service manual - Tecnicosaurios

SERVICE MANUAL
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA’s
I Exploded Views
I Parts List
When servicing the deck
mechanism, refer to MK14 Deck
Mechanism Section.
Deck Mechanism Part No.:
N2466FT
20″ ANALOG/DIGITAL
PURE FLAT COLOR TV/DVD/VCR
CT202MW8
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first
use all precautions thoroughly so that neither his safety nor the safe
operation of the equipment will be jeopardized by the service method
selected.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
MAIN SECTION
20″ ANALOG/DIGITAL
PURE FLAT COLOR TV/DVD/VCR
CT202MW8
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA’s
I Exploded Views
I Parts List
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1
Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1
Preparation for Servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1
How to Initialize the TV/DVD/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1
Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1
Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1
System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1
IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1
Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1
Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1
Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1
Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1
SPECIFICATIONS
*ˆ Mode---------SP mode unless otherwise specified
* Test input terminal
<Except Tuner>--------Video input (1 Vp-p)
Audio input (-10 dB)
<Tuner>------------------Ant. input (80 dBµV) Video: 87.5%
Audio: 25 kHz dev. (1 kHz Sin)
< DEFLECTION >
Description
Condition
Unit
Nominal
Limit
Horizontal
%
90
±5
Vertical
%
90/88
±5
Horizontal
%
0
±18
Vertical
%
0
±10
---
kV
25.5
+3/-7
Condition
Unit
Nominal
Limit
Center
m/m
0
0.4
Corner
m/m
0
2.5
Side
m/m
0
1.5
2. Tint Control Range
---
deg
±30
>+23/<-23
3. Contrast Control Range
---
dB
6
2
Contrast: Max
ft-L
28
24
---
K
9200
---
1. Over Scan
2. Linearity
3. High Voltage
< VIDEO & CHROMA >
Description
1. Misconvergence
4. Brightness (100% White Full Field)
5. Color Temperature
< DVD >
Measurement at Loader PCB CN2-3pin, 4pin (Audio) and Loader PCB CN2-6pin, 8pin (Video)
Description
Condition
Unit
Nominal
Limit
1. Horizontal Resolution (TDV-540 TIT.2 CHP.16)
---
Line
350
330
2. Video S/N (TDV-540 TIT.2 CHP.6)
---
dB
60
55
AM
---
dB
58
53
PM
---
dB
58
53
L
R
%
0.03
0.07
L, 20 Hz
R, 20 Hz
L, 20 kHz
R, 20 kHz
dB
0
+4/-5
L
R
dB
85
75
3. S/N Chroma
(TDV-540 TIT.2 CHP.17)
4. Audio Distortion (LPCM 48 kHz, W/LPF)
(PTD 1-NOR TIT.1 CHP.1)
5. Audio freq. Response (LPCM 48 kHz)
(PTD 1-NOR TIT.1 CHP.1, 5, 10)
6. Audio S/N (LPCM 48 kHz,W/LPF,A-WTD)
(PTD 1-NOR TIT.1 CHP.1, 2)
1-1-1
P7752SP
< TUNER >
Measurement at Speaker (Audio), TP1401 (Video)
Description
Condition
Unit
Nominal
Limit
1. Video S/N (80 dBµV, TV4ch)
---
dB
45
40
2. Audio S/N (W/LPF, 15 kHz dev.)
---
dB
45
40
Condition
Unit
Nominal
Limit
1. Horizontal Resolution
(R/P, SP)
Line
230
200
2. Jitter (Low)
(R/P, SP)
µs
0.1
0.2
AM
(R/P, SP)
dB
38
33
PM
(R/P, SP)
dB
38
33
(R/P, SP)
%
0.25
0.5
< VCR >
Measurement at TP1401 (Video)
Description
3. S/N Chroma
4. Wow & Fiutter (JIS, UNWTD)
< VCR NORMAL AUDIO>
All items are measured across 8 Ω resistor at speaker output terminal.
Description
Condition
Unit
Nominal
Limit
1. Audio Output Power
(R/P, SP)
W
1.0
0.8
2. Audio S/N (W/LPF)
(R/P, SP)
dB
40
36
3. Audio distortion (W/LPF, -10 dB 1 kHz IN)
(R/P, SP)
%
3.0
5.0
200 Hz
(R/P, SP)
dB
-2.0
-2.0±5.0
8 kHz
(R/P, SP)
dB
0
0±6.0
Condition
Unit
Nominal
Limit
1. Output Level (-10 dB 1 kHz IN)
(R/P, SP)
dB
-8.0
-8±4
2. Audio Distortion (-10 dB 1 kHz IN)
(R/P, SP)
%
0.5
1.0
20 Hz
(R/P, SP)
dB
0
±4
20 kHz
(R/P, SP)
dB
0
±4
4. Audio Freq. Response (-20dB 1kHz IN)
< VCR Hi-Fi AUDIO >
Description
3. Freq. Response (-15 dB 1 kHz IN)
1-1-2
P7752SP
< ATSC >
Measurement at Speaker (Audio)
Description
1. RECEIVED FREQ. RANGE
(-28dBm)
Condition
Unit
Nominal
Limit
+
kHz
150
>100
–
kHz
150
>100
dBµV
dBµV
dBµV
26/114
26/114
28/118
32/108
32/108
34/112
dB
dB
dB
20
20
20
<26
<26
<26
dB
dB
dB
0
0
0
>-6
>-6
>-6
A
dB
0
<6
B
dB
0
<6
C
dB
0
<6
D
dB
0
<6
E
dB
0
<6
F
dB
0
<6
FF
dB
0
<6
G
dB
0
<6
L
dB
60
>50
R
dB
60
>50
L
%
0.1
<3
R
%
0.1
<3
2. ATSC DYNAMIC RANGE (min./max.)
VHF LOW BAND. CH.4
VHF HI BAND. CH.10
UHF BAND. CH.41
---
3. ATSC SUSCEPTIBILITY TO
RANDOM NOISE
VHF LOW BAND. CH.4
VHF HI BAND. CH.10
UHF BAND. CH.41
---
4. NTSC CO-CHANNEL INTERFERENCE
VHF LOW BAND. CH.4
VHF HI BAND. CH.10
UHF BAND. CH.41
---
5. MULTIPATH
6. Audio S/N (0dBfs)
7. Audio DIST. (0dBfs)
Note: Nominal specifications represent the design specifications. All units should be able to approximate these.
Some will exceed and some may drop slightly below these specifications. Limit specifications represent
the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet
limit specifications.
1-1-3
P7752SP
LASER BEAM SAFETY PRECAUTIONS
This DVD player uses a pickup that emits a laser beam.
Do not look directly at the laser beam coming
from the pickup or allow it to strike against your
skin.
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep
your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser
beam.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.
Drive Mechanism
Assembly
Laser Beam Radiation
Laser Pickup
Turntable
CAUTION
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
Location: Top of DVD mechanism.
1-2-1
E7NLSP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for TV Circuit
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
1. Before returning an instrument to the
customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
b. Be sure that there are no cabinet openings
through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the picture tube
and the cabinet mask, (2) excessively wide
cabinet ventilation slots, and (3) an improperly
fitted and/or incorrectly secured cabinet back
cover.
LEAKAGE
CURRENT
TESTER
_
+
TEST ALL EXPOSED
METAL SURFACES
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE
LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
e. X-Radiation and High Voltage Limits Because the picture tube is the primary
potential source of X-radiation in solid-state TV
receivers, it is specially constructed to prohibit
X-radiation emissions. For continued Xradiation protection, the replacement picture
tube must be the same type as the original.
d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
1-3-1
TVDVDN_ISP
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
Also, because the picture tube shields and
mounting hardware perform an X-radiation
protection function, they must be correctly in
place. High voltage must be measured each
time servicing is performed that involves B+,
horizontal deflection or high voltage. Correct
operation of the X-radiation protection circuits
also must be reconfirmed each time they are
serviced. (X-radiation protection circuits also
may be called “horizontal disable” or “hold
down.”) Read and apply the high voltage limits
and, if the chassis is so equipped, the Xradiation protection circuit specifications given
on instrument labels and in the Product Safety
& X-Radiation Warning note on the service
data chassis schematic. High voltage is
maintained within specified limits by close
tolerance safety-related components/
adjustments in the high-voltage circuit. If high
voltage exceeds specified limits, check each
component specified on the chassis schematic
and take corrective action.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on
the receiver chassis, or on the picture tube.
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
4. Picture Tube Implosion Protection Warning The picture tube in this receiver employs integral
implosion protection. For continued implosion
protection, replace the picture tube only with one
of the same type number. Do not remove, install,
or otherwise handle the picture tube in any
manner without first putting on shatterproof
goggles equipped with side shields. People not so
equipped must be kept safely away while picture
tubes are handled. Keep the picture tube away
from your body. Do not handle the picture tube by
its neck. Some “in-line” picture tubes are equipped
with a permanently attached deflection yoke;
because of potential hazard, do not try to remove
such “permanently attached” yokes from the
picture tube.
5. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
6. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
7. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
8. Product Safety Notice - Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
1-3-2
TVDVDN_ISP
2) Strip about 15 mm of the insulation from the
ends of the wires. If the wires are stranded,
twist the strands to avoid frayed conductors.
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
3) Align the lengths of the wires to be connected.
Insert the wires fully into the connector.
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
4) Use the crimping tool to crimp the metal sleeve
at the center position. Be sure to crimp fully to
the complete closure of the tool.
L. When connecting or disconnecting the DVD/VCR
connectors, first, disconnect the AC plug from the
AC supply socket.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I.
Also check areas surrounding repaired locations.
J. Be careful that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. Crimp type wire connector
When replacing the power transformer in sets
where the connections between the power cord
and power transformer primary lead wires are
performed using crimp type connectors, in order to
prevent shock hazards, perform carefully and
precisely the following steps.
Replacement procedure
1) Remove the old connector by cutting the wires
at a point close to the connector.
Important: Do not re-use a connector (discard
it).
1-3-3
TVDVDN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Chassis or Secondary Conductor
Primary Circuit
Table 1: Ratings for selected area
AC Line Voltage
Region
Clearance
Distance (d), (d’)
110 to 130 V
U.S.A. or
Canada
≥ 3.2 mm
(0.126 inches)
d'
d
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
Fig. 1
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.).
Exposed Accessible Part
Z
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
AC Voltmeter
(High Impedance)
B
Earth Ground
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
U.S.A. or
Canada
0.15 µF CAP. & 1.5 kΩ
RES. Connected in parallel
i ≤ 0.5 mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
1-3-4
TVDVDN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications
Pb (Lead) Free Solder
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
Pb free mark will be found on PCBs which use Pb
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
Top View
Out
Bottom View
In
Input
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
5
Pb free mark
Pin 1
How to Remove / Install Flat Pack-IC
10
3. The 1st pin of every male connector is indicated as
shown.
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Pin 1
Instructions for Connectors
1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect
the AC cord.
2. FFC (Flexible Foil Connector) cable should be
inserted parallel into the connector, not at an
angle.
Fig. S-1-1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
FFC Cable
Connector
CBA
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
CAUTION:
* Be careful to avoid a short circuit.
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
1-4-1
TVDVDN_SN
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Flat Pack-IC
CBA
Desoldering Braid
Hot-air
Flat Pack-IC
Desoldering
Machine
Soldering Iron
Fig. S-1-3
Masking
Tape
Tweezers
Flat Pack-IC
Fig. S-1-2
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
1-4-2
TVDVDN_SN
With Iron Wire:
2. Installation
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
2. The “●” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
presolder the four corners of the flat pack-IC. (See
Fig. S-1-8.)
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower
or
Fig. S-1-7
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
CBA
Fig. S-1-8
Fine Tip
Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
1-4-3
TVDVDN_SN
Instructions for Handling Semiconductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct>
Grounding Band
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
1-4-4
TVDVDN_SN
PREPARATION FOR SERVICING
How to Enter Service Mode
Key
Caution 1:
Adjustment Mode
5
1. Optical sensors system are used for Tape Start
and End Sensor on this equipment. Read this
page carefully and prepare as described on this
page before starting to service; otherwise, the unit
may operate unexpectedly.
Head switching position adjustment:
See adjustment instructions.
6
YUV Brightness up adjustment mode in
DTV mode:
See adjustment instructions.
Preparing 1:
7
Purity check mode:
Shows Red, Green, Blue or White
cyclically on the screen each time the
[7] button is pressed.
8
H. Position adjustment:
See adjustment instructions.
9
V. Position/V. Size adjustment:
See adjustment instructions.
1. Cover Q1202 (START SENSOR) and Q1201
(END SENSOR) with Insulation Tape or enter the
service mode to activate Sensor Inhibition
automatically.
Note: Avoid playing, rewinding or fast forwarding the
tape to its beginning or end, because both
Tape End Sensors are not active.
VOL m
No need to use.
VOL n
Cut-off/Drive adjustment:
See adjustment instructions.
White balance adjustment:
See adjustment instructions.
How to Enter the Service Mode
1. Turn the power on.
2. Use the service remote control unit and press
[DISC MENU] button.
3. When entering the service mode, one of the
number (1, 2 or 4) will be displayed at corners of
the screen.
4. During Service mode, electrical adjustment mode
can be selected by the service remote control unit
key.
Details are as follows.
Key
Adjustment Mode
Picture adjustment mode in TV mode or
DTV mode:
Press the [PICTURE] button to change
from BRT (Bright), *CNT (Contrast),
PICTURE *COL (Color), *TNT(Tint), *V-T(V-Tint)
and *SHP (Sharpness). Press [CH. o/
p] buttons to display Initial Value.
*Marked items are not necessary to
adjust normally.
0
C-Trap adjustment mode in TV mode:
See adjustment instructions.
1
No need to use.
2
H f0 adjustment mode:
See adjustment instructions.
3
U-/V-Pedestal adjustment mode in DTV
mode:
See adjustment instructions.
4
Auto record mode:
Perform recording (15 Sec.) --> Stop -->
Rewind (Zero return) automatically.
Caution 2:
1. The deck mechanism assembly is mounted on the
Main CBA directly, and SW1211 (REC-SAFETY
SW) is mounted on the Main CBA. When deck
mechanism assembly is removed from the Main
CBA due to servicing, this switch can not be
operated automatically.
Preparing 2:
1. To eject the tape, press the [STOP/EJECT] button
on the unit (or remote control).
2. When you want to record during Service mode,
press the [REC] button while depressing SW1211
(REC-SAFETY SW) on the Main CBA.
Q1201
(END SENSOR)
SW1211
(REC-SAFETY SW)
1-5-1
Q1202
(START SENSOR)
MAIN CBA
P7753PFS
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
Removal
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
Step/
Loc.
No.
Part
[2] Tray Chassis Unit
[7] Function CBA
[4] DVD
Mechanism
DTV
[10] Module
CBA Unit
D2 *CN1101, *CN1102
D5 Module PCB Holder
---
↓
(1)
↓
(3)
↓
(5)
[9] Main CBA
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(3) Fig. No. showing procedure of part location
2. Disassembly Method
Removal
Part
↓
(4)
(2) Parts to be removed or installed.
[10] DTV Module
CBA Unit
[6] Sub CBA
Step/
Loc.
No.
↓
(2)
Note:
[3] CRT
[8] Deck Assembly
[5] DVD Main
CBA Unit
Note
---
Main CBA
CAUTION!
[1] Rear Cabinet
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
D2
4(S-12)
D5
[9]
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
Fig.
No.
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
4(S-1), (S-2), (S-3A),
(S-3B)
Note
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following “Reference Notes in the
Table”.
[1]
Rear
Cabinet
D1
[2]
Tray
Chassis
Unit
Anode Cap, *CN2501,
D2
CRT CBA, *CN1601,
D3
*CN2571, *CN3801,
D5
*CN3802
1
[3]
CRT
D3 4(S-4)
---
[4]
D2
DVD
4(S-5), *CN201,
D4
Mechanism
*CN301
D5
[5]
DVD Main
CBA Unit
D2
D4 *CN1, *CN2
D5
---
[6]
Sub CBA
D2 6(S-6), *CN1103,
D5 *CN1301, *CN1302
---
[7]
Function
CBA
D2
(S-7), *CN2401
D5
---
[8]
Deck
Assembly
3(S-8), Top Shield,
D2 7(S-9), (S-10), (S-11),
D5 *CL1201, *CL1401,
*CL1402, *CL1403
4
---
2, 3
1-6-1
P7752DC
Reference Notes in the Table
To avoid damage of pickup follow the next
procedures.
CAUTION!
1) Disconnect Connector (CN301) on the DVD
Main CBA Unit.
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
2) Short the three short lands of the FPC cable
with solder before removing the FFC cable
(CN201). If you disconnect the FFC cable
(CN201) without shorting them, the laser diode
of pickup will be destroyed. (Fig. D4)
1. CAUTION 1: Discharge the Anode Lead of the
CRT with the CRT Ground Wire before removing
the Anode Cap.
Disconnect the following: Anode Cap, CN2501,
CRT CBA, CN1601, CN2571, CN3801 and
CN3802. Then remove Tray Chassis Unit.
2. CAUTION 2: Electrostatic breakdown of the laser
diode in the optical system block may occur as a
potential difference caused by electrostatic charge
accumulated on cloth, human body etc., during
unpacking or repair work.
3) Remove DVD Mechanism.
3. CAUTION 3: When reassembling, confirm the
FFC cable (CN201) is connected completely. Then
remove the solder from the three short lands of the
FPC cable. (Fig. D4)
4. Remove screws 3(S-8) and remove Top Shield.
Remove screws 7(S-9), (S-10) and (S-11). Then,
desolder connectors (CL1201, CL1401, CL1402,
CL1403) and lift up the Deck Assembly.
(S-1)
(S-1)
(S-2)
(S-1)
(S-3A)
(S-3B)
(S-1)
[1] Rear Cabinet
Fig. D1
1-6-2
P7752DC
[2] Tray Chassis Unit
(S-8)
(S-5)
Top Shield
(S-5)
[4] DVD
Mechanism
(S-8)
(S-9)
(S-9)
(S-9)
(S-6)
(S-12)
(S-12)
(S-6)
(S-7)
Module PCB Holder
[5] DVD Main [8] Deck
CBA Unit
Assembly
[10] DTV
Module
CBA Unit
(S-6)
[6] Sub CBA
[7] Function
CBA
[9] Main CBA
(S-10)
(S-12)
(S-11)
Fig. D2
1-6-3
P7752DC
Anode Cap
(S-4)
CRT CBA
(S-4)
(S-4)
[3] CRT
(S-4)
Fig. D3
A
DVD Mechanism
Short the three short lands by soldering.
(Either of two places.)
FPC Cable
View for A
Fig. D4
1-6-4
P7752DC
DVD Main CBA Unit
CN301
Junction-B
CBA
CN201
TO SPEAKER
CN2A CN1A
CL3801
CN3801
ANODE
CRT
CN2801
GND
CN2571
Function
CBA
CL2501A
Sub CBA
FOCUS
SCREEN
CN2401
CN2
CN1 CL2504A
CN2301 CN2302 CN2103
Main CBA
CL1403
CN1104
CL2504B
CN1301 CN1302 CN1103
CRT CBA
CN2501
CL1401
CL2501B
AC CORD
CL1402
CN1601
CN1802
ACE HEAD
ASSEMBLY
CN3802
CL3802
CL1201
TUNER
CN1102 CN1101
CN102 CN101
TO SPEAKER
DTV Module CBA Unit
Junction-A CBA
FE HEAD
Deck Assembly
CYLINDER
ASSEMBLY
CAPSTAN
MOTOR
Fig. D5
1-6-5
P7752DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
Test Equipment Required
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
2. AC Milli Voltmeter (RMS)
How to enter Service mode:
Service mode:
1. Use the service remote control unit.
2. Turn the power on. (Use main power on the TV
unit.)
