Model No. 831.24855.1
TR A
Serial No.
ILL
Write the serial number in the space
above for reference.
\
Serial
Number
Decal
• Assembly
• Operation
• Maintenance
• Part List and Drawing
Sears, Roebuck and Co., Hoffman Estates, IL 60179
TABLE OF CONTENTS
WARNING DECAL PLACEMENT ..............................................................
IMPORTANT PRECAUTIONS
................................................................
BEFORE YOU BEGIN ......................................................................
ASSEMBLY ...............................................................................
OPERATION AND ADJUSTMENT ............................................................
HOW TO FOLD AND MOVE THE TREADMILL ..................................................
TROUBLESHOOTING
.....................................................................
EXERCISE GUIDELINES ...................................................................
PART LIST ..............................................................................
EXPLODED DRAWING ....................................................................
ORDERING REPLACEMENT PARTS ..................................................
90 DAY FULL WARRANTY
..........................................................
2
3
5
6
14
20
22
25
26
28
Back Cover
Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s), If a decal is missing or
illegible, call 1-888-533-1333 and request
a free replacement decal. Apply the
decal in the location shown. Note: The
decal(s) may not be shown at actual size.
:
children on or
around treadmill,
•Remove key when
not in use,
.Keepclo_hbg,
lingers, and ha}r
• Never _y _o adjust
or Ii× the belt whle
it s mov.'g.
_]
2
atNefle shoes whle
.Always wear
operat ng treadmill,
iMPORTANT PRECAUTIONS
WARNING: Toreduce
the
.sk
ofse.ousnjury,
read
a, mportant
precautions
and=nstructions in this manual and all warnings on your treadmill before using your treadmill.
sumes no responsibUity for personal injury or property damage sustained by or through
this product.
.
.
.
4.
.
.
.
.
.
Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons
with pre-existing health problems.
it is the responsibility
of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
Use the treadmill
only as described.
Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
Do not operate the treadmi!l where aerosol
products are used or where oxygen is being
administered.
Keep children under age 12 and pets away
from the treadmill at all times.
The treadmill should be used only by persons
weighing 300 Ibs. (136 kg) or less.
Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
11. When connecting the power cord (see page
14), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
Sears asthe use of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications
described on
page 14. To purchase a surge suppressor, see
your local Sears store or call the telephone
number on the back cover of this manual and
order part number 146148, or see your local
electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill, if the control system is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppressor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 22 if the treadmill is
not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 16).
17. Never start the treadmill while you are stand=
ing on the walking belt. Always hold the
handrails while using the treadmilL
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general
20. Never leave the treadmill
unattended
while it
24. Inspect and properly tighten all parts of the
treadmill regularly.
is running. Always remove the key, unplug
the power cord, and switch the reseVoff circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
25.
DAN G E R:A ways
onp,og
the
power
cord immediatelyafteruse,beforecleaningthe
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood un=
less instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 Ibs. (20 kg)
to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE iNSTRUCTiONS
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM ®
XP TRAINER 580 treadmill. The XP TRAINER 580
ing this manual, please see the back cover of this
manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial number decal are shown on the front cover of this manual.
treadmill offers an impressive selection of features designed to make your workouts at home more enjoyable
and effective. And when you're not exercising, the
unique XP TRAINER 580 treadmill can be folded up,
requiring less than half the floor space of other treadmills.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Tray
Console
Pulse Sensor
Handrail
Key/Clip
Upright
Reset/Off
Breaker
Walking Belt
Foot Rail
--
Power Cord
Platform Cushion
Idler Roller
Adjustment Bolts
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires
the included h_
and your own Phillips screwdriver
adjustable
_,
pliers
wrench
needlenose
_
, and scissors
_
_
,
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: if a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included. If a part is missing, call 1-888-533-1333.
#8 x 1/2" Screw
(2)-6
3/8" Star
Washer (12)-4
#8 x 1/2" Ground
Screw (3)-1
5/16" Star
Washer (13)-4
#8 x 3/4" Screw
(1)-4
1/4" Star
Washer (14)-2
#8 x 1" Tek Screw
(4)-4
1/4" x 3/4" Bolt
(10)-2
5/16"x 1" Bolt (6)-6
#10 x 3/4" Screw
(5)-2
3/8" x 1 3/4" Bolt (8)-1
Base Foot Spacer
(89)-2
3/8" Nut (11)-3
3/8"x 2" Bolt (7)-3
3/8" x 4" Bolt (9)-4
1.
