INFIAMMABILITY
PENSKY-MARTENS
750/BIS
ASTM D93 ASTM E134 IP 34 ISO 2719 EN 22719 FLASH POINT BY
PENSKY-MARTENS CLOSED CUP TESTER (740, 750, 755, 760)
This test method covers the determination of the flash point of petroleum
products in the temperature range from 40 to 360oC. Procedure A is
applicable to distillate fuels (diesel, kerosene, heating oil, turbine
fuels), new lubricating oils, and other homogeneous petroleum liquids
not included in the scope of Procedure B. Procedure B is applicable
to residual fuel oils, cutback residual, used lubricating oils, mixtures
of petroleum liquids with solids, petroleum liquids that tend to form
a surface film under test conditions, or are petroleum liquids of such
kinematic viscosity that they are not uniformly heated under the stirring
and heating conditions of Procedure A.
ASTM D3934 ISO 1516 FLASH/NO FLASH TEST - EQUILIBRIUM
METHOD BY A CLOSED CUP APPARATUS (740, 750, 755, 760)
This test method covers the determination of whether a liquid complies
with the closed-cup flash point requirements in government regulations,
or in specifications, or as agreed between the purchaser and the seller,
is limited to a temperature range between 0 and 110°C
ASTM D3941 IP 304 ISO 1523 FLASH POINT BY EQUILIBRIUM
METHOD WITH A CLOSED CUP APPARATUS (740, 750, 755, 760)
This test method covers the determination of the flash point of liquids in
which the specimen and the air/vapor mixture above it are approximately
in temperature equilibrium, is limited to a temperature range between 0
and 110°C
740
GAS PENSKY-MARTENS
Gas heated with Meker lamp, fitted with flame filter and safety valve.
Calibrated brass crucible, cover with gas ignition device allowing to ignite
the testing sample by a manual trip-opening. Stirring is manual, air bath
made in brass with external stainless steel calotte.
750/E
755/BIS
DIGITAL ELECTRIC PENSKY-MARTENS A AND B
PROCEDURES
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass crucible, cover with
gas ignition device allowing to ignite the testing sample by a manual tripopening. Motor stirrer for Procedure A and B, air bath made in brass with
external stainless steel calotte. Digital thermometer with thermocouple.
760/E
ELECTRIC PENSKY-MARTENS (3 PLACES)
760/BIS
DIGITAL ELECTRIC PENSKY-MARTENS (3 PLACES)
ACCESSORIES
12-0011
GEARED ELECTRIC MOTOR, 250 RPM (for 750/E)
10-0748
GAS CYLINDER
Empty, 3kg
10-0749
GAS REDUCER
30mbar
10-0750
RUBBER TUBE-JOINT AND TUBE, 5mt
T-AS9C
THERMOMETER ASTM 9C IP 15C (for 750/E)
T-AS10C
THERMOMETER ASTM 10C IP 16C (for 750/E)
SPARE PARTS
15-0741
CALIBRATED BRASS CRUCIBLE
15-0742
MOVEMENT COMPLETE
11-0022
HEATER
15-0745
MEKER LAMP (for 740)
15-0746
GAS MANTLE FLAME DAMPER, pack of 5 (for 740)
15-0751
SILICONE TUBING, 5mt
15-0752
THERMOMETER COLLAR, pack of 5 (for 740, 750/E)
15-0753
FLEXIBLE STIRRER DRIVE
12-0010
100RPM GEARED ELECTRIC MOTOR
12-0011
250RPM GEARED ELECTRIC MOTOR
12-0020
GEARED ELECTRIC MOTOR (for 755/BIS)
15-0110
ELECTRONIC REGULATOR
14-0003
THERMOCOUPLE K
16-0024
DIGITAL THERMOMETER
750/E
ELECTRIC PENSKY-MARTENS ASTM D93 E134
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass crucible, cover with
gas ignition device allowing to ignite the testing sample by a manual
trip-opening. Motor stirrer for Procedure A, air bath made in brass with
external stainless steel calotte.
750/BIS
DIGITAL ELECTRIC PENSKY-MARTENS
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass crucible, cover with
gas ignition device allowing to ignite the testing sample by a manual
trip-opening. Motor stirrer for Procedure A, air bath made in brass with
external stainless steel calotte. Digital thermometer with thermocouple.
