Leviton
Switched Power Distribution Unit
-
SH081-x, EH081-x
SH082-x, EH082-x
SV161-x, EH161-x
SV162-x, EH162-x
Installation and Operations Manual
OR-69070-00-00-01 © 2005 Leviton All rights reserved.
Instructions
This symbol is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Dangerous Voltage
This symbol is intended to alert the user to the presence of un-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
Protective Grounding Terminal
This symbol indicates a terminal that must be connected to earth ground prior to making any other
connections to the equipment.
Life-Support Policy
As a general policy, Leviton does not recommend the use of any of its products in the following
situations:
• life-support applications where failure or malfunction of the Leviton product can be reasonably
expected to cause failure of the life-support device or to significantly affect its safety or
effectiveness.
• direct patient care.
Leviton will not knowingly sell its products for use in such applications unless it receives in writing
assurances satisfactory to Leviton that:
• the risks of injury or damage have been minimized,
• the customer assumes all such risks, and
• the liability of Leviton is adequately protected under the circumstances.
The term life-support device includes but is not limited to neonatal oxygen analyzers, nerve stimulators
(whether used for anesthesia, pain relief or other purposes), auto-transfusion devices, blood pumps,
defibrillators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis
systems, neonatal ventilator incubators, ventilators (for adults or infants), anesthesia ventilators, infusion
pumps, and any other devices designated as “critical” by the U.S. FDA.
Please Recycle
Shipping materials are recyclable. Please save them for later use, or dispose of them appropriately.
Table of Contents
CHAPTER 1: INTRODUCTION
4
Quick Start Guide.............................................................................................................................4
Technical Support ............................................................................................................................4
Equipment Overview........................................................................................................................5
CHAPTER 2: INSTALLATION
6
Standard Accessories........................................................................................................................6
Optional Accessories........................................................................................................................6
Additional Required Items ...............................................................................................................6
Safety Precautions ............................................................................................................................6
Installing the Power Input Retention Bracket...................................................................................7
Mounting ..........................................................................................................................................7
Attaching the Expansion Module .....................................................................................................8
Connecting to the Power Source ......................................................................................................8
Connecting Devices..........................................................................................................................8
Connecting the Sensors ....................................................................................................................8
Connecting to the Unit .....................................................................................................................8
CHAPTER 3: OPERATIONS
9
Interfaces ........................................................................................................................................10
HTML Interface .............................................................................................................................11
Command Line Interface................................................................................................................20
CHAPTER 4: ADVANCED OPERATIONS
41
SSL.................................................................................................................................................42
SSH ................................................................................................................................................43
SNMP.............................................................................................................................................44
CHAPTER 5: APPENDICES
Appendix A: Resetting to Factory Defaults ...................................................................................52
Appendix B: Uploading Firmware .................................................................................................52
Appendix C: Technical Specifications ...........................................................................................53
Appendix D: Warranty and Support...............................................................................................56
52
Chapter 1: Introduction
Quick Start Guide
The following instructions will help you quickly install and configure your Switched PDU for use in
your data center equipment cabinet. For detailed information on each step, go to the page number listed
to the right.
1.
2.
3.
4.
5.
6.
7.
Mount the Switched PDU...........................................................................................................7
Connect to the power source ......................................................................................................8
Connect the devices....................................................................................................................8
Connect the sensors....................................................................................................................8
Connect to the Switched PDU....................................................................................................8
Configure the Switched PDU ...................................................................................................10
•
Login as the predefined Administrator (admn/admn) .......................................................10
•
Configure the network settings .........................................................................................14
•
Create new administrative user account............................................................................16
•
Configure location and Switched PDU names..................................................................13
•
Configure sensor names....................................................................................................13
•
Configure new user account(s) .........................................................................................16
• Remove the predefined Administrator ..............................................................................16
Connect the Switched PDU to the network.
Technical Support
Leviton understands that there are often questions when installing and/or using a new product. Free
Technical Support is provided from 6:00 AM to 4:30 PM, Monday-Friday, Pacific Time.
Leviton Voice & Data Division
2222 – 222nd Street SE
Bothell, WA 98021 USA
4•
Introduction
Tel: (800) 722.2082
Fax: 425.483.5270
Web: www.levitonvoicedata.com
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Equipment Overview
1.
2.
3.
4.
The power inlet/cord(s) connects the PDU to the electrical power source.
The Input Current LED(s) displays the current load for each infeed or electrical phase per infeed.
Two RJ45 connectors for Serial (RS-232) and Ethernet connection.
Two mini RJ11 connectors for Temperature/Humidity sensors.
Each Branch Circuit / electrical phase is clearly labeled for easy identification.
A number is printed above each outlet. These numbers may be used in commands that require an outlet
name. See Outlet Naming and Grouping in Chapter 3: Operations for more information.
4
3
2
1
2
4
3
1
Figure 1. Power Distribution Unit Views
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Introduction
•5
Chapter 2: Installation
Before installing your Leviton Switched Power Distribution Unit (PDU), refer to the following lists to
ensure that you have all the items shipped with the unit as well as all other items required for proper
installation.
Standard Accessories
•
Mounting hardware
Vertical models - two removable flanges with four M4 screws and two mounting L-brackets with
nut plates, four sets of screws and washers and optional button mounts.
Horizontal models – two removable flanges with M4 screws.
RJ45 to RJ45 crossover cable
RJ45 to DB9F serial port adapter (for connection to standard DB9M DTE serial port)
Outlet retention clips (208-240V models)
•
•
•
Additional items for xxxxx -1D1 models:
•
•
Separate power input cord.
Power input retention bracket hardware.
Two removable T-brackets with two 40mm screws.
Please call Technical Support from 6:30 AM to 4:30 PM, Monday – Friday, Pacific Time, for
additional information: Tel: (800) 722.2082.
Optional Accessories
•
Temperature/Humidity sensors
Additional Required Items
•
•
Flathead and Phillip screwdrivers
Screws, washers and nuts to attach the PDU to your rack
Safety Precautions
This section contains important safety and regulatory information that should be reviewed before
installing and using the Leviton Switched Power Distribution Unit. For input and output current
ratings, see Power Ratings in Appendix C: Technical Specifications.
Only for installation and use in a
Service Access Location in
accordance with the following
installation and use instructions.
This equipment is designed to be
installed on a dedicated circuit.
Dedicated circuit must have circuit
breaker or fuse protection.
PDUs have been designed without a
master circuit breaker or fuse to
avoid becoming a single point of
failure. It is the customer’s
responsibility to provide adequate
protection for the dedicated power
circuit. Protection of capacity equal
to the current rating of the PDU must
be provided and must meet all
applicable codes and regulations. In
North American, protection must
have a 10,000A interrupt capacity.
Destiné à l'installation et l'utilisation
dans le cadre de Service Access
Location selon les instructions
d'installation et d'utilisation.
Cet équipement est conçu à être installé
sur un circuit spécialisé.
Le circuit spécialisé doit avoir un
disjoncteur ou une protection de
fusible. PDUs ont été conçus sans
disjoncteur général ni fusible pour éviter
que cela devient un seul endroit de
panne. C’est la responsabilité du client
de fournir une protection adéquate pour
le circuit-alimentation spécialisé.
Protection de capacité équivalant à la
puissance de l'équipement, et
respectant tous les codes et normes
applicables. Les disjoncteurs ou fusibles
destinés à l'installation en Amérique du
Nord doivent avoir une capacité
d'interruption de 10.000 A.
The plug on the power supply cord
shall be installed near the equipment
and shall be easily accessible.
Installation Orientation: xVxxx-xxx
units are design to be installed in
vertical orientation.
Always disconnect the power supply
cord before opening to avoid
electrical shock.
La prise sur le cordon d’alimentation
sera installée près de l’équipement et
sera facilement disponible.
Installation Orientation : Les unités
xVxxx-xxx sont conçues pour être
installées dans une orientation verticale.
Toujours déconnecter le cordon
d’alimentation avant d’ouvrir pour éviter
un choque électrique.
WARNING! High leakage current!
Earth connection is essential before
connecting supply!
ATTENTION ! Haut fuite très possible !
Une connection de masse est
essentielle avant de connecter
l’alimentation !
6•
Installation
Nur für Installation und Gebrauch an
Anschlusszugriffspunkten gemäß der
folgenden Installations- und
Gebrauchsanweisungen.
Diese Ausrüstung ist zur Installation in
einem festen Stromkreis vorgesehen.
Der feste Stromkreis muss mit einem
Schutzschalter oder einem
Sicherungsschutz versehen sein.
PDUs verfügt über keinen
Hauptschutzschalter bzw. über keine
Sicherung, damit kein einzelner
Fehlerpunkt entstehen kann. Der
Kunde ist dafür verantwortlich, den
Stromkreis sachgemäß zu schützen.
Der Kapazitätsschutz entspricht der
aktuellen Stromstärke der Geräte und
muss alle relevanten Codes und
Bestimmungen erfüllen. Für
Installation in Nordamerika müssen
Ausschalter bzw. Sicherung über
10.000 A Unterbrechungskapazität
verfügen.
Der Stecker des Netzkabels muss in
der Nähe der Ausrüstung installiert
werden und leicht zugänglich sein.
Installationsausrichtung: xVxxx-xxx
Einheiten sind zur vertikalen
Installation vorgesehen.
Ziehen Sie vor dem Öffnen immer das
Netzkabel heraus, um die Gefahr
eines elektrischen Schlags zu
vermeiden.
ACHTUNG! Hoher Ableitstrom! Ein
Erdungsanschluss ist vor dem
Einschalten der Stromzufuhr
erforderlich!
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Installing the Power Input Retention Bracket
For units with a total maximum output <30A, it may be
necessary to install the power input retention bracket prior to
mounting the unit within the rack.
To install the power input retention bracket:
1.
2.
Remove the two screws attaching the IEC 60320 C19 inlet
to the enclosure.
Assemble and attach the retention bracket to the enclosure
as shown.
Figure 2.1 Retention Bracket assembly
Mounting
Figure 2.2 Mounting
Horizontal/Rack
1.
2.
3.
Select the appropriate bracket mounting points for proper mounting depth within the rack.
Attach the brackets to these mounting points with two screws for each bracket.
Install the enclosure into your rack, using the slots in each bracket. The slots allow about ¼ inch
of horizontal adaptability to align with the mounting holes of your rack.
NOTE: A mounting bracket kit for 23” wide racks or cabinets is available. Contact your Leviton distributor for more
information.
Vertical
1.
2.
3.
Attach the removable flanges to the mount points on the rear of the enclosure using M4 screws.
Attach the mounting L-brackets to the flanges with the supplied screws, washers and nut plates.
The slots allow about 1½ inches of vertical adaptability.
Attach the top and bottom brackets to your rack.
NOTE: Contact your Leviton Sales Representative for information regarding custom bracket design and fabrication
services if you are unable to find a suitable manner for utilizing the included mounting brackets.
Optionally, the supplied button mounts may be used for mounting the PDU into cabinets supporting this
method of equipment mounting.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Installation
•7
Attaching the Expansion Module
Connect the Expansion Module PDU with the provided RJ11 crossover cable at the at the Link port on
the Switched PDU.
NOTE: The overall length of the RJ11 crossover cable should not exceed 10 feet.
Connecting to the Power Source
On 30A units, the input power cord is attached to the base of the unit. On units with a total maximum
output <30A, you must first attach the power cord to the unit before connecting the unit to the power
source.
To attach a power cord to the unit:
1.
2.
Plug the female end of the power cord firmly into its connector at the base.
Use a screwdriver to tighten the two screws on the retention bracket.
To connect to the power source:
Plug the male end of the power cord into the AC power source.
Connecting Devices
To avoid the possibility of noise due to arcing:
1.
2.
Keep the device’s on/off switch in the off position until after it is plugged into the outlet.
Connect devices to the PDU outlets.
NOTE: Leviton recommends even distribution of attached devices across all available outlets to avoid exceeding the
outlet, branch or phase limitations. See Power Ratings on page 53 for more information.
Always disconnect both power supply cords before opening to avoid electrical shock.
Afin d’éviter les chocs électriques, débranchez les cables électrique avant d’ouvrir.
Immer beiden Netzleitungen auskuppeln vor den Aufmachen um elektrischen Schlag zu vermeiden.
Connecting the Sensors
The Switched PDU is equipped with two mini RJ11 T/H ports for attachment of the included
Temperature/Humidity sensor. Attach the mini RJ11 plug of the sensor(s) to the appropriate T/H port.
Connecting to the Unit
Serial (RS232) port
The Switched Power Distribution Unit is equipped with an RJ45 Serial RS-232 port for attachment to a
PC or networked terminal server using the supplied RJ45 to RJ45 crossover cable and RJ45 to DB9F
serial port adapter as required. See Data Connections in Appendix C: Technical Specifications for
more information on the Serial RS-232 port.
Ethernet port
The Switched Power Distribution Unit is equipped with an RJ45 10/100Base-T Ethernet port for
attachment to an existing network. This connection allows access to the Switched PDU via Telnet or
HTML.
