Operating Instructions Compact Stereo System

SC-HC397EB&EG&395EG~RQT0A88-B.book 1 ページ
2015年11月30日 月曜日 午後1時43分
Operating Instructions
Compact Stereo System
Model No. SC-HC397
SC-HC395
Thank you for purchasing this product.
Please read these instructions carefully before using this product,
and save this manual for future use.
Included Installation Instructions (l 2, 19 and 20)
The installation work should be done by a qualified installation specialist.
Before commencing work, carefully read these installation instructions and the operating
instructions to ensure that installation is performed correctly.
(Please keep these instructions. You may need them when maintaining or moving this unit.)
Model number suffix “EB” denotes UK model.
EB EG
RQT0A88-B
until
2016/02/22
SC-HC397EB&EG&395EG~RQT0A88-B.book 2 ページ
2015年11月30日 月曜日 午後1時43分
Caution for AC Mains Lead
Safety precautions
(For the AC mains plug of three pins)
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure
that the replacement fuse has a rating of 5-ampere and
that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark Ï or the BSI mark Ì on the
body of the fuse.
If the plug contains a removable fuse cover you must
ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from your
local dealer.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of
AC mains plug (figures A and B). Confirm the AC
mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
Figure A
≥ To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or
splashing.
– Do not place objects filled with liquids, such as vases, on
this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
– Do not let metal objects fall inside this unit.
– Do not place heavy items on this unit.
AC mains lead
≥ To reduce the risk of fire, electric shock or product damage,
– Ensure that the power supply voltage corresponds to the
voltage printed on this unit.
– Insert the mains plug fully into the socket outlet.
– Do not pull, bend, or place heavy items on the lead.
– Do not handle the plug with wet hands.
– Hold onto the mains plug body when disconnecting the
plug.
– Do not use a damaged mains plug or socket outlet.
≥ The mains plug is the disconnecting device.
Install this unit so that the mains plug can be unplugged from
the socket outlet immediately.
CAUTION
2. Replace the fuse and close or attach the fuse
cover.
Figure A
Figure B
Fuse
(5 ampere)
RQT0A88
Unit
Figure B
Fuse cover
2
WARNING
Fuse
(5 ampere)
Unit
≥ This unit utilizes a laser. Use of controls or adjustments or
performance of procedures other than those specified herein
may result in hazardous radiation exposure.
≥ Do not place sources of naked flames, such as lighted
candles, on this unit.
≥ This unit may receive radio interference caused by mobile
telephones during use. If such interference occurs, please
increase separation between this unit and the mobile
telephone.
≥ This unit is intended for use in moderate climates.
Placement
≥ Place this unit on an even surface.
≥ To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in
cabinet or in another confined space. Ensure this unit is
well ventilated.
– Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
– Do not expose this unit to direct sunlight, high
temperatures, high humidity, and excessive vibration.
SC-HC397EB&EG&395EG~RQT0A88-B.book 3 ページ
2015年11月30日 月曜日 午後1時43分
Battery
≥ Danger of explosion if battery is incorrectly replaced.
Replace only with the type recommended by the
manufacturer.
≥ Mishandling of batteries can cause electrolyte leakage and
may cause a fire.
– Remove the battery if you do not intend to use the remote
control for a long period of time. Store in a cool, dark
place.
– Do not heat or expose to flame.
– Do not leave the battery(ies) in a car exposed to direct
sunlight for a long period of time with doors and windows
closed.
– Do not take apart or short circuit.
– Do not recharge alkaline or manganese batteries.
– Do not use batteries if the covering has been peeled off.
≥ When disposing of the batteries, please contact your local
authorities or dealer and ask for the correct method of
disposal.
Accessories
Check the supplied accessories before using this unit.
∏ 1 Remote control
(N2QAYB000944)
∏ 1 Battery for remote control
∏ (For the United Kingdom and Ireland)
1 AC mains lead
(K2CT2YY00097)
∏ (For others)
1 AC mains lead
(K2CQ2YY00119)
∏ [SC-HC397]
1 DAB indoor antenna
Product Identification Marking is located on the bottom of the
unit.
Table of contents
Caution for AC Mains Lead .............................. 2
Safety precautions............................................ 2
Accessories....................................................... 3
Control reference guide ................................... 4
Connections ...................................................... 5
Inserting media ................................................. 6
Bluetooth® operations ...................................... 7
Media playback controls .................................. 9
[SC-HC397] Listening to DAB/DAB+ ................ 10
Listening to FM radio ..................................... 12
Sound adjustment .......................................... 13
Clock and Timer .............................................. 13
Others .............................................................. 14
Troubleshooting.............................................. 15
Unit and media care........................................ 17
About Bluetooth® ............................................ 18
Playable media................................................ 18
Licenses .......................................................... 18
Attaching the unit to a wall (optional)........... 19
Specifications.................................................. 21
(RFA3669)
∏ [SC-HC395]
1 FM indoor antenna
(RSAX0002)
Wall mounting accessories
∏ 1 Safety holder
(RSC1266)
∏ 2 Wall mount
brackets
(RSC1262-1)
∏ 1 Screw
(XTB3+8JFJK-J)

≥ Do not use AC mains lead with other equipment.
≥ Product numbers provided in these operating instructions are
correct as of November 2015. These may be subject to
change.
About descriptions in these operating
instructions
≥ Pages to be referred to are indicated as “l ±±”.
≥ Unless otherwise indicated, operations are described using
the remote control.
≥ These operating instructions are applicable to models
SC-HC397 and SC-HC395. Unless otherwise indicated,
illustrations in these operating instructions are of
SC-HC397.
[SC-HC397] :indicates features applicable to SC-HC397
only.
[SC-HC395] :indicates features applicable to SC-HC395
only.
3
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 4 ページ
2015年11月30日 月曜日 午後1時43分
Control reference guide
Top view
1
2
Standby/on switch (Í/I) (Í)
Press to switch the unit from on to standby mode or vice
versa.
In standby mode, the unit is still consuming a small
amount of power.
Select the audio source
On this unit:
“CD” ----------. “BLUETOOTH” ----------. “USB”
:
;
“AUX” ("-"-"-" “FM” ("-"-"-" (“DAB+”)*
On the remote control:
[ ]: “BLUETOOTH”
[USB/CD]: “CD” ,. “USB”
3
4
5
6
7
8
9
10
11
12
13
14
15
16
[RADIO/AUX]: (“DAB+”)* --------------------. “FM”
^-----"" “AUX”("--"-}
Basic playback control buttons
Adjust the volume (0 (min) to 50 (max))
Open or close the sliding door
Bluetooth®-pairing button
≥ Press to select “BLUETOOTH” as the audio source.
≥ Press and hold to enter pairing mode (l 7) or
disconnect a Bluetooth® device (l 8).
NFC touch area (l 7)
Port for USB devices / DC OUT terminal (l 6)
AUX IN jack (l 5)
Remote control signal sensor
Distance: Within approx. 7 m directly in front
Angle: Approx. 30o left and right
Display
Sliding door
Enter setup menu
Change the displayed information
Enter sound menu
Dim the display panel
Press again to cancel.
17 Mute the sound
Press again to cancel. “MUTE” is also cancelled when the
volume is adjusted or the unit is turned off.
18 Enter playback menu
19 Selection/OK
*
Only available for [SC-HC397]
∫ Using the remote control
Insert the battery so the terminals (i and j) match those
in the remote control.
Point it at the remote control signal sensor on this unit.
≥ To avoid interference, please do not put any objects in front of
signal sensor.
4
RQT0A88
(Alkaline or manganese
battery)
SC-HC397EB&EG&395EG~RQT0A88-B.book 5 ページ
2015年11月30日 月曜日 午後1時43分
Connections
Connect the antenna.
1
[SC-HC397]
This unit can receive DAB/DAB+ and FM stations with the DAB
antenna.
Adhesive tape (not supplied)
ュモャチモワヵバ
ョヮチモワヵ
ヘブ„
Be sure to tighten the nut
fully.
[SC-HC395]
DAB indoor antenna
(supplied)
ュモャチモワヵバ
ョヮチモワヵ
ヘブ„
Adhesive tape
(not supplied)
FM indoor antenna
(supplied)
Connect the AC mains lead after all other connections are completed.
2
This unit consumes a small amount of AC power (l 21) even when turned off.
≥ In the interest of energy conservation, if you will not be using this unit for an extended period
of time, unplug it from the mains socket.
To a mains socket
AC mains lead (supplied)

