DMP-UB900_P-TQBA2018.book 1 ページ 2016年11月23日 水曜日 午後12時29分
Owner’s Manual
Blu-ray DiscTM Player
Model No.
DMP-UB900
Firmware updates
Panasonic is constantly improving the unit’s firmware to ensure
that our customers are enjoying the latest technology.
Panasonic recommends updating your firmware as soon as you
are notified.
For details, refer to “Firmware updates” (> 18) or
http://panasonic.jp/support/global/cs/ (This site is in English only.)
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this manual for future use.
If you have any questions, visit :
http://shop.panasonic.com/support
Register online at http://shop.panasonic.com/support (U.S. customers only)
TQBA2018-1
P
until
2016/6/21
DMP-UB900_P-TQBA2018.book 2 ページ 2016年11月23日 水曜日 午後12時29分
IMPORTANT SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow the safety instructions on the unit and the applicable safety
instructions listed below. Keep these operating instructions handy for
future reference.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
2
TQBA2018
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Contains FCC ID: H8N-WLU5330
5.47-5.725 GHz band is restricted to indoor operations only.
FCC CAUTION
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operated in conjunction
with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65.
This equipment has very low levels of RF energy that are deemed to
comply without testing of specific absorption ratio (SAR).
But it is desirable that it should be installed and operated keeping
the radiator at least 20 cm (7 7/8q) or more away from person’s body
(excluding extremities: hands, wrists, feet and ankles).
FCC Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached
installation instructions and use only shielded interface cables when
connecting to peripheral devices.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102-5490
Support Contact: http://shop.panasonic.com/support
Conforms to UL STD 60065.
DMP-UB900_P-TQBA2018.book 3 ページ 2016年11月23日 水曜日 午後12時29分
Precautions
WARNING
Unit
To reduce the risk of fire, electric shock or product damage,
≥ Do not expose this unit to rain, moisture, dripping or splashing.
≥ Do not place objects filled with liquids, such as vases, on this
unit.
≥ Use only the recommended accessories.
≥ Do not remove covers.
≥ Do not repair this unit by yourself. Refer servicing to qualified
service personnel.
AC power supply cord
The power plug is the disconnecting device.
Install this unit so that the power plug can be unplugged from the
socket outlet immediately.
Small object
Keep the Memory Card and the batteries out of reach of children to
prevent swallowing.
CAUTION
Unit
≥ This unit utilizes a laser. Use of controls or adjustments or
performance of procedures other than those specified herein
may result in hazardous radiation exposure.
≥ Do not place sources of naked flames, such as lighted candles,
on this unit.
≥ Some portions of this unit may become hot during use. When
moving or cleaning this unit, disconnect the AC power supply
cord and wait for 3 minutes or longer.
Placement
To reduce the risk of fire, electric shock or product damage,
≥ Do not install or place this unit in a bookcase, built-in cabinet or
in another confined space. Ensure this unit is well ventilated.
≥ Do not obstruct this unit’s ventilation openings with newspapers,
tablecloths, curtains, and similar items.
≥ Do not place the unit on amplifiers/receivers or equipment that
may become hot. The heat can damage the unit.
Batteries
Mishandling of batteries can cause electrolyte leakage and may
cause a fire.
≥ Danger of explosion if battery is incorrectly replaced. Replace
only with the type recommended by the manufacturer.
≥ When disposing of the batteries, please contact your local
authorities or dealer and ask for the correct method of disposal.
≥ Do not mix old and new batteries or different types at the same
time.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in a car exposed to direct sunlight
for a long period of time with doors and windows closed.
≥ Do not take apart or short circuit.
≥ Do not recharge alkaline or manganese batteries.
≥ Do not use batteries if the covering has been peeled off.
Restriction on use of
unauthorized copied content
This unit adopts the following technology for copyright protection.
Cinavia Notice
This product uses Cinavia technology to limit the use of
unauthorized copies of some commercially-produced film and
videos and their soundtracks. When a prohibited use of an
unauthorized copy is detected, a message will be displayed and
playback or copying will be interrupted.
More information about Cinavia technology is provided at the
Cinavia Online Consumer Information Center at
http://www.cinavia.com. To request additional information about
Cinavia by mail, send a postcard with your mailing address to:
Cinavia Consumer Information Center, P.O. Box 86851, San
Diego, CA, 92138, USA.
Wireless LAN connection
The following limits are in place regarding the usage of this unit.
You must be aware of these limits before using this unit.
Panasonic will in no way be responsible for any incidental damage
which may arise due to a failure to obey these limits, or to any
condition of use or disuse of this unit.
≥ Data transmitted and received over radio waves may be
intercepted and monitored.
≥ This unit contains delicate electronic components.
Please use this unit in the manner in which it was intended and
follow the following points:
– Do not expose this unit to high temperatures or direct
sunlight.
– Do not bend, or subject this unit to strong impacts.
– Keep this unit away from moisture.
– Do not disassemble or alter this unit in any way.
To dispose or transfer this
unit
The unit may keep the user settings information in the unit. If you
discard this unit either by disposal or transfer, then follow the
procedure to return all the settings to the factory presets to delete
the user settings. (> 35, “To return all settings to the factory
preset.”)
≥ The operation history may be recorded in the memory of this
unit.
Remove batteries if you do not intend to use the remote control for
a long period of time. Store in a cool, dark place.
TQBA2018
3
DMP-UB900_P-TQBA2018.book 4 ページ 2016年11月23日 水曜日 午後12時29分
Table of contents
IMPORTANT SAFETY
INSTRUCTIONS . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . 3
Getting started
Accessories . . . . . . . . . . . . . . . . . 5
Unit and media care . . . . . . . . . . . 5
Playable media. . . . . . . . . . . . . . . 6
Control reference guide . . . . . . . . 8
Connecting to a TV . . . . . . . . . . 10
Connecting to
an amplifier/receiver . . . . . . . . . 11
Connecting to the network . . . . . 16
Settings . . . . . . . . . . . . . . . . . . . 17
Reprogramming
the remote control . . . . . . . . . . 18
Playback
HOME menu . . . . . . . . . . . . . . .
Playback. . . . . . . . . . . . . . . . . . .
Network Service
(Enjoying Netflix, etc.) . . . . . . .
Home Network feature . . . . . . . .
VIERA Link . . . . . . . . . . . . . . . . .
Option menu. . . . . . . . . . . . . . . .
4
TQBA2018
19
19
22
23
25
26
Reference
Setup menu. . . . . . . . . . . . . . . . . 29
Troubleshooting guide . . . . . . . . 35
Specifications . . . . . . . . . . . . . . . 40
Licenses . . . . . . . . . . . . . . . . . . . 43
Limited Warranty. . . . . . . . . . . . . 45
Referencia rápida en español
(Spanish Quick Reference) . . . . . . 46
Index . . . . . . . . . . . . . . . Back cover
DMP-UB900_P-TQBA2018.book 5 ページ 2016年11月23日 水曜日 午後12時29分
Unit and media care
Check the supplied accessories before using this
unit.
1 Remote control
(N2QAYA000131)
2 Batteries for remote control
1 AC power supply cord
(K2CB2YY00098)
∫ Clean this unit with a soft, dry
cloth
≥ Never use alcohol, paint thinner or benzine to
clean this unit.
≥ Before using chemically treated cloth, carefully
read the instructions that came with the cloth.
Getting started
Accessories
Getting started
∫ This unit’s lens
≥ Product numbers are provided in this Owner’s Manual
correct as of June 2016.
These may be subject to change.
≥ Do not use AC power supply cord with other equipment.
∫ Using the remote control
Insert the batteries to the terminal so that it (i
and j) matches those in the remote control.


Use the lens cleaner (not supplied) to clean the
unit’s lens.
∫ Clean discs
DO
Playback
DO NOT
Wipe with a damp cloth and then wipe dry with a
dry cloth.
R03/LR03, AAA
(Alkaline or manganese batteries)
Point it at the remote control signal sensor on this
unit. (> 9)
≥ Handle discs by the edges to avoid inadvertent
scratches or fingerprints on the disc.
≥ Do not attach labels or stickers to discs.
≥ Do not use disc cleaning sprays, benzine,
thinner, static electricity prevention liquids or
any other solvent.
≥ Clean any dust, water, or foreign matter from
the terminals on the rear side of the card.
≥ Do not use the following discs:
– Discs with exposed adhesive from removed
stickers or labels (rented discs, etc.).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart
shapes.
TQBA2018
5
Reference
∫ Disc and card handling
precautions
DMP-UB900_P-TQBA2018.book 6 ページ 2016年11月23日 水曜日 午後12時29分
Playable media
Device
Media markings
BD
Device types
Ultra HD Blu-ray*1*2
Video
BD-Video
Video
BD-RE
Video,
JPEG, MPO
BD-R
Video, MKV,
JPEG, MPO
DVD-Video
DVD-R
DVD
DVD-R DL
DVD-RW
—
—
Video, AVCHD, MKV,
JPEG, MPO,
AAC, ALAC,
DSD (DFF, DSF),
FLAC, MP3, WAV,
WMA
Video, AVCHD
CD-R
CD-RW
Music [CD-DA]
MKV,
JPEG, MPO,
AAC, ALAC, FLAC,
MP3, Music [CD-DA],
WAV, WMA
SD Memory Card (from 8 MB to 2 GB)
SDHC Memory Card (from 4 GB to 32 GB) AVCHD, AVCHD 3D,
SDXC Memory Card (48 GB, 64 GB)
MP4,
(Compatible with both mini and micro
JPEG, MPO
types)
SD
USB
Video
+R/+RW/+R DL
Music CD
CD
Contents format
—
USB devices
(up to 2 TB)
MKV, MP4, MPEG2,
JPEG, MPO,
AAC, ALAC,
DSD (DFF, DSF),
FLAC, MP3, WAV, WMA
≥ See pages 7 and 40 for more information on the types of content that can be played.
*1
*2
See “Enjoying Ultra HD Blu-ray” (> 21)
Unless otherwise indicated, BD-Video content includes Ultra HD Blu-ray content in this Owner’s Manual.
6
TQBA2018
DMP-UB900_P-TQBA2018.book 7 ページ 2016年11月23日 水曜日 午後12時29分
Any other disc that is not specifically
supported or previously described.
≥ DVD-RAM
≥ Super Audio CD
≥ Photo CD
≥ DVD-Audio
≥ Video CD and Super Video CD
≥ HD DVD
∫ Region management information
The unit can play back BD-Video/DVD-Video
discs of the following regions codes, including
“ALL”:
Example:
BD-Video
DVD-Video
1
≥ The unit cannot playback discs in PAL format.
∫ Finalize
Any DVD-R/RW/R DL, +R/+RW/+R DL and
CD-R/RW that are recorded by a recorder need to
be finalized by the recorder to play on this unit.
Please refer to the recorder’s owner’s manuals.
∫ BD-Video
≥ This unit supports high bit rate audio (Dolby®
Digital Plus, Dolby® TrueHD, DTS-HD High
Resolution AudioTM and DTS-HD Master
AudioTM) adopted in BD-Video.
∫ 3D
≥ 3D videos and 3D still pictures can be played
back when this unit is connected to a 3D
compatible TV using a High Speed HDMI
Cable.
∫ Music CD
≥ Operation and sound quality of CDs that do not
comply with CD-DA specifications (copy control
CDs, etc.) cannot be guaranteed to work.
≥ The digital audio content side of a DualDisc
does not meet the technical specifications of
the Compact Disc Digital Audio (CD-DA) format
so playback may not be possible.
∫ SD card
≥ miniSD Cards, microSD Cards,
microSDHC Cards and
microSDXC Cards can be used,
but must be used with an adaptor
card.
≥ To protect the card’s contents,
move the record prevention tab (on
the SD card) to “LOCK”.
≥ This unit is compatible with SD Memory Cards
that meet SD Card Specifications FAT12 and
FAT16 formats, as well as SDHC Memory
Cards in FAT32 format and SDXC Memory
Cards in exFAT.
≥ If the SD card is used with incompatible
computers or devices, recorded contents may
be erased due to the card being formatted etc.
≥ Usable memory may be slightly less than the
card capacity.
≥ For playback of 4K videos stored on an SD
card, use an SD card conforming to Class 10 of
the SD Speed Class Rating.
∫ USB device
≥ This unit does not guarantee connection with all
USB devices.
≥ This unit does not support USB device
charging.
≥ FAT12, FAT16, FAT32, and NTFS file systems
are supported.
≥ This unit supports USB2.0 High Speed.
≥ This unit supports an HDD formatted in FAT32
and NTFS. If the HDD is not recognized, the
power to the HDD may not be supplied. Supply
power from an external source.
≥ It may not be possible to play the above media in some
cases due to the type of media, the condition of the
recording, the recording method, and how the files were
created.
≥ The producers of the disc can control how discs are
played, so you may not always be able to control play as
described in this Owner’s Manual. Read the disc’s
instructions carefully.
TQBA2018
7
Getting started
∫ Types of discs that cannot be
played by this unit
DMP-UB900_P-TQBA2018.book 8 ページ 2016年11月23日 水曜日 午後12時29分
Control reference guide
∫ Remote control
When other Panasonic devices respond to the
remote control of the unit, change the remote
control code. (> 34)
16
1
1
2
3
4
5
6
17
2
7
8
3
4
18
19
20
5
21
6
7
9
10
11
12
13
14
15
16
17
22
8
18
19
20
9
10
11
12
23
24
25
13
14
15
26
27
28
21
22
23
24
25
26
27
28
8
TQBA2018
Turn the unit on and off
Open or close the disc tray (> 9)
Select title numbers, etc./Enter numbers or
characters
Show Netflix screen (> 22)
Show Pop-up menu (> 20)
[3, 4, 2, 1] : Move the highlight for
selection
[OK] : Confirm the selection
(2;)(;1) : Frame-by-frame (> 20)
Show Option menu (> 26)
Colored buttons (red, green, yellow, blue)
Used for various purposes depending on the
screen
Basic playback control buttons (> 19)
Show Closed Caption setup screen (> 27)
Show “Playback Information Window” (> 20)
Show the status messages (> 20)
Show “Video Settings” (> 27)
Switch the “Sound Effects” setting (> 28)
Light up the remote control buttons
Transmit the remote control signal
TV operation buttons (> 18)
You can operate the TV through the unit’s
remote control. Some buttons may not work
depending on the TV.