The Switched Power Distribution Unit is configured with the following network defaults to allow unit
configuration out-of-the-box through either Telnet or HTML:
•
•
•
IP address:
Subnet Mask:
Gateway:
192.168.1.254
255.255.255.0
192.168.1.1
The local PC network connection must be configured as noted below:
NOTE: Contact your system administrator for instructions in reconfiguring the network connection. Reconfiguration of
your network connection may require a restart to take effect.
•
•
8•
IP address:
Subnet Mask:
Installation
192.168.1.x (where x is 2-253)
255.255.255.0
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Chapter 3: Operations
INTERFACES
Outlet Naming and Grouping
Usernames and Passwords
10
10
10
HTML INTERFACE
Logging In
Outlet Control
Individual..............................................................................................................................12
Group....................................................................................................................................12
Environmental Monitoring
Input Load ............................................................................................................................13
Sensors..................................................................................................................................13
Configuration
System...................................................................................................................................13
Network ................................................................................................................................14
Telnet/SSH ............................................................................................................................14
HTTP/SSL .............................................................................................................................14
Serial Ports...........................................................................................................................15
Outlets ..................................................................................................................................15
Groups ..................................................................................................................................16
Users.....................................................................................................................................16
FTP .......................................................................................................................................17
SNTP.....................................................................................................................................17
SNMP....................................................................................................................................18
Tools
Restart ..................................................................................................................................19
Ping ......................................................................................................................................19
11
11
12
13
13
19
COMMAND LINE INTERFACE
Logging In
20
Operations Commands
22
Administration Commands
26
User Administration .............................................................................................................26
Outlet Administration ...........................................................................................................29
Group Administration...........................................................................................................31
Environmental Monitor Administration................................................................................32
Serial Port Administration....................................................................................................32
System Administration ..........................................................................................................33
TCP/IP Administration .........................................................................................................35
HTTP Administration ...........................................................................................................37
Telnet Administration ...........................................................................................................37
FTP Administration ..............................................................................................................38
SNTP Administration............................................................................................................39
20
Interfaces
The Switched Power Distribution Unit has two interfaces: the HTML interface accessed via the HTTP
enabled Ethernet connections and the command line for serial and Telnet connections.
Outlet Naming and Grouping
For commands requiring an outlet name, you may specify it in one of two ways: a predefined absolute
name or a descriptive name assigned by an administrator.
Absolute names are specified by a period (.) followed by a tower letter and outlet number. The tower
letter for the Switched PDU is A and the tower letter for the optional Expansion Module PDU is B.
Outlets may also be included in one or more named groups of outlets, enabling you to issue a command
that affects all outlets in a named group.
Usernames and Passwords
The Switched Power Distribution Unit has one predefined administrative user account
(username/password: admn/admn) and supports a maximum of 128 defined user accounts
NOTE: For security, Leviton recommends removal of the predefined administrative user account after a new account with
administrative rights has been created.
Only an administrative-level user may perform operations such as creating/removing user accounts and
command privileges, changing passwords and displaying user information. An administrator may also
view the status of all sensors and power inputs.
Usernames may contain from 1-16 characters and are not case sensitive; spaces are not allowed.
Passwords may contain up to 16 characters, and are case sensitive.
10 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
HTML Interface
The HTML interface is constructed of three major components: the System Location bar, the
User/Navigation bar and the Control Screen. The System Location bar displays the Leviton’s location
and IP address as well as the current Control Screen title. The User/Navigation bar displays the current
user and privilege level and provides access to all HTML pages. And the Control Screen is used to
display current data and allow changes to outlet states or system configuration.
The following sections describe each interface section/page and their use.
User/Navigation
System Location
Control Screen
Figure 3.1 Example HTML page
Logging In
Logging in through HTML requires directing the HTML client to the configured IP address of the unit.
To log in by HTML:
In the login window, enter a valid username and password and press OK.
If you enter an invalid username or password, you will be prompted again.
You are given three attempts to enter a valid username and password combination. If all three fail, the
session ends and a protected page will be displayed.
NOTE: The default Leviton username/password is admn/admn.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 11
Outlet Control
The Outlet Control section offers access to the Individual and Group outlet control pages. From the
Individual and Group pages, the user can review and manipulate power control functions for all outlets
and groups assigned to the current user. Both pages include the outlets absolute and descriptive names,
the Outlet Status reported to the Leviton PDU by the outlet, the current Control State being applied by
the Leviton PDU and the outlet load in amperes.
Available outlet and group power states may be set to on, off or reboot.
Individual
The Individual outlet control page displays all outlets assigned to the current user. The user may apply
on, off or reboot actions to individual, multiple or all accessible outlets.
To apply actions to individual or multiple outlets:
In the Individual Outlet Control section, select the desired action from the Control Action drop-down
menu for each individual outlet to be changed and press Apply.
To apply an action to all outlets:
In the Global Control section, select the desired action from the Control Action drop-down menu and
press Apply.
Group
The Group outlet control page displays all groups assigned to the current user as well as the outlets for
each group.
To select a group:
Select the group name from the drop-down menu and press Select. The page will refresh to display all
outlets associated to the selected group name.
To apply an action to a group:
Select the desired action from the drop-down menu and press Apply.
Outlet State/Control State Field Values
Outlet State
Control State
Description
On
On
Outlet is on
Off
Off
Outlet is off
Off
Pend On
Outlet is off and about to turn on in response to a sequence timer
Off
Reboot
Outlet is off and a Reboot action has been initiated
On
Idle On
A restart has occurred – Last Control State has been maintained
Off
Idle Off
A restart has occurred – Last Control State has been maintained
On
Wake On
A power-loss has occurred – Wakeup State has been applied
Off
Wake Off
A power-loss has occurred – Wakeup State has been applied
On/Wait
Off
Outlet state in transition – Requery of outlet status required
Off/Wait
On
Outlet state in transition – Requery of outlet status required
On/Error
varies
Error State – Outlet should be off but current is sensed at the outlet
Off/Error
varies
Error State – Outlet should be on but no current is sensed at the outlet
Off/Fuse
On
Outlet should be on but a blown fuse has been detected
No Comm
varies
Communication to the outlet has been lost*
* Control State will be applied when communication is re-established
12 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Environmental Monitoring
Input Load
The Input Load page displays the tower(s) absolute and descriptive name and the cumulative input load
in amperes of all devices attached to the Leviton PDU at the time the page was loaded. This page will
refresh automatically every 10 seconds
Sensors
The Sensors page displays:
•
•
Temperature/humidity sensor’s absolute and descriptive names
Temperature/humidity sensor readings in degrees Celsius and percent relative humidity
Configuration
The Configuration section offers access to all unit configuration options including Network,
Telnet/SSH, HTTP/SSL, Serial Ports, Users, FTP, Proxy/SNTP and SNMP. This section is available to
administrative level users only.
System
The System configuration page is used for reference of system information such as Ethernet NIC Serial
Number, Ethernet MAC address and system firmware and hardware revisions as well as assignment and
maintenance of the system location and tower descriptive names.
For description names, up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal –
spaces are not allowed) are allowed.
NOTE: Spaces may be used for the location description only.
Creating a descriptive system location name:
Enter a descriptive name and press Apply.
Configuring the Input Current LED display orientation:
Select Normal or Inverted from the drop-down menu and press Apply.
Creating a descriptive unit name:
Click on the Tower Names link.
On the subsequent Tower Names page, enter a descriptive name and press Apply.
Creating a descriptive input feed name:
Click on the Input Feed Names link.
On the subsequent Input Feed Names page, enter a descriptive name and press Apply.
Creating a descriptive outlet name:
Click on the Outlet Names link which will open the Outlets configuration page. See Outlets on page
15 for additional information on creating descriptive outlet names.
Creating a descriptive serial port name:
Click on the Serial Port Names link which will open the Serial Ports configuration page. See Serial
Ports on page 15 for additional information on creating descriptive serial port names.
Creating a descriptive Environmental Monitor name:
Click on the Environmental Monitor Names link.
On the subsequent Environmental Monitor Names page, enter a descriptive name and press Apply.
Creating descriptive sensor names:
Click on the Sensor Names link.
On the subsequent Sensor Names page, enter a descriptive name and press Apply.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 13
Network
The Network configuration page is used for maintenance of the network interface. From this page an
administrator may configure the IP address, subnet mask, gateway address, DNS addresses as well as
view the link status, speed and duplex value.
The PDU is configured with the following network defaults to allow unit configuration out-of-the-box
through either Telnet or HTML:
• IP address:
192.168.1.254
• Subnet Mask:
255.255.255.0
• Gateway:
192.168.1.1
The initial local PC network connection must be configured as noted below:
NOTE: Contact your system administrator for instructions in reconfiguring the network connection. Reconfiguration of
your network connection may require a restart to take effect.
•
•
IP address:
Subnet Mask:
192.168.1.x (where x is 2-253)
255.255.255.0
NOTE: The unit must be restarted after network configuration changes. See Performing a warm boot: on page 19.
Setting the IP address, subnet mask, gateway or DNS address:
In the appropriate field, enter the IP address, subnet mask, gateway address or DNS address and press Apply.
Telnet/SSH
The Telnet/SSH configuration page used to enable or disable Telnet and SSH support and configure the
port number that the Telnet or SSH server watches. For more information on SSH see page 43 in
Chapter 4: Advanced Operations.
Enabling or disabling Telnet or SSH support:
Select Enabled or Disabled from the appropriate Server drop-down menu and press Apply.
Changing the Telnet or SSH server port number:
In the appropriate Port field, enter the port number and press Apply.
HTTP/SSL
The HTTP/SSL configuration page used to enable or disable HTTP and SSL support, configure the port
number that the HTTP server watches and responds to, selection of the method of authentication used
and SSL access level. For more information on SSL see page 41 in Chapter 4: Advanced Operations.
Enabling or disabling HTTP or SSL support:
Select Enabled or Disabled from the appropriate Server drop-down menu and press Apply.
Changing the HTTP server port number:
In the HTTP Port field, enter the port number and press Apply.
Setting the HTTP authentication method:
The Leviton HTTP server supports two authentication methods for security and validation of the
username-password – Basic and MD5 digest.
The Basic method utilizes Base64 encoding to encode and deliver the username-password over the
network to the HTTP server for decoding and authentication. This basic method is supported by all
web browsers and offers a minimum level of security.
NOTE: The Base64 algorithm is widely-known and susceptible to packet-sniffer attack for acquisition of the encoded
username-password string.
The MD5 digest method provides stronger protection utilizing one-way encoded hash numbers, never
placing the username-password on the network. Instead, the sending browser creates a challenge code
based on the hash algorithm, provided username-password and unique items such as the device IP
address and timestamp, which is compared against the HTTP server internal user database of valid
challenge codes. The MD5 digest method offers a higher level of security than the Basic method but at
present is not supported by all browsers.
NOTE: MD5 is known to be fully supported by Internet Explorer 5.0+
Select Basic or MD5 from the Authentication drop-down menu and press Apply.
14 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Setting SSL access level
Leviton SSL supports configuration of SSL connections as being either optional or required. The
default access level is set to optional.
•
•
Optional –Both non-secure (HTTP) and SSL encrypted connections (HTTPS) are allowed access.
Required – ONLY SSL encrypted connections (HTTPS) are allowed access.
Select Optional or Required from the Secure Access drop-down menu and press Apply.
Serial Ports
The Serial Ports configuration page is used for maintenance of the serial port.
NOTE: Pass-Thru connections may only be initiated from the command line interface via a Telnet/SSH session.
Setting the data-rate for all serial ports:
Select the serial port data-rate from the drop-down menu and press Apply.
Setting the serial port timeout value:
Enter the timeout value (in minutes) in the Connection Timeout field and press Apply.
Creating a descriptive serial port name:
Click on the Edit link in the Action column next to the port to be configured.
On the subsequent Serial Port Edit page, enter the descriptive name. Up to 24 alphanumeric and other typeable
characters (ASCII 33 to 126 decimal, spaces are not allowed) are allowed. Press Apply.
Enabling or disabling serial port active signal checking:
Click on the Edit link in the Action column next to the port to be configured.
On the subsequent Serial Port Edit page, select On or Off from the DSR Check drop-down menu and press Apply.
Outlets
The Outlets configuration page is used for assignment and/or editing of outlet sequence and reboot
timers, descriptive names and wakeup states.
Setting the outlet sequencing interval:
Enter the sequencing interval (in seconds) in the Sequence Interval field and press Apply.
Setting the outlet reboot delay:
Enter the reboot interval (in seconds) in the Reboot Delay field and press Apply.
Editing the outlet descriptive name:
Click on the Edit link in the Action column next to the outlet to be configured.
On the subsequent Outlet Edit page, enter the descriptive name. Up to 24 alphanumeric and other
typeable characters (ASCII 33 to 126 decimal, spaces are not allowed) are allowed. Press Apply.
Changing the outlet wakeup state:
Click on the Edit link in the Action column next to the outlet to be configured.
On the subsequent Outlet Edit page, select On, Off or Last from the Wakeup State drop-down menu
and press Apply.