≥
≥
≥
≥
These speakers do not have magnetic shielding. Do not place them near a TV, personal computer or other magnetic devices.
Tape the antenna to a wall or column in a position with the least amount of interference.
[SC-HC397] If radio reception is poor, use a DAB outdoor antenna (not supplied).
[SC-HC395] If radio reception is poor, use a FM outdoor antenna with a right angle type connector (not supplied).
Connect an external music device
1
2
Connect an external music device using an audio
cable (not supplied).
≥ Plug type: ‰3.5 mm stereo
Press [RADIO/AUX] repeatedly to select “AUX”
and start playback on the connected device.
Audio cable
(not supplied)
∫ To select the sound input level of the
external device
1
2
While in AUX mode, press [SOUND] repeatedly to
select “INPUT LEVEL”.
Press [3, 4] to select “NORMAL” or “HIGH” and
then press [OK].
≥ The factory default is “NORMAL”.

≥ To improve sound distortion when “HIGH” is selected, select “NORMAL”.
≥ Switch the equalizer off or turn the volume of the external device down to reduce the input signal. High level of input signal will
distort the sound.
≥ For details, refer to the operating instructions of the device.
5
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 6 ページ
2015年11月30日 月曜日 午後1時43分
Inserting media
∫ Connecting a USB device
≥ Insert the USB device directly. Do not use any USB extension cable.
≥ Please disconnect the USB device if you finish using.
≥ Before removing the USB device, select a source other than “USB”.
∫ Inserting a CD
The label side
≥ Make sure to tilt the disc so as not to touch the sliding
door.
≥ Do not open the sliding door manually.
∫ Charging a device
Charging starts when a device (rated value: 5 V/1.5 A) is connected to the DC OUT terminal of this unit.
1
2
Turn the unit on.
Connect a device.
{. Confirm from the screen of the connected device, etc. to
make sure charging has started.
To the compatible device
USB cable
(not supplied)
≥ A cable compatible with your device is required. Use the
cable that comes with your device.
≥ Even if you connect a cable compatible with the DC OUT
terminal of this unit, your device may not be charged. In that
case, use the charger that comes with the device.
≥ Depending on your device, using other chargers may not
work. Check the operating instructions of your device before
use.
≥ Do not connect a device with a rated value higher than 5 V/
1.5 A to this unit.
≥ To check if charging is complete, look at the screen of the
connected device, etc.
≥ Once fully charged, remove the USB cable from the DC OUT
terminal.
≥ To continue charging during standby mode, make sure the
device has started charging before turning the unit to standby
mode.
– When charging a depleted device, do not turn the unit to
standby mode until the device becomes operational.

≥ Make sure that the unit does not fall when inserting or removing media.
≥ When moving this unit, be sure to remove all media and turn this unit to standby mode.
6
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 7 ページ
2015年11月30日 月曜日 午後1時43分
Bluetooth® operations
You can listen to the sound from the Bluetooth® audio device from this unit wirelessly.
≥ Refer to the operating instructions of the Bluetooth® device for details.
≥ If you intend to use an NFC (Near Field Communication)-compatible Bluetooth® device, proceed to “One-Touch
Connection (Connecting by NFC)”.
One-Touch Connection
(Connecting by NFC)
Connecting via Bluetooth® menu
Preparation
≥ Turn on the Bluetooth® feature of the device and
place the device near this unit.
∫ Pairing with Bluetooth® devices
1
Press [
] to select “BLUETOOTH”.
{. If “PAIRING” is indicated on the display, go to step 4.
To enter pairing mode*
2
3
Press [PLAY MENU] to select “PAIRING”.
Press [3, 4] to select “OK? YES” and then press
[OK].
For NFC-compatible Bluetooth® devices (AndroidTM
devices) only
Simply by touching an NFC (Near Field
Communication)-compatible Bluetooth® device on the
unit, you can complete all preparations, from
registering a Bluetooth® device to establishing a
connection.
Preparation
≥ Turn on the NFC feature of the device.
≥ Android device version lower than 4.1 requires the
installation of the app “Panasonic Music Streaming”
(free of charge).
1 Enter “Panasonic Music Streaming” in the search box
of Google PlayTM to search, and then select
“Panasonic Music Streaming”.
2 Start the app “Panasonic Music Streaming” on the
device.
– Follow on-screen instructions on your device.
– Always use the latest version of the app.
To pair with a device
4
Select “SC-HC397” or “SC-HC395” from the
Bluetooth® device’s Bluetooth® menu.
{. The MAC address (e.g., 6C:5A:B5:B3:1D:0F) may be
displayed before “SC-HC397” or “SC-HC395” is
displayed.
{. The name of the connected device is indicated on the
display for a few seconds.
5
*
Start playback on the Bluetooth® device.
1
2
You can also enter pairing mode by pressing and holding
[
-PAIRING] on the unit.
∫ Connecting a paired Bluetooth® device
1
2
3
Press [
] to select “BLUETOOTH”.
{. “READY” is indicated on the display.
Select “SC-HC397” or “SC-HC395” from the
Bluetooth® device’s Bluetooth® menu.
{. The name of the connected device is indicated on the
display for a few seconds.
Start playback on the Bluetooth® device.
3
Press [
] to select “BLUETOOTH”.
Touch and hold your device on the NFC touch area
of this unit [ ]. (l 4)
Do not move the Bluetooth® device until it beeps, displays
a message or reacts in some way.
Once the Bluetooth® device has reacted, move the device
away from this unit.
≥ When the registration and connection of the Bluetooth®
device is complete, the name of the connected device is
indicated on the display for a few seconds.
≥ The location of the NFC touch area differs depending on
the device. When a connection cannot be established
even if your Bluetooth® device has touched the NFC touch
area of this unit, change the position of the device. The
condition may also improve if you download the dedicated
app “Panasonic Music Streaming” and start it up.
Start playback on the Bluetooth® device.


