Dinion2X - Bosch Security Systems

Dinion2X
LTC0498 | LTC0630
en
Installation Manual
Dinion2X
Table of Contents | en
3
Table of Contents
1
Safety
5
1.1
Safety precautions
5
1.2
Important safety instructions
5
1.3
System ground/Safety ground
6
1.4
FCC information
7
2
Introduction
9
2.1
Features
9
3
Installation
11
3.1
Unpacking
11
4
Connection and mounting
13
4.1
Power connection
13
4.1.1
Low voltage cameras
13
4.1.2
High voltage cameras
14
4.2
Video connections
15
4.2.1
Output Video signal
15
4.2.2
Synchronization signal
15
4.3
Alarm and relay connector
16
4.4
Lens mounting
17
4.5
Back focus adjustment
18
4.6
Mounting the camera
19
5
Configuration
21
5.1
Menus
21
5.1.1
Top level menus
21
5.1.2
Menu navigation
21
5.2
Pre-defined modes
23
5.3
Day/Night switching
24
5.4
Camera control communication (Bilinx)
24
5.5
Main menu structure
25
5.5.1
Mode submenu
25
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0| 2009.03
4
en | Table of Contents
Dinion2X
5.5.2
ALC submenu
5.5.3
Shutter/AGC submenu
26
27
5.5.4
Day/Night submenu
28
5.5.5
Enhance / Dynamic Engine submenu
30
5.5.6
Color submenu
31
5.5.7
VMD submenu
32
5.6
Install menu structure
34
5.6.1
Language submenu
35
5.6.2
Lens Wizard submenu
35
5.6.3
Synchronization submenu
37
5.6.4
Alarm I/O submenu
37
5.6.5
Connections submenu
38
5.6.6
Test signal submenu
39
5.6.7
Camera ID submenu
40
5.6.8
Privacy masking submenu
40
5.6.9
Defaults submenu
41
6
Troubleshooting
43
6.1
Resolving problems
43
6.2
Customer service
43
7
Maintenance
45
7.1
Repairs
45
7.1.1
Transfer and disposal
45
8
Technical Data
47
8.1
Specifications
47
8.1.1
Dimensions
50
8.1.2
Accessories
51
Glossary
53
AR18-08-B013 | v1.0| 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Safety | en
1
Safety
1.1
Safety precautions
5
DANGER!
High risk: The lighting flash and arrowhead within the triangle is
a warning sign alerting you of "Dangerous Voltage" inside the
product that can cause an electrical shock, bodily injury, or
death.
!
!
1.2
WARNING!
Medium risk: The exclamation mark within the triangle sign
alerts the user to important instructions accompanying the unit.
CAUTION!
Low risk: Alerts the user to the risk of damage to the unit.
Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Follow all warnings on the unit and in the
operating instructions before operating the unit.
1.
Clean only with a dry cloth. Do not use liquid cleaners or
aerosol cleaners.
2.
Do not install unit near any heat sources such as radiators,
heaters, stoves, or other equipment (including amplifiers)
that produce heat.
3.
Never spill liquid of any kind on the unit.
4.
Take precautions to protect the unit from power and
5.
Adjust only those controls specified in the operating
lightning surges.
instructions.
6.
Operate the unit only from the type of power source
indicated on the label.
7.
Unless qualified, do not attempt to service a damaged unit
yourself. Refer all servicing to qualified service personnel.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
6
en | Safety
Dinion2X
8.
Use only replacement parts specified by the manufacturer.
9.
Install in accordance with the manufacturer's instructions
in accordance with applicable local codes. Use only
attachments/accessories specified by the manufacturer.
Equipment change or modification could void the user's
guarantee or authorization agreement.
WARNING!
Power disconnect for high voltage versions: A unit has power
!
supplied whenever the power cord is inserted into the power
source. The power cord plug is the main power disconnect for
the unit. For pluggable equipment, install the socket outlet near
the equipment so it is easily accessible.
WARNING!
!
All-pole power switch: Incorporate an all-pole power switch,
with a contact separation of at least 3 mm in each pole, into the
electrical installation of the building.
CAUTION!
!
Fuse rating: The branch circuit protection must be secured with
a maximum fuse rating of 16 A. This must be in accordance with
NEC800 (CEC Section 60).
CAUTION!
!
1.3
The Low Voltage power supply unit must comply with EN/UL
60950. The power supply must be a SELV-LPS unit or a SELV Class 2 unit (Safety Extra Low Voltage - Limited Power Source).
System ground/Safety ground
System (video) ground is indicated by the symbol
.
Safety (power) ground is indicated by the symbol
.
The system ground is only used to comply with safety standards
or installation practices in certain countries. Bosch does not
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Safety | en
7
recommend connecting system ground to safety ground unless
it is explicitly required. However, if the system ground and
safety ground are connected and grounding loops are causing
interference in the video signal, use an isolation transformer
(available separately from Bosch).
!
1.4
CAUTION!
Connecting System ground to Safety ground may result in
ground loops that can disrupt the CCTV system.
FCC information
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
–
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
–
Consult the dealer or an experienced radio/ TV technician
for help.
Note
Any change or modification of the equipment not expressly
approved by Bosch could void the user's authority to operate
the equipment.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
8
en | Safety
Dinion2X
Disposal - Your Bosch product was developed and
manufactured with high-quality material and components that
can be recycled and reused. This symbol means that
electronic and electrical appliances, which have reached the
end of their working life, must be collected and disposed of
separately from household waste material. Separate collecting
systems are usually in place for disused electronic and
electrical products. Please dispose of these units at an
environmentally compatible recycling facility, per European
Directive 2002/96/EC
For additional information or to speak to a representative,
please contact the Bosch Security Systems location nearest to
you or visit our web site at www.boschsecurity.com
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Introduction | en
2
Introduction
2.1
Features
9
The Dinion2X Day/Night camera is a high-performance, smart,
surveillance color camera. It incorporates advanced (20-bit)
digital signal processing and a wide dynamic range CCD sensor
for outstanding picture performance.