Cancel
Show HOME menu (> 19)
Show the Home screen of the Network
Service (> 22)
Show Top menu (> 20)
Return to previous screen
Start up the DLNA function (> 24)
Show “Subtitle”/“Subtitle Settings” (> 26)
Change soundtrack (> 20)
Show MiracastTM screen (> 23)
Switch the “High Clarity Sound” settings
(> 28)
Switch the brightness of the unit’s display
(> 34)
DMP-UB900_P-TQBA2018.book 9 ページ 2016年11月23日 水曜日 午後12時29分
Getting started
∫ Front
7
6
Pull to flip down
the front panel.
1
1
2
3
4
5
2
3
4 5
Disc tray
Display
SD card slot
When removing the SD card, press the center
of the card and pull it straight out.
USB port (
DC 5 V 500 mA)
Remote control signal sensor
Distance: Within approx. 7 m (23 feet)
Angle: Approx. 20e up and down, 30e left and
right
6
7
Open or close the disc tray*
Standby/on switch* (Í/I) (> 17)
Touch to switch the unit from on to standby
mode or vice versa. In standby mode, the unit
is still consuming a small amount of power.
* These buttons work just by touching the marks.
Do not place any objects on or around the buttons.
CAUTION
Do not place objects in front of the unit. The disc tray may collide with objects when it is opened, and
this may cause malfunction.
≥ When inserting a media item, ensure that it is facing the correct way, which is the right side facing up.
≥ If you connect a Panasonic product with a USB connection cable, the setup screen may be displayed on the connected
equipment. For details, refer to the instructions for the connected equipment.
∫ Rear
8
1
1
2
3
4
5
6
AC IN ( ) terminal (> 10)
LAN port (> 16)
HDMI AUDIO OUT terminal (> 11)
HDMI VIDEO OUT terminal (> 10)
2ch AUDIO OUT terminals (> 12)
7.1ch AUDIO OUT terminals (> 12)
10
9
2
3
4
5
6
7
7
OPTICAL/COAXIAL terminal
(DIGITAL AUDIO OUT terminals) (> 12)
8 Cooling fan
9 HDMI OUT terminal
10 Analog AUDIO OUT terminals (> 12)
Class II equipment (The construction of the product is
double-insulated.)
TQBA2018
9
DMP-UB900_P-TQBA2018.book 10 ページ
2016年11月23日 水曜日 午後12時29分
Connecting to a TV
4K images can be played back when this unit is connected to 4K compatible TV.
≥ Before making any connections, please disconnect all the units from AC power.
(Connect the AC power supply cord after making all connections.)
≥ Use the High Speed HDMI cables. Non-HDMI-compliant cables cannot be utilized.
≥ Use HDMI VIDEO OUT terminal with an HDMI cable that supports 18 Gbps.
≥ This unit consumes a small amount of AC power (> 40) even when turned off in standby mode. For
the purpose of energy conservation, the unit should be disconnected if you will not be using it for
extended period of time.
∫ Enjoying 4K output
≥ To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
When outputting 1080p or 24p (4K) signal, please use HDMI cables 5.0 meters (16.4 ft.) or less.
It is recommended that you use Panasonic’s HDMI cable.
≥ If you connect this unit to a 4K-compatible TV and perform “Easy Setting”, 4K/60p will be
automatically selected. (> 17, 34)
≥ To view Ultra HD Blu-ray content in 4K/HDR format, connect to the HDMI terminal of a device that
supports HDCP2.2, 4K/60p (4:4:4), and HDR signals that meet Ultra HD Blu-ray standards.
Enjoying video and audio with a 4K-compatible TV
To an AC outlet
HDMI IN

AC power supply
cord (supplied)
HDMI cable*
≥ Insert the AC power supply cord up to A, a point just before the round hole.
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
10
TQBA2018
DMP-UB900_P-TQBA2018.book 11 ページ
2016年11月23日 水曜日 午後12時29分
Connecting to an amplifier/receiver
Getting started
Enjoying video with a 4K-compatible TV and audio with an amplifier
You can enjoy richer sound by using the HDMI AUDIO OUT terminal.
(Audio is output in high resolution.)
HDMI cable
HDMI cable*
HDMI IN
HDMI IN
Amplifier/receiver
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
≥ To enjoy audio with a TV:
Set “HDMI(VIDEO) Output Mode” to “Video+Audio”. (> 29)
≥ The HDMI AUDIO OUT terminal is not compatible with 4K output and the VIERA Link (> 25).
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
Enjoying video with a 4K-compatible TV and audio with a 4K-compatible amplifier
HDMI cable*
HDMI cable*
HDMI IN
HDMI OUT
(ARC)
HDMI IN
(ARC)
Amplifier/receiver
(4K-compatible)
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
≥ About ARC:
When using the TV or amplifier/receiver that does not have the indication of “(ARC)” (non-ARC-compatible) on the HDMI
terminal, the amplifier/receiver and TV must also be connected using an optical digital cable or coaxial cable in order to
enjoy the TV’s sound through the amplifier/receiver.
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
TQBA2018
11
DMP-UB900_P-TQBA2018.book 12 ページ
2016年11月23日 水曜日 午後12時29分
Enjoying audio with an amplifier connected to the DIGITAL AUDIO OUT/Analog AUDIO OUT
terminals
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
≥ To enjoy audio with an amplifier connected to the OPTICAL/COAXIAL terminal or 2ch AUDIO OUT
terminals:
Set “Audio Output” to “Off” in “Advanced Settings”. (> 30)
To enjoy audio with an amplifier connected to the 7.1ch AUDIO OUT terminals:
Set “Analog Multi Channel” to “On”. (> 31)
OPTICAL/COAXIAL (DIGITAL AUDIO OUT)
Coaxial cable
COAXIAL IN
OR
Optical digital cable
OPTICAL IN
Amplifier/receiver
2ch AUDIO OUT (Analog AUDIO OUT)
Connect terminals of the same color.
Audio cable
L
AUDIO IN
R
Amplifier/receiver
7.1ch AUDIO OUT (Analog AUDIO OUT)
Set the speaker presence and size according to your environment. (> 31)
(Audio is not output from HDMI OUT terminal.)
Connect Audio
cables to terminals
corresponding to
the speakers you
have connected.
Cable connections
A Front speaker (L/R)
B Surround speaker (L/R)
C Center speaker
12
TQBA2018
D Subwoofer
E Surround back speaker (L/R)
(Only for 7.1ch AUDIO OUT)
DMP-UB900_P-TQBA2018.book 13 ページ
2016年11月23日 水曜日 午後12時29分
HDMI cable*
HDMI cable
HDMI IN
HDMI IN
(ARC)
HDMI OUT
(ARC)
Amplifier/receiver
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
Enjoying video with a 4K-compatible TV in combination with an amplifier connected to the
HDMI AUDIO OUT terminal and another amplifier connected to the OPTICAL/COAXIAL/2ch
AUDIO OUT/7.1ch AUDIO OUT terminals
HDMI cable
HDMI cable*
HDMI IN
HDMI IN
Amplifier/receiver
Amplifier/receiver
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
≥ To enjoy audio with an amplifier connected to the OPTICAL/COAXIAL terminal or 2ch AUDIO OUT terminals:
Set “Audio Output” to “Off” in “Advanced Settings”. (> 30)
≥ To enjoy audio with an amplifier connected to the 7.1ch AUDIO OUT terminals:
Set “Analog Multi Channel” to “On”. (> 31)
≥ To enjoy audio with a TV:
Set “HDMI(VIDEO) Output Mode” to “Video+Audio”. (> 29)
≥ It is not possible to simultaneously output audio from both the amplifier connected to the HDMI AUDIO OUT terminal and the
other amplifier connected to the OPTICAL/COAXIAL/2ch AUDIO OUT/7.1ch AUDIO OUT terminals.
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
TQBA2018
13
Getting started
Connecting an amplifier to a 4K-compatible TV
3D or 4K images can be played back when this unit is connected to a 3D or 4K compatible TV.
≥ This connection only supports up to 5.1ch.
≥ To connect a TV and amplifier with an HDMI cable, connecting terminals on both the TV and amplifier
must be ARC-compatible. (> 11, “About ARC”)
DMP-UB900_P-TQBA2018.book 14 ページ
2016年11月23日 水曜日 午後12時29分
Enjoying video with a 4K-compatible TV in combination with a 2K-compatible projector and an
amplifier that is connected to the OPTICAL/COAXIAL/2ch AUDIO OUT/7.1ch AUDIO OUT
terminals
HDMI cable
HDMI cable*
HDMI IN
HDMI IN
Projector
(2K-compatible)
Amplifier/receiver
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
≥ To enjoy audio with an amplifier connected to the OPTICAL/COAXIAL terminal or 2ch AUDIO OUT
terminals:
Set “Audio Output” to “Off” in “Advanced Settings”. (> 30)
≥ To enjoy audio with an amplifier connected to the 7.1ch AUDIO OUT terminals:
Set “Analog Multi Channel” to “On”. (> 31)
≥ To enjoy audio with a TV:
Set “HDMI(VIDEO) Output Mode” to “Video+Audio”. (> 29)
Set “Audio Output” to “On” in “Advanced Settings”. (> 30)
≥ To enjoy video with a projector:
Set “HDMI(AUDIO) Output Mode” to “Video+Audio”. (> 29)
(It is not possible to output 3D, 4K or HDR content from the HDMI OUT terminal when “Video+Audio”
is selected.)
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
14
TQBA2018
2016年11月23日 水曜日 午後12時29分
Enjoying video with a 4K-compatible TV in combination with a 2K-compatible projector and an
amplifier that is connected to the HDMI AUDIO OUT terminal and another amplifier that is
connected to the OPTICAL/COAXIAL/2ch AUDIO OUT/7.1ch AUDIO OUT terminals
HDMI cable
HDMI OUT
HDMI cable*
HDMI IN
HDMI IN
Amplifier/receiver
HDMI IN
Amplifier/receiver
HDMI cable
Projector
(2K-compatible)
Setting
Set the following items in the setup menu (> 29):
≥ Set “HDMI(VIDEO) Output Mode” to “Auto ( Video Only / Video+Audio )”. (> 29)
≥ Set “HDMI(AUDIO) Output Mode” to “Audio Only”. (> 29)
≥ To enjoy audio with an amplifier connected to the OPTICAL/COAXIAL terminal or 2ch AUDIO OUT
terminals:
Set “Audio Output” to “Off” in “Advanced Settings”. (> 30)
≥ To enjoy audio with an amplifier connected to the 7.1ch AUDIO OUT terminals:
Set “Analog Multi Channel” to “On”. (> 31)
≥ To enjoy audio with a TV:
Set “HDMI(VIDEO) Output Mode” to “Video+Audio”. (> 29)
≥ To enjoy video with a projector:
Set “HDMI(AUDIO) Output Mode” to “Video+Audio”. (> 29)
(It is not possible to output 3D, 4K or HDR content from the HDMI OUT terminal when “Video+Audio”
is selected.)
≥ It is not possible to simultaneously output audio from both the amplifier connected to the HDMI AUDIO OUT terminal and the
other amplifier connected to the OPTICAL/COAXIAL/2ch AUDIO OUT/7.1ch AUDIO OUT terminals.
* To enjoy images in 4K/60p, you need an HDMI cable that supports 18 Gbps.
TQBA2018
15
Getting started
DMP-UB900_P-TQBA2018.book 15 ページ
DMP-UB900_P-TQBA2018.book 16 ページ
2016年11月23日 水曜日 午後12時29分
Connecting to the network
The following services can be used when this unit is connected to broadband.
≥ Firmware can be updated (> 18)
≥ You can enjoy Ultra HD Blu-ray/BD-Live/Network Service (> 21, 22)
≥ You can access other devices (Home Network) (> 23)
≥ This unit supports Wi-Fi Direct® and can make a wireless connection to wireless devices without
router. You can use this function when enjoying Home Network feature, etc. Internet access is not
available while connected via Wi-Fi Direct®. (> 24)
For details about connection method, refer to the instructions supplied with the connected equipment.
Wireless LAN connection
This unit has built-in Wi-Fi® and can be connected to a wireless router.
Wireless router, etc.
Internet
≥ For additional information about this unit refer to
http://shop.panasonic.com/support
≥ The unit is not compatible with public wireless LAN services.
≥ See page 3 for the precautions of wireless LAN connection.
LAN cable connection
LAN Cable
Broadband router, etc.
Internet
≥ Use category 5e or above straight LAN cables (STP) when connecting to peripheral devices.
≥ Inserting any cable other than a LAN cable in the LAN port can damage the unit.
16
TQBA2018
DMP-UB900_P-TQBA2018.book 17 ページ
2016年11月23日 水曜日 午後12時29分
Settings
Easy Network Setting
Select a connection mode.
Getting started
The following settings can be performed anytime
in the Setup menu. (> 32, 34)
Easy Setting
After connecting your new player for the first time
and pressing [Í], the basic settings screen will
appear.
Preparation
Turn on the TV and select the appropriate
video input.
1
Press [Í].
Setup screen appears.
2
Follow the on-screen instructions to
continue with the settings.
(e.g., “Quick Start”)
≥ Certain recent models of Panasonic TVs
(VIERA) may automatically apply their
language setting to this unit.
