CE-D970 - Clinton Electronics

The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Super DNR High Resolution
Color Dome Camera
CE-955-CAM-WD
CE-D970
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than those specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
1
Super DNR High Resolution Color Dome Camera
■ Contents
Features
4
Warnings and Precautions
5
How to Use the Camera
15
■ Function Menu Structure
15
■ How to Set up the Functions
16
Components
8
ㆍLENS
17
Names and Functions of Parts
9
ㆍEXPOSURE
19
ㆍWHITE BALANCE control
21
10
ㆍBACKLIGHT
22
11
ㆍDNR (Digital Noise Reduction)
24
11
ㆍDAY/NIGHT
25
■ SMPS
11
ㆍIMAGE ADJ
27
■ REMOTE CONTROLLER
11
ㆍSPECIAL
29
ㆍEXIT
33
■ Lens
10
■ OSD
■ VBS-EXTRA
■ SMPS
Installation
11
Dimensions
13
Troubleshooting
34
Cable Connections
14
Specifications
36
Super DNR High Resolution Color Dome Camera
2
3
Super DNR High Resolution Color Dome Camera
■ Features
Warning ■
Ultra High Resolution
Day & Night
The camera requires periodic inspection.
By adopting a 1/3" 410,000 pixel Sony CCD,
the camera produces clear picture quality with
a horizontal resolution of 580 TV lines for color,
and 700 TV lines for B/W.
The camera identifies whether it is day or night
and automatically switches to the appropriate
mode, depending on its environment. By day,
the camera switches to color mode in order to
maintain optimal color. At night, it switches to
B/W mode so as to obtain better picture definition.
Contact an authorised technician to carry out the inspection.
Miscellaneous Functions
Do not Install the camera on a surface that can not support it.
SYNC (INT/LL), SENS-UP, FREEZE, FLIP
(H/V-REV), D-ZOOM, SHARPNESS, MOTION
DETECTION and PRIVACY functions are provided.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Excellent Sensitivity
Adopting a Diagonal 6mm (1/3"), highly sensitive
CCD and digital signal processing technology,
it can clearly distinguish the outline and color
of a subject in an extremely low luminance
environment . even, for example, under starlight.
Since surveillance is possible in places where
the light is poor, the camera is appropriate for
day and night surveillance outdoors or on the
outside of buildings.
Built-in Coax and UTP video connections
OSD
The camera control is convenient by using
7 different foreign language O.S.D.
- NTSC : Korean, English, Spanish, Japanese
- PAL : English, French, German, Spanish,
Italian, Chinese
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
Motion Detection
The camera detects motion and generates a
screen message without an external sensor.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not hold plug with wet hands.
DNR (Digital Noise Reduction)
The amount of low illuminance noise has been
significantly reduced, and the signal-to-noise
ratio (S/N ratio) as well as horizontal resolution
have been improved, resulting in a clear and
sharp image display even in the dark.
Stop using your camera when you find it malfunctioning.
3 Axis built-in 100mm Dome Housing
with Adaptor Plate Bracket
DIS (Digital Image Stabilizer)
The DIS function compensates for any camera
movement, to produce more stable pictures.
Super DNR High Resolution Color Dome Camera
4
5
Super DNR High Resolution Color Dome Camera
■ Precautions
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Do not drop the camera or protect
it from physical shocks.
Only use the camera under conditions
where temperatures are between
-10˚C and +50˚C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
It can cause malfunctions to occur.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
Do not expose the camera to rain
or spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
Severe lighting change or flicker can
cause the camera to work improperly.
Super DNR High Resolution Color Dome Camera
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
6
Never keep the camera pointed
directly at strong light.
It can damage the CCD.
Do not expose the camera to
radioactivity.
If exposed to radioactivity the CCD
will fail.
ㆍIf the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
ㆍPlease check that the power satisfies the normal specification before
connecting the camera.
