Annexure-A
PACKAGE-I (TOOL KIT/TOOLS)
S.NO.
NAME OF EQUIPMENT WITH SPECIFICATION
A.TOOL KIT FOR CARPENTER TRADE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
MEASURING TAPE, 3 MTR
MARKING KNIFE, 200 MM
CARPENTER SQUARE, 200 MM
SQUARE, BEVEL, 200MM
CARPENTER MARKING GUAGE,
CARPENTER MORTISE GUAGE
SAW HAND, 450 MM
SAW TENON, 300 MM
PLANE JACK METAL, 335x 50MM CUTTER
PLANE SMOOTHING METAL, 200x50 MM CUTTER
CHISEL FIRMER ( BEVEL EDGED ), 6,10,15,20,AND 21 MM
WIDTH ( 5 NO'S )
CHISEL MORTISE-6,10,15, MM ( 3No'S )
SCREWDRIVER ( CABINET MAKER ) , 300MM
MALLET MEDIUM SIZE
HAMMER CLAW , 500 GM
OIL STONE ( CARBORUNDUM )
(UNIVERSAL
SILICON CARBIDE COMBINATION ROUGH AND FINE ),
200x50x21 MM
HAND BRUSH FOR BENCH CLEANING ( 450 mm)
B TRAINING KIT FOR TRADE ICTSM
1
2
3
4
5
6
7
8
9
10
11
12
Connecting screwdriver 100 mm
Neon tester 500 V.
Screw driver set (set of 5 )
Insulated combination pliers 150 mm
Insulated side cutting pliers 150 mm
Long nose pliers 150 mm
Soldering iron 25 W. 240 V.
Electrician knife
Tweezers 100mm
Digital Multimeter
Soldering Iron Changeable bits 15 W
De- soldering pump
C- TRAINING KIT FOR TRADE ELECTRICIAN
1
Steel Tape, 15 m length
2
Plier Insulated, 150 mm
3
Plier Side Cutting, 150 mm
4
Screw Driver, 100 mm
5
Screw Driver, 150 mm
Electrician Connector, screw driver insulated handle thin
6
stem, 100 mm
7
Heavy Duty Screw Driver , 200 mm
Page No. 1
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
NAME OF EQUIPMENT WITH SPECIFICATION
Electrician Screw Driver thin stem insulated handle, 250
mm
9
Punch Centre , 150 mm X 9 mm
10
Knife Double Bladed Electrician
11
Neon Tester
12
Steel Rule 300 mm
13
Hammer, cross peen with handle
14
Hammer, ball peen With handle
15
Gimlet 6 mm.
16
Bradawl
17
Scriber (Knurled centre position )
18
Pincer 150 mm
D- TRAINING KIT FOR TRADE ELECTRONIC MECHANIC
1
Connecting screwdriver 100 mm
2
Neon tester 500 V.
3
Screw driver set (set of 5 )
4
Insulated combination pliers 150 mm
5
Insulated side cutting pliers 150 mm
6
Long nose pliers 150 mm
7
Soldering iron 25 W. 240 V.
8
Electrician knife
9
Tweezers 100mm
10
Digital Multimeter (3 ½ digit)
11
Soldering Iron Changeable bits 10 W
12
De- soldering pump
E- TRAINING KIT FOR TRADE COPA
8
1
Standard Screw Driver Set
F- TRAINING KIT FOR TRADE SEWING TECHNOLOGY
1
Measuring Tape 150 cm
2
Seam Ripper
3
Thimble
4
Tailor’s Card Scale Triangular
5
Tailors Square – Plastic
6
French Curve Set of three
7
Thread Cutter
8
Scale plastic 24”
G- TRAINING KIT FOR TRADE WELDER
1
2
3
4
5
6
7
Welding helmet fiber
Welding hand shield fiber
Chipping hammer with metal handle 250 Grams
Chisel cold flat 19 mm x 150 mm
Centre punch 9 mm x 127 mm
Dividers 200 mm
Stainless steel rule 300mm
Page No. 2
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
8
9
10
11
12
13
14
15
NAME OF EQUIPMENT WITH SPECIFICATION
Scriber 150 mm double point
Flat Tongs 350mm long
Hack saw frame fixed 300 mm
File half round bastard 300 mm
File flat 350 mm bastard
Hammer ball pane 1 kg with handle
Tip Cleaner
Try square 6”
G- TRAINING KIT FOR TRADE PLUMBER
1
Rule Steel 300 mm both in inch and mm
2
Rule Wooden 4 fold, 600 mm
3
Hacksaw Frame adjustable for 250 to 300 mm
4
Scriber 200 mm
5
Centre punch 100 mm
6
Chisel Cold, flat 20 mm
7
Hammer ball pein 800 grams
8
Hammer ball pein 50 grams
9
File flat rough 300 mm
10
Level spirit wooden 300 mm
11
Plumb bob 50 grams
12
Trowel C-125-I S: 6013
13
Stillson wrench 200 & 350 mm
14
Screw Driver 250 mm
15
Wooden Mallet small I S: 2022
16
Cutting pliers 200mm I S : 3650
17
Steel tape (5m)
NOTE : (1)- All the above metioned items must be of Make :
PIE/TAPARIA/STENLAY/INDER/ISI MARK (2)- Rates quoted for complete
tool kit will only be considered and not for Individual item.