Setting the outlet Post-On delay:
Click on the Edit link in the Action column next to the outlet to be configured.
On the subsequent Outlet Edit page, enter the outlet Post-On delay (in seconds) in the Post-On Delay
field and press Apply.
For more information on outlet Post-On delays, see Outlet Administration on page 29.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 15
Groups
The Groups configuration page is used for creation and deletion of group and assignment of outlets to
groups.
Creating a group:
Enter a descriptive group name in the Group Name field. Up to 24 alphanumeric and other typeable
characters (ASCII 33 to 126 decimal, spaces are not allowed) are allowed. Press Apply.
Removing a group:
Click on the Remove link in the Action column for the group to be removed and press Yes on the
subsequent confirmation window.
Adding and Deleting outlets from a group:
Press the Edit link in the Action column for the associated group.
On the subsequent Group Edit page, select or deselect outlets to be included in that group. Press
Apply.
Users
The Users configuration page is used for creation and removal of usernames, assignment of accessible
outlets and group, assignment of privilege levels and the changing of user passwords.
Creating a new user:
Enter a user name in the Username field. Up to 16 alphanumeric and other typeable characters (ASCII
33 to 126 decimal, spaces are not allowed) are allowed.
Enter a password for the new user and verify in the Password and Verify Password fields. For security,
password characters are not displayed. Press Apply.
Removing a user:
Click on the Remove link in the Action column for the user to be removed and press Yes on the
subsequent confirmation window.
Changing a user password:
Click on the Edit link in the Action column for the associated user.
On the subsequent User Edit page, enter a password and verify the new password for the new user in the
Password and Verify Password fields. For security, password characters are not displayed. Press Apply.
Changing a user’s access privilege level:
The PDU has four defined access privilege levels; Admin, User, On-Only and View-Only:
•
Admin:
Full-access for all configuration, control (On, Off, Reboot), status and Pass-Thru.
•
User:
Partial-access for control (On, Off, Reboot), status and Pass-Thru of assigned
outlets, groups and serial/Pass-Thru ports.
•
On-Only:
Partial-access for control (On), status and Pass-Thru of assigned outlets, groups
and serial/Pass-Thru ports.
•
View-Only: Partial-access for status and Pass-Thru of assigned outlets, groups and
serial/Pass-Thru ports.
The administrator may also grant administrative privileges to other user accounts allowing the PDU to have
more than one administrative-level user.
NOTE: You cannot remove administrative privileges from the Admn user unless another user has already been given
administrative access level privileges created.
Click on the Edit link in the Action column for the associated user.
On the subsequent User Edit page, select Admin, User, On-only or View-only from the Access Level
drop-down menu and press Apply.
16 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Granting or removing Environmental Monitoring viewing privileges:
Click on the Edit link in the Action column for the associated user.
On the subsequent User Edit page, select Yes or No from the Environmental Monitoring drop-down
menu and press Apply.
Adding and Deleting outlet access:
Click on the Outlets link in the Access column for the associated user.
On the subsequent User Outlets page, select or deselect outlets to be accessed by the user and press Apply.
Adding and Deleting group access:
Click on the Groups link in the Access column for the associated user.
On the subsequent User Groups page, select or deselect group to be accessed by the user and press Apply.
Adding and Deleting serial port access:
Click on the Ports link in the Access column for the associated user.
On the subsequent User Ports page, select or deselect ports to be accessed by the user and press Apply.
FTP
The FTP configuration page is used for setup and maintenance of all settings required to perform an
FTP firmware upload. See Appendix B: Uploading Firmware for more information on uploading
firmware.
Setting the FTP Host IP Address:
Enter the IP address in the Host IP Address field and press Apply.
Setting the FTP username:
Enter the FTP server username in the Username field, and press Apply.
Setting the FTP password:
Enter the FTP server password in the Password field, and press Apply.
Setting the filepath:
Enter the path of the file to be uploaded in the Directory field, and press Apply.
Setting the filename for upload:
Enter the filename of the file to be uploaded in the Filename field, and press Apply.
Testing the FTP upload configuration:
This test validates that the unit is able to contact and log onto the specified FTP server, download the
firmware file and verify that the firmware file is valid for this unit.
Press Test.
SNTP
The SNTP configuration page is used for setup and maintenance of SNTP support.
Setting the SNTP Server Address:
Enter the IP address in the primary and/or secondary address field and press Apply.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 17
SNMP
The SNMP configuration page is used for setup and maintenance of all settings required to enable
SNMP support as well as access to the trap configuration pages. For additional information on SNMP
support and detailed descriptions of available traps, see SNMP on page 44.
NOTE: Traps are generated according to a hierarchical architecture; i.e. if a Tower Status enters a trap condition, only the
Tower Status trap is generated. Infeed and Outlet Status traps are suppressed until the Tower Status returns to Normal.
Enabling or disabling SNMP support:
Select Enabled or Disabled from the drop-down menu and press Apply.
Setting the community strings:
Enter the community string in the appropriate field and press Apply.
Community strings may be 1 to 24 characters
Setting the trap timer:
Enter a trap timer value in the Error Trap Repeat Time field and press Apply.
The Error Trap Repeat Time value may be 1 to 65535 (in seconds).
Setting trap destinations:
Enter an IP address in the appropriate Trap Destination field and press Apply.
Enabling or disabling tower traps:
Click on the Tower Traps link.
On the subsequent Tower Traps page, select or deselect the desired traps and press Apply.
Configuring input feed traps:
Click on the Input Feed Traps link.
On the subsequent Input Feed Traps page, select or deselect the desired traps and press Apply.
For Load traps, enter a maximum load value for the infeed in the High Load Threshold field and press Apply.
The High Load Threshold value may be 0 to 255 (in amperes).
Enabling or disabling Environmental Monitor traps:
Click on the Environmental Monitor Traps link.
On the subsequent page, select or deselect the desired traps and press Apply.
Configuring the Temperature-Humidity sensor traps:
Click on the Sensor Traps link.
On the subsequent page, select or deselect the desired traps and press Apply.
For Temp traps, enter a minimum and maximum threshold value for the sensor in the appropriate field
and press Apply.
The threshold value may be 0 to 127 (in degrees Celsius).
For Humid traps, enter a minimum and maximum threshold value for the sensor in the appropriate field
and press Apply.
The threshold value may be 0 to 100 (in percent relative humidity).
Configuring outlet traps:
Click on the Outlet Traps link.
On the subsequent Outlet Traps page, select or deselect the desired traps and press Apply.
18 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Tools
The Tools section contains access to rebooting the unit, uploading new firmware as well as resetting the unit to
factory defaults. This section is available to administrative level users only.
Restart
Performing a warm boot:
Select the Restart from the Action drop-down menu and press Apply.
Note: System user/outlet/group configuration or outlet states are NOT changed or reset with this command.
Resetting to factory defaults:
See Chapter 5: for more information on resetting a PDU to factory defaults from the HTML interface.
Uploading new firmware:
See Appendix B: for more information on uploading new firmware from the HTML interface.
Ping
The Ping feature may be used to test the PDU’s ability to contact another Ethernet enabled device’s IP
address. For LDAP support, it may also be used to test the configuration of the Domain Name server
IP address by testing for proper name resolution.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 19
Command Line Interface
Logging In
Logging in through Telnet requires directing the Telnet client to the configured IP address of the unit.
Logging in through the Console (RS232) port requires the use of a terminal or terminal emulation
software configured to support ANSI or VT100 and a supported data rate (300, 1200, 2400, 4800, 9600,
19200, 38400, 57600, or 115200 BPS) - 8 data bits-no parity-one stop bit and Device Ready output
signal (DTR or DSR).
To log in by RS-232 or Telnet:
1.
Press Enter. The following appears, where x.xx is the firmware version:
Leviton Version x.xx
Username:
NOTE: Logging in by Telnet will automatically open a session. It is not necessary to press Enter.
2.
At the Username: and Password: prompts, enter a valid username and password. And press Enter.
You are given three attempts to enter a valid username and password combination. If all three fail,
the session ends.
NOTE: The default Leviton username/password is admn/admn.
When a valid username and password is entered, the command prompt appears. If a location identifier
was defined, it will be displayed before the prompt. See Creating a location description on page 33 for
more information.
Commands may be entered in any combination of uppercase and lowercase. All command characters must
be enteredcorrectly; there are no command abbreviations. A user must have administrative privileges to
use the administration commands. The following tables list and briefly describe each command.
Operations Command Summary
Command
Description
On
Turns one or more outlets on
Off
Turns one or more outlets off
Reboot
Reboots one or more outlets
Status
Displays the on/off status of one or more outlets
ILoad
Displays the total cumulative input load
Istat
Displays the status of the infeeds
Connect
Connects to a serial/Pass-Thru port
Login
Ends the current session and brings up the Username: prompt
Logout
Ends a session
Quit
Ends a session
List Outlets
Lists all accessible outlets for the current user
List Ports
Lists all accessible serial/Pass-Thru ports for the current user
List Group
Lists all assigned outlets for a group name
List Groups
Lists all accessible groups for the current user
Administrative Command Summary
Add Grouptouser
Grants a user access to one or more groups
Add Outlettogroup
Adds an outlet to a group name
Add Outlettouser
Grants a user access to one or all outlets
Add Porttouser
Grants a user access to one or all serial/Pass-Thru ports
Create Group
Adds a group name
Create User
Adds a user account
Delete Groupfromuser
Removes access to one or more groups for a user
Delete Outletfromgroup Deletes an outlet from a group name
Delete Outletfromuser
Removes access to one or all outlets for a user
Delete Portfromuser
Removes access to one or all serial/Pass-Thru ports
20 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Administrative Command Summary (continued)
List User
Displays all accessible outlets/groups/ports for a user
List Users
Displays privilege levels for all users
Remove Group
Deletes a group name
Remove User
Deletes a user account
Restart
Performs a warm boot
Set Display
Sets the LED orientation for external Input Current displays
Set DNS
Sets the IP address of the Domain Name server
Set Envmon Name
Specifies a descriptive field fro the integrated Environmental Monitor
Set Envmon THS Name Specifies a descriptive field for a temperature-humidity sensor
Set FTP Filename
Specifies the file to be uploaded via FTP
Set FTP Filepath
Specifies the filepath for the file to be uploaded
Set FTP Host
Sets the FTP Host IP address
Set FTP Password
Sets the password for the FTP Host
Set FTP Username
Sets the username for the FTP Host
Set Gateway
Sets the Gateway
Set HTTP
Enables or disables HTTP access
Set HTTP Port
Specifies the target port for HTTP access
Set HTTP Security
Specifies the HTTP server authentication method
Set Infeed Name
Specifies a descriptive field for the infeed
Set Ipaddress
Sets the IP address
Set Location
Specifies a descriptive field for the HTML control screen and login banner
Set Outlet Name
Specifies a descriptive field for a device attached to an outlet
Set Outlet PostOnDelay Sets the Post-On delay for an outlet
Set Outlet RebootDelay Sets the reboot delay for all outlets
Set Outlet SeqInterval
Sets the sequencing interval for all outlets
Set Outlet Wakeup
Sets the wakeup state for an outlet
Set Subnet Mask
Sets the Subnet Mask
Set Telnet Port
Sets the Telnet server port number
Set Telnet
Enables or disables Telnet access
Set Tower Name
Specifies a descriptive field for the PDU
Set User Access
Sets the access level for a user
Set User Envmon
Grants or removes privileges to view input and environmental monitoring status
Set User Password
Changes the password for a user
Set Port Name
Specifies a descriptive field for a serial/Pass-Thru port
Set Port Dsrchk
Sets the DSR active signal checking for a serial/Pass-Thru port
Set Port Speed
Set the connection speed for all serial/Pass-Thru ports
Set Port Timeout
Sets the inactivity timer for Pass-Thru sessions
Show FTP
Displays FTP configuration information
Show Infeeds
Displays infeed configuration information
Show Network
Display network configuration information
Show Outlets
Displays configuration information for all outlets
Show Ports
Displays serial/Pass-Thru port configuration information
Show System
Displays system configuration information
Show Towers
Displays tower configuration information
Version
Displays the Leviton firmware version
To display the names of commands that you may execute:
At the command prompt, press Enter. A list of valid commands for the current user appears.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 21
Operations Commands
Operations commands manage outlet states, provide information about the PDU environment and
control session operations.
Turning outlets on
The On command turns on one or more outlets. When the command completes, a display indicating all
outlets affected and their current states will be displayed.
To turn outlets on:
At the Switched PDU: prompt, type on, followed by an outlet name, and press Enter, or
Type on, followed by a group name, and press Enter, or
Type on all and press Enter.
Examples
The following command turns the second outlet on, using the outlet’s absolute name:
Switched PDU: on .a2<Enter>
The following command turns on all the outlets in the group named ServerGroup_1:
Switched PDU: on ServerGroup_1<Enter>
Turning outlets off
The Off command turns off one or more outlets. When the command completes, a display indicating all
outlets affected and their current states will be displayed.