7
Super DNR High Resolution Color Dome Camera
■ Components
Names and Functions of Parts ■
1. COLOR DOME CAMERA
2. SCREWS
3. WIRE FOR VBS-EXTRA
4. INSTRUCTION GUIDE
Super DNR High Resolution Color Dome Camera
8
9
Super DNR High Resolution Color Dome Camera
■ Names and Functions of Parts
Names and Functions of Parts ■
① LENS : Vari-Focal DC Auto Iris Lens
③ VBS-EXTRA FOR CONNECTING TO LCD
Please use the supplied wire when connecting to LCD
VBS-EXTRA
④ 3 AXIS BRACKET
Please loosen screws and fix tilted and panned position.
⑤ SMPS PCB FOR DUAL POWER - IF APPLICABLE
⑥ REMOTE CONTROLLER
② OSD PCB
UP
SET
BA101
LEFT
RIGHT
DOWN
DIN1
CN4
( Optional Item )
● Jog Shuttle Switch
● SET : Used to access menu mode and for configuration.
- Push button : Used for the menu display. This button can be used to
: Moves cursor up the menu screen.
-
&
: Moves cursor left in the menu screen.
Parameter change
-
&
confirm settings after changing the value of the selected
function or current conditions.
: Used for selecting items by moving the cursor up or down
on the menu screen
: Used when changing item values, by moving the cursor to
the left or right on the menu screen.
Super DNR High Resolution Color Dome Camera
10
: Moves cursor down the menu screen.
: Moves cursor right in the menu screen.
Parameter change
11
Super DNR High Resolution Color Dome Camera
■ Names and Functions of Parts
DECORATION RING
DOME COVER
GIMBAL A'SSY
BASE HOUSING
■ Dimensions
1. Dome Base Mounting
- Open the dome by unscrewing the ring from the base-remove it
by unscrewing the ring and dome anti-clockwise.
- Mount the camera base to a sturdy surface using the supplied screws
and the premade holes on the base of the dome.
2. Power Connect & Monitor Impedance
- DC12V/300mA regulated power supply (DC12V only)
AC24V Class 2 power supply (AC24V/DC12V)
- To avoid fire or shock hazard, must use a UL listed power supply.
- Set the monitor impedance switch to 75Ω. Check the impedance
switch when the screen turns blurred.
3. Camera Module Adjustment
- Loosen screws for 3-axis camera bracket and adjust the direction
and angle of camera.
- Make sure to retighten the screws for camera bracket.
- Set any function you wish to activate by using the OSD buttons.
4. Dome Cover Mounting
- Replace the ring and dome by locating it on the base and turning
it clockwise.
5. When using UTP Cable
- Connect UTP(Unshield Twisted Pair) wire to the UTP output of the
camera directly. UTP transmitter is included in the camera therefore
additional UTP transmitter is not necessary.
- UTP receiver is necessary to connect UTP wire to Monitor or DVR.
- When connecting UTP wire, make sure the polarity of the video signal is correct.
- Use UTP wire "CAT 24AWG" to have the best transmission quality.
■ Cable Connections
POWER
73
.0 φ
100φ
105.5
55.0
125.79φ
Super DNR High Resolution Color Dome Camera
12
VIDEO(COAX)
DC only
VIDEO(UTP)
AC24V
DC12V
AC IN
DC IN
AC IN
DC IN
(unit : mm)
13
Super DNR High Resolution Color Dome Camera
How to Use the Camera
■ Installation
How to Use the Camera ■
On-Screen Display Menu Structure
Adapter Plate
Setup Menu
3.5x25 tapping
screw (provided)
Camera Body
• DC
EXPOSURE
• ATW
Dome Cover
* When installing on an adapter plate bracket.
① Place the adapter plate bracket on a flat installation surface and fix it with
the screws provided.
② When placing the camera body onto the plate, insert the plate pin into the
corresponding holes on the camera body as shown in figure-1. Lock the
camera in place by turning the camera body clockwise.
