
FRNT_FAN2
AUX_PANEL1
PCIE7
(ME x8, EE x8)
34
English
6
33
1
32 31
TPMS1
30
1
1
PANEL1
29
14
15
16
17
18
19
20
1
BMC
AST2500
USB_SEL2
USB_SEL1
BIOS
ROM
USB 3.0
T: USB2
B: USB1
12
LAN2
Marvell
1543
LAN3
10
11
SATA_SGPIO2
C3758
C3558
36
35
8
9
CPU1_FAN1
SATA_SGPIO1
37
28
21
22
23
24
25
26
27
C3758D4I-4L / C3558D4I-4L
Description
1
PSU SMBus (PSU_SMB1)
2
Rear Fan Connector (REAR_FAN1)
3
ATX Power Connector (ATXPWR1)*
4
ATX 12V Power Connector (DC_IN12V1)*
5
2 x 288-pin DDR4 DIMM Slots (DDR4_A1 DDR4_B1)
6
2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
7
HDD Power Connector (HDD_PWR1)
8
CPU Fan Connector (CPU1_FAN1)
9
Front Fan Connector (FRNT_FAN1)
10
SATA SGPIO Connector (SATA_SGPIO1)
11
Mini SAS HD Connector (SATA_4_7)
12
SATA SGPIO Connector (SATA_SGPIO2)
13
Mini SAS HD Connector (SATA_8_11)
14
SATA DOM Power Jumper (SATA_PWR1)
15
SATA3 DOM Connector (SATA_12), Red
16
SATA3 DOM Connector (SATA_0), Red
17
SATA DOM Power Jumper (SATA_PWR1)
18
USB Selection Jumper (USB_SEL2)
19
USB Selection Jumper (USB_SEL1)
20
USB 2.0 Header (USB_1_2)**
21
Clear CMOS Pad (CLRMOS1)
22
Non Maskable Interrupt Button (NMI_BTN1)
23
LAN LED Connector (LED_LAN3_4)
24
Thermal Sensor Header (TR1)
25
Front Fan Connector (FRNT_FAN2)
26
Speaker Header (SPEAKER1)
27
BMC SMB Header (BMC_SMB1)
28
System Panel Header (PANEL1)
29
Auxiliary Panel Header (AUX_PANEL1)
30
TPMS Header (TPMS1)
31
Intelligent Platform Management Bus header (IPMB1)
32
SATA3 Connector (SATA_3), White
33
SATA3 Connector (SATA_2), White
English
No.
7
No.
Description
34
SATA3 Connector (SATA_1), White
35
Chassis ID Jumper (CHASSIS_ID3)
36
Chassis ID Jumper (CHASSIS_ID2)
37
Chassis ID Jumper (CHASSIS_ID1)
38
Enable/Disable BMC Jumper (BMC_DIS1)
39
ME Recovery Jumper (ME_RECOVERY1)
40
Thunderbolt AIC Connector (TB1)
*Please use either the ATX 12V Power Connector (DC_IN12V1) or the ATX Power Connector (ATXPWR1) at one
time. Do not connect them both simutaneously.
** The USB3_2 port on the rear I/O is shared with the USB_1_2 header on the motherboard. Please refer to p.18
for jumper setup information.
English
8
C3758D4I-4L / C3558D4I-4L
1.5 Onboard LED Indicators
1
1
ATXPWR1
1
REAR_FAN1_LED1
UID
DDR4_B1 ( DDR4, 64 bit, 288-pin module, Blue)
DDR4_B2 ( DDR4, 64 bit, 288-pin module, White)
CMOS
Battery
DDR4_A1 ( DDR4, 64 bit, 288-pin module, Blue)
DDR4_A2 ( DDR4, 64 bit, 288-pin module, White)
1
1
2
CPU1_FAN1_LED1
1
COM1
VGA1
1
3
1
FRNT_FAN1_LED1
C3758
C3558
LAN1
LAN2
Marvell
1543
LAN3
LAN4
BMC_LED1
BIOS
ROM
USB 3.0
T: USB2
B: USB1
IPMI
LAN
1
BMC
AST2500
1
1
1
1
1
4
1
FRNT_FAN2_LED1
PCIE7
1
1
1
5
Status
Description
1
Amber
REAR_FAN1 failed
2
Amber
CPU1_FAN1 failed
3
Amber
FRNT_FAN1 failed
4
Amber
FRNT_FAN2 failed
5
Green
BMC heartbeat LED
English
No.
9
1.6 I/O Panel
2
1
3
4
6
8
5
7
9
No. Description
No. Description
1
UID Switch (UID)
6
LAN RJ-45 Port (LAN4)**
2
COM Port (COM1)
7
LAN RJ-45 Port (LAN3)**
3
VGA Port (VGA1)
8
Dedicated IPMI LAN Port*
4
LAN RJ-45 Port (LAN2)**
9
USB 3.0 Ports (USB3_12)***
5
LAN RJ-45 Port (LAN1)**
LAN Port LED Indications
*There are two LED next to the LAN port. Please refer to the table below for the LAN port
LED indications.
ACT/LINK LED
SPEED LED
LAN Port
Dedicated IPMI LAN Port LED Indications
English
10
Activity / Link LED
Speed LED
Status
Description
Status
Description
Off
Blinking Yellow
On
No Link
Data Activity
Link
Off
Off
Yellow
Green
No Link
10M bps connection
100M bps connection
1G bps connection
C3758D4I-4L / C3558D4I-4L
**There are two LEDs on each LAN port. Please refer to the table below for the LAN port
LED indications.
SPEED LED
ACT/LINK LED
LAN Port
LAN Port (LAN1, LAN2, LAN3, LAN4) LED Indications
Speed LED
Activity / Link LED
Status
Description
Status
Description
Off
10Mbps connection or
no link
100Mbps connection
1Gbps connection
Off
No Link
Blinking Green
On
Data Activity
Link
Yellow
Green
English
*** The USB3_2 port on the rear I/O is shared with the USB_1_2 header on the
motherboard. Please refer to p.18 for jumper setup information.
