OneTouch AT G2 And 10G Network Assistant

5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
DATASHEET
OneTouch AT G2 And 10G Network Assistant
Reduce network troubleshooting time
More than 70% of IT organizations lack
standardized processes to validate
deployment and solve problems. This
results in more than 1 hour (average) to
resolve problems. In addition, 40% of IT
tickets are not solved the ౔rst time and
require escalation. Intermittent problems
can take twice as long to resolve.
By automating and standardizing the
validation and troubleshooting process,
the OneTouch™ AT Network Assistant
empowers novice network technicians to
validate performance easily, solve more
problems faster, and escalate issues
more e౔ciently—allowing more IT
projects to be completed on time.
Empower IT professional teams to e ectively validate,
and troubleshoot Ethernet and Wi-Fi access networks









All-in-one: a handheld tester combining infrastructure, network service
and end-to-end path performance measurement in one tool.
Versatile: The OneTouch AT has a modular design: select the G2
module that has dual 10/100/1G copper/fiber Ethernet test ports and
802.11a/b/g/n/ac Wi-Fi radio, or the 10G module that has 100M/1/10G
copper and fiber Ethernet test ports.
Standardize: Network engineers can pre-program AutoTest profiles for field technicians to choose that
automatically run a suite of tests with the press of a button, enabling identification of the most common
problems in about a minute.
Authoritative: Measure end-to-end path performance prior and after the deployment of new services or
network infrastructure to assess network readiness and post deployment to prove SLA compliance.
Visibility: Switched Ethernet as well as Wi-Fi discovery and analysis provides visibility and documentation into
connected devices, key device properties and problems.
Collaborative: Engineers can take full remote-control of the OneTouch AT to collaborate with on-site
technicians and speed isolation of issues.
VoIP ready: The G2 module troubleshoots desktop SIP/SCCP-based VoIP problems in real-time with inline call
monitoring, logging and scoring.
Capture friendly: Wired or Wi-Fi packet capture streamlines collaboration and escalation of the most
complex issues. Capturing wireline traffic using the G2 module’s inline capture features avoids the need for
SPAN port or TAP.
Centralized Management: The Link-Live Cloud Service is a portal that offers visibility to all of the test results
and project progress from any NETSCOUT handheld network test tool (LinkSprinter, LinkRunner AT, AirCheck
G2 and OneTouch AT), when the tester is dispatched for troubleshooting or validating network installation.
OneTouch AT features
http://enterprise.netscout.com/node/126971/draft
1/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
OneTouch AT features
Versatile copper, ២�ber and Wi-Fi troubleshooting
Be ready for a broad range of troubleshooting scenarios with the handheld OneTouch AT G2 Network Assistant.
The tester incorporates dual copper and fiber-optic test ports to facilitate troubleshooting of 10/100/1000 Mbps
twisted pair and 100/1000 Mbps fiber ethernet networks. The dual ports simplifies inline packet capture and
VoIP monitoring by eliminating the need for mirror ports or taps. For troubleshooting Wi-Fi networks, the
OneTouch AT G2 tester incorporates an 802.11ac dual-band Wi-Fi radio with a 3x3 antenna. When connected to
both wired and Wi-Fi networks the tester displays test results side-by-side on a single page to aid in problem
domain isolation.
The OneTouch AT Network Assistant has a modular design. The 10G module is available for testing wired 100
Mbps to 10 Gbps ethernet switch port and link performance at up to 10 Gbps rate.
All-in-one testing from the patch cable & Wi-Fi to the cloud
When validating and troubleshooting the access network, one needs to test from where the client device is
connected to the network—where the device could be a PC, tablet, smart phone, IP phone, printer, POS
terminal, industrial equipment controller, medical imager etc. The OneTouch AT can prove that the network is
good—by emulating the client device and measuring network performance. It measures, analyzes and
documents the performance of each the critical network elements: the network cabling, the delivery of Power
over Ethernet (PoE), the connection to the nearest switch, the connection to the nearest access point (AP), and
the performance of key network services and server-based applications in the intranet, cloud or internet.