The Dinion2X camera is easy to install and ready to use, and
offers the best solution for demanding scene conditions.
Features include:
–
1/3-inch CCD sensor with wide dynamic range (LTC0498)
–
1/2-inch CCD sensor (LTC0630)
–
True Day/Night performance with switchable IR filter
–
540 TVL resolution
–
Dynamic engine with Smart BLC
–
Privacy zones
–
Autoblack
–
Bilinx (bi-directional coaxial communication)
–
Wide operating temperature range
–
Lens wizard
–
Lens autodetect
(-20 to +55 °C / -4 to +131 °F)
–
Six pre-programmed operation modes
–
Adaptive dynamic noise reduction
–
Genlock including subcarrier locking
–
Multiple language on-screen display
–
Built-in test pattern generator
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
10
en | Introduction
AR18-08-B013 | v1.0 | 2009.03
Dinion2X
Installation Manual
Bosch Security Systems
Dinion2X
Installation | en
3
Installation
3.1
Unpacking
11
Unpack carefully and handle the equipment with care.
The packaging contains:
–
Dinion2X Day/Night camera
–
CCD protection cap (mounted on camera)
–
Plastic bag containing:
–
Alarm I/O connector
–
Power connector
–
Spare lens connector (male)
–
Important safety instructions
–
Quick install instructions
–
CD ROM
–
Installation Instructions
–
Adobe Acrobat Reader
If equipment has been damaged during shipment, repack it in
the original packaging and notify the shipping agent or supplier.
WARNING!
!
!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code or
applicable local codes.
CAUTION!
The camera module is a sensitive device and must be handled
carefully.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
12
en | Installation
AR18-08-B013 | v1.0 | 2009.03
Dinion2X
Installation Manual
Bosch Security Systems
Dinion2X
4
Connection and mounting | en
13
Connection and mounting
CAUTION!
!
Before proceeding, disconnect the power from the power
supply cable. Ensure that the voltage of the unit matches the
voltage and type of the power supply being used.
4.1
Power connection
4.1.1
Low voltage cameras
SYNC
1
2
3
ALARM
4
5
6
+
12 VDC
24 VAC
VIDEO
5 mm
Figure 4.1
Low voltage power connection
Connect power from a 24 VAC or 12 VDC class 2 power supply
as follows:
–
Use AWG16 to 22 stranded wire or AWG16 to 26 solid
wire; cut back 5 mm (0.2 in) of insulation.
–
Remove the 3-pole connector from the camera body.
–
Loosen the screws and insert the wires.
Note
The central connection for System (video) ground is
optional. Connecting System ground to Safety ground may
result in ground loops that can disrupt the CCTV system.
–
Tighten the screws and reconnect the 3-pole connector to
the camera.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
14
en | Connection and mounting
Dinion2X
Note
For a DC supply the polarity is important. Incorrect polarity
does not damage the camera but it will not switch on.
For an AC supply maintain a consistent wiring polarity in
multiple camera systems to help avoid potential camera video
rolling.
4.1.2
High voltage cameras
SYNC
1
2
3
ALARM
4
5
6
VIDEO
Figure 4.2
High voltage power connection
Connect the power cable of a high voltage camera to either a
230 VAC or a 120 VAC power supply outlet depending on the
version.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
4.2
Connection and mounting | en
15
Video connections
SYNC
Sync BNC
1
2
3
ALARM
4
5
6
VIDEO
Video BNC
Figure 4.3
4.2.1
BNC connectors
Output Video signal
The camera has a BNC connector to connect the video coax
cable with a male BNC connector. A UTP adapter (VDA-455UTP)
is available as an optional accessory to allow a UTP video cable
to be connected to the BNC connector.
4.2.2
Synchronization signal
The camera has a BNC connector to accept a coax cable with a
male BNC connector for synchronization.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
16
en | Connection and mounting
4.3
Dinion2X
Alarm and relay connector
ALARM
1
4
2
5
3
6
Figure 4.4
Alarm and relay connector pins
Pin
Alarm socket
1
Alarm in ground
2
not used
3
Relay out contact 1
4
Alarm in 1
5
not used
6
Relay out contact 2
–
5 mm
(0.2 in)
Max. wire diameter AWG 22-28 for both stranded and
solid; cut back 5 mm (0.2 in) of insulation.
–
Alarm output relay switching capability: Max voltage 30VAC
or +40 VDC. Max 0.5 A continuous, 10 VA.
–
Alarm in: TTL logic, +5V nominal, +40 VDC max, DC coupled
with 22 kOhm pull-up to +3.3 V.
–
Alarm in: configurable as active low or active high.
–
Max. 42 V allowed between camera ground and each of the
relay pins.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
4.4
Connection and mounting | en
17
Lens mounting
The camera accepts CS-mount lenses. C-mount lenses can be
mounted using the lens adapter ring. DC-iris lenses are
recommended for the best picture performance. The camera
automatically detects the type of lens used and optimizes
performance accordingly. A spare male lens connector is
provided.
CAUTION!
To avoid damaging the CCD sensor when using a C-mount lens,
!
make sure the supplied lens adapter ring is mounted onto the
camera before mounting the lens.
Lenses weighing more than 0.5 kg (1.1lbs) must be separately
supported.
Bosch
Bosch
Figure 4.6
Figure 4.5 Mounting a lens
Pin
Video iris lens
DC iris lens
1
Supply (11.5V ±0.5, 50mA max.)
Damp -
2
Not used
Damp +
3
Video signal 1Vpp 1kOhm
Drive +
4
Ground
Drive -
Lens connector
Note
If a short circuit is detected on the lens connector, the onscreen display (OSD) failure message LENS SHORT CIRCUIT is
shown. The lens circuit is automatically disabled to avoid
internal damage. Remove the lens connector and check the pin
connections.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
18
en | Connection and mounting
4.5
Dinion2X
Back focus adjustment
To optimize picture sharpness in both bright and low-level
lighting, adjust the back focus. Use the camera's unique Lens
Wizard. This ensures that the object of interest always remains
in focus, even when focusing at the maximum lens iris opening
(for example, at night).
