Multifunction board, optically isolated, 16/8 SE or 8/4

Multifunction board, optically isolated,
16/8 SE or 8/4 diff. inputs, 4 analog outputs, 12-/16-bit
APCI-3110 / APCI-3116
PCI 3.3 V or 5 V
Optical isolation 1000 V
16/8 SE or 8/4 diff. inputs
12-bit or 16-bit resolution, 200 kHz
PCI DMA, programmable gain
4 analog outputs, 12-bit
Timer/counter/watchdog
8 optically isolated dig. I/O, 24 V, 24 TTL I/O
Features
Safety features
• PCI 3.3 V or 5 V
• O
ptical isolation 1000 V min.
• Creeping distance IEC 61010-1
• Circuit part of the analog acquisition is separated from
the circuit part of the digital function
• Overvoltage protection ± 40 V
• Protection against high-frequency EMI
• Input filters
• Noise neutralisation of the PC supply
• Connection of the I/O signals through robust industrystandard­D-Sub connector
Analog inputs
32-bit
•
•
•
•
6/8 SE or 8/4 diff. inputs, optically isolated
1
Resolution: 12-bit (APCI-3110) or 16-bit (APCI-3116)
Throughput: 200 kHz
Input voltage: 0-10 V, ±10 V, 0-5 V, ±5 V, 0-2 V, ±2 V,
0-1 V, ±1 V, 0-20 mA (option), freely programmable
through software for each channel
• Current inputs: 0-20 mA (Option)
can be combined freely with voltage inputs
• Gain PGA x1, x2, x5, x10 freely programmable through
software for each channel
Analog acquisition
Signed 64-bit drivers for
Windows 7/XP
• D
ifferent input modes:
1) Simple mode
2) Scan modes
3) Sequence modes
4) Auto Refresh mode
• Onboard FIFO (for 512 analog values)
• PCI-DMA for analog data acquisition
Analog outputs
LabVIEWTM
LabWindows/CVITM
•
•
•
•
•
analog outputs, optically isolated
4
12-bit resolution
Setup time 15 µs typ
Output voltage after reset: 0 V
Each output has its own ground line (without optical
isolation)
• Output voltage range: -10 V up to + 10 V
• Output current: ± 5 mA
• Short-circuit current: ± 20 mA
24 V digital I/O
• 2
4 V digital I/O enable a high interference distance and
a long distance between signal transmitter and data
acquisition
• 4 digital inputs, 24 V, optically isolated
• 4 digital outputs, 24 V, optically isolated
TTL I/O
Customer-tailored
modifications
designed
to suit your needs.
Hardware and software,
firmware, PLDs, ...
Contact us!
•
•
•
•
4 digital TTL inputs/outputs
2
Port0: outputs / Port1: inputs / Port2: I/O
All I/O are at 5 V through pull-up resistors
Easy programming through I/O read and write
commands
•
•
•
•
•
•
•
•
•
Industrial process control
Industrial measurement and monitoring
Multichannel data acquisition
Control of chemical processes
Factory automation
Acquisition of sensor data
Laboratory equipment
Current measurement
Instrumentation
Software
Standard drivers for:
•
•
•
•
Linux
32-bit drivers for Windows 8 / 7 / Vista / XP / 2000
Signed 64-bit drivers for Windows 8 / 7 / XP
Real-time use with Linux and Windows on request
Drivers and samples for the following compilers and
software packages:
• .NET
• Microsoft VC++ • Borland C++ • Visual Basic
• Delphi • LabVIEW • LabWindows/CVI
ADDIPACK functions:
Analog input • Analog output • Digital input
Digital output • Watchdog • Timer • Counter
Timer/counter
On request:
• 3 / 3, 16-bit
Further operating systems, compilers and samples.
Watchdog
• 2, 16-bit
Phone: +49 7229 1847-0
Fax:
+49 7229 1847-222
Applications
info@addi-data.com
www.addi-data.com
Driver download: www.addi-data.com, download menu
PCI, analog – APCI-3110 / APCI-3116
Specifications
37-pin
D-Sub
connector
MUX
D/A
converter
A/D
converter
Gain
Isolation
Opto-couplers
Opto-couplers
DC/DC
converter
FPGA
control logic
Watchdog
Timer/counter
Sequ. RAM
FIFO
PCI
controller
24 TTL I/O
4 analog
outputs
4 dig. inputs, 24 V
4 dig. outputs, 24 V
Opto-couplers
16 SE/8 diff.
or
8 SE/4 diff.
inputs
Tiefpass filters
16/8 SE or 8/4 differential inputs
12-bit (APCI-3110) or 16-bit (APCI-3116)
1000 V through opto-couplers from PC to peripheral
Software-programmable for each channel
0-10 V, ±10 V, 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V
0-20 mA optional
Software programmable (x1, x2, x5, x10)
200 kHz
through software, timer, external event (24 V input)
Data to the PC through FIFO memory,
Interrupt at EOC (End Of Conversion),
DMA transfer at EOC
End of conversion, at timer overrun, End of scan
EMI filters
Number of inputs:
Resolution:
Optical isolation:
Input ranges:
Gain:
Throughput:
Trigger:
Data transfer:
Interrupts:
4 x dig. inputs
4 x dig. outputs
Simplified block diagram
Analog inputs
24
TTL
I/O
50-pin
male connector
PCI bus
Pin assignment – 37-pin D-Sub male connector
Analog outputs
Number of outputs:
Optical isolation:
Resolution:
Voltage outputs
Output range:
LSB: Accuracy: Time to Ready: Setup time: Max. output current:
Short-circuit current:
Output voltage after reset:
4
1000 V through opto-couplers
12-bit
-10 V to +10 V (-1 LSB)
4.8828 mV
11-bit
typ. 4.5 µs
typ 15 µs (at 10 V step)
± 5 mA
± 20 mA
0V
Digital I/O
Number of I/O channels:
Logical “0” level:
Logical “1” level:
Optical isolation:
4 digital inputs, 24 V
4 digital outputs, 24 V
0-14 V
19-30 V
1000 V through opto-couplers from PC to peripheral
TTL I/O
Number of TTL I/O channels:
I/O Address range:
Programming:
24
128 Byte, addressing : 32-bit
Through write/read commands
EMC – Electromagnetic compatibility
Pin assignment – 50-pin male connector
Assignment
Output 3
Input 3Input 2+
Output 1
Input 1Input 0+
GND 0
Not connected
GND
TTL 15
TTL 7
Assignment
TTL 22
TTL 13
TTL 5
TTL 20
TTL 11
TTL 3
TTL 18
TTL 9
TTL 1
TTL 16
Digital
Pin
31
33
35
37
39
41
43
45
47
49
32
34
36
38
40
42
44
46
48
50
Assignment
TTL 6
TTL 21
TTL 12
TTL 4
TTL 19
TTL 10
TTL 2
TTL 17
TTL 8
TTL 0
8 dig. I/O, 24 V
24 TTL I/O
ST370-16
PX8001
Physical and environmental conditions
175 x 99 mm
PCI 32-bit 3.3/5V acc. to spec. 2.2 (PCISiG)
1 PCI slot for analog I/O,
1 slot opening for digital I/O with FB8001
+5 V, ±5 % from the PC
37-pin D-Sub male connector
50-pin male connector for connecting the dig. I/O
0 to 60 °C (with forced cooling)
Assignment
Input 3+
Output 2
Input 2Input 1 +
Output 0
Input 0+24 V
Not connected
GND
TTL 23
TTL 14
ADDI-DATA connection
The product complies with the European EMC directive. The tests were carried out by
a certified EMC laboratory in accordance with the norm from the EN 61326 series (IEC
61326). The limit values as set out by the European EMC directive for an industrial
environment are complied with. The respective EMC test report is available on request.
Dimensions:
System bus:
Space required:
Operating voltage:
Front connector:
Additional connector :
Temperature range:
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 bis 24
25
26
27
28
29
30
FB8001
PX_BNC
PX901-AG
Analog
ST010/ST011
or
D-Sub
male
connector
Pin 1
APCI-3xxx
D-Sub
female
connector
50-pin
male connector
Ordering information
APCI-3110 / APCI-3116
Multifunction board, optically isolated, 16/8 SE or 8/4 diff. inputs, 4 analog outputs, 12-/16-bit.
Incl. technical description and software drivers.
Versions
APCI-3110-16:
APCI-3110-8:
APCI-3116-16:
APCI-3116-8:
Accessories
16 SE/8 diff. inputs, 4 analog outputs, 12-bit
8 SE/4 diff. inputs, 4 analog outputs, 12-bit
16 SE/8 diff. inputs, 4 analog outputs, 16-bit
8 SE/4 diff. inputs, 4 analog outputs, 16-bit
Options
Please indicate the number of channels
Option SF: Precision filter for 1 single-ended channel
Option DF: Precision filter for 1 diff. channel
Option PC: Current input 0(4)-20 mA for 1 channel
PC-SE: for Single-ended PC-Diff: for differential
PX901-A:
PX901-AG:
PX_BNC:
ST010:
ST011:
PX8001:
FB8001:
ST370-16:
Screw terminal panel with transorb diodes
for connecting the analog I/O
Same as PX901-A with housing for DIN rail
BNC connection box for connecting the analog I/O
Standard round cable, shielded, twisted pairs, 2 m
Standard round cable, shielded, twisted pairs, 5 m
3-row screw terminal panel, 50-pin, for DIN-rail mounting
Ribbon cable for digital I/O
Standard round cable, shielded, twisted pairs, 2 m
Phone: +49 7229 1847-0
Fax:
+49 7229 1847-222
info@addi-data.com
www.addi-data.com
Download PDF
Similar pages