To turn outlets off:
At the Switched PDU: prompt, type off, followed by an outlet name, and press Enter, or
Type off, followed by a group name, and press Enter, or
Type off all and press Enter
Examples
The following command turns off the outlet named FileServer_1:
Switched PDU: off FileServer_1<Enter>
The following command turns off all outlets:
Switched PDU: off all<Enter>
Rebooting outlets
The Reboot command reboots one or more outlets. This operation turns the outlet(s) off, delays for a
user configurable period and then turns the outlet(s) on. When the command completes, a display
indicating all outlets affected and their current states will be displayed.
NOTE: It is necessary to reissue the Status command to verify that the outlets have rebooted. See Displaying outlet status
for more information.
To reboot one or more outlets:
At the Switched PDU: prompt, type reboot, followed by an outlet name, and press Enter, or
Type reboot, followed by a group name, and press Enter, or
Type reboot all and press Enter.
Example
The following command reboots all the outlets in the group named ServerGroup_1:
Switched PDU: reboot ServerGroup_1<Enter>
22 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Displaying outlet status
The Status command displays the on/off status of one or more outlets. The command displays the status of
only those outlets for which the current username has power control access.
This display includes the outlet absolute and descriptive names, the Outlet State reported to the PDU by
the outlet and the current Control State being applied by the PDU. If you do not specify any parameter
with this command, the status of all accessible outlets is displayed.
NOTE: If the user has access to more than 16 total outlets, the Status command will display the first 16 outlets with a
prompt to view the remaining outlets.
For more information on outlet and control state values, see Outlet Control on page 12.
To display on/off status of one or more outlets:
At the Switched PDU: prompt, type status, followed by an outlet name, and press Enter, or
Type status, followed by a group name, and press Enter, or
Type status and press Enter.
Examples
The following command displays the on/off status of the outlet named FileServer_1:
Switched PDU: status FileServer_1<Enter>
Outlet
ID
Outlet
Name
Outlet
State
Control
State
.A3
FileServer_1
On
On
The following command displays the on/off status of all accessible outlets:
Switched PDU: status<Enter>
Outlet
ID
Outlet
Name
Outlet
State
Control
State
.A1
.A2
.A3
.A4
.A5
.A6
.A7
.A8
.A9
.A10
.A11
.A12
.A13
.A14
.A15
.A16
DataServer_1
WebServer_1
FileServer_1
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
More (Y/es N/o):
The following command displays the on/off status for outlets in the group ServerGroup_1:
Switched PDU: status ServerGroup_1<Enter>
Group: ServerGroup_1
Outlet
ID
Outlet
Name
Outlet
State
Control
State
.A1
.A2
.A3
DataServer_1
WebServer_1
FileServer_1
On
On
On
On
On
On
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 23
Displaying accessible outlets
The List Outlets command displays accessible outlets for the current user. The display includes the
absolute and descriptive name of all outlets assigned to the current user.
To display accessible outlets:
At the Switched PDU: prompt, type list outlets and press Enter.
Example
The follow command displays all accessible outlets for the current user:
Switched PDU: list outlets<Enter>
Outlet
ID
Outlet
Name
.A1
.A2
DataServer_1
WebServer_1
Displaying accessible groups
The List Groups command displays accessible groups for the current user.
To display accessible groups:
At the Switched PDU: prompt, type list groups and press Enter.
Example
The follow command displays all accessible groups for the current user:
Switched PDU: list groups<Enter>
Groups:
ServerGroup_1
RouterGroup_1
Displaying outlets assigned to a group
The List Group command displays outlets assigned to the specified group name.
To display outlets assigned to a group:
At the Switched PDU: prompt, type list group, followed by the group name and press Enter.
Example
The follow command displays the outlets assigned to the group ServerGroup_1:
Switched PDU: list group ServerGroup_1<Enter>
Group: ServerGroup_1
Outlet
ID
Outlet
Name
.A1
.A2
.A3
DataServer_1
WebServer_1
FileServer_1
Displaying accessible serial ports
The List Ports command displays accessible serial ports for the current user.
To display accessible serial ports:
At the Switched PDU: prompt, type list ports and press Enter.
Example
The follow command displays all accessible serial ports for the current user:
Switched PDU: list ports<Enter>
Port
ID
Port
Name
Console
Console
24 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Displaying infeed status
The Istat or Iload command displays the status of one or more infeed.
This display includes the infeed absolute and descriptive names and the Input Status and current Load
reported to the PDU by the infeed.
To display status of one or more infeeds:
Type istat and press Enter, or
Type iload and press Enter.
Examples
The following command displays the infeed status:
Switched PDU: istat
Input
Feed ID
Input
Feed Name
Input
Status
Input
Load
.AA
HQ_1_Infeed_A
On
10.5 Amps
Connecting to a serial device
The Connect command allows Pass-Thru serial connection to devices attached to the standard serial
port (Console).
To connect to a serial device:
At the Switched PDU: prompt, type connect console and press Enter.
To disconnect from a serial device:
Type !*break and press Enter.
Displaying the status of the Environmental Monitor
The Envmon command displays the status of the integrated Environmental Monitor.
By default, only administrative user accounts are allowed access to the Envmon command. An
administrator may user the Set User Envmon command to enable and disable access for other user
accounts.
To display the status of the Environmental Monitor:
At the Switched PDU: prompt, type envmon and press Enter.
Example
The following command displays the status of the Environmental Monitor.
Switched PDU: envmon<Enter>
Environmental Monitor .A
Name: Florida_HQ_1
Status: Normal
Temperature/Humidity Sensors
ID
.A1
.A2
Name
Temp_Humid_Sensor_A1
T/H2_Florida_HQ_1
Temperature
Not Found
23.5 Deg. C
Humidity
Not Found
22 % RH
Starting a new session
The Login command activates the Username: prompt. The current session ends, allowing a user to log
in and start a new session under a different username.
To start a new session:
At the Switched PDU: prompt, type login and press Enter. The Username: prompt appears.
Ending a session
The Quit or Logout commands ends a session. A session ends automatically when no activity is
detected for five minutes, or upon loss of connection.
To end a session:
At the Switched PDU: prompt, type quit and press Enter, or
Type logout and press Enter.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 25
Administration Commands
Administration commands may only be issued by a user with administrative privileges, such as the
predefined Admn user or another user who has been granted administrative privileges with the Set User
Admnpriv command.
User Administration
Creating a user account
The Create User command creates a user account with the specified username and password. See
Usernames and Passwords in this chapter for more information.
To create a user account:
At the Switched PDU: prompt, type create user, optionally followed by a 1-16 character username
(Spaces are not allowed, and usernames are not case sensitive). Press Enter.
At the Password: prompt, type a password of up to 16 alphanumeric and other typeable characters
(ASCII 32 to 126 decimal). Passwords are case sensitive. Press Enter. To specify no password, press
Enter at the prompt.
At the Verify Password: prompt, retype the password. Press Enter. To verify no password, press Enter
at the prompt.
Example
The following command creates the user account JaneDoe:
Switched PDU: create user JaneDoe<Enter>
Password: <Enter>
Verify New Password: <Enter>
For security, password characters are not displayed.
Removing a user account
The Remove User command removes a user account.
NOTE: You may remove the predefined user account Admn only if another user account has been granted administrative
privileges using the Set User Admnpriv command.
To remove a user account:
At the Switched PDU: prompt, type remove user, optionally followed by a username. Press Enter.
Changing a password
The Set User Password command changes a user’s password. For security, when you type a password,
the characters are not displayed on the screen. See Usernames and Passwords for more information.
To change a password:
At the Switched PDU: prompt, type set user password, followed by a username and press Enter.
At the Password: prompt, type the new password and press Enter. Passwords may contain up to 16
characters, and spaces are not allowed. To specify no password, press Enter at the prompt.
At the Verify Password: prompt, retype the new password and press Enter. To verify no password,
press Enter at the prompt.
Examples
The following command changes the password for the user JohnDoe:
Switched PDU: set user password johndoe<Enter>
Password: <Enter>
Verify Password: <Enter>
The following command blanks the password for the user JaneDoe:
Switched PDU: set user password<Enter>
Username: janedoe<Enter>
Password: <Enter>
Verify Password: <Enter>
26 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Setting user access level privileges
The Set User Access command sets the access level privileges for a user. The PDU has four defined
access privilege levels; Admin, User, On-Only and View-Only. For more information on user access
levels, see Changing a user’s access privilege level: on page 16.
The administrator may also grant administrative privileges to other user accounts allowing the PDU to have
more than one administrative-level user.
NOTE: You cannot remove administrative privileges from the Admn user unless another user has already been given
administrative access level privileges created.
To set the access level privilege for a user:
At the Switched PDU: prompt, type set user access, followed by admin or user, optionally followed
by a username and press Enter.
Examples
The following command sets the user access level for JohnDoe to Admin:
Switched PDU: set user access admin johndoe<Enter>
The following command sets the user access level for JaneDoe to User:
Switched PDU: set user access user janedoe<Enter>
Granting and removing input load viewing privileges
The Set User Envmon command grants or removes input status viewing privileges to/from a user.
To grant or remove input load viewing privileges for a user:
At the Switched PDU: prompt, type set user envmon followed by on or off, optionally followed by a
username and press Enter.
Example
The following command grants input load privileges to the user JohnDoe:
Switched PDU: set user envmon on johndoe<Enter>
Displaying the access privilege levels
The List Users command displays all defined users with their access privilege level.
To display user access privilege levels:
At the Switched PDU: prompt, type list users and press Enter.
Example
The following command displays all users with their access privilege level:
Switched PDU: list users<Enter>
User
Name
Privilege
Level
Environmental
Monitoring
JOHNDOE
JANEDOE
JOSEYDOE
JOEDOE
Admin
User
On-Only
View-Only
Allowed
Allowed
Not Allowed
Not Allowed
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 27
Adding outlet access to a user
The Add OutletToUser command grants a user access to one or all outlets. To grant access for more
than one outlet, but not all outlets, you must use multiple Add OutletToUser commands.
To grant outlet access to a user:
At the Switched PDU: prompt, type add outlettouser, optionally followed by an outlet name and a
username. Press Enter, or
Type add outlettouser all, followed by a username and press Enter.
Examples
The following commands grant the user JaneDoe access to outlets A1 and Webserver_1:
Switched PDU:add outlettouser .a1 janedoe<Enter>
Switched PDU:add outlettouser WebServer_1 janedoe<Enter>
Deleting outlet access for a user
The Delete OutletFromUser command removes a user’s access to one or all outlets. You cannot remove
access to any outlet for an administrative level user.
To delete outlet access for a user:
At the Switched PDU: prompt, type delete outletfromuser, optionally followed by an outlet name and
a username. Press Enter, or
Type delete outletfromuser all, followed by a username and press Enter.
Adding group access to a user
The Add GroupToUser command grants a user access to a group. To grant access for more than one
group, you must use multiple Add GroupToUser commands.
To grant group access to a user:
At the Switched PDU: prompt, type add grouptouser, optionally followed by a group name and a
username. Press Enter.
Examples
The following commands grants to user JaneDoe access to the groups ServerGroup_1 and
ServerGroup_2:
Switched PDU:add GroupToUser ServerGroup_1 janedoe<Enter>
Switched PDU:add GroupToUser ServerGroup_2 janedoe<Enter>
Deleting group access for a user
The Delete GroupFromUser command removes a user’s access to a group. You cannot remove access
to any group for an administrative level user.
To delete group access for a user:
At the Switched PDU: prompt, type delete GroupFromUser, optionally followed by a group name and
a username. Press Enter.
Adding serial port access to a user
The Add PortToUser command grants a user access to the serial port.
To grant serial port access to a user:
At the Switched PDU: prompt, type add porttouser console and a username. Press Enter.
Deleting serial port access for a user
The Delete PortFromUser command removes a user’s access to the serial port. You cannot remove
access to the serial port for an administrative level user.
To delete serial port access for a user:
At the Switched PDU: prompt, type delete portfromuser console and a username. Press Enter.
28 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Displaying user outlet, group and serial port access
The List User command displays all accessible outlets, groups and serial ports for a user.
To display user outlet, group and serial port access:
At the Switched PDU: prompt, type list user, optionally followed by a username. Press Enter.
Example
The following command displays information about the user JaneDoe:
Switched PDU: list user janedoe<Enter>
Username: JANEDOE
Outlet
ID
Outlet
Name
.A1
.A2
DataServer_1
WebServer_1
Groups:
ServerGroup_1
ServerGroup_2
More (Y/es N/o): Y
Ports:
Port
ID
Port
Name
Console
Console
JaneDoe may access the following outlets, groups and serial ports: outlet A1 which has a descriptive
name of DataServer_1, outlet A2 which has a descriptive name of WebServer_1, group ServerGroup_1
group ServerGroup_2, and Console serial port.
Outlet Administration
Setting the sequencing interval
The Set Outlet SeqInterval commands sets the power on sequencing interval for all outlets.
To set the sequencing interval:
At the Switched PDU: prompt, type set outlet seqinterval all, followed by a value from 2 to 15 (in
seconds) and press Enter.
Setting the reboot delay
The Set Outlet RebootDelay commands sets the reboot delay for all outlets.
