Disclaimer - FixYourDLP.com

Disclaimer
This user manual is provided as a free service by FixYourDLP.com. FixYourDLP is in no way responsible
for the content of this manual, nor do we guarantee its accuracy. FixYourDLP does not make any claim
of copyright and all copyrights remain the property of their respective owners.
About FixYourDLP.com
FixYourDLP.com (http://www.fixyourdlp.com) is the World’s #1 resource for media product news,
reviews, do-it-yourself guides, and manuals.
Informational Blog: http://www.fixyourdlp.com
Video Guides: http://www.fixyourdlp.com/guides
User Forums: http://www.fixyourdlp.com/forum
FixYourDLP’s Fight Against Counterfeit Lamps:
http://www.fixyourdlp.com/counterfeits
Sponsors:
RecycleYourLamp.org – Free lamp recycling services for used lamps:
http://www.recycleyourlamp.org
Lamp Research - The trusted 3rd party lamp research company:
http://www.lampresearch.com
Discount-Merchant.com – The worlds largest lamp distributor:
http://www.discount-merchant.com
Sponsored by DM
User's Guide
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Notations Used in This Guide
• Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• General information indications
Attention
q
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
s
Indicates a page where detailed information regarding a topic can be found.
g
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendix".s p.74
Procedure
Indicates operating methods and the order of operations.
The procedure indicated should be carried out in the order of the numbered steps.
[ (Name) ]
Indicates the name of the buttons on the Remote Control or the Control panel.
Example: [Esc] button
"(Menu Name)"
Brightness (bolded)
Indicates Configuration Menu items.
Example:
Select "Brightness" from the Image menu.
Image menu - Brightness
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Contents
3
Notations Used in This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction
Part Names and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front/Top. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to Video Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 6
. 7
. 8
. 8
. 9
11
Connecting and Removing USB Devices. . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting USB devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing USB devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Ending a Slideshow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a slideshow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending a slideshow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slideshow Basic Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotating Images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting Image Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting an image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sequentially projecting all image files in a folder (Slideshow). . . . . . . . . .
Image File Display Setting and Slideshow Operation Setting. . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
23
24
24
24
24
24
25
26
26
27
28
Configuration Menu
Useful Functions
Using the Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the Projected Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Automatically Detect Input Signal and Change the Projected Image (Source Search)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switch to the target image by Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . 14
Functions for Enhancing Projection. . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting the Projection Quality (Selecting Color Mode). . . . . . . . . . . . . . .
Setting the Auto Iris. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hiding the Image and Sound Temporarily (A/V Mute). . . . . . . . . . . . . . . . .
Freezing the Image (Freeze). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Aspect Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Aspect for video equipment images. . . . . . . . . . . . . . . . .
Changing the aspect for computer images. . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
15
16
16
17
17
17
18
19
Security Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
List of Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Image Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Info Menu (Display Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Specifications of Files that can be Projected in a Slideshow. . . . . . . . . . . . . . . . . . 23
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
31
32
33
35
37
38
Troubleshooting
Using the Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Problem Solving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Reading the Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restricting Operation (Control Panel Lock). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
t Indicator is lit or flashing red. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anti-Theft Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
oM
Indicator
isD
litA
orC
flashing
orange.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORm
L
A
PSAN
CE
S
S
O
RI
E
S. . . . . . . . . . . . . . . . . . . . . .
Installing the wire lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
When the Indicators Provide No Help. . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting JPEG Images in a Slideshow. . . . . . . . . . . . . . . . . . . . . . . 23
.
.
.
.
.
.
.
.
.
.
Problems relating to images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems when projection starts. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
41
42
43
44
45
49
Contents
4
Other problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Appendix
Component video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Composite video/S-video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Input signal from the HDMI input port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Installation Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Projector General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Cleaning the Projector's Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Cleaning the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Cleaning the Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Replacing Consumables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Replacing the Remote Control Batteries. . . . . . . . . . . . . . . . . . . . . . .
Replacing the Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp replacement period. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the lamp hours. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air filter replacement period. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the air filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
55
56
56
56
59
59
59
59
General Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
General Notice:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Optional Accessories and Consumables. . . . . . . . . . . . . . . . . . . . . . . 61
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Consumables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Saving a User's Logo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Screen Size and Projection Distance. . . . . . . . . . . . . . . . . . . . . . . . . . 64
Monitoring and Controlling the Projector Using a Computer
(ESC/VP21 Commands). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Command List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Communications protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
ROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Supported Monitor Displays. . . . . . T
. .H
.E
. .T
.R
.U
. .S
.T
.E
.D
. . .S
.O
.U
.R
. .C
.E
. .F
.O
. .R
.P
67
Supported Monitor Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Computer signals (analog RGB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Introduction
This chapter explains the part names and connection with video equipment.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Part Names and Functions
6
Name
Front/Top
Function
C A/V mute slide knob
Slide the knob to open and close the A/V mute slide.
D A/V mute slide
Close when not using the projector to protect the lens.
By closing during projection you can hide the image and
the sound (A/V Mute).s p.16
E Foot adjust lever
Pull the Foot adjust lever to extend and retract the Front
adjustable foot.s Quick Start Guide
F Front adjustable foot
Extend and adjust the position of the projected image
when the projector is placed on a surface such as a desk.
s Quick Start Guide
G Remote Receiver
Receives signals from the remote control.s Quick Start
Guide
H Air filter
(Air intake vent)
Takes in air to cool the projector internally. If dust
collects here it can cause the internal temperature to
rise, and this can lead to problems with operation and
shorten the optical engine's service life. Be sure to clean
the Air filter regularly. s p.54, p.59
I Air filter cover
Open and close when replacing the air filter.s p.59
J Speaker
Name
Function
A Lamp cover
Open this cover when replacing the projector's Lamp.
s p.56
B Air exhaust vent
Exhaust vent for air used to cool the projector internally.
K Security slot
The Security slot is compatible with the Microsaver
Security System manufactured by Kensington.s p.22
L Zoom ring
Adjusts the image size.s Quick Start Guide
M Focus ring
Adjusts the image focus.s Quick Start Guide
N Control panel
s p.8
Caution
Do not place objects that may become warped or
HET
R
US
T
E
D
S
O
UAir
RC
EF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
otherwiseT
affected
by
heat
near
the
exhaust
vent and do not put your face or hands near the
vent while projection is in progress.
Part Names and Functions
7
Name
Rear
Name
Function
G USB indicator
The following explains the status of USB devices
connected to USB(TypeA) port.
OFF: USB device is not connected
Orange Light ON: USB device is connected
Green Light ON: USB device is operating
Red Light ON: Error
H USB(TypeA) port
Connects a USB storage device or a digital camera, and
projects JPEG images using Slideshow.
I USB(TypeB) port
When controlling the projector from a computer,
connect it to the computer with a commercially
available USB cable. This port is for control use and
should not normally be used.s p.66
J S-Video input port
For S-video signals from video sources.
K Audio-L/R port
Inputs audio from the audio out port on the other
equipment.s Quick Start Guide
Function
A Remote Receiver
Receives signals from the remote control.s Quick Start
Guide
B Power inlet
Connects to the power cable.s Quick Start Guide
C Video Input Port
For composite video signals from video sources.
D Lamp Cover Fixing
Screw
Screw to fix the Lamp cover in place.s p.56
E HDMI input port
Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with HDCPg.
