Report No.: TRS17090131
Page 1 of 15
Issue: 2017-10-18
TEST REPORT
COMMISSION REGULATION (EU) No 617/2013 of 26 June 2013
implementing Directive 2009/125/EC of the European Parliament and of the Council with regard
to ecodesign requirements for computers and computer servers
Report No. ....................................... :
TRS17090131
Tested by (name and signature) ...... :
Jacky Chen
……………………………………
Reviewed by (name and signature) . :
Terry Wen
……………………………………
Approved by(name and signature)... :
Caroline Li
……………………………………
Date of issue .................................... :
2017-10-18
Total Pages ...................................... :
15 Pages
Testing Laboratory ........................... :
Shenzhen HuaTongWei International Inspection Co., Ltd.
Address ............................................ :
Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, S
Guangdong, China
Testing location/procedure ............... :
Shenzhen HuaTongWei International Inspection Co., Ltd.
Address ............................................ :
Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, S
Guangdong, China
R/C: 26035
Test specification ........................... :
Standard(s) ...................................... :
(EU) 617/2013:2013-06-26; (EC) 278/2009:2009-04-06
Test procedure ................................. :
BS EN 62623:2013; EN 50563:2011+A1:2013
Non-standard test method ............... :
N/A
Test item description ..................... :
Product name…………………………:
Tablet
Applicant name……………………….:
Applicant address…………………….:
Microtech Srl
Via Aldo Moro 9 20090 Buccinasco (MI) Italy
Manufacturer name………………….:
Microtech Srl
Manufacturer address…………….…:
Via Aldo Moro 9 20090 Buccinasco (MI) Italy
Trademark ........................................ :
e-tab
Model/Type reference ...................... :
e-tab_style_REV3
Input Rating(s) ................................. :
Units: 5Vd.c., 2.0A (Internal battery: 3.7V, 6000mAh)
AC Adapter: Input: 100-240Va.c., 50/60Hz, 0.5A;
Output: 5.0Vd.c., 2.0A
Report No.: TRS17090131
Page 2 of 15
Issue: 2017-10-18
Copy of marking plate
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
Lable of AC Adapter
Lable of Tablet
Summary of Testing:
The submitted samples were comply with the above standard.
Report No.: TRS17090131
Page 3 of 15
Issue: 2017-10-18
Test case verdicts……………………………………....:
Test case does not apply to the test object……….…..:
N(N/A)
Test item does meet the requirement………….……....:
P(Pass)
Test item does not meet the requirement……………..:
F(Fail)
Testing……………..………………………………….....:
Date of receipt of test item ……………………………..:
2017-09-13
Date(s) of performance of test………………………….:
2017-10-18
General Remarks:
This report shall not be reproduced except in full without the written approval of the testing laboratory.
The test results presented in this report relate only to the item(s) tested.
”(see remark #)" refers to a remark appended to the report.
"(see Annex #)" refers to an annex appended to the report.
Throughout this report a point is used as the decimal separator.
General product information:
1. The Tablet with input 5VDC/2A is supplied by external switching power adapter for general use
purpose.
2. The Tablet has a rechargeable Li-ion Polymer battery that can’t be replaced.
3. The testing was performed on model e-tab_style_REV3 with fully-charged battery pack.
4. The external switching power adapter complied with Efficiency Level V, which is certificated by
Shenzhen TCT Testing Technology Co., Ltd. (Report No. : TCT170918S004).
5. External switching power adapter information as follows:
Object
Manufacturer Name
Model
Rating
Comply with
Energy
Efficiency Level
AC ADAPTER
Shenzhen Xingheyuan
Technology Co., Ltd.
XHY050200UE
Input: AC100-240V,
50/60Hz, 0.5A;
Output: 5Vd.c., 2A
V
Report No.: TRS17090131
Page 4 of 15
Issue: 2017-10-18
TABLE: 1 - TEST EQUIPMENT LIST
NO
Name
Type
Equipment No.