–
When back focusing varifocal lenses, adjust to obtain a
sharp picture in both wide-angle and tele positions for
both far and near focus.
–
When back focusing zoom lenses, ensure the object of
interest remains in focus throughout the entire zoom range
of the lens.
To adjust back focus:
1.
Open the slide door panel at the side of the camera.
Bos
ch
2.
3.
Unlock the back focus locking button.
Press and hold the center key for more than 1 second until
the Install menu appears.
4.
Select Len Wizard and move cursor to the Set Back Focus
Now item.
5.
Turn the back focus adjustment as required.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Connection and mounting | en
19
Bosch
6.
Lock the back focus locking button.
Bosch
7.
Press and hold the center key for more than 1 second until
all the menus disappear.
8.
4.6
Close the side door panel.
Mounting the camera
The camera can be mounted either from the top or from the
bottom (1/4" 20 UNC thread). The bottom mounting is isolated
from ground to prevent ground loops.
Figure 4.7
Bosch Security Systems
Mounting a camera
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
20
en | Connection and mounting
!
Dinion2X
CAUTION!
Do not point the camera/lens into direct sunlight as this may
damage the sensors.
Note:
A wide range of accessories is available for indoor and outdoor
mounting.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
5
Configuration | en
21
Configuration
The camera normally provides an optimal picture without the
need for further adjustments. Advanced set-up options are
available in a menu system for getting the best results under
special circumstances.
The camera implements your changes immediately so that
before and after settings are easily compared.
5.1
5.1.1
Menus
Top level menus
There are two upper level menus: a Main menu and an Install
menu. The menus have functions that can be selected directly
or submenus for more detailed set-up.
–
To access the Main menu, press the menu/select button
(center) for less than 1 second. The Main menu appears on
the monitor. The Main menu allows you to select and setup the picture enhancement functions. If you are not happy
with your changes, you can always recall the default values
for the mode.
–
The camera also has an Install menu in which the
installation settings can be set. To access the Install menu,
press the menu/select button (center) for longer than 2
seconds.
5.1.2
Menu navigation
Five keys, located behind the side door panel, are used for
navigating through menu system.
Bos
ch
Bosch
Figure 5.1 Side panel door
Bosch Security Systems
Installation Manual
Figure 5.2 Menu/select key
AR18-08-B013 | v1.0 | 2009.03
22
en | Configuration
Dinion2X
Up key
Menu/Select key (center)
Right key
Down key
Left key
Figure 5.3
Navigation
–
Use the up or down keys to scroll through a menu.
–
Use the left or right keys to move through options or to set
parameters.
–
When in a menu, quickly double-press the menu/select key
to restore the selected item to its factory default.
–
To close all menus at once hold down the menu/select key
until the menu display disappears or continually select the
Exit item.
Some menus automatically close after about two minutes; other
menus have to be closed manually.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
5.2
Configuration | en
23
Pre-defined modes
There are six pre-defined modes with settings to make
configuration easier. You can select one of the six pre-defined
modes in the Install/Mode submenu. The modes are defined as
follows;
1.
24-hour
Default installation mode to provide stable pictures over a
24-hour period. These settings are optimized for out-ofthe-box installation.
2.
Traffic
Capture high-speed objects using default shutter in
variable lighting conditions.
3.
Low light
Provide extra enhancement, such as AGC and SensUp to
make usable pictures in low-light conditions.
4.
Smart BLC
Settings optimized to capture details in high contrast and
extremely bright-dark conditions.
5.
Low noise
Enhancements are set to reduce picture noise. Useful for
conditional refresh DVR and IP storage systems because
reducing noise reduces the amount of storage required.
6.
Analog systems
Use this mode if the camera is connected to a purely
analog system (e.g. matrix switcher with VCR) or to a CRT
monitor. Useful mode for evaluating/demonstrating the
camera when it is directly connected to a CRT monitor.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
24
en | Configuration
5.3
Dinion2X
Day/Night switching
The camera is equipped with a motorized IR filter. The
mechanical IR filter can be removed in low-light or IR
illuminated applications by software configuration settings.
If Auto switching mode is selected, the camera automatically
switches the filter depending on the observed light level. The
switching level is programmable. In Auto switching mode the
camera prioritizes motion (the camera gives sharp images
without motion blur as long as the light level permits) or color
(the camera gives color pictures as long as the light level
permits). The camera recognizes IR illuminated scenes to
prevent unwanted switching to color mode.
There are four different methods of controlling the IR filter:
5.4
–
via an alarm input,
–
via Bilinx communication,
–
automatically, based on the observed light levels, or
–
as part of the programmable mode profile.
Camera control communication (Bilinx)
This camera is equipped with a coaxial communications
transceiver (also referred to as Bilinx). In combination with VPCFGSFT, the camera setting can be changed from any point
along the coaxial cable. All menus can be accessed remotely
giving full control of the camera. With this method of
communication it is also possible to disable the local keys on
the camera.
To avoid loss of communication on an installed camera, the
Communication On/Off selection is not available while using
remote control. This function can only be accessed with the
camera buttons. Bilinx communications can only be disabled
using the buttons on the camera.
Disabled camera buttons
When the Bilinx communications link is active, the buttons on
the camera are disabled.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
5.5
Configuration | en
25
Main menu structure
Item
Selection
Description
Mode
Submenu
Sets up operating modes 1 to 6
ALC
Submenu
Video level control
Shutter/AGC
Submenu
Shutter and automatic gain control
Day/Night
Submenu
Day/Night for color/mono operation
Enhance /
Submenu
Picture enhancement and performance
Color
Submenu
White balance and color rendition
VMD
Submenu
Video motion detection
Dynamic
Engine
5.5.1
Mode submenu
Item
Selection
Description
Mode
1 to 6
Selects operating mode.