Make sure that the power cord is unplugged.
87
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (51) so that the treadmill is more stable;
do not fully fold the Frame yet.
79
84
4
Cut the shipping tie securing the Upright Wire
(79) to the Base (87). Locate the plastic tie in
the indicated hole in the Base, and use the tie to
pull the Upright Wire out of the hole.
Attach two Base Feet (84) to the Base (87) in the
locations shown with two Base Foot Spacers
(89) and two #8 x 1" Tek Screws (4).
Then, attach the other two Base Feet (84) with
two #8 x 1" Tek Screws (4).
_4
89
.
See the inset drawing.
the Upright Wire (79).
Cut the plastic tie near
2
Plastic Tie --
£,
Attach a Wheel (88) to the Base (87) with a 3/8"
x 2" Bolt (7) and a 3/8" Nut (11). Do not overtighten the Nut; the Wheel must turn freely.
;v
/
*
.
Identify the Right Upright (80) and the Right
Upright Spacer (82), which are marked with
stickers.
Insert the Upright Wire (79) through the Right
Upright Spacer (82) as shown. Set the Right
Upright Spacer on the Base (87).
2
/
J
87
80
79
Have a second person hold the Right Upright
(80) near the Base (87). See the inset drawing.
Tie the wire tie in the Right Upright securely
around the end of the Upright Wire (79). Then,
pull the other end of the wire tie until the Upright
Wire is routed completely through the Right
Upright.
Tie
,
Hold a Bolt Spacer (81) inside the lower end of
the Right Upright (80). Insert a 3/8" x 4" Bolt (9)
with a 3/8" Star Washer (12) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (81), 3/8" x 4" Bolt
(9), and 3/8" Star Washer (12).
4
9
80
79
Hold the Right Upright Spacer (82) and the
Right Upright (80) against the Base (87). Be
careful not to pinch the Upright Wire (79).
Tighten the 3/8" x 4" Bolts (9) until the heads of
the Bolts touch the Upright; do not fully tighten
the Bolts yet.
82
83
Press a Base Cap (83) into the Base (87).
,
With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (51) so that the treadmill is more stable;
do not fully fold the Frame yet.
Attach a Wheel (88) to the Base (87) with a 3/8"
x 2" Bolt (7) and a 3/8" Nut (11). Do not overtighten the Nut; the Wheel must turn freely.
5
51
.
Hold a Bolt Spacer (81) inside the lower end of
the Left Upright (75). Insert a 3/8" x 4" Bolt (9)
with a 3/8" Star Washer (12) into the Left
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (81), 3/8" x 4" Bolt
(9), and 3/8" Star Washer (12).
75
Hold the Left Upright Spacer (86) and the Left
Upright (75) against the Base (87). Tighten the
3/8" x 4" Bolts (9) until the heads of the Bolts
touch the Upright; do not fully tighten the
Bolts yet.
81
83
Press a Base Cap (83) into the Base (87).
With the help of a second person, tip the treadmill so that the Base (87) is flat on the floor.
.
Slide the Left Handrail Spacer (74) and the Right
Handrail Spacer (78) onto the top of the Left
Upright (75) and the Right Upright (80).
.
Insert the end of the Upright Wire (79) into the
bottom of the Right Handrail (104) and out of the
hole in the side of the Right Handrail.
8
107
Slide the Handrail Caps (105)onto the lower
ends of the Left Handrail (107) and the Right
Handrail (104). Then, insert the brackets on the
Handrails into the tops of the Uprights (75, 80).
Hole
79
Remove the wire tie from the Upright Wire (79).
105
9
g.
Attach the Left Handrail (107) and the Right
Handrail (104) with six 5/16" x 1" Bolts (6) and
four 5/16" Star Washers (13) as shown. Do not
fully tighten the Bolts yet.
13
Slide the Handrail Caps (105) away from the
Uprights (75, 80). Attach the lower end of each
Handrail (104, 107) to the Uprights with a #10 x
3/4" Screw (5).