20
750/AUT
AUTOMATIC PENSKY-MARTENS ASTM D93 D3941
E502 IP 34 ISO 2719 EN 22719 DIN 51758
Testing unit equipped with two ignition systems, electrical system or flame
exposure device, measurement of the ignition is detected by an ionisation
detector. When the sample reaches the selected test temperature, the
shutter opens and the ignition system introduces itself automatically. If the
the flash point is reached, the detection is done by an ionisation detector;
if not, the shutteer closes again and the sample continues to warm up
until the next test temperature. Supplied with software Windows® based,
user friendly interface, all analytical parameters recoded, customisable
analysis parameters and methods, customizable results report, printable
graphs and results, self-identification of the typology of the analysers
connected, audible alarm and displayed messages (at the end of the
analysis and in case of errors and/or malfunctions).
INFIAMMABILITY
SPARE PARTS
15-0754
ELECTRICAL IGNITION
15-0755
GAS IGNITOR
15-0756
PROBE PT100 FOR SAMPLE
15-0757
DETECTION CABLE
15-0758
PROBE PT100 FOR BATH
11-0750/AUT HEATER
820/BIS
DIGITAL ELECTRIC ABEL FLASH POINT EN ISO 13736
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass crucible, cover with gas
ignition device allowing to ignite the testing sample by a manual glideopening. Motor stirrer, air bath and water bath are made in chromiumplated copper. Digital thermometer with thermocouple. With internal
cooling coil.
750/AUT
830
GAS ABEL FLASH POINT EN ISO 13736
LPG heated with microbunsen fitted with safety valve. Calibrated brass
crucible, cover with gas ignition device allowing to ignite the testing
sample by a manual glide-opening, manual stirrer, air bath and water
bath are made in chromium-plated copper. With internal cooling coil.
ACCESSORIES
485/45
LOW TEMPERATURE THERMOSTATIC BATH AND
CIRCULATOR UP TO -45°C
10-0748
GAS CYLINDER
Empty, 3kg.
10-0749
GAS REDUCER
30mbar
10-0750
RUBBER TUBE-JOINT AND TUBE, 5mt
T-IP74C
THERMOMETER IP 74C
T-IP75C
THERMOMETER IP 75C
T-IP2C
THERMOMETER IP 2C
SPARE PARTS
15-0821
CALIBRATED BRASS CRUCIBLE
15-0822
MOVEMENT COMPLETE
15-0823
MICOBUNSEN (for 830)
15-0746
GAS MANTLE FLAME DAMPER, pack of 5 (for 830)
15-0751
SILICONE TUBING, 5mt
15-0752
THERMOMETER COLLAR, pack of 5 (for 820, 830)
15-0753
FLEXIBLE STIRRER DRIVE
15-0113
ELECTRONIC REGULATOR
14-0003
THERMOCOUPLE K
11-0820
HEATER
16-0024
DIGITAL THERMOMETER
ABEL FLASH POINT
IP 170 (obs) ISO 13736 FLASH POINT BY ABEL CLOSED CUP
METHOD (820, 830)
Determines the closed cup flash point of petroleum products and other
liquids having flash points between -30°C and 71°C inclusive
820
820
ELECTRIC ABEL FLASH POINT ISO 13736
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass crucible, cover with gas
ignition device allowing to ignite the testing sample by a manual glideopening. Motor stirrer, air bath and water bath are made in chromiumplated copper. With internal cooling coil.
820/AUT
AUTOMATIC ABEL FLASH POINT EN 924 EN 13736
IP 170 IP 491 IP 492 ISO 1516 ISO 3679 ISO 13736
Testing unit equipped with two ignition systems, electrical system or
flame exposure device, measurement of the ignition is detected by an
ionisation detector. The sample is warmed up according to the methods.
When the sample reaches the selected test temperature, the shutter
is opened and the ignition system introduces itself automatically. If the
flash point is reached, the detection is done by an ionisation detector.
If not, the shutter closes again and the sample continues to warm up
until the next test temperature. Supplied with software Windows® based,
user friendly interface, all analytical parameters recoded, customisable
analysis parameters and methods, customizable results report, printable
graphs and results, self-identification of the typology of the analysers
connected, audible alarm and displayed messages (at the end of the
analysis and in case of errors and/or malfunctions).