Mode ID
Alphanumeric
Mode name (11 characters maximum)
Copy active
Available
Copies current mode settings to the mode
mode
mode
number selected.
numbers
Default mode
Submenu
Restores camera to the factory default
settings.
EXIT
Bosch Security Systems
Returns to main menu.
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
26
en | Configuration
Dinion2X
5.5.2
ALC submenu
Item
Selection
Description
ALC level
-15 to +15
Selects the range within which the ALC will
operate. A positive value is more useful for
low-light conditions; a negative value is more
useful for very bright conditions.
Some ALC adjustment may improve scene
content when Smart/BLC is enabled.
Peak/average
-15 to +15
Adjusts the balance between peak and
average video control. A negative value gives
more priority to average light levels; a positive
value gives more priority to peak light levels.
Video iris lens: choose an average level for
best results (peak settings may cause
oscillations).
ALC speed
Slow, medium,
Adjusts the speed of the video level control
fast
loop. For most scenes it should remain at the
default value.
DVR/IP
On, Off
Encoder
On - The camera output is optimized for
connection to a DVR or IP encoder to
compensate for compression methods.
Off - The camera output is optimized for
connection to an analog system (matrix
switcher or monitor.
EXIT
AR18-08-B013 | v1.0 | 2009.03
Returns to main menu.
Installation Manual
Bosch Security Systems
Dinion2X
5.5.3
Configuration | en
27
Shutter/AGC submenu
Item
Selection
Description
Shutter
AES, FL, Fixed
AES (auto-shutter) - the camera automatically
sets the optimum shutter speed.
FL - flickerless mode avoids interference from
light sources (recommended for video-iris or
DC-iris lenses only).
FIXED - allows a user defined shutter speed.
Default (AES)
1/50 (PAL),
In AES mode, the camera tries to maintain the
shutter
1/60 (NTSC)
selected shutter speed as long as the light
or
1/100, 1/120,
level of the scene is high enough.
Fixed shutter
1/250,
In Fixed mode, selects shutter speed.
1/500,
1/1000,
1/2000,
1/5000,
1/10K
Actual shutter
Displays the actual shutter value from the
camera to help compare lighting levels and
optimum shutter speed during set-up.
Gain control
On, Fixed
On - the camera automatically sets the gain to
the lowest possible value needed to maintain
a good picture.
Fixed - sets Fixed AGC value.
Maximum AGC
0 to 30 dB
Selects the maximum value the gain can have
or
during AGC operation.
Fixed AGC
Selects the gain setting for Fixed gain
operation (0 is no gain).
Actual AGC
Displays the actual AGC value from the
camera to help compare gain level with
lighting levels and picture performance.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
28
en | Configuration
Dinion2X
Item
Selection
Description
SensUp
Off, 2x, 3x, …,
Selects the factor by which the sensitivity of
Dynamic
10x
the camera is increased.
When active, some noise or spots may appear
in the picture. This is normal camera
behavior. It may also cause motion blur on
moving objects.
EXIT
5.5.4
Returns to main menu.
Day/Night submenu
Item
Selection
Description
Day/Night
Auto, Color,
Auto - the camera switches the IR cut-off filter
Monochrome
on and off depending on the scene
illumination level.
Monochrome - the IR cut-off filter is removed,
giving full IR sensitivity.
Color - the camera always produces a color
signal regardless of light levels.
Switch level
-15 to +15
Sets the video level in Auto mode at which
the camera switches to monochrome
operation.
A low (negative) value means that the camera
switches to monochrome at a lower light
level. A high (positive) value means that the
camera switches to monochrome at a higher
light level.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Configuration | en
Item
Selection
Description
Priority
Motion, Color
In AUTO mode:
29
Color - the camera gives a color image as long
as the light level permits.
Motion - the camera avoids motion blur as
long as the light level permits (it switches to
monochrome earlier than it would with Color
priority).
IR contrast
Enhanced,
Enhanced - the camera optimizes contrast in
Normal
applications with high IR illumination levels.
Select this mode for IR (730 to 940 nm) light
sources and for scenes with grass and green
foliage.
Normal - the camera optimizes contrast in
mono applications with visible light
illumination.
Color burst
(mono)
On, Off
Off - the color burst in the video signal is
switched Off in monochrome mode.
On - the color burst remains active even in
monochrome mode (required by some DVRs
and IP encoders).
EXIT
Bosch Security Systems
Returns to main menu.
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
30
en | Configuration
5.5.5
Dinion2X
Enhance / Dynamic Engine submenu
Item
Selection
Description
Dynamic
Off, XF-DYN,
Off: - turns off all automatic scene detail and
Engine
2X-DYN*,
enhancements (only recommendedfor
SmartBLC
testing).
XF-DYN: - extra internal processing is enabled
for low-light applications (traffic, etc.).
* 2X-DYN is
2X-DYN: - 2X-Dynamic adds dual sensor
only
exposure to the XF-DYN features. In harsh
available in
lighting conditions pixels from each exposure
LTC0498
are mixed to give a more detailed image (use
models.
2X-DYN when SmartBLC is not required).
SmartBLC: - BLC window and weighting
factor are automatically defined. Camera
dynamically adjusts these for changing light
conditions. Includes all the benefits of 2XDYN.
Autoblack
On, Off
Autoblack On automatically increases the
visibility of details even when scene contrast
is less than full-range due to mist, fog, etc.
Black level
-50 to +50
Adjusts the black offset level.
A low (negative) value makes the level darker.
A high (positive) value makes the level lighter
and may bring out more detail in the darker
areas.
Sharpness
-15 to +15
Adjusts the sharpness of the picture. 0
corresponds to the default position.
A low (negative) value makes the picture less
sharp. Increasing sharpness brings out more
detail.
Extra sharpness can enhance the details of
license plates, facial features and the edges
of certain surfaces.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Configuration | en
Item
Selection
Description
Dynamic noise
Auto, Off
In AUTO mode the camera automatically
reduction
31
reduces the noise in the picture.
This may cause some motion blur on
exceptionally fast moving objects immediately
in front of the camera. This can be corrected
by widening the field of view or selecting Off.