∫ When connected to a
4K/60p-compatible TV
When connected to a 4K/60p-compatible TV, you
can set the video output format.
4K60p Output
Press OK to start the connection check with your 4K TV.
Do not operate this unit during connection check.
Notice: Connection check might take up to 30 seconds and video
might appear distorted.
Start
OK
Wired
Wireless
OK
RETURN
∫ About the wireless connection
To obtain your network name (SSID*) and
encryption key (password).
e.g.
The default settings may be
printed on the router. If the SSID
and password have been
changed, consult the person
responsible for setting up your
network.
SSID XXXXXXXXXXXX
KEY XXXXXXXXXXXX
PIN XXXXXXXXX
For more details, refer to the
manual supplied with the wireless broadband
router, or contact your Internet provider.
If your SSID is not displayed;
Search again by pressing the red button on the
remote control.
Wireless Settings
Select a wireless network for connection.
Press the green button to connect via
WPS (PUSH button method).
Network name (SSID)
Reception
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
RETURN
Follow the on-screen instructions to set the
format.
Search again
WPS (PUSH)
OK
RETURN
≥ To reconnect this unit to a 4K/60p-compatible TV after
connecting this unit to a 2K-compatible TV and completing
“Easy Setting”, set “4K60p Output” to “4K/60p(4:4:4)” or
“4K/60p(4:2:0)”. (> 29)
Easy Network Setting
After completing “Easy Setting”, you can perform
“Easy Network Setting”.
Select “Wired” or “Wireless” and press [OK].
Stealth SSIDs will not be displayed; in this case,
enter manually in the following order.
1 To display the SSID input screen :
Press [HOME]
> select [OK] to select “Setup”
> select “Player Settings” and press [OK]
> select “Network” and press [OK]
> select “Network Settings” and press [OK]
> select “Wireless Settings” and press [OK]
> select “Manual setting” and press [OK]
2 Enter your SSID.
≥ If your wireless network is encrypted, go to
page 18.
TQBA2018
17
DMP-UB900_P-TQBA2018.book 18 ページ
2016年11月23日 水曜日 午後12時29分
If your wireless router supports WPS (Wi-Fi
Protected SetupTM);
You can easily set up a connection by pressing
the green button on the remote control.
You cannot operate the unit until the update is
complete. Don’t remove the AC power supply
cord during the update. Removing the AC power
supply cord while the update is in progress may
damage the unit.
If your wireless network is encrypted;
Enter your encryption key (password).
≥ You can switch between capital and lower case
letters by pressing the “Shift” key.
After the firmware is installed, “FINISH” will be
displayed on the unit’s display. Unit will restart
and the following screen will be displayed.
2
The firmware was updated.
Current Version: x.xx
Encryption Key (Password)
l
1
Shift
2
3
4
5
6
7
8
9
0
Delete
Finish
.
Space
/
:
Symbols
OK
~
_
-
@
*
#
;
`
“
,
Alphanumeric
≥ You can also download the latest firmware from the
following website and store it to a USB device to
update the firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
≥ To show the firmware version on this unit. (> 34,
“Firmware Version Information”)
≥ Downloading will require several minutes. It may take
longer or may not work properly depending on the
connection environment.
Other Characters
(QWHUFDVHVHQVLWLYH
RETURN
*1
≥ Refer to the owner’s manuals of the hub or router.
≥ Do not use this unit to connect to any wireless network for
which you do not have usage rights.
Using these networks may be regarded as illegal
access.
≥ If you have trouble getting online on your PC after
performing network settings on this unit, perform the
network settings on your PC.
≥ Please be aware that connecting to a network without
encryption may result in the leaking of data such as
personal or secret information.
* An SSID (Service Set IDentification) is a name used by
wireless LAN to identify a particular network. Transmission
is possible if the SSID matches for both devices.
*2
You must agree to the terms of use for the Internet function
and the privacy policy. (> 33, “Notice”)
“X.XX” represents the firmware version number.
Reprogramming the
remote control
You can operate the TV using the unit’s remote
control.
1
Input the 2-digit code (> 42) while
pressing [Í] of TV operation button on the
remote control.
e.g., 01: [0] B [1]
2
Test by turning on the television.
Firmware updates
This unit is capable of checking the firmware
automatically when connected to the Internet via
a broadband connection.*1
When a new firmware version is available, the
following message is displayed.
2
Firmware Update
New Version: X.XX
Current Version: X.XX
Do you want to start firmware update?
For the update information, please visit the
following website:
http://panasonic.net/support/
Yes
No
OK
RETURN
18
TQBA2018
≥ If your television brand has more than one code listed,
select the one that allows correct operation.
HOME menu
Playback
Major functions of this unit can be operated from
the HOME menu.
1
Preparation
Turn on the TV and select the appropriate video input.
2
Playback
1
Playback starts depending on the media.
2
Press [OK] or [2, 1] to select the item.
≥ Press [OK] or [3, 4] to select the item if
necessary.
Select the item to play and press [OK].
Repeat this step if necessary.
Press [Í] to turn on the unit.
It may take some time until the HOME menu
is displayed.
Insert the media.
≥ DISCS CONTINUE TO ROTATE WHILE MENUS ARE
DISPLAYED. Press [∫] when you have finished playback
to protect the unit’s motor, your TV screen and so on.
≥ When the following conditions are met, still pictures are
played back in 4K regardless of the image quality.
– The unit is connected to a 4K compatible TV
– “Resolution” is set to “Auto” or “4K” (> 29)
≥ This unit can not output 4K images when playing back in
3D.
≥ It is not possible to play back AVCHD and MPEG2 videos
which have been dragged and dropped or copied and
pasted to the media.
≥ To enjoy BD-Video that supports Dolby Atmos® or DTS:XTM
(> 31)
Operations during playback
Videos/Music/Photos
Disc
SD Card
USB
Play back the contents.
(> right)
≥ When multiple contents are
recorded, select the types
of contents or the title.
Home Network
DLNA Client
(> 24)
Miracast
(> 23)
Media Renderer (> 24)
Network Service
Displays the Home screen of Network Service.
(> 22)
Some operations may not work depending on the
media and contents.
Stop
Press [∫].
The stopping point is memorized.
Resume play function
Press [1] to restart from this point.
≥ The point is cleared if the media is removed.
≥ On BD-Video discs including BD-J, the
resume play function does not work.
Pause
Press [;].
≥ Press [;] again or [1] to restart play.
Setup
Player Settings (> 29)
Changes the background of
Wallpaper
HOME menu.
SD Card
(> 21)
Management
To show the HOME menu
Press [HOME].
≥ Items to be displayed may vary with the media.
≥ See “Playable media” (> 6)
TQBA2018
19
Getting started
2016年11月23日 水曜日 午後12時29分
Playback
DMP-UB900_P-TQBA2018.book 19 ページ
DMP-UB900_P-TQBA2018.book 20 ページ
2016年11月23日 水曜日 午後12時29分
Search/Slow motion
Search
While playing, press [6] or [5].
≥ Ultra HD Blu-ray, MKV, MP4 and MPEG2:
Audio is not heard. (When “Voice Guidance
Setting” is set to “On”, audio is not heard
regardless of the media.)
Slow motion
While paused, press [6] or [5].
≥ BD-Video and AVCHD: [5] only.
≥ MKV, MP4 and MPEG2: Not effective.
The speed increases up to 5 steps.
≥ Music, MP3, etc.: The speed is fixed to a single
step.
≥ Press [1] to revert to normal playback speed.
Skip
While playing or paused, press [:] or
[9].
Skip to the title, chapter or track.
Show the status messages
While playing, press [PLAYBACK INFO.].
You can check the detailed disc playback status.
Video attribute information of disc.
Audio attribute information of disc.
HDMI(VIDEO) output information.
HDMI(AUDIO) output information.
Press [RETURN] to exit.
While playing, press [STATUS].
The status messages give you information about
what is currently being played. Each time you
press [STATUS], the display information may
change or disappear from the screen.
≥ Depending on media and contents, the display
may change or not appear.
e.g., BD-Video
A
Frame-by-frame
T1
While paused, press [2] (2;) or [1] (;1).
≥ Each press shows the next frame.
≥ Press and hold to change in succession forward
or backward.
≥ Press [1] to revert to normal playback speed.
≥ BD-Video and AVCHD: Forward only.
≥ MKV, MP4 and MPEG2: Not effective.
Changing soundtrack
Press [AUDIO].
You can change the audio channel number or
soundtrack language, etc.
Show top menu/pop-up menu
Press [TOP MENU] or [POP-UP MENU].
Select the item and press [OK].
C1
Play
D
A
B
C
D
T: Title, C: Chapter, PL: Playlist
Elapsed time in the title
Current position
Total time
e.g., JPEG
Date
11/12/2010
Size
500 x 375
Manufacturer
Equipment
TQBA2018
No.
≥ During music playback, the elapsed time, file
name and other relevant information are
displayed on the unit’s display.
e.g., MP3
20
BD-Video
2016年11月23日 水曜日 午後12時29分
Enjoying Ultra HD Blu-ray
You can enjoy the playback of Ultra HD Blu-ray
discs with this unit.
Preparation
≥ For 4K/HDR viewing, connect to a device and
terminals that support HDCP2.2*1, 4K/60p
(4:4:4) and HDR signals that meet Ultra HD
Blu-ray standards. (> 10)
≥ Network connection (> 16)
≥ Network setting (> 17)
Due to copyright restrictions, it may not be
possible to play back certain discs unless this
unit is connected to the Internet.
≥ When connected to a device or terminal that does not
support HDCP2.2*1, this unit applies Dynamic Range
Conversion*2 to HDR signals to output them in 2K
resolution. In addition, depending on the disc, it may not be
possible to perform playback correctly.
≥ When connected to a device or terminal that supports 4K/
60p (4:2:0/8 bit) and lower, this unit plays back 60p content
by applying Dynamic Range Conversion*2 to its HDR
signals to output them.
≥ When connected to a device or terminal that does not
support 4K resolution, this unit applies Dynamic Range
Conversion*2 to HDR signals to output them in 2K
resolution.
≥ When connected to a device or terminal that does not
support HDR, this unit applies Dynamic Range
Conversion*2 to HDR signals to output them. In addition,
depending on the disc, it may not be possible to output
content in 2K resolution or perform playback correctly.
≥ For details on the playback of Ultra HD Blu-ray content,
refer to the website below.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
*1
*2
HDCP is a technology designed to prevent illegal copying.
“2.2” represents a version.
Dynamic Range Conversion is a function that converts
HDR video signals into video signals suited to TVs that do
not support HDR input.
Enjoying 3D video and photos
Preparation
Connect this unit to a 3D compatible TV. (> 10)
≥ Perform the necessary preparations for the TV.
≥ Play back following the instructions displayed
on the screen.
≥ 3D Settings (> 28, 32)
≥ Please refrain from viewing 3D images if you do not feel
well or are experiencing visual fatigue.
In the event that you experience dizziness, nausea, or
other discomfort while viewing 3D images, discontinue use
and rest your eyes.
≥ 3D video might not output the way it is set in “Resolution”
and “24p Output” (> 29).
≥ When playing back 3D photos from “Photos” screen, select
from the “3D” list. (Still pictures in “2D” are played back in
2D.)
If “2D” and “3D” indications are not displayed, press the
red button on the remote control to switch the view of
playback contents.
Enjoying BD-Live
With “BD-Live” discs, you can enjoy bonus
contents that use Internet access.
For this BD-Live function, insertion of an SD card
is necessary along with Internet connection.
1
Perform network connection and settings.
(> 16, 17)
2
Insert an SD card with 1 GB or more free
space.
≥ The SD card is used as the local storage.
3
Insert the disc.
∫ Deleting data/Formatting SD
cards
Select “SD Card Management” in the HOME
menu (> 19), then select “BD-Video Data
Erase” or “Format SD Card”.
≥ The usable functions and the operating method may vary
with each disc, please refer to the instructions on the disc
and/or visit their website.
≥ “BD-Live Internet Access” may need to be changed for
certain discs. (> 33)
TQBA2018
21
Playback
DMP-UB900_P-TQBA2018.book 21 ページ
DMP-UB900_P-TQBA2018.book 22 ページ
2016年11月23日 水曜日 午後12時29分
Slideshow
Play a slideshow of photos and adjust various
settings during the playback.
1
2
3
Insert the media.
Select “View Photos”.
Select an item and press the green button.
The following items can be set.
Start
Slideshow
Start the slideshow.
You can display still pictures in
the selected folder one by one
at a constant interval.
Display
Interval
Change the display interval.
Transition
Effect
Select the effect when sliding
pictures.
Repeat Play
Set whether to repeat the
slideshow.
Soundtrack
Set whether to play
background music.
≥ FLAC and MP3, etc., on the
USB device can be played
back during the slideshow of
JPEG on the USB device or
the SD card.
≥ A music CD can also be
played back during the
slideshow of JPEG on the
SD card.
Soundtrack
Folder
Select the folder from which
the music files are played.
Random
Soundtrack
Background music is played in
random order.
≥ Still pictures displayed as “
” cannot be displayed as
thumbnail with this unit.
≥ When both the music CD and the USB device with
recorded music are inserted into this unit, the music CD
has priority to be played back as background music.
≥ You cannot play back AAC and ALAC as background
music.
22
TQBA2018
Network Service
(Enjoying Netflix, etc.)
Network Service allows you to access some
specific websites supported by Panasonic, and
enjoy Internet contents such as photos, videos,
etc. from Network Service home screen.
≥ Some services, such as Netflix require a
registered account.
For details of your Netflix account, refer to Netflix.
*
MORE
BACK
* Images are for illustration purposes, contents may change
without notice.