F Computer input port
For video signals from a computer and component
video signals from other video sources.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Part Names and Functions
8
Name
Base
C Security cable
installation point
Function
Pass a commercially available wire lock through here
and lock it in place. s p.22
Control Panel
Name
Name
A [t] button
Turns the projector power on or off.s Quick Start Guide
B Status indicators
The color of the indicators and whether they are flashing
or lit indicate the status of the projector. s p.41
C [Source Search]
button
Changes to the next input source that is connected to
the projector and is sending an image.s p.13
Function
A Ceiling mount fixing
points
(three points)
Attach the optional Ceiling mount here when
suspending the projector from a ceiling. s p.52,
p.61
B Rear foot
When setup on a desk, turn to extend and retract to
adjust the horizontal tilt.s Quick Start Guide
Function
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Part Names and Functions
Name
9
Function
D [Enter] button
If pressed during projection of computer signal images,
it automatically adjusts the Tracking, Sync., and
Position to project the optimum image. When a
Configuration Menu or a Help screen is displayed, it
accepts and enters the current selection and moves to
the next level.
E [w][v] buttons
Corrects Keystone distortion. s Quick Start Guide
However, when projecting in Slideshow, the buttons
only have the [ ][ ] functions. If pressed when a
Configuration Menu or a Help screen is displayed, these
buttons select menu items and setting values.s p.30
F [Help] button
Displays and closes the Help screen which shows you
how to deal with problems if they occur.s p.40
G [Esc] button
Stops the current function. If pressed when a
Configuration menu is displayed, it moves to the
previous menu level. sp.30
H [a][b] buttons
Adjusts the volume. s Quick Start Guide
However, when projecting in Slideshow, the buttons
only have the [ ][ ] functions. If pressed when a
Configuration Menu or a Help screen is displayed, these
buttons select menu items and setting values.s p.30
I [Menu] button
Displays and closes the Configuration Menu.s p.30
Remote Control
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Part Names and Functions
Name
10
Function
A [t] button
Turns the projector power On or Off.s Quick Start
Guide
B [Computer] button
Changes to images from the Computer input port.
s p.14
C [Video] button
Each time the button is pressed, the image cycles
through Video, S-Video, and HDMI input ports.
s p.14
D [USB] button
Changes to the Slideshow image.s p.14
E [A/V Mute] button
Turns the video and audio on or off.s p.16
F [Aspect] button
The Aspect Ratio changes each time the button is pressed.
s p.17
G [Auto] button
If pressed during projection of computer signal images,
it automatically adjusts the Tracking, Sync., and
Position to project the optimum image.
H [Menu] button
Displays and closes the Configuration Menu.s p.30
I [
[
][
][
]
] button
Name
Function
O [User] button
Press to assign a frequently used item from the four
available Configuration Menu items. By pressing the
button the assigned menu item selection/adjustment
screen is displayed, allowing you to make one-touch
settings/adjustments. Power Consumption is assigned
as the default setting.s p.33
P [Freeze] button
Images are paused or unpaused.s p.17
Q [Search] button
Changes to the next input source that is connected to
the projector and is sending an image.s p.13
R Remote control
light-emitting area
Outputs remote control signals.
When a Configuration Menu or Help screen is
displayed, it selects menu items and setting values.
s p.30
J [Enter] button
When a Configuration Menu or a Help screen is
displayed, it accepts and enters the current selection and
moves to the next level. s p.30
K [Esc] button
Stops the current function. If pressed when a
configuration menu is displayed, it moves to the
previous level. s p.30
L [Volume] buttons (a)
(b)
(a) Decreases the Volume.
(b) Increases the Volume.
s Quick Start Guide
M [Help] button
Displays and closes the Help screen which shows you
how to deal with
problems
ifT
they
p.40
T
H
ET
RUS
E
Doccur.s
S
OURC
EF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
N [Color Mode] button
Each time the button is pressed, the Color Mode changes.
s p.15
Part Names and Functions
11
Connecting to Video Equipment
Attention
Port names may vary depending on the equipment being connected.
Video equipment (VHS VCR, DVD player, game console, etc.)
Computer
• Power off the equipment before connecting. Connecting while it is powered
on may cause malfunctions to occur.
• When connecting, check the cable's connector shape with the shape of the
port. Inserting a connector with a different orientation or shape by force
may cause malfunctions to occur or may damage the equipment.
L-Audio-R
S-Video
Video
Component
output
HDMI
Mini D-Sub
15-pin
Audio
Component
video cable
(commercially
-available)
RCA video
Audio cable S-Video cable
cable
(commercially- (commercially- (commercially
available)
available)
-available)
HDMI cable
(commerciallyavailable)
component
adapter
(accessory)
Computer
cable
(optionnal)
Audio cable
(commerciallyavailable)
q
• Use an HDMI cable that conforms to HDMI standard.
• Depending on the equipment you are connecting to, the
connecter shape may be specific to that equipment. In such a
case, use the cable that was supplied with the equipment or is
available as an optional accessory for that equipment.
• The cable used to connect to the projector will vary according to
the video signal output from the video equipment. Some video
equipment can output several different types of video signals. In
general, the following are video signals in the order of image
quality, from best quality to lesser quality.
Component video > S-video > Composite video
Check your video equipment's documentation to see which video
signals it can output. Composite video may also be simply called
"Video out".
For information on optional accessories, see s "Optional Accessories
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
and Consumables" p.61.
Useful Functions
This chapter explains useful tips for projection, and the Security functions.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Changing the Projected Image
You can change the projected image in the following two ways.
• Changing by Source Search
The projector automatically detects signals being input from connected
equipment, and the image being input from the equipment is projected.
• Changing directly to the target image
You can use the Remote Control buttons to change to the target
input port.
13
Procedure
When your video equipment is connected, start playback before
beginning this operation.
Using the Remote Control
Using the Control panel
Automatically Detect Input Signal and Change
the Projected Image (Source Search)
You can project the target image quickly as input ports with no image
signal being input are ignored when you change by pressing the [Source
Search] button.
When two or more pieces of equipment are connected, press the
[Source Search] button until the target image is projected.
q
A
B
C
D
E
The following screen showing the status of image signals is
displayed when only the image that the projector is currently
displaying is available, or when no image signal can be found. You
can select the input port where the equipment you want to use is
connected. If no operation is performed after about 10 seconds, the
screen closes.
Computer
S-Video
Video
HDMI
USB
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Changing the Projected Image
Switch to the target image by Remote Control
You can change directly to the target image by pressing the following
buttons on the Remote Control.
Remote Control
A Changes to images from the Computer input port.
B Each time the button is pressed, the image cycles through Video, S-Video,
and HDMI input ports.
C Changes to the Slideshow image.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
14
Functions for Enhancing Projection
Selecting the Projection Quality (Selecting Color
Mode)
15
q
The color mode can also be set using Color Mode in the Image
menu from the Configuration Menu.s p.31
You can easily obtain the optimum image quality simply by selecting
the setting that best corresponds to your surroundings when projecting.
The brightness of the image varies depending on the mode selected.
Mode
Application
Dynamic
Ideal for use in a bright room.
Living Room
Ideal for using the projector in a room with closed
curtains.
Theatre
Ideal for watching films in a dark room. Gives images
a natural tone.
Game
Ideal for playing games that involve speed in a bright
room.