To set the sequencing interval:
At the Switched PDU: prompt, type set outlet rebootdelay all, followed by a value from 5 to 60 (in
seconds) and press Enter.
Creating a descriptive outlet name
The Set Outlet Name command assigns a descriptive name to an outlet. You may use this name in
commands that require an outlet name as an alternative to using the outlet’s absolute name.
To create an outlet name:
At the Switched PDU: prompt, type set outlet name, followed by the absolute outlet name and a
descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal spaces are not allowed). Outlet names are not case sensitive. Press Enter.
Example
The following command adds the descriptive name DataServer_1 to outlet .a1:
Switched PDU: set outlet name .a1 DataServer_1<Enter>
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 29
Setting the outlet wakeup state
The Set Outlet Wakeup command set the default wakeup state for that outlet. In the event of a systemwide power loss, this state will be applied to the outlet when power is restored.
The wakeup state may be set to On, Off or Last. Upon restoration of system power; If set to On, the PDU
will apply power to that outlet. If set to Off, the PDU will not apply power to that outlet. If set to Last, the
PDU will apply the last known power state.
To set the wakeup state:
At the Switched PDU: prompt, type set outlet wakeup, followed by on, off or last and the outlet name.
Press Enter.
Example
The following command sets the wakeup state for outlet .a1 to off:
Switched PDU: set outlet wakeup off .a1<Enter>
Setting the outlet Post-On delay
The Set Outlet PostOnDelay command is used set the Post-On delay for an outlet. This feature allows
the administrator to manage boot dependencies during power-on sequencing or group commands by
delaying the sequencing of subsequent outlets after an outlet has been powered on.
NOTE: This delay is applied in addition to the general sequencing interval.
To set the outlet Post-On delay
At the Sentry: prompt, type set outlet postondelay, followed by a value from 0 to 900 (in seconds) and
press Enter.
Example
The following command set the Post-On delay for outlet .a5 to 90 seconds:
Sentry:
set outlet postondelay .a5 90<Enter>
Displaying outlet information
The Show Outlets command displays information about all outlets. This information includes:
•
•
•
Sequencing and reboot timer values
Descriptive outlet name, if applicable
Outlet wakeup state setting
To display outlet information:
At the Switched PDU: prompt, type show outlets and press Enter.
Example
The following command displays all outlet information:
Switched PDU: show outlets<Enter>
Outlet
ID
Outlet
Name
Wakeup
State
Post-On
Delay (seconds)
.A1
.A2
.A3
.A4
.A5
.A6
.A7
.A8
.A9
.A10
.A11
.A12
.A13
.A14
.A15
.A16
TowerA_Outlet1
TowerA_Outlet2
TowerA_Outlet3
TowerA_Outlet4
TowerA_Outlet5
TowerA_Outlet6
TowerA_Outlet7
TowerA_Outlet8
TowerA_Outlet9
TowerA_Outlet10
TowerA_Outlet11
TowerA_Outlet12
TowerA_Outlet13
TowerA_Outlet14
TowerA_Outlet15
TowerA_Outlet16
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
30
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
More (Y/es N/o):
Outlet Options:
Sequence Interval:
Reboot Delay:
30 • Operations
2 seconds
15 seconds
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Group Administration
Creating a group name
The Create Group command creates a new group name.
To create a group name:
At the Switched PDU: prompt, type create group, optionally followed by a descriptive name of up to 24
alphanumeric and other typeable characters (ASCII 33 to 126 decimal - spaces are not allowed. Group
names are not case sensitive). Press Enter.
Example
The following command creates group name ServerGroup_1:
Switched PDU: create group ServerGroup_1<Enter>
Removing a group name
The Remove Group command removes a group name.
To remove a group name:
At the Switched PDU: prompt, type remove group, optionally followed by a username. Press Enter.
Example
The following command removes group name ServerGroup_1:
Switched PDU: remove group ServerGroup_1<Enter>
Adding an outlet to a group
The Add OutletToGroup command adds an outlet to a group. To add more than one outlet, but not all
outlets, you must use multiple Add OutletToGroup commands.
To add an outlet to a group:
At the Switched PDU: prompt, type add outlettogroup, optionally followed by an outlet name and
group name. Press Enter, or
Type add OutletToGroup, followed by all and the group name. Press Enter.
Examples
The following commands uses absolute outlet names to add outlets A1 and A2 to group name
ServerGroup_1:
Switched PDU:add OutletToGroup .a1 ServerGroup_1<Enter>
Switched PDU:add OutletToGroup .a2 ServerGroup_1<Enter>
The following commands usese the outlets’ descriptive names to add outlets DataServer_1 and
WebServer_1 to group name ServerGroup_1:
Switched PDU:add OutletToGroup DataServer_1 ServerGroup_1<Enter>
Switched PDU:add OutletToGroup WebServer_1 ServerGroup_1<Enter>
The following command add all outlets to group name ServerGroup_1:
Switched PDU: add OutletToGroup<Enter>
Outletname: all<Enter>
Groupname: ServerGroup_1<Enter>
Deleting an outlet from a group
The Delete OutletFromGroup command deletes an outlet from a group. To delete more than one outlet,
but not all outlets, you must use multiple Delete OutletToGroup commands.
To delete an outlet from a group:
At the Switched PDU: prompt, type delete outletfromgroup, optionally followed by an outlet name
and a group name. Press Enter, or
Type delete outletfromgroup, followed by all then the group name. Press Enter.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 31
Environmental Monitor Administration
Creating a descriptive Environmental Monitor name
The Set Envmon Name command assigns a descriptive name to the integrated Environmental Monitor.
This descriptive name is displayed when the Evnmon command is issued.
To create an Environmental Monitor name:
At the PDU: prompt, type set envmon name, followed by the absolute Environmental Monitor name,
then the descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126
decimal – spaces are not allowed). Press Enter.
Example
The following command adds the descriptive name Florida_HQ_1to the Environmental Monitor:
Switched PDU: set envmon name .a Florida_HQ_1<Enter>
Creating a descriptive temperature/humidity sensor name
The Set Envmon THS Name command assigns a descriptive name to a temperature/humidity sensor.
This descriptive name is displayed when the Evnmon command is issued.
To create an temperature/humidity sensor name:
At the PDU: prompt, type set envmon ths name, followed by the absolute name of the
temperature/humidity sensor, then the descriptive name of up to 24 alphanumeric and other typeable
characters (ASCII 33 to 126 decimal – spaces are not allowed). Press Enter.
Example
The following command adds the descriptive name T/H2_Florida_HQ_1 to the second
temperature/humidity sensor:
Switched PDU: set envmon ths name .a2 T/H2_Florida_HQ_1<Enter>
Serial Port Administration
Creating a descriptive serial port name
The Set Port Name command assigns a descriptive name to a serial port. You may use this name in
commands that require a port name as an alternative to using the port’s absolute name.
To create an port name:
At the Switched PDU: prompt, type set port name, followed by the absolute outlet name and a
descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal spaces are not allowed). Port names are not case sensitive. Press Enter.
Example
The following command adds the descriptive name Rack1 to Console port:
Switched PDU: set port name console Rack1<Enter>
Setting the serial ports data-rate
The Set Port Speed command sets the default data-rate for the serial port.
Valid data-rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200.
To set the serial port data-rate:
At the Switched PDU: prompt, type set port speed, follow by the data-rate and press Enter.
Example
The following command sets the serial ports data-rate to 38400 BPS:
Switched PDU: set port speed 38400<Enter>
Enabling or disabling active signal checking for serial connections
The Set Port Dsrchk command enables or disables active signal checking for serial connections to
devices attached to any of the available serial ports.
To enable or disable active signal checking for serial connections:
At the Switched PDU: prompt, type set port dsrchk console, on or off, and press Enter.
32 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Setting the serial port timeout value
The Set Port Timeout command is used to set the serial port inactivity timeout period. The timeout
period defines the maximum period of inactivity before automatically closing the Pass-Thru session.
The valid range for the period parameter is 0 to 5 (in minutes). The default period is 5.
NOTE: Setting the timeout to ‘0’ disables the timer.
To set the serial port timeout value:
At the PDU: prompt, type set port timeout, followed by a value from 0 to 5 (in minutes) and press
Enter.
Displaying serial port information
The Show Ports command displays information about all serial ports. This information includes:
•
•
•
Serial port data rate
Descriptive port name, if applicable
DSR signal checking settings
To display serial port information:
At the Switched PDU: prompt, type show ports and press Enter.
Example
The following command displays all serial port information:
Switched PDU: show ports<Enter>
Serial Port Configuration
ALL Ports:
Baud Rate: 38400
Port ID: Console
Connection Timeout: 5 minutes
Port Name: CONSOLE
DSR Check: ON
System Administration
Creating a location description
The Set Location command specifies text that appears in the HTML control screen’s Location field.
The text is also appended to a Welcome to banner that appears when a user successfully logs in serially
or through a Telnet session.
If you do not issue this command, or if you issue this command without specifying any text, the control
screen ’s Location field will be blank and no Welcome to banner will be displayed.
To create a location description:
At the Switched PDU: prompt, type set location, followed by a descriptive name of up to 24
alphanumeric and other typeable characters (ASCII 32 to 126 decimal - spaces are allowed). Press
Enter.
Omitting any characters after typing ‘set location’ deletes any previously specified text.
Examples
The following command specifies Florida HQ as the descriptive location for the control screen and the
login banner:
Switched PDU: set location Florida HQ<Enter>
The following command deletes any previously specified location description:
Switched PDU: set location<Enter>
In this case, the control screen’s Location field will be blank, and no welcome banner will be displayed
after a successful login.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 33
Setting the LED display orientation
The Set Display command is used to configure the Current LED(s) display orientation.
To set the LED display orientation:
At the Sentry: prompt, type set display, followed by normal or inverted and press Enter.
Example
The following set the LED display orientation to Inverted:
Sentry: set display inverted<Enter>
NOTE: When set to Inverted, the load will be reported in whole ampere increments
Displaying system configuration information
The Show System command displays all system configuration information.
•
•
•
•
•
Firmware version
NIC module serial number and MAC address
Hardware revision code and Flash size
Uptime since last system restart
System location description
See Chapter 4: Advanced Operations on page 41 for more information on SNMP.
To display system configuration information:
At the Switched PDU: prompt, type show system and press Enter.
Example
System Information
F/W Version:
NIC S/N:
MAC Address:
H/W Rev Code:
Flash Size:
Uptime:
Leviton Version 5.3b
1600001
00-0a-9c-10-00-01
0
2 MB
0 days 6 hours 14 minutes 1 second
Location:
Florida HQ
Creating a descriptive tower name
The Set Tower Name command assigns a descriptive name to a tower. This descriptive name is
displayed when the Show Traps command is issued. See Displaying trap configuration information on
page 35 for more information on the Show Traps command.
To create a tower name:
At the Switched PDU: prompt, type set tower name, followed by the absolute tower name, then the
descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal spaces are not allowed). Press Enter.
Example
The following command adds the descriptive name Florida_HQ_1 to tower .a:
Switched PDU: set tower name .a Florida_HQ_1<Enter>
Displaying tower information
The Show Towers command displays information about the PDU. This information includes the
absolute and descriptive PDU names.
To display tower information:
At the Switched PDU: prompt, type show towers and press Enter.
Example
Switched PDU: show towers<Enter>
Tower
ID
Tower
Name
.A
Florida_HQ_1
34 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Creating a descriptive infeed name
The Set Infeed Name command assigns a descriptive name to an infeed. This descriptive name is
displayed when the Show Traps command is issued. See Displaying trap configuration information on
page 35 for more information on the Show Traps command.
To create a infeed name:
At the Switched PDU: prompt, type set infeed name, followed by the absolute infeed name, then the
descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 33 to 126 decimal spaces are not allowed). Press Enter.
Example
The following command adds the descriptive name HQ_1_Infeed_A to the infeed on the Switched
PDU:
Switched PDU: set infeed name .aa HQ_1_Infeed_A<Enter>
Displaying Infeed information
The Show Infeeds command displays information about all infeeds. This information includes the
absolute and descriptive infeed names.
To display tower information:
At the Switched PDU: prompt, type show infeeds and press Enter.
Example
Switched PDU: show infeeds<Enter>
Input
Feed ID
Input
Feed Name
.AA
.AB
.BA
.BB
HQ_1_Infeed_A
HQ_1_Infeed_B
HQ_2_Infeed_A
HQ_2_Infeed_B
Displaying the Leviton firmware version
The Version command displays the Leviton firmware version.
To display the firmware version:
At the Switched PDU: prompt, type version and press Enter.
Performing a warm boot
The Restart command performs a warm boot of the PDU.
NOTE: System user/outlet/group/port configuration or outlet states are NOT changed or reset with this command.
To perform a warm boot:
At the Switched PDU: prompt, type restart and press Enter.
TCP/IP Administration
NOTE: A restart of the PDU is required after setting or changing ANY TCP/IP configurations. See Performing a warm
boot on page 35 for more information.
Setting the IP address
The Set Ipaddress command sets the TCP/IP address of the network interface controller.