Preparation
≥ Network connection (> 16)
≥ Network setting (> 17)
– You must agree to the terms of use for the Internet
function and the privacy policy. (> 33, “Notice”)
1
Press [INTERNET].
≥ Netflix can be accessed directly by
pressing [NETFLIX] button.
2
Select the item and press [OK].
To exit from Network Service
Press [HOME].
2016年11月23日 水曜日 午後12時29分
≥ In the following cases, settings are possible using the
Setup menu items.
– When restricting the use of Network Service
(> 33, “Network Service Lock”)
– When the audio is distorted
(> 33, “Audio Auto Gain Control”)
– When wrong time is displayed
(> 33, “Time Zone”, “DST”)
≥ When using a slow Internet connection, the video may not
be displayed correctly. A high speed Internet service with a
speed of at least 6 Mbps is recommended.
≥ Be sure to update the firmware as soon as a firmware
update notice is displayed on the screen. If the firmware is
not updated, you may not be able to use Network Service
function properly. (> 18)
≥ Network Service Home Screen is subject to change
without notice.
≥ The services through Network Service are operated by
their respective service providers, and service may be
discontinued either temporarily or permanently without
notice. Therefore, Panasonic will make no warranty for the
content or the continuity of the services.
≥ Some features of websites or content of the service may
not be available.
≥ Some content may be inappropriate for viewers.
≥ Some content may only be available for specific countries
and may be presented in specific languages.
Home Network feature
Before using the following features, be sure to
configure the connected equipment on your
Home Network.
Using MiracastTM
You can enjoy the content you are viewing on a
Miracast-compatible smartphone, etc. on the big
screen of your TV.
≥ Compatible with AndroidTM devices, ver. 4.2 and
above and Miracast certified.
For information on whether the smartphone,
etc. supports Miracast, contact the
manufacturer of the device.
Player
1
2
Miracast compatible
device
Press [MIRACAST].
Operate the Miracast compatible device.
≥ On the device, enable Miracast and select
this unit (DMP-UB900) as the device to be
connected.
For details, refer to the instructions supplied
with the device.
To exit from Miracast
Press [HOME].
TQBA2018
23
Playback
DMP-UB900_P-TQBA2018.book 23 ページ
DMP-UB900_P-TQBA2018.book 24 ページ
2016年11月23日 水曜日 午後12時29分
Playing back contents on the
DLNA server
You can share photos, videos and music stored in
the DLNA Certified media server [PC,
smartphone, etc.] connected to your home
network.
Using the Digital Media
Controller
You can use a smartphone or tablet as the Digital
Media Controller (DMC) to playback contents
from DLNA server on the Renderer (this unit).
Possible applications:
≥ About support format of DLNA (> 41)
Renderer
Player
1
*
Press [DLNA].
≥ The list can be updated by pressing the red
button on the remote control.
≥ The connection method can be switched to
Wi-Fi Direct by pressing the green button
on the remote control.
2
3
Controller
Server
*
Server
Select the equipment and press [OK].
Select the item to play and press [OK].
≥ You may be able to use convenient
functions depending on the content by
pressing [OPTION].
To exit from Home Network
Press [HOME].
Renderer
Server
i
Controller
*
* DMC compatible software should be installed.
Preparation
Perform the “Remote Device Settings”. (> 33)
≥ You can register up to 16 devices.
1
2
3
4
Press [HOME].
5
Operate the DMC compatible devices.
Select “Home Network” and press [OK].
Select “Media Renderer” and press [OK].
Select “Home Network” or “Wi-Fi Direct”
and press [OK], then follow the indications
on the screen.
To exit from Media Renderer screen
Press [HOME].
≥ Wi-Fi Direct connection while using Home Network feature
is only temporary, and the network connection method
returns to the original setting when exiting.
≥ Depending on the device or connection environment, the
data transfer rate may decrease.
≥ Depending on the contents and the connected equipment,
playback may not be possible.
≥ Items displayed in gray on the display cannot be played
back by this unit.
24
TQBA2018
2016年11月23日 水曜日 午後12時29分
VIERA Link
Playing music continuously
even after turning off the TV
What is VIERA Link?
VIERA Link is a convenient function
which will link the operations of this unit
and a Panasonic TV (VIERA) or other
device under “VIERA Link”.
You can use this function by connecting
the equipment with an HDMI cable*. See
the owner’s manuals for connected
equipment for operational details.
* Only when connecting via an HDMI VIDEO OUT terminal
on this unit.
Automatic input switching
Power on link
When the following operations are performed, the
input channel of the TV will be automatically
switched and the screen of this unit will be
displayed.
If this unit is on and the TV is off, the TV
automatically turns on.
– When play starts on the unit
– When you display a menu, such as the HOME
menu or Setup menu
Power off link
When you set the TV to standby mode, this unit is
also automatically set to standby mode.
When the unit is connected to a Panasonic TV
(VIERA) that supports VIERA Link and an
amplifier/receiver supports VIERA Link.
1 While playing music
Press [OPTION].
2 Select “TV Power”.
Easy control only with VIERA
remote control
Only when TV supports “VIERA Link”
By using the TV remote control, you can perform
various playback operations and settings.
See the owner’s manuals of the TV for more
details.
≥ If you set “VIERA Link” to “Off”, set to “On” (> 34).
(The default setting is “On”.)
≥ The buttons and functions that you can use for this unit
vary depending on the TV. For details, refer to the owner’s
manuals of the TV.
≥ The operation of this unit may be interrupted when you
press certain buttons on the TV remote control.
≥ VIERA Link, based on the control functions provided by
HDMI which is an industry standard known as HDMI CEC
(Consumer Electronics Control), is a unique function that
we have developed and added. As such, its operation with
other manufacturers’ equipment that supports HDMI CEC
cannot be guaranteed.
≥ Please refer to individual manuals for other manufacturers’
equipment supporting VIERA Link function.
TQBA2018
25
Playback
DMP-UB900_P-TQBA2018.book 25 ページ
DMP-UB900_P-TQBA2018.book 26 ページ
2016年11月23日 水曜日 午後12時29分
Option menu
A variety of playback operations and settings can
be performed from this menu.
Available options differ depending on the playing
contents and the condition of the unit.
1
Press [OPTION].
∫ Shuffle
Select whether or not to play random.
e.g., BD-Video
Operation Menu
Soundtrack
∫ Repeat Play
Select the item that you want to repeat.
≥ You can repeat the playback of a chapter,
playlist, the entire disc, etc., but the items
displayed will differ depending on the type of
the media.
≥ Select “Off” to cancel.
1 ENG DTS-HD MSTR Multi
Subtitle Settings
Angle
1
Repeat Play
Off
Secondary Video
Playback Information Window
Control Panel
∫ Start Slideshow
Start the slideshow.
∫ Status
Show the status messages.
Top Menu
Pop-up Menu
Closed Caption
≥ When playing music, select “Playback
Settings” and press [OK].
2
Select an item and change the settings.
∫ Rotate Right
∫ Rotate Left
Rotate the still picture.
∫ Wallpaper
Set the still picture to the wallpaper of HOME
menu. (> 19)
To exit the screen
Press [OPTION].
∫ Video
The recording method of original video appears.
Regarding Language : (> 42)
∫ Secondary Video
Operation Menu
∫ Soundtrack (> 20)
This setting is also able to switch by pressing
[AUDIO].
∫ Audio channel
Select the audio channel number.
∫ Subtitle
∫ Subtitle Settings
Change the subtitle settings.
This setting is also displayed by pressing
[SUBTITLE].
Video
Select on/off for images. The
recording method of original
video appears.
Soundtrack
Select on/off for audio and the
language.
∫ Playback Information Window (> 20)
This setting is also displayed by pressing
[PLAYBACK INFO.].
∫ Control Panel
Display the Control Panel.
Playing back while using VIERA Link, etc.
e.g.,
∫ Angle
Select the number of the angle.
Press [RETURN] to hide the Control Panel.
26
TQBA2018
DMP-UB900_P-TQBA2018.book 27 ページ
2016年11月23日 水曜日 午後12時29分
∫ Top Menu
Display Top Menu.
∫ Noise Reduction
Reduce unnecessary noise in videos. The greater the value is, the less noise will appear.
∫ Pop-up Menu
Display Pop-up Menu.
∫ Luminance/Color Adjustment
Adjust the contrast, brightness, white gamma,
black gamma, color saturation and hue.
∫ Closed Caption (> 32)
You can only set “Manual setting” and “CC Reset”
in the Setup menu.
These settings are also displayed by pressing
[CC].
∫ Reception
The radio wave status during the playback of
DLNA is displayed. (Only when a wireless
connection is used)
Video Settings
These settings are also displayed by pressing
[VIDEO SETTING].
Video Settings
Set 1
Normal
Display
Picture Type
entt
Sharpness Adjustment
Noise Reduction
During BD-Video playback,
these icons switch to the ones
for BD Video content.
Normal
jusstment
Luminance/Color Adjustment
Bandwidth Limitationn
24p Conversion
Progressive
Off
Auto
Reset to Default Video
eo
o Settings
Set 1
Switch “Set 1”, “Set 2” or “Standard” by using
[2, 1].
≥ You can register desired settings to “Set 1” and
“Set 2”. Settings for BD Video playback and
settings for the playback of other types of media
are registered separately.
(The default settings for “Set 1”/“Set 2” are the
same as the settings for “Standard”.)
≥ You cannot change the “Standard” settings.
∫ Bandwidth Limitation
Adjust the bandwidth limitations.
∫ Dynamic Range Conversion Adjustment
When this unit is connected to a TV that does not
support HDR (High Dynamic Range) input, HDR
video is output converting to a SDR (Standard
Dynamic Range) video signal. If you set a smaller
value, their contrast will be reproduced more
faithfully, but the entire screen will appear darker.
To increase the brightness, set a larger value.
∫ 24p Conversion
Play back videos with film-like motion.
≥ When this unit is connected to a TV compatible
with 4K/24p:
If “Resolution” (> 29) is set to “Auto” or “4K”,
videos will be output in 4K/24p.
≥ When this unit is connected to a TV compatible
with 1080/24p:
If “Resolution” (> 29) is set to “Auto”, “1080i” or
“1080p”, videos will be output in 1080/24p.
≥ Noise may appear on the image when you
switch the setting.
∫ Progressive
Select the method of conversion for progressive
output to suit the type of material being played.
≥ When the content is distorted, change the
settings from “Auto” to “Video”.
∫ Reset to Default Video Settings
Return “Video Settings” of the selected tab
(“Set 1” or “Set 2”) to the factory preset.
∫ Display
Select a setting suitable for your screen.
∫ Picture Type
Select the picture quality mode during play.
∫ Sharpness Adjustment
Adjust the sharpness of images. The greater the
value is, the sharper images will be.
TQBA2018
27
Playback
∫ Menu
Display Menu.
DMP-UB900_P-TQBA2018.book 28 ページ
2016年11月23日 水曜日 午後12時29分
Sound Effect Settings
∫ Sound Effects*1, *2
Select the sound effect.
This setting is also able to switch by pressing
[SOUND EFFECT].
≥ Night Surround :
Enjoy a movie with powerful sound even when
the volume is kept low at night. The audio is set
in such a way that it can be heard easily.
≥ Re-master :
This feature gives you brighter sound by
increasing the high frequency portion of the
audio.
(Upsampling up to 192 kHz/32 bit is possible.)
Recommended setting
Re-master 1
Pop and rock
Re-master 2
Jazz
Re-master 3
Classical
≥ When “Voice Guidance Setting” is set to “On”,
the re-mastering function is disabled. (> 31)
≥ Digital Tube Sound :
This feature gives you a warm sound, like that
produced by a vacuum tube amplifier.
(Upsampling up to 192 kHz/32 bit is possible.)
Recommended setting
Digital Tube
Sound 1
A crisp, delicate sound
Digital Tube
Sound 2
A tight, hi-fi sound
Digital Tube
Sound 3
A soft, rich sound
Digital Tube
Sound 4
A clear, powerful sound
Digital Tube
Sound 5
A distinctive mid-range
sound
Digital Tube
A soft, enveloping sound
Sound 6
≥ When “Voice Guidance Setting” is set to “On”,
the maximum upsampling frequency will be
fixed at 48 kHz. (> 31)
∫ Sound Effect Frequency
Set the maximum sampling frequency for the
audio selected in “Sound Effects”.
≥ Even when “96/88.2kHz” is selected, an audio
source with a sampling frequency of 96 kHz or
higher will be output with the original sampling
frequency.
≥ When “Sound Effects” is set to “Off”, this setting
is disabled.
∫ DSD Decode Sampling Frequency
Select the settings that suit your sound quality
preferences.
∫ DSD LPF Setting
Select the settings that suit your sound quality
preferences.
*1
*2
Not every function can be set individually.
This function is effective for audio from HDMI OUT or
DIGITAL AUDIO OUT only when “Digital Audio Output” is
set to “PCM” (> 30).
Audio Settings
∫ Dialog Enhancer*
The volume of the center channel is raised to
make dialog easier to hear.
∫ High Clarity Sound
Stop processing signals that affect the audio
quality or turn off the unit’s display to make the
audio quality clearer. (> 31)
Select whether or not to output images.
This setting is able to switch by pressing [HIGH
CLARITY].
≥ If “On (Video Off)” is selected, the setting will be
canceled after you play back a video.
* This function is effective for audio from HDMI OUT or
DIGITAL AUDIO OUT only when “Digital Audio Output” is
set to “PCM” (> 30).
3D Settings
∫ Signal Format
Original
Keep original picture format.
Side by side
3D picture format comprising
of left and right screens.
∫ Pop-Out Level
3D position for the Option menu or message
screen, etc. can be adjusted during 3D playback.
28
TQBA2018
Setup menu
Reference
Change the unit’s settings if necessary. The
settings remain intact even if you switch the unit
to standby.