Calibration date
Last
1
Comments
Due
1
Digital power
meter
WT210
HTWS0004
1 year
2018.04.25
Yokogawa
2
Power Quality
Analyzer
F43B
HTWS0073
1 year
2018.04.25
Fluke
3
Sound Level
Tester
DT-805
HTWS0139
1 year
2018.10.16
CEM
4
E-load
3710A
HTWS0212
1 year
2018-10-16
ARRAY
5
Anemometer
AM-4201
HTWS0152
1 year
2018-10-19
LUTRON
6
Luminance
Meter
LM-3
HTWS0292
1 year
2018-02-02
EVERFINE
7
Stopwatch
PC2008
HTWS0086
1 year
2018-04-25
CHAOSUDA
8
Temperature &
Humidity Meter
TT-492
HTWS0017-D
1 year
2018-04-25
JAPAN
9
Tape Measure
5M
HTWS0142
3 year
2018-05-06
ZHEJIANG
1) or interval between calibrations.
Report No.: TRS17090131
Page 5 of 15
Issue: 2017-10-18
1. General conditions for measurement
The air speed close to the UUT:
0.3 m/s (Requirement:≤0.5m/s)
The ambient temperature:
24.5°C ( Requirement:23°C±5°C)
The ambient light:
Test voltage and frequency:
280Lux (Requirement: 250 ±50lux)
230V/50Hz(Requirement:230V±1%/50Hz±1%)
5.0 VDC±1% for products drawing power from a computer USB
port
the midpoint of the rated input voltage range for all other products
(only on DC input voltage)
Input voltage Total Harmonic
Distortion(V%THD):
Crest factor of input voltage:
AC ripple voltage (RMS) (for DC input
voltage):
Sample size:
1.40(Requirement:1.34 – 1.49)
≤ 0.2 V for DC voltages up to 10 V; or
≤ 2 % of the DC voltage for DC voltages over 10 V
257 mm * 174 mm * 15 mm
Display size(in):
10.1
Display width resolution(pixels):
1920
Display height resolution(pixels):
1080
Noise level:
Refer to technical support by manufacturer
0.5 %(Requirement:≤ 2 % (up to and including the 13th harmonic))
Remark:
1. When determining for test conclusion, measurement uncertainty of tests has been considered.
2. Measurements of power of 0.50 W or greater was made with an uncertainty of less than or equal to 2 % at
the 95 % confidence level.
3. Measurements of power of less than 0.50 W was made with an uncertainty of less than or equal to 0.01 W
at the 95 % confidence level.
4. The power measurement instrument shall, as applicable, have a resolution of:
(1) 0.01 W or better for measurements up to 10 W;
(2) 0.1 W or better for measurements of 10 to 100 W; or
(3) 1 W or better for measurements over 100 W.
Report No.: TRS17090131
Page 6 of 15
Issue: 2017-10-18
2. Ecodesign requirements and timetable:
1. E TEC
Desktop computer and
integrated desktop
computer
1.1. From 1 July 2014:
1.1.1. The annual total energy consumption (E TEC in kWh/year) shall not exceed:
(a) Category A computer: 133.00;
(b) Category B computer: 158.00;
(c) Category C computer: 188.00;
(d) Category C computer: 211.00;
E TEC shall be determined using the following formula:
E TEC = (8 760/1 000) × (0.55 × P off + 0.05 × P sleep + 0.40 × P idle )
For computers that lack a discrete sleep mode, but have idle state power demand
less than or equal to 10,00 W, power in idle state (P idle ) may be used in
place of sleep (P sleep ) in the above equation, such that the formula is
replaced by
E TEC = (8 760/1 000) × (0.55 × P off + 0.45 × P idle )
All P x are power values in the indicated mode/state as defined in the definition
section, measured in Watts (W) according to the procedures indicated in
Annex III.