To set the IP address:
At the Switched PDU: prompt, type set ipaddress, followed by the IP address and press Enter.
Example
The following command sets the IP address to 12.34.56.78:
Switched PDU: set ipaddress 12.34.56.78<Enter>
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 35
Setting the subnet mask
The Set Subnet command sets the subnet mask for the network the PT40 will be attached to.
To set the subnet mask:
At the Switched PDU: prompt, type set subnet, followed by the subnet mask and press Enter.
Example
The following command sets the subnet mask to 255.0.0.0
Switched PDU: set subnet 255.0.0.0<Enter>
Setting the gateway
The Set Gateway command sets the IP address of the default gateway the PDU uses to access external
networks.
To set the gateway IP address:
At the Switched PDU: prompt, type set gateway, followed by the gateway IP address and press Enter.
Example
The following command set the gateway IP address to 12.34.56.1:
Switched PDU: set gateway 12.34.56.1<Enter>
Setting the DNS IP address
The Set DNS command sets the TCP/IP address of the Domain Name server (DNS).
To set the DNS IP address:
At the Switched PDU: prompt, type set, followed by dns1 or dns2 and the Domain Name server’s IP
address. Press Enter.
Example
The following command sets the primary Domain Name server IP address to 98.76.54.254:
Switched PDU: set dns1 98.76.54.254<Enter>
Displaying network configuration information
The Show Network command displays TCP/IP, Telnet, SSH, Web, SSL and SNMP configuration information.
•
•
•
•
IP address, subnet mask, gateway and DNS IP addresses
Enabled-disabled status and port numbers for Telnet, SSH, HTTP,SSL and SNMP support
HTTP authentication method and SSL access setting
Network status
See Chapter 4: Advanced Operations on page 41 for more information on SNMP and Remote
Authentication
To display network configuration information:
At the Switched PDU: prompt, type show network and press Enter.
Example
The following command displays the network configuration information:
Switched PDU: show network<Enter>
Network Configuration
IP Address:
Subnet Mask:
Gateway:
12.34.56.78
255.0.0.0
12.34.56.1
Telnet:
SSH:
HTTP:
SSL:
SNMP:
Enabled
Enabled
Enabled
Enabled
Enabled
DNS1: 98.76.54.254
DNS2: 0.0.0.0
Port:
23
Port: 65535
Port:
80
Security: BASIC
Access:
Required
Network Status
Link:
Speed:
Duplex:
Negotiation:
36 • Operations
Up
100 Mbps
Full
Auto
Leviton Switched Power Distribution Unit
Installation and Operations Manual
HTTP Administration
NOTE: A restart is required after setting or changing ANY Telnet/Web configurations. See Performing a warm boot on
page 35 for more information.
Enabling and disabling HTTP support
The Set HTTP command is used to enable or disable HTTP support.
To enable or disable HTTP support:
At the Switched PDU: prompt, type set http, followed by enabled or disabled and press Enter.
Changing the HTTP server port
With HTTP support enabled, the HTTP server watches and responds to requests on the default HTTP port
number 80. This port number may be changed using the Set HTTP Port command.
To change the HTTP port:
At the Switched PDU: prompt, type set http port, followed by the port number and press Enter.
Example
The following changes the HTTP port number to 2048:
Switched PDU: set HTTP port 2048<Enter>
Setting the HTTP authentication method
The Set HTTP Security command is used to set the method of authentication. The PDU HTTP server supports
two authentication methods for security and validation of the username-password – Basic and MD5 digest.
For more information on authentication methods, see Setting the HTTP authentication method: on page 14.
To set the HTTP authentication method:
At the Switched PDU: prompt, type set http security, followed by basic or md5 and press Enter.
Telnet Administration
NOTE: A restart of the PDU is required after setting or changing ANY Telnet/Web configurations. See Performing a
warm boot on page 35 for more information.
Enabling and disabling Telnet support
The Set Telnet command is used to enable or disable Telnet support.
To enable or disable Telnet support:
At the Switched PDU: prompt, type set telnet, followed by enabled or disabled and press Enter.
Changing the Telnet port
With Telnet support enabled, the Telnet server watches and responds to requests on the default Telnet port
number 23. This port number may be changed using the Set Telnet Port command.
To change the Telnet socket:
At the Switched PDU: prompt, type set telnet port, followed by the port number and press Enter.
Example
The following changes the Telnet port number to 7001:
Switched PDU: set telnet port 7001<Enter>
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 37
FTP Administration
You may upload new versions of firmware into the PDU using File Transfer Protocol (FTP). This allows
access to new firmware releases for firmware improvements and new features additions. The following
commands are used to configure the PDU for an FTP firmware upload. See Appendix B: Uploading
Firmware for more information on initiating a FTP firmware upload.
Setting the FTP Host IP address
The Set FTP Host command sets the FTP host IP address allowing for firmware file uploads.
To set the FTP Host IP address:
At the Switched PDU: prompt, type set ftp host, followed by the Host IP address and press Enter.
Example
The following command sets the FTP Host IP address to 12.34.56.99:
Switched PDU: set ftp host 12.34.56.99<Enter>
Setting the FTP username
The FTP Username command sets the username as required by the FTP Host.
To set the FTP username:
At the Switched PDU: prompt, type set ftp username, followed by the FTP username and press Enter.
Example
The following command sets the FTP username to Guest:
Switched PDU: set ftp username guest<Enter>
Setting the FTP Password
The FTP Password command sets the password as required by the FTP Host.
To set the FTP password:
At the Switched PDU: prompt, type set ftp password, followed by the FTP password and press Enter.
Example
The following command sets the FTP password to OpenSesame:
Switched PDU: set ftp password OpenSesame<Enter>
Setting the filename to be uploaded
The FTP Filename command sets the filename of the firmware file to be uploaded.
To set the FTP filename:
At the Switched PDU: prompt, type set ftp filename, followed by the firmware filename and press Enter.
Example
The following command sets the FTP filename to snb_s53b.bin:
Switched PDU: set ftp filename snb_s53b.bin<Enter>
Setting the filepath for the file to be uploaded
The FTP Filepath command sets the filepath for the firmware file to be uploaded.
To set the FTP filepath:
At the Switched PDU: prompt, type set ftp filepath, followed by the filepath and press Enter.
Example
The following command sets the FTP filepath to ftp://Switched PDU:
Switched PDU: set ftp filepath ftp://Leviton<Enter>
38 • Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Displaying FTP configuration information
The Show FTP command displays all FTP configuration information.
•
•
•
FTP Host IP address
FTP Host username and password
Firmware filepath and filename
To display FTP configuration information:
At the Switched PDU: prompt, type show ftp and press Enter.
Example
The following command displays the FTP configuration information:
Switched PDU: show ftp<Enter>
FTP Configuration
Host IP Address:
Username:
Password:
Directory:
Filename:
12.34.56.99
guest
OpenSesame
ftp://Leviton
snb_s53b.bin
SNTP Administration
The PDU supports the use of a network time service to provide a synchronized time reference.
Setting the SNTP server address
The Set SNTP command is used to set the primary and secondary SNTP server addresses.
To set the SNTP server address:
At the Switched PDU: prompt, type set sntp, followed by primary or secondary, and the SNTP server
IP address. Press Enter.
Example
The following command set the primary SNTP server address to 204.152.184.72:
Switched PDU: set sntp primary 204.152.184.72<Enter>
Displaying SNTP configuration information
The Show SNTP command displays all SNTP configuration information.
To display SNTP configuration information
At the Switched PDU: prompt, type show sntp and press Enter.
Example
The following command displays the SNTP configuration information:
Switched PDU: show sntp <Enter>
SNTP Date/Time (GMT): 2003-02-21 21:32:48
SNTP Primary IP Address:
204.152.184.72
SNTP Secondary IP Address: 0.0.0.0
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Operations • 39
Chapter 4: Advanced Operations
SSL
Enabling and Setting up SSL Support
SSL Technical Specifications
42
42
42
SSH
Enabling and Setting up SSH Support
SSH Technical Specifications
43
43
43
SNMP
MIB, OID and Support
Enabling and Setting up SNMP Support
SNMP Traps
Configuring Traps
44
44
44
46
48
SSL
Secure Socket Layers (SSL) version 3 enables secure HTML sessions between a Leviton PDU Remote
Power Manager and a remote user. SSL provides two chief features designed to make TCP/IP
(Internet) transmitted data more secure:
•
•
Authentication – The connecting client is assured of the identity of the server.
Encryption – All data transmitted between the client and the server is encrypted rendering any
intercepted data unintelligible to any third party.
SSL uses the public-and-private key encryption system by RSA, which also requires the use of digital
certificates. An SSL Certificate is an electronic file uniquely identifying individuals or websites and
enables encrypted communication; SSL Certificates serve as a kind of digital passport or credential.
The Leviton PDU product’s SSL Certificate enables the client to verify the Leviton PDU’s authenticity
and to communicate with the Leviton PDU securely via an encrypted session, protecting confidential
information from interception and hacking.
SSL Command Summary
Command
Description
Set SSL
Enables/disables SSL support
Set SSL access
Sets SSL access as optional or required
Enabling and Setting up SSL Support
NOTE: A restart of the Leviton PDU is required after setting or changing ANY SSL configurations. See Performing a
warm boot on page 35 for more information.
Enabling or disabling SSL support
The Set SSL command is used to enable or disable SSL support.
To enable or disable SSL support:
At the Switched PDU: prompt, type set ssl, followed by enabled or disabled and press Enter.
Setting SSL access level
The Set SSL Access command is used to assign use of SSL as optional or required. The default access
level is set to optional.
To change the access level:
At the Switched PDU: prompt, type set ssl access, followed optional or required, and press Enter.
Example
The following changes the access level to required:
Switched PDU: set ssl access required<Enter>
SSL Technical Specifications
Secure Socket Layer (SSL) version 3
Transport Layer Security (TLS) version 1 (RFC 2246)
SSL/TLS-enabled HTTPS server (RFC 2818)
Self-Signed X.509 Certificate version 3 (RFC 2459)
Asymmetric Cryptography:
1024-bit RSA Key Exchange
Symmetric Cryptography Ciphers:
TLS_RSA_WITH_AES_256_CBC_SHA
TLS_RSA_WITH_AES_128_CBC_SHA
42 • Advanced Operations
TLS_RSA_WITH_3DES_EDE_CBC_SHA
TLS_RSA_WITH_DES_CBC_SHA
Leviton Switched Power Distribution Unit
Installation and Operations Manual
SSH
Secure Shell (SSH) version 2 enables secure network terminal sessions between a Leviton PDU Remote
Power Manager and a remote user over insecure network. SSH provides an encrypted terminal sessions
with strong authentication of both the server and client, using public-key cryptography and is typically
used as a replacement for unencrypted Telnet. In addition to enabling secure network terminal sessions
to the Leviton PDU for configuration and power management, the SSH session may be used for secure
Pass-Thru connections to attached devices.
SSH requires the configuration and use of a client agent on the client PC. There are many freeware,
shareware or for-purchase SSH clients available. Two examples are the freeware client PuTTY and the
for-purchase client SecureCRT® by VanDyke® Software. For configuration and use of these clients,
please refer to the applicable software documentation.
SSH Command Summary
Command
Description
Set SSH
Enables/disables SSH support
Set SSH port
Sets the SSH server port number
Enabling and Setting up SSH Support
NOTE: A restart of the Leviton PDU is required after setting or changing ANY SSH configurations. See Performing a
warm boot on page 35 for more information.
Enabling or disabling SSH support
The Set SSH command is used to enable or disable SSH support.
To enable or disable SSH support:
At the Switched PDU: prompt, type set ssh, followed by enabled or disabled and press Enter.
Changing the SSH server port
With SSH support enabled, the SSH server watches and responds to requests on the default SSH port
number 22. This port number may be changed using the Set SSH Port command.
To change the SSH port:
At the Switched PDU: prompt, type set ssh port, followed by the port number and press Enter.
Example
The following changes the SSH port number to 65535:
Switched PDU: set ssh port 65535<Enter>
SSH Technical Specifications
Secure Shell (SSH) version 2
Asymmetric Cryptography:
Diffie-Hellman DSA/DSS 512-1024 (random) bits per NIST specification
Symmetric Cryptography:
AES256-CBC
RIJNDAEL256-CBC
AES192-CBC
RIJNDAEL192-CBC
AES128-CBC
RIJNDAEL128-CBC
Message Integrity:
HMAC-SHA1-160
HMAC-MD5-128
3DES-192-CBC
BLOWFISH-128-CBC
ARCFOUR-128
HMAC-SHA1-96
HMAC-MD5-96
Authentication:
Username/Password
Session Channel Break Extension (for RS232 Break)
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Advanced Operations • 43
SNMP
The Leviton PDU family of products supports the Simple Network Management Protocol (SNMP).
This allows network management systems to use SNMP requests to retrieve information and control
power for the individual outlets.
The Leviton PDU includes an SNMP v2c agent supporting standard MIB I and MIB II objects. A
private enterprise MIB extension (Leviton3 MIB) is also supported to provide remote power control.
