WWW.VENMAR.CA
RANGE HOOD
Series: VBNDH1
INSTALLATION, USE
AND CARE MANUAL
Serial number:
99045659-004A
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Cleaning and Maintenance . . . . . . . . . . . . . . . . . .6
Motors
Grease Filters
Non-Ducted Recirculation Filters
Fan Wheels
Stainless Steel Cleaning
Painted Finish Cleaning
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
Recommended Tools
and Accessories for Installation . . . . . . . . . . . .
Install Ductwork (Ducted Installations Only) . . .
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prepare the Hood . . . . . . . . . . . . . . . . . . . . . . .
Prepare the Hood Location . . . . . . . . . . . . . . . .
EZ1 Person Installation . . . . . . . . . . . . . . . . .
Install the Hood (EZ1 Bracket) . . . . . . . . . . . .
Standard Installation . . . . . . . . . . . . . . . . . . .
Install the Hood (Standard Installation) . . . . .
Connect the Wiring . . . . . . . . . . . . . . . . . . . . . .
Install the Filters . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
9-11
12
12-14
15-16
17
18
19
19
INSTALLATION MANUAL
TABLE OF CONTENTS
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . .20
2
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
READ AND SAVE THESE INSTRUCTIONS
! Intended for domestic cooking only !
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
Register your range hood online at www.venmar.ca
! WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
• Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
• Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
• Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, including
fire-rated construction.
• Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer’s guidelines and
safety standards such as those published by the National Fire Protection
Association (NFPA) and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local code authorities.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
• Do not use this unit with any additional solid-state speed control device.
• To reduce the risk of fire, use only metal ductwork.
• This unit must be grounded.
SAFETY
• When applicable local regulations comprise more restrictive installation
and/or certification requirements, the aforementioned requirements prevail
on those of this document and the installer agrees to conform to these at
his own expense.
INSTALLATION MANUAL
• As an alternative, this product may be installed with the UL-approved cord
kit designated for the product, following instructions packed with the cord
kit.
3
! WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low or
medium settings.
b) Always turn hood ON when cooking at high heat or when flambeing food
(i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating wheel frequently. Grease should not be allowed to
accumulate on blower wheel, filters or in exhaust ducts.
d) Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1.
SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE
FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL
THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels — This could
cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
! CAUTION
•
•
•
SAFETY
INSTALLATION MANUAL
•
4
•
•
•
•
•
For indoor use only.
For general ventilating use only. Do not use to exhaust hazardous or explosive materials
and vapors.
To avoid motor bearing damage and noisy and/or unbalanced wheel, keep drywall spray,
construction dust, etc. off range hood.
Your hood motor has a thermal overload which will automatically shut off the motor if it
becomes overheated. The motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
For best capture of cooking fumes, the bottom of the hood MUST NOT BE LESS than 18”
and at a maximum of 24” above the cooking surface.
Always follows the cooking equipment manufacturer’s requirements regarding the
ventilation needs.
To reduce the risk of fire and to properly exhaust air, be sure to duct air outside — Do not
exhaust air into spaces within walls or ceiling or into attics, crawl space or garage.
When installing, servicing or cleaning the unit, it is recommended to wear safety glasses
and gloves.
Please read specification label on product for further information and requirements.
Operation
Always turn your hood on before you begin cooking to establish an air flow in the kitchen.
Let the blower run for a few minutes to clear the air after you turn off the range. This will help
keep the whole kitchen cleaner and fresher.
Operate the hood as follows:
BLOWER BUTTON
When blower is OFF, press this button to turn ON the blower at the last saved speed. If there was
no speed saved, the blower will be set on LOW speed.
NOTE: When LOW speed is activated from OFF, the blower starts on MEDIUM speed for a very
short lapse of time, and then resumes to LOW speed.
To change the blower speed, press on this button again until the desired speed is reached (from
LOW to MEDIUM to HIGH speed to OFF). Each time a blower speed is activated, a beep is heard
and LED indicators light up to show the corresponding speed chosen (lower LED for LOW speed,
lower and center LEDs for MEDIUM speed and all LEDs for HIGH speed).
When blower is on (no matter the speed level), press and hold this button until the beep sound
ends; this will turn off the blower and save this blower speed to memory.
LIGHT BUTTON
When lights are OFF, press once on this button to turn ON the lights at the last saved setting. If
there was no light setting saved, the lights will be set on LOW intensity. Press another time to set
the lights on HIGH intensity. Pressing another time after the HIGH setting will turn OFF the lights.