820/AUT
21
INFIAMMABILITY
CLEVELAND
ASTM D92 IP 36 DIN 51376 ISO 2592 FLASH AND FIRE POINT BY
CLEVELAND OPEN CUP TESTER (880, 890, 900, 880/AUT)
This test method describes the determination of the flash and fire point
of petroleum products with flash points above 79°C (175°F) and below
400°C (752°F) except fuel oils
ACCESSORIES
10-0748
GAS CYLINDER
Empty, 3kg
10-0749
GAS REDUCER
30mbar
10-0750
RUBBER TUBE-JOINT AND TUBE, 5mt
T-AS11C
THERMOMETER ASTM 11C IP 28C
SPARE PARTS
15-0823
MICROBUNSEN (for 900)
15-0746
GAS MANTLE FLAME DAMPER, pack of 5 (for 900)
15-0751
SILICONE TUBING, 5mt
15-0911
CALIBRATED BRASS CUP
15-0916
GAS IGNITION DEVICE, pack of 3
15-0110
ELECTRONIC REGULATOR
11-0022
HEATER
16-0025
DIGITAL TIMER (for 990)
880
880
ELECTRIC CLEVELAND ASTM D92
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass cup, gas ignition
device fitted with a pivot manually passing through the cup. Fitted with
pincers for thermometer.
880/AUT AUTOMATIC CLEVELAND
Testing unit equipped with 2 electrical ignitors and a pilot flame, with
automatic flame exposure device, measurement of the ignition is
detected by an ionisation detector. When the sample reaches the
selected test temperature, the flame is passed automatically above
the sample.When the flash point is reached, the detection is done by
an ionisation detector. For fire point detection, the sample continues
to be heated until permanent flame is detected by the second PT100
probe, then the auto extinguisher will be placed on the top of the test
cup. Supplied with software Windows® based, user friendly interface, all
analytical parameters recoded, customisable analysis parameters and
methods, customizable results report, printable graphs and results, selfidentification of the typology of the analysers connected, audible alarm
and displayed messages (at the end of the analysis and in case of errors
and/or malfunctions).
SPARE PARTS
15-0884
ELECTRICAL IGNITION
15-0885
GAS IGNITION
15-0886
PROBE PT100 FOR FLASH POINT
15-0887
DETECTION CABLE
15-0888
PROBE PT100 FOR FIRE POINT
11-0880/AUT HEATER
890
880/AUT
890
SEMIAUTOMATIC ELECTRIC CLEVELAND ASTM D 92
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Calibrated brass cup, gas ignition
device fitted with a pivot passing through the cup controlled by digital
timer. Fitted with pincers for thermometer.
880/4
ELECTRIC CLEVELAND (4 PLACES)
890/4
SEMIAUTOMATIC ELECTRIC CLEVELAND (4 PLACES)
900
GAS CLEVELAND ASTM D 92
Gas heated with microbunsen fitted with safety valve. Calibrated brass
cup, gas-ignition device fitted with a pivot manually passing through the
cup. Fitted with pincers for thermometer.
22
INFIAMMABILITY
TAG CLOSED
ASTM D 56 IP 491 IP 492 ISO 1310 ISO 1516 FLASH POINT BY TAG
CLOSED TESTER (920, 930)
This test method covers the determination of the flash point of liquids
with a viscosity below 5.5 mm2/s (cSt) at 40°C (104°F), or below 9.5
mm2/s (cSt) at 25°C (77°F), and a flash point below 93°C (200°F)
930/AUT
ASTM D 3934 FLASH/NO FLASH TEST - EQUILIBRIUM METHOD BY
A CLOSED CUP APPARATUS (920, 930)
This test method covers the determination of whether a liquid complies
with the closed-cup flash. This test method is limited to a temperature
range between 0 and 110°C (32 and 230°F)
ASTM D 3941 FLASH POINT BY EQUILIBRIUM METHOD WITH A
CLOSED CUP APPARATUS (920, 930)
This test method covers the determination of the flash point of liquids in
which the specimen and the air/vapor mixture above it are approximately
in temperature equilibrium. This test method is limited to a temperature
range between 0 and 110°C (32 and 230°F)
TAG OPEN
930
ASTM D 1310 FLASH POINT AND FIRE POINT OF LIQUIDS BY TAG
OPEN CUP APPARATUS (940, 950)
This test method covers the determination of the flash point and fire
point of liquids having flash points between -18 and 165°C (0 and 325°F)
and fire points up to 165°C
ASTM D 3143 FLASH POINT OF CUTBACK ASPHALT (940, 950)
This test method covers the determination of flash points of cut-back
asphalts having flash points of less than 93°C (200°F).