Peak White
On, Off
Use Peak White Invert to reduce glare from
Invert
the CRT/LCD display.
Use in ANPR/LPR applications to reduce
headlight glare. (Test on-site to ensure that it
does benefit the application and is not
distracting for operators of the security
system.)
EXIT
5.5.6
Returns to main menu.
Color submenu
Item
Selection
Description
White balance
ATW,
ATW - Auto tracking white balance allows the
AWBhold,
camera to constantly adjust for optimal color
Manual
reproduction.
AWBhold - Puts the ATW on hold and saves
the color settings.
Manual - the Red, Green, and Blue gain can be
manually set to a desired position.
Speed
Red gain
Fast, Medium,
Adjusts the speed of the white balance
Slow
control loop.
-5 to +5
ATW and AWBhold - adjusts the Red gain to
-50 to +50
Manual - adjusts the Red gain.
optimize the white point.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
32
en | Configuration
Dinion2X
Item
Selection
Description
Blue gain
-5 to +5
ATW and AWBhold - adjusts the B gain to
optimize the white point.
-50 to +50
Manual - adjusts the Blue gain.
Green gain
-50 to +50
Manual - adjusts the Green gain.
Saturation
-15 to +5
Adjusts the color saturation. -15 gives a
monochrome image.
EXIT
5.5.7
Returns to main menu.
VMD submenu
Item
Selection
Description
VMD
Off, Silent,
Off - Video Motion Detection (VMD) is off.
OSD
Silent - video motion generates silent alarm.
OSD - video motion generates on-screen text
message alarm.
VMD area
Submenu
Select to enter the area set-up menu to define
the detection area.
Motion
Indicates the peak of measured motion in the
indicator
selected area. Press either the right, left or
center navigation button to reset.
VMD
Sets the sensitivity for motion to the desired
sensitivity
level. The longer the white bar, the more
motion is required to acitvate the VMD alarm.
Motion above this level activates alarm.
OSD alarm
Alphanumeric
Text for on-screen display alarm (16
text
characters maximum).
EXIT
Returns to main menu.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Configuration | en
33
Selecting an area for VMD masking
To set-up an area for VMD masking, access the area menu by
selecting the VMD Area option from the VMD menu. Upon
entering the Area menu, the current area is displayed with the
upper left corner flashing. The flashing corner of the image can
be moved with the Up, Down, Left, Right arrow keys. Pressing
the Select key moves the flashing cursor to the opposite corner,
which can now be moved. Pressing Select again freezes the
area and exits the area menu.
There is one programmable VMD area.
Note:
When VMD is enabled, normal light fluctuations or
environmental factors can contribute to false-positive alarms.
Because of this, it is recommended that you do not connect the
VMD-triggered alarm output of the camera to a monitored alarm
system as the false-positive alarms may be considered a
nuisance.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
34
en | Configuration
5.6
Dinion2X
Install menu structure
Item
Selection
Description
Language
Submenu
Select on-screen display (OSD) language
Lens Wizard
Submenu
Select to optimize the camera-lens
combination backfocus point.
Synchroniza-
Submenu
Sets synchronization parameters
tion
Alarm I/O
Submenu
Program the alarm input and output
functionality.
Connections
Submenu
Connection parameters
Test signals
Submenu
Test patterns and texts
Camera ID
Submenu
Select to access ID submenu
Privacy
Submenu
Sets up a masking area
Submenu
Returns all settings for all modes to factory
masking
Default ALL
defaults
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
5.6.1
Configuration | en
35
Language submenu
Item
Selection
Description
Language
English
Displays the menus on the OSD in the
Spanish
chosen language.
French
German
Portuguese
Polish
Italian
Dutch
Russian
EXIT
5.6.2
Returns to Install menu.
Lens Wizard submenu
Item
Selection
Description
Lens type
Auto, Manual,
Auto: - automatically selects the type of lens.
DC-iris, Video
Manual, DC-iris, Video modes: select the
matching lens type to force the camera to the
correct lens mode.
Detected
Shows the type of lens detected when auto
lens detection is used.
Set Backfocus
Select to fully open the iris. Follow the
now
instructions below for setting the backfocus
for your particular lens type.
After focusing the object of interest remains
in focus under bright and low light conditions.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
36
en | Configuration
Item
Dinion2X
Selection
Description
Set LVL
Only for video-iris lenses.
Adjust the level control on the lens to center
the level detector indicator (see below).
EXIT
Returns to Install menu.
Adjustment procedure DC-iris Lens
1.
Unlock the back focus locking button.
2.
Access the Lens Wizard menu.
3.
Set Back Focus Now is highlighted in the menu.
4.
Turn the back focus adjustment as required.
5.
Lock the back focus locking button.
6.
Exit the menu.
Adjustment procedure Manual-iris Lens
1.
Unlock the back focus locking button.
2.
Adjust the lens to the maximum lens opening.
3.
Turn the back focus adjustment as required.
4.
Lock the back focus locking button.
5.
Adjust lens opening to suit scene.
Adjustment procedure Video-iris Lens
1.
Unlock the back focus locking button.
2.
Access the Lens Wizard menu.
3.
Set Back Focus Now is highlighted in the menu.
4.
Turn the back focus adjustment as required.
5.
Lock the back focus locking button.
6.
Select Set LVL in the menu; the Level bar appears.
7.
Point the camera at the scene it will be mostly viewing.
8.
Adjust the level potentiometer located on the lens until the
Level bar is in the central position.
9.
Exit the menu.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
5.6.3
Configuration | en
37
Synchronization submenu
Item
Selection
Description
Synchroniza-
Internal
Internal - for free running camera operation.
tion
Line lock
Line lock - to lock to the AC power supply
HV lock,
HV lock - locks the camera to the sync signal
Genlock,
supplied to the SYNC connector.
Genlock - locks the camera’s subcarrier to the
signal supplied to the SYNC connector.