Each time the lights are turned ON, a beep is heard and LED indicators light up to show the
corresponding intensity chosen (lower LED for LOW and both LEDs for HIGH).
When lights are on (no matter the lighting level), press and hold this button until the beep sound
ends; this will turn off the lights and save the chosen light intensity.
FILTER CLEANING REMINDER
When it is time to clean the hood and filters (refer to Cleaning and Maintenance on page 6), the
3 blower button LED indicators will flash slowly for 30 seconds after turning the blower OFF. This will
happen every time the blower is turned OFF until the filter cleaning reminder has been reset. Once
the cleaning is done, reset the filter cleaning reminder indicators by pressing on blower button for
3 seconds during the 30 seconds the 3 blower button LED indicators flash slowly.
INSTALLATION MANUAL
OPERATION
5
Cleaning and Maintenance
Proper maintenance of the Range Hood will assure proper performance of the unit.
MOTORS
The motors are permanently lubricated and never need oiling. If the motor bearings make
excessive or unusual noise, replace the motor with the exact service motor. The fan wheel should
also be replaced.
GREASE FILTERS
The grease filters should be cleaned frequently. Use a warm dishwashing detergent solution.
Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the
filters may occur if using phosphate detergents, or as a result of local water conditions - but this
will not affect filter performance. This discoloration is not covered by the warranty. To minimize or
prevent discoloration, hand wash filters using a mild detergent.
NON-DUCTED RECIRCULATION FILTERS
The non-ducted recirculation filters should be changed every 3 to 6 months. Replace more often
if your cooking style generates extra grease, such as frying and wok cooking. Refer to installation
instructions included with non-ducted recirculation filters.
FAN WHEELS
INSTALLATION MANUAL
CLEANING AND MAINTENANCE
The center of the fan wheels should be cleaned frequently. Use a clean cloth soaked with warm
detergent solution.
6
STAINLESS STEEL CLEANING
Do:
•
•
•
•
Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish
detergent.
Always clean in the direction of original polish lines.
Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
You may also use a specialized household stainless steel cleaner.
Don’t:
•
•
•
•
Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
Use any harsh or abrasive cleansers.
Allow dirt to accumulate.
Let plaster dust or any other construction residues reach the hood. During construction/
renovation, cover the range hood to make sure no dust sticks to the stainless steel surface.
Avoid when choosing a detergent:
•
•
•
Any cleaners that contain bleach will attack stainless steel.
Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces
rapidly.
Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc.,
are highly explosive and should never be used close to a range.
PAINTED FINISH CLEANING:
Clean with warm water and mild detergent only. If discoloration occurs, use a finish polish such
as automotive polish. (DO NOT use rough abrasive cleaner or porcelain cleaner.)
For ADA compliance installation guidelines, please visit www.broan-nutone.com
Recommended Tools and Accessories
for Installation
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Measuring tape
Phillips screwdriver no. 2
Nut driver or socket 11/32”
Flat blade screwdriver (to open knockout holes)
Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electrical access hole)
7/64” drill bit (to drill holes for EZ1 brackets mounting screws)
Wood shims (2) and wood screws (4) (required for standard installation to framed cabinet)
Saw (to cut holes for ducted application)
Sheet metal shears (ducted installation only, for duct adjustment)
Pliers (ducted installation only, for duct adjustment)
Metal foil duct tape (for ducted applications)
Scissors (to cut metal foil duct tape)
Pencil
Wire stripper
Strain relief, 1/2” diameter (to secure house wiring cable to the hood)
Install Ductwork (Ducted Installations Only)
ROOF CAP
3¼" X 10" OR
7" ROUND DUCT
(FOR VERTICAL
DISCHARGE)
SOFFIT
HOUSE WIRING
(TOP OR BACK OF HOOD)
CABINET
WALL CAP
HOOD
3¼" X 10" DUCT
(FOR HORIZONTAL DISCHARGE)
ABOVE COOKING SURFACE
1 ] Determine whether hood will discharge vertically (3¼” x 10” or 7” round),
or horizontally (3¼” x 10” only).
2 ] Decide where the ductwork will run between the hood and the outdoors.
3 ] Choose a straight, short duct run to allow the hood to perform most efficiently. Long duct
runs, elbows and transitions will reduce the performance of the hood. Use as few of them as
possible. When possible, use at least 2-foot straight runs before any turns. Larger ductwork
may be required for best performance with longer duct runs.
