IR Speed Dome
User Manual
V1.0.0
UD.6L0201D1030A01
Downloaded from www.Manualslib.com manuals search engine
1
User Manual of IR Speed Dome
Thank you for purchasing our product. If there is any question or request, please do not hesitate to
contact the dealer.
This manual is applicable to IR Speed Dome.
This manual may contain several technically inaccurate points or printing errors, and the content is
subject to change without notice. The updates will be added into the new version of this manual.
We will readily improve or update the products or procedures described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security
or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined
in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or
reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
2
User Manual of IR Speed Dome
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.
0100001030406
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
3
User Manual of IR Speed Dome
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid
danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to Cautions Follow these precautions to
prevent serious injury or death.
prevent potential injury or material
damage.
Warnings:
 Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard.
And source with 24VAC10% or 12VDC10% (depending on models) according to the
IEC60950-1 and Limited Power Source standard. The power consumption cannot be less than
the required value.
 Do not connect several devices to one power adapter as an adapter overload may cause
over-heating and can be a fire hazard.
 When the product is installed on a wall or ceiling, the device should be firmly fixed.
 To reduce the risk of fire or electrical shock, do not expose the indoor used product to rain or
moisture.
 This installation should be made by a qualified service person and should conform to all the local
codes.
 Please install blackouts equipment into the power supply circuit for convenient supply
interruption.
 If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the product yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
4
User Manual of IR Speed Dome
Cautions:
 Make sure the power supply voltage is correct before using the product.
 Do not drop the product or subject it to physical shock. Do not install the product on vibratory
surface or places.
 Do not expose it to high electromagnetic radiating environment.
 Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can
cause fatal damage to the product.
 The sensor may be burned out by a laser beam, so when any laser equipment is being used,
make sure that the surface of the sensor not be exposed to the laser beam.
 Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire or
electrical shock will occur. The operating temperature should be -30°C ~ 65°C (outdoor speed
dome) and -10°C ~ 50°C (indoor speed dome).
 To avoid heat accumulation, good ventilation is required for a proper operating environment.
 While shipping, the product should be packed in its original packing.
 Please use the provided glove when open up the product cover. Do not touch the product cover
with fingers directly, because the acidic sweat of the fingers may erode the surface coating of
the product cover.
 Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do
not use alkaline detergents.
 Improper use or replacement of the battery may result in hazard of explosion. Please use the
manufacturer recommended battery type.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
5
User Manual of IR Speed Dome
Table of Contents
Chapter 1
Overview .............................................................................................................................................. 6
1.1
Description ........................................................................................................................................................... 6
1.2
Functions .............................................................................................................................................................. 6
Chapter 2
Getting Started ..................................................................................................................................... 9
2.1
Power-up Action ................................................................................................................................................... 9
2.2
Basic Operations ................................................................................................................................................. 10
2.3
System-defined Presets ...................................................................................................................................... 10
2.4
On-screen Displays ............................................................................................................................................. 11
Chapter 3
Menu Operation ..................................................................................................................................12
3.1
Accessing and Operating the Menu ................................................................................................................... 12
3.2
Configuring System Information ........................................................................................................................ 13
3.2.1
Checking System Information......................................................................................................................... 13
3.2.2
Configuring System Parameters ..................................................................................................................... 14
3.3
Configuring Image Parameters ........................................................................................................................... 18
3.3.1
Configuring Camera Parameters .................................................................................................................... 18
3.3.2
Configuring Privacy Mask .............................................................................................................................. 23
3.4
Configuring PTZ Control Parameters .................................................................................................................. 24
3.4.1
Configuring PTZ Parameters .......................................................................................................................... 24
3.4.2
Configuring Presets ........................................................................................................................................ 26
3.4.3
Configuring Patrols ........................................................................................................................................ 27
3.4.4
Configuring Patterns ...................................................................................................................................... 29
3.4.5
Configuring Time Tasks .................................................................................................................................. 30
3.4.6
Configuring Zone ............................................................................................................................................ 32
3.4.7
Clearing PTZ Control Settings ....................................................................................................................... 33
3.5
Others................................................................................................................................................................. 34
3.5.1
Configuring Dome Authentication ................................................................................................................. 34
3.5.2
Restoring Default Dome Settings .................................................................................................................. 35
3.5.3
Restoring Default Camera Settings ............................................................................................................... 36
3.5.4
Rebooting the Dome ...................................................................................................................................... 36
Appendix .....................................................................................................................................................................37
Appendix 1 Lightning & Surge Protection ....................................................................................................................... 37
Appendix 2 RS485 Bus Connection ................................................................................................................................. 38
Appendix 3 24VAC Wire Gauge & Transmission Distance .............................................................................................. 41
Appendix 4 Table of Wire Gauge Standards ................................................................................................................... 42
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
6
User Manual of IR Speed Dome
Chapter 1 Overview
1.1 Description
Integrated with the built-in pan/tilt unit, the medium speed dome features highly sensitive response
and reliable performance. The speed dome can be adopted in various surveillance fields with its
full-integral functions and features, such as corridor, large venue, meeting room, station,
neighborhoods, etc.
Figure 1-1 Appearance
1.2 Functions
Note: The functions vary according to the different models of the speed dome.
 Limit Stops
The dome can be programmed to move within the limit stops (left/right, up/down).
 Self-adaptive Protocol
The speed dome is compatible with PELCO-D, PELCO-P, PRIVATE-Code, VICON, and KALATEL-312,
etc., and is capable of being self-adaptive to these protocols without selecting protocol by DIP
switch settings.
 Keyboard Control
The pan/tilt movement and zoom actions of dome can be controlled by the control keyboard, DVR,
matrix, etc.
 Scan Modes
The dome provides 5 scan modes: auto scan, tilt scan, frame scan, random scan and panorama scan.
 Preset Freezing
This feature freezes the scene on the monitor when the dome is moving to a preset. This allows for
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
7
User Manual of IR Speed Dome
smooth transition from one preset scene to another. It also guarantees that masked area will not be
revealed when the dome is moving to a preset.
 Presets
A preset is a predefined image position. When the preset is called, the dome will automatically
move to the defined position. The presets can be added, modified, deleted and called.
 Label Display
The on-screen label of the preset title, PT display, zoom, and time can be displayed on the monitor.
 Auto Flips
In manual tracking mode, when a target object goes directly beneath the dome, the video will
automatically flips 180 degrees in horizontal direction to maintain continuity of tracking. This
function can also be realized by auto mirror image depending on different camera models.
 Privacy Mask
This function allows you to block or mask certain area of a scene, for preventing the personal
privacy from recording or live viewing. A masked area will move with pan and tilt functions and
automatically adjust in size as the lens zooms telephoto and wide.
 3D Positioning
In the client software, use the left key of mouse to click on the desired position in the video image
and drag a rectangle area in the lower right direction, then the dome system will move the position
to the center and allow the rectangle area to zoom in. Use the left key of mouse to drag a rectangle
area in the upper left direction to move the position to the center and allow the rectangle area to
zoom out.
 Proportional Pan/Tilt
Proportional pan/tilt automatically reduces or increases the pan and tilt speeds according to the
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower than at wide
zoom settings. This keeps the image from moving too fast on the live view image when there is a
large amount of zoom.
 Auto Focus
The auto focus enables the camera to focus automatically to maintain clear video images.
 Day/Night Auto Switch
The speed domes deliver color images during the day. And as light diminishes at night, the speed
domes switch to night mode and deliver black and white images with high quality.
 Slow Shutter
In slow shutter mode, the shutter speed will automatically slowdown in low illumination conditions
to maintain clear video images by extending the exposure time. The feature can be enabled or
disabled.
 Backlight Compensation (BLC)
If you focus on an object against strong backlight, the object will be too dark to be seen clearly. The
BLC (Backlight Compensation) function can compensate light to the object in the front to make it
clear, but this causes the over-exposure of the background where the light is strong.