H. ALLIED TOOLS
1
RULE SIX , 1 METRE (IN INCH & MM)
2
CONTRUCTION SCALE 1 METER
3
SPRING CALIPER INSIDE 150 MM
4
SPRING CALIPER OUT SIDE
5
WING COMPASS 300 MM.
6
TRAMMEL
7
SPRIT LEVEL 300 MM.
8
RIP SAW 600 MM.
9
CROSS CUT SAW MM
10
EYE SHIELD
11
FRET SAW FRAME 150 MM.
Page No. 3
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
NAME OF EQUIPMENT WITH SPECIFICATION
COMPASS SAW 350 MM.
ADZE 15 KG.
PLANE RAVVET ADJUSTABLE 250 MM. X METERS X 9 MM.
CUTTERS.
SPOKE SHAVES 50 MM. CUTTER
ROUTER PLANE
CABINET SCREPER 100 MM.
GAUGE CHISEL, FIRMER, 6,10,12,16,20,MM
GAUGE CHISEL, SCRIBING 6,10,12,16,20,MM.
BALL PEIN HAMMER 600 GRS.
CROSS PEIN HAMMER 600 GRS
SCREW DRIVER 450 MM.
SCREW DRIVER 250 MM.
SCREW DRIVER 150 MM.
PINCER 50 MM.
FILE HALF ROUND 2 ND CUT 250 MM.
FILE HALF ROUND WOOD RASP BASTAD MM.
HANDS DRILL 6 MM. CAPACITIES
RATCHEL BRACE 250 MM. SWAP
CENTRE BITS 6,8,10,12.
EXPANSION BIT SETS.
OIL CANS COMBINATION SIDE CUTTING PLIERS.
PLUNGER SAW SET / PISTOL GRIP TYPE.
NUMBER PUNCH 12 MM.
SLIP STONE 100 MM.
‘T’ BAR CRAMP 0.6 METER.
‘T’ BAR CRAMP 1.75 METER.
CARVING TOOLS SET.
GOGGLES PAIR.
GLASS CUTTER.
NAIL PUNCH.
SURFACE PLATE 600 X 600 MM.
Crimping tool (pliers)
Soldering Iron 25W
Magneto spanner set
Screw driver 150mm
Steel rule 150mm
Scriber straight 150mm
Soldering Iron 240W
Allen key set (set of 9)
Tubular box spanner (set of 6nos)
Magnifying lenses 75mm
Continuity tester
Page No. 4
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
54
55
56
57
NOTE :
NAME OF EQUIPMENT WITH SPECIFICATION
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
Soldering iron 10W
Cold chisel 20mm
Scissors 200mm
Handsaw 450mm
(1)- All the above metioned items must be of Make : PIE/TAPARIA/STENLAY/INDER/ISI MARK (2)Ratesmust be quoted for Individual item.
PACKAGE-2 (EM,ICTSM & COPA)
S.NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
NAME OF EQUIPMENT WITH SPECIFICATION
Server Computer
LAN Cards, Wi-fi LAN Cards
Power Meter
Crimping Tools
Motherboards (of different make)
Cabinets
Processors (of different make)
Optical Drives
LCD/LED/TFT Monitors
Blu-Ray drive and player
SMPS Trainer kit
UPS Trainer kit
Power electronics Trainer kit
Post error debugging card
SMPS Tester
PCI slot Testing tool
Hardware and Network Trainer Kit
Router
Managed Layer 2 Ethernet Switch 8/16/24 port
Managed Layer 3 Ethernet Switch 8/16/24 port
Network Training System
LAN Protocol Simulation and Analyser Software
Network and Internet security trainer
LAN cable tester
Network cables – UTP
Network Cables – coaxial, flat, ribbon
LAN Cards, wi-fi LAN Card
Connectors for cables
Power Meter
Media Convertor
8/16/24 port UTP jack panel
SC Couplers
SC Pigtails
RJ-45 connector
Fluke Meter
Crimping Tools
Switch with POE ports
POE adapters
Page No. 5
MAKE AND
RATES
SPECIFICATION INCLUSIVE OF
S.NO.