4 ] Install wall cap or roof cap (sold separately); ensure there is no leak in house insulation.
Connect metal ductwork to cap and work back towards the hood location. Use 2” metal foil
duct tape to seal the joints between ductwork sections.
INSTALLATION MANUAL
NOTE: Distances over 24” are at the installer and user discretion.
INSTALLATION
18" MIN - 24" MAX
7
Contents
Before proceeding to the installation, check the contents of the box. If items are missing or
damaged, contact the manufacturer.
Make sure that the following items are included:
* FIND INSIDE
OF HOOD
(1) 3¼” X 10”
DAMPER ASSEMBLY*
(2) GREASE FILTERS
(1) 7” ROUND
DUCT CONNECTOR
EZ1 COMPONENTS
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
MARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
FOR THE APPROPRIATE SIZE DUCT OPENING
7” ROUND DUCTING
OR
RECTANGULAR DUCTING
= 3¼” x 10”
= 3¼” x 14”
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
scale when installing to framed
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
conséquence.
CONDUIT ROND DE 7 PO
OU
CONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
TITLE TO BE TRANSLATED IN SPANISH
8”
C
L
To be translated in Spanish.
CONDUCTO REDONDO
DE 7 PULG.
O
CONDUCTO RECTANGULAR
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
7½”
V
Electrical access hole center
A = single blower hood
B = double blower hood
RTICAL
A EX
10½”
A
S
14½”
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
(1) TEMPLATE FOR DUCTING
(PRINTED BOTH SIDES)
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
4¼”
A
C
B
C
Place this edge against back wall
Appuyer ce bord au mur arrière
Apoyar este borde contra la pared de atrás
(2) INSTALLATION BRACKETS**
FOR FRAMED CABINET
(2) INSTALLATION BRACKETS**
FOR FRAMELESS CABINET
** FIND EZ1 BRACKETS ATTACHED INSIDE OF HOOD
(1) PARTS BAG*** CONTAINING:
(4) NO. 8-18 X 1/2”
METAL SCREWS WITH
(4) WASHERS
(6) NO. 8 X 5/8”
RD. HD.
WOOD SCREWS
(6) NO. 8 X 1/2”
COUNTERSUNK
WOOD SCREWS
INSTALLATION MANUAL
INSTALLATION
*** FIND PARTS BAG INSIDE OF HOOD
8
Prepare the Hood
1 ] If present, remove all protective polyfilm from the hood and/or parts.
2 ] Remove 7” Round Duct Plate from top/back of hood (see illustration below). Keep the screws
for further use.
7” ROUND
DUCT
PLATE
2 SCREWS
3 ] Using the finger cup, remove the grease filters from the hood by pushing down  and tilting
filters out .
B
C
4 ] Using a 11/32” nutdriver or socket, remove the lock nut retaining the flange of the right cover
plate (shaded part on illustration below) to the inner back of hood (see inset). Remove the
right cover plate retaining screws (7 screws), then set the blower cover along with its screws
and nut aside.
4
3
6
BACK OF HOOD
LOCK NUT
1
INSTALLATION MANUAL
2
7
INSTALLATION
5
9
5 ] Remove the damper assembly, taped over the EZ1 brackets, and the parts bag, taped on the
inner back of hood, near the left corner.
DAMPER ASSEMBLY
PARTS BAG LOCATION
NOTE: The damper assembly has to be slightly bent to fit inside the range hood. Once removed,
bend it back to ensure its opening is rectangular (4 corners at 90°).
6 ] Remove the EZ1 brackets from inside the hood by cutting off the tie wrap.
EZ1
BRACKETS
7 ] Remove Electrical Power Cable Knockout from top (vertical exhaust) or back (horizontal
exhaust) of hood. For knockout removed from back of hood, install an appropriate strain
relief, 1/2” diameter (not included). For knockout removed from top of hood, the strain relief
will be installed later.
ELECTRICAL
POWER CABLE
KNOCKOUT
INSTALLATION MANUAL
INSTALLATION
NON-DUCTED INSTALLATION ONLY
10
8 ] Remove 3 screws retaining the recirculation cover plate to the hood. Discard this plate with
its screws.
9 ] Peel off and discard the membrane covering the recirculation grille, ensuring the openings
are totally cleared.