③ When placing the camera body on the plate, make sure that the power and
video cables are passed through.
④ After installation and adjustment of the camera is complete, secure the dome
cover by turning it clockwise.
Super DNR High Resolution Color Dome Camera
14
• MANUAL • AWC SET
• OUTDOOR • INDOOR
BACKLIGHT
• OFF
• BLC
DNR
• ON
• OFF
• COLOR
• B/W
• AUTO
• FREEZ
• V-REV
• H-REV
• D-ZOOM
• SHARPNESS
• HLC
• EXTERN
IMAGE ADJUSTMENT
(IMAGE ADJ.)
Locking
direction
• SENS-UP
• RETURN
DAY/NIGHT
Unlocking
direction
• MANUAL
• SHUTTER • AGC
WHITE BALANCE
Locking
direction
Unlocking
direction
LENS
• RETURN
SPECIAL
• CAMTITLE • SYNC
• MOTION DET
• PRIVACY • DIS
• COMM ADJ
• LANGUAGE • RESET • RETURN
EXIT
15
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
How to Set up the Functions
Settings can be made using the 5 buttons on the rear of the camera.
MAIN SETUP
Select the desired menu
item by using the UP and
DOWN buttons.
UP
BA101
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
Modes can be changed
using the LEFT and
RIGHT buttons.
7. IMAGE ADJ
LEFT
8. SPECIAL
RIGHT
9. EXIT
DOWN
DIN1
3. Set up a selected item by using the Left and Right buttons.
4. To finish and save the settings, select 'EXIT' and press the SET button.
CN4
1. Press the SET button.
• The Setup menu is displayed on the monitor screen.
MAIN SETUP
1. LENS
Note
• An item with the icon also has sub-menus. To select a sub-menu,
press the SET button.
• An item with the - - - icon has no sub-menus available for selection.
DC
2. EXPOSURE
3. WHITE BAL
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
7. IMAGE ADJ
8. SPECIAL
LENS
This function is used to adjust the brightness of the screen.
1. When the SETUP menu screen is displayed on the screen, position the
cursor to point to LENS using the Up and Down buttons.
2. Select the type of lens using the Left and Right buttons.
9. EXIT
MAIN SETUP
2. Select a menu item using the Up and Down buttons.
• Place the cursor over a desired item.
Super DNR High Resolution Color Dome Camera
16
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
17
ATW
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
EXPOSURE
● MANUAL : Manual Lens selection
MAIN SETUP
1. LENS
● DC : Auto Iris Lens selection
DC
2. EXPOSURE
3. WHITE BAL
Note
• The brightness of the screen can be adjusted in DC mode.
The brightness can be adjusted within the range of 1 ~ 70.
The optimum level of brightness for the user can be achieved by
adjustment.
• If you select the MANUAL mode, it can be adjusted in ESC mode.
3. Press the SET button if you wish to return to the previous menu
Super DNR High Resolution Color Dome Camera
18
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
1. When the SETUP menu screen is displayed select EXPOSURE using
the Up and Down buttons.
2. Select the desired mode using the Left and Right buttons.
● SHUTTER : Select either auto or manual shutter.
- A.FLK : Select this when picture flicker is expereinced, which can happen
when there is a clash with the frequency of the installed lighting.
- ESC : Select this to control the shutter speed automatically. If ESC is
selected, the shutter speed is automatically controlled according
to the ambient illumination available.
- MANUAL : The shutter speed is controlled manually.
19
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
White Balance (White Bal.)
Note
• When the SHUTTER is set to ESC, and the camera is set to Internal
Synchronisation, the picture may become unstable if the camera
faces a bright fluorescent light. Therefore, take care when choosing
the installation position.
• ESC and MANUAL modes are only available together when the lens
is set to MANUAL.
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP
is disabled.
● AGC (AUTO GAIN CONTROL):
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 0 to 24dB.
