ASSEMBLY INSTRUCTIONS
LX Sit-Stand Wall Mount System
with Small CPU Holder
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
用户指南 : 汉语
888-45-278-W-03 rev.K • 02/17
1 of 28
Features & Specifications
Maximum Screen
Size* = 42”
*Limited to 25 lbs
maximum
1.38" - 3.75"
(35-95 mm)
50 lbs (22.7 kg)
25 lbs
(11.3 kg)
3.15"
(80mm)
1.57"
(40mm)
1.34"
(34mm)
1.14"
ENGLISH
(29mm)
6.5"
7.1"
(165mm)
0-5 lbs
(0-2.3 kg)
(180mm)
5.1"
(129mm)
180°
70°
360°
20"
(508 mm)
180°
5°
0° or 360°
180°
90°
180°
360°
20"
(508 mm)
5°
888-45-278-W-03 rev.K • 02/17
2 of 28
Tools Needed
A
B
C
D
2
1
1
Stud Finder
Concrete Wall Mounting
Ø 3/8” (10mm)
2
13 mm
Wood Stud Mounting
Ø 3/16" (5mm)
Components
B
C
1x
2x
4x
2x
4x
2x
D
1x
1x
2x
1
M4.2 x 25mm
ENGLISH
1x
A
2x
9x
1/4-20 x 1/2"
14x
1x
2
7x
14x
1/4-20 x 2"
1x
1x
12x
7x
2x
M4 x 14mm
2x
M10 x 16mm
3
2x
1x
6mm
888-45-278-W-03 rev.K • 02/17
3 of 28
Components
A
B
2x
1
C
D
1x
1x
2x
1x
1x
2x
2
1x
4x
1x
ENGLISH
4x
M4 x 10mm
3
4x
1x
4x
4x
4x
M4 x 10mm
8x
M3 x 6mm
4x
2x
M6
M6 x 45mm
1x
4x
1x
4x
M5 x 7mm
4
10-24 x 1/2"
4x
M4 x 8mm
4mm
5x
4x
1x
5
1/8”
5mm
M8 M5 Kit
4x
6
4x
M8-M5
Reducer
M5x20mm
4x
M4x12mm
4x
4x
M5x12mm
M6x12mm
888-45-278-W-03 rev.K • 02/17
4 of 28
1
Mounting Height for Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’4”-5’9”
(163-175cm).
If user heights are different than this, you should change mounting height to accommodate user heights. (Change mounting height one inch for every one inch difference in user heights).
6”
(152 mm)
Mounting height assumes there is a 6” (152 mm) distance between the center of your monitor mounting holes and the top of the screen. If your distance is smaller, you should increase mounting height
accordingly, if your distance is larger, you should decrease your mounting height accordingly.
5’4” - 5’9”
(163-175cm)
5’4” - 5’9”
(163-175cm)
21”
(533 mm)
21”
(533 mm)
ENGLISH
41”
(1041mm)
37.5”
(953mm)
28”
< 27”
(711mm)
(686mm)
23”
< 22”
(584mm)
(559mm)
Determine mounting location:
Front view with arm pushed back against the wall.
Top view showing range of motion when pulled out from the wall.
20”
(516mm)
0.2”
(5mm)
22”
(562mm)
1.3”
(32mm)
10.2”
(259mm)
4.2”
(106mm)
27.6”
(701mm)
888-45-278-W-03 rev.K • 02/17
5 of 28
2
WARNING: Ensure that the wall structure is capable
of supporting four times the total weight of mounted
equipment. Mounting to wall surfaces that do not meet
this criteria may result in an unstable, unsafe condition
which could lead to personal injury and/or property
damage. Consult a construction professional if you
have any doubt about what this means in regard to
your particular application.
ENGLISH
CAUTION: Make sure the wall mount bracket is level,
flush and snug to the wall surface. DO NOT OVERTIGHTEN THE BOLTS.
Wood
Madera
Bois
Solide Holzbalkenträger
Massief Houten Pilaren
Due montanti in legno massiccio
木
木质
나무
Studs ≥ 25 gauge steel
Pernos de acero de calibre ≥ 25
Goujons ≥ calibre 25 en acier
Bolzen ≥ Blechlehre Nr. 25
Verbindingsbouten ≥ 25 gauge staal
Prigionieri in acciaio spessore ≥ gauge 25 (0,556 mm)
Reglar ≥ 25-gauge stål
25ゲージのスチールよりも強力なスタッド
板墙筋为不小于 25 标号的钢材
7
Hollow Wall
Pared
Mur
Wand
Muur
Parete
壁
墙壁
≥ 5/8”
Sheetrock
Sheetrock
Plaque de plâtre
Rigipsplatte
Sheetrock
Cartongesso
Gipsskiva
シートロック
石膏板
8
Requires minimum material thickness of 5/8” (16 mm).
Requiere un grosor mínimo de 16 mm.
Epaisseur minimum de 16 mm.