Procedure
Remote Control
Each time you press the button, the Color Mode name is displayed on
the screen and the Color Mode changes.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
If you press the button while the Color Mode name is displayed on the
screen, it changes to the next Color Mode.
Functions for Enhancing Projection
16
Setting the Auto Iris
By automatically setting the luminance according to the brightness of
the displayed image, it lets you enjoy deep and rich images.
Procedure
A Press the [Menu] button and select Image - Auto Iris from
Procedure
the Configuration Menu.s "Using the Configuration Menu"
p.30
Using the Remote Control
Remote Control
Body
Using the Control panel
B Select On.
Each time you press the button, or open/close the lens cover A/V Mute
turns on or off.
The setting is stored for each Color Mode.
• If you use this function when projecting moving images, the
images and sound continue to be played back by the source, and
Press the [Menu] button to close the Configuration Menu.
you cannot return to the point where A/V Mute was activated.
• When activated from the remote control, you can choose to
display Black, Blue, or Logo as the A/V Mute display using the
Extended - Display - A/V Mute setting from the Configuration
Hiding the Image and Sound Temporarily (A/V
menu.s p.35
Mute)
• When the A/V mute slide is closed for approximately 30
minutes, Lens Cover Timer activates and the power is
Use this to temporarily turn off the screen image.
automatically turned off. If you do not want Lens Cover Timer
to activate, change the Lens Cover Timer setting to Off from
Operation
in
the
Extended
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPS
ANDAC
CE
S
S
O
RI
E
S menu.s p.35
C
q
Functions for Enhancing Projection
Freezing the Image (Freeze)
When Freeze is activated on moving images, the frozen image continues
to project on the screen, so you can project a moving image one frame
at a time like a still photo. Also, you can perform operations such as
changing between files during presentations from a computer without
projecting any images if the Freeze function is activated beforehand.
17
Changing the Aspect Ratio
Change the Aspect Ratiog when video equipment is connected so that
images that have been recorded in digital video or onto DVDs can be
viewed in 16:9 wide-screen format. Change the Aspect Ratio when
projecting computer images at full size.
The changing methods and the types of Aspect ratio are as follows.
Procedure
Changing methods
Remote Control
Procedure
Remote Control
Each time you press the button, Freeze turns on or off.
q
• Audio does not stop.
• The image source continues to play back the moving images
even while the screen is frozen, and so it is not possible to
resume projection from the point where it was paused.
• If the [Freeze] button is pressed while the Configuration Menu
or a Help screen is displayed, the menu or Help screen being
displayed is cleared.
Each time you press the button, the Aspect name is displayed on the
screen and the Aspect changes.
If you press the button while the Aspect name is displayed on the
screen, it changes to the next Aspect Mode.
q
The aspect ratio can also be set using Aspect in the Signal menu
from the Configuration Menu.s p.32
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Functions for Enhancing Projection
Changing the Aspect for video equipment images
Each time the button is pressed, it changes in the order Normal or
Auto, 16:9, Full, Zoom, and Native.
A
B
C
D
E
Normal or Auto
16:9
Full
Zoom
Native
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
18
Functions for Enhancing Projection
19
Changing the aspect for computer images
You can change the Aspect as follows. This projector offers WXGA 1280x800 resolution (Aspect Ratio 16:10). When projecting onto 16:9 screens, set the
Aspect to 16:9.
Set Values
Operation
Projection example
Normal
Projects to the full projection size retaining the Aspect of
the input image.
When a 1024x768 signal is input
Auto
Displayed only when the source is
HDMI.
Projects in an appropriate aspect based on information
from the input signal.
16:9
Projects to the full projection size at an Aspect of 16:9.
When a 1024x768 signal is input
Full
Project at full size.
When a 1024x768 signal is input
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Functions for Enhancing Projection
Set Values
20
Operation
Projection example
Zoom
Projects the input image at the lateral direction aspect size When a 1024x768 signal is input
as it is. Parts that extend beyond the projection size are not
projected.
Native
When an 800x600 signal is input
Projects at the resolution of the input image size to the
center of the screen. This is ideal for projecting clear images.
If the image resolution exceeds 1280x800, the edges of the
image are not projected.
q
When an 1400x1050 signal is input
If parts of the image are missing, set Wide or Normal in Resolution from the Configuration Menu depending on the size of the computer panel.
s p.32
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Security Functions
21
The projector has the following enhanced security functions.
• Control Panel Lock
You can prevent people changing the settings on the projector without
permission.s p.21
• Anti-Theft Lock
The projector is equipped with various types of anti-theft security devices.
s p.22
Procedure
A During projection, press the [Menu] button and select
Settings - Control Panel Lock from the Configuration Menu.
s "Using the Configuration Menu" p.30
Using the Remote Control
Using the Control panel
Restricting Operation (Control Panel Lock)
Perform one of the following to lock the operation buttons on the
Control panel.
The projector can still be operated using the Remote Control.
• Full Lock
All of the buttons on the Control panel are locked. You cannot
perform any operations from the Control panel, including turning the
power on or off.
• Partial Lock
All of the buttons on the Control panel, except for the [t] button,
are locked.
B Select either Full Lock or Partial Lock.
C Select Yes when the confirmation message is displayed.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AThe
MPS
ANDACCE
S
S
ORI
E
S
Control panel buttons are locked according to the setting you
chose.
Security Functions
q
22
You can release the Control panel lock by one of the following
two methods.
• From the Remote Control, select Off in Settings - Control Panel
Lock from the Configuration Menu.
• Press and hold down the [Enter] button on the Control panel
for about seven seconds, a message is displayed and the lock is
released.
Anti-Theft Lock
As the projector is often setup on ceiling mounts and left in rooms
unattended, the projector includes the following security devices to
prevent someone from taking the projector.
• Security slot
The Security slot is compatible with the Microsaver Security System
manufactured by Kensington. You can find details about the
Microsaver Security System on the Kensington homepage http://
www.Kensington.com/.
• Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Projecting JPEG Images in a Slideshow
In Slideshow, you can connect a USB storage device or a digital camera
to the projector, and directly project the image files saved on the device.
q
23
Example: Connecting a digital camera
It may not be possible to use USB storage devices with security
functions.
Specifications of Files that can be Projected in a
Slideshow
Type
File Type (extension)
Still image .jpg
q
Remarks
The following cannot be projected.
• CMYK color mode format
• Progressive format
• Resolutions exceeding 8176x6144
• Files with extension ".jpeg"
Due to the characteristics of JPEG files, images with
high compression ratio may not be projected clearly.
• Use media that have been formatted on Windows, as some file
systems may not be supported by the projector.
• Format the media to FAT16 or FAT32.
A To digital camera USB port
B USB cable
C To USB(Type A) port
Attention
• If you use a USB hub, the Slideshow will not function correctly. Devices
Connecting and Removing USB Devices
such as digital cameras and USB storage devices should be connected to
the projector directly.
• When connecting and using a USB-compatible hard disk, make sure you
Connecting USB devices
connect the AC adaptor supplied with the hard disk.
• Connect a digital camera or hard disk to the projector using a USB cable
Connect the USB device containing the
image
files
to S
be
played
back
in
T
HE
T
RUS
T
E
D
OU
RCEF
ORP
ROJ
E
CT
OR
L
AMPSANDACCE
S
S
ORI
E
S
provided with, or specified for use with the device.