- HIGH : Allows automatic gain control from 0 to 42dB.
● SENS-UP :
When it is night or dark, the camera
automatically detects the light level and
maintains a clear picture if this mode is
activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
● RETURN :
Select this to save the changes in the EXPOSURE menu and return
to the SETUP menu.
Note
• If you press the SET button in 'AUTO' mode, You can adjust brightness
by increasing or decreasing the shutter speed. (X2~X256)
• Note that the higher the zoom level, the brighter the screen, but the
more likely it is that an after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP
operation when the zoom level is increased, this is normal.
Super DNR High Resolution Color Dome Camera
20
Use the White Balance function to adjust the screen colors.
1. Position the cursor to point to WHITE BAL on the SETUP menu screen
select using the Up and Down buttons.
2. Select the desired mode using the Left and Right buttons.
MAIN SETUP
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
ATW
4. BACKLIGHT
OFF
5. DNR
ON
※ Select one of the following 5 modes, as appropriate.
● ATW : Select when the color temperature is between 1800˚K and 10500˚K
● INDOOR : Select when the color temperature is between 4500˚K and 8500˚K
● OUTDOOR : Select when the color temperature is between 1800˚K and
10500˚K. (sodium light inclusion)
● AWC SET : To obtain the optimum state under the current luminance
levels, direct the camera to point toward a sheet of white
paper and press the SET button. If the environment changes,
including the light source, the white balance will require
re-adjustment.
● MANUAL : Select to "fine-tune" the White Balance manually. Set White
Balance first using the ATW or AWC mode. Afterwards
switch to MANUAL mode, fine-tune the White Balance
and then press the SET button.
21
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
Note
• Under the following conditions White Balance may not work properly.
In such cases, select the AWC mode.
① When the color temperature of the subject environment has a very
high temperature range (e.g. clear sky, or sunset)
② When the ambient illumination of the subject is low.
③ If the camera is directed toward a fluorescent light, or is installed in
a place where illumination changes dramatically, the White Balance
operation may become unstable.
BACKLIGHT
This camera is designed to deliver a clear and distinct image of both subject
and background, even when the subject is in backlit, using a proprietary
SV-IV DSP chip.
1. Position the cursor to point to BACKLIGHT on the SETUP menu screen
using the Up and Down buttons.
● BLC : Enables a user to directly select a desired area from a picture, and
to view the area more clearly.
BLC ON
BLC OFF
● HLC (High Light Compensation) :
If there is a high light installed in a limited environment such as an
apartment parking garage or gas station entrance, removing the
high light makes it possible to view car license plates efficiently.
- DAY : In normal daylight conditions, the HLC is not activated.
- NIGHT : If a high light that is larger than a certain size is present on
the screen, remove the high light to see license plates clearly.
HLC MASKING AREA
MAIN SETUP
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
HLC ON
HLC OFF
● OFF : Not being used
3. Select a desired mode using the Left and Right buttons and press the SET button.
● Select 'BLC' to adjust the area to be ● HLC : Enable a user to select a mask
enhanced and enhancement level.
color of high light area from a picture.
2. Select a desired mode using the Left and Right buttons depending on the
camera purpose.
Super DNR High Resolution Color Dome Camera
22
23
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
3. Set the DNR mode to 'ON' and press the SET button. The noise
reduction level can now be adjusted.
Note
• Because there can be a difference in the effectiveness of HLC
according to the amount of light area in the screen, optimize the
installation angle for the best HLC performance.
• In a dark environment, the HLC is only activated when a high light
that is larger than a certain area is present.
• The HLC is not activated in light or overly dark conditions.
Note
DNR
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select 'DNR' using the
Up and Down buttons.
MAIN SETUP
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
• You cannot set the DNR to 'ON' or 'OFF' when the AGC mode in the
EXPOSURE menu is 'OFF'.
• When adjusting the noise reduction level in DNR mode, remember
that the higher the level is set, the greater the reduction in noise level,
but it also increases the possibility of ghosting.