NAME OF EQUIPMENT WITH SPECIFICATION
39
40
Network Camera (Outdoor / Indoor)
Fibre Optics cable with LC connector
41
WEB CameraConnection : USBMicrophone type : monoFocus
type : fixedVideo capture : 1024 x 768 HDFrame rate : 30 fps or
higherOptical resolution : 5 M pixels or higher
42
Wireless Modem cum RouterFast internet transmission of upto
24 Mbps downstream, 1 Mbps upstream wireless speed upto
54 Mbps (802.11 g) , 300 Mbps (802.11 n) Wireless ON and
43
44
45
46
47
48
49
Wireless Access PointWireless LAN standard 802.11 n / 802.11
g/ 802s.11b , operating channels FCC :11 ETSI:13 Operating
DIGITAL I/C TRAINER :
BUILT IN POWER SUPPLY
PROVIDING REGULATED DC FOR OPERATION AT LEAST 8
LOGIC INPUTS SWITCHES AT LEAST 8 LED FOR
OBSERVING OUTPUT. STUDY OF BASIC GATES AND THEIR
TRUTH TABLES OR, AND, NOR, NANDN , EX-OR, EXNOR
GATES
RHEOSTATS VARIOUS VALUES AND RATINGS:
25 WATT/1-3K, 50 W/1-5K, 100 W/1-5K, 150 W/1-5K
SOLDERING AND DE-SOLDERING STATION WITH
NECESSARY ACCESSORIES :
SOLDERING
IRON,POWER CONSUMPTION 60W.INPUT VOLTAGE 170270 V TEMPERATURE RANGE 180 TO 270 V. TIP TO
GROUND RESISTANCE UNDER 2 OHMS. DESOLDERING
GUN 70 WATTS INPUT, 170-270 V AC, TEMP RANGE 180 C
TO 480 C . PUMP: DIAPHRAGM TYPE VACCUM 600 MM/HG.
SMD SOLDERING AND DESOLDERING STATION WITH
NECESSARY ACCESSORIES. HOT AIR SOLDERING &
DESOLDERING STATION FOR SMD WORK WITH
TEMPERATURE & AIR FLOW CONTROL
COMPUTER IN ASSEMBLED FORM LATEST
CONFIGURATION:
APPLICATION KITS FOR MICRO CONTROLLERS 6
DIFFERENT APPLICATIONS:
6 DIFFERENT
TYPES OF APPLICATION KITS FOR MICRO CONTROLLER.
Page No. 6
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
50
51
52
53
54
55
NAME OF EQUIPMENT WITH SPECIFICATION
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
UNIVERSAL TRANSDUCER TRINER ( UNIVERSAL
SENSOR/INSTRUMENT TRINER):
1
ON BOARD: LVDT, MICROPHONE, HALL SENSOR, STRAIN
GUAGE, ULTRASONIC TRANS RECEIVER, 2. TEMP
SENSOR; LM35, THERMISTOR, THERMOCOUPLE,
HUMIDITY SENSOR ETC.
3. LIGHT SENSOR:PHOTO DIODE, PHOTO DIODE, PHOTO TX., PHOTO
VOLTAIC CELL, PHOTO CONDUCTIVE CELL, LDR.
4. SIGNAL CONDITIONING: INSTRUMENTATION AMPLIFIER,
CLASS AMPLIFIER, DIFFERENTIAL AMPLIFIER.
5. SQUARE WAVE GENERATOR, BAND PASS FILTER,
VARIABLE RESISTOR: SERVO POTENTIOMETER, SLIDE
RESISTOR, ROTATRY RESISTER, WIRE WOUND, CARBON
TRACK.
6. BUZZER, VOLMETER ( 0-15V ), TEST
POINT ON EACH SECTIONS
FIBRE OPTICS COMMUNICATION TRINER
TRANSMITTER : 2 No., FIBREOPTICS LED HAVING PEAK
WAVELENGHT OF EMISSION 660 NM & 950 NM
RECEIVER : 2 No., FIBRE OPTICS PHOTO DETECTOR
MODULATION TECHNIQUES : 1. AM/ FM 2. PAM/PWM/PPM
DRIVERS: 1 No. WITH ANALOG & DIGITAL MODES AC
AMPLIFIER : 2 Nos. CLOCK : CRYSTAL CONTROLLED
CLOCK
PLL DETECTOR : 1 No. COMPARATOR :
2 Nos.
FILTERS : 2Nos. 4 ORDER
BUTTERWORTH.