105\
Orient the Handrail Caps (105) as shown.
Secure a Handrail Cap to each Handrail (104,
107) with a #8 x 1/2" Screw (2).
10. Set the console assembly face down on a soft
surface to avoid scratching the console assembly.
10
Console
Assembly
Remove the two #8 x 1/2" Screws (2) from the
Crossbar (106), and then remove the Crossbar.
Save the Crossbar and the two Screws for
steps 11 and 14.
10
11. Attach the Crossbar (106) to the Left and Right
Handrails (107, 104) with two 1/4" x 3/4" Bolts
(10) and two 1/4" Star Washers (14). Do not
tighten the Bolts yet.
11
07
106
104
12. Have a second person hold the console assembly near the Right Handrail (104) and the Left
Handrail (not shown). Connect the Upright Wire
(79) to the console wire. See the inset drawing.
The connectors should slide together easily
and snap into place. If they do not, turn one
connector and try again. IF THE CONNECTORS
ARE NOT CONNECTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN YOU
TURN ON THE POWER.
12
Console Assembly
Console_
Console
Wire
79 /
/
104
13. Attach the ground wire from the console assembly to the Right Handrail (104) with a #8 x 1/2"
Ground Screw (3). Note: It may be difficult to
turn the Ground Screw.
13
Console Assembly
Set the console assembly on the Right Handrail
(104) and the Left Handrail (not shown). Be
careful not to pinch the wires. Insert the connectors and the excess wire into the Right
Handrail.
Ground
Wire
__Wire
104 /
11
®
®_
14. Attach the console assembly to the Left and
Right Handrails (107, 104) and the Crossbar
(106) with four #8 x 3/4" Screws (1) and four #8 x
1/2" Screws (2). Start all eight Screws before
tightening them.
14
Console
Assembly
107
Tighten the six 5/16" x 1" Bolts (6) (only three
are shown).
Tighten the two 1/4" x 3/4" Bolts (10) (only one
is shown).
1
See assembly steps 4 and 6. Firmly tighten the
four 3/8" x 4" Bolts (9).
15. If necessary, press the Left Tray (94) and the
Right Tray (103) into the Console Back (98).
15
94
Tighten #8 x 1/2" Screws (2) into the Left
Handrail Spacer (74) and the Right Handrail
Spacer (78).
98
103
12
16. Raise the Frame (51) to the position shown.
Have a second person hold the Frame until
this step is completed.
16
Orient the Storage Latch (48) so that the large
barrel and the Latch Knob (49) are oriented as
shown.
Attach the upper end of the Storage Latch (48)
to the bracket on the Frame (51) with a 3/8" x 2"
Bolt (7) and a 3/8" Nut (11).
Attach the lower end of the Storage Latch (48) to
the Base (87) with a 3/8" x 1 3/4" Bolt (8), Note:
It may be necessary to move the Frame (51)
back and forth to align the Storage Latch with
the Base.
Barrel
87
Lower the Frame (51) (see HOW TO LOWER
THE TREADMILL FOR USE on page 21).
17. Make sure that all parts are properly tightened before you use the treadmill, if there are sheets of clear
plastic on the treadmill decals, remove the plastic, To protect the floor or carpet, place a mat under the treadmill, Note: Extra hardware may be included, Keep the included hex keys in a secure place; the large hex key
is used to adjust the walking belt (see pages 23 and 24).
13
OPERATION
THE PRE-LUBRICATED
AND ADJUSTMENT
WALKING
BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
IMPORTANT: The treadmill
GFCI-equipped outlets.
HOW TO PLUG IN THE POWER CORD
is not compatible
with
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
A DAN G ER: Improper
connection
of the equipment-grounding
conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product=if
it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
_,_Grounded
Outlet Box
i
Surge Suppressor
_:,'t "<
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home's power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local Sears store or call the telephone number
on the back cover of this manual and order part
number 146148, or see your local electronics store.
_j_
Grounding Pin
"--
Grounding Pin
Grounded Outlet
2
_Grounded
/ll _J I
_
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning
properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.
Grounding Plug
Outlet Box
Adapter
Surge suppressor
Metal Screw
_
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
This product must be grounded, if it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
grounded before using an adapter.