Slideshow to the projector's USB(TypeA) port. When connecting a
• Use a USB cable less than 3 m in length. If the cable exceeds 3 m,
digital camera, connect it to the projector using a USB cable provided
Slideshow may not function correctly.
with, or specified for use with your digital camera.
Projecting JPEG Images in a Slideshow
Removing USB devices
After finishing projecting, remove the USB device from the projector's
USB(TypeA) port.
For digital cameras, hard disks, and so on, turn off the power to the
device and then remove.
24
q
• You can insert a memory card into a USB card reader and
connect it to the projector. However, it may not be possible to
use some commercially available USB card readers with the
projector.
• If the following screen (Select drive screen) appears, select the
drive you want to use by pressing the [
][
] buttons, then
press the Enter button.
Starting and Ending a Slideshow
Starting a slideshow
Procedure
A Switch the projected image to USB.s p.13
B Connect the USB storage device or the digital camera to the
projector.s p.23
The Slideshow starts and displays the file list screen.
Ending a slideshow
• To display the Select drive screen, set the cursor to Select drive
on the top of the file list screen and press the Enter button.
• Up to four drives can be recognized at one time by the projector.
Slideshow Basic Operations
Procedure
To end a Slideshow, remove the connected USB device from the projector.
s "Removing USB devices" p.24
This section explains the procedure for playing back and projecting
images in Slideshow.
Although the following steps are explained based on the Remote
Control, you can perform the same operations from the projector's
Control panel.
Procedure
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
A Press the [
][
][ ][ ] buttons to set the cursor
on the file or folder you want to operate.
Projecting JPEG Images in a Slideshow
25
B Press the [Enter] button.
The selected image is displayed.
If a folder was selected, the files in the folder are displayed. On
the screen showing the contents of the folder, if you select Back
to Top and press the [Enter] button, the screen prior to opening
the folder is displayed again.
Rotating Images
A JPEG image projected using the Slideshow function can be rotated in
90 degree increments. JPEG images played back in a Slideshow can also
be rotated.
A Cursor
• JPEG files are displayed as thumbnails (small images of the files'
contents).
• It may not be possible for some JPEG files to be displayed as
thumbnails. In this case, an icon of a file is displayed.
Use the following procedure to rotate a JPEG image or JPEG images.
Procedure
A Start the Slideshow and project a single JPEG image or run
a slideshow using more than one JPEG images.
Projecting a single JPEG images p.26
Running a Slideshows p.27
B Once a JPEG image is projected or a slideshow is started,
q
If all of the files and folders cannot fit in the current screen, set
the cursor to Next page on the bottom of the screen, then press
the [Enter] button.
press the [
] button or the [
To return to the previous screen, set the cursor to Previous page
on the top of the screen, then press the [Enter] button.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
] button.
Projecting JPEG Images in a Slideshow
26
Although the following steps are explained based on the Remote
Control, you can perform the same operations from the projector's
Control panel.
Projecting an image
Procedure
A Start a Slideshow.s p.24
The file list screen appears.
B Press the [
][
][ ][ ] buttons to set the cursor
on the image file you want to project.
Projecting Image Files
The Slideshow offers you two ways to project image files contained in a
USB storage device or a digital camera.
• Projecting the selected single image file
This function projects the single image file you selected.
• Sequentially projecting image files in a folder (Slideshow)
This function sequentially plays back image files (runs a slideshow) in
the selected folder.s p.27
A Image file
Attention
C
Do not disconnect the USB storage device while it is being accessed. A
Press the [Enter] button.
problem may occur in the Slideshow. T
image
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AThe
MPS
ANDisAprojected.
CCE
S
S
ORI
E
S
Projecting JPEG Images in a Slideshow
27
Procedure
A Start a Slideshow.s p.24
The file list screen appears.
B Press the [
][
][ ][ ] buttons to set the cursor
to the folder for which you want to run the Slideshow, then
press the [Enter] button.
C Select "Slideshow" on the bottom of the file list screen and
D If you press the [Esc] button, the file list screen is displayed
again.
Sequentially projecting all image files in a folder (Slideshow)
You can project images files in a folder sequentially, one at a time.
This function is called Slideshow. Use the following procedure to run a
Slideshow.
q
To change files automatically in the Slideshow, set the Screen
switching time to any value other than No in the Option screen.
This is set to No by default.s p.28
press the [Enter] button.
The Slideshow starts, projecting the image files in the folder
automatically in sequence, one at a time.
Once the Slideshow reaches the end, the screen automatically
returns to the file list screen. If Continuous Play is set to On in
the Option screen, once the Slideshow reaches the end, it is
repeated from the beginning.s p.27
While projecting a Slideshow, you can go to previous/next screen
or cancel playback.
q
If Screen switching time is set to No in the Option screen, the
files will not change automatically after you start the playback of
the Slideshow Press the [Enter] button on the Remote Control to
project the next file.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Projecting JPEG Images in a Slideshow
Image File Display Setting and Slideshow
Operation Setting
You can set the display order of the files and the operation of the
Slideshow in the Option screen.
28
Continuous
Play
Sets whether or not to repeat the Slideshow.
Screen switching time
Sets the display time for each file in a Slideshow playback.
Set to any value from No(0) to 60 seconds. When set to
No, automatic paging is disabled.
Effect
Sets the screen effect to be used when changing slides.
C Press the [
Procedure
A Press the [
][
][ ][ ] buttons to set the cursor
to the folder for which you want to set the display
requirements, then press the [Esc] button. Select "Option"
from the displayed sub menu and press the [Enter] button.
][
][ ][
on "OK", then press [Enter].
The settings are applied.
If you do not want to apply the settings, set the cursor to Cancel
and press the [Enter] button.
B Set each item in the following Option screen.
Set the cursor to the setting value of the item you want to
change, and press the [Enter] button to make it active.
The following table shows the details of each item.
Display order
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Sets the display order of the files. Select from Name order
and Date order, in ascending order.
] buttons to set the cursor
Configuration Menu
This chapter explains how to use the Configuration Menu and its functions.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Using the Configuration Menu
Selecting from the top menu
30
Selecting from the sub menu
Changing the selected item
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Exit
List of Functions
31
Image Menu
Items that can be set vary depending on the image signal and Source currently being projected as shown in the following screen shots. Setting details
are saved for each image signal.
Component Videog/Composite videog/S-Video g
Analog RGB/Digital RGB/USB
Sub Menu
Function
Color Mode
You can select the quality of the image to suit your surroundings.s p.15
Brightness
You can adjust the image Brightness.
Contrast g
You can adjust the difference between light and shade in the images.
Color Saturation
You can adjust the Color Saturation for the images.
Tint
(Adjustment is only possible when NTSC signals are being input if you use composite video/S-Video.)
You can adjust the image Tint.
Sharpness
You can adjust the image sharpness.
Color Temp.
You can adjust the overall tint of the image. When High is selected the image becomes tinged with blue, when Low is selected the image becomes
tinged with red.
Color Adjustment
Red, Green, Blue: You can adjust the saturation of each color individually.
Auto Iris
Set whether or not (On/Off) to adjust to the optimum light status for images being projected.s p.16
Reset
You can reset all adjustment values for the Image menu functions to their default settings. To return all menu items to their default settings, see
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
s p.38 T
List of Functions
32
Signal Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for
each image signal.