ANALOG BAND WIDTH :
100 KHZ OR ABOVE FUNCTION GENERATOR : SINE WAVE (
AMPLITUDE ADJUSTABLE )
OPTICAL
POWER METER, 5 METER FIBER CABLE ( 650/660/950 NM )
10 METER FIBRE CABLE ( 650/660/950 NM )
LCD TV TRAINER KIT
LCD TV TRAINER KIT 21"
OR MORE HAVING TEST POINTS, FAULT SIMULATION
FACILITY ETC
LED TV TRAINER KIT
LED TV TRAINER KIT 21"
OR MORE HAVING TEST POINTS, FAULT SIMULATION
FACILITY ETC
SOLAR POWER INVERTER 500VA SOLAR POWER
INVERTER 500VA, WITH SUITABLE SOLAR PANEL FOR
BATTERY CHARGING, INVERTER UNIT, BATTERY
INCLUDED WITH AT LEAST 10 TO 15 MINUTE BACKUP
LED LIGHTING SYSTEM
LED LIGHTING SYSTEM,
6V BATTERY OPERATED, 40 OR MORE LED
PACKAGE - 3 (PLUMBER, CARPENTER & WELDER)
NAME OF EQUIPMENT `WITH MAKE AND SPECIFICATION
S. No
1
Bench type Drilling MachineWith all Accessories and
important spares
3 phase, min. 1
Page No. 7
HPDrilling Capacity in MS: about 20mmTapping in MS: about
15mmSpindle Travel: about 80mmdistance from spindle nose
MAKE AND
SPECIFICATION
RATES
INCLUSIVE OF
ALL TAXES IN
RS
S.NO.
1
2
3
4
NAME OF EQUIPMENT WITH SPECIFICATION
Bench type Drilling MachineWith all Accessories and
important spares
3 phase, min. 1
HPDrilling Capacity in MS: about 20mmTapping in MS: about
15mmSpindle Travel: about 80mmdistance from spindle nose
to table: 560mmDistance from spindle to centre of column:
about 152 mmTable Size: about 215X215 mmBase plate: about
235X360 mmFitted with suitable standard electricals,
necessary accessories and attachments
Double wheel PedestalGrinder
•Rated Input: 1 HP
•Grinding wheel Dia: 200 mm
•Grinding wheel width: 25 mm(Approx)
•Rough and smooth grinding wheels of Aluminum Oxide.
Power Hacksaw
with all accessories
•Motor Input: 1
HP, 3 Phase, 415V, 50Hz
•Blade size: 12"-14"
•Max capacity dia. Of Round bar:200mm
•Max. capacity of Square bar: 175
Fitted with suitable standard electricals, necessary accessories
and attachments
Manual Metal Arc Machine(Thyristorised/rectifier Type)With
all essential accessories and electrical
•Rated Input:
18KVA, 3 Phase, 415V, 50Hz
•Output Welding Current Range: 10-400A DC
•Open Circuit Voltage: 90V( max)
•Welding Current Max. : 400Amperes
•Cooling Type: Forced Air
•Current Control: Stepless
•Insulation Class: H
•Essential compatible accessories to be supplied with the
Machine: Electrode Holder, Earth Clamp, Earth Lead (10 m
min), welding Lead (10 m min).
Page No. 8
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
5
6
7
8
9
NAME OF EQUIPMENT WITH SPECIFICATION
Oxy-acetylene welding and cutting setwith all accessories
Oxygen filled Cylinder with oxygen regulator,
0-30 psi, Including test Certificate from authorisedagency .
•1 acetylene filled Cylinder with acetylene regulator, 0-30 psi,
Including test Certificate from authorised agency .
•Welding torch, cutting torch and nozzle set, Gas Lighter.
•Min 5m flexible hose pipe for each cylinder
•Trolley for gas cylinders.
Foot Operated Resistance Spot Welding Machine with all
accessories
•Rating: 20 KVA, 3 phase,
415V,50Hz.
•Nominal Throat Clearance: 200-250 mm
•Throat Depth: 500mm
•Max. electrode force @6Kg/cm2 : 450Kg.
•Fitted with suitable standard electrical, necessary
accessories and attachments
Double wheel Pedestal Grinder
•Rated Input: 1000
watt
•Grinding wheel Dia: 300 mm
•Grinding wheel width: 25 mm
•Rough and smooth grinding wheels of Aluminum oxide/Silicon
Carbide
• MS wheel guards.