11
PCIe slot7
PCIe x4/x8
DDR4 ChannelA
DDR4 1600/1866/2133
BIOS option
1.7 Block Diagram
C3758/3558D4I-4L
Mini-ITX
DDR4 ChannelB
DDR4 1600/1866/2133
SATA3 6G x4
SATA3 6G x4
1G
SATA3 6G x5
Intel Processor
Denverton SoC
C3000
SGMII
Marvell
88E1543
1G
1G
1G
Front USB2.0 Header
USB2.0 Port1
USB 2.0
USB2.0 Port2
USB_SEL1
USB_SEL2
Select by 2 jumpers
PCIe x1
USB3.0 Port1
USB 3.0
RGMII
Realtek
8211E
USB 2.0
USB3.0 Port2
TPM
Header
LPC
BMC
AST2500
VGA
UART
NCSI
TACH/PWM
SIO
NCT5573
UART
System FAN Header
CPU x1
Front x2
Rear x1
English
12
COM port
Header
C3758D4I-4L / C3558D4I-4L
Chapter 2 Installation
This is a Mini-ITX form factor (6.7'' x 6.7'', 17.0 cm x 17.0 cm) motherboard. Before
you install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits into it.
Make sure to unplug the power cord before installing or removing the motherboard. Failure
to do so may cause physical injuries to you and damages to motherboard components.
2.1 Screw Holes
Place screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components or
change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the motherboard’s components due to static electricity, NEVER
place your motherboard directly on the carpet or the like. Also remember to use a
grounded wrist strap or touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in
the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard to the chassis,
please do not over-tighten the screws! Doing so may damage the motherboard.
English
Before you install or remove any component, ensure that the power is switched off or the
power cord is detached from the power supply. Failure to do so may cause severe damage to
the motherboard, peripherals, and/or components.
13
2.3 Installation of Memory Modules (DIMM)
This motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and
supports Dual Channel Memory Technology.
1. For dual channel configuration, you always need to install identical (the same brand,
speed, size and chip-type) DDR4 DIMM pairs.
2. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot;
otherwise, this motherboard and DIMM may be damaged.
3. Please install the memory module on CH0_A1 for the first priority.
4. To activate Dual Channel Memory Technology, please follow the “Dual Channel Memory
Configuration” table below.
Dual Channel Memory Configuration
Priority
DDR4_A1
(Blue)
1
Populated
2
Populated
DDR4_A21
(White)
DDR4_B1
(Blue)
DDR4_B2
(White)
Populated
Populated
Populated
Populated
*Since installing three memory modules is NOT supported on this motherboard, we suggest not using
this configuration.
The DIMM only fits in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
English
14
C3758D4I-4L / C3558D4I-4L
1
2
English
3
15
2.4 Expansion Slots (PCI Express Slot)
There is 1 PCI Express slot on this motherboard.
PCIE slot:
PCIE7 (PCIE 3.0 x8 slot) is used for PCI Express max x8 lane width cards.
Slot
Generation
PCIE 7
Mechanical
3.0
x8
Electrical
x8 / x4
Source
CPU
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6. English
16
Before installing an expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the system unit cover (if your motherboard is already installed
in a chassis).
Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with screws.
Replace the system cover.
C3758D4I-4L / C3558D4I-4L
2.5 Jumper Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Chassis ID1 Jumper
(3-pin CHASSIS_ID1)
(see p.6, No. 37)
Chassis ID2 Jumper
(3-pin CHASSIS_ID2)
(see p.6, No. 38)
Chassis ID3 Jumper
(3-pin CHASSIS_ID3)
(see p.6, No. 35)
ME Recovery Mode
Single mother board indication (Default )
System level
Enable/Disable BMC
Jumper
(3-pin BMC_DIS1)
(see p.6, No. 38)
Normal Mode (Default)
BMC Enabled
BMC Disabled
SATA DOM Power
Jumper 1
(3-pin SATA_PWR1)
(see p.6, No. 17)
SATA DOM (SATA_0)
requires 5V power supply
Normal SATA (Default)
SATA DOM (SATA_0) does
NOT require 5V power
supply
English
ME Recovery Jumper
(3-pin ME_RECOVERY1)
(see p.6, No. 39)
Normal Mode (Default)
17
SATA DOM Power
Jumper 2
(3-pin SATA_PWR2)
(see p.6, No. 14)
USB Selection Jumpers
(3-pin USB_SEL1)
(see p.6, No. 19)
(3-pin USB_SEL2)
(see p.6, No. 18)
English
18
SATA DOM (SATA_12)
requires 5V power supply
Normal SATA (Default)
SATA DOM (SATA_12)
does NOT require 5V power
supply
1. USB3_2 on the Rear I/O
supports USB3.0 and USB2.0.
2. USB_1_2 header supports
Port 1 only.
(Default)
1. USB3_2 on the Rear I/O
supports USB3.0 only.
2. USB_1_2 header supports
Port 1 and Port 2.
C3758D4I-4L / C3558D4I-4L
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
headers and connectors. Placing jumper caps over the headers and connectors will cause
permanent damage to the motherboard.
*Please refer to page 6 or 8 for the motherboard layout.
These Mini SAS HD
connectors support SAS/SATA
data cables for internal storage
devices. The current SAS3/
SATA3 interface allows up to
12.0 Gb/s data transfer rate.
For connecting SAS HDDs,
please contact SAS data cable
dealers.
SATA_4_7
SATA_8_11
Serial ATA3 Connectors
(SATA_0)
(see p.6, No. 16)
(SATA_1)
(see p.6, No. 34)
(SATA_2)
(see p.6, No. 33)
(SATA_3)
(see p.6, No. 32)
SA TA_1
SA TA_2
SA TA_3
Serial ATA3 DOM
Connector
(SATA_0)
(see p.6, No. 16)
(SATA_12)
(see p.6, No. 15)
Chassis Speaker Header
(4-pin SPEAKER1)
(see p.6, No. 26)
These four SATA3
connectors support
SATA data cables for
internal storage devices
with up to 6.0 Gb/s data
transfer rate.
SA TA_0
SA TA_0
SA TA_12
DUMMY SPEAKER
1
+5V
DUMMY
The SATA3 DOM
connector supports
both a SATA DOM
(Disk-On-Module) and
a SATA data cable for
internal storage device.
Please connect the chassis
speaker to this header.