RECIRCULATION
COVER PLATE
SCREWS
DUCTED INSTALLATION ONLY
8 ] Remove 3¼” x 10” vertical, 3¼” x 10” horizontal (both are the rectangular central
knockout plates, see hatched areas) or 7-inch round knockout plate as appropriate for
your ducting method (see FIGURES 1 A and 1 B).
FIGURE 1 A
7” ROUND KNOCKOUT
PLATE (ALSO REMOVE
3¼” X 10” VERTICAL
KNOCKOUT PLATE)
FIGURE 1 B
3¼” X 10”
VERTICAL
KNOCKOUT
PLATE
3¼” X 10”
HORIZONTAL
KNOCKOUT
PLATE
9 ] Attach 3¼” x 10” Damper Assembly on top OR back of hood (if using 3¼” x 10” duct; shaded
part in FIGURE 2 A below) or 7” Round Duct Plate (if using 7-inch round duct, FIGURE 3) over
the knockout opening. When installed, the 3¼” x 10” damper assembly must open as shown
in FIGURE 2 B.
FIGURE 2 A
FIGURE 2 B
SCREWS
3¼” X 10”
DAMPER
ASSEMBLY
DAMPER
FLAP
PIVOT
TOP/BACK
EDGE OF
HOOD
SCREWS
BACK OF
HOOD
3¼” X 10”
DAMPER
ASSEMBLY
DAMPER
FLAP
PIVOT
FIGURE 3
NOTE: To accommodate off-center ductwork, the 7” round duct plate can be installed up
to 1/2” on either side of the hood center.
TIP: Insert a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting) or
7” round (for round ducting) and seal the joint using aluminum foil duct tape to ease connection
with the house ductwork.
INSTALLATION MANUAL
SCREWS
INSTALLATION
7” ROUND
DUCT
PLATE
11
Prepare the Hood Location
NOTE: Before starting installation, read all the steps of these instructions.
Use the illustration below to identify your kitchen cabinet type.
FRAMED CABINET
FRAMELESS CABINET
This manual covers 2 kinds of installation: the standard (without EZ1 brackets)
and the EZ1 one-person installation system (using included template and brackets).
For the standard installation, go to page 17.
EZ1 one-person installation system
EZ1 installation is designed for use with kitchen cabinets that have the same width designation as
the range hood width. If the cabinet is greater than 1/2” wider than the range hood width, please
use the standard installation method.
1 ] Use the proper template for vertical OR horizontal disharge (included) for placement of
ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a
duct access hole, only cut the hole for electrical wiring. If replacing a hood and plan to use
the existing duct and electrical, steps 2 to 5 may not be necessary. If so, skip to step 6.
2 ] Measure and mark the hood center line on cabinet bottom.
3 ] Align the center line on template with the hood center line marked on the bottom of the
cabinet, placing the edge (where indicated) of the template against back wall. When using
with framed cabinet for vertical exhaust installation, fold over rear edge of template equal
to the depth of the cabinet frame at the wall (use graduations on template, C locations on
template). Tape the template in place.
NOTE: When facing the installation, A and B (on template) must be at right.
CABINET FRONT
VERTICAL EXHAUST
DUCTING
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
MARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
7” ROUND DUCTING
OR
MARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
FOR THE APPROPRIATE SIZE DUCT OPENING
RECTANGULAR DUCTING
= 3¼” x 10”
FOR THE APPROPRIATE SIZE DUCT OPENING
7” ROUND DUCTING
OR
RECTANGULAR DUCTING
= 3¼” x 10”
= 3¼” x 14”
= 3¼” x 14”
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
C
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
Bend template along graduated
scale when installing to framed
cabinet.
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
LE FORMAT DE CONDUIT UTILISÉ
CONDUIT ROND DE 7 PO
OU
C
CONDUIT RECTANGULAIRE
= 3¼ po x 10 po
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
conséquence.
= 3¼ po x 14 po
TITLE TO BE TRANSLATED IN SPANISH
8”
CL
To be translated in Spanish.
CONDUCTO REDONDO
DE 7 PULG.
O
Bend template along graduated
scale when installing to framed
cabinet.