≥ If prompted for the passkey, input “0000”.
≥ You can register up to 8 devices with this unit. If a 9th device
is paired, the device that has not been used the longest will
be replaced.
≥ This unit can only be connected to one device at a time.
≥ When “BLUETOOTH” is selected as the source, this unit will
automatically try and connect to the last connected
Bluetooth® device. (“LINKING” is indicated on the display
during this process.) If the connection attempt fails, try to
establish a connection again.
≥ If you touch another device to this unit, you can update the
Bluetooth® connection. The previously connected device will
be disconnected automatically.
≥ When the connection is established, playback may start
automatically depending on the type of device being used.
≥ The One-Touch Connection may not work properly
depending on the type of device being used.
7
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 8 ページ
2015年11月30日 月曜日 午後1時43分
Bluetooth® transmission mode
Disconnecting a Bluetooth® device
You can change the transmission mode to prioritise
transmission quality or sound quality.
1
Preparation
≥ Press [ ] to select “BLUETOOTH”.
≥ If a Bluetooth® device is already connected,
disconnect it.
2
1

2
Press [PLAY MENU] repeatedly to select
“LINK MODE”.
Press [3, 4] to select the mode and then press
[OK].
MODE 1: Emphasis on connectivity
MODE 2: Emphasis on sound quality

≥ Select “MODE 1” if the sound is interrupted.
≥ The factory default is “MODE 2”.
Bluetooth® input level
If the sound input level from the Bluetooth® device is
too low, change the input level setting.
Preparation
≥ Connect a Bluetooth® device.
1
2
Press [PLAY MENU] repeatedly to select “INPUT
LEVEL”.
Press [3, 4] to select the level and then press
[OK].
“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”
^---------------------------------------------------------J

≥ Select “LEVEL 0” if the sound is distorted.
≥ The factory default is “LEVEL 0”.
8
RQT0A88
While a Bluetooth® device is connected:
Press [PLAY MENU] repeatedly to select
“DISCONNECT?”.
Press [3, 4] to select “OK? YES” and then press
[OK].
≥ You can also disconnect the Bluetooth® device by pressing
and holding [ -PAIRING] on the unit.
≥ The Bluetooth® device will be disconnected if a different
audio source (e.g., “CD”) is selected.
SC-HC397EB&EG&395EG~RQT0A88-B.book 9 ページ
2015年11月30日 月曜日 午後1時43分
Media playback controls
The following marks indicate the availability of the
feature.
CD audio in CD-DA format and a CD that
contains MP3 files (l 18)
[USB]:
USB devices containing MP3 files (l 18)
[Bluetooth]: Connected Bluetooth® device
[CD]:
Preparation
≥ Turn the unit on.
≥ Insert the media or connect the Bluetooth® device.
≥ Press [USB/CD] or [ ] to select the audio source.
Basic controls
([CD], [USB], [Bluetooth])
Play
Press [1/;].
Stop
Press [∫].
≥ [USB]: The position is memorised and
“RESUME” is displayed.
≥ [USB]: Press [∫] twice to stop the
playback fully.
Pause
Press [1/;].
Press again to restart play.
Skip
Press [:/6] or [5/9] to skip
track.
Search
Playback modes ([CD], [USB])
Select the playback mode.
1
2
Press [PLAY MENU] to select “PLAYMODE” or
“REPEAT”.
Press [3, 4] to select the setting and then press
[OK].
PLAYMODE
OFF
PLAYMODE
Cancels the play mode setting.
1-TRACK
Only plays the selected track.
≥ “1”, “ ” is displayed.
(Skip to the desired track.)
1-ALBUM
Only plays the selected MP3 album.
RANDOM
Plays the contents randomly.
≥ “1”, “
” is displayed.
≥ “RND” is displayed.
1-ALBUM
RANDOM
Plays the tracks in the selected
MP3 album randomly.
≥ Press [3] or [4] to select the MP3
album.
≥ “1”, “ ”, “RND” is displayed.
REPEAT
[CD], [USB] Press [3] or [4] to skip the
MP3 album.
ON REPEAT
Turns on repeat mode.
During play or pause, press and hold
[:/6] or [5/9].
OFF
REPEAT
Turns off repeat mode.
∫ To display information
Press [DISPLAY] repeatedly.

≥ “`” is displayed.

≥ During random play, you cannot skip to the previous track.
≥ The mode is cancelled when you open the sliding door or
remove the USB device.
≥ To use this unit’s remote control with a Bluetooth® device, the
Bluetooth® device must support AVRCP (Audio Video
Remote Control Profile).
Depending on the status of the device, some controls may
not work.
≥ Maximum number of displayable characters:
[CD], [USB]: Approx. 32
[Bluetooth]: Approx. 16
≥ This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data
that is not supported will not be displayed or will be shown
differently.
≥ [Bluetooth]: When enjoying video contents with this function,
the video and audio output may not be synchronised. In this
case, select “MODE 1” in “LINK MODE” setting (l 8,
“Bluetooth® transmission mode”).
≥ Album and track indication for MP3 files.
“A _ _ _”: MP3 album number.
“T _ _ _”: MP3 track number.
≥ “ _ ” stands for the album or track number.
This indication is also used to refer to an album.
“ ”:
“ ”:
This indication is also used to refer to a track.
9
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 10 ページ
2015年11月30日 月曜日 午後1時43分
[SC-HC397]
Listening to DAB/DAB+
Preparation
≥ Make sure that the DAB antenna is connected. (l 5)
≥ Turn the unit on.
Memorising stations
To listen to DAB/DAB+ broadcasts, the available
stations need to be memorised in this unit.
≥ This unit will automatically start the “DAB AUTO
SCAN” and memorise the stations that are available
in your region if the memory is empty.
Press [RADIO/AUX] repeatedly to select “DAB+”.

≥ “SCAN FAILED” is displayed when the auto scan is
unsuccessful. Locate the position with the best reception
(l 11, “To verify or improve the signal reception quality”) and
then re-scan DAB/DAB+ stations.
∫ To re-scan DAB/DAB+ stations
When new stations are added or when the antenna
has been moved, reperform the auto scan.
1
2
Press [PLAY MENU] to select “AUTOSCAN” and
then press [OK].
While “START ?” is flashing,
Press [OK].