English
Mini SAS HD
Connectors*
(SATA_4_7)
(see p.6, No. 11)
(SATA_8_11)
(see p.6, No. 13)
19
GND
S_PWRDWN#
GND
+3V
LAD0
SERIRQ#
LAD2
LAD1
LAD3
SMB_CLK_MAIN
SMB_DATA_MAIN
GND
FRAME
PCIRST#
TPMS Header
(17-pin TPMS1)
(see p.6, No. 30)
Serial General Purpose
Input/Output Headers
(7-pin SATA_SGPIO1)
(see p.6, No. 10)
(7-pin SATA_SGPIO2)
(see p.6, No. 12)
PSU SMBus
(PSU_SMB1)
(see p.6, No. 1)
GND
+3VSB
PCICLK
1
SCLOCK
SLOAD
GND
GND
SDATAOUT
1
ALERT
+3V
SMBCLK
1
SMBDATA
GND
This connector supports Trusted Platform Module (TPM)
system, which can securely
store keys, digital certificates,
passwords, and data. A TPM
system also helps enhance
network security, protects
digital identities, and ensures
platform integrity.
These headers support Serial
Link interface for onboard
SATA connections.
PSU SMBus monitors the
status of the power supply, fan
and system temperature.
BMC_SMBDATA
BMC SMB Headers
(5-pin BMC_SMB_1)
(see p.6, No. 27)
Non Maskable Interrupt
Button Header
(2-pin NMI_BTN1)
(see p.6, No. 22)
English
20
GND
BMC_SMBCLK
Power
This header is used for the SM
BUS devices.
BMC_SMB_PRESENT_1_N
GND
1
CONTROL
Please connect a NMI device to
this header.
C3758D4I-4L / C3558D4I-4L
System Panel Header
(9-pin PANEL1)
(see p.6, No. 28)
This header accommodates
several system front panel
functions.
PLED+
PLEDPWRBTN#
GND
1
GND
RESET#
GND
HDLEDHDLED+
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may configure the way to turn
off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart the
computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is on when the
system is operating. The LED is off when the system is in powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is on when the
hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the
pin assignments are matched correctly.
12
13
24
GND
5V
5V
5V
N/A
GND
GND
GND
PSON#
GND
-12V
+12V
1
4
5
8
Please connect an ATX power
supply to this connector.
Though this motherboard
provides a 24-pin ATX power
connector, it can still work if
you adopt a traditional 20pin ATX power supply. To use
a 20-pin ATX power supply,
please plug your power supply
along Pin 1 and Pin 13.
This motherboard provides
one 8-pin ATX 12V power
connector.
English
3V
12V
12V
5VSB
GND
PWROK_PS
5V
GND
5V
GND
1
3V
ATX 12V Power
Connector
(8-pin DC_IN12V1)
(see p.6, No. 4)
3V
3V
ATX Power Connector
(24-pin ATXPWR1)
(see p.6, No. 3)
GND
21
LED_PWR
LAN2_LINK
System_Fault_LED_P
System_Fault_LED_N
LAN1_LINK
LED_PWR
GND
+3VSB
LOCATORLED-
GND
B
SMB_SMBDATA1
A
LOCATORLED+
BMC_Alert1_N
BMC_SMBCLK1
Auxiliary Panel Header
(18-pin AUX_PANEL1)
(see p.6, No. 29)
This header supports multiple
functions on the front panel,
including front panel SMB,
internet status indicator.
C
LOCATORBTN#
GND
CASEOPEN#
+5VSB
1
D
E
A. Front panel SMBus connecting pin (6-1 pin FPSMB)
This header allows you to connect SMBus (System Management Bus) equipment. It can
be used for communication between peripheral equipment in the system, which has slower
transmission rates, and power management equipment.
B. Internet status indicator (2-pin LAN1_LED, LAN2_LED)
These two 2-pin headers allow you to use the Gigabit internet indicator cable to connect
to the LAN status indicator. When this indicator flickers, it means that the internet is properly connected.
C. Chassis intrusion pin (2-pin CHASSIS)
This header is provided for host computer chassis with chassis intrusion detection designs.
In addition, it must also work with external detection equipment, such as a chassis intrusion detection sensor or a microswitch. When this function is activated, if any chassis
component movement occurs, the sensor will immediately detect it and send a signal to this
header, and the system will then record this chassis intrusion event. The default setting is
set to the CASEOPEN and GND pin; this function is off.
D. Locator LED (4-pin LOCATOR)
This header is for the locator switch and LED on the front panel.
E. System Fault LED (2-pin LOCATOR)
This header is for the Fault LED on the system.
Front and Rear
Fan Connectors
English
(4-pin FRNT_FAN1)
(see p.6, No. 9)
(4-pin FRNT_FAN2)
(see p.6, No. 25)
(4-pin REAR_FAN1)
(see p.6, No. 2)
22
FAN_SPEED_CONTROL
FAN_SPEED
FAN_VOLTAGE
GND
1
2
3
4
Please connect the fan cables to
the fan connectors and match
the black wire to the ground
pin. All fans supports Fan
Control.
C3758D4I-4L / C3558D4I-4L
CPU Fan Connector
(4-pin CPU1_FAN1)
(see p.6, No. 8)
FAN_VOLTAGE
CPU_FAN_SPEED
GND
FAN_SPEED_CONTROL
1
2
3
4
Please connect the CPU fan
cable to the connector and
match the black wire to the
ground pin.
Though this motherboard
provides a 4-Pin CPU fan
(Quiet Fan) connector, 3-Pin
CPU fans can still work
successfully even without the
fan speed control function.
If you plan to connect a
3-Pin CPU fan to the CPU
fan connector on this
motherboard, please connect
it to Pin 1-3.
*For more details, please refer to the
Cooler QVL list on the ASRock Rack
website.
2
+5V
GND
+12V
1
Intelligent Platform
Management Bus header
(4-pin IPMB1)
(see p.6, No. 31)
4
No connect
Please connect a 4-pin power
cable to this connector to
connect a HDD.
3
GND
IPMB_SCL
IPMB_SDA
This 4-pin connector is used
to provide a cabled baseboard
or front panel connection for
value added features and 3rdparty add-in cards, such as
Emergency Management cards,
that provide management
features using the IPMB.
English
HDD Power Connector
(4-pin HDD_PWR1)
(see p.6, No. 7)
23
LAN3_LINK
LED_PWR
LED_PWR
LAN4_LINK
LAN LED Connector
(LED_LAN3_4)
(see p.6, No. 23)
1
Thermal Sensor Header
(3-pin TR1)
(see p.6, No. 24)
TR1
TR1
1
GND
Clear CMOS Pad
(CLRMOS1)
(see p.6, No. 21)
for the front LAN status
indicator.
Please connect the thermal
sensor cable to either pin 1-2
or pin 2-3 and the other end to
the device which you wish to
monitor its temperature.