3. To change TV mode, DTV mode, or DVD mode,
press [SELECT] button on the TV unit.
4. Press [DISC MENU] button on the service remote
control unit.
X-Ray Protection Test
X-Ray protection test should be done when replacing
any parts of this chassis.
1. Short both ends of R2592 (on Sub CBA).
3. Alignment Tape (FL8A, FL8N), Blank Tape
2. Confirm that the main power turns off.
4. DC Voltmeter
3. If the main power does not turn off, then replace
the following parts (D2591, Q2591, R2592,
R2593, R2594 and IC1201).
5. Oscilloscope: Dual-trace with 10:1 probe,
V-Range: 0.001~50 V/Div,
F-Range: DC~AC-60 MHz
4. Perform steps 1 to 3 again.
6. Frequency Counter
7. Plastic Tip Driver
1. DC 114V (+B) Adjustment
8. Color Analyzer
Purpose: To obtain correct operation.
How to make the service remote
control unit:
Symptom of Misadjustment: The picture is dark and
the unit does not operate correctly.
1. Prepare normal remote control unit (Part No.
NE204UD or NE209UD). Remove 4 screws from
the back lid (Fig. 1).
Screws
Test Point
Adj. Point
Mode
Input
TP2501(+B)
TP2504(GND)
VR1601
---
---
Tape
M. EQ.
Spec.
---
DC Voltmeter
+114±1.0 V DC
Note: TP2501(+B), TP2504(GND) --- Sub CBA,
VR1601 --- Main CBA
Remote control unit (bottom)
Fig. 1
2. Cut off pin 10 of the remote control
microprocessor and short circuit pins 10 and 17 of
the microprocessor with a jumper wire.
1. Connect the unit to AC Power Outlet.
2. Connect DC Voltmeter to TP2501(+B) and
TP2504(GND).
3. Adjust VR1601 so that the voltage of TP2501(+B)
becomes +114±1.0 V DC.
1-7-1
P7753EA
2. Setting for CONTRAST, COLOR,
TINT, V-TINT and SHARPNESS
Data Values
YC-COLOR (YC-COL)
1. Press [2] button to select “YC-COLOR (YC-COL)”
display.
<TV mode (Composite block)>
2. Press [CH. o/p] buttons so that the value of “YCCOLOR (YC-COL)” becomes “70”.
1. Enter Service mode in TV mode.
YC-TINT (YC-TNT)
2. Press [PICTURE] button on the service remote
control unit. Display changes “BRT,” “CNT,” “COL,”
“TNT,” “V-T,” and “SHP” cyclically when [1] button is
pressed.
1. Press [2] button to select “YC-TINT (YC-TNT)”
display.
CONTRAST (CNT)
YC-SHARPNESS (YC-SHP)
1. Press [1] button to selcet “CONTRAST (CNT)”
display.
1. Press [2] button to select “YC-SHARPNESS (YCSHP)” display.
2. Press [CH. o/p] buttons so that the value of
“CONTRAST (CNT)” becomes “80”.
2. Press [CH. o/p] buttons so that the value of “YCSHARPNESS (YC-SHP)” becomes “37”.
2. Press [CH. o/p] buttons so that the value of “YCTINT (YC-TNT)” becomes “50”.
COLOR (COL)
1. Press [1] button to select “COLOR (COL)” display.
2. Press [CH. o/p] buttons so that the value of
“COLOR (COL)” becomes “58”.
TINT (TNT)
1. Press [1] button to select “TINT (TNT)” display.
2. Press [CH. o/p] buttons so that the value of
“TINT (TNT)” becomes “56”.
<DTV mode (YUV block)>
1. Enter Service mode in DTV mode.
2. Press [PICTURE] button on the service remote
control unit. Display changes “YUV-BRT,” “YUVCNT,” “YUV-COL,” “YUV-TNT,” and “YUV-SHP”
cyclically when [3] button is pressed.
YUV-CONTRAST (YUV-CNT)
1. Press [1] button to select “V-TINT (V-T)” display.
1. Press [3] button to selcet “YUV-CONTRAST (YUVCNT)” display.
2. Press [CH. o/p] buttons so that the value of “VTINT (V-T)” becomes “50”.
2. Press [CH. o/p] buttons so that the value of
“YUV-CONTRAST (YUV-CNT)” becomes “80”.
SHARPNESS (SHP)
YUV-COLOR (YUV-COL)
1. Press [1] button to select “SHARPNESS (SHP)”
display.
1. Press [3] button to select “YUV-COLOR (YUVCOL)” display.
2. Press [CH. o/p] buttons so that the value of
“SHARPNESS (SHP)” becomes “43”.
2. Press [CH. o/p] buttons so that the value of
“YUV-COLOR (YUV-COL)” becomes “58”.
Note: BRIGHT data value does not need to be
adjusted because this setting is performed in
other setting.
YUV-TINT (YUV-TNT)
V-TINT (V-T)
<DVD mode (Y-C block)>
1. Press [3] button to select “YUV-TINT (YUV-TNT)”
display.
2. Press [CH. o/p] buttons so that the value of
“YUV-TINT (YUV-TNT)” becomes “64”.
1. Enter Service mode in DVD mode.
YUV-SHARPNESS (YUV-SHP)
2. Press [PICTURE] button on the service remote
control unit. Display changes “YC-BRT,” “YC-CNT,”
“YC-COL,” “YC-TNT,” and “YC-SHP” cyclically
when [2] button is pressed.
1. Press [3] button to select “YUV-SHARPNESS
(YUV-SHP)” display.
2. Press [CH. o/p] buttons so that the value of
“YUV-SHARPNESS (YUV-SHP)” becomes “45”.
YC-CONTRAST (YC-CNT)
1. Press [2] button to selcet “YC-CONTRAST (YCCNT)” display.
2. Press [CH. o/p] buttons so that the value of “YCCONTRAST (YC-CNT)” becomes “75”.
1-7-2
P7753EA
3. C-Trap Adjustment
4. H f0 Adjustment
Purpose: To get minimum leakage of the color signal
carrier.
Purpose: To get correct horizontal position and size of
screen image.
Symptom of Misadjustment: If C-Trap Adjustment is
incorrect, stripes will appear on the screen.
Symptom of Misadjustment: Horizontal position and
size of screen image may not be properly displayed.
Test Point
Adj. Point
Mode
Input
TP1301
(BLUE)
[CH o / p]
buttons
---
Color Bar
Tape
M. EQ.
Spec.
---
Oscilloscope
Pattern Generator
---
Test Point
Adj. Point
Mode
Input
R2583
[CH. o / p] buttons
Video
---
Tape
M. EQ.
---
Spec.
Frequency Counter 15.734 kHz±300 Hz
Note: R2583 --- Sub CBA
1. Connect frequency counter to R2583 and ground.
Figure
2. Operate the unit for at least 20 minutes.
3. Enter the Service mode in TV mode.
minimum
4. Press [2] button on the service remote control unit
and select H-ADJ mode.
5. Press [CH. o/p] buttons on the service remote
control unit so that the display will change “0” to
“7.”
Fig. 2
Note: TP1301(BLUE) --- Sub CBA
6. At this moment, choose display “0” to “7” when the
frequency counter display is closest to 15.734 kHz
±300 Hz.
1. Connect oscilloscope to TP1301.
2. Input a color bar signal from RF input.
Enter Service mode.
3. Enter the Service mode in TV mode.
4. Press [0] button on the service remote control unit
and select C-TRAP mode. (Display changes “CTRP,” “D-T TV,” “D-T EXT,” “Y SW,” “B-S,” “BS2,”
and “C-ANG” cyclically when [0] button is
pressed.)
5. Press [CH o / p] buttons on the remote control
unit so that the carrier leakage B-Out (3.58 MHz)
value becomes minimum on the oscilloscope.
1-7-3
P7753EA
5. Cut-off/Drive Adjustment
to step 7 when the Green Cut off adjustment is
done.
Purpose: To adjust the beam current of R, G, B, and
screen voltage.
Symptom of Misadjustment: White color may be
reddish, greenish or bluish.
Test Point
Adj. Point
Mode
Input
---
Screen-Control
[CH. o / p]
buttons
RF
Black
Raster
Tape
M. EQ.
Spec.
---
Pattern
Generator
See Reference
Notes below.
Figure
7. Press [3] button on the service remote control unit
and select "COB" mode. The display will
momentarily show "COB". Adjust the Blue cut off
by pressing the "[CH. o / p]" buttons. When done
with steps 5, 6 and 7 the horizontal line should be
pure white, If not, then attempt the Cut off
adjustment again.
6. White Balance Adjustment
Purpose: To mix red, green and blue beams correctly
for pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
Pattern Generator
Test Point
Adj. Point
Mode
Input
Screen
[CH. o/p]
buttons
RF
White Raster
(APL 100%)
Tape
M. EQ.
Spec.
---
Pattern
Generator,
Color analyzer
See below
Figure
RF Input
Fig. 2
Note: Screen Control FBT --- Sub CBA
FBT = Fly Back Transformer
Use the service remote control unit
Color Analyzer
1. Degauss the CRT and allow the unit to operate for
20 minutes before starting the alignment.
2. Input the Black raster signal from RF input.
3. Enter the Service mode in TV mode.
4. Press [VOL n] button on the service remote
control to enter "C/D" mode. (Display changes "C/
D," "7f," "TUNER," "SLP R," "MONO," "DTV-H/-H2,"
"RATING," "RC5" "DL V-CHIP," and "D-SOUND"
cyclically when [VOL n] button is pressed.)
5. Press [1] button on the service remote control unit
and select "COR" mode.The display will
momentarily show "COR". Now there should be a
horizontal line across the center of the picture
tube. If needed, turn the screen control on the
flyback in a clockwise direction gradually until the
horizontal line appears. Adjust the Red Cut off by
pressing the "[CH. o / p]" buttons. Proceed to
Step 6 when the Red Cut off adjustment is done.
6. Press [2] button on the service remote control unit
and select "COG" mode. The display will
momentarily show "COG". Adjust the Green Cut
off by pressing the "[CH. o / p]" buttons. Proceed
Fig. 3
Note: Use the service remote control unit
1. Operate the unit more than 20 minutes.
2. Face the unit to the east. Degauss the CRT using
a degaussing coil.
3. Input the White Raster (APL 100%).
4. Set the color analyzer to the CHROMA mode and
after zero point calibration, bring the optical
receptor to the center on the tube surface (CRT).
5. Enter the Service mode in TV Mode.
6. Press [VOL n] button on the service remote
control to enter "C/D" mode. (Display changes "C/
D," "7f," "TUNER," "SLP R," "MONO," "DTV-H/-H2,"
"RATING," "RC5" "DL V-CHIP," and "D-SOUND"
cyclically when [VOL n] button is pressed.)
7. Press [4] button on the service remote control unit
for Red adjustment. Press [5] button on the service
remote control unit for Blue adjustment.
8. In each color mode, press [CH. o/p] buttons to
adjust the values of color.
1-7-4
P7753EA
9. Adjust Red and Blue color so that the temperature
becomes 9200K (x: 286 / y: 294) ±3%.
8. Focus Adjustment
10. At this time, check if horizontal line is white. If not,
adjust Cut-off Adjustment until the horizontal line
becomes pure white.
Purpose: Set the optimum Focus.
Symptom of Misadjustment: If Focus Adjustment is
incorrect, blurred images are shown on the display.
11. Turn off and on again to return to the normal mode.
Receive APL 100% white signal and confirm that
Chroma temperatures become 9200K (x: 286 / y:
294) ±3%.
Note: Confirm that Cut Off Adj. is correct after this
adjustment, and attempt Cut Off Adj, if needed.
Test Point
Adj. Point
Mode
Input
---
Focus Control
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
See below
7. Sub-Brightness Adjustment
Note: Focus Control FBT --- Sub CBA
FBT = Fly Back Transformer
Purpose: To get proper brightness.
1. Operate the unit more than 30 minutes.
Symptom of Misadjustment: If Sub-Brightness is
incorrect, proper brightness cannot be obtained by
adjusting the Brightness Control.
2. Face the unit to the East and degauss the CRT
using a degaussing coil.
Test Point
Adj. Point
Mode
Input
---
[CH. o/p]
buttons
RF
SMPTE
7.5IRE
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
4. Adjust the focus control on the FBT to obtain a
clear picture.
9. H. Position Adjustment
Purpose: To obtain correct horizontal position of
screen image.
Symptom of Misadjustment: H. position may not be
properly displayed.
Figure
White
3. Input the monoscope pattern.
Black
This bar
just
visible
Fig. 4
Note: SMPTE Setup level --- 7.5 IRE
1. Enter the Service mode.
Then input SMPTE signal from RF input.
2. Press [PICTURE] button on the service remote
control unit.
Test Point
Adj. Point
Mode
Input
---
[CH. o/p] buttons
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
---
1. Operate the unit for at least 20 minutes.
2. Enter the Service mode in TV mode.
3. Press [8] button on the service remote control unit
and select "H-P" mode.
4. Input monoscope pattern.
5. Press [CH. o / p] buttons on the service remote
control unit so that the left and right side of the
monoscope pattern are equal to each other.
3. Press [1] button on the service remote control unit
and selcet “BRT” mode. (Display changes “BRT,”
“CNT,” “COL,” “TNT,” “V-T,” and “SHP” cyclically
when [1] button is pressed.)
4. Press [CH o/p] buttons so that the bar is just
visible (See above figure).
1-7-5
P7753EA
10. V. Position Adjustment
Purpose: To obtain correct vertical position of screen
image.
Symptom of Misadjustment: If V. position is
incorrect, vertical position of image on the screen may
not be properly displayed.
Test Point
Adj. Point
Mode
Input
---
[CH. o/p] buttons
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
---
12. Head Switching Position
Adjustment
Purpose: Determine the Head Switching Position
during Playback.
Symptom of Misadjustment: May cause Head
Switching Noise or Vertical Jitter in the picture.
Note: Unit reads Head Switching Position
automatically and displays it on the screen (Upper Left
Corner).
1. Playback test tape (VFMS0001H6).
2. Enter the Service mode in TV mode.
1. Operate the unit for at least 20 minutes.
3. Press [5] button on the service remote control unit.
2. Enter the Service mode in TV mode.
4. The Head Switching position will display on the
screen; if adjustment is necessary follow step 4.
6.5H(412.7µs) is preferable.
3. Press [9] button on the service remote control unit
and select "V-P" mode. (Display changes "V-S" and
"V-P" cyclically when [9] button is pressed.)
4. Input monoscope pattern.
5. Press [CH. o / p] buttons on the service remote
control unit so that the top and bottom of the
monoscope pattern are equal each other.
11. V. Size Adjustment
5. Press [CH. o / p] buttons on the service remote
control unit if necessary. The value will be
changed in 0.5H steps up or down. Adjustable
range is up to 9.5H. If the value is beyond
adjustable range, the display will change as:
Lower out of range: 0.0H
Upper out of range: -.-H
Purpose: To obtain correct vertical height of screen
image.
Symptom of Misadjustment: If V. Size is incorrect,
vertical height of image on the screen may not be
properly displayed.
Test Point
Adj. Point
Mode
Input
---
[CH. o/p] buttons
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
90%±5%
1. Operate the unit for at least 20 minutes.
2. Enter the Service mode in TV mode.
3. Press [9] button on the service remote control unit
and select V-S mode. (Display changes "V-S" and
"V-P" cyclically when [9] button is pressed.)
4. Input monoscope pattern.
5. Press [CH. o / p] buttons on the remote control
unit so that the monoscope pattern is 90±5% of
display size and the circle is round.
1-7-6
P7753EA
The following 2 adjustments normally are not
attempted in the field. They should be done only
when replacing the CRT then adjust as a
preparation.
14. Convergence Adjustment
13. Purity Adjustment
Symptom of Misadjustment: If Convergence
Adjustment is incorrect, the edge of white letters may
have color edges.
Purpose: To obtain pure color.
Purpose: To obtain proper convergence of red, green
and blue beams.
Symptom of Misadjustment: If Color Purity
Adjustment is incorrect, large areas of color may not
be properly displayed.
Test Point
Adj. Point
Mode
Input
---
Deflection Yoke
Purity Magnet
---
*Red Color
Tape
M. EQ.
Spec.
---
Pattern Generator
See below
Test Point
Adj. Point
Mode
Input
---
C.P. Magnet (RB)
C.P. Magnet (RB-G)
Deflection Yoke
---
Dot Pattern
or
Crosshatch
Tape
M. EQ.
Spec.
---
Pattern Generator
See below
Figure
CRT
Figure
COIL SCREW PURITY RB
RB-G
RING LOCK
SCREW
GREEN
RED
BLUE
DY WEDGE
C.P. MAGNET CLAMPER
C.P. MAGNET
COIL CLAMPER
Fig. 5
DEFLECTION YOKE
Fig. 6
* This becomes RED COLOR if the [7] button is
pressed while in service mode.
C.P. MAGNET (RB)
1. Set the unit facing east.
2. Operate the unit for over 30 minutes before
adjusting.
R
R
3. Fully degauss the unit using an external
degaussing coil.
G
G
B
B
4. Set the unit to the AUX mode which is located
before CH2 then input a red raster from video in.
Fig. 7
5. Loosen the screw on the Deflection Yoke Clamper
and pull the Deflection Yoke back away from the
screen. (See Fig. 6.)
C.B. MAGNET (RB-G)
6. Loosen the Ring Lock and adjust the Purity
Magnets so that a red field is obtained at the
center of the screen. Tighten Ring Lock. (See Fig.
5, 6.)
7. Slowly push the Deflection Yoke toward the bell of
the CRT and set it where a uniform red field is
obtained.
8. Tighten the clamp screw on the Deflection Yoke.
RB
RB
G
G
Fig. 8
1. Set the unit to the AUX mode which is located
before CH2 then input a dot or crosshatch pattern.
2. Loosen the Ring Lock and align red with blue dots
or crosshatch at the center of the screen by
rotating (RB) C.P. Magnets. (See Fig. 7.)
3. Align red / blue with green dots at the center of the
screen by rotating (RB-G) C.P. Magnet.
(See Fig. 8.)
1-7-7
P7753EA
4. Fix the C.P. Magnets by tightening the Ring Lock.
5. Remove the DY Wedges and slightly tilt the
Deflection Yoke horizontally and vertically to
obtain the best overall convergence.
6. Fix the Deflection Yoke by carefully inserting the
DY Wedges between CRT and Deflection Yoke.
1-7-8
P7753EA
HOW TO INITIALIZE THE TV/DVD/VCR
To put the program back at the factory-default, initialize the TV/DVD/VCR as the following procedure.
< DVD Section >
< TV/VCR Section >
1. Turn the power on and press [SELECT] button on
the remote control unit to put the TV/DVD/VCR
into DVD mode.
1. Use the service remote control unit.
2. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. a appears on the screen.
3. Press [DISC MENU] button on the service remote
control unit to enter Service mode. (Refer to “How
to enter Service mode” on page 1-7-1.)
"*******" differ depending on the models.
MODEL : *******
Version : *.**
Region : *
EEPROM CLEAR : CLEAR
EXIT: SELECT
4. Press [VOL n] button on the service remote
control unit twice, and confirm that OSD indication
is “7F = FF.” If needed, set it to become “7F = FF”
by pressing [CH. o/p] buttons on the service
remote control unit.