≥ When updating the memory with the auto scan, preset
stations will be erased. Preset them again (l right).
Listening to the memorised stations
Preparation*
1 Press [RADIO/AUX] repeatedly to select “DAB+”.
2 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
3 Press [3, 4] to select “STATION” and then press
[OK].
1
2
Press [RADIO/AUX] repeatedly to select “DAB+”.
Press [:/6] or [5/9] to select the
station.
Presetting DAB/DAB+ stations
You can preset up to 20 DAB/DAB+ stations.
Preparation
Press [RADIO/AUX] repeatedly to select “DAB+”.
1
2
While listening to a DAB/DAB+ broadcast
Press [OK].
Press [3, 4] to select the desired preset channel
number and then press [OK].

≥ You cannot preset stations when the station is not
broadcasting or when the secondary service is selected.
≥ The station occupying a channel is erased if another station
is preset in that channel.
∫ Listening to preset DAB/DAB+ stations
Preparation*
1 Press [RADIO/AUX] repeatedly to select “DAB+”.
2 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
3 Press [3, 4] to select “PRESET” and then press
[OK].
1
2
Press [RADIO/AUX] repeatedly to select “DAB+”.
Press [:/6] or [5/9] to select the
station.

≥ To select by preset, make sure that stations have already
been preset manually.
≥ To add additional preset stations, select the station using the
method mentioned in “Listening to the memorised stations”
(l left).
Listening to the secondary service
Some DAB/DAB+ stations provide a secondary service
as well as the primary service. If the station you are
listening to is providing secondary service, “ ” will be
displayed.
1
2
While “ ” is displayed.
Press [PLAY MENU] repeatedly to select “DAB
SECONDARY”.
Press [3, 4] to select the secondary service and
press [OK].

≥ The setting will go back to primary service when changes are
made (e.g. the station is changed).
*
10
RQT0A88
The “TUNEMODE” setting is memorised until it is changed.
SC-HC397EB&EG&395EG~RQT0A88-B.book 11 ページ
2015年11月30日 月曜日 午後1時43分

Display
Press [DISPLAY] to change the display.
The information will scroll through the display.
Each time you press the button:
Dynamic label:
Information about the
broadcast
PTY display:
Programme type
Ensemble label:
The name of the ensemble
Frequency display:
The frequency block and
frequency is displayed.
Time display:
Current time
≥ If broadcasting stations are memorised, proceed to
“To re-scan DAB/DAB+ stations” to memorise stations on
other frequency blocks. (l 10)
≥ If “SCAN FAILED” is still displayed, repeat steps 1 to 3 until a
station is memorised. If the situation does not improve, try
using an outdoor DAB antenna or consult your dealer.
∫ Checking the DAB/DAB+ signal
reception quality
1
While listening to the DAB/DAB+ broadcast:
Press [PLAY MENU] repeatedly to select “SIGNAL
QUALITY” and then press [OK].
≥ The current frequency block is displayed and
then the reception quality is indicated.
Reception quality
0 (poor) – 8 (excellent)
Automatic clock adjustment
If the DAB/DAB+ broadcast includes time information,
this unit’s clock will be automatically updated.
1
2
Press [PLAY MENU] repeatedly to select “AUTO
CLOCK ADJ”.
Press [3, 4] to select “ON ADJUST” and then
press [OK].

2
3
≥ Select “OFF ADJUST” to turn the automatic clock adjustment
function off.
To verify or improve the signal
reception quality
To check the signal reception quality, at least 1
frequency block needs to be successfully memorised.
≥ If “SCAN FAILED” is displayed after “DAB+” is
selected or after an auto scan, proceed to “Manually
tuning 1 frequency block” (l below)
4
If the signal reception quality is poor, move the
antenna to a position where the reception quality
improves.
To continue checking the quality of other frequency
blocks:
Press [3, 4] again and select the desired
frequency.
Press [OK] to exit.

≥ If the antenna has been adjusted, perform auto scanning and
update the station memory. (l 10)
≥ If stations have already been memorised to this unit,
proceed to “Checking the DAB/DAB+ signal
reception quality” (l right)
∫ Manually tuning 1 frequency block
Use this function to scan 1 frequency block after
adjusting the position of the DAB antenna.
Preparation
Note down a frequency block that can be received in
your region (e.g., 12B 225.648 MHz).
1
2
3
While “SCAN FAILED” is displayed.
Adjust the position of the DAB antenna.
Press [PLAY MENU] repeatedly to select
“MANUAL SCAN”.
Press [3, 4] to select the frequency block that is
receivable in your region and then press [OK].
11
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 12 ページ
2015年11月30日 月曜日 午後1時43分
Listening to FM radio
You can preset up to 30 channels.
Preparation
≥ Make sure that the antenna is connected. (l 5)
≥ Turn the unit on.
≥ Press [RADIO/AUX] repeatedly to select “FM”.
∫ Manual tuning and presetting
Select a radio broadcast.
1
2
3

≥ To start automatic tuning, press and hold [:/6] or
[5/9] until the frequency starts scrolling. Tuning
stops when a station is found.
≥ A station previously stored is overwritten when another
station is stored in the same channel preset.
Presetting stations automatically
1
2
Press [PLAY MENU] to select “A.PRESET”.
Press [3, 4] to select “LOWEST” or “CURRENT”
and then press [OK].
LOWEST:
To begin auto preset with the lowest frequency
(FM 87.50).
CURRENT:
To begin auto preset with the current frequency.*
{. The tuner starts to preset all the stations it can receive
into the channels in ascending order.
*
To change the frequency, refer to “Manual tuning and
presetting”.
Listening to a preset channel
1
2
3
Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
Press [3, 4] to select “PRESET” and then press
[OK].
Press [:/6] or [5/9] to select the
channel.
Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
Press [3, 4] to select “MANUAL” and then press
[OK].
Press [:/6] or [5/9] to tune to the
required station.
To preset the channel
4 While listening to the radio broadcast, press [OK].
5 Press [3, 4] to select the channel and then press
[OK].
∫ To improve FM sound quality
1
2
While receiving FM broadcasts, press
[PLAY MENU] repeatedly to select “FM MODE”.
Press [3, 4] to select “MONO” and then press
[OK].
≥ This setting can be preset and memorised. To do so,
continue to step 4 of “Manual tuning and presetting”.