Horizontal
-25 . . 0 . . +25
Adjusts the horizontal phase offset.
phase
Subphase
0, 2 . . . 358
EXIT
5.6.4
Adjusts the subcarrier phase.
Returns to Install menu.
Alarm I/O submenu
Item
Selection
Description
Alarm input
None, high,
Select none to disable the alarm input. Select
low
active-high or active-low for the alarm input
connector.
Alarm action
None,
Selects the operating mode of the camera
Mode 1 to 6,
when the alarm input is active.
Mono
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
38
en | Configuration
Dinion2X
Item
Selection
Description
Alarm output
VMD,
VMD: - output relay closes on VMD alarms.
External
External device: - make the output relay
device,
available to remote communication devices.
Night mode
Night mode active: - output relay closes when
active,
camera is in monochrome mode.
Filter toggle
Filter toggle: - output relay closes just before
the IR filter starts moving and opens when
video level has stabilized (2 to 3 seconds)
EXIT
5.6.5
Returns to Install menu.
Connections submenu
Item
Selection
Description
Sync. input
High Z,
Select 75 ohm if the external sync input is not
75 ohm
terminated elsewhere.
Notch filter
On, Off
Switches notch filter on or off. The notch
filter can remove a Moiré pattern or color
artifacts caused by closely spaced vertical
lines or objects (e.g. vertical security bars
over windows).
Bilinx Comms.
On, Off
If Off, Bilinx communications is disabled.
Camera
Enable,
Enable or disable the camera buttons from
buttons
disable
working.
Cable
Off, Default,
Cable compensation is used to avoid the
compensation
RG59, RG6,
need for amplifiers in long distance coaxial
Coax12
connections up to 1000 m (3000 ft). For
optimum results select the coaxial cable type
used or, if unknown, select default.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Configuration | en
Item
Selection
Description
Compensation
0,1,2 . . .+15
Sets the level of cable compensation
39
level
EXIT
5.6.6
Returns to Install menu.
Test signal submenu
Item
Selection
Description
Show camera
Off, On
Select On to overlay the camera ID on the
ID
Test pattern
video test signal.
Color bars
Select the desired test pattern to help
100%,
installation and fault-finding.
Grayscale 11step,
Sawtooth 2H,
Checker
board,
Cross hatch,
UV plane
EXIT
Bosch Security Systems
Returns to Install menu.
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
40
en | Configuration
5.6.7
Dinion2X
Camera ID submenu
Item
Selection
Camera ID
Description
Enter a 17-character camera name. Use
Left/Right to change position in the string;
use up/down to select character. Use Select
to exit.
Display ID pos.
Off, Top left,
Select the screen position of the camera ID.
Top right,
Bottom left,
Bottom right
Camera ID
On, Off
Displays a grey border behind the camera ID
border
to make it easier to read.
MAC address
Shows MAC address (factory set, cannot be
changed).
Ticker bars
On, Off
The ticker bar moves continuously to show
that the image is live and not frozen or played
back.
Display mode
Off, Top left,
Camera mode is displayed on the screen in
ID
Top right,
the selected position.
Bottom left,
Bottom right
EXIT
5.6.8
Returns to Install menu.
Privacy masking submenu
Item
Selection
Description
Pattern
Black, Grey,
Selects pattern for all masks.
White, Noise
Mask
1, 2, 3, 4
AR18-08-B013 | v1.0 | 2009.03
Four different areas can be masked.
Installation Manual
Bosch Security Systems
Dinion2X
Configuration | en
Item
Selection
Description
Active
On, Off
Turns each of the four masks on or off.
Window
Submenu
Select to open a window in which to define
41
the mask area.
Selecting an area for privacy masking
To set-up an area for privacy masking, access the area menu by
selecting the Area option from the privacy masking menu. Upon
entering the Area menu, the current area is displayed with the
upper left corner flashing. The flashing corner of the image can
be moved with the Up, Down, Left, Right arrow keys. Pressing
the Select key moves the flashing cursor to the opposite corner,
which can now be moved. Pressing Select again freezes the
area and exits the area menu.
There are four programmable privacy mask areas.
5.6.9
Defaults submenu
Item
Selection
Description
Restore All
No, Yes
Restores all settings of the six modes to their
default (factory) values. Select YES then
press the Menu/Select button to restore all
values.
When completed the message RESTORED! is
shown.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
42
en | Configuration
AR18-08-B013 | v1.0 | 2009.03
Dinion2X
Installation Manual
Bosch Security Systems
Dinion2X
Troubleshooting | en
6
Troubleshooting
6.1
Resolving problems
43
The following table is intended to help you identify the causes
of malfunctions and correct them when possible.
Malfunction
Possible causes
Solution
No image
Defective camera.
Connect a local monitor
transmission to
to the camera and check
remote location.
the camera function.
Faulty cable connections. Check all cables, plugs,
contacts and
connections.
Incorrect cable
Ensure that Video and
connections.
Sync connections are not
reversed.
When using DC power
ensure that polarity is
correct.
No connection
The unit's configuration.
Check all configuration
established, no
parameters.
image transmission. Faulty installation.
Check all cables, plugs,
contacts and
connections.
6.2
Customer service
If you cannot resolve a fault, please contact your supplier or
system integrator, or contact Bosch Security Systems
Customer Service directly.
The Installer should write down all information regarding the
unit so that it can be referenced for warranty or repair. The
version numbers of the firmware and other status information
can be seen when the unit starts or by opening the Install
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
44
en | Troubleshooting
Dinion2X
menu. Note down this information and the information found
on the camera label before contacting customer service.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Maintenance | en
7
Maintenance
7.1
Repairs
45
CAUTION!
Never open the casing of the camera. The unit does not contain
!
any user serviceable parts. Ensure that all maintenance or
repair work is performed only by qualified personnel (electrical
engineering or network technology specialists). If in doubt,
contact your dealer's technical service center.