5. Confirm that OSD indication on the four corners
on TV screen changes from on and off light
indication to red by pressing [DISPLAY] button. (It
is necessary for one or two seconds.)
6. Press [STANDBY-ON] button to release from
Service mode.
Fig. a
3. Press [CLEAR] button on the remote control unit.
Fig. b appears on the screen.
"*******" differ depending on the models.
MODEL : *******
Version : *.**
Region : *
< DTV Section >
1. Use the service remote control unit.
2. Turn the power on and press [SELECT] button to
select DTV mode. (Use main power on the TV
unit.)
3. Press [DISC MENU] button on the service remote
control unit to enter Service mode. (Refer to “How
to enter Service mode” on page 1-7-1.)
EEPROM CLEAR : OK
EEPROM CLEAR : CLEAR
2. Turn the power on and press [SELECT] button to
select TV mode. (Use main power on the TV unit.)
EXIT: SELECT
Fig. b
4. Confirm that OSD indication on the four corners
on TV screen changes to red by pressing
[DISPLAY] button.
5. Press [STANDBY-ON] button to release from
Service mode.
When “OK” appears on the screen, the factory
default will be set.
6. Press [SELECT] button to change to AUX mode.
4. To exit this mode, press [CH. o/p] or [SELECT]
button to go to TV mode, or press [STANDBY-ON]
button to turn the power off.
< Both TV/VCR and DTV Section >
1. Turn the power on and press [SELECT] button to
select DTV mode.
2. Press [DISC MENU] button to enter Service mode.
3. Press [DISPLAY] button to initialize in DTV mode.
4. Press [STANDBY-ON] button to release from
Service mode.
5. Press [SELECT] button to change to AUX mode.
6. Press [DISC MENU] button to enter Service mode.
7. Press [DISPLAY] button to initialize in TV mode.
8. Press [STANDBY-ON] button (or [RETURN] and
[5] buttons) to release from Service mode.
Initializing is complete.
1-8-1
P7754INT
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on
the remote control unit to put the TV/DVD/VCR
into DVD mode. Then remove the disc on the tray.
(It is possible to move to F/W version up mode
only when the TV/DVD/VCR is in DVD mode with
the tray open.)
"*******" differs depending on the models.
F/W Version Up Mode
(*2)
VERSION :
Completed
SUM : 7ABC
Model No : *******
VERSION : *.**
************.***
2. To put the TV/DVD/VCR into F/W version up
mode, press [9], [8], [7], [6], and [MODE] buttons
on the remote control unit in that order.
Fig. a appears on the screen.
"*******" differs depending on the models.
F/W Version Up Mode
Model No : *******
VERSION : *.**
Please insert a DISC
for F/W Version Up.
Fig. c Completed Program Mode Screen
At this time, no button is available.
6. Remove the disc on the tray.
7. Press [SELECT] button on the remote control unit
to go to TV mode, or press [STANDBY-ON] button
on the unit to turn the power off.
EXIT: SELECT
Fig. a Version Up Mode Screen
The TV/DVD/VCR can also enter the version up
mode with the tray open. In this case, Fig. a will be
shown on the screen while the tray is open.
8. Press [SELECT] button on the remote control unit
to put the TV/DVD/VCR into DVD mode again.
9. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. d appears on the screen.
"*******" differs depending on the models.
3. Load the disc for version up.
MODEL : *******
Version : *.**
Region : *
4. The TV/DVD/VCR enters the F/W version up
mode automatically. Fig. b appears on the screen.
If you enter the F/W for different models, “Disc
Error” will appear on the screen, then the tray will
open automatically.
EEPROM CLEAR : CLEAR
"*******" differs depending on the models.
F/W Version Up Mode
(*1)
VERSION :
Reading...
Model No : *******
VERSION : *.**
************.***
EXIT: SELECT
Fig. d
10. Press [CLEAR] button on the remote control unit.
Fig. e appears on the screen.
"*******" differs depending on the models.
MODEL : *******
Version : *.**
Region : *
Fig. b Programming Mode Screen
EEPROM CLEAR : OK
The appearance shown in (*1) of Fig. b is
described as follows:
No.
Appearance
EEPROM CLEAR : CLEAR
State
1
Reading...
Sending files into the memory
2
Erasing...
Erasing previous version data
3
Programming... Writing new version data
5. After programming is finished, the tray opens
automatically. Fig. c appears on the screen and
the checksum will be shown in (*2) of Fig. c.
EXIT: SELECT
Fig. e
When “OK” appears on the screen, the factory
default will be set. Then the firmware renewal
mode is complete.
11. To exit this mode, press [CH. o / p] or [SELECT]
button to go to TV mode, or press [STANDBY-ON]
button to turn the power off.
1-9-1
P7754FW
TO DVD SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
<DVD SECTION>
CN1A
SUB CBA
1-10-1
DRUM
MOTOR
M
LOADING
MOTOR
PG
SENSOR
CYLINDER ASSEMBLY
CONTROL
HEAD
ACE HEAD ASSEMBLY
(DECK ASSEMBLY)
18
16
17
19
CN1
DVD-SDATA
DVD-SCLK
DVD-CS
DVD-REMOTE
M
SW2401 SW2408
KEY SWITCH
FUNCTION CBA
CN2301
13
14
15
12
CN1104
5
M
CAPSTAN
MOTOR
MOTOR
DRIVE
CIRCUIT
CAPSTAN MOTOR
AL+5V
RESET
Q1205
CM+12V
P-ON+5V(3)
TIMER+5V
AL+5V
DEF+B
T-REEL
Q1206
SW1212
LD-SW
TP1202
CTL-AMP-OUT
D1217 TV/VCR
D1216 DVD
D1204 REC
WF3
AL+5V
RS1201
REMOTE
SENSOR
D1224 S-LED
BUFFER
SW1211
REC
SAFETY
BUFFER
Q1209
SW1201 SW1203,
SW1206 SW1210
KEY SWITCH
CL1201
CM+12V
1
P-ON+5V(3) 2
C-FG
3
4
CM-F/R
C-CONT
5
6
FG-GND
LD-CONT
7
D-CONT
8
D-PFG
9
M-GND
10
D/L+12V
11
VG+15V
12
SENSOR CBA
(END-SENSOR)
SENSOR CBA
(ST-SENSOR)
Q1201
BUFFER
END-SENS.
CL1402
5
6
Q1207
Q1208
ST-SENS.
Q1202
CTL(+)
CTL(-)
CN1301
DVD-SDATA 13
DVD-SCLK
14
DVD-CS
15
DVD-REMOTE 12
CN2401
5 KEY-1
MAIN CBA
81
85
67
65
66
75
42
31
84
DTV-ON-H 30
C-SYNC 74
SPOT-KILL 41
AFT 8
SCL 71
SDA 72
2
I C-OPEN 45
82 LD-CONT
77 D-CONT
90 D-PFG
87 C-FG
73 C-F/R
76 C-CONT
V-H-SW
ENV-DET
DV-SYNC
V-ENV
ROTA
RF-SW
YCA-SCL
YCA-SDA
YCA-CS
DVD-H
AUDIO-MUTE
DVD-AUDIO-MUTE
D-REC-H
34 RESET
SP-MUTE
DIGITAL-AUDIO-H
VOLUME
16
17
13
10
15
18
70
68
69
48
24
47
44
12
83
11
ST/SAP-IN 4
33 REC-SAFETY NORMAL-H 22
80 T-REEL
Hi-Fi-H-SW 19
9 ST-SENS.
7 END-SENS.
1 LD-SW
CTL(-)
CTL-AMP-OUT P-ON-H2
DVD-MAIN-POWER
P-ON-H
P-DOWN
TV/VCR-LED
CTL(+)
2 DVD-LED
26
95
94
97
DTV-S-RESET
DTV-S-SREQ
DTV-S-SCLK
DTV-S-SIN
DTV-S-SOUT
DVD-SDATA
DVD-SCLK
BUS-CONT 32
DVD-CS
DVD-REMOTE
21 REC-LED
52
51
50
25
14 REMOTE
5 KEY-0
6 KEY-1
Q1210
Q1108
Q1109
IC1201(SERVO/SYSTEM CONTROL)
Q1113
Q1112
V-H-SW
ENV-DET
DV-SYNC
V-ENV
ROTA
RF-SW
YCA-SCL
YCA-SDA
YCA-CS
DVD-H
AUDIO-MUTE
DVD-AUDIO-MUTE
D-REC-H
SP-MUTE
DIGITAL-AUDIO-H
VOLUME
YCA-SCL
YCA-SDA
YCA-CS
SDA
SCL
ST/SAP-IN
NORMAL-H
Hi-Fi-H-SW
AUDIO-MUTE
DTV-ON-H
P-ON-H2
DVD-MAIN-POWER
P-ON-H
P-DOWN
SPOT-KILL
AFT
SCL
SDA
C-SYNC
6 SCL
5 SDA
7 CS
TO VIDEO
BLOCK DIAGRAM
TO AUDIO
BLOCK DIAGRAM
TO Hi-Fi AUDIO
BLOCK DIAGRAM
TO POWER
SUPPLY BLOCK
DIAGRAM
TO TV PROCESS
BLOCK DIAGRAM
IC1202 (MEMORY)
DTV-S-RESET
DTV-S-SREQ
DTV-S-SCLK
DTV-S-SIN
DTV-S-SOUT
SCL
SDA
TO DTV
BLOCK
DIAGRAM
IC1104 (MEMORY)
6 SCL
5 SDA
System Control / Servo Block Diagram
BLOCK DIAGRAMS < TV/VCR Section >
P7754BLS
1-10-2
JK1701
YCA-SCL
YCA-SDA
YCA-CS
DV-SYNC
DTV-VIDEO
CYLINDER ASSEMBLY
VIDEO (R)-2 HEAD
VIDEO (L)-2 HEAD
VIDEO (L)-1 HEAD
VIDEO (R)-1 HEAD
(DECK ASSEMBLY)
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
VIDEO-IN
TO DTV
BLOCK DIAGRAM
TO TV PROCESS
BLOCK DIAGRAM
VIDEO
TU-VIDEO
EXT-VIDEO
Q1404
BUFFER
WF4
LINE
DTV
TUNER
VIDEO
AGC
53
SERIAL
54
I/F
55
24 DV-SYNC
30
28
32
Q1401
BUFFER
9
8
7
6
5
4
Y/C
MIX
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
CL1401
VIDEO(R)-1
VIDEO-COM1
VIDEO(L)-1
VIDEO(L)-2
VIDEO-COM2
VIDEO(R)-2
R P
FBC
QV/QH
6dB
AMP
IC1401
(VIDEO SIGNAL PROCESS/ HEAD AMP) 26
WF5
TP1401
V-OUT
ROTA
RF-SW
V-ENV
V-H-SW
ENV-DET
WF1
57 ROTA/RF-SW
59 V-ENV
58
60 ENV-DET
TP1402
RF-SW
EP
HEAD
AMP
67
66
65
37
SP
HEAD
AMP
36
74
73
72
VCA
MAIN CBA
39
CHROMINANCE
SIGNAL PROCESS
EP
SP
VXO
Q1402
BUFFER
YNR/COMB FILTER
CCD 1H
DELAY
34
49
50
CLAMP
WF2
X1401
3.58MHz
70
69
P
R
LUMINANCE
SIGNAL PROCESS
REC VIDEO SIGNAL
WF6
TP1403
ENV.
14
PB VIDEO SIGNAL
Video Block Diagram
P7754BLV
Q2608
BUFFER
Q2601
BUFFER
WF19
1-10-3
JK2601
AUDIO-OUT(R)
AUDIO-OUT(L)
N-A-IN
N-A-OUT
SP-MUTE
DVD-AUDIO-MUTE
DIGITAL-AUDIO-H
VOLUME
DTV-SPDIF
DVD-H
FULL
ERASE
HEAD
FE HEAD
AUDIO
ERASE
HEAD
AUDIO
HEAD
Q1850
DIGITAL
AUDIO-OUT
(COXIAL)
ACE HEAD ASSEMBLY
(DECK ASSEMBLY)
TO Hi-Fi AUDIO
BLOCK DIAGRAM
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
TO DTV
BLOCK DIAGRAM
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
CN2301
19 DVD-AUDIO(R)
17 DVD-AUDIO(L)
16 DVD-AUDIO-MUTE
1
2
3
5
CN1302
13
CN1301
19
17
16
9 10
SW CTL
DTV
DVD
DTV
DVD
15
4
CL1402
AUDIO-PB/REC
AUDIO-COM
AE-H
FE-H
CL1403
1 FE-H
2 FE-H-GND
4
3
1
2
IC1850 (INPUT SELECT)
WF20 Q2609
CN2302
13 DTV-SPDIF
BUFFER
DTV-AUDIO(R)
DTV-AUDIO(L)
MAIN CBA
SUB CBA
CN2
3
4
9
1
TO DTV
BLOCK DIAGRAM
TO
DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
<DVD
SECTION>
CN2A
8
6
3
1
REC AUDIO SIGNAL
12
Q1874
Q1875
Q1873
Q1872
BIAS
OSC
DVD/DTV
(L-CH)
VCR
(R-CH)
DVD/DTV
VCR
Q1871
P-ON+5V
P-ON+5V
2
MUTE
/STANDBY
CONTROL
IC1803 (AUDIO AMP)
7
11
14
8
SP/LP-ON
AUTO
BIAS
5
EQ
AMP
4
3
CN3802
1,2
WF8
80
2
9
78
P
LPF
TUNER
76
REC
AMP
ALC
R
FRONT
REAR
FUNCTION
CBA
58
LINE
AMP
YCA-SCL
YCA-SDA
YCA-CS
AUDIO-MUTE
D-REC-H
55 54 53
SERIAL
I/F
MUTE
JUNCTION-B CBA
CL3801
SP(L)
1
SP-GND 2
CL3802
SP(R)
1
SP-GND 2
JUNCTION-A CBA
JK1801
HEADPHONE
JACK
CN1104
CN3801
CN2401 CN2801
1,3 SP(L) 1,3
1,2 SP(L) 1,2
CN1802
1,2 SP(R)
DVD AUDIO SIGNAL
IC1401
(AUDIO SIGNAL PROCESS)
11
6
AMP
VOLUME
AMP
PB AUDIO SIGNAL
WF7
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
10
SP801
SPEAKER
L-CH
SP1801
SPEAKER
R-CH
Audio Block Diagram
P7754BLA
1-10-4
N-A-OUT
DTV-AUDIO(R)
DTV-AUDIO(L)
TO DTV
BLOCK
DIAGRAM
JK1702
JK1703
SIF
TO AUDIO
BLOCK
DIAGRAM
AUDIO(L)-IN
AUDIO(R)-IN
TO TV
PROCESS
BLOCK
DIAGRAM
7
9
6
69
71
57
L-CH
INSEL
NOR
SW
R-CH
INSEL
SIF
DEMOD
SAP
DET
13
48
14
47
63
STEREO
PLL
PILOT
DET
P
L-CH
PNR
R-CH
PNR
P
R
R
SW
NOISE
LIM
LIM
NOISE
SW
PILOT
CANCEL
STEREO
FILTER
62
SAP
DEMOD
SAP
FILTER
CONT
IC1701 (MTS/ SAP/ Hi-Fi AUDIO PROCESS/ Hi-Fi HEAD AMP)
DEV
DEV
COMP
VCO
NOISE
DET
HOLD
PULSE
VCO
COMP
L-R
DEMOD
MAIN CBA
LPF
MATRIX
LPF
ST/SAP
SW
L-CH BPF
COMP
OUTPUT
SELECT
R-CH BPF
D.C
dBX
DEC
LIM
MATRIX
34
DO
DET
33
ENV
DET
L
R
54
37
38
27
24
26
1
39
49
77
78
80
4
MODE
40
OUT
23
RIPPLE
FILTER
SERIAL
DATA
DECODER
N-A-IN
Hi-Fi-H-SW
AUDIO-MUTE
AUDIO-OUT(R)
AUDIO-OUT(L)
CL1401
Hi-Fi-AUDIO(R) 3
Hi-Fi-COM
2
Hi-Fi-AUDIO(L) 1
Q1701
ST/SAP-IN
NORMAL-H
Hi-Fi
AUDIO
(L) HEAD
Hi-Fi
AUDIO
(R) HEAD
CYLINDER
ASSEMBLY
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
TO AUDIO
BLOCK DIAGRAM
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
PB AUDIO SIGNAL
SDA
SCL
TP1703
A-OUT-YCA
P-ON+9V
REC AUDIO SIGNAL
Hi-Fi Audio Block Diagram
P7754BLH
1-10-5
SDA
SCL
C-SYNC
AFT
SPOT-KILL
AIF 7
OSD-R
OSD-G
OSD-B
OSD-BLK
WF16 V-SYNC
WF15 H-SYNC
64
63
62
60
59
58
CV-IN 56
IC1201
(SYSTEM CONTROL/OSD)
TO SYSTEM
CONTROL
/SERVO
BLOCK
DIAGRAM
TU1010
CN1301
4
5
6
3
7
8
9
OSD-R
OSD-G
OSD-B
OSD-BLK
V-SYNC
H-SYNC
SPOT-KILL
CN2301
4
5
6
3
7
8
9
CN2301
1
2
CN2302
15
7
CN1302
15 FSC
7 C-VIDEO
BUFFER
Q1403
CN1301
1 SDA
2 SCL
CN2103
17
CN1103
17 C-SYNC
12
11
10
13
9
8
14
15
31
16
6
SAW
FILTER
SF1001
AMP
VIF
AMP
AFT
VCO
VIDEO
DET
IC1001(IF SIGNAL PROCESS)
4
V-SYNC
PROCESS
CIRCUIT
SYNC
SEPARATION
SERIAL
I/F
H-SYNC
PROCESS
CIRCUIT
INTELLIGENT
MONITORING
CHROMA
SIGNAL
PROCESS
CIRCUIT
LUMA
SIGNAL
PROCESS
CIRCUIT
OSD MIX/RBG MATRIX/
BLIGHT/DRIVE AMP/
HV BLANKING
CHROMA
BPF
Cb/Cr
DELAY
+8V
4.5MHz
FILTER
CF1032
CHROMA
TRAP
IC2301 (CHROMA/DEFLECTION SIGNAL PROCESS)
11
13
16
17
FILTER
TUNING
TUNER
VCR
LINE
DVD
TUNER
VCR
LINE
DVD
SUB CBA
VXCO
+5.7V REG.
7
40
41
35
5
34
2
3
4
18
28
21
24
26
23
25
20
29
27
WF18
WF17
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
<DVD SECTION>
CN2A
CN1302
1
11
10
9
17
5
3
Q2304
TP2505
V-RAMP
AFC
H-DRIVE
V-DRIVE
ACL
V-RAMP-NF
BLUE
GREEN
RED
VIDEO
EXT-VIDEO
DTV-Cr
DTV-Cb
DTV-Y
+5.7V-CTRL
WF9
TP2503
H-DRIVE
TP2502
V-DRIVE
SIF
TO CRT/H.V.
BLOCK
DIAGRAM
TO CRT/H.V.