Standardized network validation and troubleshooting
Use the intuitive touch interface and the Setup Wizard to create test profiles, where a profile is a set of tests
tailored to specific networks, services, and applications. Build profiles to accommodate different types of users,
devices, locations or technologies. Profiles can be very simple with just a few tests or advanced with dozens of
tests. Once created, profiles can be saved for quick and easy reuse. Create a library of standardized profiles to
elevate the troubleshooting know-how of the entire network support staff. Share profiles with other OneTouch
AT users. Use the profiles to establish best practices for consistent, faster, more productive troubleshooting and
network acceptance testing.
Automated suite of tests with pass/fail analysis
Test everything defined in a profile automatically with the one-button AutoTest. The AutoTest progresses from
the physical layer of the network through the wired and wireless infrastructure, to network services and userdefined applications. Clear pass/fail and warning indicators highlight potential problems. A top-level pass/fail
indicator provides the overall AutoTest status at a glance.
http://enterprise.netscout.com/node/126971/draft
2/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
User-De៍�ned Performance Tests
Connectivity and response time test to application/servers, and performance test to
end-point(s) in all three network layers: the local broadcast domain, the private
intranet and the public cloud (internet).
Client Network Analysis
Cable and nearest switch test, Wi-Fi network accessibility test, Wired and Wi-Fi access
network/device discovery & network service tests: DHCP & DNS & 802.1x
Figure 1. The AutoTest provides a
comprehensive measurement of network
performance from the end user point-ofview, from cable, to services and applications
(Test result from OneTouch AT with G2
Modules for both Wired and Wi-Fi network
shown)
Centralized cloud-based management
Organizations can claim their OneTouch AT units to the Link-Live Cloud Service. Claimed units will be visible
from Link-Live as long as they are connected to the internet. They can be remotely managed when and where it
is convenient using a smart device through its web browser. Users can upload, view and analyze test results,
download latest software and test profiles, and control their OneTouch AT remotely.
Centralized report management
The Link-Live Cloud Service supports storing and viewing of test results from many NETSCOUT handheld
network test products, such as LinkSprinter, LinkRunner AT, and AirCheck G2. A user can automatically receive
an email after each test. The operator of the OneTouch can enter comments, such as test location, and/or
upload picture(s) of the test environment by replying to the email results they receive. Multiple parties can
access Link-Live over the web at anytime from anywhere using a smart device or PC via a web browser.
Figure 2. Link-Live consolidates test results from OneTouch AT
http://enterprise.netscout.com/node/126971/draft
3/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Remote visibility, control and ២�le access
Use the built-in RJ-45 management port or optional USB Wi-Fi adapter to remotely control the OneTouch AT and
access saved files. Any action that can be performed directly on the OneTouch AT using the touch screen can be
performed remotely using a PC, laptop, smart phone or tablet. This will minimize the time, expense and
inconvenience of traveling to the client location where the problem was reported. Webcam support enables live,
remote viewing of the physical environment near the tester. Remote-control of units via the Link-Live Cloud
Service also allows traversal of NAT devices, which is very advantageous when troubleshooting from outside the
office.
Figure 3A. Remotely control the OneTouch AT and access saved results using a Laptop, or tablet
Figure 3B. Remotely control the OneTouch AT
through VNC client (TightVNC Viewer shown)
Test Features
http://enterprise.netscout.com/node/126971/draft
4/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Test Features
Copper and ២�ber-optic cable testing (Supported with OneTouch AT G2 module)
Troubleshoot cable performance quickly by measuring twisted pair cable wiremap and length. Use cable
identifiers and tone probe to locate and identify cables. Measure the optical power received through fiber-optic
links. Verify the cleanliness of fiber-optic connections by viewing connector end faces with the optional USB
video probe.
PoE testing (Supported with OneTouch AT G2 Module)
Verify the successful delivery of PoE with the TruePower™ load test. Emulate an 802.3at (PoE+) class 1-4
powered device and measure power up to 25.5 watts. See the requested and received PoE class, the pairs used,
the PSE type, measured PoE voltage unloaded and under load, and PoE power under load.