Some items are common to the Option menu. You
can get the same effect with both menus.
1
Press [HOME].
2
Select “Setup”.
3
Select “Player Settings”.
Player Settings
Resolution
HDMI
4K60p Output
Auto
Off
Video
24p Output
Auto
Audio
HDMI(VIDEO) Output Mode
Auto
HDMI(AUDIO) Output Mode
Audio Only
3D
Advanced Settings
Language
Network
Ratings
System
OK
RETURN
4
∫ 4K60p Output
This unit automatically chooses to output images
in 4K*1 60p when connected to a 4K/60p
compatible TV.
≥ This item is available only when “Resolution” is
set to “Auto” and “4K”.
≥ This item is not available when “HDMI(AUDIO)
Output Mode” is set to “Video+Audio”.
≥ To connect to a TV that supports 4K/60p (4:4:4/
8 bit) or 4K/60p (4:2:2/12 bit), select “4K/
60p(4:4:4)”.
Images will not be output correctly with an
HDMI cable that does not support 18 Gbps.
≥ To connect to a TV that supports 4K/60p (4:2:0/
8 bit), select “4K/60p(4:2:0)”.
Select an item and change the settings.
To exit the screen
Press [HOME].
HDMI
∫ Resolution
The items supported by the connected devices
are indicated on the screen as “¢”. When any
item without “¢” is selected, the images may be
distorted.
≥ If “Auto” is selected, the best suited output
resolution to the connected TV is automatically
selected.
∫ 24p Output
Movies and other material recorded at 24p*2 are
output at 24p.
≥ When this unit is connected to TV compatible
with 4K/24p and “Resolution” is set to “Auto” or
“4K”, images will be output in 4K/24p.
≥ When this unit is connected to a TV compatible
with 1080/24p and “Resolution” is set to “Auto”,
“1080i” or “1080p”, images will be output in
1080/24p.
≥ If images output in 24p are distorted, change
the setting to “Off”.
∫ HDMI(VIDEO) Output Mode
Set whether or not to output audio from the HDMI
VIDEO OUT terminal.
≥ When an amplifier is connected to the HDMI
AUDIO OUT terminal and this menu item is set
to “Auto ( Video Only / Video+Audio )”, the TV
may not output audio. In that case, select
“Video+Audio”.
∫ HDMI(AUDIO) Output Mode
Set whether or not to output images from the
HDMI AUDIO OUT terminal.
≥ It is not possible to output 3D, 4K or HDR
content from the HDMI OUT terminal when
“Video+Audio” is selected.
TQBA2018
29
Playback
2016年11月23日 水曜日 午後12時29分
Reference
DMP-UB900_P-TQBA2018.book 29 ページ
DMP-UB900_P-TQBA2018.book 30 ページ
2016年11月23日 水曜日 午後12時29分
∫ Advanced Settings
Press [OK] to show the following settings:
¾Color Mode
This setting is for selecting color-space
conversion of the image signal.
¾Deep Color Output
This setting is for selecting whether to use Deep
Color Output when a TV that supports Deep
Color is connected.
¾High Dynamic Range Output
Output images in HDR (High Dynamic Range)
format depending on the content and connected
device.
¾Contents Type Flag
Depending on the playback content, the TV will
output adjusting to the optimal method when a
TV that supports this function is connected.
¾Audio Output
This setting selects whether or not to output
audio from HDMI.
≥ To enjoy audio with the HDMI terminal, select
“On”. To enjoy audio with an audio output
terminal other than the HDMI terminal
(OPTICAL/COAXIAL/2ch AUDIO OUT),
select “Off”. Audio will not be output from the
HDMI terminal regardless of the settings for
HDMI(VIDEO) Output Mode and
HDMI(AUDIO) Output Mode.
¾7.1ch Audio Reformatting
Surround sound with 6.1ch or less is
automatically expanded and played back at
7.1ch.
≥ If “Off” is selected, sound is played over the
original number of channels. (Note that in the
case of 6.1ch audio, playback will be at
5.1ch.)
≥ Audio reformatting is enabled in the following
cases:
– When you have selected “PCM” in “Digital
Audio Output”.
– When the audio is Dolby Digital, Dolby
Digital Plus, Dolby TrueHD or LPCM.
– BD-Video playback
*1
*2
A high resolution image/display technology of
approximately 4000 (width) k 2000 (height) pixels.
A progressive image recorded at a rate of 24 frames per
second (motion-picture film). Many BD-Video movie
contents are recorded in 24 frames/second in accordance
with the film materials.
30
TQBA2018
Video
∫ Still Mode ( paused video )
Select the type of picture shown when you pause
playback.
Auto
Automatically selects the type
of picture shown.
Field
Select if jittering occurs when
“Auto” is selected.
Frame
Select if small text or fine
patterns cannot be seen
clearly when “Auto” is
selected.
∫ Seamless Play
The chapter segments in playlists are played
seamlessly.
≥ Select “On” when the picture freezes for a
moment at the chapters segment in playlists.
Audio
∫ Dynamic Range Compression
You can listen at low volumes but still hear
dialogue clearly.
(Dolby Digital, Dolby Digital Plus and Dolby
TrueHD only)
≥ “Auto” is effective only when playing Dolby
TrueHD.
∫ Digital Audio Output
Press [OK] to show the following settings:
¾Dolby D/Dolby D +/Dolby TrueHD
¾DTS/DTS-HD
Select the audio signal to output.
≥ Select “PCM”, when the connected
equipment cannot decode the respective
audio format. This unit decodes the audio
format and transmits to the connected
equipment.
≥ If you do not make proper settings the audio
may be static or noisy.
≥ If you set “Voice Guidance Setting” to “On”,
these settings will be fixed to “PCM”.
2016年11月23日 水曜日 午後12時29分
¾BD-Video Secondary Audio
Select whether or not to mix the primary and
secondary audio (including the button click
sound).
If “Off” is selected, the unit outputs the primary
audio only.
≥ To enjoy BD-Video that supports Dolby Atmos® or
DTS:XTM
Connect this unit to an AV amplifier or similar device that
supports it with an HDMI cable, and select the following
settings:
– Dolby D/Dolby D +/Dolby TrueHD: “Bitstream”
– DTS/DTS-HD: “Bitstream”
– BD-Video Secondary Audio: “Off”
Dolby Atmos is a trademark of Dolby Laboratories.
∫ OPTICAL / COAXIAL Down Sampling
Select whether or not to convert the sampling
frequency of the audio to be output from the
OPTICAL/COAXIAL terminal.
If you choose to convert the sampling frequency,
you can limit the maximum output to 48 kHz or
96 kHz.
≥ Set a frequency supported by the connected
device.
≥ When playing back BD-Video, signals are
converted to 48 kHz despite the settings in the
following cases:
– when the signals have a sampling frequency
of 192 kHz
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to
“On”
∫ Downmix
Select the downmix system of multi-channel to
2-channel sound.
≥ Select “Surround encoded”, when the
connected equipment supports the virtual
surround function.
≥ The downmix effect is not available when
“Digital Audio Output” is set to “Bitstream”.
≥ The audio will be output in “Stereo” in the
following cases:
– AVCHD playback
– Playback of secondary audio (including the
button click sound).
∫ HDMI Output Settings of Music Playback
Minimise the audio noise during music playback
by automatically switching the video output to
1080i.
∫ Settings for High Clarity Sound
Set a terminal that will stop processing audio
signals or whether or not to turn on/off the unit’s
display when “High Clarity Sound” (> 28) is set to
“On (Video Off)” or “On (Video On)”.
≥ Set an option for video playback and audio
playback.
∫ Audio Delay
Synchronization between picture and sound is
corrected by adjusting the delay time of the audio
output.
∫ Analog Multi Channel
Multi-channel surround sound is output from the
AUDIO OUT terminals.
≥ If “On” is selected, audio will not be output from
the HDMI OUT terminal.
– Speaker presence and size
(
– Delay time (
)
)
– Channel balance (
)
To finish the speaker setting
Select “Complete”.
∫ Voice Guidance Setting
Voice Guidance reads aloud various on-screen
information, such as menu items, explanatory
text, and currently-selected items. (It is also
possible to display the “Voice Guidance Setting”
screen by pressing and holding the [HOME]
button for at least 5 seconds while the HOME
menu is displayed.)
≥ Information is read aloud in PCM audio format.
≥ Audio with sampling frequencies above 48 kHz
are down-sampled to 48 kHz or lower.
≥ When “On” is set, this unit operates in the
manner described below.
– “Dolby D/Dolby D +/Dolby TrueHD” and
“DTS/DTS-HD” in “Digital Audio Output” are
fixed to “PCM”. (> 30)
– “Re-master” in “Sound Effects” is disabled.
(> 28)
– Even when “Sound Effects” is set to “Digital
Tube Sound”, the maximum upsampling
frequency will be fixed at 48 kHz. (> 28)
– Audio is muted during searching ([6] or
[5]).
TQBA2018
31
Reference
DMP-UB900_P-TQBA2018.book 31 ページ
DMP-UB900_P-TQBA2018.book 32 ページ
2016年11月23日 水曜日 午後12時29分
3D
∫ 3D BD-Video Playback
Select the playback method of 3D compatible
video software.
∫ 3D AVCHD Output
Select the output method of 3D AVCHD videos.
∫ 3D Playback Precautions
Set to display or hide the 3D viewing warning screen
when playing back the 3D compatible video software.
Language
∫ Audio Language
Choose the language for audio.
≥ If “Original” is selected, the original language of
each disc will be selected.
≥ When the selected language is not recorded on
the disc, or depending on how the navigation is
created on the disc, it may playback in a
different language than the selected language.
≥ Enter a code (> 42) when you select “Other
¢¢¢¢”.
∫ Subtitle Language
Choose the language for the subtitle.
≥ When “Auto” is selected, a subtitle for the
language selected in the “Audio Language” is
displayed only when the language other than
the language selected in the “Audio Language”
is played back.
≥ When the selected language is not recorded on
the disc, or depending on how the navigation is
created on the disc, it may playback in a
different language than the selected language.
≥ Enter a code (> 42) when you select “Other
¢¢¢¢”.
∫ Menu Language
Choose the language for the disc menus.
≥ Enter a code (> 42) when you select “Other
¢¢¢¢”.
∫ Subtitle Text
Select a desired item according to the language
used for MKV subtitles text.
≥ This item is displayed only after playing back a file.
∫ On-screen Language
Choose the language for menus and on-screen
messages.
32
TQBA2018
∫ Closed Caption
Closed captioning services are dependent on
contents, and the unit can display closed captions
of both digital and analog types.
Press [OK] to show the following settings:
¾Closed Caption Display
Set whether or not to display closed captions.
¾Closed Caption Type
Select the closed caption type that matches the
one of the content to be played back.
¾Analog CC
Select the channel of analog closed captions.
¾Digital CC
Select the channel of digital closed captions.
¾Manual setting
Set the display style of closed captions.
¾CC Reset
Restore the default “Closed Caption” settings.
Network
∫ Easy Network Setting (> 17)
∫ Network Settings
Perform network-related settings individually.
Press [OK] to show the following settings:
¾LAN Connection Mode
Select the LAN connection method.
≥ When not using wireless LAN (when turning it
off), select “Wired”.
¾Wireless Settings
This allows the wireless router and connection
settings to be set up. Current connection
settings and connection state can be checked.
The wireless router connection wizard will be
displayed.
Select a connection method to wireless access
point.
Search for wireless network
WPS (PUSH button method)
WPS (PIN code method)
Manual setting
2016年11月23日 水曜日 午後12時29分
¾IP Address/DNS Settings
This is for checking the state of the network
connection and setting the IP address and
DNS-related.
Press [OK] to show the respective setting.
¾Proxy Server Settings
This is for checking the state of connection with
the Proxy server and performing settings.
Press [OK] to show the respective setting.
¾Remote Device Settings (> 24)
Press [OK] to show the following settings:
Remote Device Operation
Enable to operate the unit by DMC.
Setting Unit Name
Set the name of this unit to be displayed on
the connected equipment.
Registration Type
¾Network Service Settings (> 22)
Press [OK] to show the following settings:
Second Screen Browsing
When this function is set to “On”, you can
enjoy the content you are viewing on a
network service application of smartphone,
etc. with the home network on the big screen
of your TV.
Audio Auto Gain Control
Volume that is different depending on the
contents is adjusted automatically to the
standard volume while using the Network
Service.
≥ Depending on contents, this function effect
will not work.
≥ Select “Off” when the audio is distorted.
Time Zone
Set the unit’s time to match your location.
≥ Some Network Service contents require the
time zone to be set. Set time zone if
necessary.
DST
Select “On” when using Daylight Saving time.
Notice
Displays the terms of service for the cloud
services.
¾Network Drive Connection
This unit can access a hard disk shared folder
on a network and play back videos, still
pictures, and music.
Auto
Allow connections to all
the equipment accessing
this unit.
Manual
Set the permission for
individual equipment
connections accessing this
unit.
Remote Device List
Registering/deregistering of the displayed
equipment can be performed when “Manual”
in “Registration Type” is selected.
¾BD-Live Internet Access (> 21)
You can restrict Internet access when BD-Live
functions are used.
≥ If “Allow ( Limited )” is selected, Internet
access is permitted only for BD-Live contents
which have content owner certificates.
Ratings
The following items use the same password.
Don’t forget your password.
∫ DVD-Video Ratings
Set a ratings level to limit DVD-Video play.
∫ BD-Video Ratings
Set an age limit of BD-Video (including Ultra HD
Blu-ray) play.
∫ Network Service Lock
You can restrict the usage of Network Service.
TQBA2018
33
Reference
DMP-UB900_P-TQBA2018.book 33 ページ
DMP-UB900_P-TQBA2018.book 34 ページ
2016年11月23日 水曜日 午後12時29分
System
∫ Easy Setting
You can execute basic settings.