14
CONSOLEDIAGRAM
TIME
12-'
DISTANCE
CALORIES
2]
SPEED
I
5
MPM
6
STOP
\
FEATURES OFTHECONSOLE
To turn on the power, see page 16. To use the manual mode, see page 16. To use a preset workout,
see page 18. To use the information mode, see
page 19. To use the stereo sound system, see page
19.
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable.
When the manual mode of the console is selected, you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even measure your heart rate using the handgrip pulse sensor.
IMPORTANT: If there is a sheet of clear plastic on
the console, remove the plastic. To prevent damage to the walking platform, wear clean athletic
shoes while using the treadmill. The first time the
treadmill is used, observe the alignment of the
walking belt, and center the walking belt if necessary (see page 24).
In addition, the console offers sixteen preset workouts--four weight loss workouts, four aerobic workouts, four endurance workouts, and four performance
workouts. Each workout automatically controls the
speed and incline of the treadmill as it guides you
through an effective exercise session.
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
19. For simplicity, all instructions in this section refer to
miles.
You can even listen to your favorite workout music or
audio books with the console's premium stereo sound
system while you get in shape.
15
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
iMPORTANT: if the treadmill has been
cold temperatures, allow it to warm to
perature before turning on the power,
do this, you may damage the console
other electrical components.
Plug in the power cord (see
page 14). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
exposed to
room temif you do not
displays or
1.
insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2.
Select
the manual
mode.
When the key is inserted,
the manual mode will be
selected and a track will
Reset
Position
appear in the matrix. If a
preset workout has been
selected, remove the key
and then reinsert it.
power cord. Switch the circuit breaker to the reset position.
iMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store, if the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 19 to turn off the demo mode.
3.
Start the walking
m
m
Z
Z
mmm
belt.
To start the walking belt, press the Go button, the
Speed increase button, or one of the speed buttons numbered 1 through 10.
If you press the Go button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase
and decrease buttons. Each time you press a button, the speed setting will change by 0.1 mph; if
you hold down a button, the speed setting will
change in increments of 0.5 mph. Note: After you
press the buttons, it may take a moment for the walking belt to reach the selected speed setting.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 15)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.
If you press one of the numbered speed buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Go button, the
Speed increase button, or one of the speed buttons numbered 1 through 10.
16
4.
Change the incline of the treadmill
as desired.
Speed display--This
display shows the speed
of the walking belt.
To change the incline of
Incline
the
treadmill,increase
press andthedecrease buttons or one of
the numbered incline
SPEED
bob
INCUNE
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
buttons. Each time you
press the incline increase or decrease button, the
incline will change by 0.5%. If you press one of the
numbered incline buttons, the treadmill will adjust
to the selected incline setting. Note: After you
press the buttons, it may take a moment for the
treadmill to reach the selected incline setting.
.
6.
Before using the
handgrip pulse
sensor, first remove the sheets
Monitor your progress with the matrix and the
displays.
The matrix--When
the
manual mode is selected, the display will
show a track that represents 1/4 mile (400 meters). As you exercise,
the indicators around the
m
of clear plastic
from the metal
contacts. In addition, make sure
that your hands
are clean.
B
To use the handgrip pulse sensor, stand on the
foot rails and hold the metal contacts. Avoid mov-
mm
ing your hands. When your pulse is detected, your
heart rate will be shown. For the most accurate
heart rate reading, continue to hold the contacts
for about 15 seconds.
again begin to light in succession.
lected, this display will
show the elapsed time.
When a workout is se-
.
IB..2
c:
LI
TIME
lected, the display will
show the time remaining in the workout rather than
the elapsed time.
Distance/Incline
dis-
play--This display
shows the distance that
[3.21
Calories/Pu Ise
LI.
When you are finished
key from the console.
exercising,
remove the
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the "off" position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill's electrical components may wear prematurely.
you have walked or run.
DISTANCE
This display will also
show the incline setting
for several seconds, each time the incline changes.
display--This
display
shows the approximate
number of calories you
have burned. The dis-
Contacts
mmm_
track will light in succession until the entire track is
lit. The track will then darken and the indicators will
Time display--When
the manual mode is se-
Measure your heart rate if desired.