See SNMP on page 18, for information on enabling and configuring SNMP.
NOTE: For security, SNMP support is disabled by default.
SNMP Command Summary
Command
Description
Set snmp
Enables or disables SNMP support
Set snmp getcomm
Sets the ‘get’ community string
Set snmp setcomm
Sets the ‘set’ community string
Set snmp trapdest1
Sets a destination IP addresses for traps
Set snmp trapdest2
Sets a destination IP addresses for traps
Set snmp traptime
Sets the delay for steady state condition traps
Show snmp
Displays all SNMP configuration information
MIB, OID and Support
The Leviton SNMP MIB and OID are available on the Leviton website:
ftp://www.levitonvoicedata.com/levitonvoicedata.com/public/support/SNMP/
Technical Support is available from 6:30 AM to 4:30 PM, Monday-Friday, Pacific Time.
For SNMP Support, email: http://www.levitonvoicedata.com/support/contact.aspx
Enabling and Setting up SNMP Support
Leviton SNMP support must be enabled and configured for access to Leviton3 MIB objects and
generation of all Leviton3 traps.
Enabling/disabling SNMP support
The Leviton SNMP command is used to enable or disable SNMP support.
To enable SNMP support:
At the Switched PDU: prompt, type set snmp, followed by enabled or disabled and press Enter.
NOTE: A restart of the Leviton PDU is required after enabling or disabling SNMP support. See Performing a warm boot
on page 35 for more information.
Setting trap destinations
The Set SNMP Trapdest1 and Trapdest2 commands are used to set the IP addresses of SNMP
management stations receiving all traps. The Leviton PDU supports a maximum of two trap
destinations; one must be defined to enable trap generation.
To set the trap destination:
At the Switched PDU: prompt, type set snmp, trapdest1 or trapdest2, the Ipaddress and press Enter.
Example
The following sets the trap destination 1 to 64.42.31.208:
Switched PDU: set snmp trapdest1 64.42.31.208<Enter>
To reset the trap destination:
At the Switched PDU: prompt, type set snmp, trapdest1 or trapdest2, 0.0.0.0 and press Enter.
44 • Advanced Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Setting the trap timer
The Set Traptime command sets the timer period between repeated error-condition traps. The valid
range for the timer period is 1 to 65535 (in seconds).
The default value for the timer period is 60 seconds.
To set the trap timer:
At the Switched PDU: prompt, type set traptime, followed by the timer period and press Enter.
Example
The following sets the timer period to 180 seconds:
Switched PDU: set traptime 180<Enter>
Setting the Get/Set community strings
Leviton supports two SNMP community strings that provide varying levels of access to objects defined
in the Leviton3 MIB.
Community strings may be 1 to 24 characters.
Setcomm
The Setcomm string provides read-write access to Leviton3 MIB objects.
The default Setcomm string is “private”
To set the Setcomm community string:
At the Switched PDU: prompt, type set snmp setcomm, followed by the string and press Enter.
Getcomm
The Getcomm string provides read-only access to Leviton3 MIB objects.
The default Getcomm string is “public”.
To set the Getcomm community string:
At the Switched PDU: prompt, type set snmp getcomm, followed by the string and press Enter.
Setting the Trap community string
The Set SNMP Trapcomm command is used to set the community string that is included with all
generated traps. This string must be defined to enable trap generation.
The trap community string may be 1 to 24 characters.
The default Trapcomm string is “trap”.
To set the Trapcomm community string:
At the Switched PDU: prompt, type set snmp trapcomm, followed by the string and press Enter.
Displaying SNMP configuration information
The Show SNMP command displays all SNMP configuration information.
•
•
•
•
SNMP support status
SNMP community strings
Trap timer value
Trap destinations
To display SNMP configuration information:
At the Switched PDU: prompt, type show snmp and press Enter.
Example
The following command displays the SNMP configuration information:
Switched PDU: show snmp<Enter>
SNMP Configuration
SNMP:
SET Community String:
GET Community String:
TRAP Community String:
Error Trap Repeat Time (seconds):
Trap Destination 1:
Trap Destination 2:
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Enabled
private
public
trap
180
64.42.31.208
(undefined)
Advanced Operations • 45
SNMP Traps
The Switched PDU supports four types of SNMP traps. Traps are enabled at the Tower (T), Infeed (I),
outlet (O), Environmental Monitor (E) or sensor (S) level.
Trap Summary
Name
Level(s)
Status
T, I, O, E, S
Description
Operational status change
Change
O
Control status change
Load
I
Input load out of limit
Temp
S
Temperature is out of range
Humid
S
Relative Humidity is out of range
All traps include the Location of the Leviton PDU as defined with the Set Location command.
Status trap
A Status trap is generated when an error condition occurs on a tower, infeeed, Environmental Monitor
or individual sensor. Status traps include the reported Status, the Location of the Leviton PDU and
identifier and name of the affected tower, infeed, outlet, environmental monitor or sensor.
Any error state generates a Status trap and triggers the trap timer. A new trap is generated at the end of
every timer period until the Status returns to a non-error status. All status traps are enabled by default.
Tower Status traps
Status
Error
Normal
NoComm
Description
Tower is working correctly
x
Communication to the tower has been lost
Infeed Status traps
Status
Error
On
Description
Infeed is on
OffError
x
Infeed should be on but no current is sensed at the infeed
NoComm
x
Communication to the infeed has been lost
Outlet Status traps
Status
Error
On
Description
Outlet is on
Off
Outlet is off
OnWait
Outlet Status in transition
OffWait
Outlet Status in transition
OnError
x
Outlet should be off but current is sensed at the outlet
OffError
x
Outlet should be on but no current is sensed at the outlet
OffFuse
x
Outlet should be on but a blown fuse has been detected
NoComm
x
Communication to the outlet has been lost
Environmental Monitor Status traps
Status
Error
Normal
NoComm
Description
Environmental Monitor is working correctly
x
Communication to the Environmental Monitor has been lost
46 • Advanced Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Temperature/Humidity Sensor Status traps
Status
Error
Description
Found
The sensor has been detected
NotFound
No sensor has been detected
Lost
x
Sensor initially detected but communication to the sensor has been lost
NoComm
x
Communication to the sensor has been lost
NOTE: Traps are generated according to a hierarchical architecture; ie if an Tower Status enters a trap condition, only the
Tower Status trap will be generated. Infeed, Outlet, Environmental Monitor or Sensor Status and Temp and Humid traps
will be suppressed until the Tower Status returns to Normal.
Change trap
The Change trap is generated for all outlet status changes between any on/off conditions. Change traps
include the outlet status, Location of the Leviton PDU, and identifier and name of the affected outlet.
For descriptions of the outlet status types, please refer to the prior table.
Load Trap
The Load trap is generated whenever the total input load on an infeed exceeds a preset threshold. Load
traps include the reported input load, load status, Location of the Leviton PDU, and identifier and name
of the affected infeed.
Any error state generates a Load trap and triggers the trap timer. A new trap is generated at the end of
every timer period until the Load returns to a non-error status.
Load traps
Status
Error
Description
Normal
Infeed is on and within preset thresholds
NotOn
Infeed is off
Reading
Non-error state – Load status currently being read
LoadHigh
x
Infeed current load exceeds preset threshold
OverLoad
x
Infeed current load exceeds the measurable range for the infeed
ReadError
x
Unable to read Load status
NoComm
x
Communication to the infeed has been lost
Temp Trap
The Temp trap is generated whenever the temperature on a temperature/humidity sensor is beyond
preset thresholds. Temp traps include the reported temperature, temp status, Location of the Leviton,
and identifier and name of the affected sensor.
Any error state generates a Temp trap and triggers the trap timer. A new trap is generated at the end of
every timer period until the Temp returns to a non-error status.
Temp traps
Status
Error
Description
Normal
The sensor is working correctly and the temperature is within preset thresholds
NotFound
No sensor has been detected
Reading
Temp status currently being read
TempLow
x
Temperature at the sensor below preset low threshold
TempHigh
x
Temperature at the sensor exceeds preset high threshold
ReadError
x
Unable to read Temp status
Lost
x
Sensor initially detected but communication to the sensor has been lost
NoComm
x
Communication to the sensor has been lost
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Advanced Operations • 47
Humidity Trap
The Humidity trap is generated whenever the humidity on a temperature/humidity sensor is beyond
preset thresholds. Humidity traps include the reported relative humidity, humidity status, Location of
the Leviton PDU, and identifier and name of the affected sensor.
Any error state generates a Humidity trap and triggers the trap timer. A new trap is generated at the end
of every timer period until the Humidity returns to a non-error status.
Humidity traps
Status
Error
Normal
Description
The sensor is working correctly and the relative humidity is within preset thresholds
NotFound
No sensor has been detected
Reading
Humidity status currently being read
HumidLow
x
Relative humidity at the sensor below preset low threshold
HumidHigh
x
Relative humidity at the sensor exceeds preset high threshold
ReadError
x
Unable to read Humidity status
Lost
x
Sensor initially detected but communication to the sensor has been lost
NoComm
x
Communication to the sensor has been lost
Configuring Traps
SNMP Trap Command Summary
Command
Description
Set Trap Tower Status
Enables or disables the Tower Status trap
Set Trap Infeed Status
Enables or disables the Infeed Status trap off
Set Trap Infeed Load
Enables or disables the Infeed Load trap
Set Trap Infeed HighThresh
Sets the Infeed Load trap high limit
Set Trap Outlet Change
Enables or disables the Outlet Change trap
Set Trap Outlet Status
Enables or disables the Outlet Status trap
Set Trap EM Status
Enables or disables the Enivronmental Monitor Status trap
Set Trap THS Status
Enables or disables a temperature/humidity sensor Status trap
Set Trap THS Temp
Enables or disables a temperature/humidity sensor Temp trap
Set Trap THS Temphigh
Sets a temperature/humidity sensor Temp trap high limit
Set Trap THS Templow
Sets a temperature/humidity sensor Temp trap low limit
Set Trap THS Humid
Enables or disables a temperature/humidity sensor Humid trap
Set Trap THS Humidhigh
Sets a temperature/humidity sensor Humid trap high limit
Set Trap THS Humidlow
Sets a temperature/humidity sensor Humid trap low limit
Show Traps
Displays trap configurations
Enabling or Disabling a Status trap
The Set Trap … Status command is used to enable or disable Status traps for a Tower, Infeed or Outlet.
To Enable or Disable a Status trap:
At the Switched PDU: prompt, type set trap (tower, infeed, outlet, em or ths) status, followed by the
tower, infeed or outlet name, and on or off. Press Enter, or\
Type set trap (tower, infeed, outlet, em or ths) Status all, followed by on or off and press Enter.
Examples
The following command enables the Status trap for the first tower, using the tower’s absolute name:
Switched PDU: set trap tower status .a on<Enter>
The following command enables the Status trap for the tower named Florida_HQ_1:
Switched PDU: set trap tower status Florida_HQ_1 on<Enter>
NOTE: Enabling lower hierarchical traps automatically enables traps of higher hierarchical value: i.e. enabling an Outlet
Status trap automatically enables the Infeed and Tower Status traps for that outlet. Conversely, if a Tower Status trap is
disabled, all associated Infeed Status & Load and Outlet Status traps will be disabled.
48 • Advanced Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Enabling or Disabling a Load trap
The Set Trap Infeed Load command is used to enable or disable an Infeed Load trap.
To Enable or Disable a Load trap:
At the Switched PDU: prompt, type set trap infeed load, followed by the infeed name, and on or off. Press
Enter, or
Type set trap infeed load all, followed by on or off and press Enter.
Examples
The following command enables the Load trap for second infeed on the first tower, using the infeed’s
absolute name:
Switched PDU: set trap infeed load .AB on<Enter>
The following command disables the Load trap for all infeeds:
Switched PDU: set trap infeed load all off<Enter>
NOTE: Enabling lower hierarchical traps automatically enables traps of higher hierarchical value: i.e. enabling an Infeed
Load trap automatically enables the Infeed and Tower Status traps for that infeed.
Setting the Infeed Load limit
The Set Trap Infeed Loadhigh command is used to set the upper load limits for an input feed.
To set the infeed load limit:
At the Switched PDU: prompt, type set trap infeed loadhigh, followed by the infeed name, and a value
from 0 to 255 in amperes. Press Enter.
Example
The following command sets the infeed load limit for the second infeed on the first tower to 25
amperes, using the infeed’s absolute name:
Switched PDU: set trap infeed loadhigh .ab 25<Enter>
Enabling or Disabling a Change trap
The Set Trap Outlet Change command is used to enable or disable an Outlet Change trap.
To Enable or Disable a Change trap:
At the Switched PDU: prompt, type set trap outlet change, followed by the outlet name and on or off. Press
Enter, or
Type set trap outlet change all, followed by on or off and press Enter.
Example
The following command enables the Change trap for the third outlet on the first infeed of the second
tower, using the outlet’s absolute name:
Switched PDU: set trap outlet change .ba3 on<Enter>
Enabling or Disabling the Temp trap
The Set Trap THS Temp command is used to enable or disable the Temp trap.