Wi-Fi and wired client devices connectivity testing
Understand how a client device connects to the wired infrastructure by testing link negotiation, identifying the
nearest switch, and monitoring key switch port statistics. The OneTouch AT with G2 module tests IEEE 802.11a,
.11b, .11g, .11n and .11ac Wi-Fi networks. It shows how a client device connects to the Wi-Fi infrastructure by
testing the link between the client and the nearest access point, identifying the AP name, channel and security
type, observing the authentication and association process, and monitoring key AP and network statistics,
including roaming details by the AP. For wired clients, the OneTouch AT with G2 module tests 10/100/1000BASET twisted pair and 100BASE-FX/1000BASE-X fiber-optic ethernet networks, while the OneTouch AT with 10G
Module test RJ-45 test port for 100/1000/10GBASE-T and 1000 BASE-X SFP/10 G BASE-SR/LR SFP+ ethernet over
optical fiber network.
Figure 4. Test link speed over twisted pair
and ᐔber-optic links at rates up to 1 Gbps
and measure PoE voltage with the G2 Module
Figure 5. Test a Wi-Fi connection at up to
802.11ac rates and verify channel width,
signal and noise level
Network services testing
Test DHCP server responsiveness. Identify the wired and Wi-Fi DHCP servers and view the offer and acceptance
timing and the lease information. Test DNS server responsiveness. Identify the wired and Wi-Fi DNS servers and
view the DNS lookup time. Also, determine if a second DHCP address is being offered. If unexpected or is a
potential rogue server, use the path analysis tool—a layer 2 and layer 3 trace route—to track down the device to
mitigate a problem situation.
http://enterprise.netscout.com/node/126971/draft
5/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Figure 6. Detailed breakdown of DHCP
provisioning and response performance
Figure 7. Path Analysis showing the path
through switches from OneTouch AT to a
client
Network application testing
Determine if a server-based application is the root cause of a reported problem by measuring availability and
response metrics. Add to the AutoTest profile the performance test appropriate for the application: ping (ICMP),
connect (TCP), web (HTTP), file (FTP), multicast (IGMP), video (RTSP) or email (SMTP). Each test is graphically
represented on the OneTouch AT home page as an icon. After running the AutoTest, touch a test icon on the
home page to get a detailed breakdown of application performance including DNS lookup time, server-response
time and data rate. The test results are presented side-by-side for easy wired/Wi-Fi and IPv4/IPv6 performance
comparisons. A few examples: ping your WLAN controller, connect to port 2000 on your VoIP call manager,
download a page of an application with a web interface, upload or download a file from a server, subscribe to a
multicast group, access video content from an on-demand streaming video server or email a text message to
your mobile phone.
Figure 8. Detailed breakdown of networkhosted application performance
Figure 9. Group tests by hosting location –
local, intranet, internet
Local, intranet and internet performance
http://enterprise.netscout.com/node/126971/draft
6/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Local, intranet and internet performance
Understand the performance of network services and server-based applications wherever they are hosted:
locally in the datacenter, on a corporate intranet server or on a server reached via the public internet. Create
location-centric AutoTest profiles by grouping together co-located services and applications. Measure service
levels to the different groups to quickly spot problems.
Enterprise network managers use the Wired Performance tests for:




Assessing network performance prior to deployment of new services or network infrastructure
Validating the performance of newly installed network infrastructure and critical network links within the LAN
or data center
Troubleshooting network and service performance problems
Verifying independently that service providers are meeting agreed upon service levels (SLAs) and maintaining
QoS end-to-end
Service providers and system integrators use the Wired Performance tests for:


Documenting network performance from layer 1 to 7 where the documentation serves as proof that the
services they provided were delivered successfully
Providing value-added service to their enterprise customers in the form of network assessments and
troubleshooting
1G and Wi-Fi End-to-end path performance measurement
Ensure that newly installed or upgraded wired and Wi-Fi networks meet SLA objectives and are ready for new
high-bandwidth applications by measuring end-to-end path performance. Measure throughput, frame loss,
latency and jitter between a local OneTouch AT G2 connected to Wi-Fi or wired client network, and a remote
OneTouch AT peer or a remote LinkRunner reflector connected to the end of the path to test. A remote peer
provides upstream and downstream results while a remote reflector yields round trip results. Measure
performance at rates up to 1 Gbps on copper and fiber networks and 600 Mbps on Wi-Fi networks. A special use
model exists that enables testing from the OneTouch AT wired interface to the Wi-Fi interface on the same
instrument for testing without a remote.