CLRMOS1 allows you to clear
the data in CMOS. To clear
CMOS, take out the CMOS
battery and short the Clear
CMOS Pad.
Thunderbolt AIC
Connector
(5-pin TB1)
(see p.6, No. 40)
Please connect a Thunderbolt™
add-in card (AIC) to this
connector via the GPIO cable.
1
The USB3_2 port on the rear I/O is
shared with the USB_1_2 header on
the motherboard. Please refer to p.18
for jumper setup information.
USB_PWR
-B
+B
USB 2.0 Header
(19-pin USB_1_2)
(see p.6, No. 20)
GND
DUMMY
1
GND
+A
-A
USB_PWR
English
24
This 4-pin connector is used
There is one USB 2.0 header on
this motherboard. This USB 2.0
header can support two USB
2.0 ports.
C3758D4I-4L / C3558D4I-4L
2.7 Unit Identification purpose LED/Switch
With the UID button, You are able to locate the server you’re working on from behind
a rack of servers.
Unit Identification
purpose LED/Switch
(UID1)
When the UID button on the
front or rear panel is pressed,
the front/rear UID blue LED
indicator will be turned on.
Press the UID button again to
turn off the indicator.
2.8 Driver Installation Guide
English
To install the drivers to your system, please insert the support CD to your optical
drive first. Then, the drivers compatible to your system can be auto-detected and listed
on the support CD driver page. Please follow the order from top to bottom to install
those required drivers. Therefore, the drivers you install can work properly.
25
2.9 Dual LAN and Teaming Operation Guide
Dual LAN with Teaming enabled on this motherboard allows two single
connections to act as one single connection for twice the transmission bandwidth,
making data transmission more effective and improving the quality of transmission
of distant images. Fault tolerance on the dual LAN network prevents network
downtime by transferring the workload from a failed port to a working port.
The speed of transmission is subject to the actual network environment or status even with
Teaming enabled.
Before setting up Teaming, please make sure whether your Switch (or Router)
supports Teaming (IEEE 802.3ad Link Aggregation). You can specify a preferred
adapter in Intel PROSet. Under normal conditions, the Primary adapter handles all
non-TCP/IP traffic. The Secondary adapter will receive fallback traffic if the primary
fails. If the Preferred Primary adapter fails, but is later restored to an active status,
control is automatically switched back to the Preferred Primary adapter.
Step 1
From Device Manager, open the properties of a team.
Step 2
Click the Settings tab.
Step 3
Click the Modify Team button.
Step 4
Select the adapter you want to be the primary adapter and click the Set Primary
button.
If you do not specify a preferred primary adapter, the software will choose an
adapter of the highest capability (model and speed) to act as the default primary. If
a failover occurs, another adapter becomes the primary. The adapter will, however,
rejoin the team as a non-primary.
English
26
C3758D4I-4L / C3558D4I-4L
Chapter 3 UEFI Setup Utility
3.1 Introduction
Th is section explains how to use the UEFI SETUP UTILITY to configure your system. The
UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI
SETUP UTILITY when you start up the computer. Please press <F2> or <Del> during the
Power-On-Self-Test (POST) to enter the UEFI SETUP UTILITY; otherwise, POST will
continue with its test routines.
If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by pressing
<Ctrl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may
also restart by turning the system off and then back on.
Because the UEFI software is constantly being updated, the following UEFI setup screens
and descriptions are for reference purpose only, and they may not exactly match what you
see on your screen.
3.1.1 UEFI Menu Bar
The top of the screen has a menu bar with the following selections:
Item
Description
Main
To set up the system time/date information
Advanced
To set up the advanced UEFI features
Security
To set up the security features
Boot
To set up the default system device to locate and load the
Operating System
Event Logs
For event log configuration
Server Mgmt
To manage the server
Exit
To exit the current screen or the UEFI SETUP UTILITY
English
Use < > key or < > key to choose among the selections on the menu bar, and
then press <Enter> to get into the sub screen.
27
3.1.2 Navigation Keys
Please check the following table for the function description of each navigation key.
Navigation Key(s)
English
28
Function Description
/
Moves cursor left or right to select Screens
/
Moves cursor up or down to select items
+ / -
To change option for the selected items
<Tab>
Switch to next function
<Enter>
To bring up the selected screen
<PGUP>
Go to the previous page
<PGDN>
Go to the next page
<HOME>
Go to the top of the screen
<END>
Go to the bottom of the screen
<F1>
To display the General Help Screen
<F7>
Discard changes and exit the UEFI SETUP UTILITY
<F9>
Load optimal default values for all the settings
<F10>
Save changes and exit the UEFI SETUP UTILITY
<F12>
Print screen
<ESC>
Jump to the Exit Screen or exit the current screen
C3758D4I-4L / C3558D4I-4L
3.2 Main Screen
Once you enter the UEFI SETUP UTILITY, the Main screen will appear and display the
English
system overview. The Main screen provides system overview information and allows you
to set the system time and date.
29
3.3 Advanced Screen
In this section, you may set the configurations for the following items: CPU Configuration,
DRAM Configuration, Chipset Configuration, Storage Configuration, ACPI Configuration, USB Configuration, Super IO Configuration, Serial Port Console Redirection, H/W
Monitor, System Event Log, Intel SPS Configuration and Instant Flash.
Setting wrong values in this section may cause the system to malfunction.
English
30
C3758D4I-4L / C3558D4I-4L
3.3.1 CPU Configuration
Intel SpeedStep Technology
Intel SpeedStep technology is Intel’s new power saving technology. Processors can switch
between multiple frequencies and voltage points to enable power saving. The default value
is [Enabled]. Configuration options: [Enabled] and [Disabled]. This item will be hidden if
the current CPU does not support Intel SpeedStep technology.
Please note that enabling this function may reduce CPU voltage and lead to system stability
or compatibility issues with some power supplies. Please set this item to [Disabled] if above
issues occur.
Active Processor Cores
Select the number of cores to enable in each processor package.
No-Execute Memory Protection
Processors with No-Execution Memory Protection Technology may prevent certain classes
English
of malicious buffer overflow attacks.
Intel Virtualization Technology
Intel Virtualization Technology allows a platform to run multiple operating systems
and applications in independent partitions, so that one computer system can function as
multiple virtual systems.
31
DCU Streamer Prefetcher
DCU streamer prefetcher is an L1 data cache prefetcher (MSR 1A4h [2]).