BLOCK
DIAGRAM
TO VIDEO
BLOCK
DIAGRAM
TO DTV
BLOCK
DIAGRAM
TO POWER
SUPPLY
BLOCK
DIAGRAM
TO VIDEO
BLOCK
DIAGRAM
TO
Hi-Fi AUDIO
BLOCK D
IAGRAM
Mode : SP/REC
TV-VIDEO
MAIN CBA
REC AUDIO SIGNAL
TP1301 TP1302 TP1303
BLUE GREEN RED
+5.7V-CTRL
DTV-Cr
DTV-Cb
DTV-Y
TV-VIDEO
VIDEO
EXT-VIDEO
1
8
CN2
8 DVD-Y
6 DVD-C
CN2302
1
11
10
9
17
5
3
EQ
AMP
SIF
AMP
DVD VIDEO SIGNAL
X2301
3.58MHz
SIF
AMP
PB VIDEO SIGNAL
BASEBAND
TINT
REC VIDEO SIGNAL
TV Process Block Diagram
P7754BLT
SCL 4
SDA 5
DIF-OUT1 10
DIF-OUT2 11
DIF-AGC 8
TU1010
(TUNER UNIT)
25MHz
OSC
X281
27MHz
OSC
X271
LPF
ADC
/AGC I/F
4 XIN-25MHz
5 XOUT-25MHz
14 XIN-27MHz
15 XOUT-27MHz
174
178
140
SYSTEM DECODER
/VIDEO DECODER
/VIDEO FORMAT
CONVERTER
/2D GRAPHICS
DIGITAL SIGNAL
PROCESS
IC101 (DTV SIGNAL PROCESS)
IC202 (FLASH MEMORY)
*1 79~81,85,87,89~91,92,94,96~98,
102,104,106
*2 55,56,58,60,61,116,119,120,124,
125,127,129,130
FLASH MEMORY
*3 1,2,7~12,20,206,209,211,213~216,
*4 23~25,27,29,32~36,41~44,47,48,50,
52~54,205
IC201 (DDR SDRAM)
*5 1~10,13,16~25,48
*6 29~36,38~45
*7 28~32,35~42
DDR SDRAM
*8 2,4,5,7,8,10,11,13,54,56,57,59,60,
62,63,65
CN1102
CN102
11 DIF-OUT1 11
12 DIF-OUT2 12
9 DIF-AGC 9
1-10-6
DATA BUS(0-15)
ADDRESS BUS(0-12)
DATA BUS(0-15)
MAIN CBA
*8
*7
*6
*4
*3
*2
*1
38
155
153
154
204
Q251
6
5
7
8
BUFFER
BUFFER
Q245
BUFFER
BUFFER
Q214
Q213
CN101
2
14
15
Q212
SW
5
SW
4
Q211
7
8
9
10
12
DTV MODULE CBA UNIT
L-CH
AUDIO
15
D/A
R-CH
CONVERTER
14
IC252
(AUDIO D/A CONVERTER)
Q244
Q243
ADDRESS BUS(1-22)
FLASH
MEMORY
I/F
SDRAM
I/F
DTV-S-SREQ
DTV-S-SCLK
DTV-S-SIN
DTV-S-SOUT
DTV-S-RESET
*5
159
158
162
161
156
189
182
187
186
SDA 144
SCL 143
BUS-CONT 41
AUDIO
DECODER
VIDEO
ENCODER
CN102
14
18
19
20
15
16
CN1101
DTV-SPDIF 2
SDA
14
SCL
15
TU-SDA
5
TU-SCL
4
DTV-S-SREQ 7
DTV-S-SCLK 8
DTV-S-SIN
9
DTV-S-SOUT 10
DTV-S-RESET 12
CN1102
DTV-VIDEO 14
DTV-Y
18
DTV-Cr
19
DTV-Cb
20
DTV-AUDIO(L) 15
DTV-AUDIO(R) 16
REC VIDEO SIGNAL
SDA
SCL
DTV-S-SREQ
DTV-S-SCLK
DTV-S-SIN
DTV-S-SOUT
DTV-S-RESET
DTV-SPDIF
DTV-AUDIO(R)
DTV-AUDIO(L)
DTV-AUDIO(L)
DTV-AUDIO(R)
DTV-Y
DTV-Cr
DTV-Cb
DTV-VIDEO
TO SYSTEM
CONTROL
/SERVO
BLOCK
DIAGRAM
TO AUDIO
BLOCK
DIAGRAM
TO Hi-Fi
AUDIO
BLOCK
DIAGRAM
TO TV
PROCESS
BLOCK
DIAGRAM
TO VIDEO
BLOCK
DIAGRAM
REC AUDIO SIGNAL
DTV Block Diagram
P7754BLDT
1-10-7
TO TV PROCESS
BLOCK DIAGRAM
TO TV PROCESS
BLOCK DIAGRAM
TO POWER
SUPPLY
BLOCK
DIAGRAM
CN1103
CN2103
1
2
6
RED
GREEN
BLUE
V-DRIVE
H-DRIVE
AFC
ACL
V-RAMP-NF
+B
+B
DEF+B
CL2504A
2 RED
3 GREEN
4 BLUE
CL2504B
2
3
4
TP2506
AFC
WF10
H.DRIVE
Q2591
SUB CBA
TP2504
GND
TP2501
+B
H.OUTPUT
Q2571
4
5
3
1
Q2503
RED AMP
T2572
WF12
AMP
11
S
F
3
PULSE
UP
FOCUS
SCREEN
ANODE
WF13
Q2501
BLUE AMP
CL2501B
1
3
PB VIDEO SIGNAL
CL2501A
1 HEATER
3 +180V
GREEN AMP
Q2502
5
SCREEN VR
FOCUS VR
HV
CRT CBA
6
9
7
10
8
VCC
2 6
T2571 F.B.T.
1
7
THERMAL
PROTECTION
IC2551(V-DEFLECTION CONTROL)
REC VIDEO SIGNAL
WF14
JK2501
CN2501
3
4
5
1
HDRIVE
VDRIVE
L551
D.Y.
GND
HEATER
R
G
B
V501
CRT
ANODE
FOCUS
SCREEN
GND
CN2571
WF11
DVD VIDEO SIGNAL
CRT/H.V. Block Diagram
P7754BLCRT
LINE
FILTER
L1601
PS1601
F1601
4A/125V
DG601
DEGAUSSING CN1601
COIL
W1601
4A 125V
Q1602
Q1904
D1606
BRIDGE
RECTIFIER
D1603
1-10-8
HOT
SWITCHING
Q1905
SWITCHING
Q1601
1
2
3
IC1902
ERROR
VOLTAGE DET
15
4
2
3
16
5
13
14
7
T1901
2
3
2
1
1
IC1901
(ISOLATOR)
IC1601
ERROR
VOLTAGE DET
11
13
14
15
16
10
9
4
3
4
8
7
5
2
T1601
COLD
Q1907
Q1903
Q1901
FEED
Q1604 BACK
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
Q1906
Q1908
MAIN CBA
Q1902
SW+5V
Q1605
VR1601
+B ADJ
4A 125V
Q1688
SW+5V
Q1607
CN2103
10
19
12
IC3603
SW CTL
Q2615
Q2612
Q1106
Q2610
IC1682
+5V REG.
IC1101
+1.8V REG.
Q1681
SW+5V
CN1302
CN2302
2 DVD-MAIN-POWER 2
CN1103
10 DVD+9V
19 EV+4V
12 DVD+5V
IC1105,Q1110
+3.3V REG.
IC1106,Q1107
+2.5V REG.
Q1689
SW+5V
Q1614
SW+9V
Q1613
SW+8V
Q2617
IC2602
3 +1.2V 2
REG.
CN1
14
13
12
11
10
9
3
2
1
15
EV+9V
EV+9V
DVD-ON+5V
DVD-ON+3.3V
EV+3.3V
EV+3.3V
EV+1.2V
EV+1.2V
EV+1.2V
PWRCON
Q1105 CN1101
+5V REG.
3 DT+5V
Q2616
Q2618
Q2611
SUB CBA
Q1103
Q1104
TO SYSTEM
CONTROL
/SERVO
BLOCK
DIAGRAM
TO TV
PROCESS
BLOCK
DIAGRAM
DVD MAIN
DTV-ON +5V
CN1A CBA UNIT
14
13
EV+9V
12
DVD-ON+5V
11
DVD-ON+3.3V
10
EV+3.3V
9
3
EV+1.2V
2
1
15
PWRCON
TO DVD SYSTEM
CONTROL / SERVO
BLOCK DIAGRAM
<DVD SECTION>
CN101
3
DTV-ON+1.8V
DTV-ON+3.3V
DTV-ON+2.5V
DTV MODULE
CBA UNIT
P-DOWN
P-ON-H
DVD-MAIN-POWER
P-ON-H2
DTV-ON-H
Q1221
TO CRT/H.V.
BLOCK DIAGRAM
CN2103
AL+33V
DEF+B
P-ON+12V
P-ON+8V
P-ON+9V
P-ON+5V(4)
P-ON+5V(2)
P-ON+5V(3)
P-ON+5V(5)
TIMER+5V
AL+5V
M+12V
+5.7V-CTRL
CN1103
1 +B
2 +B
6 DEF+B
CN102
CN1102
6 DTV-ON+1.8V 6
4 DTV-ON+3.3V 4
5 DTV-ON+2.5V 5
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Power Supply Block Diagram
P7754BLP
1-10-9
SLED
MOTOR
M
M
SPINDLE
MOTOR
TRAY-IN
TS(+)
TS(-)
DRIVE CBA
TO DIGITAL SIGNAL
PROCESS BLOCK
DIAGRAM
FS(+)
FS(-)
SP(+)
SP(-)
TRAY-IN
GND
SL(-)
SL(+)
CN301
6
5
1
4
3
2
+
SLED
MOTOR
DRIVE
17
18
8
7
5
6
10
9
1
3
2
IC202
(OP AMP)
-
DVD MAIN CBA UNIT
+3.3V
+
SPINDLE
MOTOR
DRIVE
12
11
-
+
-
-
+
TRACKING
ACTUATOR
DRIVE
FOCUS
ACTUATOR
DRIVE
14
13
15
16
IC301 (SERVO DRIVE)
-
+
-
+
-
+
VREF
23
6
4
5
3
1
2
25
24
27
26
65 TRAY-IN
63 SL-AMP
122 SL-ADS
121 SP-ROT
67 SLD
66 SPDL
123 TD-OFST
126 TRACKING
DRIVE
124 FD-OFST
127 FOCUS DRIVE
55
54
53
49
PWRCON 46
DVD-SDATA
DVD-CS
DVD-SCLK
DVD-REMOTE
IC101 (MICRO CONTROLLER)
PWRCON
TO POWER SUPPLY
BLOCK DIAGARAM
<TV/VCR SECTION>
CN1A
18
17
16
19
DVD-SDATA
DVD-CS
DVD-SCLK
DVD-REMOTE
TO SYSTEM CONTROL
/SERVO BLOCK
DIAGRAM
<TV/VCR SECTION>
CN1
DVD System Control / Servo Block Diagram
BLOCK DIAGRAMS < DVD Section >
P7754BLSD
FS
PICK-UP
UNIT
TS
DETECTOR
C
D
A
B
CD/DVD
FS(+)
FS(-)
TS(+)
TS(-)
CD-LD
DVD-LD
PD-MONI
GND(DVD-PD)
GND(CD-PD)
GND(LD)
SDRAM
12
39
49
CN201
2
3
1
4
CD
4
6
FS(+)
FS(-)
TS(+)
TS(-)
IC201
(SW)
DVD
159
DATA
RAM
INST.
ROM
INTERRUPT
CONTROLLER
RF
SIGNAL
PROCESS
CIRCUIT
TO SYSTEM
CONTROL/SERVO
BLOCK DIAGRAM
62 CD/DVD
106
104
105
103
99
100
98
97
115
116
113
114
178
SDRAM DATA(0-15)
DVD MAIN CBA UNIT
1 3
Q253,Q254
CN201
10
AMP
8
AMP
Q251,Q252
7
6
5
9
CN201
16
18
17
15
19
SDRAM DATA(0-15)
TIMER
ECC
CPU
I/F
BCU
DMA
DECODER
I/F
STREAM
I/F
CPU
I/F
BCU
DEBUG
21~30 34~42 212
READ
MEMORY
UMAC
1~4 7~14 17~18 215~216
WATCH DOG
TIMER
32BIT
CPU
DVD/CD
FORMATTER
IC101 (MICRO CONTROLLER)
20
194
24
SDRAM ADDRESS(0-10)
SDRAM ADDRESS(0-10)
27
209
32
EXTERNAL
MEMORY
I/F
2
~
~
~
~
~
~
IC501 (SDRAM)
INST
CACHE
VIDEO
I/F
AUDIO
I/F
INST.
ROM
DATA
RAM
INST.
ROM
DATA
RAM
DATA
CACHE
32BIT CPU
REMOTE
CONTROL
WATCH DOG
TIMER
TIMER
INTERRUPT
CONTROLLER
GENERAL
I/O
SERIAL
I/O
PROCESSOR
DSP
DECODER
NTSC/PAL
ENCODER
AUDIO D/A
CONVERTER
C
139
131
FDQ (0-15)
FADR (0-19)
D/A
D/A
Y
152
151
146
144
29
36
48
16
25
1
9
38
45
FLASH
ROM
IC103 (FLASH ROM)
TO
TV PROCESS
BLOCK
DIAGRAM
<TV/VCR
SECTION>
CN2
TO AUDIO
BLOCK DIAGRAM
<TV/VCR SECTION>
CN2
DVD-SPDIF
DVD-AUDIO-MUTE
DVD-AUDIO(R)
DVD-AUDIO(L)
CN2A
8 DVD-Y
6 DVD-C
CN2A
1
9
3
4
DVD AUDIO SIGNAL
~
~
~
1-10-10
~
DVD VIDEO SIGNAL
Digital Signal Process Block Diagram
P7754BLD
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10-6 µF).
5. All voltages are DC voltages unless otherwise
specified.
1-11-1
X8TN_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY
WITH SAME TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the
power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Mode: SP/REC
5. Voltage indications on the schematics are as shown below:
< DVD Section >
1
2
3
5.0
5.0
(2.5)
< TV/VCR Section >
PLAY mode
STOP mode
The same voltage for
both PLAY & STOP modes Indicates that the voltage
is not consistent here.
1
2
5.0
The same voltage for
PLAY, REC & DVD
modes
Unit: Volts
PLAY mode
REC mode
DVD mode
3
5.0
(2.5)
<0>
Indicates that the voltage
is not consistent here.
6. How to read converged lines
1-D3
3
Distinction Area
Line Number
(1 to 3 digits)
AREA D3
2
Examples:
1. "1-D3" means that line number "1" goes to the line number
1
"1" of the area "D3".
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
1-B1
AREA B1
1-D3
A
B
C
D
7. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
1-11-2
X8TN_SC
Main 1/6 & Sensor Schematic Diagram < TV/VCR Section >
1-11-3
P7754SCM1
Main 2/6 Schematic Diagram < TV/VCR Section >
1-11-4
P7754SCM2
Main 3/6 Schematic Diagram < TV/VCR Section >
1-11-5
P7754SCM3
Main 4/6 Schematic Diagram < TV/VCR Section >
1-11-6
P7754SCM4
Main 5/6 & Junction-A Schematic Diagram < TV/VCR Section >
1-11-7
P7754SCM5
Main 6/6 Schematic Diagram < TV/VCR Section >
4A 125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
1-11-8
VOLTAGE CHART (Power off mode)
2
3
Ref. No.
1
0.1
0
IC1601
0
0
0
IC1901
1.1
10.3
0.7
IC1902
11.3
1
2
Ref. No.
1.1
0
IC1682
S
D
Ref. No.
0.1
167.1
Q1601
0.1
167.6
Q1905
E
C
Ref. No.
0
5.1
Q1221
0
1.1
Q1602
0
0.1
Q1604
0
0
Q1605
0
2.1
Q1607
0
0
Q1613
0
0
Q1614
Q1681
0
1.1
Q1688
0
1.1
Q1689
0
1.1
Q1901
1.2
1.1
Q1902
5.6
7.0
Q1903
6.8
10.3
Q1904
0
1.1
Q1906
0
7.4
Q1907
0
6.8
0
0.1
Q1908
4
2.2
0.1
1.1
3
1.1
G
1.1
1.1
B
0
0.1
0
0
0
0.1
0
0
0
0
0.5
6.6
7.4
0.7
0.1
0.1
0.7
P7754SCM6
Sub 1/3 Schematic Diagram < TV/VCR Section >
1-11-9
P7754SCSUB1
Sub 2/3 Schematic Diagram < TV/VCR Section >
1-11-10
P7754SCSUB2
Sub 3/3 Schematic Diagram < TV/VCR Section >
1-11-11
P7754SCSUB3
CRT Schematic Diagram < TV/VCR Section >
P7754SCCRT
Function & Junction-B Schematic Diagram < TV/VCR Section >
P7754SCF
1-11-12
DTV Module 1/2 Schematic Diagram < TV/VCR Section >
1-11-13
P7754SCDT1
DTV Module 2/2 Schematic Diagram < TV/VCR Section >
VOLTAGE CHART
CN101
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
1.9
5.2
3.4
3.4
0
2.8
3.2
3.3
0.2
0
3.4
0
3.2
3.2
CN102
1-11-14
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
--4.9
0
3.4
2.6
1.9
--0
1.7
0
0
0
0
2.3
2.6
2.5
0
~
~
~
P7754SCDT2
DVD Main 1/3 Schematic Diagram < DVD Section >
1-11-15
P7754SCD1
DVD Main 2/3 Schematic Diagram < DVD Section >
1-11-16
P7754SCD2
DVD Main 3/3 Schematic Diagram < DVD Section >
1-11-17
P7754SCD3
Sensor CBA Top View
Main CBA Top View < TV/VCR Section >
4A 125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
BHF300F01011A
BHF300F01011B
TO SENSOR CBA
(END-SENSOR)
VR1601
+B ADJ
WF2
PIN 49
OF IC1401
WF4
PIN 32
OF IC1401
WF7
PIN 10
OF IC1401
WF8
PIN 9
OF IC1401
WF6
TP1403
ENV.
WF5
TP1401
V-OUT
WF1
TP1402
RF-SW
WF3
TP1202
CTL-AMP
-OUT
TO SENSOR CBA
(START-SENSOR)
1-11-18
BP7750F01011
Main CBA Bottom View < TV/VCR Section >
4A 125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
WF16
PIN 59
OF IC1201
WF15
PIN 58
OF IC1201
1-11-19
BP7750F01011
Sub CBA Top View < TV/VCR Section >
TP2501
+B
TP1301
BLUE
TP2504
GND
R2583
(H f0 Adjustment)
1-11-20
BP7750F01021-A
Sub CBA Bottom View < TV/VCR Section >
WF17
PIN 8
OF CN2
WF18
PIN 6
OF CN2
WF20
PIN 1
OF CN2
WF19
PIN 4
OF CN2
WF9
TP2503
H-DRIVE
WF11
PIN 5
OF CN2571
WF10
Q2571
Collector
1-11-21
BP7750F01021-A
CRT CBA Top View < TV/VCR Section >
CRT CBA Bottom View < TV/VCR Section >
WF14
Q2501
Collector
1-11-22
WF13
Q2502
Collector
WF12
Q2503
Collector
BP7750F01021-B
Function CBA Top View < TV/VCR Section >
Junction-A CBA
Top View
< TV/VCR Section >
Junction-A CBA
Bottom View
< TV/VCR Section >
BP7750F01021-D
Junction-B CBA
Top View
< TV/VCR Section >
Junction-B CBA
Bottom View
< TV/VCR Section >
Function CBA Bottom View < TV/VCR Section >
BP7750F01021-E
BP7750F01021-C
1-11-23
Upper: WF6
Lower: WF1
1DIV: 0.2V 2DIV: 5V 5ms
TP1403 ENV. TP1402 RF-SW
WF7 1DIV: 0.5V 0.5ms
IC1401 PIN10
WF8 1DIV: 0.5V 0.5ms
IC1401 PIN9
WF3 1DIV: 1V 10ms
TP1202 CTL-AMP-OUT
WF4 1DIV: 0.25V 20 µs
IC1401 Pin 32
WF5 1DIV: 0.5V 20 µs
TP1401 V-OUT
WF2 1DIV: 0.2V 0.1µs
IC1401 Pin 49
WF1 1DIV: 2V 5ms
TP1402 RF-SW
1-12-1
WF16 1DIV: 1V 5ms
IC1201 PIN 59
1V
0.1µsec
WF20 1DIV: 1V 0.1µs
CN2 PIN 1
SPDIF
WF19 1DIV: 0.5V 0.5ms
CN2 PIN 4
WF15 1DIV: 1V 20 µs
IC1201 PIN 58
WF11 1DIV: 10V 5ms
CN2571 PIN 5
WF12 1DIV: 20V 20µs
Q2503 COLLECTOR
WF18 1DIV: 0.2V 20µs
CN2 PIN 6
WF17 1DIV: 0.2V 20µs
CN2 PIN 8
WF14 1DIV: 20V 20µs
Q2501 COLLECTOR
WF13 1DIV: 20V 20µs
Q2502 COLLECTOR
WF10 1DIV: 200V 20 µs
Q2571 COLLECTOR
WF9 1DIV: 2V 20 µs
TP2503 H-DRIVE
NTSC Color Bar Signal (with 1kHz Audio Signal) --- WF1~WF16
DVD Video (Power on (Stop) MODE) --- WF17, WF18
CD (1KHz Play) --- WF19, WF20
INITIAL POSITION: Unplug unit from AC outlet for at least five minutes,
reconnect to AC outlet and then turn power on.