DAY/NIGHT
Pictures can be displayed in either color or black and white.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' using
the Up and Down buttons.
MAIN SETUP
1. LENS
DC
7. IMAGE ADJ
2. EXPOSURE
8. SPECIAL
3. WHITE BAL
9. EXIT
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
2. Select a desired mode using the Left and Right buttons.
● OFF : Deactivates DNR. Noise is not reduced.
● ON : Activates DNR so that noise is reduced.
Super DNR High Resolution Color Dome Camera
24
ATW
7. IMAGE ADJ
8. SPECIAL
9. EXIT
25
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
2. Select the desired mode using the Left and Right buttons.
● COLOR : The picture is displayed in color.
● B/W : The picture is always displayed in black and white.
● AUTO : This camera has an IR Cut-Filter and automatically
changes to the appropraite mode according to lighting
levels.To set up the switching time and switching speed
for the AUTO mode press the SET button.
IMAGE ADJ.
1. When the SETUP menu screen is displayed, select 'IMAGE ADJ.' using
the Up and Down buttons.
MAIN SETUP
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
● EXTERN : This mode allows the application of a filter to external signals.
2. Select the desired mode using the Left and Right buttons.
IMAGE SETUP
Note
1. FREEZE
OFF
• The DAY/NIGHT menu cannot be controlled when AGC in the
EXPOSURE menu is 'OFF'.
If so, the changeover between DAY mode and NIGHT mode
operates the same as selecting 'COLOR' mode.
2. V-REV
OFF
3. H-REV
OFF
• The OSD keys do not work for 3 seconds after switching to Color
or B/W. This is to ensure a stable camera operation.
6. RETURN
4. D-ZOOM
OFF
5. SHARPNESS
ON
● FREEZE : View still pictures.
● V-REV : Flips the picture vertically on the screen.
● H-REV : Flips the picture horizontally on the screen.
Super DNR High Resolution Color Dome Camera
26
27
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
SPECIAL
● D-ZOOM : Digitally zooms, the range is x1~x10.
1. When the SETUP menu screen is displayed, select 'SPECIAL' using the
Up and Down buttons.
MAIN SETUP
1. LENS
DC
2. EXPOSURE
3. WHITE BAL
● SHARPNESS : As this value is increased the picture outline becomes
stronger and clearer.
ATW
4. BACKLIGHT
OFF
5. DNR
ON
6. DAY/NIGHT
AUTO
7. IMAGE ADJ
8. SPECIAL
9. EXIT
2. Select the desired mode using the Left and Right buttons.
SPECIAL
1. CAM TITLE
● RETURN : Select this to save the settings for the IMAGE ADJ. menu
and to return to the SETUP menu.
INT
3. MOTION DET
OFF
4. PRIVACY
OFF
5. DIS
OFF
6. COMM ADJ
Note
7. LANGUAGE
• When H-REV or V-REV is selected, any text in the picture also will
be flipped horizontally or vertically.
• If the SHARPNESS level is increased too high the picture may
become distorted, or noise may generated.
Super DNR High Resolution Color Dome Camera
OFF
2. SYNC
28
ENGLISH
8. RESET
9. RETURN
● CAM TITLE : If a title is entered, the title appears on the monitor.
① When the SPECIAL menu screen is displayed, use the Up and
Down buttons to point the cursor to 'CAM TITLE'.
29
Super DNR High Resolution Color Dome Camera
■ How to Use the Camera
② Set to 'ON' using the Left and Right buttons.
Note
SPECIAL
• When the CAM TITLE menu is
'OFF', no title will be displayed
on the monitor screen even if
one has been entered.
1. CAM TITLE
OFF
2. SYNC
INT
3. MOTION DET
OFF
4. PRIVACY
OFF
5. DIS
OFF
⑤ Enter a title, move the cursor to 'POS' and press the SET button. The
entered title appears on the screen. Select the position to display the
title on the screen using the 4 directional buttons and press the SET button.