 Wide Dynamic Range (WDR)
The wide dynamic range (WDR) function helps the camera provide clear images even under back
light circumstances. When there are both very bright and very dark areas simultaneously in the field
of view, WDR balances the brightness level of the whole image and provide clear images with
details.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
8
User Manual of IR Speed Dome
 White Balance (WB)
White balance can remove the unrealistic color casts. White balance is the white rendition function
of the camera to adjust the color temperature according to the environment automatically.
 Patrol
A patrol is a memorized series of pre-defined preset function. The scanning speed between two
presets and the dwell time at the preset are programmable.
 Pattern
A pattern is a memorized series of pan, tilt, zoom, and preset functions. By default the focus and iris
are in auto status during the pattern is being memorized.
 Power Off Memory
The dome supports the power off memory capability with the predefined resume time. It allows the
dome to resume its previous position after power is restored.
 Time Task
A time task is a preconfigured action that can be performed automatically at a specific date and
time. The programmable actions include: pan scan, random scan, patrol 1-8, pattern 1-4, preset 1-8,
frame scan, panorama scan, tilt scan, day, night, and none.
 Park Action
This feature allows the dome to start a predefined action automatically after a period of inactivity.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
9
User Manual of IR Speed Dome
Chapter 2 Getting Started
2.1 Power-up Action
After the speed dome is power-on, it will perform a series of self-test actions. It runs the pan
checking firstly, then the tilt checking and the camera checking at last. After the power-up actions,
the system information will be displayed for 2 minutes on the live view screen as shown below.
ADDRESS
0
COM FORMAT
2400,8,1
PROTOCOL SELF ADAPTIVE
VERSION
X.XX
HARDVERSION
BUILD DATE
X.XX
XX XX XX
Figure 2-1 System Information
Table 2-1 Descriptions of the System Information
System Info
Description
TYPE
The model of the speed dome.
SN
The serial number of the speed dome.
ADDRESS
The default communication address of the speed dome.
COM Format
The communication settings of the speed dome, including baudrate
(2400 by default), data bit (8 by default) and stop bit (1 by default)
PROTOCOL
digit).
It is for the communication with other devices.
VERSION
The version of the firmware.
HARDVERSION
The version of the hardware.
BUILD DATE
The date when the program of the software is compiled.
Notes:
 You have to configure the address and the baudrate for the speed dome the same as those in
the control devices.
 The speed dome is self-adaptive to the PELCO-D, PELCO-P, PRIVATE-Code, VICON, and
KALATEL-312 protocols.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
10
User Manual of IR Speed Dome
2.2 Basic Operations
You can operate the speed dome using a control device, including the control keyboard, DVR, DVS,
etc. In this manual, accessing the speed dome via the web browser will be taken as an example.
Panning and tilting:
Click the direction buttons to control the pan and tilt movement of the speed dome.
Zooming:
Click the ZOOM+ and ZOOM- buttons to control the zooming.
Focusing:
Click the FOCUS+ and FOCUS- buttons to adjust the focus.
Iris:
Click the IRIS+ and IRIS- buttons to adjust the iris.
2.3 System-defined Presets
Purpose:
The section lists the system-defined presets with special functions. These presets cannot be edited
but can be only called through a control device, e.g. a DVS or web browser. To call the
system-defined presets remotely, you can choose the preset number from the list in the PTZ control
panel. Please refer to table below for details.
For instance, preset 99 is the “Start auto scan”. If you call the preset 99, the speed dome starts auto
scan function.
Table 2-2 System-defined Presets
Preset NO.
33
34
35
36
37
38
39
40
41
42
43
44
46
92
Function
Auto-flip
Return to home position
Patrol 1
Patrol 2
Patrol 3
Patrol 4
IR cut filter in
IR cut filter out
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Enable fast patrol
Enable limit stops
Preset NO.
93
94
95
96
97
98
99
100
101
102
103
104
105
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
Function
Set manual limit stops
Remote reboot
Access main menu
Stop scanning
Start random scanning
Start frame scanning
Start auto scanning
Start tilt scanning
Start panorama scanning
Patrol 5
Patrol 6
Patrol 7
Patrol 8
11
User Manual of IR Speed Dome
Note: For Manchester code control protocol, the system-defined presets with special functions are
shown as below:
Table 1-1 System-defined Presets of Manchester Code Control Protocol
Set Preset
NO.
65
66
69
70
71
72
Function
Remote reboot
Access main menu
Stop recording pattern
Record Pattern 1
Record Pattern 2
Record Pattern 3
Call Preset
NO.
67
70
71
72
Function
Auto-flip
Run Pattern 1
Run Pattern 2
Run Pattern 3
2.4 On-screen Displays
The speed dome supports following on-screen displays:
Zoom Show: Identifies the amount of magnification. The format is ZXXX. XXX is the zoom amount.
PT Show: Displays panning and tilting direction, with the format of NEXXX/TXXX. The NE followed
with XXX indicates the degrees in north east direction, while the T followed with XXX indicates the
degrees in tilt position.
Time Show: Displayed as Day/Month/Year/Day of Week/Hour/Minute. It supports 24-hour time
system.
Preset Show: After you call the configured preset, the preset number is displayed if the lens moves
to the certain place where you’ve set a preset for.
Zone Show: Display the zone title.
Address Show: Display the address of the speed dome.
Error Rate Show: Display the error rate of the speed dome.
Fan and Heat show: Display the heat information of the speed dome.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
12
User Manual of IR Speed Dome
Chapter 3 Menu Operation
Notes:
1. The operation interface of the different speed domes may differ. Please refer to the actual
operation interface.
2. You can click the left and right direction buttons in the PTZ control panel via the IE browser
of the DVR to enter the next page or return to the previous page of the submenu if more
than one page is available.
Figure 3-1 Main Menu
Before you start:
You can operate the speed dome using the on-screen display menu remotely by connecting to a
DVR or a DVS (encoder).
Examples of entering speed dome menu are listed as follows:
 Enter the menu by pressing buttons: PTZ -> REC -> 9 -> 5 on the front panel of the DVR.
 Enter the menu by pressing buttons: CALL -> 9 -> 5 -> ENTER on the keyboard.
 Enter the menu via the web browser of a DVR/DVS.
Menu operations via the web browser of a DVR will be taken as an example in this chapter.
3.1 Accessing and Operating the Menu
To enter the main menu:
Steps:
1. Connect the video and RS-485 cables of speed dome to a DVR.
2. Visit the DVR via the web browser.
3. View the live video of the speed dome.
4. For PELCO-P/D and other private PTZ protocols, call preset 95 from the preset list in the PTZ
control panel of the DVR.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
13
User Manual of IR Speed Dome
5. For some other protocols, e.g. Manchester code control protocol, call preset 66 to access the
menu. Please refer to Table 2-3 for details.
MAIN MENUS
<SYS INFO>
<DOME SETTINGS>
<RESTORE DEFAULTS>
<RESTORE CAMERA>
<RESBOOT DOME>
<LANGUAGE>
ENGLISH
<SET TITLE>
OFF
EXIT
Figure 3-2 Main Menu
To move the cursor and operate the menu:
 Move the cursor up/down: On the live view page of the web browser, click up/down direction
buttons or FOCUS + and FOCUS - buttons in the PTZ control panel to move the cursor up and
down.
 Enter/Exit: On the live view page of the web browser, click IRIS+ to enter a submenu; move the
cursor to Exit and click IRIS+ to exit.
To change the value of a parameter:
Steps:
1. Move the cursor to the target item and click IRIS+ button. You can see the shape of cursor
changes.
2. Click the up/down or left/right buttons in the PTZ control panel to choose the value from the
selectable value list.
3. Press IRIS+ to confirm the change or click IRIS- to cancel and restore the original value. You can
see the shape of cursor changes again.
3.2 Configuring System Information
3.2.1 Checking System Information
Purpose:
System information menu displays the current system information of the speed dome, including
model, address, protocol, etc. The information shown on this submenu is similar to the system
information shown after the power-up action. Please refer to Section 2.1 for more details.