1.1.2. The following capability adjustments apply:
(a) memory: 1 kWh/year per GB over base, where base memory is 2 GB (for
category A, B and C computers) and 4 GB (for category D computers);;
(b) additional internal storage: 25 kWh/year;
(c) discrete television tuner: 15 kWh/year;
(d) discrete audio card: 15 kWh/year;
(e) discrete graphics card (dGfx) (for the first and each additional discrete graphics
card (dGfx)):
dGfx category
TEC allowance
(kWh/year)
First discrete graphics
card (dGfx)
Each additional discrete
graphics card (dGfx)
G1
34
G2
54
G3
69
G4
100
G5
133
G6
166
G7
225
G1
20
G2
32
G3
41
G4
59
G5
78
G6
98
G7
133
Report No.: TRS17090131
Page 7 of 15
Issue: 2017-10-18
1.1.3. The capability adjustments for discrete graphics cards (dGfx) and discrete
television tuner mentioned in point 1.1.2 and point 1.2.2 only apply to cards
and tuner that are enabled during testing of notebook computers.
1.1.4. Category D desktop computers and integrated desktop computers meeting
all of the following technical parameters are exempt from the provisions
specified in points 1.1.1 and 1.1.2 and their revisions specified in point 1.2:
(a) a minimum of six physical cores in the central processing unit (CPU); and
(b) discrete graphics card(s) (dGfx) providing total frame buffer bandwidths above
320 GB/s; and
(c) a minimum 16 GB of system memory; and
(d) a PSU with a rated output power of at least 1 000 W.
1.2. From 1 January 2016:
1.4.1. The following revisions to the annual total energy consumption specified in
point 1.1.1 apply:
The annual total energy consumption (E TEC in kWh/year) shall not exceed:
(a) Category A computer: 94.00;
(b) Category B computer: 112.00;
(c) Category C computer: 134.00;
(d) Category D computer: 150.00;
1.4.2. The following revisions to the capability adjustments for discrete graphics
card (dGfx) specified in point 1.1.2(e) apply:
dGfx category
TEC allowance
(kWh/year)
First discrete graphics
card (dGfx)
Each additional discrete
graphics card (dGfx)
G1
18
G2
30
G3
38
G4
54
G5
72
G6
90
G7
122
G1
11
G2
17
G3
22
G4
32
G5
42
G6
53
G7
72
Report No.: TRS17090131
Page 8 of 15
Issue: 2017-10-18
2. E TEC
Notebook computer
1.3. From 1 July 2014:
1.3.1. The annual total energy consumption (E TEC in kWh/year) shall not exceed:
(a) Category A computer: 36.00;
(b) Category B computer: 48.00;
(c) Category C computer: 80.50;
E TEC shall be determined using the following formula: E TEC = (8 760/1 000) × (0.60
× P off + 0.10 × P sleep + 0.30 × P idle ) where all P x are power values in the
indicated mode/state as defined in the definition section, measured in Watts (W)
according to the procedures indicated in Annex III.
1.3.2. The following capability adjustments apply:
(a) memory: 0.4 kWh/year per GB over base, where base memory is 4 GB;
(b) additional internal storage: 3 kWh/year;
(c) discrete television tuner: 2.1 kWh/year;
(d) discrete graphics card (dGfx) (for the first and each additional discrete
graphics card (dGfx)):
dGfx category
TEC allowance
(kWh/year)
First discrete graphics
card (dGfx)
Each additional discrete
graphics card (dGfx)
G1
12
G2
20
G3
26
G4
37
G5
49
G6
61
G7
113
G1
7
G2
12
G3
15
G4
22
G5
29
G6
36
G7
66
1.3.3. The capability adjustments for discrete graphics cards (dGfx) and discrete
television tuner mentioned in point 1.3.2 and point 1.4.2 only apply to cards and
tuner that are enabled during testing of notebook computers.
1.3.4. Category C notebook computers meeting all of the following technical
parameters are exempt from the provisions specified in points 1.3.1 and 1.3.2 and
their revisions specified in point 1.4:
(a) a minimum of four physical cores in the central processing unit (CPU); and
(b) discrete graphics card(s) (dGfx) providing total frame buffer bandwidths above
225 GB/s; and
(c) a minimum 16 GB of system memory.