Analog RGB
*
Digital RGB/RGB Video/
Component Video *g
Component Videog
Composite videog/S-Video g
When inputting signal from the HDMI input port
Sub Menu
Function
Auto Setup
You can select whether or not (On/Off) Auto Setup automatically adjusts the image to the optimum state when the Input Signal changes.
Resolution
When set to Auto, the resolution of the input signal is automatically identified. If the images cannot be projected correctly when set to Auto, such
as when some of the image is missing, adjust to Wide depending on the connected computer for wide screens, or set to Normal for 4:3 or 5:4 screens.
Tracking g
You can adjust computer images when vertical stripes appear in the images.
Sync. g
You can adjust computer images when flickering, fuzziness, or interference appear in the images.
Position
You can adjust the display Position up, down, left, and right when a part of the image is missing so that the whole image is projected.
Progressive
(When component video or RGB video signal is input, this setting can only be adjusted when 480i/576i signals are being input. This cannot be set
when a digital RGB signal is input.)
Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement.
On: Interlaceg (i) signal is converted to Progressiveg (p). Applies to still images.
HDMI Video Range
(This cannot be set when a digital RGB signal is input)
When theT
projector's
HDMI
input
port
isF
connected
toJ
aC
DVD
player
and
soA
on,
theA
projector's
video
range is set according to the DVD player's
H
ET
RUS
T
E
DS
OUR
CE
ORPRO
E
T
OR
L
AM
PS
ND
CCE
S
S
O
RI
E
S
video range setting.
List of Functions
33
Sub Menu
Function
Input Signal
You can select input signal from Computer input port.
If set to Auto the input signal is set automatically according to the connected equipment.
If colors do not appear correctly when set to Auto, select the appropriate signal according to the connected equipment.
Video Signal
You can select input signal from Video input port. If set to Auto, video signals are recognized automatically. If interference appears in the image or
a problem occurs such as no image is being projected when set to Auto, select the appropriate signal according to the connected equipment.
Aspect
You can set the Aspect Ratiog for projected images.s p.17
Reset
You can reset all adjustment values on the Signal menu to their default settings, except for Input Signal.
To return all menu items to their default settings, see s p.38
Settings Menu
Sub Menu
Function
Keystone
You can correct keystone distortion in the vertical directions.s Quick Start Guide
Auto Keystone
Turn On to perform Auto Keystone.
(Auto Keystone is only executed when Front is selected from the Extended - Projection menu.)
Control Panel Lock
You can use this to restrict operation of the projector's Control panel.s p.21
Power Consumption
You can set the Lamp brightness to one of two settings.
T
H
T
R
US
T
E
DS
O
URCEF
OR
ROJ
E
CT
O
L
AM
PSANimages
DACC
S
OR
I
E
Sor onto a small screen. When ECO is
Select ECO
ifE
the
images
being
projected
are
tooP
bright
such
asR
when
projecting
inE
aS
dark
room
selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and fan rotation noise during projection is
reduced. Electrical consumption: about 19% decrease, lamp life: about 1.3 times longer
List of Functions
Sub Menu
34
Function
Volume
You can adjust the Volume. Setting details are saved for each source.
User Button
You can select the item assigned from the Configuration Menu with the Remote Control's [User] button. By pressing the [User] button the
assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments. You can assign one of the
following items to the [User] button.
Power Consumption, Info, Progressive, Resolution
Reset
You can reset all adjustment values on the Settings menu to their default settings, except for User Button.
To return all menu items to their default settings, see s p.38
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
List of Functions
35
Extended Menu
Sub Menu
Function
Display
You can make settings related to the projector's display.
Messages: When set to Off, the following items will not be displayed. The name of the current selection when changing the Source,
Color Mode or Aspect; a message when no image signal is input; warnings such as the High Temp Warning.
Display Background: You can set the screen status for when no image signal is available to Black, Blue, or Logo.
Startup Screen: You can set whether or not (On/Off) the Startup Screen (the image projected when starting the projector) is displayed.
A/V Mute: You can set the screen displayed during A/V Mute as Black, Blue, or Logo.
User's Logo
You can change the User's Logo that is displayed as a background during Display Background, A/V Mute, and so on.s p.62
Projection
You can set from the following according to the way the projector is setup.s p.52
Front, Front/Ceiling, Rear, Rear/Ceiling
You can change the setting as follows by pressing down the [A/V Mute] button on the Remote Control for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
List of Functions
36
Sub Menu
Function
Operation
Direct Power On: You can set whether or not (On/Off) to enable Direct Power On.
When it is set to On and the power cable is plugged in, be aware that the projector turns on automatically in case such as a power
outage is restored.
Sleep Mode: When set to On, this automatically stops projection when no image signal is being input and no operations are carried
out.
Sleep Mode Timer: When Sleep Mode is set to On, you can set the time before the projector automatically turns off within a range
of one to 30 minutes.
Lens Cover Timer: When set to On, this turns off the power automatically 30 minutes after the A/V mute slide is closed. Lens
Cover Timer is set to On at the time of purchase.
High Altitude Mode: Set to On when using the projector above an altitude of 1500 m.
Standby Mode
Set to Communication On when the projector's status is to be monitored and controlled from the computer via USB communication,
even when the projector is in standby mode.
s p.66
Link 21L
Set to On when the projector's status is to be monitored and controlled from the computer via USB communication.s p.66
Language
You can set the language for message displays.
Reset
You can reset Display and Operation* from the Extended menu to their default settings.
To return all menu items to their default settings, see s p.38
* Except for High Altitude Mode.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
List of Functions
37
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the image
signal and Source currently being projected as shown in the following screen shots.
Analog RGB/Digital RGB/
RGB Video/Component Video g
Composite video g/S-Video g
Sub Menu
Function
time*.
Lamp Hours
You can display the cumulative Lamp operating
When it reaches the lamp warning time, the characters are displayed in yellow.
Source
You can display the Source name for the connected equipment currently being projected.
Input Signal
You can display the content of Input Signal set in the Signal menu according to the Source.
Resolution
You can display the input resolution.
Video Signal
You can display the content of Video Signal set in the Signal menu.
Refresh Rateg
You can display the Refresh Rate.
Sync Info
You can display the image signal information.
This information may be needed if service is required.
Status
This is information about errors that have occurred on the projector.
This information may be needed if service is required.
* The cumulative use time is displayed as
"0H"
for
the
first
10
hours.
10R
hours
above
isA
displayed
asD"10H",
"11H",
and
T
H
ET
R
US
T
E
D
S
O
UR
CEF
O
PROand
J
E
CT
ORL
MPSAN
ACCE
S
S
ORI
E
Sso on.
USB
List of Functions
38
Reset Menu
Sub Menu
Function
Reset All
You can reset all items in the Configuration Menu to their default settings.
The following items are not reset to their defaults: Input Signal, User's Logo, Lamp Hours, and Language.
Reset Lamp Hours
You can clear the cumulative Lamp Hours use time, and return it to "0H". Reset when you replace the Lamp.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Troubleshooting
This chapter explains how to identify problems and what to do if a problem is found.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Using the Help
40
If a problem occurs with the projector, the Help screen is displayed to
assist you by pressing the [Help] button. You can solve problems by
answering the questions.
C Confirm the selection.
Using the Remote Control
Using the Control panel
Procedure
A Press the [Help] button.
The Help screen is displayed.
Using the Remote Control
Using the Control panel
Questions and solutions are displayed as shown on the screen below.