(Brightness---Center Color---Center Tint---Center Contrast---Approx 70%)
Input:
WAVEFORMS
X8TWF
M
M
FULL
ERASE HEAD
FE HEAD
ACE HEAD ASSEMBLY
CONTROL
HEAD
AUDIO HEAD
AUDIO ERASE
HEAD
CYLINDER
ASSEMBLY
VIDEO
(R)-1
HEAD
VIDEO
(L)-1
HEAD
VIDEO
(L)-2
HEAD
VIDEO
(R)-2
HEAD
Hi-FiAUDIO(R)
HEAD
Hi-FiAUDIO(L)
HEAD
DRUM
MOTOR
PG
SENSOR
LOADING
MOTOR
CAPSTAN
MOTOR
CN1104
1
2
3
4
5
6
7
CN1802
1
2
3
4
SP(L)
GND
SP(L)
NU
KEY-1
NU
GND
SP(R)
SP(R)
SP-GND
SP-GND
CN1601
CN601A
CN601B
CN101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
FUNCTION
CBA
CN2401
1
CN2801
2
1
3
2
3
4
5
4
6
7
JUNCTION-A
CBA
JUNCTION-B
CBA
NU
DTV-ON-H2
D-GND
DTV-ON+3.3V
DTV-ON+2.5V
DTV-ON+1.8V
SMART-ANT(NU)
A-GND
DIF-AGC
A-GND
DIF-OUT1
DIF-OUT2
A-GND
DTV-VIDEO
DTV-AUDIO(L)
DTV-AUDIO(R)
A-GND
DTV-Y
DTV-Cr
DTV-Cb
W1601
SP801
SPEAKER
L-CH
SENSOR CBA
(END-SENSOR)
SENSOR CBA
(ST-SENSOR)
CN3801
1
CL3801
2
SP(L)
1
3
SP-GND 2
4
SP1801
SPEAKER
R-CH
CN102
1
2
3
4
5
6
7
8
9
10
DTV MODULE CBA UNIT
11
12
13
14
15
16
17
18
19
20
SP(L)
SP(L)
SP-GND
SP-GND
CN3802
1
CL3802
2
SP(R)
1
3
SP-GND 2
4
CL1401
Hi-Fi-AUDIO(L)
Hi-Fi-COM
Hi-Fi-AUDIO(R)
VIDEO(R)-2
VIDEO-COM2 CN1101
VIDEO(L)-2
1 D-GND
VIDEO(L)-1
2 DTV-SPDIF
VIDEO-COM1
3 DTV-ON+5V
VIDEO(R)-1
4 TU-SCL
5 TU-SDA
6 D-GND
7 DTV-S-SREQ
8 DTV-S-SCLK
9 DTV-S-SIN
10 DTV-S-SOUT
CL1402
11 D-GND
12 DTV-S-RESET
AE-H
13 D-GND
FE-H
14 SDA
AUDIO-COM
15 SCL
AUDIO-PB/REC
CTL(+)
CTL(-)
CL1403
1 FE-H
2 FE-H-GND
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
10
11
12
CL1201
CM+12V
P-ON+5V(3)
C-FG
CM-F/R
C-CONT
FG-GND
LD-CONT
D-CONT
D-PFG
M-GND
D/L+12V
VG+15V
MAIN CBA
CN1302
1
2
3
4
5
6
7
8
9
10
11
12
CN1102
13
1
14
2
15
3
16
4
17
5
18
6
19
7
CN1103
8
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
16
9
17
10
18
11
19
12
20
13
14
15
16
17
18
19
CN1301
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CN2301
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
+B
+B
GND
GND
GND
DEF+B
GND
GND
GND
DVD+9V
GND
DVD+5V
GND
GND
P-SAFETY1
P-SAFETY2
C-SYNC
P-ON+5V(2)
EV+4V
CN2103
1
2
3
4
5
6
7
8
9
10
11
12 CL2504A
13
1
14
2
15
3
16
4
17
5
18
19
CN2302
+5.7V-CTRL
1
DVD-MAIN-POWER 2
EXT-VIDEO
3
GND
4
VIDEO
5
GND
6
C-VIDEO
7
GND
8
DTV-Y
9
DTV-Cb
10
DTV-Cr
11
GND
12
DTV-SPDIF
13
GND
14
FSC
15
GND
16
TV-VIDEO
17
GND
18
GND
19
SDA
SCL
OSD-BLK
OSD-R
OSD-G
OSD-B
V-SYNC
H-SYNC
SPOT-KILL
NU
P-SAFETY3
DVD-REMOTE
DVD-SDATA
DVD-SCLK
DVD-CS
DVD-AUDIO-MUTE
DVD-AUDIO(L)
P-ON+8V
DVD-AUDIO(R)
P-ON+8V(1)
RED
GREEN
BLUE
GND
SCREEN
T2571
FBT
SUB CBA
CL2501A
CN2571
1
2
3
4
5
CN1
EV+1.2V
EV+1.2V
EV+1.2V
GND
GND
GND
GND
GND
EV+3.3V
EV+3.3V
DVD-ON+3.3V
DVD-ON+5V
EV+9V
EV+9V
PWRCON
DVD-SCLK
DVD-CS
DVD-SDATA
DVD-REMOTE
CL2504B
1
2
3
4
5
L551
D.Y.
GND
ANODE
FOCUS
CN2501
CRT CBA
CL2501B
VD
HD
1
2
CONTINUE
3
WIRING DIAGRAM
4
<DVD SECTION>
5
6
7
8 TO CN1A
9
10
11
12
13
14
15
16
17
18
19
CN2
1
DVD-SPDIF
2
GND
DVD-AUDIO(R) 3
DVD-AUDIO(L) 4
TO CN2A
5
GND
6
DVD-C
7
GND
8
DVD-Y
DVD-AUDIO-MUTE 9
10
NU
1
2
3
1-13-1
1 HEATER
2 GND
3 +180V
WIRING DIAGRAM FOR
DECK MECHANISM SECTION
WIRING DIAGRAM < TV/VCR Section >
P7754WIT
SLED
MOTOR
SPINDLE
MOTOR
DVD MECHANISM
M
M
1-13-2
PICK UP UNIT
DETECTOR
7
9
11
2
3
6
5
4
DRIVE CBA
TRAY-IN
TS
FS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
6
5
4
3
2
1
CN201
TS(+)
FS(+)
FS(-)
TS(-)
GND(CD-PD)
GND(DVD-PD)
PD-MONI
DVD-LD
GND(LD)
CD-LD
GND
NU
VREF
NU
B
C
A
D
CD/DVD
P-ON+5V
CN301
SP(+)
SP(-)
GND
SL(-)
SL(+)
TRAY-IN
DVD MAIN CBA UNIT
CN2A
DVD-SPDIF
GND
DVD-AUDIO(R)
DVD-AUDIO(L)
GND
DVD-C
GND
DVD-Y
DVD-AUDIO-MUTE
NU
CN1A
EV+1.2V
EV+1.2V
EV+1.2V
GND
GND
GND
GND
GND
EV+3.3V
EV+3.3V
DVD-ON+3.3V
DVD-ON+5V
EV+9V
EV+9V
PWRCON
DVD-SCLK
DVD-CS
DVD-SDATA
DVD-REMOTE
1
2
3
4
5 TO CN2
6
7
8
9
10
2
3
4
5
6
7
8
9
10 TO CN1
11
12
13
14
15
16
17
18
19
1
CONTINUE
WIRING DIAGRAM
<TV/VCR SECTION>
WIRING DIAGRAM < DVD Section >
P7754WID
SYSTEM CONTROL TIMING CHARTS
< TV/VCR Section >
Mode SW: LD-SW
LD-SW Position detection
A/D Input voltage Limit
(Calculated voltage)
Symbol
3.76 V ~ 4.50 V (4.12 V)
EJ
4.51 V ~ 5.00 V (5.00 V)
CL
0.00 V ~ 0.25 V (0.00 V)
SB
1.06 V ~ 1.50 V (1.21 V)
TL
0.66 V ~ 1.05 V (0.91 V)
FB
1.99 V ~ 2.60 V (2.17 V)
SF
1.51 V ~ 1.98 V (1.80 V)
SM
3.20 V ~ 3.75 V (3.40 V)
AU
0.26 V ~ 0.65 V (0.44 V)
AL
4.51 V ~ 5.00 V (5.00 V)
SS
2.61 V ~ 3.19 V (2.97 V)
RS
Note:
Note: EJ
RS: Loading FWD (LM-FWD / REV “H”)
RS
EJ: Loading REV (LM-FWD / REV “L”)
Stop (A) = Loading
Stop (B) = Unloading
Note:
Symbol
Loading Status
EJ
Eject
CL
Eject ~ REW Reel
SB
REW Reel ~ Stop (B)
TL
Stop (B) ~ Brake Cancel
FB
Brake Cancel ~ FF / REW
SF
FF / REW ~ Stop (M), (FF / REW)
SM
Stop (M), (FF / REW) ~ Stop (A)
AU
Stop (A) ~ Play / REC
AL
Play / REC ~ Still / Slow
SS
Still / Slow ~ RS (REW Search)
RS
RS (REW Search)
1-14-1
X8T4HTI
Chart 1
1) SP MODE
18 RF-SW
The first rise of RF-SW after a rise in F-AD signal.
F-AD
( Internal Signal )
AT
"H"
"H"
"Z"
T1
C-DRIVE
T2
Stop Detection
ST
Acceleration Detection
Slow Tracking Value
PB CTL
BL
Reversal Limit Value
66 C-F/R
ROLL
COMPENSATION
(DRUM SERVO)
1
2
3
4
H-A-SW
15 ROTA
STILL
FRAME ADVANCE
1-14-2
STILL
X8T4HTI
Chart 2
2) LP/EP MODE
18 RF-SW
The first rise of RF-SW after a rise in F-AD signal.
F-AD
( Internal Signal )
AT
"H"
"H"
"Z"
T1
C-DRIVE
T2
Stop Detection
ST
Acceleration Detection
Slow Tracking Value
PB CTL
BL
Reversal Limit Value
66 C-F/R
ROLL
COMPENSATION
(DRUM SERVO)
1
2
3
4
H-A-SW
15 ROTA
STILL
FRAME ADVANCE
1-14-3
STILL
X8T4HTI
Chart 3
EJ
POWER
-OFF
0.2S
ST-S/
END-S
"OFF"
CASS.LOAD
CL SB
LD-FWD
0.2S
SB
0.2S
STOP(B)
+100mS(NTSC)
+620mS(PAL)
TL
0.2S
LD-FWD
1.2S
0.2S
POWER
FB
TL
0.2S
STOP
0.4S
SM
SF
0.2S
0.2S
0.2S
LD-FWD
SF SM AL
AU
LD-REV
0.5S
SM
40mS
0.4S
AU
LD-REV
20mS
0.2S
STOP(A)
AL
AU
0.2S
0.2S
PLAY
0.8S
0.3S
PLAY
SS
LD-FWD
REW
RS
RS
0.3S
RS1(RS2)
0.2S
AL
SS AU
LD-REV
FF
FS
LD-FWD
AL
1.0S
FS1(FS2)
PLAY
PLAY
PLAY
STILL
(SLOW)
SS
AL
LD-REV
PLAY
AU
0.2S
0.5S
LD-FWD
PLAY
Refer to STILL/
SLOW TIMING
CHART 1, 2.
STILL(SLOW)
AL
STOP(A)
STOP
1.2S
40mS
AU SM
0.4S
STOP
/EJECT
0.12S
0.3S
PLAY
1. EJECT (POWER OFF) -> CASSETTE IN (POWER ON) -> STOP(B) -> STOP(A) -> PLAY -> RS -> FS -> PLAY -> STILL/SLOW -> PLAY -> STOP(A)
PIN NO.
1
LD-SW
CL/SS
EJ
AU
RS
SF
SM
TL
FB
AL
SB
82
LD-CONT
ON
ON
"Z"
C-DRIVE
66 C-F/R
DRUM
ROTATION
31 P-ON-H
65
AUDIO-MUTE
D-PB-H
44 D-REC-H
DISPLAY
LD-REV
PAUSE
(SLOW)
LD-FWD
PLAY
LD-FWD
REC
SFT-SW
LD-REV
0.2S
20mS
X8T4HTI
1-14-4
EJECT
Chart 4
SM
FB SM
SF
LD-FWD
FF
SF
REV
1.0S
AU SM
STOP
0.4S
LD-REV
40mS
SM AL
AU
0.5S
LD-FWD
STOP(A)
LD-REV
SF TL
FB
REW
20mS
0.2S
0.2S
FB SM
SF
LD-FWD
REW
SF
LD-FWD
LD-REV
40mS
0.4S
SM AL AU SM
AU
0.5S
STOP
0.2S
STOP(A)
REC
AU
AL
0.2S
1.0S
20mS
LD-FWD
REC
LD-FWD
SS RS
2.5S Short REV
LD-REV
AL AU
SS
0.2S
REC PAUSE
LD-FWD
AL
1.2S
1.5S
SS RS
REC PAUSE REC or
PAUSE
REC
STOP
/EJECT
LD-FWD
REC
LD-REV
AU SM
1.5S(NTSC)
1.0S(PAL)
0.4S
AL
0.2S
LD-FWD
0.5S
AL AU
SS
LD-REV
40mS
LD-REV
20mS
SB
0.2S
LD-REV
FB TL
SF
STOP
/EJECT
0.2S
STOP(A)
STOP
0.5S
0.2S
0.5S
0.1S
CL EJ
EJECT
ST-S
"ON"
CASS. UNLD
STOP
/EJECT
0.2S
REW
LD-REV
1.0S
STOP
/EJECT
0.2S
FF
SF TL
FB
0.2S
REC
PAUSE
2. STOP(A) -> FF -> STOP(A) -> REW -> STOP(A) -> REC -> PAUSE -> PAUSE or REC -> STOP(A) -> EJECT
PIN NO.
1
LD-SW
CL/SS
EJ
AU
RS
SF
SM
TL
FB
AL
SB
82
LD-CONT
ON
ON
"Z"
C-DRIVE
66 C-F/R
DRUM
ROTATION
31 P-ON-H
65
AUDIO-MUTE
D-PB-H
44 D-REC-H
DISPLAY
FF
LD-REV
X8T4HTI
1-14-5
STOP(A)
STOP
< DVD Section >
Tray Close ~ Play / Play ~ Tray Open
Tray
Close
Tray IN
(TL221)
Disc
Rotation
Play
Disc
Stop
Tray
Open
3.3V
0V
Sled Drive
(TP303)
1.65V
0V
Disc Drive
(TP301)
1.65V
0V
Focus Drive
(TP304)
1.65V
0V
Tracking Drive
(TP302)
1.65V
0V
1-14-6
X8T4HTI
IC PIN FUNCTION DESCRIPTIONS
IC1201 (TV/VCR Micro Controller IC)
Pin
No.
Signal Name
Pin
No.
Function
Signal Name
Function
33 REC-SAFETY
Record Protection Tab
Detection
1
LD-SW
Loading Switch Input
2
DVD-LED
DVD LED Control Output
34 RESET
System Reset Signal (Reset =
“L”)
3
P-SAFETY 2
Power Supply Failure
Detection 2
35 XC-IN
Sub Clock (32kHz)
36 XC-OUT
Sub Clock (32kHz)
4
ST/SAP-IN
Tuner Stereo/Sap Detector
Signal Input
37 TIMER+5V
VCC
5
KEY-0
Key Input 0
38 X-IN
Main Clock (10.6MHz)
6
KEY-1
Key Input 1
39 X-OUT
Main Clock (10.6MHz)
7
END-SENS
End-Sensor
40 GND
GND
8
AFT
AFT Voltage Input
41 SPOT-KILL
Counter Measure for Spot
9
ST-SENS
Start-Sensor
42
10 V-ENV
Video Envelope Input
11 VOLUME
Volume Control Signal Output
12 SP-MUTE
Speaker Mute Signal Output
13 DV-SYNC
Artificial Vertical Sync Output
14 REMOTE
Remote Control Signal Input
15 ROTA
Color Phase Rotary
Changeover Signal
16 V-H-SW
Video Head Amp Switching
Pulse
17 ENV-DET
DVD-MAINPOWER
Power On Signal at High for
DVD
43 CLKSEL
Clock Select (GND)
44 D-REC-H
Delayed Record Control Signal
45 I2C-OPEN
Chip Select
46 GND
GND
47
DVD-AUDIOMUTE
DVD Audio Mute Signal
48 DVD-H
DVD On Signal at High
49 GND
GND
Envelope Comparator Signal
50 DVD-CS
DVD Interface Chip Select
18 RF-SW
Video Head Switching Pulse
51 DVD-SCLK
DVD Interface Serial Clock
HiFi Audio Head Switching
Pulse
52 DVD-SDATA
DVD Interface Serial Data
19 Hi-Fi-H-SW
53 P-ON+5V
OSD VCC
D-REC
/PB-H
Delayed Record/Playback
Control Signal
54 HLF
Horizontal Filter
55 V-HOLD
Vertical Hold
56 CV-IN
Composite Video Signal Input
57 GND
GND
58 H-SYNC
Horizontal Sync Input
59 V-SYNC
Vertical Sync Input
60 OSD-BLK
Output for Picture Cut off
61 NU
Not Used
62 OSD-B
Blue Signal Output
63 OSD-G
Green Signal Output
64 OSD-R
Red Signal Output
65 DTV-S-SOUT
DTV Serial Data Output
20
21 REC-LED
REC LED Control Signal
22 NORMAL-H
Audio Mode Input Signal
23 NU
Not Used
24 AUDIO-MUTE
Audio Mute Signal Output
Remote Control Signal Output
25 DVD-REMOTE
to DVD
26 TV/VCR-LED
TV/VCR LED Control Signal
27 NU
Not Used
28 DTV-ON-H2
DTV On Signal 2 at High
D-REC
/PB-L
Delayed Record/Playback
Control Signal
29
30 DTV-ON-H
DTV On Signal at High
66 DTV-S-SIN
DTV Serial Data Input
31 P-ON-H
Power On Signal at High
67 DTV-S-SCLK
DTV Serial Clock
32 BUS-CONT
Bus Control
68 YCA-SDA
YCA Serial Data
69 YCA-CS
YCA Chip Select
1-15-1
P7752PIN
Pin
No.