Report No.: TRS17090131
Page 9 of 15
Issue: 2017-10-18
1.4. From 1 January 2016:
1.4.1. The following revisions to the annual total energy consumption specified in
point 1.3.1 apply:
The annual total energy consumption (E TEC in kWh/year) shall not exceed:
(a) Category A computer: 27.00;
(b) Category B computer: 36.00;
(c) Category C computer: 60.50;
1.4.2. The following revisions to the capability adjustments for discrete graphics
First discrete graphics
card (dGfx)
Each additional discrete
graphics card (dGfx)
dGfx category
TEC allowance
(kWh/year)
G1
7
G2
11
G3
13
G4
20
G5
27
G6
33
G7
61
G1
4
G2
6
G3
8
G4
12
G5
16
G6
20
G7
36
card (dGfx) specified in point 1.3.2(d) apply:
2. SLEEP MODE
Desktop computer,
integrated desktop
computer and notebook
computer
2. From 1 July 2014:
2.1. A product shall provide sleep mode and/or another condition that provides the
functionality of sleep mode and which does not exceed the applicable power
demand requirements for a sleep mode.
2.2. Power demand in sleep mode shall not exceed 5.00 W in desktop computers
and integrated desktop computers and 3.00 W in notebook computers.
2.3. Desktop computers and integrated desktop computers where idle state power
demand is less than or equal to 10.00 W are not required to have a discrete
system sleep mode.
2.4. Where a product is placed on the market with a WOL functionality enabled in
sleep mode: (a) an additional allowance of 0.70 W can be applied; (b) it must be
tested with a WOL functionality both enabled and disabled and must comply with
both requirements.
2.5. Where a product is placed on the market without Ethernet capability, it shall
be tested without WOL enabled.
Report No.: TRS17090131
Page 10 of 15
Issue: 2017-10-18
3. LOWEST POWER STATE
Desktop computer,
integrated desktop
computer and notebook
computer
3. As of the entry into force of the Regulation:
3.1. Power demand in the lowest power state shall not exceed 0.50 W.
3.2. A product shall provide a power state or mode which does not exceed the
applicable power demand requirements for the lowest power state when it is
connected to the mains power source.
3.3. Where a product is placed on the market with an information or status display,
an additional allowance of 0.50 W can be applied.
4. OFF MODE
Desktop computer,
integrated desktop
computer and notebook
computer
4. From 1 July 2014:
4.1. Power demand in off mode shall not exceed 1.00 W.
4.2. A product shall provide off mode and/or another condition which does not
exceed the applicable power demand requirements for off mode when it is
connected to the mains power source.
4.3. Where a product is placed on the market with a WOL functionality enabled in
off mode: (a) an additional allowance of 0.70 W can be applied; (b) it must be
tested with a WOL functionality both enabled and disabled and must comply with
both requirements.
4.4. Where a product is placed on the market without Ethernet capability, it shall
be tested without WOL enabled.
6. POWER MANAGEMENT ENABLING
Desktop computer,
integrated desktop
computer and notebook
computer
6.1. As of the entry into force of the Regulation:
The computer shall offer a power management function, or a similar function
which, when the computer is not providing the main function or when other energyusing products are not dependent on its functions, automatically switches the
computer into a power mode that has a lower power demand than the applicable
power demand requirement for sleep mode.
6.2. From 1 July 2014:
6.2.1. The computer shall reduce the speed of any active 1 Gigabit per second
(Gb/s) Ethernet network links when transitioning to sleep or off-with-WOL mode.
6.2.2. When in sleep mode, the response to ‘wake events’, such as those via
network connections or user interface devices, should happen with a latency of ≤
5 seconds from the initiation of a wake event to the system becoming fully usable
including rendering of display.