I
CALORIES
play will also show your
heart rate when you use the handgrip pulse sensor.
17
HOW TO USE A PRESET WORKOUT
1.
segment, a series of
tones will sound and the
Current Segment
next segment of the profile will begin to flash. If a
different speed or incline
setting is programmed for
the next segment, the
speed or incline setting
will flash in the display to alert you.
Insert the key into the console.
__=
See HOW TO TURN ON THE POWER on page 16.
2.
Select
a preset
workout.
To select a preset workout, press the Weight Loss
Workouts, Aerobic Workouts, Endurance
Workouts, or Performance Workouts button repeatedly.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
When a preset workout
is selected, the workout
time will appear in the
Time display, the minimum speed setting of
the workout will appear
in the Distance/Incline display, the maximum speed
setting will appear in the Calories/Pulse display,
and the name of the workout will appear in the
Speed display. In addition, a profile of the speed
settings of the workout will scroll across the matrix.
3.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or incline
buttons; however, when the next segment of the
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Go button.
The walking belt will begin to move at 1 mph. When
the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline
settings for the next segment.
Press the Go button to start the workout.
A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings of the workout. Hold the handrails
and begin walking.
.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are programmed for each segment. Note: The same
speed setting and/or incline setting may be programmed for consecutive segments.
Monitor your progress
displays.
with the matrix and the
See step 5 on page 17.
5.
Measure your heart rate if desired.
See step 6 on page 17.
During the workout, the profile will show your
progress. The flashing segment of the profile represents the current segment of the workout. The
height of the flashing segment indicates the speed
setting for the current segment. At the end of each
.
When you are finished
key from the console.
See step 7 on page 17.
18
exercising, remove the
THE iNFORMATiON MODE
HOW TO USE THE STEREO SOUND SYSTEM
The console features an information mode that keeps
track of the total number of hours that the treadmill has
To play music or audio books through the console's
stereo speakers, you must connect your MP3 player,
CD player, or other personal audio player to the console through the audio jack.
been used and the total distance that the walking belt
has moved. The information mode also allows you to
switch the console from miles to kilometers and to turn
on and turn off the display demo mode.
To use the audio jack, locate the audio cable and plug
it into the audio jack near the speakers. Then, plug the
audio cable into a jack on your MP3 player, CD player,
or other personal audio player. Make sure that the
audio cable is fully plugged in.
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
Next, press the Play button on your MP3 player, CD
player, or other personal audio player.
The Time display will show
the total number of hours the
treadmill has been used.
The Distance/Incline display
will show the total number of
miles (or kilometers) that the
walking belt has moved.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat surface instead of on the console.
IJ
[2c!
LI
An "E" for English miles or
an "M" for metric kilometers
will appear in the
Calories/Pulse display.
Press the Speed increase
button to change the unit of
measurement if desired.
The console features a display demo mode, designed
to be used if the treadmill is
displayed in a store. While
the demo mode is turned on,
the console will function nor-
d
mally when you plug in the power cord, switch the
reset/off circuit breaker to the reset position, and insert
the key into the console. However, when you remove
the key, the displays will remain lit, although the buttons will not function. If the demo mode is turned on, a
"d" will appear in the Speed display while the information mode is selected. To turn on or turn off the demo
mode, press the Speed decrease button.
To exit the information mode, remove the key from the
console.
19
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position, if you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
Ibs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in
the storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85 ° F (30 ° C).
Latch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
knob is locked in the storage position.
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
20
Wheel
Base
HOW TO LOWER THE TREADMILL
FOR USE
1. Hold the upper end of the treadmill with your right hand.
Pull the latch knob to the left and hold it. It may be necessary to push the frame forward as you pull the knob to
the left. Pivot the frame downward and release the latch
knob.
Latch Knob
2. Hold the metal frame firmly with both hands and lower
it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your
legs and keep your back straight.
/
21
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed, if further assistance is needed, see the back cover of this manual.
PROBLEM:
The power does not turn on
SOLUTION:
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppressor that meets all of the specifications described on page 14. iMPORTANT: The treadmill is not
compatible with GFCl-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
C.
Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
c
Tripped
Position
Position
Reset
PROBLEM:
The power turns off during
use
SOLUTION:
a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the back cover of this manual.