Requer uma espessura mínima de 5/8” (16 mm).
Mit einer Materialdicke von mindestens 16 mm.
Vereist een minimale materiaaldikte van 1.6 cm.
Richiede uno spessore del materiale non inferiore a 16 mm.
厚さが最低 5/8” (16 mm) の資材が必要。
需要最低材料厚度为 5/8”(16 mm).
888-45-278-W-03 rev.K • 02/17
6 of 28
2
Wood
Madera
Bois
Solide Holzbalkenträger
Massief Houten Pilaren
Due montanti in legno massiccio
木
木质
나무
Studs ≥ 25 gauge steel
Pernos de acero de calibre ≥ 25
Goujons ≥ calibre 25 en acier
Bolzen ≥ Blechlehre Nr. 25
Verbindingsbouten ≥ 25 gauge staal
Prigionieri in acciaio spessore ≥ gauge 25 (0,556 mm)
Reglar ≥ 25-gauge stål
25ゲージのスチールよりも強力なスタッド
板墙筋为不小于 25 标号的钢材
a
b
c
Stud Finder
d
Ø 3/16" (5 mm)
e
f
9
x5
Wood Stud Mounting
7x
Studs ≥ 25 gauge steel
Pernos de acero de calibre ≥ 25
Goujons ≥ calibre 25 en acier
Bolzen ≥ Blechlehre Nr. 25
Verbindingsbouten ≥ 25 gauge staal
Prigionieri in acciaio spessore ≥ gauge 25 (0,556 mm)
Reglar ≥ 25-gauge stål
25ゲージのスチールよりも強力なスタッド
板墙筋为不小于 25 标号的钢材
7x
888-45-278-W-03 rev.K • 02/17
7 of 28
ENGLISH
3
2
Hollow Wall
Pared
Mur
Wand
Muur
Parete
壁
墙壁
a
d
Requires minimum material thickness of 5/8” (16 mm).
Requiere un grosor mínimo de 16 mm.
Epaisseur minimum de 16 mm.
Requer uma espessura mínima de 5/8” (16 mm).
Mit einer Materialdicke von mindestens 16 mm.
Vereist een minimale materiaaldikte van 1.6 cm.
Richiede uno spessore del materiale non inferiore a 16 mm.
≥ 5/8”
Sheetrock
Sheetrock
Plaque de plâtre
Rigipsplatte
Sheetrock
Cartongesso
Gipsskiva
シートロック
石膏板
厚さが最低 5/8” (16 mm) の資材が必要。
需要最低材料厚度为 5/8”(16 mm).
Ø 1/2"
(12.7 mm)
b
14x
c
e
ENGLISH
1
14x
2
1/4-20 x 2"
3
4
f
3
9
888-45-278-W-03 rev.K • 02/17
8 of 28
3a
c
1x
d
2x
M10 x 16mm
1/8"
6mm
e
12x
f
g
ENGLISH
2x
4
10
888-45-278-W-03 rev.K • 02/17
9 of 28
4a
b
8x
1/4-20 x 1/2"
c
Optional locking feature
(customer supplied lock)
d
8x
ENGLISH
10-24 x 1/2"
NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution
over time. Inspect mounting solution for loose fasteners on a routine basis. If desired, apply a
light duty thread locking adhesive to fasteners before installation to prevent back-out.
NOTE: The mounting bracket can be relocated vertically on the
wall track by loosening the the four wall plate screws.
888-45-278-W-03 rev.K • 02/17
10 of 28
5 Mount extension and LCD arm to wall bracket.
c
b
ENGLISH
Do Not
Overtighten
Cap Screw!
M6mm
M6 x 45mm
M6mm
4mm
M6 x 45mm
a
NOTE: when
sliding sleeve
on to bracket,
align slot over
rotation stop.
Do Not
Overtighten
Cap Screw!
4mm
Top View
+
Rotation Stop
on Bracket
Slot
in Sleeve
=
Sleeve on
Bracket
888-45-278-W-03 rev.K • 02/17
11 of 28
5
Portrait / Landscape Options
OPTION i
If you want full portrait/landscape rotation, skip to step 8 on the next page.
OPTION ii
If you do not want your TV/Monitor to rotate all all, you can stop rotation by inseting
the set screw.
ENGLISH
i
ii
0˚
M3 x 6mm
7
13
888-45-278-W-03 rev.K • 02/17
12 of 28
7
Check size of
TV/Monitor hole
pattern
TV/Monitor Hole
Pattern Sizes
VESA Adapter
Configurations
100mm (3-15/16”)
75mm (2-15/16”)
75mm (2-15/16”)
75x75mm
100x100mm
100mm (3-15/16”)
A
100mm (3-15/16”)
14
200mm (7-7/8”)
B
100x200mm
ENGLISH
15
200mm (7-7/8”)
200x200mm
200mm (7-7/8”)
C
15
200mm (7-7/8”)
200x100mm
100mm (3-15/16”)
D
15
888-45-278-W-03 rev.K • 02/17
13 of 28
7 Mount Type A TV/Monitor to Arm
A
75x75mm
100x100mm
4x
M4 x 10mm
100mm (3-15/16”)
75mm (2-15/16”)
M4 x 10mm
ENGLISH
100mm (3-15/16”)
75mm (2-15/16”)
OR
M4 x 10mm
8
14 of 28
17
888-45-278-W-03 rev.K • 02/17
7
Mount VESA Adapters to Arm based on TV/Monitor hole
pattern size (B, C, or D) .