Figure 10. End-to-end path performance
measurement validates link readiness and
SLA compliance
http://enterprise.netscout.com/node/126971/draft
7/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
The OneTouch AT with G2 module will be located at one end. There are options for the test instrument to be
located at the other end of the link. The OneTouch AT with G2 module also support loop back testing to itself
from its wire to its Wi-Fi interface.
Remote Tester (End-Point)
OneTouch AT G2 as local
LinkRunner AT 2000
OneTouch AT G2 (wired)
< 600 Mbps Wi-Fi
✓
✓
≤ 1 Gbps rate
✓
✓
1 traffic stream
✓
✓
Round trip results
✓
Bi-directional results
Frame loss, latency, jitter
OneTouch AT G2 (wired)
✓
✓
10G End-to-end path performance measurement
The OneTouch AT with 10G module features 10G and 1G Wired Performance tests for validating and
troubleshooting end-to-end network path performance. These Wired Performance tests facilitate measurement
of throughput, frame loss, latency and jitter across wide area networks, local area networks as well as within
sites and datacenters.
http://enterprise.netscout.com/node/126971/draft
8/17
5/9/2017
Figure 11. Detailed breakdown of XG custom
performance
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Figure 12. Detailed breakdown of wired to
peer
The OneTouch AT with 10G module will be located at one end. There are options for the test instrument to be
located at the other end of the link.
http://enterprise.netscout.com/node/126971/draft
9/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Remote Tester (End-Point)
OneTouch AT 10G as local
LinkRunner AT
2000
OneTouch
AT G2
OneTouch AT
10G
≤ 1 Gbps rate
✓
✓
✓
1 traffic stream
✓
✓
✓
IETF RFC 2544 test method
✓
✓
✓
Round trip results
✓
✓
✓
✓
✓
Bi-directional results
Frame loss, latency, jitter
✓
OptiView
XG
≤ 10 Gbps rate
✓
≤ 4 traffic streams
✓
ITU Y.1564 test method
✓
Throughput, availability, information rate,
burst rate
✓
Class of service testing, traffic policing
✓
Wired network discovery and analysis
Automatically discover copper and fiber-connected devices. Select from up to 14 different sorts to obtain
different views into the wired network. For example, sort by the IPv4 or IPv6 address to identify used and
available addresses. Or sort by switch name/slot/port to understand where on the network devices are
connected. Sort by discovered problems to quickly identify potential issues. Additional discovery-assisted
analysis tools aid with troubleshooting and profile creation. For example, the Multiport Statistics tool provides
visibility into switch, router and AP port statistics including speed, duplex, slot, port, VLANs, host count,
utilization, discards and errors. The Devices on Port tool provides visibility into the devices connected to an
individual switch port. The Path Analysis tool provides a layer 2 and 3 trace route from the OneTouch AT to a
target device including time to each hop and SNMP switch and router port statistics.
Wi-Fi discovery and analysis (supported by OneTouch AT G2 Module)
Automatically discover Wi-Fi devices and key device properties. Select from up to 12 context-relative sorts to
obtain different views into the wireless network. For example, sort by signal strength to troubleshoot Wi-Fi
coverage issues. Sort by MAC manufacturer to discover Wi-Fi devices by type and to understand how they are
connected relative to SSID, AP and channel. Sort by channel to identify channel spacing and usage problems.
Sort by authorization status to find potential security violations. Additional discovery-assisted analysis tools aid
with troubleshooting and security enforcement. If a Wi-Fi device is also discovered via Wired Analysis, the Cross
Link feature enables one-button toggling between wired and Wi-Fi analysis views.
http://enterprise.netscout.com/node/126971/draft
10/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Figure 13. Analyze Wi-Fi health by each
available channels
Figure 14. Visibility into each Wi-Fi channel,
showing bandwidth occupied by 802.11 and
non-802.11 traᐔc
Figure 15. Unique Interferer analysis
classiᐔes sources of non-802.11
Figure 16. Detailed information about a
speciᐔc interference source
Inline VoIP analysis (Supported by OneTouch AT G2 Module only)
Connect the OneTouch AT inline between an IP phone and the network for real-time troubleshooting and
analysis. The VoIP analysis test reveals issues related to PoE, DHCP, TFTP, SIP, and SCCP. The test provides
visibility into unencrypted SIP and SCCP traffic to debug VoIP phone problems and quantify the quality of a VoIP
call. Simultaneous capture of the VoIP conversation is optional.