PROBLEM:
The console displays
remain lit when you remove the key from the console
SOLUTION:
a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 19 to turn off the demo mode.
PROBLEM:
The displays
SOLUTION:
a. Remove the key from the console and UNPLUG
THE POWER CORD. With the help of a second
person, carefully tip down the Uprights (75, 80).
There may be three #8 x 2" Screws (16) in the bottom of the Belly Pan (73). If there are, remove them.
Note: A Phillips screwdriver with a shaft at least 5
in. (13 cm) long is required. Then, raise the
Uprights.
of the console do not function
properly
75
i
16
22
Remove the three #8 x 3/4" Screws (1) and carefully pivot the Motor Hood (60) off.
1
6O
Locate the Reed Switch (71) and the Magnet (45)
on the left side of the Pulley (46). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 ram). if necessary, loosen the 3/4" Screw (17), move the Reed
Switch slightly, and then retighten the Screw.
Reattach the Motor Hood (not shown) with the #8 x
3/4" Screws and the #8 x 2" Screws if necessary.
Run the treadmill for a few minutes to check for a
1/8 in.
17
45
Top
View
correct speed reading.
PROBLEM:
The incline of the treadmill
SOLUTION:
a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM:
The walking
SOLUTION:
a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 14.
b.
does not change correctly
belt slows when walked on
If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
Rear Roller Bolts
c. If the walking belt still slows when walked on, see the back cover of this manual.
23
PROBLEM:
The walking
belt is off-center or slips when walked on
SOLUTION:
a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
b.
If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in, (5 to 7 cm) off
the walking platform. Be careful to keep the walking belt centered, Then, plug in the power cord, insert the key, and carefully walk on the treadmill for
a few minutes, Repeat until the walking belt is
properly tightened.
24
EXERCISE GUiDELiNES
w nri,,,l
Burning Fat--To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy, if your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
: Before
boginn this
ng
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
Aerobic Exercise--if your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
Warming Up--Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
fat burning and aerobic exercise.
Training Zone Exercise--Exercise
for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise-never hold your breath.
i65
155
145
140
130
125
115
_
145
138
130
125
118
110
103
_)
125
120
115
110
]05
95
90
W
20
30
40
50
60
70
80
Cooling Down--Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERClSE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your "training zone." The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
PART LISTmModel
No. 831.24855.1
R0908A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
17
10
1
4
2
6
#8 x 3/4" Screw
#8 x 1/2" Screw
#8 x 1/2" Ground Screw
#8 x 1" Tek Screw
#10 x 3/4" Screw
5/16" x 1" Bolt
51
52
53
54
55
56
1
1
1
1
1
2
Frame
Left Rear Foot
Idler Roller Ground Wire
Right Rear Foot
Idler Roller
Idler Roller Bracket
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
3
1
4
2
3
4
4
2
5
3
9
2
2
2
2
1
1
2
7
8
2
4
2
2
4
4
3
6
2
3/8" x 2" Bolt
3/8" x 1 3/4" Bolt
3/8" x 4" Bolt
1/4" x 3/4" Bolt
3/8" Nut
3/8" Star Washer
5/16" Star Washer
1/4" Star Washer
#8 x 3/4" Tek Screw
#8 x 2" Screw
3/4" Screw
5/16" x 1 1/2" Bolt
5/16" x 3 5/8" Bolt
3/8" x 1 1/4" Bolt
Idler Roller Bolt
3/8" x 1 3/4" Bolt
3/8" Incline Motor Bolt
3/8" x 3/4" Bolt
#8 x 1 1/2" Bright Screw
#12 x 1 1/4" Screw
Motor Bolt
Belt Guide Screw
1/4" Washer
1/4" Split Washer
3/8" Jam Nut
5/16" Flange Nut
Hood Clip
#3 x 1/4" Screw
Foot Rail Decal
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
2
4
2
5/32" Hex Key
Hex Key
Hood Accent
Motor Hood
Lift Frame
Lift Frame Ground Wire
Wire Tie
Drive Belt
Drive Motor
Controller Ground Wire
Power Cord
Power Cord Grommet
Reset/Off Circuit Breaker
Controller
Reed Switch
Reed Switch Clamp
Belly Pan
Left Handrail Spacer
Left Upright
Incline Motor
Incline Motor Spacer
Right Handrail Spacer
Upright Wire
Right Upright
Bolt Spacer
Right Upright Spacer
Base Cap
Base Foot
Caution Decal
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
1
2
1
1
2
2
2
3
1
1
1
1
1
1
Left Foot Rail
Warning Decal
Platform Cushion
Walking Platform
Walking Belt
Belt Guide
Frame Cap
Frame Spacer
Drive Roller Spacer
Magnet
Drive Roller/Pulley
Latch Cap
Storage Latch
Latch Knob
Right Foot Rail
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
2
2
2
2
5
1
1
1
1
3
1
4
2
Left Upright Spacer
Base
Wheel
Base Foot Spacer
15 1/2" Wire Tie
Releaseable Tie
8" Tie
Key Clip
Left Tray
Audio Cable
Console
Wire Tie
Console Back
Pulse Plate
Upper Handrail Cap
26
Key No. Qty.