930
ELECTRIC TAG CLOSED ASTM D 56 D 3934 D 3941
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Test copper cup equipped with glidedevice and gas-ignition. Waterbath and support-jacket made in brass.
With internal cooling coil.
920
GAS TAG CLOSED ASTM D 56 D 3934 D 3941
Gas heated with microbunsen fitted with safety valve. Test copper cup
equipped with glide-device and gas-ignition. Waterbath and supportjacket made in brass. With internal cooling coil.
ACCESSORIES
485/20
LOW TEMPERATURE THERMOSTATIC BATH AND
CIRCULATOR UP TO -20°C
10-0748
GAS CYLINDER
Empty, 3kg
10-0749
GAS REDUCER
30mbar
10-0750
RUBBER TUBE-JOINT AND TUBE, 5mt
T-AS57C
THERMOMETER ASTM 57C
T-AS9C
THERMOMETER ASTM 9C IP 15C
SPARE PARTS
15-0823
MICROBUNSEN (for 920)
15-0746
GAS MANTLE FLAME DAMPER, pack of 5 (for 920)
15-0751
SILICONE TUBING, 5mt
15-0932
COPPER CUP, pack of 2
15-0933
COMPLETE MOVEMENT
11-0022
HEATER
15-0110
ELECTRONIC REGULATOR
930/AUT
AUTOMATIC TAG CLOSED ASTM D56 D3278 D3934
D3941 IP 304 IP 491 IP 492 ISO 1516 ISO 1523 ISO 3679
Testing unit equipped with two ignition systems, electrical system or flame
exposure device, measurement of the ignition is detected by an ionisation
detector. When the sample reaches the selected test temperature, the
shutter opens and the ignition system introduces itself automatically. If the
the flash point is reached, the detection is done by an ionisation detector;
if not, the shutteer closes again and the sample continues to warm up
until the next test temperature. Supplied with software Windows® based,
user friendly interface, all analytical parameters recoded, customisable
analysis parameters and methods, customizable results report, printable
graphs and results, self-identification of the typology of the analysers
connected, audible alarm and displayed messages (at the end of the
analysis and in case of errors and/or malfunctions).
950
950
ELECTRIC TAG OPEN ASTM D 1310 D 3143
Electrically heated by electronic regulator, mounted on a case painted
with anti-acid epoxidic products. Test cup made in moulded glass, gas
ignition device with pivot passing manually over the cup. This item has a
water bath fitted with pincers for thermometer.
940
GAS TAG OPEN ASTMD 1310 D 3143
Gas heated with microbunsen fitted with safety valve. Test cup made in
moulded glass, gas ignition device with pivot passing manually over the
cup. This item has a water bath fitted with pincers for thermometer.
ACCESSORIES
485/20
LOW TEMPERATURE THERMOSTATIC BATH AND
CIRCULATOR UP TO -20°C
10-0748
GAS CYLINDER
Empty, 3kg
10-0749
GAS REDUCER
30mbar
10-0750
RUBBER TUBE-JOINT AND TUBE, 5mt
T-AS9C
THERMOMETER ASTM 9C IP 15C
T-AS33C
THERMOMETER ASTM 33C IP 20C
T-AS34C
THERMOMETER ASTM 34C IP 21C
T-AS35C
THERMOMETER ASTM 35C IP 59C
SPARE PARTS
15-0823
MICROBUNSEN (for 940)
15-0746
GAS MANTLE FLAME DAMPER, pack of 5 (for 940)
15-0751
SILICONE TUBING, 5mt
15-0951
GLASS CUP, pack of 2
15-0952
GAS IGNITION DEVICE, pack of 3
11-0022
HEATER
15-0110
ELECTRONIC REGULATOR
23
Download PDF
Similar pages