10½”
INSTALLATION
INSTALLATION MANUAL
A
C
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
4¼”
B
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
A
C
B
C
Apoyar este borde contra la pared de atrás
FOLD TEMPLATE ALONG GRADUATED
P
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
10½”
CENTER LINE
C
CONDUCTO RECTANGULAR
14½”
C
Appuyer ce bord au mur arrière
O
VERTICAL
V
RTICAL
A EX
EXHAUST
A S
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
4¼”
14½”
CONDUCTO REDONDO
DE 7 PULG.
7½”
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
SCALE WHEN INSTALLING TO FRAMED
ELECTRICAL
ACCESS HOLE
LOCATION (B)
(IN CABINET BOTTOM)
CABINET.
HORIZONTAL EXHAUST
DUCTING
CENTER LINE
A
Place this edge against
cabinet bottom.
Appuyer ce bord contre le bas
de l’armoire.
Apoyar este borde contra
la base del armario.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
B
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
CL
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
12
= 3¼ po x 14 po
CL
To be translated in Spanish.
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
7½”
CONDUIT RECTANGULAIRE
TITLE TO BE TRANSLATED IN SPANISH
8”
CONDUCTO RECTANGULAR
OU
= 3¼ po x 10 po
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
conséquence.
VERTICAL
V
RTICAL
A EX
EXHAUST
A S
Place this edge against back wall
CONDUIT ROND DE 7 PO
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
MARK WHERE INDICATED
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
FOR THE APPROPRIATE SIZE DUCT OPENING
LE FORMAT DE CONDUIT UTILISÉ
RECTANGULAR DUCTING
CONDUIT RECTANGULAIRE
= 3¼” x 10”
= 3¼” x 14”
B
ess hole center
wer hood
wer hood
= 3¼ po x 10 po
= 3¼ po x 14 po
TITLE TO BE TRANSLATED IN SPANISH
CONDUCTO RECTANGULAR
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
HORIZONTAL
T
EXHAUST
ELECTRICAL
ACCESS HOLE
LOCATION (B)
(IN WALL)
B
4 ] Drill a 1/8” dia. pilot hole for house wiring, at B location on template.
5 ] Use a sharp pencil or 1/8” drill bit to mark the locations for the appropriate duct access
holes (16 locations for 7” round duct, or 4 corner locations for rectangular duct). Remove the
template.
6 ] Draw the border for the exhaust ducting by linking its marks (16 for round duct and 4 for
rectangular duct), then cut the opening in the cabinet bottom (vertical exhaust) or in the wall
(horizontal exhaust). Drill the house wiring hole by using a 1½” hole saw centered with the
pilot hole previously made in 4.
7 ] Install the proper installation brackets according to the type of cabinet (framed or frameless).
See below.
FRAMED CABINET
Refer to the marking on brackets to determine the correct installation side and orientation.
7/64”
of bracket against the wall. Use a pencil to mark 3 holes (there are 6 holes but only
3 are necessary).
Remove the bracket. Using a 7/64” drill bit, drill 3 holes where marked.
Assemble the bracket to the side frame using a Phillips screwdriver and 3 provided
no. 8 x 5/8” wood screws. Repeat for the other side frame.
INSTALLATION MANUAL
Mate the corresponding bracket to the cabinet side frame, while placing rear end
INSTALLATION
13
FRAMELESS CABINET
Refer to the marking on brackets to determine the correct installation side and orientation.
3X
INSTALLATION MANUAL
INSTALLATION
7/64”
14
Align the corresponding bracket to the cabinet side, while placing rear end of bracket
against the wall. Draw a line on the outer edge of the bracket (as shown).
Slide the bracket towards the center of cabinet and align outside edge of the bracket to
marked line, keeping the rear end edge leaning on the wall.
 Use a pencil to mark 3 holes.
Remove the bracket. Using a 7/64” drill bit, drill 3 holes where marked.
Assemble the bracket to the cabinet bottom using a Phillips screwdriver and 3 provided
countersunk wood screws. Repeat for the other cabinet side.
Install the Hood (EZ1 Bracket)
NOTE: The following procedure applies to both frame or frameless cabinet installations.
1 ] Run house power cable between service panel and hood location.
2 ] There are 2 pairs of recessed holes on each side of the top of the hood (on rear: A and B,
on front C and D on illustration below); these holes allow the range hood to hang on the
brackets (previously installed).
C
A
D B
HORIZONTAL EXHAUST INSTALLATION ONLY
3 ] Temporarily hang the hood on the brackets using its (2) recessed REAR HOLES (A and B).
While holding the hood, run the house power cable into the hood through the strain relief
previously installed in step 7 on page 10.