http://enterprise.netscout.com/node/126971/draft
11/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Figure 17. Inline VoIP analysis simpliᐔes
troubleshooting of desktop VoIP problems in
real-time without TAPs or switch mirror ports
Figure 18. VoIP Analysis shows the entire call
setup process as well as quality of the VoIP
call in each direction
Packet capture
Capture wired and AutoTest traffic when a packet-level view is required to solve a complex network or
application issue. Filter the traffic to capture what is most important. Export the capture file to a PC for
decoding and analysis using protocol analysis software. Capture wired traffic on a single port, on two ports
aggregated, or inline between a client device and the network. Inline capture avoids the complexity, time and
cost associated with standalone taps or configuring switch mirror ports. The OneTouch AT with G2 module can
capture VoIP traffic, and Wi-Fi traffic by channel and mode (20 MHz or 40+ MHz).
Figure 19. Inline packet capture simpliᐔes
documentation of client application
problems without TAPs or SPAN ports
Streamline collaboration
http://enterprise.netscout.com/node/126971/draft
Figure 20. Capture packets to solve complex
issues
12/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Streamline collaboration
Collaborate with peers, consultants, integrators and vendors more effectively by sharing packet captures,
screen shots and AutoTest reports. Remotely control and view the user interface and remotely access files using
a PC, laptop, tablet or smart phone. Attach a web cam to the OneTouch AT to share a view of the test
environment.
Save test results
Save the test results to share with colleagues or outside parties. A report serves as trouble ticket
documentation, as a record of historical performance for benchmarking or as a certification report after new
infrastructure deployment and activation. Define which test results to include in the report (AutoTest, Wired
Analysis, Wi-Fi Analysis, Tools Settings, and VoIP Analysis) and the report format (PDF, XML). Open the results in
a spreadsheet for flexibility in results analysis.
Setup wizard
Simplify AutoTest profile creation while learning about the tester's capabilities by running the Setup Wizard. The
wizard simplifies profile creation with step-by-step guided instructions, yes/no prompts, on-screen help and
graphical progress indicators. Experienced users can bypass the wizard if desired.
Figure 21. Setup Wizard simpliᐔes creation of
AutoTest proᐔles
Figure 22. Detailed breakdown of network
service performance
Purpose-built for use by eld team
The OneTouch AT is engineered specifically for network support professionals on the go. Useful test and
management tools include a web browser, Telnet/SSH client, 3rd party cable toner, webcam support or fiberoptic connector inspection camera. Remote-control over web-browsers enable collaboration between field team
and skilled engineering resources in back-office. The durable platform provides years of reliable operation in
tough environments.
Gold Support
Protect your investment with Gold Support. Gold Support benefits include free software upgrades and MIB
updates, unlimited priority repair service with loaner units available, annual factory performance verification,
free accessory replacement, and 24x7 technical support with priority members-only access numbers.