≥ Select “STEREO” in step 2 to return to stereo broadcasts.
≥ “MONO” is cancelled if the frequency is changed.
∫ To display the current FM signal status
While receiving FM signal, press [DISPLAY].
≥ For Continental Europe:
While receiving FM signal, press [PLAY MENU]
repeatedly to display “FM STATUS” and then press
[OK].
“FM ST”:
“FM”:
The FM signal is tuned and in stereo.
There is no tuned signal or the FM signal
is in monaural.
“FM MONO”: “MONO” is selected in step 2 of “To
improve FM sound quality” (l above).
∫ To display RDS text data
(For Continental Europe only)
Press [DISPLAY] to display the text data.
≥ Each time you press the button:
“PS”:
“PTY”:
“FREQ”:
Programme service
Programme type
Frequency display

≥ “STEREO” is displayed when this unit tunes to a stereo
broadcast.
≥ The unit can display the text data transmitted by the radio
data system (RDS) available in some areas. (RDS displays
may not be available if reception is poor.)
12
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 13 ページ
2015年11月30日 月曜日 午後1時43分
Sound adjustment
Clock and Timer
The following sound effects can be added to the audio
output.
1
2
Press [SOUND] repeatedly to select the effect.
Press [3, 4] to select the setting and then press
[OK].
“MY SOUND”
(My sound)
“SOUND 1”, “SOUND 2” or
“SOUND 3”.
(l below, “Saving the sound
settings”)
“PRESET EQ”
(Preset Equalizer)
“HEAVY” (heavy), “SOFT” (soft),
“CLEAR” (clear), “VOCAL”
(vocal) or “FLAT” (flat/off).
≥ The factory default is “HEAVY”.
Setting the clock
This is a 24-hour clock.
1
2
“ON D.BASS” or “OFF D.BASS”.
“SURROUND”
(Surround)
“ON SURROUND” or
“OFF SURROUND”.
≥ The factory default is
“ON D.BASS”.
≥ The factory default is
“OFF SURROUND”.
≥ You may experience a reduction in sound quality when these
effects are used with some sources. If this occurs, turn the
sound effects off.
≥ When “AUX” is selected as the source, you can select
“INPUT LEVEL” to adjust the sound input level of the
external device. (l 5)
Saving the sound settings
You can save your desired sound settings to
“SOUND 1”, “SOUND 2” or “SOUND 3” as
“MY SOUND”.
1
2
3
≥ To display the clock, press [SETUP] repeatedly to select
“CLOCK” and then press [OK] once. The time is displayed for
10 seconds.
(During standby, press [DISPLAY] once.)
≥ The clock is reset when there is a power failure or when the
AC mains lead is removed.
≥ Reset the clock regularly to maintain accuracy.
You can set the timer so this unit turns on at a certain
time every day.
Preparation
Set the clock.
1
2
3
4
1
Press [3, 4] to select a setting number and then
press [OK].
4
Recalling the sound settings you have
saved
Press [SOUND] to select “MY SOUND”.
Press [3, 4] to select the desired sound setting
number and then press [OK].
Press [SETUP] repeatedly to select “TIMER ADJ”.
Press [3, 4] to set the starting time (“ON TIME”)
and then press [OK].
Press [3, 4] to set the finishing time
(“OFF TIME”) and then press [OK].
Press [3, 4] to select the music source* and then
press [OK].
Turning the timer on
Press [SETUP] to select “SAVE MY SOUND”.
≥ “SAVED” is displayed.
≥ The sound settings previously saved will be replaced
when you save new settings to the same setting
number.
1
2
Play timer
2
3
Adjust your desired sound effects. (l above)
Press [3, 4] to set the time and then press [OK].

“BASS” (Bass) or Adjust the level (j4 to i4).
“TREBLE” (Treble)
“D.BASS”
(Dynamic Bass)
Press [SETUP] repeatedly to select “CLOCK”.
Prepare the selected music source and set the
desired volume.
Press [SETUP] repeatedly to select “TIMER SET”.
Press [3, 4] to select “SET” and then press [OK].
≥ “F” is displayed.
≥ To turn the timer off, select “OFF”.
Press [Í] to turn the unit to standby mode.

≥ To display the timer settings, press [SETUP] repeatedly to
select “TIMER ADJ” and then press [OK] once.
The music source and volume will also be displayed if the
timer is turned on.
≥ During standby, if the timer is turned on, press [DISPLAY]
twice to display the settings.
≥ This unit can be used as normal after the timer is set,
however:
– Turn the unit to standby mode before the timer start time.
– Even if the audio source or the volume is changed, the
timer will still use the audio source and volume that was
set when the timer was turned on.
*
“CD”, “USB”, “DAB+” ([SC-HC397]), “FM” and “AUX” can be
set as the music source.
13
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 14 ページ
2015年11月30日 月曜日 午後1時43分
Sleep timer
Others
The sleep timer can turn the unit off after a set time.
1
2
Press [SETUP] repeatedly to select “SLEEP”.
Press [3, 4] to set the time (in minutes) and then
press [OK].
“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”
^------------------. “OFF” (Cancel) (------------------J

≥ The remaining time is indicated on the unit’s display except
when other operations are performed.
≥ The play timer and sleep timer can be used together. The
sleep timer is always the main timer on the unit.
Auto off function
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being
used for approximately 20 minutes.
To cancel this function
1
2
Press [SETUP] repeatedly to select “AUTO OFF”.
Press [3, 4] to select “OFF” and then press [OK].

≥ To turn the function on, select “ON” in step 2.
≥ This setting cannot be selected when “DAB+” ([SC-HC397]) or
“FM” is the source.
≥ When connected to a Bluetooth® device, the function does
not work.
Bluetooth® standby
When “SC-HC397” or “SC-HC395” is selected from a
paired Bluetooth® device’s Bluetooth® menu, this unit
will turn on automatically from standby mode and
establish a Bluetooth® connection.
1
2
Press [SETUP] repeatedly to select “BLUETOOTH
STANDBY”.
Press [3, 4] to select “ON” and then press [OK].

≥ To turn the function off, select “OFF” in step 2.
14
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 15 ページ
2015年11月30日 月曜日 午後1時43分
Changing the unit and remote
control code
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1
2
3
Press [USB/CD] to select “CD”.
While pressing and holding [SELECTOR] on the
unit, press and hold [USB/CD] on the remote
control until the unit’s display shows “REMOTE 2”.
Press and hold [OK] and [USB/CD] on the remote
control for at least 4 seconds.

≥ To change the mode back to “REMOTE 1”, press [USB/CD]
to select “CD” and then repeat the step 2 and 3 but replace
[USB/CD] with [ ].
Software update
Occasionally, Panasonic may release updated
software for this unit that may add or improve the way
a feature operates. These updates are available free of
charge.
For more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
∫ Checking the software version
The version of the installed software is displayed.
Press [SETUP] repeatedly to select “SW VER.” and
then press [OK].
≥ Press [OK] to exit.
Troubleshooting
Before requesting service, make the following checks. If
you are uncertain about some of the check points, or if the
solutions indicated in the following guide does not resolve
the issue, then consult your dealer for instructions.
To return all settings to the factory defaults
When the following situations occur, reset the memory:
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
1 Disconnect the AC mains lead. (Wait for at least
3 minutes before proceeding to step 2.)
2 While pressing and holding down [Í/I] on the
unit, reconnect the AC mains lead.
≥ Keep holding down [Í/I] until “---------” appears on the
display.
3 Release [Í/I].