Press the [Help] button to exit Help.
B Select a menu item.
q
Using the Remote Control
If the Help screen does not provide a solution to the problem,
refer to "Problem Solving" p.41.
Using the Control panel
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Problem Solving
41
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help".s p.44
Reading the Indicators
The projector is provided with the following three indicators that indicate the operating status of the projector.
A Indicates the operating status.
Standby condition
When the [t] button is pressed in this condition, projection starts.
Cooling down
All buttons are disabled while the indicator is flashing.
Warming up
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
The [t] button is disabled during warm-up.
Projecting
B Indicates the internal temperature status.
status.
C Indicates the projection lamp T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally.
Problem Solving
42
Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period, but this is not a fault.
t Indicator is lit or flashing red
: Lit
Status
Cause
: Flashing
: Off
Remedy or Status
Internal Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address
provided in the Support and Service Guide.s Epson Projector Contact List
Fan Error
Sensor Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address
provided in the Support and Service Guide.s Epson Projector Contact List
High Temp Error
(overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector
switches to standby mode, so check the following two points.
• Check that the air filter and Air exhaust vent are clear, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it. s p.54, p.59
If the error continues after checking the points above, stop using the projector, disconnect the power cable from the electrical
outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.s Epson Projector Contact
List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.s p.35
Lamp Error
Lamp Failure
Check the following two points.
• Take out the lamp and check if it is cracked.s p.56
• Clean the air filter.s p.54
If it is not cracked: Re-fit the Lamp and turn on the power.
If the error continues: Replace the Lamp with a new lamp and turn on the power.
If the error continues: Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local
dealer or the nearest address provided in the Support and Service Guide.s Epson Projector Contact List
If it is cracked:Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself, be
careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced).s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.s p.35
Auto Iris Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address
T
HET
R
US
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
provided in the Support and Service Guide.s Epson Projector Contact List
Power Err. (Ballast)
Problem Solving
43
m o Indicator is lit or flashing orange
: Lit
Status
q
Cause
: Flashing
: Off
: Varies according to the projector status
Remedy or Status
High Temp Warning
(This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
• Check that the air filter and Air exhaust vent are clear, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it. s p.54, p.59
Replace Lamp
Replace it with a new Lamp.s p.56
If you continue to use the Lamp after the replacement period has passed, the possibility that the lamp may explode increases.
Replace it with a new Lamp as soon as possible.
• If the projector is not operating properly, even though the indicators are all showing normal, refer to "When the Indicators Provide No Help" p.44.
• If the error is not indicated in this table, stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or
the nearest address provided in the Support and Service Guide.s Epson Projector Contact List
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Problem Solving
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer
a solution, refer to the pages given for each problem.
44
Other problems
• "No sound can be heard or the sound is faint" s p.49
• "The Remote Control does not work" s p.49
• "I want to change the language for messages and menus" s p.50
Problems relating to images
• "No images appear" s p.45
Projection does not start, the projection area is completely black, the
projection area is completely blue, and so on.
• "Moving images are not displayed" s p.45
Moving images being projected from a computer appear black and
nothing is projected.
• "Projection stops automatically" s p.45
• "The message "Not Supported." is displayed." s p.46
• "The message "No Signal." is displayed." s p.46
• "Images are fuzzy or out of focus" s p.46
• "Interference or distortion appear in images" s p.47
Problems such as interference, distortion, or black & white checked
patterns appear.
• "The image is truncated (large) or small, or the aspect is not suitable" s p.47
Only part of the image is displayed, or the height and width ratios of the
image are not correct, and so on.
• "Image colors are not right" s p.48
The whole image appears purplish or greenish, images are black & white,
colors appear dull, and so on... (Computer monitors and LCD screens
have different color reproduction performance, so that the colors
projected by the projector and the colors appearing on the monitor may
not necessarily match, but this is not a sign of a problem.)
• "Images appear dark" s p.48
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Problems when projection starts T
• "The projector does not turn on" s p.49
Problem Solving
45
Problems relating to images
No images appear
Check
Remedy
Did you press the [t] button?
Press the [t] button to turn the power on.
Are the indicators switched off?
The power cable is not connected correctly or power is not being supplied normally.
Connect the projector's power cable correctly.s Quick Start Guide
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active?
Press the [A/V Mute] button on the Remote Control to cancel A/V Mute.s p.16
Is the A/V mute slide closed?
Open the A/V mute slide.s p.6
Are the Configuration Menu settings correct?
Reset all of the settings. s Reset Menu - Reset All p.38
Is the projected image completely black?
Some input images, such as screen savers, may be completely black.
Only when projecting computer images
Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.32
Is the image signal format setting correct?
Only when projecting images from a video source
Moving images are not displayed
Check
Remedy
Is the computer's image signal being output to the LCD and the
monitor?
Change the image signal to external output only. s Check your computer's documentation.
Only when projecting images from a laptop computer or a computer
with a built-in LCD screen
Projection stops automatically
Check
Is Sleep Mode set to On?
Remedy
T
HET
RUS
T
E
DS
OUR
CE
F
O
RPR
OJ
E
CT
OR
L
AM
PIfSyou
AN
Dnot
AC
CE
S
S
RI
E
S Mode, change the setting to Off.
Press
the
[t]
button
to
turn
the
power
on.
do
want
toO
use
Sleep
s Extended Menu - Operation - Sleep Mode p.35
Problem Solving
46
The message "Not Supported." is displayed.
Check
Remedy
Is the image signal format setting correct?
Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.32
Only when projecting images from a video source
Do the image signal Resolution and the Refresh Rate correspond
to the mode?
Refer to the computer's documentation for how to change the image signal Resolution and the Refresh Rate output
from the computer.s "Supported Monitor Displays" p.67
Only when projecting computer images
The message "No Signal." is displayed.
Check
Remedy
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.s Quick Start Guide
Is the correct input port selected?
Change the image by pressing the [Source Search] button on the Remote Control or the Control panel.s p.13
Is the power for the computer or video source turned on?
Turn the power on for the equipment.
Are the image signals being output to the projector?
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to
change the output to an external destination as well as the computer's own monitor. For some computer models,
when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
s Computer's documentation, under a title such as "External output" or "Connecting an external monitor". If the
connection is made while the power of the projector or computer is already turned on, the function [Fn] key that
changes the computer's image signal to external output may not work. Turn the power for the computer and the
projector off and then back on again.
Only when projecting images from a laptop computer or a computer
with a built-in LCD screen
Images are fuzzy or out of focus
Check
Remedy
Is the focus adjusted correctly?
Turn the focus ring to adjust the Focus.s Quick Start Guide
Is the projector at the correct distance?
Is it projecting outside of the recommended projection distance range?
Setup within the recommended range.s p.64
Is the Keystone adjustment value too large?
Lower
the
toT
reduce
the
of
correction.s
T
HET
RUS
T
E
DS
OURC
Eprojection
F
ORPRangle
OJ
E
C
O
RL
A
Mamount
PSAN
Dkeystone
ACCE
S
S
ORI
E
S Quick Start Guide
Problem Solving
47
Check
Remedy
Has condensation formed on the lens?
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient
temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to
appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens,
turn the projector off and wait for the condensation to disappear.
Interference or distortion appear in images
Check
Remedy
Is the image signal format setting correct?
Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.32
Only when projecting images from a video source
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.s Quick Start Guide
Is an extension cable being used?
If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector
to check if the cables you are using may be causing the problem.
Is the correct resolution selected?
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.67 s Computer documentation
Only when projecting computer images
Are the "Sync.g" and "Trackingg" settings adjusted correctly?
Only when projecting computer images
Press the [Auto] button on the Remote Control or the [Enter] button on the Control panel to perform automatic
adjustment. If the images are not adjusted correctly after using automatic adjustment, you can make the adjustments
using Sync. and Tracking from the Configuration Menu. s Signal Menu - Tracking, Sync. p.32
The image is truncated (large) or small, or the aspect is not suitable
Check
Remedy
Is a wide panel computer image being projected?
Change the setting according to the signal for the connected equipment. s Signal Menu - Resolution p.32
Only when projecting computer images
Is Position adjusted correctly?
Press the [Auto] button on the Remote Control or the [Enter] button on the Control panel to perform automatic
adjustment of the computer image being projected. If the images are not adjusted correctly after using automatic
adjustment, you can make the adjustments using Position from the Configuration Menu.
Apart from computer image signals, you can adjust other signals while projecting by adjusting Position from the
Configuration
Menu.
s
Signal
Menu
- Position
p.32
T
HET
RUS
T
E
DS
OURCEF
OR
PRO
J
E
CT
OR
L
AM
PSAND
ACCE
S
S
ORI
E
S
Problem Solving
48
Check
Remedy
Is the computer set for dual display?
If dual display is activated in the "Display Properties" of the computer's Control Panel, only about half of the image
on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display
setting. s Computer video driver documentation
Only when projecting computer images
Is the correct resolution selected?
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.67 s Computer documentation
Only when projecting computer images
Image colors are not right
Check
Remedy
Do the input signal settings match the signals from the connected
device?
Change the following settings according to the signal for the connected equipment.
When image is from a device connected to the Computer input port s Signal Menu - Input Signal p.32
When image is from a device connected to the Video or S-Video input port s Signal Menu - Video Signal p.32
Is the image Brightness adjusted correctly?
Adjust the Brightness setting from the Configuration Menu. s Image menu - Brightness p.31
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.s Quick Start Guide
Is Contrastg adjusted correctly?
Adjust the Contrast setting from the Configuration Menu. s Image Menu - Contrast p.31
Is the Color Adjustment set correctly?
Adjust the Color Adjustment setting from the Configuration Menu. s Image Menu - Color Adjustment p.31
Are the Color Saturation and Tint adjusted correctly?
Adjust the Color Saturation and Tint settings from the Configuration Menu. s Image Menu - Color Saturation,
Tint p.31
Only when projecting images from a video source
Images appear dark
Check
Remedy
Are the image brightness and luminance adjusted correctly?
Adjust the Brightness and Brightness Control settings from the Configuration Menu.
s Image menu - Brightness p.31 s Settings menu - Brightness Control p.33
Is Contrastg adjusted correctly?
Adjust the Contrast setting from the Configuration Menu.
s Image Menu - Contrast p.31
Is it time to replace the Lamp?
When the time approaches to replace the Lamp , the images become darker and the color quality becomes poorer.
T
HET
RUS
T
E
DS
OURC
EF
ORPR
OJ
E
Cthe
T
OR
L
Awith
MPS
AN
DACCE
S
S
ORI
E
S
When
this
happens,
replace
Lamp
a new
lamp.s
p.56
Problem Solving
49
Problems when projection starts
The projector does not turn on
Check
Remedy
Did you press the [t] button?
Press the [t] button to turn the power on.
Are the indicators switched off?
The power cable is not connected correctly or power is not being supplied normally.
Disconnect and then reconnect the power cable.s Quick Start Guide
Check that your electrical outlet or power source is functioning correctly.
Do the indicators turn on and off when the power cable is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If
this does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and
contact your local dealer or the nearest address provided in the Support and Service Guide.s Epson Projector
Contact List
Is the Control Panel Lock set to Full Lock?
Press the [t] button on the Remote Control. If you do not want to use Control Panel Lock, change the setting to
Off. s Settings Menu - Control Panel Lock p.21
Other problems
No sound can be heard or the sound is faint
Check
Remedy
Is the audio source connected correctly?
Disconnect the cable from the Audio port, and then reconnect the cable.
Is the volume adjusted to the minimum setting?
Adjust the volume so that sound can be heard. s p.33 s Quick Start Guide
Is A/V Mute active?
Press the [A/V Mute] button on the Remote Control to cancel A/V Mute.s p.16
Is the audio cable's specification "No resistance"?
When using a commercially available audio cable, make sure it is labeled "No resistance".
The Remote Control does not work
Check
Remedy
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDA
CCE
S
S
ORI
E
S
Is the Remote Control light-emitting area pointing towards the
Remote Receiver on the projector when it is operated?
Point the remote control towards the Remote Receiver.
Operating ranges Quick Start Guide
Problem Solving
50
Check
Remedy
Is the remote control too far from the projector?
The operating range for the remote control is about 6 m.s Quick Start Guide
Is direct sunlight or strong light from fluorescent lamps shining
onto the Remote Receiver?
Set the projector up in a location where strong light does not shine onto the Remote Receiver.
Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.s p.55
I want to change the language for messages and menus
Check
Change the Language setting.
Remedy
Adjust the "Language" setting from the Configuration Menu.s p.35
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Appendix
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Installation Methods
52
The projector supports the following four different projection methods.
Install according to the conditions of the installation location.
Warning
• Suspend the projector from the
ceiling and project images from
in front of the screen. (Front/
Ceiling projection)
• Suspend the projector from the
ceiling and project images from
behind a translucent screen.
(Rear/Ceiling projection)
• A special method of installation is required when suspending the projector
from a ceiling (ceiling mount). If it is not installed correctly, it could fall
causing an accident and injury.
• If you use adhesives on the Ceiling mount fixing points to prevent the
screws from loosening, or if you use things such as lubricants or oils on
the projector, the projector case may crack causing it to fall from its
ceiling mount. This could cause serious injury to anyone under the ceiling
mount and could damage the projector.
When installing or adjusting the Ceiling mount, do not use adhesives to
prevent the screws from loosening and do not use oils or lubricants and so
on.
Attention
q
• An optional Ceiling mount is required when suspending the
projector from a ceiling.
s p.61
• You can change the setting as follows by pressing down the [A/
V Mute] button on the Remote Control for about five seconds.
FrontWFront/Ceiling
Set Rear or Rear/Ceiling from the Configuration Menu.s p.35
Do not use the projector on its side. This may cause malfunctions to occur.
• Project images from in front of
the screen. (Front projection)
• Project images from behind a
translucent screen. (Rear projection)
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Cleaning
53
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe
the lens.
Attention
Turn off the projector's power before cleaning.
Warning
Cleaning the Projector's Surface
Do not use sprays that contain flammable gas to remove dust and lint from
the lens. The projector may catch fire due to the high internal temperature
of the lamp.
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water
containing a small amount of neutral detergent, and then firmly wring
the cloth dry before using it to wipe the projector's surface.
Attention
Do not rub the lens with harsh materials or subject the lens to shocks, as it
can easily become damaged.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the
projector's surface. The quality of the case may change or become discolored.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Cleaning
54
Cleaning the Air Filter
Clean the air filter and the Air intake vent when the following message
is displayed.