Enter the system information display menu:
MAIN MENUS > SYS INFO
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
14
User Manual of IR Speed Dome
SYS INFO
ADDRESS
0
COM FORMAT
2400,8,1
PROTOCOL SELF ADAPTIVE
VERSION
1.00
HARDVERSION
1.00
BUILD DATE
13 04 01
TEMPERATURE
BACK
38℃
EXIT
Figure 3-3 System Information
Notes:
 Information on this menu cannot be edited.
 The temperature refers to the internal temperature of the speed dome.
3.2.2 Configuring System Parameters
Purpose:
You can check and also edit the system information of software address, baud rate, system time, etc.
on the system information settings menu.
SYS INFO SETTINGS
SOFT ADDRESS
1
SYS INFO SETTINGS
SYS INFO SETTINGS
ZERO ANGLE
PROTOCOL STATUS SET
PROTOCOL SET
SOFT ADDR ACTIVE
SOFT BAUD
OFF
2400
DISPLAY SETTINGS
SOFT BAUD ACTIVE
OFF
FAN CONTROL
N/A
BROADCAST ADDRESS
ON
PELCO CHECKSUM
ON
EIS FUNCTION
EIS LEVEL
OFF
N/A
SYS TIME
BACK
IR PARAMETER
485CHECK SET
PRESET DFOCUS
EXIT
BACK
OFF
AUTO MATCH
AUTO
POWER MEMORY
180S
OFF
EXIT
BACK
EXIT
Figure 3-4 System Information Settings
Note: You can click the left and right direction buttons in the PTZ control panel via the web browser
of the encoder to enter the next page and return to the previous page of the submenu if more than
one page is available.
 Dome address settings
To Set the Soft Address of the Speed Dome
If the SOFT ADDR ACTIVE is set as ON, the soft address is the valid address for connecting the speed
dome. The selectable soft address range is from 1 to 255;
If the SOFT ADDR ACTIVE is set as OFF, the hard address set by the DIP switch is the valid address of
the speed dome.
Notes:
 Before you set the soft address of the speed dome, you need to confirm that it is within the
control range of the control device (e.g. the DVR).
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
15
User Manual of IR Speed Dome

After you enable/disable the soft address, the speed dome will reboot automatically to
activate the settings.
To Set the Broadcast Address of the Speed Dome
When the BROADCAST ADDRESS is set to ON, the control device with address 0 is capable of
controlling all domes connected to it.
 Soft Baud Rate Settings
If the SOFT BAUD ACTIVE is set as ON, the soft baud rate is the valid baud rate for the speed dome,
with 2400, 4800, 9600 and 19200 selectable.
If the SOFT BAUD ACTIVE is set as OFF, the baud rate should be set by the DIP switch.
Note: After you enable/disable the soft baud rate, the speed dome will reboot automatically to
activate the settings.
 PELCO Checksum
The PELCO CHECKSUM is used for Pelco-P and Pelco-D protocols. If the video turns to slack or
uncontrollable, you can set the PELCO CHECKSUM as ON to improve the video quality.
 System Time Configuration
Steps:
(1) Move the cursor to SYS TIME using the direction buttons and click IRIS+ to enter.
(2) Click the left/right direction buttons to position the cursor on the specific item
(year/month/day or hour/minute/second) of which you want to change the value.
(3) Click the up/down direction buttons to increase/decrease the value.
(4) Click IRIS+ button to confirm the settings and exit.
Y- M- D
12 12 12
H- M- S
15 33 25
DONE: OPEN
QUIT: CLOSE
Figure 3-5 Set the System Time
 Zero Angle (Initial Position) Configuration
Purpose:
You can define the initial position of the speed dome on the ZERO ANGLE submenu.
Steps:
(1) Move the cursor to ZERO ANGLE using the direction buttons and click IRIS+ to enter.
(2) Click the left/right/up/down direction buttons to adjust the monitor angle of the speed dome.
(3) Click IRIS+ button to confirm the settings and exit.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
16
User Manual of IR Speed Dome
 Display Settings
Purpose:
You can enable or disable the on-screen display of PTZ movements, alarms, time, presets, zone,
address, error rate, and fan/heat show, etc.
Steps:
(1) Move the cursor to DISPLAY SETTINGS using the direction buttons and click IRIS+ to enter.
(2) Move the cursor to the target item and click IRIS+ and click up/down direction buttons to
choose each display mode as ON or OFF, and define each display time as 2 seconds, 5 seconds
or 10 seconds.
(3) Click IRIS+ button to confirm the settings.
Note: If you enable the OSD for both ZOOM and PT, while calling a preset, the preset No. will be
displayed on the screen till the preset scene passes.
DISPLAY SETTINGS
ZOOM SHOW
2
PT SHOW
2
TIME SHOW
ON
PRESET SHOW
ON
ZONE SHOW
ADDRESS SHOW
ON
ON
ERROR RATE SHOW
ON
BACK
EXIT
DISPLAY SETTINGS
FAN AND HEAT SHOW
BACK
OFF
EXIT
Figure 3-6 Display Settings
The speed dome shows the viewing direction when you manually control it to rotate.
Table 1-2 Viewing Direction Display
Display
N
NE
E
SE
S
SW
Indication North Northeast East Southeast South Southwest
Note: The north direction refers to the zero angle (initial position).
W
West
NW
Northwest
 IR Parameter Configuration
Purpose:
You can configure the IR parameters including the IR sensitivity, n/m LED current, reference height,
reference zoom, and LED control, fan control, switch delay, heat control, and IR correction, etc.
Enter the LED parameter submenu:
MAIN MENU > DOME SETTINGS > SYS INFO SETTINGS > IR PARAMETER
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
17
User Manual of IR Speed Dome
IR PARAMETER
IR SENSITIVITY
IR PARAMETER
MEDIUM
FAN CONTROL
TEMP
N/M LED CURRENT
8
SWITCH DELAY(SEC)
FAR LED CURRENT
8
HEAT CONTROL
TEMP
4
IR CORRECTION
N/A
REFERENCE HEIGHT
REFERENCE ZOOM
LED CONTROL
BACK
8
5
CLOSE
EXIT
BACK
EXIT
Figure 3-7 IR Parameter



Set the sensitivity of the IR LED.
You can set the IR SENSITIVITY to HIGH, MEDIUM, or LOW.
Set the electricity level of the IR LED.
The N/M LED CURRENT and the FAR LED CURRENT refer to the electricity level of the
near/middle IR LED and far IR LED correspondingly. You can set the near/far LED current and the
far LED current to HIGH, MEDIUM, and LOW.
IR LED switching settings
 REFERENCE HEIGHT.
Reference height refers to the mounting height of the speed dome. This value is for
switching between near/medium-distance IR LED and far-distance IR LED.
 REFERENCE ZOOM.
When the actual zooming rate is larger than the reference zoom, it will switch to the
far-distance IR LED; when it’s smaller than the reference zoom, it will switch to the
near/medium-distance IR LED.
 LED CONTROL.
LED control can be set to ALL ON (enable all the IR LED), FAR ON (enable far-distance IR LED),
NEAR ON (enable near/medium-distance IR LED), AUTO (enable IR LED automatically
according to the environment illumination), and CLOSE (disable IR LED).

IR LED switch delay
The SWITCH DELAY (SEC) refers to the delay time between the switch of far-distance IR LED and
N/M-distance IR LED.

Fan and heat settings
 FAN CONTROL is for adjusting the temperature of the speed dome’s circuit board. You can
set it to ON (normally on), OFF (normally off) or TEM (change according to the temperature).
 HEAT CONTROL is also to control the temperature of the speed dome in severe cold
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
18
User Manual of IR Speed Dome
surveillance environments, which can be set as ON (normally on), OFF (normally off) or TEM
(change according to the temperature).

IR correction settings
This parameter is to correct the focus problems caused by the IR light. You can turn IR CORRECTION
ON or OFF.
Note: IR correction settings vary according to the different camera models.
 Fan Parameter Configuration
You can set the FAN CONTROL as TEMP (controlled by the temperature), ON or OFF.
 EIS (Electronic Image Stabilization) Configuration
You can set the EIS FUNCTION as ON or OFF; and set the EIS LEVEL as 0-3.