≥ All the settings are returned to the factory defaults. You will
need to reset the memory items.
General
Cannot turn on the unit.
≥ After connecting the AC mains lead, wait about 10 seconds before
turning on the unit.
Humming heard during playback.
≥ If an AC mains lead or fluorescent lights are near the cords, then
keep other appliances and cords away from the cables.
The unit does not work.
≥ One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the unit to switch the unit to standby.
≥ If the unit does not switch to standby, press [Í/I] on the unit
for approximately 10 seconds. The unit is forcibly switched
to standby. Alternatively, disconnect the AC mains lead, wait
for at least 3 minutes, then reconnect it.
2 Press [Í/I] on the unit to switch it on. If the unit still cannot be
operated, consult the dealer.
MP3 cannot be read.
≥ You may not be able to play MP3 if you have copied a
multi-session disc that has no data between sessions.
≥ When creating a multi-session disc, it is necessary to close the
session.
≥ The amount of data on the disc is too small. Set the amount of
data to above 5 MB.
Charging does not start during standby mode.
≥ Turn the unit on. Check the charging has started, and then turn
the unit to standby mode. (l 6)
Noise is heard.
≥ When a device is connected to both the AUX IN jack and the DC
OUT terminal, noise may be generated depending on the device.
In this case, remove the USB cable from the DC OUT terminal.
15
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 16 ページ
2015年11月30日 月曜日 午後1時43分
Remote control
Bluetooth®
The remote control does not work properly.
Pairing cannot be completed.
≥ The battery is depleted or inserted incorrectly. (l 4)
≥ Check the Bluetooth® device condition.
Disc
Incorrect display or play does not start.
≥ Make sure that the disc is compatible with this unit. (l 18)
≥ There is moisture on the lens. Wait for about an hour and then try again.
USB
The device cannot be connected.
≥ The pairing of the device was unsuccessful or the registration has
been replaced. Try re-pairing the device. (l 7)
≥ This unit might be connected to a different device. Disconnect the
other device and try re-pairing the device. (l 7)
≥ If the problem persists, turn the unit off and on, then try again.
The device is connected, but audio cannot be
heard through this unit.
≥ Disconnect the USB device and then reconnect it. Alternatively,
turn the unit off and on again.
≥ For some built-in Bluetooth® devices, you have to set the audio
output to “SC-HC397” or “SC-HC395” manually. Read the
operating instructions for the device for details.
The USB drive or its contents cannot be read.
The sound is interrupted.
No response when [1/;] is pressed.
≥ Large file size or high memory USB flash drive takes longer time
to read.
≥ The device is out of the 10 m communication range. Place the
Bluetooth® device closer to this unit.
≥ Remove any interference between this unit and the device.
≥ Other devices that use the 2.4 GHz frequency band, such as
wireless routers, microwaves, cordless phones, etc. are
interfering. Place the Bluetooth® device closer to this unit and
distance it from the other devices.
≥ Select “MODE 1” for stable communication. (l 8)
The elapsed time displayed is different from the
actual play time.
The One-Touch Connection (NFC feature) is not
working.
≥ The USB drive format or its contents is/are not compatible with the
unit (l 18).
≥ The USB host function of this product may not work with some
USB devices.
Slow operation of the USB flash drive.
≥ Copy the data to another USB device or backup the data and
reformat the USB device.
Radio
[SC-HC397]
DAB/DAB+ reception is poor.
≥ Keep the antenna away from computers, televisions, other cables
and cords.
≥ Use an outdoor antenna (l 5).
Static or noisy reception is heard while listening to
a radio broadcast.
≥ Confirm the antenna is properly connected. (l 5)
≥ Adjust the position of the antenna.
≥ Try to keep a certain amount of distance between the antenna and
AC mains lead.
≥ Try using an outdoor antenna if there are buildings or mountains
nearby. (l 5)
≥ Turn the TV or other audio players off or separate it from this unit.
≥ Keep this unit away from mobile phones if there is interference.
≥ Make sure the unit and the NFC feature of the device are turned
on. (l 7)
Messages
The following messages or service numbers may
appear on the unit’s display.
“--:--”
≥ You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 13).
“ADJUST CLOCK”
≥ Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥ Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥ The unit has been left unused for about 20 minutes and will shut
down within a minute. Press any button to cancel it.
“ERROR”
≥ Incorrect operation is performed. Read the instructions and try
again.
“F” / “F” (“ ” stands for a number.)
≥ There is a problem with this unit.
Write down the displayed number, disconnect the AC mains lead
and consult your dealer.
“ILLEGAL OPEN”
≥ Sliding door is in the wrong position. Turn the unit off and on
again. If this display appears again, consult the dealer.
“NODEVICE”
≥ The USB device is not inserted correctly. Read the instructions
and try again (l 6).
16
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 17 ページ
2015年11月30日 月曜日 午後1時43分
“NO DISC”
≥ Insert the disc to be played (l 6).
[SC-HC397]
“NO MEMORY”
≥ There are no preset DAB/DAB+ stations to select. Preset some
channels. (l 10)
“NO PLAY”
≥ A CD that is not in CD-DA or MP3 format is inserted. It cannot be
played.
≥ Examine the content. You can only play supported format. (l 18)
≥ The files in the USB device can be corrupted. Format the USB
device and try again.
≥ The unit may have a problem. Turn the unit off and then on again.
[SC-HC397]
“NO SIGNAL”
≥ This station cannot be received. Check your antenna (l 5).
“PLAYERROR”
≥ You played an unsupported MP3 file. The system will skip that
track and play the next one.
“READING”
Unit and media care
Pull out the AC mains lead from the outlet before
maintenance.
∫ Clean this unit with a soft, dry cloth
≥ When dirt is heavy, wring a wet cloth tightly to wipe the dirt,
and then wipe it with a dry cloth.
≥ When cleaning the speaker covers, use a fine cloth.
Do not use tissues or other materials that can fall apart.
Small pieces may get stuck inside the speaker cover.
≥ Never use alcohol, paint thinner or benzine to clean this unit.
≥ Before using chemically treated cloth, carefully read the
cloth’s instructions.
∫ Maintenance of the lens
≥ Clean the lens regularly to prevent malfunctions. Use a dust
blower to remove dust and a cotton swab if it is extremely
dirty.
≥ You cannot use a CD type lens cleaner.
≥ Do not leave the sliding door open for prolonged periods of
time. This will cause the lens to get dirty.
≥ Be careful not to touch the lens with your fingers.
≥ The unit is checking the CD/USB information. After this display
has disappeared, start operating.
Lens
“REMOTE ” (“  ” stands for a number.)
≥ The remote control and this unit are using different codes. Change
the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and [ ]
for at least 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and
[USB/CD] for at least 4 seconds.
∫ Clean discs
DO
DO NOT
[SC-HC397]
“SCAN FAILED”
≥ Stations are not receivable. Check your antenna and try Auto
scanning (l 10).
If “SCAN FAILED” is still displayed find the best signal reception
with the “MANUAL SCAN” tuning function. (l 11)
“SOUND NOT SET” (“ ” stands for a number.)
≥ There is no saved setting under the selected sound setting
number. Save the sound settings. (l 13)
“USB OVER CURRENT ERROR”
≥ The USB device is drawing too much power. Select a source other
than “USB”, remove the USB and turn the unit off.
“VBR”
≥ The system cannot show the remaining play time for variable bit
rate (VBR) tracks.
Wipe with a damp cloth and then wipe dry.
∫ Disc handling precautions
≥ Handle discs by the edges to avoid inadvertent scratches or
fingerprints on the disc.
≥ Do not attach labels or stickers to discs.
≥ Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
≥ Do not use the following discs:
– Discs with exposed adhesive from removed stickers or
labels (rented discs etc.).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.
∫ To dispose or transfer this unit
The unit may keep the user settings information in the
unit. If you discard this unit either by disposal or
transfer, then follow the procedure to return all the
settings to the factory defaults to delete the user
settings.
(l 15, “To return all settings to the factory defaults”)