101
102
103
104
105
106
107
1
6
1
1
2
1
1
Description
Key No. Qty.
Key Plate
Console Clamp
Right Tray
Right Handrail
Handrail Cap
Crossbar
Left Handrail
108
*
*
*
*
*
2
-
Description
#8 x 1 1/2" Screw
8" Blue Wire, M/F
10" Blue Wire, 2F
12" Red Wire, M/F
10" Black Wire, M/F
User's Manual
Note: Specifications are subject to change without notice, See the back cover of this manual for information about
ordering replacement parts. If a part is missing, call 1-888-533-1333. *These parts are not illustrated.
27
m
26-4
X
35
r"'
0
m
36
46
m
Z
0
37
40
39
I
\
108
0
oo
56.
30
m
55
Z
0
19
!
29
47
21
51
35
5O
49
57
8
4_
O_
t_
t_
!
58
11
48
(:D
r,,.o
(:D
OO
>
EXPLODED
DRAWING BmModel
No. 831.24855.1
6o
59
27
61
20
4
64
25
65
71
15
29
ROgOSA
EXPLODED
74
DRAWING C--Model
No. 831.24855.1
RogosA
i3
77
86
12
81
85
87
12
9
85
_89
11
_84
88
9
71
81
88
--
92
30
EXPLODED
DRAWING DmModel
No. 831.24855.1
RogosA
94
3
4_
103
34
34
99
102
107
1
10
106
2
104
105
105
31
Your Home
For repair--in
or heating
your home--of
all major brand appliances, lawn and garden equipment,
and cooling systems, no matter who made it, no matter who sold it!
iiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiii
For the replacement
parts, accessories,
and user's manuals that you need to do-it-yourself.
iiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiii
For Sears professional
installation
of home appliances
and items like garage door openers
and water heaters.
iiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiii
1-800-4-MY-HOME
® (1-800-469-4663)
call
anyt,me,
day
orn,0ht/U.S.A,
and
Canada/
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics,
call or go on-line for the location of your nearest
Sears
Parts & Repair
1-800-488-1222
Center.
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement
or maintenance
agreement
1-800-827-6655
(Canada)on
(U.S.A.)
(U.S.A.)
a product serviced by Sears:
1-800-361-6665
(Canada)
Pard pedir servicio de reparacion a domicilio, y pard ordenar piezas:
1-888-SU-HOGAR
®(1-888-784-6427)
....
® Registered Trademark / TMTrademark / SMService Mark of Sears Brands, LLC
® Marca Registrada / TMMarca de F#,brica / SMMarca de Servicio de Sears Brands, LLC
f
90 DAY FULL WARRANTY
If this Sears Treadmill Exerciser fails due to a defect in material or workmanship within 90 days of the
date of purchase, call 1-800-4-MY-HOME ®(1-800-469-4663) to arrange for free repair (or replacement if
repair proves impossible). The incline motor is warranted for 90 days from the date of purchase; the
drive motor is warranted for 25 years from the date of purchase.
This warranty does not apply when the Treadmill Exerciser is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
Sears, Roebuck
and Co., Hoffman Estates, IL 60179
J
Part No. 271187 R0908A
Printed in USA © 2008 ICON IP, Inc.
Download PDF
Similar pages