Hardware Prefetcher
Automatically prefetch data and code for the processor. Enable for better performance.
CPU C States Support
Enable CPU C States Support for power saving. It is recommended to keep C3, C6
and C7 all enabled for better power saving.
Package C State Support
Enable CPU, PCIe, Memory, Graphics C State Support for power saving.
Max Core C-State
Options are C1 and C6.
Enhanced Halt State(C1E)
Enable Enhanced Halt State (C1E) for lower power consumption.
AES-NI
Use this item to enable or disable AES-NI support.
CPU Thermal Throttling
Enable CPU internal thermal control mechanisms to keep the CPU from overheating.
English
32
C3758D4I-4L / C3558D4I-4L
3.3.2 DRAM Configuration
Fast Boot
Enables/Disables fast boot which skips memory training and attempts to boot using last
known good configuration.
Memory Test
Enable/Disables MRC test that writes and reads certain regions of memory and stresses
then through the use of the Converged Pattern Generation and Checking (CPGC) engine
in order to verify if the memory operation is healthy.
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s) inserted and
assign the appropriate frequency automatically.
ECC Support
English
Use this item to enable or disable DDR ECC Support.
33
3.3.3 Chipset Configuration
Switch Board Configuration
Select configuration of board.
C3758D4I-4L
Config 1: PCIE7 x8, SATA_0-7
Config 2: PCIE7 x4, SATA_0-12
C3558D4I-4L
Config 1: PCIE7 x4, SATA_0-3 and 12
Config 2: PCIE7 x4, SATA_4-7
Config 3: PCIE7 x4, SATA_8-12
Config 4: PCIE7 x8, SATA_12
Config 5: SATA_0-7 and SATA_12
Config 6: SATA_4-12
Config 7: SATA_0-3 and SATA_8-12
Above 4G Decoding
Enable or disable 64bit capable Devices to be decoded in Above 4G Address Space (only if
the system supports 64 bit PCI decoding).
Primary Graphics Adapter
English
If PCI Express graphics card is installed on the motherboard, you may use this option to
select PCI Express , Onboard VGA or Onboard Hdmi as the primary graphics adapter.
*If no PCI Express graphics card is installed, [Onboard VGA] is the default graphics adapter. There is no screen
on monitor even if a HDMI display is connected. Select [Onboard Hdmi] instead to use HDMI as output source.
34
C3758D4I-4L / C3558D4I-4L
Onboard VGA
Use this to enable or disable the Onboard VGA function. The default value is [Auto].
*This item is not available when the Primary Graphic Adapter is set to [Onboard VGA] or [Onboard Hdmi] .
VT-d
Intel Virtualization Technology for Directed I/O helps your virtual machine monitor better utilize hardware by improving application compatibility and reliability, and providing
additional levels of manageability, security, isolation, and I/O performance.
PCIE7 ASPM Support
This option enables or disables the ASPM support for all CPU downstream devices.
PCIE 7 Link Speed
This allows you to select PCIE 7 Link Speed. The default value is [Auto].
SR-IOV Support
If system has SR-IOV capable PCIe Devices, this option Enables or Disables Single Root IO
Virtualization Support.
Restore on AC Power Loss
This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is
selected, the AC/power remains off when the power recovers. If [Power On] is selected, the
AC/power resumes and the system starts to boot up when the power recovers. If [Last State]
English
is selected, it will recover to the state before AC/power loss.
35
3.3.4 Storage Configuration
Hard Disk S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting
Technology) feature. Configuration options: [Disabled] and [Enabled].
SATA Controller 0
Use this item to enable or disable the SATA controller 0 for SATA_0 to SATA_3 and
SATA_8 to SATA_11.
SATA AHCI LPM
Use this item to enable or disable Link Power Management. It is only supported by AHCI
mode for SATA_0 to SATA_3 and SATA_8 to SATA_11.
SATA SGPIO1
Enables SATA SGPIO1 function. It Enabled SATA SGPIO please insert jumper to J5.
SATA Controller 1
English
Use this item to enable or disable the SATA controller 1 for SATA_4 to SATA_7 and
SATA_12.
SATA AHCI LPM
Use this item to enable or disable Link Power Management. It is only supported by AHCI
36
C3758D4I-4L / C3558D4I-4L
mode for SATA_4 to SATA_7 and SATA_12.
SATA SGPIO2
English
Enables SATA SGPIO2 function. It Enabled SATA SGPIO please insert jumper to J6.
37
3.3.5 ACPI Configuration
PCIE Devices Power On
Use this item to enable or disable PCIE devices to turn on the system from the power-softoff mode.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system from the powersoft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the system.
English
38
C3758D4I-4L / C3558D4I-4L
3.3.6 USB Configuration
Legacy USB Support
Enable or disable Legacy OS Suppor t for USB 2.0 dev ices. If you encounter USB
compatibility issues, it is recommended to disable legacy USB support. Select UEFI Setup
Only to support USB devices under the UEFI setup and Window/Linux operating sustems
English
only.
39
3.3.7 Super IO Configuration
Serial Port 1 Configuration
Use this item to set parameters of Serial Port 1 (COM1).
Serial Port
Use this item to enable or disable the serial port.
Serial Port Address
Use this item to select an optimal setting for Super IO device.
SOL Configuration
Use this item to set SOL configuration.
SOL Port
Use this item to enable or disable the SOL port.
SOL Port Address
Use this item to select an optimal setting for Super IO device.
English
40
C3758D4I-4L / C3558D4I-4L
3.3.8 Serial Port Console Redirection
COM1 / SOL
Console Redirection
Use this option to enable or disable Console Redirection. If this item is set to Enabled, you
can select a COM Port to be used for Console Redirection.
Console Redirection Settings
Use this option to configure Console Redirection Settings, and specify how your computer
and the host computer to which you are connected exchange information. Both computers
should hhave the same or compatible settings.
Terminal Type
Option
Description
VT100
VT100+
VT-UTF8
ANSI
ASCII character set
Extended VT100 that supports color and function keys
UTF8 encoding is used to map Unicode chars onto 1 or more bytes
Extended ASCII character set
English
Use this item to select the preferred terminal emulation type for out-of-band management.
It is recommended to select [VT-UTF8].
41
Bits Per Second
Use this item to select the serial port transmission speed. The speed used in the host
computer and the client computer must be the same. Long or noisy lines may require lower
transmission speed. The options include [9600], [19200], [38400], [57600] and [115200].