7.1.1
Transfer and disposal
The camera should only be passed-on together with this
installation guide. The unit contains environmentally hazardous
materials that must be disposed of according to law. Defective
or superfluous devices and parts should be disposed of
professionally or taken to your local collection point for
hazardous materials.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
46
en | Maintenance
AR18-08-B013 | v1.0 | 2009.03
Dinion2X
Installation Manual
Bosch Security Systems
Dinion2X
Technical Data | en
8
Technical Data
8.1
Specifications
47
1/2-inch CCD version
Type number
LTC0630/11
LTC0630/21
LTC0630/51
LTC0630/61
Standard
PAL
NTSC
PAL
NTSC
Active pixels
752 x 582
768 x 494
752 x 582
768 x 494
Rated supply
+12 VDC ±10%
+12 VDC ±10%
230 VAC 50 Hz
120 VAC 60 Hz
voltage
24 VAC (50 Hz)
24 VAC (60 Hz)
±10%
±10%
Minimum
<0.18 lux
illumination
<0.024 lux (in monochrome mode)
1/3-inch CCD version
Type number
LTC0498/11
LTC0498/21
LTC0498/51
LTC0498/61
Standard
PAL
NTSC
PAL
NTSC
Active pixels
752 x 582
768 x 494
752 x 582
768 x 494
Rated supply
+12 VDC ±10%
+12 VDC ±10%
230 VAC 50 Hz
120 VAC 60 Hz
voltage
24 VAC (50 Hz)
24 VAC (60 Hz)
±10%
±10%
Minimum
<0.24 lux
illumination
<0.038 lux (in monochrome mode)
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
48
en | Technical Data
Dinion2X
All versions
Imager
Interline CCD
Resolution
540 TVL
SNR
> 50 dB
Video output
1 Vpp, 75 Ohm
Synchroniza-
Internal, Line Lock, HV-lock, or Genlock selectable
tion
Shutter
AES (1/60 [1/50] to 1/10000) customer selectable
AES (1/60 [1/50] to 1/15000) automatic
flickerless, fixed selectable
Day/Night
Color, Mono, Auto
Sens Up
Adjustable from Off to 10x
AGC
AGC On or Off (0 dB) selectable
Dynamic engine XF-Dynamic, 2X-Dynamic*, SmartBLC
* 2X-DYN is only available in LTC0498 models.
DNR
Automatic noise filtering On/Off selectable
Sharpness
Sharpness enhancement level selectable
White Balance
ATW, AWBhold and manual (2500 to 10000K)
Color
Adjustable from monochrome (0%) to 133% color
saturation
Lens mount
CS compatible, c-mount compatible with supplied
adapter ring
ALC lens
Video or DC iris auto detect
Test pattern
Color bars 100%, Greyscale 11-step, Sawtooth 2H,
generator
Checker board, Cross hatch, UV plane
Video Motion
One area, fully programmable
Detection
(VMD)
Privacy
Four independent areas, fully programmable; black,
Masking
white, grey, noise
Communication Two-way Bilinx (bi-directional)
Languages
English, Spanish, French, German, Portuguese, Polish,
(OSD)
Italian, Dutch, Russian
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
Modes
Technical Data | en
49
6 programmable (preset) modes: 24-hour, Traffic, Lowlight, SmartBLC, Low noise, Analogue systems
Peak White
Suppresses highlights in scenes
Invert
Misc.
Notch filter, Actual AGC, Actual shutter, IR contrast
Power
<5 W
consumption
Dimensions
58 x 66 x 122 mm (2.28 x 2.60 x 4.80 in) without lens
(H x W L)
Weight
450 g (0.99 lb) without lens
Tripod mount
Bottom (isolated) and top 1/4" 20 UNC
Operating
-20 °C to +55 °C (-4 °F to +131 °F)
temperature
Controls
Bosch Security Systems
OSD with softkey operation
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
50
en | Technical Data
8.1.1
Dinion2X
Dimensions
118 (4.646)
85 (3.346)
34 (1.339)
1/4"-20 UNC
Dinion2X D/N Camera
1/4"-20 UNC
48 (1.889)
123 (4.843)
59 (2.323)
67 (2.638)
mm (in)
Figure 8.1
AR18-08-B013 | v1.0 | 2009.03
Dimensions
Installation Manual
Bosch Security Systems
Dinion2X
8.1.2
Technical Data | en
51
Accessories
–
Indoor mounting brackets
–
Outdoor environmental housings
–
Lenses (varifocal, fixed and motorized zoom)
–
Bilinx communication interface box and software
Contact a Bosch representative in your area for the latest
available accessories or visit our website at
www.boschsecurity.com
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
52
en | Technical Data
AR18-08-B013 | v1.0 | 2009.03
Dinion2X
Installation Manual
Bosch Security Systems
Dinion2X
| en
53
Glossary
A
AES
Automatic Electronic Shutter (see Electronic iris).
Aperture
The size of the opening in the lens iris that controls the amount
of light reaching the CCD Sensor. The larger the F-number, the
less light reaches the sensor. An increase of one F-stop, halves
the amount of light reaching the sensor.
AutoBlack
A technique of boosting the video signal level to produce a full
amplitude video signal, even when the scene contrast is less
than full range (glare, fog, mist, etc.).
Automatic Gain Control (AGC)
The electronics that regulate the gain or amplification of the
video signal. AGC is used in low-light conditions with the iris
fully open.
AutoIris
The lens iris opening is automatically adjusted to allow the
correct illumination of the camera sensor. With a direct drive
(DC) iris lens, the camera controls the aperture size. A video iris
lens has the control circuit in the lens itself.
Auto Level Control (ALC)
The adjustment of the video level to give the desired brightness
level. This can be done electronically or by means of an iris
control.
Auto White Balance (AWB)
A feature that allows a color camera to automatically adjust its
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
54
en |
Dinion2X
output color to give a natural color, independent of the lighting
used.
B
Backfocus
The distance between the image plane and the rear portion of
the lens. Correct backfocus adjustment ensures that the
camera remains in focus under various conditions.
Bilinx
A communications protocol that allows remote control,
configuration, and updates to be performed over the video
cable (Coax or Passive UTP).