A
B
4 ] Unhook the rear holes from the brackets and hang the hood using its (2) recessed FRONT
HOLES (C and D). While holding the hood, go to step 6.
VERTICAL EXHAUST INSTALLATION ONLY
6 ] Connect ductwork to hood and use metal foil duct tape to make joints secure and air-tight.
Make sure the damper assembly (or round duct plate) enters the ductwork and that the
damper opens and closes freely.
INSTALLATION MANUAL
DUCTED INSTALLATION ONLY
INSTALLATION
5 ] Hang the hood on the brackets using the (2) recessed FRONT HOLES (C and D). While
holding the hood, tighten an appropriate strain relief, 1/2” diameter (not included) to the
power cable, then insert the strain relief in the knockout hole.
15
7 ] For framed cabinet, secure the hood to the EZ1 brackets using four (4) no. 8-18 x 1/2” metal
screws with washers (screws and washers included in parts bag). Insert two (2) screws and
washers per side, in the slots (as shown in inset on illustration below).
8 ] For frameless cabinet, secure the hood to the cabinet using four (4) no. 8 x 5/8” round head
wood screws (screws and washers included in parts bag). Insert two (2) screws and washers
per side, in the slots (as shown in inset on illustration below).
FRAMED
CABINET
METAL
SCREWS
INSTALLATION MANUAL
INSTALLATION
9 ] Attach power cable to the hood using the strain relief.
16
FRAMELESS
CABINET
WOOD
SCREWS
Standard Installation (without EZ1 brackets)
1 ] Use the proper diagram below for placement of ductwork and electrical cutout in cabinet
or wall. For a non-ducted installation, DO NOT cut a duct access hole, only cut the hole for
electrical wiring.
3¼" X 10"
CENTER LINE
VERTICAL DUCTING
WOOD SHIMS
(RECESSED-BOTTOM
CABINET FRONT
CABINETS ONLY)
CABINET
BOTTOM
5¼"
9¾"
5¼"
1Ǫ"
VERTICAL DUCT
ACCESS HOLE
47/16"
3/4"
1½"
ELECTRICAL ACCESS
HOLE (IN CABINET BOTTOM)
12Ǭ"
12Ǭ"
REAR HOOD MOUNTING SCREWS (2)
WOOD SHIMS
(RECESSED-BOTTOM
CABINETS ONLY)
3¼" X 10"
HORIZONTAL DUCTING
CABINET FRONT 13/16"
3/16"
HORIZONTAL DUCT
ACCESS HOLE
3Ǭ"
CABINET
BOTTOM
5¼"
5¼"
9¾"
12Ǭ"
REAR HOOD
MOUNTING
SCREWS (2)
12Ǭ"
ELECTRICAL
ACCESS HOLE
(IN WALL)
CENTER
LINE
CENTER LINE
WOOD SHIMS
(RECESSED-BOTTOM
CABINETS ONLY)
8" DIA.
HOLE
Ǫ
1½"
ELECTRICAL ACCESS
HOLE (IN CABINET BOTTOM)
12Ǭ"
REAR HOOD MOUNTING SCREWS (2)
2 ] Install part-way 2 ROUND HEAD no. 8 x 5/8” mounting screws into shims/cabinet, according
to the proper diagram above, the other 2 ROUND HEAD no. 8 x 5/8” mounting screws will be
used later. Mounting screws are included in parts bag, but wood shims and shim mounting
screws are not.
INSTALLATION MANUAL
12Ǭ"
9¾"
INSTALLATION
7-IN. ROUND
DUCT
ACCESS
4¹¹/16" HOLE
7-IN. ROUND
VERTICAL DUCTING
17
Install the Hood (Standard Installation)
NOTE: Two installers are recommended because of the weight of this hood.
1 ] Run house power cable between service panel and hood location. For hood with power
cable access located on back of hood, run the house power cable into the hood through
the strain relief previously installed in step 7 on page 10. For hood with power cable access
located on top, tighten the strain relief to the power cable before inserting the strain relief in
the knockout hole.
2 ] Hang hood from 2 rear mounting screws previously installed. Slide hood back towards wall
until mounting screw heads are engaged in narrow end of keyhole slots in top of hood.
Tighten screws securely and maintain a hold on the hood until completing step 3.