∫ Display Settings
Press [OK] to show the following settings:
¾Screen Saver Function
This is to prevent image retention on the
screen.
≥ When this is set to “On”:
If a list of playback content is displayed and
there is no operation for 5 minutes or more,
the screen switches to HOME menu
automatically.
≥ While playing and pausing, etc., this function
is not available.
¾Status Messages
Choose whether to show status messages
automatically.
¾VIERA Link
Set to use “VIERA Link” function when
connected via HDMI cable to a device that
supports “VIERA Link”.
≥ Select “Off” when you do not want to use
“VIERA Link”.
∫ Front Panel Display
Changes the brightness of the unit’s display.
This setting is also able to switch by pressing
[DIM].
≥ If “Auto” is selected, the display is set to bright
and only dimmed during playback.
≥ This setting does not work when “Front Panel
Display” in “Settings for High Clarity Sound” is
set to “Off”. (> 31)
(Except for when “High Clarity Sound” is set to
“Off”)
34
TQBA2018
∫ Quick Start
Speed of start-up from standby mode is
increased.
≥ When set to “On”, the internal control unit will be
powered. The idle power consumption will
increase so compared to when set to “Off”.
∫ Remote Control Code
Change the remote control code if other
Panasonic products react to this remote control.
∫ Firmware Update (> 18)
Press [OK] to show the following settings:
¾Automatic Update Check
When this equipment remains connected to the
Internet, it will check for the latest firmware
version when it is turned on and you can update
it if necessary.
¾Update Now
You can update the firmware manually if a
firmware update is available.
∫ System Information
Press [OK] to show the following settings:
¾License
Information about the software used by this unit
is displayed.
¾Firmware Version Information
Display firmware version of this unit and
wireless LAN module.
∫ Restore Default Settings
This returns all values in the Setup menu and the
Option menu to the default settings, except for
some settings of network, ratings, remote control
code, on-screen language, etc.
2016年11月23日 水曜日 午後12時29分
Troubleshooting guide
Before requesting service, please perform the
following checks.
Do you have the latest firmware installed?
Panasonic is constantly improving the unit’s
firmware to ensure that our customers are
enjoying the latest technology. (> 18)
4
Make the following checks and visit our
website for more information.
http://shop.panasonic.com/support
Enter the model number.
4
Or visit our website to find a service center.
You can find a service center near you easily
on our website.
Other support information:
“Limited Warranty” (> 45).
General operation
To return to the factory default.
¾ Select “Yes” in “Restore Default Settings” in
the Setup menu. (> 34)
To return all settings to the factory preset.
¾ Reset the unit as follows:
1 While the unit is off
Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [1] (right) repeatedly on the remote
control until “08 FIN” is displayed on the unit’s
display.
3 Press and hold [OK] for more than 5 seconds.
* Perform this operation when the light on the remote control
button is turned off. (> 8, [LIGHT])
The following do not indicate a problem with
this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
This unit is turned off when the input for the
TV is switched.
¾ This is a normal phenomenon when using
VIERA Link. For details please read the
owner’s manuals for the TV.
∫ Unit does not respond to remote
control or unit’s buttons.
The remote control doesn’t work properly.
¾ Change the batteries in the remote control.
(> 5)
¾ The remote control and this unit are using
different codes.
If “SET CODE ” is displayed on the unit’s
display when a button is pressed on the
remote control, change the code on the
remote control.
Press and hold [OK] and the displayed
number (“”) for more than 5 seconds.
Touch and hold [Í/I] on the main unit for
3 seconds.
– If still unable to turn the unit off, disconnect the
AC power supply cord, wait 1 minute, then
reconnect the AC power supply cord.
∫ The buttons of the unit do not
work.
Touch the buttons with your finger. They may not
work if operated with your fingernails or hands
wearing gloves.
∫ The buttons of the unit are
sensitive.
The buttons of the unit respond to light touch. Do
not place objects on or around them.
∫ Cannot eject disc.
This unit is turned off automatically.
¾ To save on electricity, this unit is turned off
automatically depending on the media if there
is no button operation for about 20 minutes
when not playing back (such as when paused
or displaying the menu, displaying still
pictures, etc.).
1 While the unit is off
Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [1] (right) repeatedly on the remote
control until “06 FTO” is displayed on the
unit’s display.
3 Press [OK].
* Perform this operation when the light on the remote control
button is turned off. (> 8, [LIGHT])
TQBA2018
35
Reference
DMP-UB900_P-TQBA2018.book 35 ページ
DMP-UB900_P-TQBA2018.book 36 ページ
2016年11月23日 水曜日 午後12時29分
You have forgotten your ratings password.
You want to cancel the ratings level.
¾ The ratings level returns to the factory
defaults.
1 While the unit is on
Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [1] (right) repeatedly on the remote
control until “03 VL” is displayed on the unit’s
display.
3 Press [OK].
* Perform this operation when the light on the remote control
button is turned off. (> 8, [LIGHT])
The TV screen turns black.
¾ In the following cases, HDMI authentication
takes place and a black screen is displayed:
– When “24p Conversion” is set to “On”.
– When “24p Output” is set to “Auto”.
– When the display is switched between 2D
and 3D images.
– When you quit the 4K playback by
displaying another screen, including the
HOME menu.
– When “HDMI Output Settings of Music
Playback” is set to “Sound Quality Priority”.
This unit does not recognize the USB
connection correctly.
¾ Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
¾ USB devices may not be recognized by this
unit when connected using the following :
– a USB hub
– a USB extension cable
¾ If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
¾ If the USB HDD is not recognized, the power
to the USB HDD may not be supplied. Supply
power from an external source.
Picture
Images from this unit do not appear on the TV
screen, or they are distorted.
¾ An incorrect resolution is selected in
“Resolution”. Reset the setting as follows:
1 While the unit is on
Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [1] (right) repeatedly on the remote
control until “04 PRG” is displayed on the
unit’s display.
3 Press and hold [OK] for more than 5 seconds.
Set the item again. (> 29)
– When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD® audio are not output properly,
select “Yes” in “Restore Default Settings”
(> 34) and make proper settings.
¾ The connected devices are changed. Reset
the setting as follows:
1 While the unit is on
Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.*
– “00 RET” is displayed on the unit’s display.
2 Press [1] (right) repeatedly on the remote
control until “13 L4K” is displayed on the unit’s
display.
3 Press and hold [OK] for more than 5 seconds.
– “4K60p Output” will be set to “Off”. Make
the correct setting again. (> 29)
* Perform this operation when the light on the remote control
button is turned off. (> 8, [LIGHT])
¾ When “3D BD-Video Playback” in the Setup
menu is set to “Auto”, images may not be
output depending on the connection method.
After removing the disc from this unit, select
“Set before play” in the Setup menu, and
select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 32)
¾ When outputting in 4K, images may be
distorted depending on the HDMI cable. Use
an HDMI cable that supports 18 Gbps.
36
TQBA2018
2016年11月23日 水曜日 午後12時29分
Video is not output.
¾ Video is not output when the “High Clarity
Sound” is set to “On (Video Off)”. (> 28)
¾ Video from the HDMI AUDIO OUT terminal is
not output when the “HDMI(AUDIO) Output
Mode” is set to “Audio Only”. (> 29)
Video is not output in 4K or high-definition.
¾ Confirm that “Resolution” in the Setup menu
is set properly. (> 29)
¾ Confirm the HDMI cable, related connections
and the compatibility of TV video input.
To output images in 4K, connect the HDMI
cable to a 4K compatible terminal of the
connected device. (> 10)
¾ Set “HDMI(AUDIO) Output Mode” to “Audio
Only”. (> 29)
¾ To enjoy image in 4K/60p, set “4K60p Output”
to “4K/60p(4:4:4)” or “4K/60p(4:2:0)”. (> 29)
¾ If “4K60p Output” is set to “4K/60p(4:4:4)”,
check to see if the connected HDMI cable
supports 18 Gbps. (> 10, 29)
¾ If 4K images are not output from the
connected 4K-compatible TV, set “4K60p
Output” to “4K/60p(4:4:4)” or “4K/60p(4:2:0)”.
(> 29)
3D video is not output.
¾ Connect to a 3D compatible device (e.g., TV
and amplifier/receiver).
¾ When a non-3D compatible amplifier/receiver
is connected between this unit and a TV, 3D
video is not output. (> 13)
¾ If there is a non-3D compatible amplifier/
receiver connected to the HDMI AUDIO OUT
terminal, set the “HDMI(AUDIO) Output
Mode” to “Audio Only”. (> 29)
¾ Confirm the settings on this unit and the TV
for 3D. (> 21)
3D video is not output correctly as 2D.
¾ Select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 32, “3D
BD-Video Playback”)
¾ Discs that have recorded titles with Side by
side (2 screen structure) and that can be
enjoyed in 3D are played back in accordance
with the settings of the TV.
The subtitles overlap closed captions
recorded on discs.
¾ Turn off the subtitles or the closed captions.
(> 26, 27, 32)
Closed captions are not displayed.
¾ Confirm that the source content supports CC.
¾ Confirm the “Closed Caption Display” is set to
“On”. (> 27, 32)
¾ Change the “Closed Caption Type” setting.
(> 27, 32)
¾ Confirm the “Analog CC” or “Digital CC” is set
properly (> 27, 32).
A black band is displayed around the edge of
the screen.
The aspect ratio of the screen is abnormal.
¾ Adjust the aspect setting on the TV.
There is a lot of image lag when playing video.
¾ Set “0” all items in the “Noise Reduction”.
(> 27)
¾ Set “Audio Delay”. (> 31)
Audio
Cannot hear the desired audio.
¾ Check the connections and the “Digital Audio
Output” settings. (> 11, 30)
¾ When the unit is connected to an amplifier/
receiver with the 7.1ch AUDIO OUT
terminals, set “Analog Multi Channel”. (> 31)
¾ To output audio from a device connected with
an HDMI cable, set “Audio Output” to “On” in
the Setup menu. (> 30)
¾ When connecting this unit to a TV via an
HDMI VIDEO OUT and to an amplifier/
receiver via an HDMI AUDIO OUT, set
“HDMI(VIDEO) Output Mode” to “Auto ( Video
Only / Video+Audio )”. (> 11, 29)
No subtitles.
¾ When progressive output is on, closed
captions/subtitles cannot be displayed.
TQBA2018
37
Reference
DMP-UB900_P-TQBA2018.book 37 ページ
DMP-UB900_P-TQBA2018.book 38 ページ
2016年11月23日 水曜日 午後12時29分
There is no sound coming out.
¾ To output audio using DIGITAL AUDIO OUT
terminal, set “OPTICAL / COAXIAL Down
Sampling” properly. (> 31)
¾ Refer to “Connecting to an amplifier/receiver”
(> 11 - 15) to check the audio output settings
suited to the connections of your device.
In the following cases, audio is not output
from the terminals listed below:
≥ HDMI VIDEO OUT terminal
– When a device is connected to the HDMI
AUDIO OUT terminal and “HDMI(VIDEO)
Output Mode” is set to “Auto ( Video Only /
Video+Audio )” (> 29)
– When “Audio Output” in “Advanced
Settings” is set to “Off” (> 30)
– While playback is being performed with
“Audio Output” in “Settings for High Clarity
Sound” set to “OPTICAL / COAXIAL Only”
or “Analog Only” (> 31)
– When “Analog Multi Channel” is set to “On”
(> 31)
≥ HDMI AUDIO OUT terminal
– When “Audio Output” in “Advanced
Settings” is set to “Off” (> 30)
– While playback is being performed with
“Audio Output” in “Settings for High Clarity
Sound” set to “OPTICAL / COAXIAL Only”
or “Analog Only” (> 31)
– When “Analog Multi Channel” is set to “On”
(> 31)
≥ OPTICAL/COAXIAL terminal
– When a device is connected to the HDMI
AUDIO OUT terminal and “Audio Output” in
“Advanced Settings” is set to “On” (> 30)
– While playback is being performed with
“Audio Output” in “Settings for High Clarity
Sound” set to “HDMI Only” or “Analog Only”
(> 31)
≥ 2ch AUDIO OUT terminals
– When a device is connected to the HDMI
AUDIO OUT terminal and “Audio Output” in
“Advanced Settings” is set to “On” (> 30)
– While playback is being performed with
“Audio Output” in “Settings for High Clarity
Sound” set to “HDMI Only” or “OPTICAL /
COAXIAL Only” (> 31)
38
TQBA2018
≥ 7.1ch AUDIO OUT terminals
– While playback is being performed with
“Audio Output” in “Settings for High Clarity
Sound” set to “OPTICAL / COAXIAL Only”
(> 31)
– When “Analog Multi Channel” is set to “Off”
(> 31)
Playback
Disc cannot be played.
¾ The disc is dirty. (> 5)
¾ The disc is not finalized. (> 7)
¾ Depending on the Ultra HD Blu-ray disc, it
may not be possible to perform playback
unless this unit is connected to the Internet.
Still pictures (JPEG) do not play back
normally.
¾ The images that were edited on the PC, such
as Progressive JPEG, etc., may not be played
back.
I can’t play back BD-Live.
¾ The SD card is write-protected. (> 7)
¾ Confirm that this unit is connected to the
broadband Internet. (> 16)
¾ Confirm the “BD-Live Internet Access”
settings. (> 33)
¾ Confirm an SD card is inserted into the SD
card slot. (> 9)
Network
I can’t connect to the network.
¾ Confirm the network connection and settings.
(> 16, 17, 32)
¾ There may be interference that prevents the
unit from detecting your home network. Place
the unit and the wireless router closer to each
other. This unit may be able to detect your
network name (> 18, “SSID”).
¾ Check the owner’s manuals for each device
and connect accordingly.