Note: The selectable EIS level varies according to the different camera models.
 Preset Direct Focus
You can set the preset direct focus function ON/OF on PRESET DFOCUS submenu.

Protocol and RS-485 settings
 Select the protocol.
Choose the protocol on PROTO SET submenu. You can configure it as AUTO MATCH, PELCO-P,
PELCO-D, HIKVISION, KALATEL or VICON. When you choose AUTO MATCH, it is protocol
self-adaptive.
 Set the protocol status.
Set the PROTOCOL STATUS SET as ON to enable the user-defined protocol.
 Enable the RS-485 configuration diagnosis.
You can set 485CHECK SET as ON or AUTO for automatic RS-485 configuration diagnosis. If the
configuration is incorrect, an alert will be received; if you set the value as AUTO, it will
automatically stop the diagnosis when no errors exist.
 Power Memory Settings
The dome can resume its previous PTZ status or actions after it restarted from a power-off. You can
set the power memory to 10S, 30S, 60S, 180S, and 300S.
3.3 Configuring Image Parameters
3.3.1 Configuring Camera Parameters
Purpose:
You can set the camera parameters including focus, shutter speed, iris, etc.
Enter the camera parameters settings menu:
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
19
User Manual of IR Speed Dome
MAIN MENUS > DOME SETUP >CAMERA SETUP
CAMERA
CAMERA
FOCUS
AF
BLC/WDR
ZOOM LIMIT
22
BLC LEVEL
ZOOM SPEED
HIGH
SLOW SHUTTER
ON
IRCUT FILTER
D/N LEVEL
AUTO
1
SHARPNESS
BACK
8
N/A
AE MODE
AUTO
IRIS
10
SHUTTER
GAIN
50
N/A
EXPOSURE COMP
EXIT
BACK
7
EXIT
CAMERA
CAMERA
WHITE BALANCE
OFF
AUTO
210
WIDE LIMIT
CHROMA SUPPRESS
BLUE
150
SATURATION
1
IMAGE FLIP
OFF
CONTRAST
OFF
FOCUS LIMIT
INIT LENS
1M
OFF
HLC
ON
HR MODE
GAIN LIMIT
OFF
15
RED
NOISE REDUCE
BACK
LOW
EXIT
BACK
2.0
1
EXIT
Figure 3-8 Camera Settings
Task 1: Configure the focus settings.
 Setting the focus mode
Steps:
(1) Move the cursor to FOCUS using the direction buttons and click IRIS+ to enter.
(2) Click up/down direction buttons to set the focus mode to AF, MF or HAF.
AF (Auto-focus): The lens remains in focus during PTZ movements.
MF (Manual Focus): You need to adjust the focus with Focus+ and Focus- buttons manually.
HAF (Half-auto Focus): The speed dome focuses automatically only once after panning,
tilting and zooming.
(3) Click IRIS+ button to save the settings.
 Setting the focus limit
Purpose:
This function is used to limit the minimum focus distance. You can configure the focus limit
longer when the target is at a distance, to avoid the speed dome focusing on the objects close to
it; or configure the focus limit shorter when the target is near the speed dome, and avoid it
focuses on the objects father.
You can set FOCUS LIMT to 1CM, 30CM, 1M, 3M and AUTO to make sure that the speed dome
focuses on the target.
Note: The focus limit value varies according to the models of speed dome.
Task 2: Configure the zoom settings.
 Setting the zoom limit
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
20
User Manual of IR Speed Dome
Purpose:
Zoom limit is a user-defined limitation of the zoom amount (Zoom amount=optical zoom× digital
zoom). If you set the zoom limit to the minimum value, the digital zoom will be invalid and the
optical zoom will reach the maximum value; if you set the zoom limit smaller, the digital zoom
will be enabled.
Steps:
(1) Move the cursor to ZOOM LIMIT using the direction buttons and click IRIS+ to enter.
(2) Click up/down direction buttons to choose the limit from 22, 44, 88, 176, and 352.
(3) Click IRIS+ button to confirm.
Note: If you set the ZOOM LIMIT as the minimum value 22, the digital zoom function will be
disabled, and the optical zoom function is at its maximum value.
 Configure the zoom speed.
Purpose:
You can define the speed at which the lens changes from full wide zoom to the optical zoom.
Steps:
(1) Move the cursor to ZOOM SPEED using the direction buttons and click IRIS+ to enter.
(2) Click up/down direction buttons to choose the speed from HIGH (default), MEDUIM and
LOW.
(3) Click IRIS+ button to confirm.
Task 3: Configure the Day/Night mode.
There are two parameters available for day/night mode configuration.
(1) IR cut filter. It can be set as AUTO, DAY or NIGHT.
AUTO: The speed dome is capable of automatically switching from Black and White mode
(NIGHT) and Color mode (DAY) regarding to the lightening conditions. It is the default mode.
NIGHT (B/W): You can switch the IR cut filter into Black and White mode to increase then
lens sensitivity in low light conditions
DAY (Color): You can switch it to DAY mode in normal lighting conditions.
Note: You can set the IRCUT FILTER value on this menu, and you can call preset 39 to set the
IR cut filter mode to DAY mode and call preset 40 to set it as NIGHT mode.
(2) D/N level. The D/N level is the light level for auto D/N mode switch. As a dividing line, IR cut
filter switches between DAY and NIGHT when the light condition reaches the user-defined
D/N level. Three levels are selectable: HIGH, MID (default) and LOW.
Note: D/N level configuration varies according to the different camera models. Some
models don’t support user-defined D/N level.
Task 4: Configure the sharpness level.
The sharpness function can increase the gain of the image and sharpen the edges in the picture
to enhance the picture details. You can set the SHARPNESS level from 0 to 15.
Task 5: Configure the BLC and WDR.
There are two parameters available for BLC and WDR configuration on this menu.
(1) BLC/WDR. You can set the value as ON or OFF to enable or disable the functions.
(2) BLC LEVEL. You can manually adjust the backlight compensation level.
Note: BLC level configuration varies according to the different camera models. Some models
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
21
User Manual of IR Speed Dome
don’t support user-defined BLC level.
Task 6: Configuring the iris, gain and shutter speed
 Set the AE Mode
Purpose:
AE mode defines the priority of iris, shutter and gain while the speed dome adjusting the
brightness of the live view. You can change the mode on AE MODE submenu.
AUTO: Auto iris, auto shutter and auto gain. The speed dome adjusts the values automatically
responding to the lighting conditions. It is the default mode.
HAUTO: Half-auto mode allows you to adjust the iris manually while the camera is actually
adjusting the exposure automatically. HAUTO mode will switch to AUTO mode automatically if
there’s no iris adjustment within 20 seconds, or when the lighting changes in the environment.
IRIS: User-defined iris value, auto shutter and auto gain. It is the iris-priority mode. Please
define the iris value according to related content in this section if you choose IRIS mode.
SHUTTER: User-defined shutter speed, auto iris and auto gain. It is the shutter-priority mode.
Please define the shutter speed according to related content in this section if you choose
SHUTTER mode.
MANUAL: User-defined iris, gain and shutter. Please define the iris value, gain value and
shutter speed according to related content in this section if you choose MANUAL mode.
 Set the Iris Value
The IRIS value measures the amount of light entering to the lens. You can set the iris value from
0 to 17 in response to the changing light conditions.
Note: Iris is fully closed at value 0 and fully open at value 17.
 Set the Gain
1. Gain value. The value of gain indicates the amplification degree of the original image signal.
You can set the value from 0 to 15.
2. Gain limit. The higher gain value you set, the more noises will appear in the image. You can
set the maximum user configurable gain value from 0 to 15 to limit the gain range and control
the noises in the image.
Note: You need to change the IRCUT FILTER as DAY or NIGHT mode, and set the AE MODE as
MANUAL before you adjust the gain value.
 Set the Shutter
Purpose:
The speed of the electronic shutter controls the amount of light entering to the lens in a unit of
time (a second). You can manually configure the shutter speed for the speed dome, and you can
also enable the slow shutter function for low lighting circumstances.