Data Bits
Use this item to set the data transmission size. The options include [7] and [8] (Bits).
Parity
Use this item to select the parity bit. The options include [None], [Even], [Odd], [Mark] and
[Space].
Stop Bits
The item indicates the end of a serial data packet. The standard setting is [1] Stop Bit. Select
[2] Stop Bits for slower devices.
Flow Control
Use this item to set the f low control to prevent data loss from buffer overf low. When
sending data, if the receiving buffers are full, a "stop" signal can be sent to stop the data
flow. Once the buffers are empty, a "start" signal can be sent to restart the flow. Hardware
flow uses two wires to send start/stop signals. The options include [None] and [Hardware
RTS/CTS].
VT-UTF8 Combo Key Support
Use this item to enable or disable the VT-UTF8 Combo Key Support for ANSI/VT100
terminals.
Recorder Mode
Use this item to enable or disable Recorder Mode to capture terminal data and send it as
text messages.
Resolution 100x31
Use this item to enable or disable extended terminal resolution support.
Putty Keypad
Use this item to select Function Key and Keypad on Putty.
Legacy Console Redirection
Legacy Console Redirection Settings
Use this option to configure Legacy Console Redirection Settings, and specify how your
computer and the host computer to which you are connected exchange information.
English
Redirection COM Port
Use this item to select a COM port to display redirection of Legacy OS and Legacy OPROM
Messages.
Resolution
Use this item to select the number of rows and columns used in legacy OS redirection.
42
C3758D4I-4L / C3558D4I-4L
Redirection After BIOS POST
If the [Bootloader] is selected, legacy console redirection is disabled before booting to
legacy OS. If [Always Enabled] is selected, legacy console redirection is enabled for legacy
OS. The default value is [Always Enabled].
Serial Port for Out-of-Band Management/Windows Emergency
Management Services (EMS)
Console Redirection
Use this option to enable or disable Console Redirection. If this item is set to Enabled, you
can select a COM Port to be used for Console Redirection.
Console Redirection Settings
Use this option to configure Console Redirection Settings, and specify how your computer
and the host computer to which you are connected exchange information.
Out-of-Band Mgmt Port
Microsoft Windows Emergency Management Services (EMS) allows for remote
management of a Windows Server OS through a serial port.
Terminal Type
Use this item to select the preferred terminal emulation type for out-of-band management.
It is recommended to select [VT-UTF8].
Option
Description
VT100
VT100+
VT-UTF8
ANSI
ASCII character set
Extended VT100 that supports color and function keys
UTF8 encoding is used to map Unicode chars onto 1 or more bytes
Extended ASCII character set
Bits Per Second
Use this item to select the serial port transmission speed. The speed used in the host
computer and the client computer must be the same. Long or noisy lines may require lower
transmission speed. The options include [9600], [19200], [57600] and [115200].
Flow Control
Use this item to set the f low control to prevent data loss from buffer overf low. When
sending data, if the receiving buffers are full, a "stop" signal can be sent to stop the data
flow. Once the buffers are empty, a "start" signal can be sent to restart the flow. Hardware
flow uses two wires to send start/stop signals. The options include [None], [Hardware RTS/
CTS], and [Software Xon/Xoff].
English
Data Bits
Parity
Stop Bits
43
3.3.9 H/W Monitor
In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed,
chassis fan speed, and the critical voltage.
Fan Control
If [Auto] is selected, the fan speed will controlled by BMC.
If [Manual] is selected, configure the items below.
CPU1_FAN1
This allows you to set the CPU fan1’s speed. The default value is [Smart Fan].
REAR_FAN 1
This allows you to set the rear fan 1’s speed. The default value is [Smart Fan].
FRNT_FAN 1
This allows you to set the front fan 1’s speed. The default value is [Smart Fan].
FRNT_FAN 2
English
This allows you to set the front fan 2’s speed. The default value is [Smart Fan].
Smart Fan Control
This allows you to set the Smart fan’s level speed.
44
C3758D4I-4L / C3558D4I-4L
Smart Fan Duty Control
Smart Fan Duty x (x means 1 to 11 stage)
This allows you to set duty cycle for each stage.
Smart Fan Temp Control
Smart Fan Temp x (x means 1 to 11 stage)
This allows you to set temperature for each stage.
Watch Dog Timer
English
This allows you to enable or disable the Watch Dog Timer. The default value is [Disabled].
45
3.3.10 System Event Log
System Errors
System Error Enable/Disable/Auto setup options. If Auto is selected, the enabling or
disablinf of errors in the driver is skipped.
Memory ELog Support
Use this item to enable or disable Memory Error logging support.
Log Correctable Errors
Use this item to enable or disable Correctable Mermory Error logging support.
Log Un-Correctable Errors
Use this item to enable or disable Un-Correctable Memory Error logging support.
PCIe ELog Support
Use this item to enable or disable PCIe Error logging support.
Log Fatal Error
English
Use this item to enable or disable sending system event Signal on Fatal error.
Log Non-Fatal Error
Use this item to enable or disable sending system event Signal on Non Fatal error.
46
C3758D4I-4L / C3558D4I-4L
Log Correctable Error
Use this item to enable or disable sending system event Signal on Correctable error
Whea Suuport
English
Use this item to enable or disable Windows Hardware Error Architecture.
47
3.3.11 Intel SPS Configuration
ME Subsystem screen displays the Intel ME Subsystem Configuration information, such
as Operational Firmware Version and Firmware State.
English
48
C3758D4I-4L / C3558D4I-4L
3.3.12 Instant Flash
English
Instant Flash is a UEFI flash utility embedded in Flash ROM. This convenient UEFI
update tool allows you to update system UEFI without entering operating systems
first like MS-DOS or Windows®. Just save the new UEFI file to your USB flash drive,
floppy disk or hard drive and launch this tool, then you can update your UEFI only
in a few clicks without preparing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use
FAT32/16/12 file system. If you execute Instant Flash utility, the utility will show the
UEFI files and their respective information. Select the proper UEFI file to update
your UEFI, and reboot your system after the UEFI update process is completed.
49
3.4 Security Screen
In this section, you may set or change the supervisor/user password for the system. For the
user password, you may also clear it.
Supervisor Password
Set or change the password for the administrator account. Only the administrator
has authority to change the settings in the UEFI Setup Utility. Leave it blank and
press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to change the
settings in the UEFI Setup Utility. Leave it blank and press enter to remove the
password.