2016年11月23日 水曜日 午後12時29分
When using wireless LAN connection, video
from the DLNA Certified media server is not
played back or video frames are dropped
during playback.
¾ Higher transfer rate router such as 802.11ac or
11n (2.4 GHz or 5 GHz) wireless router may
solve the problem. If you use 802.11ac or 11n
(2.4 GHz or 5 GHz) wireless router, it is
necessary to set the encryption type to “AES”.
Simultaneous use with a microwave, cordless
telephone etc. at 2.4 GHz may result in
connection interruptions or other problems.
¾ On the “Wireless Settings” screen (> 32), the
continuous lighting of at least 4 “Reception”
indicators is the target for a stable connection.
If 3 or fewer indicators are lit or the
connection is being interrupted, change the
position or angle of your wireless router and
see if the connection state improves. If there
is no improvement, connect to a wired
network and perform the “Easy Network
Setting” (> 17) again.
Messages on the screen
Cannot read. Please check the disc.
¾ You inserted an incompatible disc. (Video CD,
etc.)
Cannot play.
¾ You inserted an incompatible disc (Discs
recorded in PAL video, etc.).
Cannot play this title.
¾ You tried to play a non-compatible video.
No disc inserted.
¾ The disc may be upside down.
$ This operation is not available.
¾ Some operations are unsupported by the unit.
(For example, reverse slow motion, etc.)
IP address is not set.
¾ The “IP Address” in “IP Address/DNS
Settings” is “---. ---. ---. ---”. Set the “IP
Address”, “Subnet Mask”, and “Default
Gateway”. (Select the automatic address
acquisition if necessary.)
The current wireless network security setting
is weak. It is recommended to change to a
stronger security setting.
¾ Set a stronger network security level referring
to the wireless router owner’s manuals.
Messages on the unit’s
display
F99
¾ The unit fails to operate properly. Touch [Í/I]
on the main unit for 3 seconds to switch the
unit to standby, then switch back on.
NET
¾ While connecting to a network.
NO PLAY
¾ There is a viewing restriction on a BD-Video
or DVD-Video. (> 33)
¾ A DVD-Video disc with an incompatible color
encoding system or region code is inserted.
NO READ
¾ The media is dirty or badly scratched. The
unit cannot play.
REMOVE
¾ The USB device is drawing too much power.
Remove the USB device.
SET CODE 
(“ ” stands for a number.)
¾ The remote control and this unit are using
different codes. Change the code on the
remote control.
Press and hold
[OK] and the
indicated number
button at the same time for more than
5 seconds.
U59
¾ Temperature of this unit is hot and the unit
switches to standby for safety reasons.
Wait for about 30 minutes.
Install or place this unit with good ventilation.
START
¾ A firmware update will start. Please do not
turn off the unit.
UPDATE /5
(“ ” stands for a number.)
¾ A firmware update is in progress.
Please do not turn off the unit.
FINISH
¾ The firmware update is complete.
TQBA2018
39
Reference
DMP-UB900_P-TQBA2018.book 39 ページ
DMP-UB900_P-TQBA2018.book 40 ページ
2016年11月23日 水曜日 午後12時29分
Specifications
General
File format
File format
Extension
Reference
“.MKV”, “.mkv”
Signal system
NTSC
Operating temperature
range
i5 oC to i35 oC
(i41 oF to i95 oF)
Operating humidity
range
10 % to 80 % RH
(no condensation)
AUDIO OUT (Pin jack)
Analog Audio output (L/R,
7.1ch):
Standard : 0.5 Vrms,
Full scale : 2.0 Vrms at 1 kHz
(<500 ≠)
Audio performance
Frequency response:
4 Hz to 88 kHz
S/N ratio:
115 dB (2ch L/R, FL/FR)
Dynamic range:
110 dB (2ch L/R, FL/FR)
DIGITAL AUDIO OUT
(OPTICAL/COAXIAL)
1 pc.
Output format : PCM, Dolby
Digital, DTS®
HDMI OUT
(19 pin type A)
2 pcs.
Output Audio format : PCM,
Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS®, DTS-HD
High Resolution AudioTM,
DTS-HD Master AudioTM
USB port (Type A)
1 pc.
SD card slot
1 pc.
LAN (Ethernet) Port
1 pc.
10BASE-T/100BASE-TX/
1000BASE-T
Wireless LAN
Standard Compliance:
IEEE802.11 a/b/g/n/ac
MKV
≥ The video file and
subtitles text file are
inside the same folder,
and the file names are
the same except for the
file extensions.
Subtitles text file ≥ Some MKV files may
not be played back
“.SRT”, “.srt”,
correctly, depending on
“.SSA”, “.ssa”,
the video resolution,
“.ASS”, “.ass”
frame rate condition,
subtitle format and so
on.
≥ MOTION JPEG is not
supported.
mp4
(Compression
“.MP4”, “.mp4”,
methods
“.MOV”, “.mov”
Video: H.264
Audio: AAC)
MPEG
(TS/PS)
≥ Resolution up to
3840×2160 30p,
4096×2160 24p. (MP4
only)
≥ Some mp4/MPEG files
may not be played
back correctly,
depending on the video
resolution, frame rate
condition and so on.
“.MPG”, “.mpg”,
≥ MOTION JPEG is not
“.MPEG”, “.mpeg”,
supported.
“.M2TS”, “.m2ts”, ≥ Depending on the
“.MTS”, “.mts”,
audio compression
“.TS”, “.ts”
method, only images
may be played back
and it may not be
possible to output
audio.
JPEG
“.JPG”, “.jpg”
≥ MOTION JPEG and
Progressive JPEG are
not supported.
≥ You may not be able to
play back the file if you
have edited the folder
structure or the file
name on a PC or other
device.
MPO
“.MPO”, “.mpo”
3D still picture
MP3
“.MP3”, “.mp3”
This unit supports ID3
tags, but only titles, artist
names and album names
can be displayed.
FLAC
“.FLAC”, “.flac”
This unit supports tags,
but only titles, artist
names and album names
can be displayed.
Maximum sampling rate:
192 kHz/24 bit
Frequency Range:
2.4 GHz/5 GHz band
Security:
WPATM/WPA2TM (Encryption
type: TKIP/AES, Authentication
type: PSK), WEP (64 bit/128 bit)
LASER Specification
Class I LASER Product
Wave length: 777-800 nm (CDs)/
650-665 nm (DVDs)/
400-410 nm (BDs)
Laser power: No hazardous radiation
is emitted with the safety protection
(
) 120 V, 60 Hz
Power supply
AC
Power consumption
Approx. 25 W
WAV
“.WAV”, “.wav”
Power consumption in
standby mode
Approx. 0.2 W
(Quick Start: Off)
Maximum sampling rate:
192 kHz/32 bit
AAC
“.M4A”, “.m4a”
Maximum sampling rate:
48 kHz/320 kbps
Power consumption in
Approx. 8 W
quick start standby mode (Quick Start: On)
Dimensions (WkHkD)
435 mmk68 mmk207 mm
Including the projecting (Approx.
parts
17 3/16zk2 11/16zk8 3/16z)
Mass (Weight)
Approx. 2.4 kg (5.3 lbs)
≥ Specifications are subject to change without notice.
40
TQBA2018
DMP-UB900_P-TQBA2018.book 41 ページ
WMA
Extension
Reference
This unit supports tags,
but only titles, artist
names and album names
can be displayed.
Maximum sampling rate:
48 kHz/385 kbps
“.WMA”, “.wma”
DSD
“.DSF”, “.dsf”,
(DFF, DSF) “.DFF”, “.dff”
ALAC
2.8 MHz (2 ch/5.1 ch),
5.6 MHz (2 ch only)
96 kHz/32 bit (Max.7.1 ch),
176.4/192 kHz/32 bit
(Max.5.1 ch)
“.M4A”, “.m4a”
≥ With certain recording states and folder structures, the play
order may differ or playback may not be possible.
≥ A combined total of up to 10,000 files and folders can be
displayed as playable data in each folder regardless of
their format.
(Even when the picture playback menu is displayed, for
example, if a folder in the menu contains playable videos
and music files, they are also counted as playable data.)
Audio information
≥ The number of channels listed is the maximum possible
number of output channels when connected to amplifier/
receiver compatible with the respective audio format.
HDMI OUT/
COAXIAL/OPTICAL (DIGITAL AUDIO OUT)
Output
channel
When this unit works as a DLNA client, following
contents are playable.
≥ File formats that are not supported by your
DLNA server cannot be played.
Video
Container
Video codec Audio codec
MKV
H.264
AVCHD
MP4
H.264
PS
MPEG2
TS
MPEG2
H.264
Example of
file extension
AAC
PCM
.mkv
Vorbis
FLAC
Dolby Digital
.mts
AAC
.mp4, .mov
Dolby Digital
.mpg, .mpeg
Linear PCM
AAC
.m2ts, .ts
Dolby Digital
Photo
The audio output differs depending on which
terminals are connected to the amplifier/receiver,
and the settings on the unit. (> 30, “Digital Audio
Output”)
Terminal
Supported format for DLNA
“Digital Audio Output”
“Bitstream”
“PCM”
HDMI OUT
Outputs using
original audio*1
BD-Video :
7.1ch PCM*1*2
DVD-Video :
5.1ch PCM
COAXIAL/
OPTICAL
(DIGITAL
AUDIO
OUT)
Dolby Digital/
DTS Digital
SurroundTM
Down-mixed
2ch PCM
Format
JPEG
Example of file extension
.jpg
Audio
Audio codec
MP3
FLAC
WAV
AAC
WMA
ALAC
DSD
Linear PCM
Example of file extension
.mp3
.flac
.wav
.m4a, .adts
.wma
.m4a
.dsf, .dff
—
Reference
File format
2016年11月23日 水曜日 午後12時29分
≥ Depending on the server, the contents other than stated
above can be played back.
Analog AUDIO OUT
Output
channel
*1
*2
2ch AUDIO OUT
2ch
BD-Video : 7.1ch*1*2
7.1ch AUDIO OUT
DVD-Video : 5.1ch
When “BD-Video Secondary Audio” is set to “On”, the
audio will be output as Dolby Digital, DTS Digital
SurroundTM or 5.1ch PCM.
The audio output is amplified from 5.1ch or 6.1ch to 7.1ch
depending on the DTS, Inc. specifications.
TQBA2018
41
DMP-UB900_P-TQBA2018.book 42 ページ
2016年11月23日 水曜日 午後12時29分
Language code list
Language
Code Language
Abkhazian:
6566
Afar:
6565
Afrikaans:
6570
Albanian:
8381
Amharic:
6577
Arabic:
6582
Armenian:
7289
Assamese:
6583
Aymara:
6589
Azerbaijani: 6590
Bashkir:
6665
Basque:
6985
Bengali; Bangla:
6678
Bhutani:
6890
Bihari:
6672
Breton:
6682
Bulgarian:
6671
Burmese:
7789
Byelorussian: 6669
Cambodian: 7577
Catalan:
6765
Chinese:
9072
Corsican:
6779
Croatian:
7282
Czech:
6783
Danish:
6865
Dutch:
7876
English:
6978
Esperanto:
6979
Estonian:
6984
Faroese:
7079
Fiji:
7074
Finnish:
7073
French:
7082
Frisian:
7089
Galician:
7176
Georgian:
7565
German:
6869
Greek:
6976
Greenlandic: 7576
Guarani:
7178
42
TQBA2018
Display languages list
Code Language
Gujarati:
7185
Hausa:
7265
Hebrew:
7387
Hindi:
7273
Hungarian:
7285
Icelandic:
7383
Indonesian: 7378
Interlingua:
7365
Irish:
7165
Italian:
7384
Japanese:
7465
Javanese:
7487
Kannada:
7578
Kashmiri:
7583
Kazakh:
7575
Kirghiz:
7589
Korean:
7579
Kurdish:
7585
Laotian:
7679
Latin:
7665
Latvian, Lettish: 7686
Lingala:
7678
Lithuanian:
7684
Macedonian: 7775
Malagasy:
7771
Malay:
7783
Malayalam: 7776
Maltese:
7784
Maori:
7773
Marathi:
7782
Moldavian:
7779
Mongolian:
7778
Nauru:
7865
Nepali:
7869
Norwegian: 7879
Oriya:
7982
Pashto, Pushto: 8083
Persian:
7065
Polish:
8076
Portuguese: 8084
Punjabi:
8065
Quechua:
8185
Code
Rhaeto-Romance:
8277
Romanian:
8279
Russian:
8285
Samoan:
8377
Sanskrit:
8365
Scots Gaelic: 7168
Serbian:
8382
Serbo-Croatian: 8372
Shona:
8378
Sindhi:
8368
Singhalese: 8373
Slovak:
8375
Slovenian:
8376
Somali:
8379
Spanish:
6983
Sundanese: 8385
Swahili:
8387
Swedish:
8386
Tagalog:
8476
Tajik:
8471
Tamil:
8465
Tatar:
8484
Telugu:
8469
Thai:
8472
Tibetan:
6679
Tigrinya:
8473
Tonga:
8479
Turkish:
8482
Turkmen:
8475
Twi:
8487
Ukrainian:
8575
Urdu:
8582
Uzbek:
8590
Vietnamese: 8673
Volapük:
8679
Welsh:
6789
Wolof:
8779
Xhosa:
8872
Yiddish:
7473
Yoruba:
8979
Zulu:
9085
Display Language Display Language Display Language
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS
English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian
JPN
CHI
KOR
MAL
VIE
THA
POL
CES
SLK
HUN
FIN
Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Polish
Czech
Slovak
Hungarian
Finnish
TV code list
Brand
TV Code
Panasonic
01/02
LG
10/11
SAMSUNG
20/21/22
SONY
30
VIZIO
40/41
ARA
HIN
PER
IND
MRI
BUL
RUM
GRE
TUR
Arabic
Hindi
Persian
Indonesian
Maori
Bulgarian
Romanian
Greek
Turkish
Others
2016年11月23日 水曜日 午後12時29分
Licenses
“AVCHD”, “AVCHD 3D”, “AVCHD Progressive” and “AVCHD 3D/
Progressive” are trademarks of Panasonic Corporation and Sony
Corporation.