(1) Shutter speed. The larger you set the SHUTTER value (the faster the shutter speed is), the
fewer the amount of entering light per second is, and the darker the image is. You can set
the value as 1, 2, 4, 8, 15, 30, 50, 125, 180, 250, 500, 1000, 2000, 4000 or 10000.
Note: The value of X indicates that the shutter speed is 1/X second. If you set the SHUTTER
value bigger (shutter speed is faster), the amount of entering light per second is fewer, and
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
22
User Manual of IR Speed Dome
the image is darker.
(2) Slow shutter. Set SLOW SHUTTER as ON, the shutter speed can automatically slow down to
extend exposure time under low lighting circumstances to obtain clearer image.
Task 7: Configure exposure compensation.
You can set the EXPOSURE COMP value from 0 to 14. The default value is 7. You can adjust this
value to increase the brightness of the image.
Task 8: Configure white balance.
You can set WHITE BALANCE mode as AUTO, INDOOR, OUTDOOR, SELFDEF (self-defined), ATW
(auto-tracking) and HAUTO (half-auto).
AUTO:
In Auto mode, the dome retains color balance automatically according to the current color
temperature.
INDOOR, OUTDOOR:
These two modes are for indoor use and outdoor use respectively.
SELFDEF:
In this mode, you can adjust the color temperature manually to meet your own demand.
Note: In SELFDEF mode, you need to adjust the RED and BLUE values manually.
ATW:
In auto-tracking mode, white balance is continuously being adjusted in real-time according to
the color temperature of the scene illumination.
HAUTO:
Selecting this mode, the viewed image retains color balance automatically according to the
current color temperature.
Task 9: Configure the image flip.
If you turn the IMAGE FLIP function on, the image will be flipped diagonally along its central
axis, shown as the mirror reflection of the image.
Task 10: Configure the INIT LENS.
You can turn INIT LENS on to trigger a spontaneous lens initiation to ensure the normal
operation.
Task 11: Configure the noise reduction.
To reduce the image noise, you can set the NOISE REDUCE to LOW, HIGH, MIDDLE, and OFF.
Task 12: Configure the image quality.
 Wide Limit
Set the wide limit ON can limit the minimum zoom of the lens.
Note: The wide limit function is supported by certain camera model series.
 Chroma Suppress
Set the Chroma suppress to ON can suppress the color noise so as to get the clear and high-quality
image in the low luminance environment.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
23
User Manual of IR Speed Dome
Note: The Chroma Suppress function is supported by certain camera model series.
 Saturation
Saturation indicates the brightness of the color. The higher the saturation, the brighter the color is.
Note: The saturation function is supported by certain camera model series.
 Contrast
Contrast is the degree of difference between the darker and lighter parts of the image.
Note: The contrast function is supported by certain camera model series.
 HLC
Set the HLC to ON can brighten the darker area and weaken the highlight area of the image.
Note: The HLC function is supported by certain camera model series.
 HR Mode
Set the HR MODE as ON to adjust the resolution higher. Switch it OFF to disable the function, which
can avoid cross color of the image.
3.3.2 Configuring Privacy Mask
Purpose:
Privacy mask enables you to cover certain areas on the live video from being live viewed and
recorded. The masked areas can move with the panning/tilting movements and automatically adjust
the size as the lens zooming in/out.
Steps:
1. Move the cursor to enter the privacy mask configuration submenu:
MAIN MENUS > DOME SETUP > PRIVACY SETUP
PRIVACY BLANK
BLANK NUM
1
BLANK STATUS
OFF
SET BLANK
DELE BLANK
BACK
EXIT
Figure 3-9 Privacy Mask Configuration Menu
2. Choose the privacy mask number:
Steps:
(1) Move the cursor to BLANK NUM and click IRIS+ to enter the editing mode.
(2) Click the up and down direction buttons to select a mask number for configuration.
(3) Click IRIS+ again to confirm and exit the editing mode.
Note: The configurable privacy mask number varies according to the camera models.
3. Configure the position and size of the privacy mask.
Steps:
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
24
User Manual of IR Speed Dome
(1) Move the cursor to SET BLANK and click IRIS+ button to enter the editing mode as shown in
the following figure. You can see a privacy mask on the live window.
ADJUST BLANK POS
FOCUS SHIFT STATUS
SAVE: OPEN
QUIT: CLOSE
Figure 3-10 Set the Privacy Mask
(2) You can see ADJUST BLANK POS message on the screen. Click the direction buttons to adjust
the position of the privacy mask to the designed scene.
(3) Click FOCUS+ button, and you can see ADJUST BLANK SIZE message on the screen. Click the
up/down buttons to increase/decrease the height of the mask and click right/left buttons to
increase/decrease the width of the mask. Click IRIS+ button to save the settings and return
to the previous menu and you can see the mask turn to gray.
(4) To modify the configured mask, click IRIS+ button to enter the SET BLANK menu and click
IRIS+ button again to modify.
Note: The tilt range for configuring the privacy masks is from 0° to 70°.
4. Enable or disable the privacy mask function.
Move the cursor to BLANK STATUS. Click IRIS+ button to enter the editing mode and click the up
and down direction buttons to set it ON or OFF.
Note: If no privacy mask has been configured, you cannot set the status as ON.
5. Delete the privacy mask.
You can enter the DELE BLANK menu to delete the current privacy mask.
3.4 Configuring PTZ Control Parameters
Purpose:
You can configure panning, tilting and zooming movements, and configure PTZ control functions
including presets, patrols, patterns, etc. for the speed dome.
3.4.1 Configuring PTZ Parameters
Enter PTZ configuration menu:
MAIN MENU > DOME SETTINGS > MOTION PARAMETER
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
25
User Manual of IR Speed Dome
MOTION
MOTION
AUTO FLIP
ON
PROPORTIONAL PAN
ON
PARK TIME
PARK ACT
5
NONE
SCAN SPEED
IMAGE FREEZE
28
OFF
DOME SPEED
BACK
PRESET SPEED
LIMIT STOP
4
OFF
<SETTING STOPS>
CLEAR STOPS
ELEVATION SET
ON
6
EXIT
BACK
EXIT
Figure 3-11 PTZ Configuration
 Auto-flip
In manual tracking mode, when a target object goes directly beneath the speed dome, the speed
dome automatically rotates 180 degrees horizontally for tracking.
Note: AUTO-FLIP is set as ON for this speed dome by default and it’s not user-definable.
 Proportional Panning
When the speed dome is zooming in/out, you can enable the proportional panning function to
automatically reduce or increase the panning and tilting speed according to the zooming amount.
This function enables the speed dome to trace the object at a proper speed when the speed dome
is zooming and the monitored scene is narrowed (zoom in) or enlarged (zoom out).
You can set PROPORTIONAL PAN as ON or OFF to enable/disable the function.
Note: This function is enabled automatically while setting the patterns.
 Park time and actions
Purpose:
This feature allows the speed dome to start a predefined action (park action: scan, preset, pattern,
etc.) automatically after a period of inactivity (park time).
You can set PARK TIME from 5 to 720 seconds and set the park action (PARK ACT) as preset 1-8,
pattern 1-4, patrol 1-8, pan scan, tilt scan, random scan, frame scan, panoramic scan, day mode,
night mode or none.
Note: If no control signal is received after the park time under the following circumstances, no park
actions will be performed: in the process of performing dome actions by calling special presets; or in
the process of performing external alarm linkage actions.
 Image freeze
This feature enables the live view to switch directly from the current scene to another scene that is
defined by a preset, without showing the middle areas between these two scenes. It reduces the
use of bandwidth in a digital network system and it also provides privacy protection for the middle
areas.
You can set IMAGE FREEZE as ON or OFF to enable or disable this function.
Note: The function varies according to the different camera models.
 PTZ speed
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
26
User Manual of IR Speed Dome
Purpose:
You can define the speed of the dome movements.
(1) DOME SPEED: The manual movement speed of the dome can be set from level 1 to 10.