Signal Name
Function
70 YCA-SCL
YCA Serial Clock
71 SCL
Serial Clock
72 SDA
Serial Data
73 C-F/R
Capstan Motor FWD/REV
Control Signal
74 C-SYNC
Composite Sync Input
75 P-ON-H2
Power On Signal at High
76 C-CONT
Capstan Motor Control Signal
77 D-CONT
Drum Motor Control Signal
78 P-SAFETY 3
Power Supply Failure
Detection 3
79 NU
Not Used
80 T-REEL
Take Up Reel Rotation Signal
81 DTV-S-RESET DTV Reset
82 LD-CONT
83
DIGITALAUDIO-H
Loading Motor Control Signal
Digital Audio Signal
84 P-DOWN
Power Voltage Down Detector
Signal
85 DTV-S-SREQ
DTV Serial Request
86 NU
Not Used
87 C-FG
Capstan Motor Rotation
Detection Pulse
88 GND
GND (AMP)
89 NU
Not Used
90 D-PFG
Drum Motor Pulse Generator
91 NU
Not Used
92 AMP-VREF-IN Standard Voltage Input
93 C
Ext. Capacitor Connection Port
for Analog Amp
94 CTL (-)
Record/Playback Control
Signal (-)
95 CTL (+)
Record/Playback Control
Signal (+)
96 AMPC
Amp Capacitor
97
CTL-AMPOUT
Control Amp Output
98 P-ON+5V
Power Supply for AMP
99 AL+5V
A/D, D/A Standard Voltage
100 P-SAFETY 1
Power Supply Failure
Detection 1
1-15-2
P7752PIN
LEAD IDENTIFICATIONS
2SK3563
2SK3757(Q)
MID-32A22F
2SA950-O(TE2 F T)
2SC2120-O(TE2 F T)
2SC1627-Y(TE2.F.T)
2SC2482
2SC3331(T)
2SD400(F)
KRA103M-AT/P
KRC103M-AT/P
KTA1267-GR-AT/P
KTC3199-GR-AT/P
KTC3199-Y-AT/P
C
G D S
E
E C B
AN17812A
LA78040A
1
E C B
2SC5885000RF
TLV1117IDCYRG3
16
9
1
8
1: GND
2: Vout
3: Vin
1 2
7
KIA7805API/P
3
B C E
KIA431-AT/P
M3776AMFH-BB1GP
1: IN
2: GND
3: OUT
1 2 3
51
80
LTV-817C-F
1
4 1: A
2
3 2: K
81
50
100
31
3: E
4: C
1: R
2: A
3: K
1 2 3
30
1
PQ070XF01SZH
M61116FP TF0G
11
20
1: Vin
2: Vo
3: GND
4: Vc
LA71205M-MPB-E
LA72670BM-MPB-E
AT24C128N-10SU-1.8S
M24C04-WMN6TP
60
41
1234
8
1
5
61
40
1
10
M61276FP TF0H
22
42
4
TC4053BF(EL N F)
9
16
21
80
1
1
20
1-16-1
21
1
8
Note:
A: Anode
K: Cathode
E: Emitter
C: Collector
B: Base
R: Reference
S: Source
G: Gate
D: Drain
P7753LE
EXPLODED VIEWS
Cabinet
SHINWHA
TAPE SGT-730
(BLACK)
Details for L551
and surrounding parts
V501-2
SHINWHA
TAPE SGT-730
(WHITE)
V501-1
L551
L1
TB5
B2
L5
Scotch
Tape #880
CLN551
L5
L1
DVD Mechanical Parts
CRT CBA
A3
A2
L2
L3-1
TL4
TL4
L5
L1
TL3
TB2
B2
1B2
B2
TL3
TL2
Scotch
Tape #880
L3-2
TL1-1
B1
TB11
DVD Main
CBA Unit
TL1-3
TL1-3
TL1-1
DG601
V501
A1-1
SP801
L5
TL1-4
L4
TL1-1
TL1-3
TL2
1B1
B2
Sub CBA
Sensor CBA
A1-5
A1-8
TB7
TL1-2
TB3
A1-7 A1-9
B6
W1601
TB8
DTV Module CBA Unit
A1-4
TL2
TB9
A1-6
B7
A1-3
A1-2
TL1-2
Function CBA
Junction-B CBA
A1X
L1
TB10
TL2
Main CBA
B6
SP1801
L4
Sensor CBA
TL1-2
TL5
See Electrical Parts List
for parts with this mark.
Junction-A CBA
TB1
1-17-1
P7752CEX
Packing
X3
X2
S2
S7
Packing Tape
Tape
S6
X1
S3
S4
FR
ON
T
S1
1-17-2
P7754PEX
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Ref. No.
A1X
Description
FRONT CABINET ASSEMBLY P7754UT
Ref. No.
Description
Part No.
S3
STYROFORM BOTTOM ASSEMBLY P7754UT
1ESA14156
S4
RFID LABEL P7100UM
----------
S6
SET SHEET B7500UA 1000X1700
0EM402178
S7
HOLD PAD T1100UA
1EM420618
ACCESSORIES
X1
BAG POLYETHYLENE 235X365XT0.03
0EM408420A
X2#
OWNERS MANUAL P7754UT
1EMN22130
X3
REMOTE CONTROL NF109UD 151/ECNX801/ NF109UD
NF109UD
Part No.
1EM121836
A1-1
FRONT CABINET T1202UC
1EM121335
A1-2
CONTROL PLATE P7754UT
1EM221549
A1-3
BADGE BRAND T7310UL ~MAGNAVOX~
0EM407275
A1-4
CASSETTE DOOR T1202UC
1EM422886
A1-5
SPRING DOOR T1200UA
1EM422903
A1-6
CLOTH(4X7XT0.7) T5000UA
0EM404974
A1-7
TRAY PANEL TD930JA
0EM301939A
A1-8
TRAY SPRING TD707UH
0EM408552
A1-9
CLOTH(B) L5201U0 15X10X1.0T
0EM400076
A2
REAR CABINET P7754UT
1EM121837
A3#
RATING LABEL P7754UT
----------
1B1
DECK ASSEMBLY CZD014/VM2466
N2466FT
1B2
DVD MECHA X7 TRIPLE N79U1KVM
N79U1KVM
B1
SPRING TENSION B0080B0 EM40808
26WH006
B2#
DEGAUSS HOLDER L2401UB
1EM420205
B6
CLOTH(10X30XT0.5) B5900UA
0EM404486
B7
CLOTH(15X10XT0.5) L9700UA
0EM405038
CLN551# CRT GND WIRE
WX1L7820-003
DG601#
DEGAUSSING COIL (AL) ZTM054A
LLBH00ZTM069
L1
SCREW P-TIGHT 4X18 BIND HEAD +
GBJP4180
L2
SCREW TAPPING M4X14
DBT14140
L3-1
SCREW P-TIGHT 3X10 BIND HEAD+
GBHP3100
L3-2
SCREW P-TIGHT 3X10 BIND HEAD+
GBHP3100
L4
SCREW P-TIGHT 3X10 BIND HEAD+
GBJP3100
L5
SCREW L1500UA
0EM406142A
L551#
DEFLECTION YOKE (PB FREE) CDYMM2102A1
LLBY00Z0X011
SP801
SPEAKER S0407F01A
DSD0807XQ001
SP1801
SPEAKER S0407F01A
DSD0807XQ001
TB1
TRAY CHASSIS T3220UA
1EM021069
TB2
TOP SHIELD T1100UA
1EM320155
TB5
LASER CAUTION LABEL T8200UA
----------
TB7
MODULE PCB HOLDER P7150UZ
1EM322373
TL1-1
SCREW P-TIGHT 3X12 WASHER HEAD+
GCJP3120
TL1-2
SCREW P-TIGHT 3X12 WASHER HEAD+
GCJP3120
TL1-3
SCREW P-TIGHT 3X12 WASHER HEAD+
GCJP3120
TL1-4
SCREW P-TIGHT 3X12 WASHER HEAD+
GCJP3120
TL2
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
TL3
SCREW S-TIGHT M3X4 BIND HEAD
GBJS3040
TL4
SCREW P-TIGHT 3X20 BIND HEAD +
GBJP3200
TL5
SCREW P-TIGHT M3X8 BIND HEAD+ BLK
GBHP3080
V501#
CRT A51LYW996X
TCRT190MS016
V501-1
C.P.MAGNET JH225-19C
XM04000BV016
V501-2
WEDGE FT-00110W
XV10000T4001
S1
CARTON P7754UT
1EM424234
S2
STYROFORM TOP ASSEMBLY P7754UT
1ESA14155
PACKING
20070131
1-18-1
P7754CA
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
DTV MODULE CBA UNIT
Ref. No.
Description
DTV MODULE CBA UNIT
Part No.
1ESA14071
DVD MAIN CBA UNIT
Ref. No.
Description
DVD MAIN CBA UNIT
Part No.
N7CT6KUP
MMA CBA
Ref. No.
Description
Part No.
MMA CBA
Consists of the following:
1ESA14051
MAIN CBA
SENSOR CBA
---------1ESA12193
MAIN CBA
Ref. No.
Description
MAIN CBA
Consists of the following:
C1008
ELECTROLYTIC CAP. 1µF/50V M
CERAMIC CAP.(AX) B K 1000pF/50V
Part No.
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
C1127
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
C1128
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C1129
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C1131
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZ30F103
C1203
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
C1206
CHIP CERAMIC CAP. F Z 0.047µF/50V
CHD1JZ30F473
C1207
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
C1208
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
C1210
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1212
CHIP CERAMIC CAP.(1608) CH J 22pF/50V
CHD1JJ3CH220
C1213
CHIP CERAMIC CAP.(1608) CH J 22pF/50V
CHD1JJ3CH220
C1214
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
C1217
CHIP CERAMIC CAP.(1608) CH D 10pF/50V
CHD1JD3CH100
C1218
CHIP CERAMIC CAP. CH J 15pF/50V
CHD1JJ3CH150
C1220
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
C1222
CHIP CERAMIC CAP. B K 2200pF/50V
CHD1JK30B222
C1223
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1224
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
C1225
CHIP CERAMIC CAP. CH J 560pF/50V
CHD1JJ3CH561
C1234
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C1235
CHIP CERAMIC CAP.(1608) B K 0.022µF/50V
CHD1JK30B223
C1239
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1240
CHIP CERAMIC CAP. CH J 560pF/50V
CHD1JJ3CH561
C1241
CHIP CERAMIC CAP.(1608) B K 4700pF/50V
CHD1JK30B472
C1243
ELECTROLYTIC CAP. 22µF/16V M LL
CE1CMASLH220
C1245
ELECTROLYTIC CAP. 47µF/6.3V M
CE0KMASDL470
C1247
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
C1251
CHIP CERAMIC CAP.(1608) B K 2700pF/50V
CHD1JK30B272
C1252
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASDL101
C1253
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C1254
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASDL470
C1264
CHIP CERAMIC CAP. F Z 0.047µF/50V
CHD1JZ30F473
C1299
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1410
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1411
ELECTROLYTIC CAP. 100µF/10V M H7
CE1AMAVSL101
C1413
CHIP CERAMIC CAP.(1608) CH J 390pF/50V
CHD1JJ3CH391
C1414
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
C1416
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1417
CHIP CERAMIC CAP. B K 220pF/50V
CHD1JK30B221
C1418
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
CE1JMASDL1R0
C1419
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
CCA1JKT0B102
C1420
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
Part No.
----------
CAPACITORS
C1006
Description
C1124
C1010
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C1421
C1030
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C1422
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1034
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
C1423
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1035
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1424
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
CE1CMAVSL220
C1037
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZ30F103
C1425
C1040
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C1426
ELECTROLYTIC CAP. 22µF/16V M H7
C1041
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1427
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1428
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
CE0KMAVSL470
C1043
FILM CAP.(P) 0.018µF/50V J
CMA1JJS00183
C1044
CHIP CERAMIC CAP.(1608) B K 0.047µF/50V
CHD1JK30B473
C1429
ELECTROLYTIC CAP. 47µF/6.3V M H7
C1045
CHIP CERAMIC CAP. CH D 3pF/50V
CHD1JD3CH3R0
C1430
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1046
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
C1431
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1049
CERAMIC CAP.(AX) CH K 2.7pF/50V
CCA1JKTCH2R7
C1432
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
C1050
CHIP CERAMIC CAP. CH D 6pF/50V
CHD1JD3CH6R0
C1435
C1121
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C1436
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1122
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C1437
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1123
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C1438
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1439
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
20070131
1-19-1
P7754EL
Ref. No.
Description
Ref. No.
Part No.
Description
Part No.
C1441
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
C1784
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
C1442
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C1786
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1443
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C1787
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1444
ELECTROLYTIC CAP. 100µF/6.3V H7
CE0KMAVSL101
C1788
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1452
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1789
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1463
CHIP CERAMIC CAP. CH J 820pF/25V
CHD1EJ3CH821
C1790
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1464
CHIP CERAMIC CAP.(1608) B K 2700pF/50V
CHD1JK30B272
C1791
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1465
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1792
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1466
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1793
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1468
ELECTROLYTIC CAP. 33µF/16V M H7
CE1CMAVSL330
C1794
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1469
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1795
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1602
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
C1797
ELECTROLYTIC CAP. 100µF/10V M H7
CE1AMAVSL101
C1604#
METALIZED FILM CAP. 0.1µF/250V
CT2E104MS037
C1801
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASDL221
CHD1JK30B472
C1605#
METALIZED FILM CAP. 0.22µF/250V
CT2E224MS037
C1803
CHIP CERAMIC CAP.(1608) B K 4700pF/50V
C1610
ELECTROLYTIC CAP. 470µF/200V LX
CA2D471S6017
C1804
CHIP CERAMIC CAP.(1608) B K 4700pF/50V
CHD1JK30B472
C1611
CERAMIC CAP. 680pF/2KV
CA3D681PAN04
C1807
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASDL221
CHD1AZ30F105
C1612
FILM CAP.(P) 0.033µF/50V J
CMA1JJS00333
C1811
CHIP CERAMIC CAP. F Z 1µF/10V
C1613
FILM CAP.(P) 0.0015µF/50V J
CMA1JJS00152
C1813
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1614#
FILM CAP.(P) 0.082µF/50V J
CMA1JJS00823
C1814
ELECTROLYTIC CAP. 2.2µF/50V M H7
CE1JMAVSL2R2
C1615
CERAMIC CAP. 560pF/2KV
CA3D561PAN04
C1815
ELECTROLYTIC CAP. 47µF/16V M H7
CE1CMAVSL470
C1616
ELECTROLYTIC CAP. 100µF/160V M
CE2CMZPDL101
C1818
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1617#
ELECTROLYTIC CAP. 470µF/35V M
CE1GMASDL471
C1819
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1618
ELECTROLYTIC CAP. 1000µF/10V M
CE1AMASDL102
C1821
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASDL471
C1619
ELECTROLYTIC CAP. 1000µF/16V M
CE1CMZPDL102
C1850
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1621
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
C1851
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1630#
SAFETY CAP. 4700pF/250V KX
CA2E472MR050
C1852
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1651
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
C1853
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1652
FILM CAP.(P) 0.0047µF/50V J
CMA1JJS00472
C1855
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1653
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
C1856
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
C1671
CERAMIC CAP. B K 2200pF/500V
CCD2JKS0B222
C1870
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
C1688
ELECTROLYTIC CAP. 10µF/16V M H7
CE1CMAVSL100
C1871
ELECTROLYTIC CAP. 100µF/16V M H7
CE1CMAVSL101
C1689
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASDL470
C1872
CERAMIC CAP. B K 470pF/100V
CCD2AKS0B471
C1740
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
C1873
FILM CAP.(P) 0.018µF/100V J
CMA2AJS00183
C1747
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1901
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
C1748
CHIP CERAMIC CAP.(1608) B K 0.047µF/50V
CHD1JK30B473
C1903
ELECTROLYTIC CAP. 1000µF/10V M
CE1AMASDL102
C1752
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1904
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
C1753
ELECTROLYTIC CAP. 10µF/25V M H7
CE1EMAVSL100
C1905
ELECTROLYTIC CAP. 2.2µF/250V M
CA2E2R2S6009
C1754
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1906
CERAMIC CAP. B K 330pF/500V
CCD2JKS0B331
C1755
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1907
FILM CAP.(P) 0.0015µF/50V J
CMA1JJS00152
C1756
ELECTROLYTIC CAP. 10µF/25V M H7
CE1EMAVSL100
C1908
FILM CAP.(P) 0.018µF/50V J
CMA1JJS00183
C1757
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C1909
CERAMIC CAP.(AX) X M 4700pF/16V
CCA1CMT0X472
C1758
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1910
ELECTROLYTIC CAP. 1000µF/16V M
CE1CMZPDL102
C1759
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C1912
ELECTROLYTIC CAP. 47µF/16V M
CE1CMASDL470
C1760
CHIP CERAMIC CAP.(1608) B K 4700pF/50V
CHD1JK30B472
C1762
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
CN601A
TERMINAL PRINTBORD PIN MS-PIN155155
C1763
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
CN601B
TERMINAL PRINTBORD PIN MS-PIN155155
JTEA001CHY01
C1764
ELECTROLYTIC CAP. 100µF/6.3V H7
CE0KMAVSL101
CN1103
JCTWA19TG004
C1766
ELECTROLYTIC CAP. 2.2µF/50V M H7
CE1JMAVSL2R2
BOARD CONNECTOR 19P(PB FREE)
127301119K2
C1769
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
CN1104
TWG CONNECTOR 07P TWG-P07P-A1
J3TWA07TG001
C1770
CHIP CERAMIC CAP.(1608) B K 4700pF/50V
CHD1JK30B472
CN1301
BOARD CONNECTOR 19P(PB FREE)
127301119K2
JCTWA19TG004
CN1302
BOARD CONNECTOR 19P(PB FREE)
127301119K2
JCTWA19TG004
CN1802
242 SERIES CONNECTOR 224202104W1
J322C04TG001
C1771
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C1772
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
CONNECTORS
JTEA001CHY01
C1773
ELECTROLYTIC CAP. 10µF/25V M H7
CE1EMAVSL100
C1774
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C1775
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D1105
ZENER DIODE MTZJT-775.6C
QDTC0MTZJ5R6
C1776
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D1108
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1777
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D1109
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1778
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D1110
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1779
ELECTROLYTIC CAP. 2.2µF/50V M H7
CE1JMAVSL2R2
D1111
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1780
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
D1112
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1781
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D1113
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C1782
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
D1204
LED LTL-4214M1
NPQZLTL4214M
C1783
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
20070131
DIODES
1-19-2
P7754EL
Ref. No.
Description
Part No.
Ref. No.