Java is a registered trademark of Oracle and/or its affiliates.
Dolby, Dolby Audio, and the double-D symbol are trademarks of
Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, &
DTS and the Symbol together are registered trademarks, and
DTS-HD Master Audio | Essential is a trademark of DTS, Inc.
© DTS, Inc. All Rights Reserved.
THX and the THX logo are trademarks of THX Ltd., registered in
the United States and other jurisdictions.
All rights reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing, LLC in the United States and other countries.
<AVC>
This product is licensed under the AVC Patent Portfolio License for
the personal use of a consumer or other uses in which it does not
receive remuneration to (i) encode video in compliance with the
AVC Standard ("AVC Video") and/or (ii) decode AVC Video that
was encoded by a consumer engaged in a personal activity and/or
was obtained from a video provider licensed to provide AVC
Video. No license is granted or shall be implied for any other use.
Additional information may be obtained from MPEG LA, L.L.C.
See http://www.mpegla.com
<VC-1>
This product is licensed under the VC-1 Patent Portfolio License
for the personal and non-commercial use of a consumer to (i)
encode video in compliance with the VC-1 Standard ("VC-1
Video") and/or (ii) decode VC-1 Video that was encoded by a
consumer engaged in a personal and non-commercial activity
and/or was obtained from a video provider licensed to provide
VC-1 Video. No license is granted or shall be implied for any other
use. Additional information may be obtained from MPEG LA,
L.L.C.
See http://www.mpegla.com
Copyright 2004-2014 Verance Corporation. CinaviaTM is a Verance
Corporation trademark. Protected by U.S. Patent 7,369,677 and
worldwide patents issued and pending under license from Verance
Corporation. All rights reserved.
This product incorporates the following software:
(1) the software developed independently by or for Panasonic
Corporation,
(2) the software owned by third party and licensed to Panasonic
Corporation,
(3) the software licensed under the GNU General Public License,
Version 2.0 (GPL V2.0),
(4) the software licensed under the GNU LESSER General Public
License, Version 2.1 (LGPL V2.1), and/or
(5) open source software other than the software licensed under
the GPL V2.0 and/or LGPL V2.1.
The software categorized as (3) - (5) are distributed in the hope
that it will be useful, but WITHOUT ANY WARRANTY, without
even the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE.
Please refer to the detailed terms and conditions thereof shown in
the Player Settings menu.
At least three (3) years from delivery of this product, Panasonic
will give to any third party who contacts us at the contact
information provided below, for a charge no more than our cost of
physically performing source code distribution, a complete
machine-readable copy of the corresponding source code covered
under GPL V2.0, LGPL V2.1 or the other licenses with the
obligation to do so, as well as the respective copyright notice
thereof.
Contact Information: oss-cd-request@gg.jp.panasonic.com
The source code and the copyright notice are also available for
free in our website below.
http://panasonic.net/avc/oss/
Reference
DMP-UB900_P-TQBA2018.book 43 ページ
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
SDXC Logo is a trademark of SD-3C, LLC.
“DVD Logo” is a trademark of DVD Format/Logo Licensing
Corporation.
The Wi-Fi CERTIFIEDTM Logo is a certification mark of Wi-Fi
Alliance®.
The Wi-Fi Protected SetupTM Identifier mark is a certification mark
of Wi-Fi Alliance®.
“Wi-Fi®” and “Wi-Fi Direct®” are registered trademarks of Wi-Fi
Alliance®.
“Wi-Fi Protected SetupTM”, “MiracastTM”, “WPATM”, and “WPA2TM”
are trademarks of Wi-Fi Alliance®.
DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks,
service marks, or certification marks of the Digital Living Network
Alliance.
Windows is a trademark or a registered trademark of Microsoft
Corporation in the United States and other countries.
Android is a trademark of Google Inc.
TQBA2018
43
DMP-UB900_P-TQBA2018.book 44 ページ
2016年11月23日 水曜日 午後12時29分
(1) MS/WMA
This product is protected by certain intellectual property rights
of Microsoft Corporation and third parties. Use or distribution of
such technology outside of this product is prohibited without a
license from Microsoft or an authorized Microsoft subsidiary
and third parties.
(2) MS/PlayReady/Final Product Labeling
This product contains technology subject to certain intellectual
property rights of Microsoft. Use or distribution of this
technology outside of this product is prohibited without the
appropriate license(s) from Microsoft.
(3) MS/PlayReady/End User Notices
Content owners use Microsoft PlayReady™ content access
technology to protect their intellectual property, including
copyrighted content. This device uses PlayReady technology
to access PlayReady-protected content and/or
WMDRM-protected content. If the device fails to properly
enforce restrictions on content usage, content owners may
require Microsoft to revoke the device’s ability to consume
PlayReady-protected content. Revocation should not affect
unprotected content or content protected by other content
access technologies. Content owners may require you to
upgrade PlayReady to access their content. If you decline an
upgrade, you will not be able to access content that requires
the upgrade.
(4) Vorbis, FLAC, WPA Supplicant
The software licenses are displayed when “License” in the
Setup menu is selected. (> 34)
44
TQBA2018
DMP-UB900_P-TQBA2018.book 45 ページ
2016年11月23日 水曜日 午後12時29分
Limited Warranty
Panasonic Products Limited Warranty
If your product does not work properly because of a defect in
materials or workmanship, Panasonic Corporation of North
America (referred to as “the warrantor”) will, for the length of the
period indicated on the chart below, which starts with the date of
original purchase (“warranty period”), at its option either (a) repair
your product with new or refurbished parts, (b) replace it with a
new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be
made by the warrantor.
Product or Part Name
Parts
Labor
Blu-ray Disc Player
1 Year
90 Days
All included Accessories
(Except Non-Rechargeable
Batteries)
90 Days
Not Applicable
Only Non-Rechargeable Batteries 10 Days
Not Applicable
During the “Labor” warranty period there will be no charge for
labor. During the “Parts” warranty period, there will be no charge
for parts. This Limited Warranty excludes both parts and labor for
non-rechargeable batteries, antennas, and cosmetic parts
(cabinet). This warranty only applies to products purchased and
serviced in the United States. This warranty is extended only to the
original purchaser of a new product which was not sold “as is”.
Mail-In Service--Online Repair Request
Online Repair Request
(As examples, this excludes damages for lost time, travel to and
from the servicer, loss of or damage to media or images, data or
other memory or recorded content. The items listed are not
exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied
warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state. If a problem with
this product develops during or after the warranty period, you may
contact your dealer or Service Center. If the problem is not
handled to your satisfaction, then write to:
Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy
Chesapeake, VA 23320
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
for all your Panasonic gear
To submit a new repair request and for quick repair status visit our
Web Site at http://shop.panasonic.com/support
When shipping the unit, carefully pack, include all supplied
accessories listed in the Owner’s Manual, and send it prepaid,
adequately insured and packed well in a carton box. When
shipping Lithium Ion batteries please visit our Web Site at
http://shop.panasonic.com/support as Panasonic is committed to
providing the most up to date information. Include a letter detailing
the complaint, a return address and provide a daytime phone
number where you can be reached. A valid registered receipt is
required under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD,
THE PURCHASER WILL BE REQUIRED TO FURNISH A
SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE
OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY
UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits and Exclusions
This warranty ONLY COVERS failures due to defects in materials
or workmanship, and DOES NOT COVER normal wear and tear or
cosmetic damage. The warranty ALSO DOES NOT COVER
damages which occurred in shipment, or failures which are caused
by products not supplied by the warrantor, or failures which result
from accidents, misuse, abuse, neglect, mishandling,
misapplication, alteration, faulty installation, set-up adjustments,
misadjustment of consumer controls, improper maintenance,
power line surge, lightning damage, modification, introduction of
sand, humidity or liquids, commercial use such as hotel, office,
restaurant, or other business or rental use of the product, or
service by anyone other than a Factory Service Center or other
Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS
LISTED UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY.
Go to
http://shop.panasonic.com/support
Get everything you need to get the most out of
your Panasonic products
Accessories & Parts for your Camera, Phone, A/V
products, TV, Computers & Networking, Personal
Care, Home Appliances, Headphones, Batteries,
Backup Chargers & more...
Customer Services Directory
For Product Information, Operating Assistance,
Parts, Owner’s Manuals, Dealer and Service info
go to http://shop.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
As of June 2016
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER
SERIAL NUMBER
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
TQBA2018
45
Reference
Limited Warranty Coverage (For USA Only)
DMP-UB900_P-TQBA2018.book 46 ページ
2016年11月23日 水曜日 午後12時29分
Referencia rápida en español
(Spanish Quick Reference)
Conexiones básicas
Conexión a un televisor
compatible con HDMI
Conecte el cable de
alimentación de CA por
último

Cable HDMI
HDMI IN
Cable de alimentación de CA
(incluido)
A una toma
de
corriente
doméstica
Conexión a un televisor
compatible con HDMI y a un
amplificador/receptor
compatible con HDMI
HDMI IN
(ARC)
Cable HDMI
HDMI IN
HDMI OUT
(ARC)
Amplificador/Receptor
46
TQBA2018
≥ Conéctelo cuando haya realizado el resto de conexiones.
≥ Inserte el cable de alimentación de CA principal hasta A,
justo un punto antes del orificio redondo.
Ahorro de energía
Esta unidad consume una pequeña cantidad de energía
aunque esté ajustada en el modo de espera (Accionamiento
rápido : Desactivado, aprox. 0,2 W). Para ahorrar energía
cuando no vaya a utilizar la unidad durante mucho tiempo,
desenchúfela de la toma de corriente.
DMP-UB900_P-TQBA2018.book 47 ページ
2016年11月23日 水曜日 午後12時29分
Reproducción básica
Preparación
Encienda el televisor y seleccione la entrada de
vídeo adecuada en el televisor.
1
Pulse [Í] para encender la unidad.
Después de conectar su nuevo reprodutor y
pulsar el botón de encendido, aparecerá la
pantalla de la configuración básica.
2
Inserte el medio.
Inicia la reproducción
Pulse [1].
Parada
Pulse [∫].
La posición de detención se memoriza.
Función de reanudación de la reproducción
Pulse [1] para reiniciar la reproducción desde
esta posición.
Reference
≥ El punto se anula si se extrae el medio.
≥ En los discos BD-Video incluidos los BD-J, la función
de reanudación de la reproducción no funciona.
Pausa
Pulse [;].
≥ Pulse [;] otra vez o [1] para reiniciar la reproducción.
Búsqueda/Cámara lenta
Búsqueda
Durante la reproducción, pulse [6] o [5].
≥ Ultra HD Blu-ray, MKV, MP4 y MPEG2: No se escucha
sonido. (Cuando “Ajuste de la Guía por voz” está
configurado como “Activado”, el audio no se escucha con
independencia del medio.)
Cámara lenta
Durante la pausa, pulse [6] o [5].
≥ Vídeo BD y AVCHD: [5] únicamente.
≥ MKV, MP4 y MPEG2: No es eficaz.
La velocidad aumenta hasta 5 pasos.
≥ Música y MP3, etc.: La velocidad está fija en un paso.
≥ Pulse [1] para recuperar la velocidad de reproducción
normal.
Salto
Durante la reproducción o la pausa, pulse
[:] o [9].
Salta hasta el título, capítulo o pista que desee
reproducir.
TQBA2018
47
DMP-UB900_P-TQBA2018.book 48 ページ
2016年11月23日 水曜日 午後12時29分
Index
A Audio
Changing audio . . . . . .20
Language . . . . . . . .32, 42
B BD-Live . . . . . . . . . . . . . .21
C Closed Caption . . . . .27, 32
D DLNA . . . . . . . . . . . . . . . .24
DMC . . . . . . . . . . . . . . . . .24
F File format. . . . . . . . . . . .40
Firmware update . . . . . . .18
L LAN . . . . . . . . . . . . . . . . .16
Language
Audio . . . . . . . . . . . . . .32
Menu . . . . . . . . . . . . . .32
On-screen. . . . . . . . . . .32
M
N
P
Q
R
Soundtrack . . . . . . . . . 26
Subtitle . . . . . . . . . 26, 32
Media Renderer . . . . . . 24
Miracast . . . . . . . . . . . . . 23
Network
Connection . . . . . . . . . 16
Setting . . . . . . . . . 17, 32
Network Service . . . . . . .22
Pop-up menu . . . . . . . . . .20
Quick Start . . . . . . . . . . 34
Repeat play . . . . . . . . . . 26
Restore Default
Settings . . . . . . . . . . . . . . .34
Resume play function . . .19
S Subtitle . . . . . . . . . . 26, 32
U Ultra HD Blu-ray . . . . . . 21
USB device. . . . . . . . . . . . . 7
V VIERA Link . . . . . . . . . . 25
W Wireless LAN . . . . . . . . 16
24p . . . . . . . . . . . . . . . 27, 29
4K . . . . . . . . . . . . . 17, 27, 29
USA Only: Disposal may be regulated in your community due to environmental considerations. For
disposal or recycling information, please visit Panasonic website:
http://www.panasonic.com/environmental/
or call 1-888-769-0149.
Either of these labels
is affixed to this unit.
(Inside of product)
Panasonic Corporation of North America
pr
Two Riverfront Plaza, Newark, NJ 07102-5490
http://www.panasonic.com
C Panasonic Corporation 2016
Printed in China
TQBA2018-1
F0616HA1116
Download PDF
Similar pages