(2) SCAN SPEED: The scan speed defines the scan degree per second of pan scan, tilt scan, frame
scan, random scan and panoramic scan. The scan speed is adjustable from level 1 to level 40 and
the higher the level is, the faster the scan speed is.
(3) PRESET SPEED: The speed of calling a preset can be set from level 1 to 8. The higher level
corresponds to the faster speed to call a preset.
 Limit stops
Purpose:
The limit stops are user-configurable stops which limit the panning and tilting area of the speed
dome. There are left, right, up and down limit stops to define an area.
Steps:
1. Move the cursor to LIMIT STOPS and click FOCUS+ to set it ON to enable this feature. Click IRIS+
to confirm the new settings.
2. Move the cursor to SETTING LIMIT STOPS and click IRIS+. You will see the message SET LEFT
LIMIT on the screen.
3. Click the direction buttons in the PTZ panel to configure the left limit stop. Click IRIS+ to confirm
the new settings.
4. Follow the prompts to configure the right, up and down limit stops on the menu.
Note: The new limit stops will overwrite the existed ones by default.
5. You can clear the defined limit stops. Click IRIS+ to enter CLEAR STOPS and click IRIS+ again to
clear the stops.
 Elevation set
You can set ELEVATION SET as ON to increase the elevation angle range of the speed dome or set it
as OFF to disable the function.
Note: The range of the elevation angle is 0-90° by default and it changes to -2°-90° when the
ELEVATION SET is set as ON.
3.4.2 Configuring Presets
Purpose:
A preset is a user-defined monitoring position/point. You can simply call the preset number to
change the monitor scene to the defined position.
Steps:
1. Move the cursor to enter preset configuration submenu:
MAIN MENU > DOME SETTINGS > PRESETS
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
27
User Manual of IR Speed Dome
PRESETS
PRESET NUM
1
[UNDEFINED]
PRESET PTZ
CLEAR PRESET
BACK
EXIT
Figure 3-12 Preset Configuration Menu
2. Choose the preset number:
Move the cursor to PRESET NUM and click IRIS+ to enter. Click the up and down buttons to
choose the preset number which needs to be edited. If the preset has been defined, the preset
label will be listed under the number; if it has not been defined, you will see the information
UNDEFINED under the number.
Notes:
 There are up to 255 presets can be set for the speed dome.
 The system-defined presets will be displayed on this submenu and they are not editable.
3. Set the preset position.
Move the cursor to PRESET PTZ and click IRIS+ to edit the preset position. Use the direction
buttons to move the speed dome to find the desired scene/position, and then press IRIS+ to
confirm the settings and return to the previous menu, or press IRIS- to cancel.
Note: The preset position settings will be restricted by the limit stops if they are defined.
4. Call the presets.
You can select the preset number from the drop-down preset list in the control panel of the
encoder through a web browser, and click the arrow to call a user-defined or system-defined
preset.
5. Clear the preset settings.
Move the cursor to CLEAR PRESET and click IRIS+ to clear the settings of the current preset.
3.4.3 Configuring Patrols
Purpose:
A patrol is a scanning track specified by a group of user-defined presets. You can call a patrol to scan
the scenes automatically among the user-defined presets in sequence.
Steps:
1. Move the cursor to enter patrol configuration submenu:
MAIN MENU > DOME SETTINGS > PATROLS
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
28
User Manual of IR Speed Dome
PATROLS
PATROL NUM
1
EDIT PATROL
PREVIEW
CLEAR PATH
PATROL_D
BACK
30S
EXIT
Figure 3-13 Patrol Configuration Menu
2. Choose the patrol number.
Steps:
(1) Move the cursor to PATROLS NUM and click IRIS+ to enter edit mode.
(2) Click the up and down direction buttons to select the number of the patrol which is to be
configured.
(3) Click IRIS+ again to confirm the settings and exit edit mode of this column.
Note: Up to 8 patrols can be configured.
3. Edit the patrol.
Steps:
(1) Move the cursor to EDIT PATROL and click IRIS+ to enter edit mode.
NUM PRESET DWELL SPEED
1
0
6
30
2
0
6
30
3
0
6
30
4
0
6
30
5
0
6
30
6
7
0
0
6
6
30
30
DONE: OPEN
QUIT:CLOSE
Figure 3-14 Edit the Patrol
(2) Click up/down direction buttons to choose the number and locate the preset to be edited.
(3) Click left/right direction buttons to position the cursor to the column of PRESET, DWELL and
SPEED. You can click the up/down direction buttons to set the value of preset number, dwell
time and patrol speed.
Note: The presets you set for a patrol should be the ones that have been pre-defined by
users. The dwell time (0-30 seconds selectable) is the time that the speed dome stays on a
certain preset; the patrol speed (level 1-40 selectable) is the scanning speed the speed dome
switching between the presets.
(4) Follow the above steps to define the other presets for the selected patrol. You can configure
up to 32 presets in sequence for a patrol. Press IRIS+ to save the new settings or press IRIS© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
29
User Manual of IR Speed Dome
4.
5.
6.
7.
to cancel and return to the previous menu.
Preview the patrol.
Move the cursor to PREVIEW and click IRIS+ to preview the current patrol. You can click IRS+
again to stop the preview.
Call the defined patrol.
You can call the special presets to call the defined patrol. E.g. call preset 35 to call patrol 1.
Please refer to Section 2.3 to find the corresponding preset number for each patrol.
Delete a patrol.
You can move the cursor to CLEAR PATH and click IRIS+ to delete the current patrol.
Define the dwell time when running the fast patrol.
If you call the No.46 preset to enable the fast patrol, the speed dome will run the patrol
automatically according to the route consists of the configured preset 1 to preset 32. And you
can set the Patrol_D time switches from one preset to the other. 5S, 10S, 20S, 30S, and 60S are
selectable.
3.4.4 Configuring Patterns
Purpose:
A pattern is a memorized, repeatable series of pan, tilt, zoom and preset movements that can be
recalled by a command or automatically performed by a configured function (alarm, park, time task,
and power-up).
Steps:
1. Move the cursor to enter the PATTERNS submenu:
MAIN MENU > DOME SETTINGS > PATTERNS
PATTERNS
PATTERN NUM
EDIT PATTERN
1
PREVIEW
CLEAR PATTERN
REMAINING
BACK
100
EXIT
Figure 3-15 Pattern Configuration Menu
2. Choose the pattern number.
Steps:
(1) Move the cursor to PATTERN NUM and click IRIS+ to enter edit mode.
(2) Click the up/down direction buttons to select the number of the pattern which is to be
configured.
(3) Click IRIS+ again to confirm the settings.
Note: Up to 4 patterns can be configured.
3. Edit the pattern.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
30
User Manual of IR Speed Dome
Steps:
(1) Move the cursor to EDIT PATTERN and click IRIS+ to enter edit mode.
REMAIN MEMORY
100
DONE: OPEN
QUIT: CLOSE
Figure 3-16 Edit the Pattern
(2) Click the PTZ control buttons and direction buttons to operate the speed dome to draw a
movement path, including pan scan, tilt scan, zoom in, zoom out, etc. The speed dome can
automatically memorize the path you operated as a pattern.
(3) Click IRIS+ again to save the pattern and exit edit mode.
Notes:
 REMAIN MEMORY indicates the remaining memory of the speed dome for configuring the
patterns. When it reaches 0, no more patterns can be configured. You can also see the
remaining memory shown under PATTERNS menu as REMAINING.
 The pan/tilt movements and the lens operations cannot be memorized simultaneously.
4. Preview the pattern.
Enter the PREVIEW menu to preview the current pattern.
5. Call the defined pattern.
You can call the special presets to call the defined pattern. E.g. call preset 41 to call pattern 1.
Please refer to Section 2.2 to find the corresponding preset number for each pattern.
6. Delete the patterns.
To Delete a Chosen Pattern
Click IRIS+ to enter EIDT PATTERN and you can see DEL PATH ABOVE. Click IRIS+ to delete the
pattern.
Note: If you delete the current pattern, the following pattern will also be deleted. E.g., if pattern
2 is deleted, pattern 3 and pattern 4 will be deleted as well.