Angle Grinder
•Rated Input:
1000 watt
•Disc Dia: 125mm
•05 Extra grinding wheels to be supplied with the equipment
TIG welding apparatus
•Power supply
: 3phase AC 380 V (±15%)
•Rated input current : approx. 27.6/20 amp
•Current range: 5-400 amps
•Rated output voltage: 36/26
•No load voltage : 68 V approx.
•Dimensions
: approx. 495X328X355 mm
•It should be supplied with an argon gas cylinder and Preheator
Page No. 9
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
10
11
12
13
14
15
16
17
18
19
20
21
22
NAME OF EQUIPMENT WITH SPECIFICATION
MIG welding apparatus
•Power supply
: 3 phase AC 380 V (±15%)
•Rated input current : approx. 27.6/20 amp
•Current range: 50-350 amps
•Rated output voltage: 36/26
•No load voltage : 68 V approx.
•Dimensions
: approx. 495X328X355 mm
•It should be supplied with an CO2 gas cylinder, Preheater,
and feeder pipe
Air Plasma Cutting Equipment
•Clear cut
ranging 15 - 25 mm capacity ,three phase ,duty cycles 100 , 612 Bar pressure ,Output current ranging from 60-80 Amps. And
having two cylinder 5HP air compressor , 8-12 Bar Pressure for
cutting different metals.
Bench Grinder
Wheel Dia 150
mm
Silicon carbide wheels.
Portable Drilling machine(Cap.6mm)
Max. drilling
capacity of 6mm ,0.5 Hp Bench type.
Portable Abrasive cut off Machine.
2Hp, 3 phase
with cutting capacity of 1 ½” dia for round bar and 1’’ for
square bar with coolant pump.
Electric PPR pipe welding machine
20-32 mm size
, 800-1000 Watt ,260 V, 260o C.
Electrode drying Oven
750-1000
Watt, 220 V Electrode length = 450 mm.
Inverter based Welding Machine
Single phase
,10KVA, 20-300 Amp. Current, 60 % duty .
Hydraulic pressure Machine
Apparatus For testing
leakagein domestic GI pipe fittings.
Lever Operated Hand Shearing machine
Shearing Capacity; upto 6mm thick sheet/flats
Hammering drilling machine
5-15 mm
Hammer Drill, 2-3 Kgs.
Welding process Simulators
For
SMAW/GTAW/GMAW having following features:-Position, speed, stick out and angle measurement.
-weld analysis on gaps, beads, porosity.
-Safety awareness.
- Multilevel graded learning approach.
Solar Water Heater System
200 LPD
Page No. 10
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
S.NO.
NAME OF EQUIPMENT WITH SPECIFICATION
23
Fire Extinguisher
Electric Start Fire type,
Powder type.
24
25
26
27
Moisture Meter
Electric Blower Portable
Electrical Drying Oven Small Type
Setup Turning Tools
28
29
30
31
32
33
34
35
RATES
MAKE AND
INCLUSIVE OF
SPECIFICATION ALL TAXES IN
RS
6Kg, ABC and
Mortising Machine (Combined Hollow Chisel and Chain Type)
Adjustable Saw Sharpner
Electric Cutter Machine For Wood Cutting
PORTABLE CIRCULAR SAW MACHINE
PORTABLE PLANING MACHINE
POWER DRILL MACHINE
PORTABLE ROUTER MACHINE
POWER SCREW DRIVER
PACKAGE-4 (SOFTWARES)
S.NO.
NAME OF EQUIPMENT WITH SPECIFICATION
1
2
3
4
5
6
7
Windows Server Operating System
Windows Operating System
Linux Operating System
Network Management Software
Data recovery software
LINUX Server Operating System (Samba / Su-se)
Open source Pc Utility / Tweak Software
8
9
10
11
12
13
14
15
MS Office 2010 (professional) or the latest version
(Single/Multi users)
Antivirus for – clients / workstations in profile with validity
of an year or more which should be renewed upon expiry
(Single/Multi users)
Open Office or equivalent.
GIMP / Irfan View Image editor or equivalent
WYSIWYG Web Authoring tool- Dreamweaver or
Opensource tools likeKompozer, FrontPageor similar tools
along with FTP tools for ex.Filezilla etc.
Tally ERP 9 or Latest(Single/Multi users)
E Commerce Simulation Software
Web Server : Any HTTP Web server / XAMPP or any other
similar server
Page No. 11
MAKE AND
RATES
SPECIFICATION INCLUSIVE OF
Download PDF
Similar pages