English
50
C3758D4I-4L / C3558D4I-4L
3.4.1 Secure Boot
Secure Boot
Enable to support Windows 8 or later version Secure Boot.
Secure Boot Mode
English
Secure Boot mode selector: Standard/Custom. In Custom mode, Secure Boot Variables can be configured without authentication.
51
3.4.2 Key Management
In this section, expert users can modify Secure Boot Policy variables without full authentication.
Provision Factory Defaults
Allow to provision factory default Secure Boot keys when System is in Setup Mode.
Install Default Secure Boot Keys
Please install default secure boot keys if it’s the first time you use secure boot.
Clear Secure Boot keys
Force System to Setup Mode - clear all Secure Boot Variables. Change takes effect
after reboot.
Enroll Efi Image
Allow the image to run in Secure Boot mode. Enroll SHA256 hash of the binary
into Authorized Signature Database (db).
English
Save all Secure Boot variables
Save NVRAM content of Secure Boot policy variables to the files (EFI_SIGNATURE_LIST data format) in root folder on a target file system device.
52
C3758D4I-4L / C3558D4I-4L
Platform Key(PK)
Enroll Factory Defaults or load certificates from a file:
1. Public Key Certificate in:
a) EFI_SIGNATURE_LIST
b) EFI_CERT_X509 (DER encoded)
c) EFI_CERT_RSA2048 (bin)
d) EFI_CERT_SHA256, 384, 512
2. Authenticated UEFI Variable
3. EFI PE/COFF Image(SHA256)
Key Source: Default, External, Mixed, Test
Key Exchange Keys
Enroll Factory Defaults or load certificates from a file:
1. Public Key Certificate in:
a) EFI_SIGNATURE_LIST
b) EFI_CERT_X509 (DER encoded)
c) EFI_CERT_RSA2048 (bin)
d) EFI_CERT_SHA256, 384, 512
2. Authenticated UEFI Variable
3. EFI PE/COFF Image(SHA256)
Key Source: Default, External, Mixed, Test
Authorized Signatures
Enroll Factory Defaults or load certificates from a file:
1. Public Key Certificate in:
a) EFI_SIGNATURE_LIST
English
b) EFI_CERT_X509 (DER encoded)
c) EFI_CERT_RSA2048 (bin)
d) EFI_CERT_SHA256, 384, 512
53
2. Authenticated UEFI Variable
3. EFI PE/COFF Image(SHA256)
Key Source: Default, External, Mixed, Test
Forbidden Signatures
Enroll Factory Defaults or load certificates from a file:
1. Public Key Certificate in:
a) EFI_SIGNATURE_LIST
b) EFI_CERT_X509 (DER encoded)
c) EFI_CERT_RSA2048 (bin)
d) EFI_CERT_SHA256, 384, 512
2. Authenticated UEFI Variable
3. EFI PE/COFF Image(SHA256)
Key Source: Default, External, Mixed, Test
Authorized TimeStamps
Enroll Factory Defaults or load certificates from a file:
1. Public Key Certificate in:
a) EFI_SIGNATURE_LIST
b) EFI_CERT_X509 (DER encoded)
c) EFI_CERT_RSA2048 (bin)
d) EFI_CERT_SHA256, 384, 512
2. Authenticated UEFI Variable
3. EFI PE/COFF Image(SHA256)
Key Source: Default, External, Mixed, Test
OsRecovery Signatures
English
Enroll Factory Defaults or load certificates from a file:
1. Public Key Certificate in:
a) EFI_SIGNATURE_LIST
54
C3758D4I-4L / C3558D4I-4L
b) EFI_CERT_X509 (DER encoded)
c) EFI_CERT_RSA2048 (bin)
d) EFI_CERT_SHA256, 384, 512
2. Authenticated UEFI Variable
3. EFI PE/COFF Image(SHA256)
English
Key Source: Default, External, Mixed, Test
55
3.5 Boot Screen
In this section, it will display the available devices on your system for you to configure the
boot settings and the boot priority.
Boot Option Priorities
Boot Option #1
Use this item to set the system boot order.
Boot Option #2
Use this item to set the system boot order.
Boot Option #3
Use this item to set the system boot order.
Boot Option Filter
This option controls Legacy/UEFI ROMs priority.
English
USB Device BBS Priorities
Use this item to set the system boot order from USB devices.
Boot From Onboard LAN
Use this item to enable or disable the Boot From Onboard LAN feature.
56
C3758D4I-4L / C3558D4I-4L
Setup Prompt Timeout
This shows the number of seconds to wait for setup activation key. 65535(0XFFFF) means
indefinite waiting.
Bootup Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock function after
boot-up.
Boot Beep
Select whether the Boot Beep should be turned on or off when the system boots up. Please
note that a buzzer is needed.
Full Screen Logo
Use this item to enable or disable OEM Logo. The default value is [Enabled].
AddOn ROM Display
English
Use this option to adjust AddOn ROM Display. If you enable the option “Full Screen Logo”
but you want to see the AddOn ROM information when the system boots, please select
[Enabled]. Configuration options: [Enabled] and [Disabled]. The default value is [Enabled].
57
3.5.1 CSM(Compatibility Support Module)
CSM
Enable to launch the Compatibility Support Module. Please do not disable unless
you’re running a WHCK test. If you are using Windows 8.1 64-bit and all of your
devices support UEFI, you may also disable CSM for faster boot speed.
Items below vary depending on the CSM option.
Launch Video OpROM Policy
Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
PCIE7 Slot OpROM
This option controls Legacy/UEFI ROMs priority.
English
58
C3758D4I-4L / C3558D4I-4L
3.6 Event Logs Screen
Change Smbios Event Log Settings
This allows you to configure the Smbios Event Log Settings.
When entering the item, you will see the followings:
Smbios Event Log
Use this item to enable or disable all features of the SMBIOS Event Logging during system
boot.
Erase Event Log
The options include [No], [Yes, Next reset] and [Yes, Every reset]. If Yes is selected, all
logged events will be erased.
When Log is Full
Use this item to choose options for reactions to a full Smbios Event Log. The options
include [Do Nothing] and [Erase Immediately].
MECI (Multiple Event Count Increment)
English
Use this item to enter the increment value for the multiple event counter. The valid range is
from 1 to 255.
METW (Multiple Event Time Window)
Use this item to specify the number of minutes which must pass between duplicate log
entries which utilize a multiple-event counter. The value ranges from 0 to 99 minutes.
59
View Smbios Event Log
Press <Enter> to view the Smbios Event Log records.