Description
NPWZ3GTF4550
IC1601#
PHOTOCOUPLER LTV-817C-F
LED LTL-4214M1
NPQZLTL4214M
IC1682#
IC VOLTAGE REGULATOR 5V KIA7805API/P
NSZBA0SJY041
LED SIR-563ST3F P
QPQPS1R563ST
IC1701
IC HIFI LA72670BM-MPB-E
QSZBA0RSY039
D1229#
ZENER DIODE MTZJT-7715B
QDTB00MTZJ15
IC1803
IC AN17812A
QSZBA0SMS017
D1230#
ZENER DIODE MTZJT-7715B
QDTB00MTZJ15
IC1850
IC SWITCH TC4053BF(EL N F)
QSZBA0TTS163
D1216
LED LAMP 333GT/F45-50
D1217
D1224
Part No.
NPEC0LTV817F
D1231
ZENER DIODE MTZJT-7718A
QDTA00MTZJ18
IC1901#
PHOTOCOUPLER LTV-817C-F
NPEC0LTV817F
D1238
ZENER DIODE MTZJT-775.6B
QDTB0MTZJ5R6
IC1902#
PHOTOCOUPLER LTV-817C-F
NPEC0LTV817F
D1419
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D1420
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
L1001
CHIP RES.(1608) 1/10W 0 Ω
D1603#
DIODE 1N5406
NDLZ001N5406
L1002
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
D1604#
DIODE 1N5406
NDLZ001N5406
L1005
PCB JUMPER D0.6-P5.0
JW5.0T
D1605#
DIODE 1N5406
NDLZ001N5406
L1006
PCB JUMPER D0.6-P5.0
JW5.0T
D1606#
DIODE 1N5406
NDLZ001N5406
L1031
PCB JUMPER D0.6-P5.0
JW5.0T
D1607#
ZENER DIODE MTZJT-7724C
QDTC00MTZJ24
L1032
PCB JUMPER D0.6-P5.0
JW5.0T
D1609
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
L1033
INDUCTOR 150µH-J-26T
LLAXJATTU151
D1610
ZENER DIODE MTZJT-775.6B
QDTB0MTZJ5R6
L1112
PCB JUMPER D0.6-P5.0
JW5.0T
D1611
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
L1202
INDUCTOR 0.10µH-K-26T
LLAXKATTUR10
D1613#
RECOVERY DIODE ERC18-04
QDZZ0ERC1804
L1601#
LINE FILTER JLB20102
LLEG0Z0XB006
D1614#
DIODE FR104-B
NDLZ000FR104
L1872
INDUCTOR 47µH-K-5FT
LLARKBSTU470
D1615#
RECTIFIER DIODE 1N4005
NDQZ001N4005
D1616#
FAST RECOVERY DIODE FR202
NDWZ000FR202
Q1103
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1617#
SCHOTTKY BARRIER DIODE SB270-B/P
NDWZ000SB270
Q1104
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
D1620#
ZENER DIODE MTZJT-776.8B
QDTB0MTZJ6R8
Q1105
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1621
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1106
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1622#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1107
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1623#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1108
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1624#
SCHOTTKY BARRIER DIODE SB240-B/P
NDQZ000SB240
Q1109
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1626
ZENER DIODE MTZJT-7733B
QDTB00MTZJ33
Q1110
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1627#
ZENER DIODE MTZJT-7716B
QDTB00MTZJ16
Q1112
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1628#
SCHOTTKY BARRIER DIODE SB240-B/P
NDQZ000SB240
Q1113
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1634
ZENER DIODE MTZJT-779.1B
QDTB0MTZJ9R1
Q1205
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1635
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1206
PHOTO TRANSISTOR MID-32A22F
NPWZ1D32A22F
D1636#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1207
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
COILS
RRXAJR5Z0000
TRANSISTORS
D1637
DIODE FR104-B
NDLZ000FR104
Q1208
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1640#
DIODE 1ZC36(Q)
QDLZ001ZC36Q
Q1209
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1641#
ZENER DIODE MTZJT-7739B
QDTB00MTZJ39
Q1210
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1645#
SCHOTTKY BARRIER DIODE SB140
NDWZ000SB140
Q1221
RES. BUILT-IN TRANSISTOR KRA103M-AT/P
NQSZ0KRA103M
D1682
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1401
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
D1683
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1402
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
D1685#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1403
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
D1687#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1404
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1692
PCB JUMPER D0.6-P5.0
JW5.0T
Q1601#
MOS FET 2SK3563
QFWZ02SK3563
D1811#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1602#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1901#
DIODE FR104-B
NDLZ000FR104
Q1604#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1902#
DIODE FR154
NDLZ000FR154
Q1605
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1903#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1607#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1904#
SCHOTTKY BARRIER DIODE SB140
NDWZ000SB140
Q1613#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1905
ZENER DIODE MTZJT-776.2C
QDTC0MTZJ6R2
Q1614#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1906#
ZENER DIODE MTZJT-7739B
QDTB00MTZJ39
Q1681#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1907#
ZENER DIODE MTZJT-776.8B
QDTB0MTZJ6R8
Q1688#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1908
RECTIFIER DIODE BA158
NDQZ000BA158
Q1689#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D1909
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
Q1701
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
D1910#
ZENER DIODE MTZJT-7715B
QDTB00MTZJ15
Q1850
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
Q1871
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
ICS
IC1001
IC VIF/SIF M61116FP TF0G
QSZBA0SHT034
Q1872
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
IC1101
VOLTAGE REGULATOR PQ070XF01SZH
QSZBA0SSH054
Q1873
TRANSISTOR 2SC3331(T)
QSC3331TNPAA
IC1104
IC EEPROM AT24C128N-10SU-1.8 S
NSZBA0TAZ083
Q1874
TRANSISTOR 2SC3331(T)
QSC3331TNPAA
IC1105
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
Q1875
RES. BUILT-IN TRANSISTOR KRA103M-AT/P
NQSZ0KRA103M
IC1106
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
Q1901
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
IC1201#
MICRO COMPUTER M3776AMFH-BB1GP
QSZAA0RHT160
Q1902#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
IC1202
IC(EEP-ROM) M24C04-WMN6TP
NSZAA0TSS015
Q1903#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
IC1401
IC Y/C/A LA71205M-MPB-E
QSZBA0RSY037
Q1904#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
20070131
1-19-3
P7754EL
Ref. No.
Description
Ref. No.
Part No.
Part No.
RRXAFR5H1500
R1173
CHIP RES. 1/10W F 4.7k Ω
RRXAFR5H4701
R1174
CARBON RES. 1/4W J 390 Ω
RCX4JATZ0391
R1175
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R1176
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
FET 2SK3757(Q)
QFWZ02SK3757
R1172
Q1906
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
Q1907#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
Q1908#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
RESISTORS
Description
CHIP RES. 1/10W F 150 Ω
Q1905#
R1001
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R1177
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R1002
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R1178
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R1004
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1179
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1005
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1180
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1031
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1200
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1032
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R1201
CHIP RES. 1/10W F 4.7k Ω
RRXAFR5H4701
R1033
CHIP RES. 1/10W J 390k Ω
RRXAJR5Z0394
R1202
CHIP RES. 1/10W F 22k Ω
RRXAFR5H2202
R1034
CHIP RES. 1/10W J 1.8k Ω
RRXAJR5Z0182
R1203
CHIP RES. 1/10W F 470 Ω
RRXAFR5H4700
R1037
CHIP RES. 1/10W J 180 Ω
RRXAJR5Z0181
R1204
CHIP RES. 1/10W F 1.5k Ω
RRXAFR5H1501
R1038
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1205
CHIP RES. 1/10W F 3.6k Ω
RRXAFR5H3601
R1039
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1206
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
R1040
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1208#
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1041
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
R1209
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1042
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R1210
CHIP RES. 1/10W F 15k Ω
RRXAFR5H1502
R1043
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1211
CHIP RES. 1/10W F 6.8k Ω
RRXAFR5H6801
R1049
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1212
CHIP RES. 1/10W F 4.7k Ω
RRXAFR5H4701
R1050
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1213
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1109
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1214
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1120
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
R1215
CHIP RES. 1/10W F 1.5k Ω
RRXAFR5H1501
R1121
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1216
CHIP RES. 1/10W F 1.5k Ω
RRXAFR5H1501
R1122
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1217
CHIP RES. 1/10W F 2.2k Ω
RRXAFR5H2201
R1123
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1218
CHIP RES. 1/10W F 2.7k Ω
RRXAFR5H2701
R1124
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1219
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1126
CHIP RES. 1/10W J 820 Ω
RRXAJR5Z0821
R1220
CHIP RES. 1/10W J 390k Ω
RRXAJR5Z0394
R1127
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1221
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R1128
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1222
CHIP RES. 1/10W J 390k Ω
RRXAJR5Z0394
R1129
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1224
CHIP RES. 1/10W J 680 Ω
RRXAJR5Z0681
R1130
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1225
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R1131
METAL OXIDE FILM RES. 1W J 8.2 Ω
RN018R2ZU001
R1226
CHIP RES. 1/10W J 27k Ω
RRXAJR5Z0273
R1140
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1227
CHIP RES. 1/10W J 270 Ω
RRXAJR5Z0271
R1141
CHIP RES. 1/10W J 56k Ω
RRXAJR5Z0563
R1228
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1143
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R1229
CHIP RES. 1/10W J 680 Ω
RRXAJR5Z0681
R1145
CARBON RES. 1/4W J 12 Ω
RCX4JATZ0120
R1230
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1146
CARBON RES. 1/4W J 2.7 Ω
RCX4JATZ02R7
R1231
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1147
CARBON RES. 1/4W J 12 Ω
RCX4JATZ0120
R1232
CHIP RES. 1/10W J 6.8k Ω
RRXAJR5Z0682
R1148
CARBON RES. 1/4W J 2.2 Ω
RCX4JATZ02R2
R1233
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1149
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R1234
CHIP RES. 1/10W J 1.2k Ω
RRXAJR5Z0122
R1150
CARBON RES. 1/4W J 2.2 Ω
RCX4JATZ02R2
R1235
CHIP RES. 1/10W J 47 Ω
RRXAJR5Z0470
R1151
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1236
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1152
CHIP RES. 1/10W F 22k Ω
RRXAFR5H2202
R1237
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1153
CHIP RES. 1/10W F 220 Ω
RRXAFR5H2200
R1238
CHIP RES. 1/10W J 470k Ω
RRXAJR5Z0474
R1154
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R1239
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1155
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
R1240
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1156
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1241
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1157
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R1242
CHIP RES. 1/10W J 33k Ω
RRXAJR5Z0333
R1158
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1243
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1159
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1244
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
R1160
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1245
CHIP RES. 1/10W J 470 Ω
RRXAJR5Z0471
R1161
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1246
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1162
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1247
CHIP RES. 1/10W J 820 Ω
RRXAJR5Z0821
R1164
METAL OXIDE FILM RES. 1W J 0.39 Ω
RN01R39ZU001
R1248
CHIP RES. 1/10W J 470 Ω
RRXAJR5Z0471
R1165
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1249
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R1166
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1250
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R1167
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
R1251
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R1168
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1252
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R1170
CHIP RES. 1/10W J 680 Ω
RRXAJR5Z0681
R1253
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R1171
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
R1254
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R1255
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
20070131
1-19-4
P7754EL
Ref. No.
R1257
Description
CHIP RES.(1608) 1/10W 0 Ω
Part No.
Ref. No.
Description
RRXAJR5Z0000
R1610
CARBON RES. 1/4W J 1.2k Ω
Part No.
RCX4JATZ0122
R1258
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1613
CARBON RES. 1/4W J 150 Ω
RCX4JATZ0151
R1259
CARBON RES. 1/4W J 1.2k Ω
RCX4JATZ0122
R1614
CARBON RES. 1/4W J 1.2k Ω
RCX4JATZ0122
R1260
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1617#
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R1261#
METAL OXIDE FILM RES. 2W J 2.2 Ω
RN022R2ZU001
R1618#
PCB JUMPER D0.6-P5.0
JW5.0T
R1262
CHIP RES. 1/10W J 680 Ω
RRXAJR5Z0681
R1619#
METAL OXIDE FILM RES. 1W J 2.2k Ω
RN01222ZU001
R1263
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R1620#
METAL OXIDE FILM RES. 1W J 2.2k Ω
RN01222ZU001
R1264
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1621
METAL OXIDE FILM RES. 1W J 4.7k Ω
RN01472ZU001
R1267
CHIP RES. 1/10W J 82k Ω
RRXAJR5Z0823
R1623#
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R1270
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1624#
CARBON RES. 1/4W G 47k Ω
RCX4GATZ0473
R1273
CHIP RES. 1/10W J 1.8k Ω
RRXAJR5Z0182
R1625#
CARBON RES. 1/4W G 39k Ω
RCX4GATZ0393
R1274
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R1629#
CARBON RES. 1/4W J 13k Ω
RCX4JATZ0133
R1277
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1630#
CARBON RES. 1/4W J 13k Ω
RCX4JATZ0133
R1280
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1631#
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R1283
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1632#
CARBON RES. 1/4W G 560 Ω
RCX4GATZ0561
R1284
CHIP RES. 1/10W J 220k Ω
RRXAJR5Z0224
R1633#
CARBON RES. 1/4W G 5.6k Ω
RCX4GATZ0562
R1285
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1634
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1286
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1635
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1287
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R1636#
METAL OXIDE FILM RES. 1W J 2.2k Ω
RN01222ZU001
R1289
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1637#
PCB JUMPER D0.6-P5.0
JW5.0T
R1290
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1639
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1291
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1640
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R1292
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1642#
CHIP RES. 1/10W J 6.8k Ω
RRXAJR5Z0682
R1293
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1644
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1294
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1650
METAL OXIDE FILM RES. 1W J 4.7k Ω
RN01472ZU001
R1298
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1654
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
R1299
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1655
CARBON RES. 1/4W J 2.7k Ω
RCX4JATZ0272
R1405
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1656
PCB JUMPER D0.6-P5.0
JW5.0T
R1406
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1657
CARBON RES. 1/4W J 2.7 Ω
RCX4JATZ02R7
R1407
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
R1662#
CARBON RES. 1/4W J 560k Ω
RCX4JATZ0564
R1408
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
R1663
CARBON RES. 1/4W J 560k Ω
RCX4JATZ0564
R1409
CHIP RES. 1/10W J 6.8k Ω
RRXAJR5Z0682
R1685
METAL OXIDE FILM RES. 1W J 8.2 Ω
RN018R2ZU001
R1410
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1686
CARBON RES. 1/4W J 150 Ω
RCX4JATZ0151
R1411
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R1687
CARBON RES. 1/4W J 150 Ω
RCX4JATZ0151
R1412
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1688
CARBON RES. 1/2W J 12 Ω
RCX2JZQZ0120
R1413
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1689
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
R1415
CHIP RES. 1/10W J 1.2k Ω
RRXAJR5Z0122
R1691
CARBON RES. 1/4W J 8.2 Ω
RCX4JATZ08R2
R1416
CHIP RES. 1/10W J 330k Ω
RRXAJR5Z0334
R1692
CARBON RES. 1/2W J 18 Ω
RCX2JZQZ0180
R1417
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R1693
CARBON RES. 1/2W J 18 Ω
RCX2JZQZ0180
R1418
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
R1694
CARBON RES. 1/4W J 1.5 Ω
RCX4JATZ01R5
R1419
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
R1701
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R1420
CHIP RES. 1/10W J 12k Ω
RRXAJR5Z0123
R1751
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1421
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1752
CHIP RES. 1/10W J 12k Ω
RRXAJR5Z0123
R1422
CHIP RES. 1/10W J 270 Ω
RRXAJR5Z0271
R1753
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1423
CHIP RES. 1/10W J 390 Ω
RRXAJR5Z0391
R1754
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1424
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1755
CHIP RES. 1/10W J 470 Ω
RRXAJR5Z0471
R1425
CHIP RES. 1/10W J 82k Ω
RRXAJR5Z0823
R1756
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1426
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1757
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1427
CHIP RES. 1/10W J 820 Ω
RRXAJR5Z0821
R1758
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1428
CHIP RES. 1/10W J 680k Ω
RRXAJR5Z0684
R1759
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1429
CHIP RES. 1/10W J 1.2k Ω
RRXAJR5Z0122
R1760
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1431
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1761
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1432
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1762
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1437
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1763
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1438
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1764
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1602#
CEMENT RES 5W K 1.2 Ω
RW051R2PG002
R1765
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1603#
METAL OXIDE FILM RES. 2W J 0.33 Ω
RN02R33ZU001
R1769
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1604
CARBON RES. 1/4W J 560k Ω
RCX4JATZ0564
R1772
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1605
CARBON RES. 1/4W J 560k Ω
RCX4JATZ0564
R1773
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1606
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R1774
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1607
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R1780
CHIP RES. 1/10W J 6.8k Ω
RRXAJR5Z0682
R1608
CARBON RES. 1/4W J 180k Ω
RCX4JATZ0184
R1781
CHIP RES. 1/10W J 8.2k Ω
RRXAJR5Z0822
R1609
CARBON RES. 1/4W J 10 Ω
RCX4JATZ0100
R1801#
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
20070131
1-19-5
P7754EL
Ref. No.
Description
Ref. No.
Part No.
Description
Part No.
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
SW1208
TACT SWITCH SKQSAB
SST0101AL038
R1803#
METAL OXIDE FILM RES. 1W J 18 Ω
RN01180ZU001
SW1209
TACT SWITCH SKQSAB
SST0101AL038
R1804
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
SW1210
TACT SWITCH SKQSAB
SST0101AL038
R1805
CHIP RES. 1/10W J 1.8k Ω
RRXAJR5Z0182
SW1211
LEAF SWITCH LSA-1142-2AU
SSC0101KB014
R1806
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
SW1212
SWITCH ROTARY SSS-53MD-1
SSR0106KB004
R1807
CHIP RES. 1/10W J 1.8k Ω
RRXAJR5Z0182
R1808#
METAL OXIDE FILM RES. 1W J 18 Ω
RN01180ZU001
BC1001
PCB JUMPER D0.6-P5.0
JW5.0T
R1809
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
BC1100
PCB JUMPER D0.6-P5.0
JW5.0T
R1810
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
BC1600
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
R1813
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
BC1606
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
R1814
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
CF1032
CERAMIC SIF FILTER EFCS4R5YS8P
FBB455LMS001
R1815
CHIP RES. 1/10W J 33k Ω
RRXAJR5Z0333
CL1201
JCFNG12JG020
R1816
CHIP RES. 1/10W J 33k Ω
RRXAJR5Z0333
FMN CONNECTOR TOP 12P 12FMN-BTRKA(LF)(SN)
R1850
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
F1601#
FUSE 4.00A/125V
PAGG20CNG402
RRXAJR5Z0104
FH1601
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
RCA JACK(YELLOW) (PB FREE) AV-3B-54H
JXRL010SNJ01
R1802#
R1851
CHIP RES. 1/10W J 100k Ω
MISCELLANEOUS
R1852
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
FH1602
R1853
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
JK1701
R1854
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
JK1702
RCA JACK(WHITE) MTJ-032-05B-22(B110)
JXRL010LY136
RCA JACK(RED) (PB FREE) AV-3A-57H
JYRL010SNJ01
MINIATURE JACK(PB FREE) CKX-035-318AZ4 JYSL010SNJ01
R1855
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
JK1703
R1856
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
JK1801
R1857
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
PS1601# THERMISTOR ZPB45BL3R0A
R1858
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
RS1201
R1859
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
SA1601# SURGE ABSORBER 470V+-10PER
NVQZ10D471KB
SF1001
FILTER CERAMIC BAND PASS
SAFHS45M7VAJZ00B05
FBB456LMR004
T1601#
TRANS POWER BCK-35-0396
LTT3PC0XB013
T1901#
TRANS POWER BCK-25-0127
LTT2PC0XB014
TB3
HEAD SHIELD T1200UA
1EM321250
TB8
BUSH LED(F) H3700UD
0VM409508
TB9
MODULE HEAT SINK PMC P7150UT
1EM423968
TB10
X8 MAIN HEAT SINK PLY ASSEMBLY P7750UM 1EM423970
TL2
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
TP1202
PCB JUMPER D0.6-P21.0
JW21.0T
TP1401
PCB JUMPER D0.6-P24.0
JW24.0T
TP1402
PCB JUMPER D0.6-P22.0
JW22.0T
TP1403
PCB JUMPER D0.6-P22.0
JW22.0T
TP1703
PCB JUMPER D0.6-P7.5
JW7.5T
TU1010
TUNER UNIT ENV56M07D8F
UTUNATSMS001
W1601#
AC CORD (PB FREE) A0A0280-014
R1860
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R1871
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1872
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1873
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
R1874
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R1875
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1876
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R1877
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R1901
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
R1902
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1903
CHIP RES. 1/10W J 3.9k Ω
RRXAJR5Z0392
R1904
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1905
CHIP RES. 1/10W J 3.3 Ω
RRXAJR5Z03R3
R1907
CARBON RES. 1/4W J 1.2k Ω
RCX4JATZ0122
R1908
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R1909
CHIP RES. 1/10W F 3.9k Ω
RRXAFR5H3901
R1910
CHIP RES. 1/10W F 560 Ω
RRXAFR5H5600
R1911
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
R1913
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R1914
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R1915#
METAL OXIDE FILM RES. 1W J 1.2 Ω
RN011R2ZU001
R1916
CARBON RES. 1/4W J 39k Ω
RCX4JATZ0393
R1917
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R1919
CARBON RES. 1/4W J 680 Ω
RCX4JATZ0681
R1920
CARBON RES. 1/4W J 1M Ω
RCX4JATZ0105
R1921
CARBON RES. 1/4W J 1M Ω
RCX4JATZ0105
R1923#
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R1924
CARBON RES. 1/4W J 22k Ω
VR1601# CARBON P.O.T. VZ067TL1 B103 PB(F)
WAC0172LTE14
VRCB103HH014
X1201
XTAL DT38 32.768kHz
FX0323LDS001
X1202
XTAL HC-49/U 10.6MHz
FXD106LLN001
X1401
XTAL 3.579545MHz(20PPM)
FXC355LLN004
SG1601# GAP. FNR-G3.10D
FAZ000LD6005
SENSOR CBA
Ref. No.