INSTALLATION MANUAL
INSTALLATION
3 ] Secure the hood to the cabinet using 2 no. 8 x 5/8” round head wood screws and 2 washers
(screws and washers included in parts bag). Insert 1 screw and washer per side, in the slots
(as shown below). Attach power cable to the hood using the strain relief.
18
Screw previously
tightened in step 2.
BACK OF HOOD
DUCTED INSTALLATION ONLY
4 ] Connect ductwork to hood and use metal foil duct tape to make joints secure and airtight.
Make sure that the damper assembly (or round duct plate) enters the ductwork and that
the damper opens and closes freely.
Connect the Wiring
! WARNING
Risk of electric shock. Electrical wiring must be done by qualified
personnel in accordance with all applicable codes and standards.
Before connecting wires, switch power off at service panel and lock
service disconnecting means to prevent power from being switched
on accidentally.
MOTORS
GROUND
WIRE
GROUND
SCREW
HOUSE
POWER CABLE
1 ] Connect House Power Cable to range hood wiring: BLACK to BLACK, WHITE to WHITE and
GREEN or bare wire under GREEN ground screw.
5
4
3
6
2
7
1
BACK OF HOOD
1
LOCK NUT
Ducted Installation Only:
Re-install grease filters removed in step 3 , page 9, under “Prepare the Hood”.
Non-ducted Installation Only:
Purchase two non-ducted filters from your local distributor or retailer (see product specification
label for filter type). Attach the non-ducted filters following instructions packed with the nonducted filters.
INSTALLATION MANUAL
Install the Filters
INSTALLATION
2 ] Reinstall the blower cover plate (shaded part on illustration above) using the lock nut
and 7 screws previously removed in step 4 on page 9. Pay attention to screw 1 location; from
back of hood point of view, it must be located on left side of the lock nut (see inset).
19
Ground
Neutral
Line
User interface mounted
to J10 on back of
control board.
J10
8
7
6
5
4
3
2
1
W
BK
7
6
5
4
3
2
1
1
2
3
4
5
4
3
2
1
Control Board
Interface
Override
J6
1 2 3 4 5 6
WIRING DIAGRAM
INSTALLATION MANUAL
120 V AC
J4
J1
J2
LED
Transformer
Power, Motor
20
BK
BK
BL
BN
BN/S
G/Y
O
BL
G/Y
BK (High)
O (Medium)
R (Low)
PP
BL
R
W
R
BK
R
BK
Fuse 5 A
PN
PP
R
W
Y
COLOR CODE
BLACK
BLUE
BROWN
BROWN/STRIPE
GREEN/YELLOW
ORANGE
BK
W
W
PINK
PURPLE
RED
WHITE
YELLOW
1
2
3
4
5
W
W
1
2
3
4
5
W
PP
PP
G/Y
BK
O 120
BL 88
PP 60
PN 45
Y 10
W
W
LED
LED
G/Y
6
5
4
3
2
1
6
5
4
3
2
1
W
O
BK
G/Y
R
FAN MOTOR
W
O
BK
G/Y
R
FAN MOTOR
BN/S
BN
BN/S
BN
BK
BK
BK
BK


L








KEY NO.
PART NO.
DESCRIPTION
QUANTITY
30"
30"
WHITE
S97020360
*
*
*
S97020466
S99527587
S97020470
2
3
4
5
6
7
8
9
10
11
STAINLESS
1
1
1
1
2
1
2
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
* ITEM NOT SHOWN.
REPLACEMENT PARTS AND REPAIRS
In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts only.
Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the
applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage
and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC recommends to
contact a certified service depot for all replacement parts and repairs.