Bilinx address
The address may be set locally using the Bilinx Configuration
Tool for Imaging Devices (CTFID).
Back Light Compensation (BLC)
Selectively amplifies parts of the image to compensate for large
contrast differences when only a portion of the image is brightly
lit (e.g. a person in a sunlit doorway). See also Smart BLC.
C
Charged Coupled Device (CCD)
A CCD is a type of solid state image sensor used in CCTV
cameras. The sensor converts light energy into electrical
signals.
CCD Format
Indicates the size of the camera sensor used. In general, the
larger the sensor, the more sensitive the camera and the better
the image quality. The format is quoted in inches, for example
1/3 or 1/2 inch.
Color Temperature
A measure of the relative color of illumination. Generally used
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
| en
55
to specify the color balance correction of a camera to achieve a
natural color image.
D
Day/Night (infrared sensitive)
A camera that has normal color operation in situations where
there is sufficient illumination (day conditions), but where the
sensitivity can be increased when there is little light available
(night conditions). This is achieved by removing the infrared cut
filter required for good color rendition. The sensitivity can be
further enhanced by integrating a number of fields to improve
the signal-to-noise ratio of the camera (this may introduce
motion blur).
Default Shutter
A feature allowing the shutter speed to be set to a fast speed to
eliminate motion blur and provide a detailed and clear image of
fast-moving objects while there is sufficient light. When light
levels fall and other adjustments have been exhausted, the
shutter speed reverts to the standard setting to maintain
sensitivity.
Depth of Field
The distance from the nearest to the furthermost point that
appears in focus. The smaller the aperture, the greater the
depth of field.
Dynamic Noise Reduction (DNR)
A digital video processing technique that measures the noise
(image artifacts) in the picture and automatically reduces it.
E
Electronic iris
Electronic iris (or AES - Automatic Electronic Shutter) adjusts
the camera shutter speed to compensate for lighting changes.
In some cases this can eliminate the need for an autoiris lens.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
56
en |
Dinion2X
F
F-Number
The standard measure of the lens aperture, which is the iris
diameter, divided by the focal length of the lens. The lower the
maximum aperture (F-Number or F-Stop), the more light that
passes through the lens.
F-Stop
See F-Number
Field of View
The measure of the visible area within the camera’s field of
view. The larger the focal length, the smaller the field of view.
The smaller the focal length, the wider the field of view.
Focal Length
The distance from the optical center of the lens to the image of
an object located at an infinite distance from the lens. Long
focal lengths give a small field of view (e.g. telephoto effect),
while short focal lengths give a wide angle view.
I
Infrared Illumination
Electromagnetic radiation (light) with a longer wavelength than
is visible to the human eye. IR illumination is prominent at dusk
and dawn and in incandescent lamps. IR illuminators come in
the form of lamps with the appropriate filters, LEDs, or lasers.
CCD sensors are less sensitive to IR than visible light, but IR
can significantly increase the total illumination level, leading to
a much better image at low light levels.
IRE (Institute of Radio Engineers)
A measurement of video amplitude that divides the area from
the bottom of sync to peak white level into 140 equal units 140 IRE equals 1V peak-to-peak. The range of active video is
100 IRE.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
| en
57
L
Lens wizard
The lens wizard is used when setting the backfocus. It opens
the iris fully while maintaining the correct video level using AES.
Lux
The international (SI) unit of measurement of the intensity of
light. It is equal to the illumination of a surface one meter away
from a single candle.
O
OSD
On-screen Display: Menus are shown on the display monitor.
P
Privacy Masking
The ability to mask out a specific area to prevent it from being
viewed in order to comply with privacy laws and particular site
requirements.
PWIE
Peak White Inverse Engine: White highlights are automatically
turned black to reduce bright spots. Useful in traffic and car
park applications.
R
Region of Interest
A specific area within a field of view, used by the motion
detection algorithm to identify motion.
Resolution
The measure of the fine detail that can be seen in an image. For
analog systems this is typically measured in horizontal
Television Lines or TVL. The higher the TVL rating, the higher
the resolution.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
58
en |
Dinion2X
S
Saturation
The amplitude of the chrominance signal affecting the vividness
of the color.
Sensitivity
A measure of the amount of light required to provide a standard
video signal. Sensitivity values are stated in lux (see Lux).
SensUp (sensitivity up)
Increases camera sensitivity by increasing the integration time
on the CCD (lowering shutter time from 1/50 to 1/5 s). This is
accomplished by integrating the signal from a number of
consecutive video fields to reduce signal noise.
Signal-to-noise ratio
The ratio between a useful video signal and unwanted noise
measured in dB.
Smart BLC (Back Light Compensation)
Smart back-light compensation allows the camera to
automatically compensate for bright areas of a high contrast
scene without having to define a window or area.
U
UTP (Unshielded Twisted Pair)
A variant of twisted pair cabling, UTP cable is not surrounded
by any shielding. The wires in a twisted pair cable are twisted
around each other to minimize interference from the other
twisted pairs in the cable. UTP is the primary wire type for
telephone usage and the most commonly used type of
networking cable.
AR18-08-B013 | v1.0 | 2009.03
Installation Manual
Bosch Security Systems
Dinion2X
| en
59
V
VMD
Video Motion Detection: An algorithm for motion detection in
which the camera compares the current image with a reference
image and counts the number of pixels that have changed
between the two images. An alarm is generated when the
number of pixel changes exceeds a user-configured threshold.
W
WDR (Wide Dynamic Range)
A cameras dynamic range is the difference between the
minimum and maximum acceptable signal levels. A scene with
both very low and very high illumination levels requires a
camera with a wide dynamic range to handle it correctly and
produce a useful image.
Bosch Security Systems
Installation Manual
AR18-08-B013 | v1.0 | 2009.03
60
en |
AR18-08-B013 | v1.0 | 2009.03
Dinion2X
Installation Manual
Bosch Security Systems
Bosch Security Systems
www.boschsecurity.com
© Bosch Security Systems, 2009
Download PDF
Similar pages