Technical Speci cations
http://enterprise.netscout.com/node/126971/draft
13/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Technical Speci cations
GENERAL
Dimensions (with module
and battery installed)
10.3 in x 5.3 in x 2.9 in (26.2 cm x 13.5 cm x 7.3 cm)
Weight (with module and
battery installed)
3.5 lb (1.6 kg)
Display
5.7 in (14.5 cm) LCD with projected capacitance touch screen, 480 x 640 pixels
AC adapter
Input: 100-240 VAC, 50-60 Hz, 1.0 A
Output: +15 VDC, 2.0 A
Battery type
Lithium ion battery pack, 7.2 V
Battery life
Approximately 3-4 hours depending on type of usage, 4 hours to charge from
10% capacity to 90% capacity with the unit powered off
Memory
Internal: 2 GB shared between system and user files
SD card: 8 GB, brand and model selected for optimal performance
USB 2.0 type A port: for use with USB mass storage devices
Management port
One RJ-45 10/100BASE-T Ethernet
One USB 802.11 (requires optional adapter)
G2 MODULE NETWORK INTERFACES
Network analysis ports
Two RJ-45 10/100/1000BASE-T Ethernet
Two SFP 100BASE-FX/1000BASE-X Ethernet
Wi-Fi adapter data rate
802.11a: 6/9/12/24/36/48/54 Mbps
802.11b: 1/2/5.5/11 Mbps
802.11g: 6/9/12/24/36/48/54 Mbps
802.11n (20 MHz): MCS0-23, up to 216 Mbps
802.11n (40 MHz): MCS0-23, up to 450 Mbps
802.11ac (80 MHz): MCS0NSS1-MCS9NSS3, up to 1.3 Gbps
Wi-Fi adapter operating
frequency
2.412 ~ 2.484 GHz (Industrial Scientific Medical Band)
5.170 ~ 5.825 GHz
Wi-Fi security
64/128-Bit WEP Key, WPA/WPA2 personal, WPA/WPA2 enterprise,
802.1X
10G MODULE NETWORK INTERFACES
Network analysis ports
100/1000/10 G BASE-T RJ-45 Ethernet over twisted pair
1000 BASE-X SFP/10 G BASE-SR/LR SFP+ Ethernet over optical fiber
Management port
One RJ-45 10/100 BASE-T Ethernet
One USB 802.11 (requires optional adapter)
Supported network standards
IEEE
IEEE
IEEE
IEEE
IEEE
IEEE
RFCs and standard MIBs used
1213, 1231, 1239, 1285, 1493, 1512, 1513, 1643, 1757
1759, 2021, 2108, 2115, 2127, 2233, 2495, 2515, 2558
2618, 2737, 2790, 2819, 3592, 3895, 3896, 4188, 4502
100BASE-T
1000BASE-T
10GBASE-T
1000BASE-X
10GBASE-SR
10GBASE-LR
Note: The OneTouch AT analyzer is NOT designed for connection to a telephone network, ISDN line. Do not connect to a telephone
network or ISDN line except through a regulatory agency compliant computer network modem device.
COPPER CABLES TEST
http://enterprise.netscout.com/node/126971/draft
14/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
COPPER CABLES TEST
Cable types
100 Ω Unshielded Twisted Pair (UTP) LAN cables
100 Ω Shielded or Screened Twisted Pair (STP) LAN cables
TIA Category 3, 4, 5, 5e, and 6. ISO Class C, D, E and F
Cable length
measurement
Measurable cable lengths are from 3 feet (1 meter) to 656 feet (200 meters)
Accuracy: ± 30 feet (±10 meters)
Length measurement is based on Nominal Velocity of Propagation (NVP) for CAT
5e cable
ENVIRONMENTAL AND REGULATORY
Operating temperature
32°F to 122°F (0°C to 50°C)
Battery charging temperature
32°F to 104°F (0°C to 40°C)
Storage temperature
-40°F to 160°F (-40°C to 71°C)
-4°F to 122°F (-20°C to 50°C) for periods longer than 1 week
Operating relative humidity
(% RH without condensation)
5% to 45% at 32°F to 122°F (0°C to 50°C)
5% to 75% at 32°F to 104°F (0°C to 40°C)
5% to 95% at 32°F to 86°F (0°C to 30°C)
Shock and vibration
Meets the requirements of MIL-PRF-28800F for Class 3 Equipment
Safety
CAN/CSA-C22.2 No. 61010-1-04, IEC 61010-1:2001
Operating altitude
13,123 ft (4,000 m), 10,500 ft (3,200 m) with AC adapter
Storage altitude
39,370 ft (12,000 m)
Pollution degree
2
EMC
EN 61326-1:2006
CERTIFICATIONS AND COMPLIANCE
Conformite Europeene. Conforms to the requirements of the European Union and the European
Free Trade Association (EFTA)
Listed by the Canadian Standards Association
Conforms to relevant Australian standards
Conforms to relevant South Korean EMC Standards
Mainframes
Model
Description
1TG2-1500
ONETOUCH AT G2 ETHERNET TESTER
1TG2-3000
ONETOUCH AT G2 ETHERNET WI-FI TESTER
1T10G-1000
ONETOUCH AT 10G ETHERNET TESTER
http://enterprise.netscout.com/node/126971/draft
15/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Gold Support
Item
Description
1TG2-1500-1YS
1 Year Gold Tools Support for 1TG2-1500
1TG2-1500-3YS
3 Year Gold Tools Support for 1TG2-1500
1TG2-3000-1YS
1 Year Gold Tools Support for 1TG2-3000
1TG2-3000-3YS
3 Year Gold Tools Support for 1TG2-3000
1T10G-1000-1YS
1 Year Gold Tools Support for 1T10G-1000
1T10G-1000-3YS
3 Year Gold Tools Support for 1T10G-1000
One-year and three-year Gold Support is available for mainframes, bundles and upgrades. We encourage customers to purchase
Gold Support at the time of purchase. Purchase of Gold Support after product was shipped will be subjected to back-date charge.