When the position is determined, select 'END' and press the
SET button to return to the SPECIAL menu.
6. COMM ADJ
7. LANGUAGE
ENGLISH
8. RESET
9. RETURN
③ Press the SET button.
Camera ID
AB C DE F GHI J KL M
N O P Q R S T U V WX Y Z
abcdef ghi j kl m
n o p q r s t u v wx y z
- . 1 2 3 4 5 6 7 8 9
→ ← CL R P OS E ND
● SYNC : In areas where the supply is 60Hz,
synchronise the output phase of
multiple cameras using the power
synchronization function (Line-Lock),
without using a synchronisation signal
generator.
- INT : Internal Synchronisation Type
- L/L : Power Synchronisation Type, Line-lock
• Press the SET button.
• Select a phase between 0 and 359.
Note
④ Use the 4 direction buttons to move to a character and select
it by pressing the SET button. Repeat this action to enter multiple
characters. Up to 15 alphanumeric characters can be used.
Note
• If the cursor is moved to CLR and the SET button pressed, all letters
are deleted. To edit a letter, change the cursor to the bottom left arrow
and press the SET button. Move the cursor over the letter to be edited,
move the cursor to the letter to be inserted and then press the SET button.
Super DNR High Resolution Color Dome Camera
30
• When using AC power at a 60Hz frequency Line-Lock synchronisation
can be used.
• When the power is DC 12V, the SYNC. menu is fixed to the 'INT' mode.
● MOTION DET:
This camera displays an on-screen message
whenever motion is detected.
31
Super DNR High Resolution Color Dome Camera
How to Use the Camera ■
■ How to Use the Camera
① When the SPECIAL menu screen is displayed, press the Up and Down
buttons so that the cursor points to MOTION DET.
② Set up the function using the 4 directional buttons.
- SENSITIVITY : Select up to eight MD areas. When the SENSITIVITY
value is high, motion detection sensitivity is increased to recognise
small movements.
- AREA MODE : Determines whether to use the MD area selected in
SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to
be used.
- YPOS : Determines the co-ordinates of the vertical axis for SEL POS.
- XPOS : Determines the co-ordinates of the horizontal axis for SEL POS.
- FILL→ SET : Fills in a selected MD area. Fills in a selected MD area.
The color of filling is sequentially selected as brown, orange, blue, cyan,
yellowish green, yellow and red.
- RETURN : Select this to save the MOTION DET menu settings and
return to the SPECIAL menu.
Note
• MD areas show only on the MOTION DET menu. Therefore, MD
areas are not displayed on the monitor screen.
● PRIVACY : Hide an area so that it is not
displayed on the monitor.
① When the SPECIAL menu screen is
displayed, press the Up and Down buttons
so that the cursor points to 'PRIVACY'.
② Set up the using the 4 directional buttons.
- AREA SEL : Up to 8 areas are selectable.
- AREA MODE :
Determines whether to use the area selected
in the AREA SEL, and the size and position of
the area.
Super DNR High Resolution Color Dome Camera
32
- MASK COLOR : Determine area color. Select Grey, Green, Red, Blue,
Black or White.
- TRANSP : Determine the transparency of the selected area, the range
is number from 0 to 3.
- RETURN : Select this to save the PRIVACY menu settings and return to
the SPECIAL menu.
● DIS (Digital Image Stabiliser) :
This function mitigates picture movement caused by external factors, such as wind.
● COMM ADJ (Communication Adjustment) :
This function sets up the camera communication
status when controlling the camera through an
external device.
① When the SPECIAL menu screen is displayed,
press the Up and Down buttons so that the
cursor points to 'COMM ADJ'.
② Set up the mode using the 4 direction buttons.
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE : Select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : Select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determines whether to send a command back to the controller
device when a communication control command is sent to the camera.
- DISP CAM ID : Display the camera title on the top left corner of the screen.