≥ The operation history may be recorded in the
memory of this unit.
17
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 18 ページ
2015年11月30日 月曜日 午後1時43分
About Bluetooth®
Panasonic bears no responsibility for data and/or
information that is compromised during a
wireless transmission.
Playable media
Compatible CD
≥ A disc with the CD Logo.
∫ Frequency band used
≥ This system uses the 2.4 GHz frequency band.
∫ Certification of this device
≥ This system conforms to frequency restrictions and
has received certification based on frequency laws.
Thus, a wireless permit is not necessary.
≥ The actions below are punishable by law in some
countries:
– Taking apart or modifying the system.
– Removing specification indications.
∫ Restrictions of use
≥ Wireless transmission and/or usage with all
Bluetooth® equipped devices is not guaranteed.
≥ All devices must conform to standards set by
Bluetooth SIG, Inc.
≥ Depending on the specifications and settings of a
device, it can fail to connect or some operations can
be different.
≥ This system supports Bluetooth® security features.
But depending on the operating environment and/or
settings, this security is possibly not sufficient.
Transmit data wirelessly to this system with caution.
≥ This system cannot transmit data to a Bluetooth®
device.
∫ Range of use
≥ Use this device at a maximum range of 10 m. The
range can decrease depending on the environment,
obstacles or interference.
∫ Interference from other devices
≥ This system may not function properly and troubles
such as noise and sound jumps may arise due to
radio wave interference if this system is located too
close to other Bluetooth® devices or the devices that
use the 2.4 GHz band.
≥ This system may not function properly if radio waves
from a nearby broadcasting station, etc. is too
strong.
∫ Intended usage
≥ This system is for normal, general use only.
≥ Do not use this system near an equipment or in an
environment that is sensitive to radio frequency
interference (example: airports, hospitals,
laboratories, etc).
18
RQT0A88
≥ This unit can play back discs that conform to the CD-DA
format.
≥ The unit may not be able to play some discs due to the
condition of the recording.
≥ Before playback, finalise the disc on the device it was
recorded on.
≥ This system can access up to: 99 tracks
Compatible USB devices
≥ This unit does not guarantee connection with all USB
devices.
≥ FAT12, FAT16 and FAT32 file systems are supported.
≥ This unit supports USB 2.0 full speed.
≥ USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
Compatible MP3 files
≥ Supported format: Files with the extension “.mp3” or “.MP3”.
≥ Depending on how you create the MP3 files, they may not
play in the order you numbered them or may not play at all.
CD-R/RW
≥ This system can access up to: 999 tracks and 255 albums
(including root folder)
≥ Disc formats: ISO9660 level 1 and level 2 (except for
extended formats).
≥ If the disc includes both MP3 and normal audio data
(CD-DA), the unit plays the type recorded in the inner part of
the disc.
≥ This unit cannot play files recorded using packet write.
USB device
≥ This system can access up to: 8000 tracks, 800 albums
(including root folder) and 999 tracks in one album
Licenses
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
Panasonic Corporation is under license.
Other trademarks and trade names are those of their respective
owners.
Google Play and Android are trademarks of Google Inc.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
SC-HC397EB&EG&395EG~RQT0A88-B.book 19 ページ
2015年11月30日 月曜日 午後1時43分
Attaching the unit to a wall
(optional)
This unit can be wall mounted using the supplied wall
mount brackets, etc. Make sure that the wall and the
screws used for securing to the wall are capable of
supporting at least 33 kg. The screws and other items
are not supplied as the type and size will vary with
each installation.
≥ Refer to step 5 of “Wall mount instructions” for details
about the required screws.
≥ As an additional protective measure, attach the unit
to the wall with the fall prevention cord.
Wall mount instructions
Before installation, turn the unit off and disconnect the
AC mains lead from the mains socket.
1
Detach the stand from the unit.
≥ Unscrew the fixing screw at the bottom of the unit.
≥ Gently pull the stand off the unit as illustrated.
≥ Keep the removed screw and the stand in a safe place.
Stand
Installation accessories
∫ Supplied accessories
≥ 1 Safety holder
≥ 1 Screw
≥ 2 Wall mount brackets
∫ Additionally required accessories
(commercially available)
Fixing screw
Soft blanket or cloth
2
≥ 4 Wall mount bracket fixing screws
≥ 1 Safety holder fixing screw
≥ 1 Fall prevention cord*
≥ 1 Screw eye
*
≥ Screw tightening torque: 50 N0cm to 70 N0cm.
Screw
(supplied)
Use a cord that is capable of supporting over 33 kg
(with a diameter of about 1.5 mm).
≥ Keep the safety holder out of reach of children to
prevent swallowing.
≥ Keep the screws out of reach of children to prevent
swallowing.
≥ Keep the wall mount brackets out of reach of children
to prevent swallowing.
Safety precautions
Fix the safety holder onto the unit with the screw
(supplied).
3
Attach the fall prevention cord (not supplied) to this
unit.
Cord
(not supplied)
Professional installation is required.
The installation should never be done by any
other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY
DAMAGE AND/OR SERIOUS INJURY,
INCLUDING DEATH RESULTING FROM
IMPROPER INSTALLATION OR INCORRECT
HANDLING.
WARNING:
To prevent injury, this apparatus must be securely
attached to the wall in accordance with the
installation instructions.
19
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 20 ページ
4
2015年11月30日 月曜日 午後1時43分
Measure and mark the position of both sides of the
wall mount brackets.
6
≥ Use figures below to identify the screwing positions.
Hook the unit securely onto the wall mount
brackets with both hands.
≥ Connect the antenna and the AC mains lead to the unit
before hanging the unit onto the wall. (l 5)
≥ After hanging the unit, release your hands carefully to
confirm the unit sits securely on the wall mount
brackets.
The position to attach the wall mount brackets
13 mm
204 mm
Wall
ュモャチモワヵバ
ョヮチモワヵ
ヘブ„
Space required
300 mm
142 mm
154 mm
75 mm
142 mm
7
500 mm
100 mm
5
Drive the safety holder fixing screw (not supplied)
to secure the safety holder onto the wall.
≥ Refer to step 5 for requirements before screwing.
100 mm
Attach the wall mount bracket to both sides of the
wall with two screws (not supplied).
≥ Use a level to ensure both wall mount brackets are
level.
Fix to the wall
At least 30 mm
Safety holder
Safety holder fixing screw
(not supplied)
‰7.5 mm to
‰9.4 mm
8
‰4 mm
Wall mount bracket
Attach the fall prevention cord (not supplied) to the
wall.
≥ Make sure that the slack of the cord is minimal.
Screw eye (not supplied)
Cord (not supplied)
Wall
20
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 21 ページ
2015年11月30日 月曜日 午後1時43分
Specifications
∫ GENERAL
Power consumption
26 W
Power consumption in standby mode*1, 2
Approx. 0.2 W
(When “BLUETOOTH STANDBY” is “ON”)*2
Approx. 0.3 W
Power supply
AC 220 V to 240 V, 50 Hz
Dimensions (WkHkD)
500 mmk205 mmk92 mm
Mass
Approx. 2.5 kg
Operating temperature range
0 oC to r40 oC
Operating humidity range
35 % to 80 % RH (no condensation)
∫ AMPLIFIER SECTION
Output power
RMS Output Power Stereo mode
Front Ch (both ch driven)
20 W per channel (8 ≠), 1 kHz, 10 % THD
Total RMS Stereo mode power
40 W
∫ TUNER SECTION
Preset Memory
FM 30 stations
Frequency Modulation (FM)
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals
75 ≠ (unbalanced)
∫ [SC-HC397] DAB SECTION
DAB memories
20 channels
Frequency Band (Wavelength)
Band III
5A to 13F
(174.928 MHz to 239.200 MHz)
Sensitivity *BER 4x10-4
Min Requirement
s98 dBm
DAB External Antenna
Terminal
F - Connector (75 ≠)
∫ DISC SECTION
Disc played (8 cm or 12 cm)
CD, CD-R/RW (CD-DA, MP3*3)
Pick up
Wavelength
790 nm (CD)
NORSK (NORWAY)
Bølgelengde
790 nm (CD)
Laserstyrke
Ingen farlig stråling sendes ut
(med sikkerhets-beskyttelse)
∫ SPEAKER SYSTEM SECTION
Speaker unit(s)
Full range
6.5 cm Cone typek1 per channel
Passive Radiator
8 cmk2 per channel
8≠
Impedance
∫ TERMINAL SECTION
USB Port
DC OUT 5 V 1.5 A
USB Standard
USB 2.0 full speed
Media file format support
MP3 (¢.mp3)
USB device file system
FAT12, FAT16, FAT32
AUX IN
Stereo, 3.5 mm jack
∫ Bluetooth SECTION
®
Version
Class
Supported Profiles
Bluetooth® Ver.2.1+EDR
Class 2
A2DP, AVRCP
Operating Frequency
2.4 GHz band FH-SS
Operation Distance
10 m Line of sight