B
C
D
ENGLISH
4x
M5 x 7mm
888-45-278-W-03 rev.K • 02/17
15 of 28
7 Mount Type B, C, or D TV/Monitor to Arm
C
B
D
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
ENGLISH
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
NOTE: To reduce M8
holes for use with M5
screws, or if you have a
model with Samsung
holder rings, follow the
M8M5 KIT instructions
on the next page.
17
OR
OR
M4x12mm
M5x12mm
M6x12mm
8
17
888-45-278-W-03 rev.K • 02/17
16 of 28
M8M5 KIT Instructions
NOTE: follow this step only if your TV/monitor has M8 holes which need to be reduced
to M5 or for Samsung models using the holder ring.
Install M8M5 reducer bushing to TV/Monitor and use M5 x 20 mm
monitor screws to secure when using the Samsung holder ring.
TV/Monitor Mounting
M8 size hole
M5 x 20mm
Monitor Screw
M8M5 Reducer Bushing
Holder Ring
(Not included *Samsung Only)
bracket
covers
To remove covers:
a) Wedge the blade of a flat screwdriver into the gap between the wall mount bracket and the cover.
Rotate the blade upward to pry the cover away.
b) Repeat on the opposite side of the wall mount bracket.
c) Once the cover is free on both sides, lift it off.
Top Cover
Bottom Cover
a
a
b
b
c
c
888-45-278-W-03 rev.K • 02/17
17 of 28
ENGLISH
top
8 Attach
and bottom
9 Mount extension and LCD arm to wall bracket.
4x
c
M4 x 8mm
ENGLISH
b
Do Not
Overtighten
Cap Screw!
M6
M6 x 45mm
M6
4mm
M6 x 45mm
a
NOTE: when
sliding sleeve
on to bracket,
align slot over
rotation stop.
Do Not
Overtighten
Cap Screw!
4mm
Top View
+
Rotation Stop
on Bracket
=
Slot
in Sleeve
Sleeve on
Bracket
888-45-278-W-03 rev.K • 02/17
18 of 28
10
b
a
c
4x
ENGLISH
d
888-45-278-W-03 rev.K • 02/17
19 of 28
11
Attach top and To remove covers:
Wedge the blade of a flat screwdriver into the gap between the wall mount bracket and the cover.
bottom bracket a)Rotate
the blade upward to pry the cover away.
covers
b) Repeat on the opposite side of the wall mount bracket.
c) Once the cover is free on both sides, lift it off.
ENGLISH
Top Cover
Bottom Cover
a
a
b
b
c
c
12 CABLE ROUTING
a
888-45-278-W-03 rev.K • 02/17
20 of 28
12
CABLE ROUTING
b
Leave Slack in cable
ENGLISH
c
888-45-278-W-03 rev.K • 02/17
21 of 28
ROUTING
13 CABLE
a
b
Ø 7/32" (5.6 mm)
1
b
c
d
2
e
f
3
g
M4.2 x 25mm
ENGLISH
M4.2 x 25mm
14
a
b
d
e
c
888-45-278-W-03 rev.K • 02/17
22 of 28
15
CABLE ROUTING
1x
Leave Slack in cable
a
1x
ENGLISH
b
c
888-45-278-W-03 rev.K • 02/17
23 of 28
16
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or difficult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
a
Lift – Up and down
ENGLISH
5mm
5mm
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
WARNING
WARNING
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
888-45-278-W-03 rev.K • 02/17
24 of 28
b
Lift – Up and down
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
WARNING
WARNING
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
888-45-278-W-03 rev.K • 02/17
25 of 28
ENGLISH
5mm
c
Tilt – Forward and Backward
ENGLISH
4mm
CAUTION: DO NOT remove screw. Removing
screw may cause damage to equipment.
Increase Lift Strength
4mm
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
888-45-278-W-03 rev.K • 02/17
26 of 28
How to remove this tilting feature:
3°
3°
Save these screws incase you want to add
this feature later.
ENGLISH
2x
M4 x 14mm
888-45-278-W-03 rev.K • 02/17
27 of 28
Set Your Workstation to Work For YOU!
Learn more about ergonomic computer use at:
www.computingcomfort.org
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists flat.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain flat.
ENGLISH
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
For Warranty visit: www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
© 2015 Ergotron, Inc. All rights reserved.
888-45-278-W-03 rev.K • 02/17
28 of 28
Download PDF
Similar pages