Please contact your nearest NETSCOUT sales representative for models and pricing.
Options & Accessories
Model
Description
1TG2-3000-MOD
ONETOUCH AT G2 ETHERNET WI-FI TEST MODULE
1T10G-1000-MOD
ONETOUCH AT 10G ETHERNET TEST MODULE
1T-BATTERY
REPLACEMENT BATTERY FOR ONETOUCH AT
PWR-CHARGER
AC CHARGER REPLACEMENT
1T-ANT
ONETOUCH AT EXTERNAL DIRECTIONAL ANTENNA
SFP-1000LX
LX GIG FIBER DDM SFP TRANSCEIVER
SFP-1000SX
SX GIG FIBER DDM SFP TRANSCEIVER
SFP-1000ZX
ZX GIG FIBER DDM SFP TRANSCEIVER
SFP-100FX
100BASE-FX FIBER DDM SFP TRANSCEIVER
WIREVIEW 1
WIREVIEW WIREMAPPER #1
WIREVIEW 2-6
WIREVIEW CABLE ID SET 2 THRU 6
Bundles
Model
Description
1TG2-1500/GLD
ONETOUCH AT G2 1500 AND 1 YR GOLD SUPPORT
1TG2-3000/GLD
ONETOUCH AT G2 3000 AND 1 YR GOLD SUPPORT
1T10G-1000/GLD
ONETOUCH AT 10G 1000 AND 1 YR GOLD SUPPORT
1TG2-3000-1T10G1M
ONETOUCH AT G2 3000 AND ONETOUCH AT 10G 1000 MODULE
1TG2-1500-LRAT2
ONETOUCH AT G2 1500 AND LINKRUNNER AT 2000
1TG2-3000-LRAT2
ONETOUCH AT G2 3000 AND LINKRUNNER AT 2000
1TG2-1500-2PK
ONETOUCH AT G2 1500 2-PACK
http://enterprise.netscout.com/node/126971/draft
16/17
5/9/2017
Datasheet: OneTouch™ AT G2 and 10G Network Assistant | NETSCOUT
Gold Support for Bundles
Model
Description
1TG2-1500-2PK-1YS
1 Year Gold Tools Support for 1TG2-1500-2PK
1TG2-1500-2PK-3YS
3 Year Gold Tools Support for 1TG2-1500-2PK
1TG2-1500-LRAT2-1YS
1 Year Gold Tools Support for 1TG2-1500-LRAT2
1TG2-1500-LRAT2-3YS
3 Year Gold Tools Support for 1TG2-1500-LRAT2
1TG2-30001T10G1M-1YS
1 Year Gold Tools Support for 1TG2-3000-1T10G1M
1TG2-30001T10G1M-3YS
3 Year Gold Tools Support for 1TG2-3000-1T10G1M
1TG2-3000-LRAT2-1YS
1 Year Gold Tools Support for 1TG2-3000-LRAT2
1TG2-3000-LRAT2-3YS
3 Year Gold Tools Support for 1TG2-3000-LRAT2
stechnikai
Az Ön méré
:
szakértője
kai Kft.
éréstechnily utca 12.
rá
EQUICOMpeM
ki
ás
ty
st, Má
1162 Buda
http://enterprise.netscout.com/node/126971/draft
m .h u
ww w. eq ui co .h u
m
in fo @ eq ui co
34
+36 1 272 12
17/17
Download PDF
Similar pages