INSTALLATION MANUAL
*
1
RECIRCULATION COVER PLATE, STAINLESS STEEL (INCLUDING SCREWS)
RECIRCULATION COVER PLATE, WHITE (INCLUDING SCREWS)
7'' ROUND DUCT PLATE (INCLUDING SCREWS)
3¼” X 10” DAMPER ASSEMBLY (INCLUDING SCREWS)
CAPACITOR (INCLUDING TIE WRAP)
BLOWER ASS'Y CW (INCLUDING ITEMS 4 AND 6 AND HARDWARE)
CLIP FOR FANPELLER
GREASE FILTER - MICRO MESH - OBLONG -TYPE C3 (SET OF 2)
BLOWER ASS'Y CCW (INCLUDING ITEMS 4 AND 6 AND HARDWARE)
AUTOTRANSFORMER (WITH SCREWS)
LED MODULES (PAIR)
CAPTOUCH CONTROL LED, STAINLESS (WITH SCREWS)
CAPTOUCH CONTROL LED, WHITE (WITH SCREWS)
WIRE HARNESS WITH AUTOTRANSFORMER AND FUSE
PARTS BAG INCLUDING: 4 METAL SCREWS NO. 8-18 X 1/2”, 4 WASHERS, 6 ROUND HEAD
NO. 8 X 5/8” WOOD SCREWS, 6 NO. 8 X 1/2” COUNTERSUNK WOOD SCREWS
NON-DUCTED FILTER - TYPE XC (SET OF 2) (NON-DUCTED INSTALLATION ONLY)
NON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS)
EASY INSTALL KIT (INCLUDING HARDWARE)
SERVICE PARTS
*
S97020031
S97020030
S97018567
S97020534
S97020412
S97020842
SR99420635
S99010431-002
S97020843
S97020797
S97020444
S97020431
S97020432
S97020796
21
WARRANTY
INSTALLATION MANUAL
22
Limited Warranty
Warranty Period and Exclusions: Venmar Ventilation ULC (the “Company”) warrants to the original consumer purchaser
of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for
a period of one (1) year from the date of original purchase (or such longer period as may be required by applicable law). For
Range Hood Product that includes built-in LED modules, the Company warrants the LED modules and driver to be free from
material defects for a period of three (3) years from the date of purchase. The limited warranty period for any replacement
parts provided by the Company and for any Products repaired or replaced under this limited warranty shall be the remainder
of the original warranty period (or such longer period as may be required by applicable law).
This warranty does not cover fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof
caps, wall caps and other accessories for ducting that may be purchased separately and installed with the Product. This
warranty also does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or parts
which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance,
storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use contrary
to recommendations or instructions, (e) any Product that has been moved from its original point of installation, (f) damage
caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or
nonresidential use, or (j) damage caused by fire, flood or other act of God or (k) Products with altered, defaced or removed
serial numbers. This warranty covers only Products sold to original consumers in Canada by the Company or its Canadian
distributors authorized by the Company.
This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer
purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective
products. The foregoing warranties are exclusive and in lieu of any other warranties and conditions, express or implied. THE
COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS
AND EXCLUDES ALL WARRANTIES AND CONDITIONS IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law
prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition is
limited to the period specified for the express warranty above. Some jurisdictions do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is for the
sole purpose of identifying it and shall not be construed as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid
under applicable law, but if any provision is held to be prohibited or invalid, such provision shall be ineffective only to the
extent of such prohibition or invalidity, without invalidating the remainder of such provision or the other remaining provisions
of the Limited Warranty.
Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or
repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and in
breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product or
replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping, insurance or
other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to
the Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible
for damage in transit. The Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured
Products or parts in the warranty repair or replacement process. Such Products and parts will be comparable in function
and performance to an original Product or part and warranted for the remainder of the original warranty period (or such
longer period as may be required by applicable law).
Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product in lieu of repair or
replacement. If the Product or component is no longer available, replacement may be made with a similar product of equal
or greater value, at Company’s sole discretion. This is your sole and exclusive remedy for breach of this limited warranty.
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR,
REPLACE OR REFUND, AT THE COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER
THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL
NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN
CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE. Incidental damages include but are not limited to
such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing
or replacing other property which was damaged if the Product does not work properly.
THE COMPANY SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER YOU, FOR ANY OTHER
OBLIGATIONS OR LIABILITIES, INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING
OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT
LIABILITY, WITH RESPECT TO THE PRODUCT OR THE COMPANY’S ACTS OR OMISSIONS OR OTHERWISE.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which
vary from jurisdiction to jurisdiction. The disclaimers, exclusions, and limitations of liability under this warranty will not apply
to the extent prohibited by applicable law.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and
does not include the cost of field service travel and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty
will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product,
except for those incurred with the Company’s prior written permission.
How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or
telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and part
identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty service, you
must present evidence of the original purchase date. If you cannot provide a copy of the original written limited warranty,
then the terms of the Company’s most current written limited warranty for your particular product will control. The most
current limited written warranties for the Company’s products can be found at www.venmar.ca.
Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville, Québec, Canada J2C 7W9 www.venmar.ca 1-800-567-3855
Download PDF
Similar pages