6.2.3. The computer shall be placed on the market with the display sleep mode
set to activate within 10 minutes of user inactivity.
6.2.4. A computer with Ethernet capability shall have the ability to enable and
disable a WOL function, if available, for sleep mode. A computer with Ethernet
capability shall have the ability to enable and disable WOL for off mode if WOL
from off mode is supported.
6.2.5. Where a distinct sleep mode or another condition that provides sleep mode
functionality exists, the mode shall be set to activate within 30 minutes of user
inactivity. This power management function shall be activated before placing the
product on the market.
6.2.6. Users shall be able to easily activate and deactivate any wireless network
connection(s) and users shall be given a clear indication with a symbol, light or
equivalent, when wireless network connection(s) have been activated or
deactivated.
Report No.: TRS17090131
Page 11 of 15
Issue: 2017-10-18
3. Product information and test result:
1) Product information:
Notebook computer
Product type:
Desktop computer
Integrated desktop computer
Operating system:
Windows
Mac OS
Other: Android
Operating system version details:
Android 7
Processor
MT8163V/A
Category:
Category A
Memory:
2.00 GB
Additional internal storage:
Yes.
Discrete television tuner:
None.
Discrete graphics card (dGfx)
None.
Manufacturer’s name:
Microtech Srl
Address:
Via Aldo Moro 9 20090 Buccinasco (MI) Italy
Trade mark:
e-tab
Product model number:
e-tab_style_REV3
2) Battery information:
Battery chemistry:
Li-ion Polymer
Manufacturer of battery:
Shenzhen Power Tech International Co.,Ltd
Model of battery:
PL2666139P
Ratings of battery:
3.7 V, 6000 mAh, 22.2Wh
Min charge discharge cycle:
(For Notebook computer)
Number of batteries incorporated
in the product:
For notebook computer:
Battery pack removed during test:
If no then:
Fully charged battery pack used:
See battery specification
1
Yes
No
Yes
Note: The battery in this product cannot be easily replaced by users themselves.
Report No.: TRS17090131
Page 12 of 15
Issue: 2017-10-18
3) Power management feature:
1, Battery
2, Go to sleep
3, Wake for network access
4, Slightly dim the display
5, Timing shutdown
Click Battery, then select energy-saving options for that power source.
If you want to put your computer to sleep, please press the power button or
set the time to go to sleep.
Users can access your computer’s shared resources, such as shared
printers, even when your computer is in sleep mode.
Reduce the brightness of the display while on battery power, you can select
the automatic brightness options.
Set a daily schedule for turning it off and on.
4) Test result:
Power mode:
Recorded average Watts
Limited
Off mode (Poff)
0.88 W
< 1.00 W
Sleep mode (Psleep)
1.02 W
< 3.00 W
Idle mode (Pidle)
7.68 W
Lowest power mode (Plowest)
0.88 W
< 1.00 W
Active mode (Pwork)
9.10 W
--
20.18 kWh/year
≤ 27.00 kWh/year
E TEC = (8 760/1 000) × (0.60 × Poff +
0.10 × Psleep + 0.30 × Pidle )
≥ 6.00 W
(For Notebook computer)
Test condition:
Test voltage and frequency:
Total Harmonic Distortion:
230V / 50Hz
0.5 %
System sleep mode default time:
30 mins
Display sleep mode default time:
30 mins
External power supply Efficiency:
>75.43 %
Test methodology for power supply:
(EC) 278/2009:2009-04-06, EN 50563:2011+A1:2013
Report No.: TRS17090131
Page 13 of 15
Issue: 2017-10-18
ATTACHMENT - Photos of Product
Photo 1
General View
Photo 2
General View
Report No.: TRS17090131
Photo 3
Front View
Photo 4
Rear View
Page 14 of 15
Issue: 2017-10-18
Report No.: TRS17090131
Page 15 of 15
Photo 5
Switching Adaptor
View
-- END OF REPORT --
Issue: 2017-10-18
Download PDF
Similar pages