● LANGUAGE : Select the appropriate menu language.
● RESET : Resets the camera settings to the factory defaults.
● RETURN : Select this to save the SPECIAL menu settings and return to the
SPECIAL menu.
EXIT
Press the SET button in the EXIT menu to save the current settings and exit
the SET menu.
33
Super DNR High Resolution Color Dome Camera
■ Troubleshooting
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorised technician.
Problem
Nothing appears on
the screen.
Solution
• Check the power connections.
• Check the VIDEO signal line connection.
The image on the
screen is not clear.
• Make sure the lens is clean. Clean the lens with a
soft clean lint free cloth.
• Adjust the monitor contrast & brightness controls.
• Re-position the camera if necessary.
The image on the
screen is dark.
• Adjust the contrast control of the monitor.
• If you have an intermediate device, set the 75 / Hi-z
properly.
Problem
Solution
The Motion Detection
function does not
work.
• Check that MOTION DET in the SPECIAL SETUP
is not set to 'OFF'.
Color is not correct.
• Check the WHITE BAL settings in the SETUP menu.
The screen flickers
continually.
• Check that the camera isn't facing toward a bright
luignh. t source, such as the Sun.
The camera is not working • Check that an appropriate power source is
properly, and the surface
connected to the camera.
of the camera is hot.
The DAY/NIGHT menu
does not work.
• Check that AGC in the EXPOSURE menu is set
to 'OFF'.
The SENS-UP function
does not work.
• Check that AGC in the EXPOSURE menu is not
set to 'OFF'.
• Check that SHUTTER in the EXPOSURE menu
is not set to 'A.FLK' or 'MANUAL'.
Super DNR High Resolution Color Dome Camera
34
35
Super DNR High Resolution Color Dome Camera
■ Specifications
NTSC
Power Source
Size
CCD Total Pixels
Effective Pixels
Scanning System
Sync Synchronization
Frequency
O.S.D
Backlight Comp.
Resolution
S/N (Y signal)
Min. Illumination
White Balance
Electronic Shutter
E Speed
L
E Sens-up
C Gain Control
T DNR
R Motion Detection
I Privacy
C
A V-REV
L H-REV
Freeze
Sharpness
Day & Night
DIS
Digital Zoom
Operating Temperature / Humidity
Storing Temperature / Humidity
Weight
PAL
AC24V / DC12V DC12V
AC24V / DC12V
DC12V
220mA(AC24V)/260mA(DC12V) 160mA 220mA(AC24V)/260mA(DC12V) 160mA
SONY 1/3" Super HAD High Sensitivity Color CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
2:1 Interlace
Internal / Line Lock
Horizontal : 15.734 KHz, Vertical:59.94 Hz Horizontal : 15.625 KHz, Vertical:50.00 Hz
Korean, English, Japanese, Spanish English, French, German, Spanish,
Italian, Chinese
OFF/BLC/HLC
Color : 580 TV Lines
B/W : 700 TV Lines
52 dB (AGC Off, Weight ON)
0.15Lux(40IRE Color), 0.0006Lux(40IRE Sense-upX256)
ATW / AWC / Manual / Outdoor / Indoor (1800˚K ~10,500˚K)
1/60 ~ 1/120,000 sec
1/50 ~ 1/120,000 sec
AUTO / OFF (Selectable x2 ~ x256)
LOW / HIGH / OFF
ON / OFF (1~32 Level)
ON / OFF (8 Zone, ALARM Output)
ON/OFF (8 Zone)
ON / OFF
ON / OFF
ON / OFF
ON/OFF (Level Adjustable)
COLOR / Black & White / AUTO / EXT
OFF / ON
OFF / ON(x10)
-10˚C to +50˚C / 30% to 80% RH
-20˚C to +60˚C / 20% to 90% RH
Appro. 350g
Super DNR High Resolution Color Dome Camera
36
Download PDF
Similar pages