Description
SENSOR CBA
Consists of the following:
Part No.
1ESA12193
TRANSISTORS
RCX4JATZ0223
Q1201
PHOTO TRANSISTOR MID-32A22F
NPWZ1D32A22F
Q1202
PHOTO TRANSISTOR MID-32A22F
NPWZ1D32A22F
R1925
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R1926
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
R1927
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
R1928
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R1929
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
MPS CBA
Ref. No.
SWITCHES
SW1201
TACT SWITCH SKQSAB
SST0101AL038
SW1202
TACT SWITCH SKQSAB
SST0101AL038
SW1203
TACT SWITCH SKQSAB
SST0101AL038
SW1206
TACT SWITCH SKQSAB
SST0101AL038
SW1207
TACT SWITCH SKQSAB
SST0101AL038
20070131
QNBZ45BL3R0A
SENSOR REMOTE RECEIVER KSM-602LU2S USESJRSKK048
1-19-6
Description
Part No.
MPS CBA
Consists of the following:
1ESA14054
SUB CBA (MPS-A)
CRT CBA (MPS-B)
FUNCTION CBA (MPS-C)
JUNCTION-A CBA
JUNCTION-B CBA
----------------------------------------------
P7754EL
SUB CBA
Ref. No.
Ref. No.
Description
SUB CBA (MPS-A)
Consists of the following:
Description
Part No.
----------
CAPACITORS
Part No.
DIODES
D2300
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D2301
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D2302
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2305
ELECTROLYTIC CAP. 470µF/10V M
CE1AMASDL471
D2304
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2307
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D2305
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2308
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2307
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2309
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D2308
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2310
STACKED FILM CAP. 0.47µF/50V J
CMA1JJS00474
D2552#
DIODE FR104-B
NDLZ000FR104
C2311
ELECTROLYTIC CAP. 220µF/10V M
CE1AMASDL221
D2571
FAST RECOVERY DIODE FR202
NDWZ000FR202
C2315
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
D2572#
DIODE FR104-B
NDLZ000FR104
C2316
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2575#
ZENER DIODE MTZJT-7710B
QDTB00MTZJ10
C2317
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2584
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2318
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2585
ZENER DIODE MTZJT-775.1B
QDTB0MTZJ5R1
C2320
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
D2586
PCB JUMPER D0.6-P5.0
JW5.0T
C2321
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
D2591#
ZENER DIODE MTZJT-7736B
QDTB00MTZJ36
C2322
ELECTROLYTIC CAP. 0.47µF/50V M
CE1JMASDLR47
D2595#
ZENER DIODE MTZJT-7722C
QDTC00MTZJ22
C2323
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
D2596#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2324
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2597
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2326
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D2598#
DIODE FR104-B
NDLZ000FR104
C2327
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
D2599
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
C2328
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
D2603#
ZENER DIODE MTZJT-775.6C
QDTC0MTZJ5R6
C2330
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2618
ZENER DIODE MTZJT-773.9A
QDTA0MTZJ3R9
C2331
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2627
ZENER DIODE MTZJT-773.9B
QDTB0MTZJ3R9
C2332
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2651
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2333
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D2652
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2334
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
D2661
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2531
METALIZED FILM CAP. 0.27µF/200V J
CT2D274F7003
D2662
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C2533#
P.P. CAP 0.0082µF/1.6K J
CA3C822VC011
ICS
C2552
FILM CAP.(P) 0.22µF/100V J
CMA2AJS00224
IC2301#
VCD IC M61276FP TF0H
QSZAB0RMB134
C2553
ELECTROLYTIC CAP. 2.2µF/50V LL
CE1JMASLH2R2
IC2551#
VERTICAL OUTPUT IC LA78040A
QSBBA0SSY003
C2555
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASDL470
IC2602#
VOLTAGE REGULATOR TLV1117IDCYRG3
NSZBA0TTY219
C2556
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZPDL102
IC3603
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
C2559
ELECTROLYTIC CAP. 220µF/35V M
CE1GMASDL221
C2560
FILM CAP.(P) 0.033µF/50V J
CMA1JJS00333
L2505
CHOKE COIL 22µH-K
LLBD00PKV021
C2574
ELECTROLYTIC CAP. 4.7µF/250V M
CE2EMASDL4R7
L2613
INDUCTOR 10µH-K-5FT
LLARKBSTU100
COILS
C2577
FILM CAP.(P) 0.022µF/50V J
CMA1JJS00223
C2578
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASDL470
Q2304#
NPN TRANSISTOR 2SC1627-Y (TE2.F.T)
QQSY2SC1627F
C2583
ELECTROLYTIC CAP. 1µF/160V M
CE2CMASDL1R0
Q2305#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
C2584#
PCB JUMPER D0.6-P5.0
JW5.0T
Q2571#
TRANSISTOR 2SC5885000RF
QQZZ02SC5885
C2585
CERAMIC CAP. B K 100pF/500V
CCD2JKS0B101
Q2591#
NPN TRANSISTOR 2SC1627-Y (TE2.F.T)
QQSY2SC1627F
C2586
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
Q2592#
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
TRANSISTORS
C2590
CHIP CERAMIC CAP. F Z 0.01µF/50V
CHD1JZ30F103
Q2601
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
C2592
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASDL470
Q2608
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
C2594
ELECTROLYTIC CAP. 47µF/160V M W/F
CE2CMZNDL470
Q2609
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
C2595#
CERAMIC CAP. 1200pF/2KV
CA3D122PAN04
Q2610#
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
C2596
PCB JUMPER D0.6-P5.0
JW5.0T
Q2611#
TRANSISTOR KTC3199-Y-AT/P
NQSYKTC3199P
C2601
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
Q2612
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
C2603
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
Q2615#
TRANSISTOR 2SD400(F)
QQUF002SD400
C2605
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
Q2616
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
C2606
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
Q2617#
TRANSISTOR KTC3199-Y-AT/P
NQSYKTC3199P
Q2618#
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
C2609
ELECTROLYTIC CAP. 47µF/50V M
CE1JMASDL470
C2616
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASDL101
C2629
ELECTROLYTIC CAP. 220µF/6.3V M
CE0KMASDL221
R2301
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
C2630
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASDL471
R2303
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
C2670
ELECTROLYTIC CAP. 470µF/6.3V M
CE0KMASDL471
R2305
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
R2306
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
CONNECTORS
RESISTORS
CN2103
TWG CONNECTOR 19P TWG-P19P-A1
J3TWA19TG001
R2307
CHIP RES. 1/10W J 470 Ω
RRXAJR5Z0471
CN2301
TWG CONNECTOR 19P TWG-P19P-A1
J3TWA19TG001
R2309
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
CN2302
TWG CONNECTOR 19P TWG-P19P-A1
J3TWA19TG001
R2310
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
CN2571# CONNECTOR PRINT OSU 5P RTB-1.5-5P (LF) J3RTC05JG002
R2311
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R2319
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
20070131
1-19-7
P7754EL
Ref. No.
Description
Ref. No.
Part No.
Description
Part No.
CARBON RES. 1/4W J 470 Ω
RCX4JATZ0471
R2649#
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
R2322
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
R2650
CARBON RES. 1/4W J 1.2 Ω
RCX4JATZ01R2
R2323
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R2651
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R2324
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R2653
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
R2325
CHIP RES. 1/10W J 3.3M Ω
RRXAJR5Z0335
R2655
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R2326
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R2656
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R2327
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R2657
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R2328
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R2658
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R2331
CHIP RES. 1/10W J 180k Ω
RRXAJR5Z0184
R2659
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R2332
CHIP RES. 1/10W J 120k Ω
RRXAJR5Z0124
R2660
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R2333
CARBON RES. 1/4W J 18 Ω
RCX4JATZ0180
R2675
CHIP RES. 1/10W J 150 Ω
RRXAJR5Z0151
R2501
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R2676
CHIP RES. 1/10W J 82k Ω
RRXAJR5Z0823
R2504
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R2677
METAL OXIDE FILM RES. 1/2W J 0.47 Ω
RNX2JZPZ0R47
R2505
METAL OXIDE FILM RES. 2W J 1k Ω
RN02102ZU001
R2678
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R2506
METAL OXIDE FILM RES. 2W J 1k Ω
RN02102ZU001
R2680
RES CHIP.(1608) 1/10W J 0.30 Ω
RRXAR30HH007
R2541
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R2681
RES CHIP.(1608) 1/10W J 0.30 Ω
RRXAR30HH007
R2550
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2686
CARBON RES. 1/4W J 330 Ω
RCX4JATZ0331
R2551
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
R2687
CHIP RES. 1/10W F 5.6k Ω
RRXAFR5H5601
R2552
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2688
CHIP RES. 1/10W F 15k Ω
RRXAFR5H1502
R2555
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R2691
CARBON RES. 1/4W J 1 Ω
RCX4JATZ01R0
R2556
CARBON RES. 1/4W J 1 Ω
RCX4JATZ01R0
R2692
CHIP RES. 1/10W J 130 Ω
RRXAJR5Z0131
R2557
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R2693
CHIP RES. 1/10W J 130 Ω
RRXAJR5Z0131
R2558
CHIP RES. 1/10W J 12k Ω
RRXAJR5Z0123
R3521#
METAL OXIDE FILM RES. 1W J 10 Ω
RN01100ZU001
R2559
CHIP RES.(1608) 1/10W 0 Ω
RRXAJR5Z0000
R3568#
CARBON RES. 1/4W J 3.3 Ω
RCX4JATZ03R3
R2560
CHIP RES. 1/10W J 2.7k Ω
RRXAJR5Z0272
R3576
PCB JUMPER D0.6-P5.0
JW5.0T
R2561
CHIP RES. 1/10W J 3.9k Ω
RRXAJR5Z0392
R3580#
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
R2562
CARBON RES. 1/4W J 6.8 Ω
RCX4JATZ06R8
R2563
CARBON RES. 1/4W J 6.8 Ω
RCX4JATZ06R8
BC2501
BEAD INDUCTOR FBA04HA600VB-00
LLBF00STU026
R2564
CARBON RES. 1/4W J 6.8 Ω
RCX4JATZ06R8
CL2501
LEAD WIRE 3P 420MM
WX1T1000-001
WX1T2120-001
R2321
MISCELLANEOUS
R2565
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
CL2504
LEAD WIRE 5P 330MM
R2566
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
JK2601
JACK RCA PCB L MSP-241V-05 NI LFW/O
JXRL010LY148
R2571
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
T2571#
TRANS FBT JF0501-3201A-G
LTF00CPXB048
R2572
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
T2572#
HORIZONTAL DRIVE TRANS LP2-005
LTH00CPA5005
R2573
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
TB11
X8 H/V HEAT SINK PLZ P7750UM
1EM423971
R2576
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
TL2
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
R2577
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
TP1301
PCB JUMPER D0.6-P7.5
JW7.5T
R2580#
CARBON RES. 1/4W J 33 Ω
RCX4JATZ0330
TP1302
PCB JUMPER D0.6-P7.5
JW7.5T
R2581
CHIP RES. 1/10W J 470 Ω
RRXAJR5Z0471
TP1303
PCB JUMPER D0.6-P7.5
JW7.5T
R2583#
METAL RESISTER. 2W J 2.7 Ω
RN022R7ZU001
TP2501
PCB JUMPER D0.6-P10.0
JW10.0T
R2584
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
TP2502
PCB JUMPER D0.6-P27.5
JW27.5T
R2585
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
TP2503
PCB JUMPER D0.6-P14.0
JW14.0T
R2586
PCB JUMPER D0.6-P5.0
JW5.0T
TP2504
PCB JUMPER D0.6-P18.0
JW18.0T
R2587
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
TP2505
PCB JUMPER D0.6-P14.0
JW14.0T
R2588
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
TP2506
PCB JUMPER D0.6-P11.0
JW11.0T
R2589#
CARBON RES. 1/4W J 27 Ω
RCX4JATZ0270
X2301
XTAL 3.579545 MHz
FXD355LLN003
R2590#
CARBON RES. 1/4W J 27 Ω
RCX4JATZ0270
R2591
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R2592#
CARBON RES. 1/4W G 180k Ω
RCX4GATZ0184
CRT CBA
Ref. No.
Description
Part No.
R2593#
CARBON RES. 1/4W G 82k Ω
RCX4GATZ0823
R2594
CARBON RES. 1/4W G 56k Ω
RCX4GATZ0563
R2599
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
R2601
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R2602
CHIP RES. 1/10W J 560 Ω
RRXAJR5Z0561
R2603
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
R2604
CHIP RES. 1/10W J 2k Ω
RRXAJR5Z0202
R2607
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R2608
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R2609
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R2610
CARBON RES. 1/4W J 75 Ω
RCX4JATZ0750
R2611
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R2613
CARBON RES. 1/4W J 1 Ω
RCX4JATZ01R0
D2501
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R2617
CARBON RES. 1/4W J 390 Ω
RCX4JATZ0391
D2502
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
RCX4JATZ0391
D2503
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R2618
CARBON RES. 1/4W J 390 Ω
20070131
CRT CBA (MPS-B)
Consists of the following:
----------
CAPACITORS
C2504
CERAMIC CAP.(AX) B J 390pF/50V
CCA1JJT0B391
C2505
CERAMIC CAP.(AX) B J 330pF/50V
CCA1JJT0B331
C2506
CERAMIC CAP.(AX) B J 330pF/50V
CCA1JJT0B331
C2508
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASDL470
C2509#
CERAMIC CAP. B K 1000pF/2KV
CCD3DKP0B102
CONNECTOR
CN2501
CONNECTOR PIN 1P RT-01N-2.3A
1730688
DIODES
1-19-8
P7754EL
Ref. No.
D2505
Description
PCB JUMPER D0.6-P5.0
Part No.
JUNCTION-A CBA
JW5.0T
Ref. No.
COIL
L2501
INDUCTOR 180µH-J-5FT
Description
JUNCTION-A CBA
Consists of the following:
LLARJCSTU181
TRANSISTORS
Part No.
----------
CONNECTOR
Q2501#
NPN TRANSISTOR 2SC2482(T6FUNAIF M
QRSZ2SC2482F
Q2502#
NPN TRANSISTOR 2SC2482(T6FUNAIF M
QRSZ2SC2482F
Q2503#
NPN TRANSISTOR 2SC2482(T6FUNAIF M
QRSZ2SC2482F
RESISTORS
R2502
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2503
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2507
CHIP RES. 1/10W J 33 Ω
RRXAJR5Z0330
R2508
CHIP RES. 1/10W J 33 Ω
RRXAJR5Z0330
R2509
CHIP RES. 1/10W J 33 Ω
RRXAJR5Z0330
R2510
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R2511
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R2512
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R2513
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R2514
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R2515
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R2516#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153DP003
R2517#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153DP003
R2518#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153DP003
R2519
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2520
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2521
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R2523
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
CN3802
242 SERIES CONNECTOR TUC-P04X-B1 WHT JCTUB04TG002
ST
CL3802
WIRE ASSEMBLY 2P 180MM
MISCELLANEOUS
WX1T9200-005
JUNCTION-B CBA
Ref. No.
Description
JUNCTION-B CBA
Consists of the following:
Part No.
----------
CONNECTOR
CN3801
242 SERIES CONNECTOR TUC-P04X-B1 WHT JCTUB04TG002
ST
CL3801
WIRE ASSEMBLY 2P 180MM
MISCELLANEOUS
WX1T9200-005
MISCELLANEOUS
JK2501# CRT SOCKET ISMP02S
JSCC220PK009
FUNCTION CBA
Ref. No.
Description
FUNCTION CBA (MPS-C)
Consists of the following:
Part No.
----------
CONNECTORS
CN2401
BOARD CONNECTOR 07P(PB FREE)
127301107K2
JCTWA07TG004
CN2801
242 SERIES CONNECTOR 224202104W1
J322C04TG001
RESISTORS
R2401
CHIP RES. 1/10W F 1.5k Ω
RRXAFR5H1501
R2402
CHIP RES. 1/10W F 1.5k Ω
RRXAFR5H1501
R2403
CHIP RES. 1/10W F 2.2k Ω
RRXAFR5H2201
R2404
CHIP RES. 1/10W F 2.7k Ω
RRXAFR5H2701
R2405
CHIP RES. 1/10W F 4.7k Ω
RRXAFR5H4701
R2406
CHIP RES. 1/10W F 6.8k Ω
RRXAFR5H6801
R2407
CHIP RES. 1/10W F 15k Ω
RRXAFR5H1502
SW2401
TACT SWITCH SKQSAB
SST0101AL038
SW2402
TACT SWITCH SKQSAB
SST0101AL038
SW2403
TACT SWITCH SKQSAB
SST0101AL038
SW2404
TACT SWITCH SKQSAB
SST0101AL038
SW2405
TACT SWITCH SKQSAB
SST0101AL038
SW2406
TACT SWITCH SKQSAB
SST0101AL038
SW2407
TACT SWITCH SKQSAB
SST0101AL038
SW2408
TACT SWITCH SKQSAB
SST0101AL038
SWITCHES
20070131
1-19-9
P7754EL
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
CT202MW8
P7754UT
2007-02-06
Download PDF
Similar pages