≥ Specifications are subject to change without notice.
≥ Mass and dimensions are approximate.
≥ Total harmonic distortion is measured by a digital spectrum
analyser.
*1: “BLUETOOTH STANDBY” is “OFF”.
*2: No device is connected to the USB port before turning to
standby mode.
*3: MPEG-1 Layer 3, MPEG-2 Layer 3
21
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 22 ページ
2015年11月30日 月曜日 午後1時43分
Declaration of Conformity (DoC)
Hereby, “Panasonic Corporation” declares that this product is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Customers can download a copy of the original DoC to our R&TTE products from our DoC server:
http://www.doc.panasonic.de
Contact to Authorised Representative: Panasonic Marketing Europe GmbH,
Panasonic Testing Centre, Winsbergring 11, 22525 Hamburg, Germany
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household
waste.
For proper treatment, recovery and recycling of old products and used batteries, please take
them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol):
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
Safety information for customers in Norway
NORSK
ADVARSEL
FORSIKTIG
Produkt
Produkt
≥ For å redusere faren for brann, elektrisk støt eller skade på
apparatet:
– Utsett ikke produktet for regn, fukt, drypping eller sprut.
– Ikke plasser objekter som er fylt med væske, som vaser,
på apparatet.
– Bruk kun anbefalt tilbehør.
– Fjern ikke deksler.
– Reparer ikke denne enheten selv, overlat service til
kvalifisert servicepersonell.
≥ Dette produktet anvender en laser. Betjening av kontroller
eller justering eller andre inngrep enn de beskrevet i denne
bruksanvisning kan føre til farlig bestråling.
≥ Plasser ikke åpen ild, slik som levende lys, oppå apparatet.
≥ Dette apparatet er beregnet for bruk under moderate
klimaforhold.
Vekselstrømnett
≥ Nettstøpselet er trukket ut fra denne enheten.
Installer denne enheten slik at nettstøpselet umiddelbart kan
trekkes fra stikkontakten.
22
RQT0A88
Plassering
≥ For å redusere faren for brann, elektrisk støt eller skade på
apparatet:
– Ikke plasser apparatet i en bokhylle, et innebygget
kabinett eller et annet lukket sted. Pass på at produktet er
godt ventilert.
– Apparatets ventilasjonsåpninger må ikke dekkes til med
aviser, duker, gardiner eller lignende.
SC-HC397EB&EG&395EG~RQT0A88-B.book 23 ページ
2015年11月30日 月曜日 午後1時43分
23
RQT0A88
SC-HC397EB&EG&395EG~RQT0A88-B.book 24 ページ
2015年11月30日 月曜日 午後1時43分
For the United Kingdom and Ireland customers
Sales and Support Information
Customer Communications Centre
≥ For customers within the UK: 0344 844 3899
≥ For customers within Ireland: 01 289 8333
≥ Monday–Friday 9:00 am - 5:00 pm
(Excluding public holidays).
≥ For further support on your product, please visit our website: www.panasonic.co.uk
Direct Sales at Panasonic UK
≥ Order accessory and consumable items for your product with ease and confidence by phoning our
Customer Communications Centre
Monday–Friday 9:00 am - 5:00 pm
(Excluding public holidays).
≥ Or go on line through our Internet Accessory ordering application at www.pas-europe.com.
≥ Most major credit and debit cards accepted.
≥ All enquiries transactions and distribution facilities are provided directly by Panasonic UK.
≥ It couldn’t be simpler!
≥ Also available through our Internet is direct shopping for a wide range of finished products. Take a
browse on our website for further details.
(Bottom of product)
EU
Manufactured by:
Panasonic Corporation
Kadoma, Osaka, Japan
Importer for Europe: Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 11, 22525 Hamburg, Germany
Panasonic Corporation
Web Site: http://www.panasonic.com
C Panasonic Corporation 2015
p
RQT0A88-B
F1115MG0
Download PDF
Similar pages