To Clear All the Patterns
Enter CLEAR PATTERN menu and click IRIS+ to delete all the defined patterns.
3.4.5 Configuring Time Tasks
Purpose:
A time task is a preconfigured action that can be performed automatically at a specific date and
time.
Steps:
1. Move the cursor to enter the TIME TASK submenu:
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
31
User Manual of IR Speed Dome
MAIN MENU > DOME SETTINGS > TIME TASK
TIME TASK
TASK NUM
TASK STATE
TASK ACTION
1
ON
NONE
TASK TIME
TASK PREVIEW
TASK CLEAR
BACK
EXIT
Figure 3-17 Time Task Configuration Menu
2. Choose the task number.
Steps:
(1) Move the cursor to TASK NUM and click IRIS+ to enter edit mode.
(2) Click the up/down direction buttons to select the number of the task which is to be
configured.
(3) Click IRIS+ again to confirm the settings and exit the edit mode.
Note: Up to 8 time tasks can be configured.
3. Set the task status.
Steps:
(1) Move the cursor to TASK STATE and click IRIS+ to enter edit mode.
(2) Click the up/down direction buttons to set the task status to ON.
(3) Click IRIS+ again to confirm the settings and exit edit mode of this column.
Note: If the task action and task time have not been configured, you cannot set the status as
ON.
4. Configure the task action.
Steps:
(1) Move the cursor to TASK ACTION and click the IRIS+ to enter edit mode.
(2) Click the up and down direction buttons to select the task action from preset 1-8, pattern
1-4, patrol 1-8, pan scan, tilt scan, random scan, frame scan, panoramic scan, day mode,
night mode and none.
(3) Click IRIS+ again to confirm the settings and exit edit mode of this column.
5. Set the task time.
Steps:
(1) Move the cursor to TASK TIME and click IRIS+ to enter edit mode.
(2) Click the left and right direction buttons to position the cursor to WEEK, START (H-M) and
END (H-M).
(3) Click the up and down direction buttons to set the start time and end time to run the time
task.
(4) Click IRIS+ to confirm the settings and exit.
Note: The weekday can be set to be from Monday to Sunday or Whole Week; the H refers to
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
32
User Manual of IR Speed Dome
Hour and the M refers to Minute.
WEEK
WHOLE WEEK
START(H-M)
00
00
END(H-M)
00
00
DONE: OPEN
QUIT: CLOSE
Figure 3-18 Set the Task Time
6. Delete the task.
Move the cursor to TASK CLEAR, click IRIS+ to delete the time and action of the current task,
and click IRIS+ again to confirm the settings and exit.
3.4.6 Configuring Zone
Purpose:
A zone is a panning and tilting area defined by the left/right and up/down limit stops. You can
configure the zones on ZONES submenu. You can define a zone when the targeted surveillance
scene is limited.
Steps:
1. Move the cursor to enter the zone configuration submenu:
MAIN MENU > DOME SETTINGS > ZONES
ZONES
ZONE NUM
1
[UNDEFINED ]
EDIT ZONE
ZONE STATUS
SCAN STATUS
ON
ON
CLEAR ZONE
BACK
EXIT
Figure 3-19 Zone Configuration
2. Choose the zone number:
(1) Move the cursor to ZONE NUM and click IRIS+ button to enter the edit mode.
(2) Click the up and down buttons to select the zone number to be configured.
(3) Click IRIS+ again to confirm the settings and exit edit mode of this column.
Note: Up to 8 zones can be configured.
3. Configure the zone area.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
33
User Manual of IR Speed Dome
Steps:
(1) Move the cursor to EDIT ZONE and click IRIS+ button to enter the edit mode.
(2) You can see SET LEFT LIMIT on the screen. Click the direction buttons to set the left limit
stop.
(3) Follow the prompts on the screen to set the right limit, up limit and down limit.
(4) Click IRIS+ button to save the settings and exit.
4. Set the zone status and scan status.
ZONE STATUS: The zone status just indicates the current status of the zone.
SCAN STATUS: You can set the scan status to ON/OFF to enable/disable the scanning in the
zone.
Note: ZONE STATUS is not editable. After you edited the zone, it will switch to ON automatically;
if you delete the zone, the ZONE STATUS will switch to OFF.
5. Clear the zone settings.
Move the cursor to CLEAR ZONE, click IRIS+ to clear all the settings of the current zone, and click
IRIS+ again to confirm the settings and exit.
3.4.7 Clearing PTZ Control Settings
Purpose:
You can clear all user-defined PTZ control settings, including presets, patrols, patterns, zones and
time tasks. You can also clear privacy masks on this menu.
Steps:
1. Enter the CLEAR SETTINGS menu:
MAIN MENU > DOME SETTINGS > CLEAR SETTINGS
CLEAR SETTINGS
CLEAR ALL PRESETS
CLEAR ALL PATROLS
CLEAR ALL PATTERNS
CLEAR ALL BLANKS
CLEAR ALL ZONES
CLEAR ALL TIME TASKS
<DIAGNOSTICS>
BACK
EXIT
Figure 3-20 Clear Dome Settings
2. Move the cursor to each item, e.g., CLEAR ALL PATTERNS, and click IRIS+ to enter the
corresponding submenu. Click IRIS+ again to confirm the settings and exit.
On DIAGNOSTICS submenu, you can see the self-diagnostics information of the speed dome. For
more details, please refer to the table below.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
34
User Manual of IR Speed Dome
DIAGNOSTICS
DIAGNOSTICS
HIGH TEMP
0
HIGHEST TEMP
47°C
LOW TEMP
0
LOWEST TEMP
23°C
VIDEO LOSS
LOW VOLTAGE
0
0
POWER UP
BACK
PAN LOST
0
TILT LOST
CAMERA LOST
0
0
0
EXIT
BACK
EXIT
Figure 3-21 Self-diagnostics
Table 1-3 Descriptions of self-diagnostics information
Item
HIGH TEMP
HIGHEST TEMP
LOW TEMP
LOWEST TEMP
VIDEO LOSS
LOW VOLTAGE
Description
The occurrence times of high temperature (higher than 65°C)
The highest temperature
The occurrence times of low temperature (lower than -25°C)
d
The lowest temperature
The occurrence times of video loss
The occurrence times of low voltage (lower than the working voltage)
POWER UP
The occurrence times of abnormal reboot
PAN LOST
The occurrence times of panning loss
TILT LOST
The occurrence times of tilting loss
CAMERA LOST
The occurrence times of communication loss
Note: The panning loss and tilting loss refer to the failures of panning and tilting movement, and
are for diagnosing the electric motor of the speed dome.
3.5 Others
3.5.1 Configuring Dome Authentication
Purpose:
You can modify the password and enable/disable the password protection to prevent unauthorized
settings of the speed dome. After you set and enable the password, you need to input the password
every time you call preset 95 to enter the menu.
Steps:
1. Move the cursor to enter the password modification submenu:
MAIN MENU > DOME SETTINGS > PASSWORD > EDIT PASSWORD
2. Click IRIS+ to enter edit mode.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
35
User Manual of IR Speed Dome
3. Click the left/right buttons to select the digit of the current password and click up/down or
FOCUS+/- buttons to set the new value.
4. Click the right direction button to move the cursor to INPUT PW AGAIN and input the password
again.
5. Click IRIS+ to save the new settings and exit.
6. Enter the START USING submenu and switch the status to ON and click IRIS+ to save.
PASSWORD
START USING
INPUT PW
1 2 3 4 5 6
ON
EDIT PASSWORD
INPUT PW AG 1 2 3 4 5 6
DONE: OPEN
BACK
QUIT: CLOSE
EXIT
Figure 1-2 Set the Password
3.5.2 Restoring Default Dome Settings
Purpose:
You can reset all dome settings to factory default parameters as shown in the table below.
Note: Dome settings are mainly of PTZ parameters and alarm parameters, and also include some
system settings, e.g. dome address.
Enter default dome settings menu:
MAIN MENU > RESTORE DEFAUTLS
Click IRIS+ to restore the dome settings to the default value shown as the following table, or click
IRIS- to exit.