To Enable or Disable the Temp trap:
At the Switched PDU: prompt, type set trap ths temp, followed by the sensor name and on or off.
Press Enter.
Example
The following command enables the Temp trap for the first temperature-humidity sensor:
Switched PDU: set trap ths temp .a1 on<Enter>
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Advanced Operations • 49
Setting the Temperature sensor threshold limits
The Set Trap THS Templow and Set Trap THS Temphigh commands are used to set the lower and
upper threshold limits for the Temperature sensor.
To set the Temperature threshold limits:
At the Switched PDU: prompt, type set trap ths, templow or temphigh, followed by the sensor name
and a value from 0 to 127 in degrees Celsius. Press Enter.
Example
The following command sets the second temperature high threshold limit to 95:
Switched PDU: set trap ths temphigh .a2 95<Enter>
Enabling or Disabling the Humid trap
The Set Trap THS Humid command is used to enable or disable the Humid trap.
To Enable or Disable the Humid trap:
At the Switched PDU: prompt, type set trap ths humid, followed by the sensor name and on or off.
Press Enter.
Example
The following command enables the Humid trap for the first temperature-humidity sensor:
Switched PDU: set traps ths humid .a1 on<Enter>
Setting the Humidity sensor threshold limits
The Set Trap THS Humidlow and Set Trap THS Humidhigh commands are used to set the lower and
upper threshold limits for the Humidity sensor.
To set the Humidity threshold limits:
At the Switched PDU: prompt, type set trap ths, humidlow or humidhigh, followed by the sensor
name and a value from 0 to 100 in percent relative humidity. Press Enter.
Example
The following command sets the first humidity sensor low threshold limit to 5:
Switched PDU: set trap ths humidlow .a1 5<Enter>
50 • Advanced Operations
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Displaying trap configuration information
The Show Traps command displays information about all traps.
To display trap information:
At the Switched PDU: prompt, type show traps and press Enter.
Example
The following command requests trap configuration information:
Switched PDU: show traps <Enter>
Tower trap configuration:
Tower
ID
Tower
Name
Status
Trap
.A
.B
Florida_HQ_1
Florida_HQ_2
ON
ON
More (Y/es N/o): y
Input feed trap configuration:
Input
Feed ID
Input
Feed Name
Status
Trap
Load
Trap
.AA
.BA
HQ_1_Infeed_A
HQ_2_Infeed_A
ON
ON
ON
ON
High
Thresh
255 A
255 A
More (Y/es N/o): y
Outlet trap configuration:
Outlet
ID
Outlet
Name
Change
Trap
Status
Trap
.AA1
.AA2
.AA3
.AA4
.AA5
.AA6
.AA7
.AA8
.AB1
.AB2
.AB3
.AB4
.AB5
.AB6
.AB7
.AB8
DataServer_1
WebServer_1
FileServer_1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
More (Y/es N/o): y
Environmental Monitor .A trap configuration:
Name: Florida_HQ_1
Status Trap: ON
Temperature/Humidity Sensor .A1
Name: Temp_Humid_Sensor_A1
Status Trap: ON
Temp Trap: ON
Low: 0
Deg.C
High: 127 Deg.C
Humid Trap: ON
Low: 5
% RH
High: 100 % RH
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Temperature/Humidity Sensor .A2
Name: T/H2_Florida_HQ_1
Status Trap: ON
Temp Trap: ON
Low: 0
Deg.C
High: 95 Deg.C
Humid Trap: ON
Low: 0
% RH
High: 100 % RH
Advanced Operations • 51
Chapter 5: Appendices
Appendix A: Resetting to Factory Defaults
You may reset the non-volatile RAM that stores all configurable options. This clears all administratoreditable fields and resets all command line configurable options to their default values, including all
user accounts.
You may reset the unit to factory defaults from the command line or the HTML interface, or by
pressing the reset button. You must have administrator-level privileges to issue the command. Using
the reset button may be necessary when a forgotten password prevents administrator login. Each of the
methods updates the current working configuration to the factory defaults.
NOTE: Resetting the unit resets all TCP/IP and Telnet/Web configurations. Reconfiguring the TCP/IP and Telnet/web
settings will be required.
To reset to factory defaults from the HTML interface
On the Restart page in the Tools section of the HTML interface, select Restart and reset to factory
defaults from the drop-down menu and press Apply.
To reset to factory defaults from the command line
At the Switched PDU: prompt, type restart factory and press Enter.
To reset to factory defaults using the reset button
Locate the recessed reset button directly beside the Serial & Ethernet ports. You will need a nonconductive, non-metallic tool that fits inside the recess.
Insert the tool in the recess, then depress and hold the reset button for at least ten seconds.
NOTE: If the reset button is depressed and held for more than 15 seconds, the reset will abort.
Appendix B: Uploading Firmware
You may upload new versions of firmware using File Transfer Protocol (FTP). This allows access to
new firmware releases for firmware improvements and new features additions.
NOTE: To begin an FTP upload session, you must first configure the FTP Host address, username/password, filename and
filepath. For information on configuring the FTP settings required for firmware upload see Chapter 3: Operations.
You may initiate an FTP upload session by issuing a command or from the HTML interface. You must
have administrator-level privileges to initiate an upload.
To initiate an FTP upload session from the HTML interface
On the Restart page in the Tools section of the HTML interface, select Restart and upload firmware
via FTP from the drop-down menu and press Apply.
Upon issuing this command the unit will restart and upload the firmware file specified with the FTP
Filename command from the previously configured FTP Host. See See FTP Administration in Chapter
3: for more information.
To initiate an FTP upload session from the command line
The Restart FTPLoad command initiates an upload of firmware. Upon issuing this command the unit
will restart and upload the firmware file specified with the FTP Filename command from the previously
configured FTP Host. See FTP Administration in Chapter 3: for more information.
To initiate an FTP firmware upload session:
At the Switched PDU: prompt, type restart ftpload and press Enter.
52 • Appendices
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Appendix C: Technical Specifications
Models
Switched PDU
Model
Rated Voltage
Input Cordset and Plug (10’)
SH081-1D1
SH081-1B1
SH082-1C2
SV161-1D1
SV161-1B1
SV162-1C2
100-120V 50/60Hz
100-120V 50/60Hz
208-240V 60Hz
100-120V 50/60Hz
100-120V 50/60Hz
208-240V 60Hz
IEC 60320 C20
NEMA L5-30P, 30A/120V locking
NEMA L6-30P, 30A/208V locking
1
IEC 60320 C20
NEMA L5-30P, 30A/120V locking
NEMA L6-30P, 30A/208V locking
Outlets
1
8 NEMA 5-20R
8 NEMA 5-20R
8 IEC 60320 C13
16 NEMA 5-20R
16 NEMA 5-20R
16 IEC 60320 C13
Expansion Module PDU
Model
Rated Voltage
Input Cordset and Plug (10’)
Outlets
1
EH081-1D1
100-120EV 50/60Hz
EH081-1B1
100-120EV 50/60Hz
EH082-1C2
208-240EV 60Hz
EV161-1D1
100-120EV 50/60Hz
EV161-1B1
100-120EV 50/60Hz
EV162-1C2
208-240EV 60Hz
1
Input cordset selected at time of purchase.
IEC 60320 C20
NEMA L5-30P, 30A/120EV locking
NEMA L6-30P, 30A/208EV locking
1
IEC 60320 C20
NEMA L5-30P, 30A/120EV locking
NEMA L6-30P, 30A/208EV locking
8 NEMA 5-20R
8 NEMA 5-20R
8 IEC 60320 C13
16 NEMA 5-20R
16 NEMA 5-20R
16 IEC 60320 C13
Power Ratings
Model
Input Current Ratings1
L'indice du courant d'entrée
Eingangsstromstärke
Voltage
Current
Modele
Modell
Tenson
Spannung
100-120V 50/60Hz
SH081-1D1
100-120V
EH081-1D1
50/60Hz
SH081-1B1
100-120V
EH081-1B1
50/60Hz
SV161-1D1
100-120V
EV161-1D1
50/60Hz
SV161-1B1
100-120V
EV161-1B1
50/60Hz
208-240V 60Hz
SH082-1C2
208-240V
EH082-1C2
60Hz
SV162-1C2
208-240V
EV162-1C2
60Hz
1
Courrant
Strom
16
24
16
24
24
24
Voltage
Tension
Spannung
100-120V
50/60Hz
100-120V
50/60Hz
100-120V
50/60Hz
100-120V
50/60Hz
208-240V
60Hz
208-240V
60Hz
Output Current Ratings
L'indice due courant de sortie
Ausgangsstromstärke
Outlet
Branch Circuit
Phase2
Total
Prise
Anschlussstelle
Circuit de la Branche
Zweigstromkreis
Total
Insgesamt
16
16
16
16
16
24
16
16
16
16
16
24
12
16
12
16
X
24
24
All current ratings are in amperes. Tous les indices de courant sont en ampères. Alle Angaben der Stromstärke erfolgen in Ampere.
Physical Specifications
Operating
Storage
Temperature
32° to 122° F (0° to 50° C)
-40° to 185° F (-40° to 85° C)
Elevation(above MSL)
0 to 10,000 ft (0 to 3000m)
0 to 50,000 ft (0 to 15000m)
Relative Humidity
10 to 90%, non-condensing
10 to 90%, non-condensing
Dimensions (H x W x D)
Weight
xH08x
xV16x
1.75 x 17.0 x 7.0 in.
45.75 x 1.75 x 2.25 in.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
(45 x 432 x 178 mm)
(1162 x 45 x 57 mm)
6.75 lbs
7.5 lbs
(3.1 kg)
(3.4 kg)
Appendices • 53
Branch Circuit Protection
Always disconnect both power supply cords before opening to avoid electrical shock.
Afin d’éviter les chocs électriques, débranchez les cables électrique avant d’ouvrir.
Immer beiden Netzleitungen auskuppeln vor den Aufmachen um elektrischen Schlag zu vermeiden.
Switched PDUs feature Branch Circuit protection on all outlets in the form of internal fuses. These
fuses meet the strict safety requirements of UL/CSA 60950-1 for Branch Circuit Protection.
Time-Delay Fuses – Class G
Amperes
Bussman Part Number
20
SC-20
CooperBussman product data-sheet #1024
Data Connections
RS-232 port
Switched PDUs are equipped standard with an RJ45 DTE RS-232c serial port. This connector may be
used for direct local access or from other serial devices such as a terminal server. An RJ45 crossover
cable is provided for connection to an RJ45 DCE serial port.
Pin
DTE Signal Name
Input/Output
1
Request to Send
RTS
Output
2
Data Terminal Ready DTR
Output
3
Transmit Data
TD
Output
4
Signal Ground
5
Signal Ground
6
Receive Data
RD
Input
7
Data Set Ready
DSR
Input
8
Clear to Send
CTS
Input
87654321
RJ45 to DB9F serial port adapter
Additionally, an RJ45 to DB9F serial port adapter is provided for use in conjunction with the RJ45
crossover cable to connect to a PC DB9M DCE serial port. The adapter pinouts below reflect use of the
adapter with the provided RJ45 crossover cable.
Pin
DCE Signal Name
Input/Output
1
2
Receive Data
RD
Output
3
Transmit Data
TD
4
Data Terminal Ready DTR
5
Signal Ground
6
Data Set Ready
DSR
Output
7
Request to Send
RTS
Input
8
Clear to Send
CTS
Output
Input
Input
5
4
9
3
8
2
7
1
6
LED Indicators
Units are equipped with a status LED for each power receptacle. A lit/on LED indicates that power is
being supplied at the port and a darkened/off LED indicates that there is no power at the port.
54 • Appendices
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Regulatory Compliance
Product Safety
Units have been safety tested and certified to the following standards:
•
USA/Canada
UL 60950:2003 and CAN/CSA 22.2 No. 60950-1-03
USA Notification
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Modifications not expressly approved by the manufacturer could void the user's authority to operated
the equipment under FCC rules.
Canadian Notification
This Class A digital apparatus complies meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigencies du Règlement sur le matériel
brouilleur du Canada.
Leviton Switched Power Distribution Unit
Installation and Operations Manual
Appendices • 55
Appendix D: Warranty and Support
Warranty
For a copy of Leviton’s product warranties, log on to www.levitonvoicedata.com/warranty.
Technical Support
Leviton understands that there are often questions when installing and/or using a new product. Free
Technical Support is provided from 6:00 AM to 4:30 PM, Monday-Friday, Pacific Time.
Leviton Voice & Data Division
2222 – 222nd Street SE
Bothell, WA 98021 USA
56 • Appendices
Tel: (800) 722.2082
Fax: 425.483.5270
Web: www.levitonvoicedata.com
Leviton Switched Power Distribution Unit
Installation and Operations Manual
2222 222nd St. SE
Bothell, WA 98021
+1.800.722.2082 Tel
+1.425.483.5270 Fax
www.levitonvoicedata.com
301-0113-2 Rev. A (071805)
OR-69070-00-00-01 © 2005 Leviton All rights reserved.
Download PDF
Similar pages