All values changed here do not take effect until computer is restarted.
English
60
C3758D4I-4L / C3558D4I-4L
3.7 Server Mgmt Screen
Wait For BMC
Wait For BMC response for specified time out. In PILOTII, BMC starts at the same time
when BIOS starts during AC power ON. It takes around 30 seconds to initialize Host to
English
BMC interfaces.
61
3.7.1 System Event Log
SEL Components
Change this to enable ro disable all features of System Event Logging during boot.
Erase SEL
Use this to choose options for earsing SEL.
When SEL is Full
Use this to choose options for reactions to a full SEL.
Log EFI Status Codes
Use this item to disable the logging of EFI Status Codes or log only error code or only
progress or both.
English
62
C3758D4I-4L / C3558D4I-4L
3.7.2 BMC Network Configuration
Lan Channel (Failover)
Manual Setting IPMI LAN
If [No] is selected, the IP address is assigned by DHCP. If you prefer using a static IP
address, toggle to [Yes], and the changes take effect after the system reboots. The default
value is [No].
Configuration Address Source
Select to configure BMC network parameters statically or dynamically(by BIOS or BMC).
Configuration options: [Static] and [DHCP].
Static: Manually enter the IP Address, Subnet Mask and Gateway Address in the BIOS for
BMC LAN channel configuration.
DHCP: IP address, Subnet Mask and Gateway Address are automatically assigned by the
network's DHCP server.
English
When [DHCP] or [Static] is selected, do NOT modify the BMC network settings on the
IPMI web page.
63
The default login information for the IPMI web interface is:
Username: admin
Password: admin
For more instructions on how to set up remote control environment and use the IPMI management platform, please refer to the IPMI Configuration User Guide or go to the Support
website at: http://www.asrockrack.com/support/ipmi.asp
English
64
C3758D4I-4L / C3558D4I-4L
3.8 Exit Screen
Save Changes and Exit
When you select this option, the following message “Save configuration changes and exit
setup?” will pop-out. Press <F10> key or select [Yes] to save the changes and exit the UEFI
SETUP UTILITY.
Discard Changes and Exit
When you select this option, the following message “Discard changes and exit setup?” will
pop-out. Press <ESC> key or select [Yes] to exit the UEFI SETUP UTILITY without saving
any changes.
Discard Changes
When you select this option, the following message “Discard changes?” will pop-out. Press
<F7> key or select [Yes] to discard all changes.
Load UEFI Defaults
Load UEFI default values for all the setup questions. F9 key can be used for this operation.
English
Boot Override
These items displays the available devices. Select an item to start booting from the selected
device.
65
Chapter 4 Software Support
4.1 Install Operating System
This motherboard supports Microsoft® Windows® Server 2008 R2 SP1 (64 bit) / 2012 (64
bit) / Linux compliant. Because motherboard settings and hardware options vary, use the
setup procedures in this chapter for general reference only. Refer your OS documentation
for more information.
4.2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and useful
utilities that enhance the motherboard’s features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the
Main Menu does not appear automatically, locate and double click on the file “ASRSetup.
exe” from the root folder in the Support CD to display the menu.
4.2.2 Drivers Menu
The Drivers Menu shows the available device’s drivers if the system detects installed
devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the application softwares that the motherboard supports. Click
on a specific item then follow the installation wizard to install it.
4.2.4 Contact Information
If you need to contact ASRock Rack or want to know more about ASRock Rack, welcome
to visit ASRock Rack’s website at http://www.ASRockRack.com; or you may contact your
dealer for further information.
English
66
C3758D4I-4L / C3558D4I-4L
Chapter 5 Troubleshooting
5.1 Troubleshooting Procedures
Follow the procedures below to troubleshoot your system.
Always unplug the power cord before adding, removing or changing any hardware components. Failure to do so may cause physical injuries to you and damages to motherboard
components.
1. Disconnect the power cable and check whether the PWR LED is off.
2. Unplug all cables, connectors and remove all add-on cards from the motherboard.
Make sure that the jumpers are set to default settings.
3. Confirm that there are no short circuits between the motherboard and the chassis.
4. Install a CPU and fan on the motherboard, then connect the chassis speaker and power
LED.
If there is no power...
1.
2.
3.
4.
Confirm that there are no short circuits between the motherboard and the chassis.
Make sure that the jumpers are set to default settings.
Check the settings of the 115V/230V switch on the power supply.
Verify if the battery on the motherboard provides ~3VDC. Install a new battery if it
does not.
If there is no video...
1. Try replugging the monitor cables and power cord.
2. Check for memory errors.
If there are memory errors...
English
1. Verify that the DIMM modules are properly seated in the slots.
2. Use recommended DDR3 1600/1333/1066 non ECC, unbuffered DIMMs.
3. If you have installed more than one DIMM modules, they should be identical with the
same brand, speed, size and chip-type.
4. Try inserting different DIMM modules into different slots to identify faulty ones.
5. Check the settings of the 115V/230V switch on the power supply.
67
Unable to save system setup configurations...
1. Verify if the battery on the motherboard provides ~3VDC. Install a new battery if it
does not.
2. Confirm whether your power supply provides adaquate and stable power.
Other problems...
1. Try searching keywords related to your problem on ASRock Rack’s FAQ page:
http://www.asrockrack.com/support
English
68
C3758D4I-4L / C3558D4I-4L
5.2 Technical Support Procedures
If you have tried the troubleshooting procedures mentioned above and the problems
are still unsolved, please contact ASRock Rack’s technical support with the following
information:
1.
2.
3.
4.
Your contact information
Model name, BIOS version and problem type
System configuration
Problem description
You may contact ASRock Rack’s technical support at:
http://www.asrockrack.com/support/tsd.asp
5.3 Returning Merchandise for Service
For warranty service, the receipt or a copy of your invoice marked with the date of
purchase is required. By calling your vendor or going to our RMA website (http://event.
asrockrack.com/tsd.asp) you may obtain a Returned Merchandise Authorization (RMA)
number.
The RMA number should be displayed on the outside of the shipping carton which is
mailed prepaid or hand-carried when you return the motherboard to the manufacturer.
Shipping and handling charges will be applied for all orders that must be mailed when
service is complete.
This warranty does not cover damages incurred in shipping or from failure due to
alteration, misuse, abuse or improper maintenance of products.
English
Contact your distributor first for any product related problems during the warranty period.
69
Download PDF
Similar pages