Table 1-4 Default Dome Settings
Parameters
Dome address
Baud rate
120Ω matching
resistance
Soft address
Focus
Zoom limit
Zoom speed
Slow shutter
IR cut filter
D/N level
BLC
Default Value
0
2400bps
Off
Off
HAF
Max Optical Zoom
High
Off
Day
Mid
Off
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
36
User Manual of IR Speed Dome
AE mode
Exposure
compensation
White balance
Auto-flip
Proportional pan
Park time
Park act
Scan speed
Image freeze
Limit stops
Time show
Zone show
Address show
Error rate show
Zoom/PT/Preset show
Auto
7
Auto
On
On
5 seconds
None
28
Off
Off
Off
On
Off
Off
Off
3.5.3 Restoring Default Camera Settings
Enter MAIN MENU > RESTORE CAMERA
Click IRIS+ to restore the camera settings to the default value; or click IRIS- to exit.
Note: Camera settings include the image parameters, lens settings and display settings.
3.5.4 Rebooting the Dome
Enter MAIN MENU > REBOOT DOME and click IRIS+ to reboot the speed dome remotely.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
37
User Manual of IR Speed Dome
Appendix
Appendix 1 Lightning & Surge Protection
This product adopts TVS plate lightning protection technology to avoid damage caused by pulse
signal that is below 3000W, like instantaneous lighting stroke, surging, etc. According to the actual
outdoor situation, necessary protection measures must be taken, besides ensuring the electrical
safety.
 The distance between signal transmission wires and High-voltage equipment or high-voltage
cable is at least 50m.
 Outdoor wiring should better be routed under eaves as much as possible.
 In the open field, wiring should be buried underground in sealed steel pipe, and the steel-pipe
should be one-point grounding. Overhead routing method is forbidden.
 In strong thunderstorm area or high induction voltage areas (such as high-voltage transformer
substation), high power lightning protection apparatus and lightning conductor are necessary to
be added.
 The design of lightning protection and grounding of the outdoor devices and cables should be
considered together with the lightning protection demand of buildings. It also must conform to
the related national standards and industrial standards.
 The system should be equipotential grounded. The grounding equipment must conform to the
demands of system anti-jamming and electrical safety both and it must not appear short circuit
or mixed circuit with the zero conductor of strong grid. When the system is grounded alone, the
resistance should be no more than 4Ω. The sectional area of the grounding cable should be no
less than 25mm2. For grounding instructions, please refer to the Installation Manual of Speed
Dome.
Figure A- 1 Lightning & Surge Protection
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
38
User Manual of IR Speed Dome
Appendix 2 RS485 Bus Connection
 General Property of RS485 Bus
According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has
120Ω characteristic impendence, the maximum load ability is 32 payloads (including controller
device and controlled device).
 RS485 Bus Transmission Distance
When using 0.56mm (24AWG) twisted-pair line, according to different baudrate, the maximum
transmission distance theory table is shown as below:
Table A-1 Max. Distance of RS485 Transmission
Baudrate
Max Distance
2400BPS
1800m
4800BPS
1200m
9600BPS
800m
The transmission distance will be decreased if we use the thinner cable, or use this product under
the strong electromagnetic interference situation, or there are lots of devices are added to the bus;
on the contrary, the transmission distance will be increased.
 Connection Methods
RS485 industry bus standard require daisy-chain connection method between any devices, both
sides have to connect a 120Ω terminal resistance (show as Diagram 1), the simplified connection
method is shown as diagram 2, but the distance of “D” should not be too long.
120Ω
120Ω
3#
2#
1#
32#
4#
Figure A-2 RS485 Connection 1
A+
D
BA+
主控器
B-
1#
2#
3#
31#
Figure A-3 RS485 Connection 2
 Problems in the Practical Application
Normally, users adopt star-shape connection method in construction, under this situation, the
terminal resistors must be connected between two farthest devices (as Figure 4, 1# and 15#), but
this connection method is not satisfy the requirement of the RS485 industry standard so that it will
lead to some problems such as signal reflection, anti-jamming ability decline when the devices are
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
39
User Manual of IR Speed Dome
faraway. At this time, the dome will be uncontrollable, or self-running, etc.
1#
6# 控
主 备
设
32#
15#
Figure A-4 Star Shape Connection
For such case, the best way is adding a RS485 distributor. This product can effectively change the
star-shape connection to which satisfies the requirement of RS485 industry standard, in order to
avoid those problems and improve the communication reliability. Show as figure 5.
485分配器
A+
120Ω
1#
B-
120Ω
2#
120Ω
16#
Figure A-5 RS485 Distributor
 Troubleshooting of RS485 communication
Problem
Possible Reasons
To Solve the Problem
1. Adjust the address and
1. The address or baudrate of the
baudrate of the remote control
speed dome does not match with
The speed
device to match with those of the
dome does those of remote control device.
speed dome.
the
2. The wire RS485+ connects to
2. Connect the wire RS485+ to the
self-test
the interface RS485- and wire
interface RS485+ and wire RS485action but
RS485- connects to the interface
to the interface RS485-.
cannot be
RS485+.
controlled
3. The RS485 wire is
3. Reconnect the RS485 wire
remotely.
disconnected.
tightly.
4. RS485 wire is broken.
4. Change a RS485 wire.
The speed
1. The connection is loose.
1. Reconnect the RS485 wire
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
40
User Manual of IR Speed Dome
Problem
dome can
be
controlled
but not
smoothly.
Possible Reasons
To Solve the Problem
tightly.
2. RS485+ or RS485-wire is
2. Change a RS485 wire.
broken.
3. The speed dome is too far away
3. Add a terminal resistor.
from the remote control device.
4. Too many speed domes are
4. Add a RS485 distributor.
connected.
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
41
User Manual of IR Speed Dome
Appendix 3 24VAC Wire Gauge & Transmission Distance
The following table describes the recommended max. distance adopted for the certain wire gauge
when the loss rate of 24VAC voltage is less than 10%. For the AC driven device, the maximum
voltage loss rate is 10% allowable. For example, for a device with the rating power of 80VA which is
installed at a distance of 35 feet (10m) away from the transformer, then 0.8000mm is required as
the minimum wire gauge.
0.8000
1.000
1.250
2.000
10
283(86)
451(137)
716(218)
1811(551)
20
141(42)
225(68)
358(109)
905(275)
30
94(28)
150(45)
238(72)
603(183)
40
70(21)
112(34)
179(54)
452(137)
50
56(17)
90(27)
143(43)
362(110)
60
47(14)
75(22)
119(36)
301(91)
70
40(12)
64(19)
102(31)
258(78)
80
35(10)
56(17)
89(27)
226(68)
90
31(9)
50(15)
79(24)
201(61)
100
28(8)
45(13)
71(21)
181(55)
110
25(7)
41(12)
65(19)
164(49)
120
23(7)
37(11)
59(17)
150(45)
130
21(6)
34(10)
55(16)
139(42)
140
20(6)
32(9)
51(15)
129(39)
150
18(5)
30(9)
47(14)
120(36)
160
17(5)
28(8)
44(13)
113(34)
170
16(4)
26(7)
42(12)
106(32)
180
15(4)
25(7)
39(11)
100(30)
190
14(4)
23(7)
37(11)
95(28)
200
14(4)
22(6)
35(10)
90(27)
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
42
User Manual of IR Speed Dome
Appendix 4 Table of Wire Gauge Standards
Bare Wire
Gauge(mm)
0.750
0.800
0.900
1.000
1.250
1.500
2.000
2.500
3.000
American
Wire Gauge
AWG
21
20
19
18
16
15
12
British Wire
Gauge SWG
21
20
19
18
17
14
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
Downloaded from www.Manualslib.com manuals search engine
Cross-sectional
Area of Bare
Wire(mm2)
0.4417
0.5027
0.6362
0.7854
1.2266
1.7663
3.1420
4.9080
7.0683
Downloaded from www.Manualslib.com manuals search engine
Download PDF
Similar pages