"The projector is overheating. Make sure nothing is blocking the air
vent, and clean or replace the air filter."
Attention
• If dust collects on the air filter it can cause the internal temperature of
the projector to rise, and this can lead to problems with operation and
shorten the optical engine's service life. Clean the air filter immediately
when the message is displayed.
• Do not rinse the air filter in water. Do not use detergents or solvents.
q
• If a message is frequently displayed, even after cleaning, it is
time to replace the air filter. Replace it with a new air filter.
s p.59
HET
RUS
T
E
Dat
S
O
URC
EF
O
RPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
• It is recommended that you T
clean
these
parts
least
once
every
three months. Clean them more often than this if using the
projector in a particularly dusty environment.
Replacing Consumables
55
This section explains how to replace the Remote Control batteries, the
Lamp, and the air filter.
B Replace the old batteries with new batteries.
Replacing the Remote Control Batteries
If delays in the responsiveness of the Remote Control occur or if it
does not operate after it has been used for some time, it probably
means that the batteries are becoming flat. When this happens, replace
them with new batteries. Have two AA size manganese or alkaline
batteries ready. You cannot use other batteries except for the AA size
manganese or alkaline.
Caution
Attention
Make sure you read the Safety Instructions before handling the batteries. s
Safety Instructions
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
C Replace the battery cover.
Procedure
Press the battery compartment cover until it clicks into place.
A Remove the battery cover.
While pushing the battery compartment cover catch, lift the cover
up.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Replacing Consumables
Replacing the Lamp
Lamp replacement period
It is time to replace the Lamp when:
• The message "Replace the lamp." is displayed at the lower left of the
projection screen when you start projecting.
56
Attention
• The lamp replacement message is set to appear after the following time
periods in order to maintain the initial brightness and quality of the
projected images.s p.33
When Power Consumption is set to Normal: About 3900 hours
When Power Consumption is set to ECO: About 4900 hours
• If you continue to use the Lamp after the replacement period has passed,
the possibility that the lamp may explode increases. When the Lamp
replacement message appears, replace the Lamp with a new one as soon as
possible, even if it is still working.
• Do not repeatedly turn off the power and immediately back on. Turning
the power on and off frequently may shorten the lamp's operating life.
• Depending on the characteristics of the Lamp and the way it has been
• The Lamp indicator flashes orange.
used, the lamp may become darker or stop working before the lamp
warning message appears. You should always have a spare lamp unit ready
in case it is needed.
How to replace the lamp
The Lamp can be replaced even when the projector is suspended from
a ceiling.
Warning
• When replacing the Lamp because it has stopped illuminating, there is a
possibility that the Lamp may be broken. If replacing the Lamp of a
projector which has been installed on the ceiling, you should always
assume that the Lamp is broken, and you should stand to the side of the
Lamp cover, not underneath it. Remove the Lamp cover gently.
• The projected image gets darker or starts to deteriorate.
• Never disassemble or remodel the Lamp. If a remodeled or reassembled
Lamp is installed into the projector and used, it could cause a fire, electric
shock,
or
anN
accident.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMP
SA
DACCE
S
S
ORI
E
S
Replacing Consumables
57
Caution
Wait until the Lamp has cooled down sufficiently before removing the Lamp
cover. If the lamp is still hot, burns or other injuries may result. It takes
about one hour after the power has been turned off for the Lamp to be cool
enough.
Procedure
A After you turn off the projector's power and the
confirmation buzzer beeps twice, disconnect the power cable.
B Wait until the Lamp has cooled down, then remove the
C Loosen the two Lamp fixing screws.
Lamp cover.
Loosen the Lamp cover fixing screw with the screwdriver supplied
with the new lamp unit or a + head screwdriver. Then slide the
Lamp cover straight forward and lift it to remove.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Replacing Consumables
58
D Take out the old Lamp by pulling the handle.
If the Lamp is cracked, replace it with a new lamp, or contact
your local dealer for further advice. s Epson Projector Contact
List
E Install the new Lamp.
Insert the new Lamp along the guide rail in the correct direction
so that it fits in place securely, and tighten the two screws.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Replacing Consumables
59
F Replace the Lamp cover.
Replacing the Air Filter
Air filter replacement period
It is time to replace the air filter when:
• There is a tear in the air filter.
• The message is displayed even though the air filter has been cleaned.
How to replace the air filter
Attention
• Make sure you install the Lamp securely.
If the Lamp cover is removed,
the power turns off automatically as a safety precaution. If the Lamp or
the Lamp cover is not installed correctly, the power does not turn on.
• This product includes a lamp component that contains mercury (Hg).
Please consult your local regulations regarding disposal or recycling. Do not
dispose of it with normal waste.
The air filter can be replaced even when the projector is suspended
from a ceiling.
Procedure
A After you turn off the projector's power and the
confirmation buzzer beeps twice, disconnect the power cable.
B Open the air filter cover.
Resetting the lamp hours
The projector records how long the lamp is turned on and a message
and indicator notify you when it is time to replace the lamp. After
replacing the Lamp, make sure you reset the Lamp Hours from the
Configuration Menu.s p.38
q
Only reset the Lamp Hours after the Lamp has been replaced.
Otherwise the Lamp replacement period is not indicated correctly.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Replacing Consumables
60
C Remove the air filter.
Grip the air filter cover tab and pull it straight out.
q
Dispose of used air filters properly in accordance with your local
regulations.
Material of the frame part: ABS
Material of the filter part: Polyurethane foam
D Install the new air filter.
Slide the air filter from the outside and press in until it firmly
clicks into place.
E Close the air filter cover.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Optional Accessories and Consumables
The following optional accessories and consumables are available. Please
purchase these products as and when needed. The following list of
optional accessories and consumables is current as of: 2009.07. Details
of accessories are subject to change without notice and availability may
vary depending on the country of purchase.
61
Document Camera ELPDC06
Connect to the projector through a computer, and use it for projecting such
documents as books, OHP documents, and slides.
Ceiling pipe (450 mm) * ELPFP13
Ceiling pipe (700 mm) * ELPFP14
Use when installing the projector on a high ceiling.
Optional accessories
60" portable screen ELPSC07
80" portable screen ELPSC08
100" screen ELPSC10
Portable roll-type screens (Aspect Ratiog 4:3)
70" portable screen
80" portable screen
90" portable screen
ELPSC23
ELPSC24
ELPSC25
Ceiling mount* ELPMB23
Use when installing the projector on a ceiling.
*
A special method of installation is required to suspend the projector from
a ceiling. Contact your dealer or the nearest address provided in the
Support and Service Guide if you want to use this installation method.
s Epson Projector Contact List
Consumables
Portable roll-type screens (Aspect Ratiog 16:10)
Lamp unit ELPLP54
50" portable screen ELPSC06
Use as a replacement for used Lamps.
A compact screen that can be carried easily. (Aspect Ratio 4:3)
Air filter ELPAF25
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use as a replacement for used air filters.
This is the same as the computer cable supplied with the projector.
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use one of these longer cables if the computer cable supplied with the
projector is too short.
Component video cable ELPKC19
H
ET
R
S
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
(3 m - for mini D-Sub 15-pin/RCAT
male
^U
3)
Use to connect a component videog source.
Saving a User's Logo
62
You can save the image that is currently being projected as a User's Logo.
q
Once a User's Logo has been saved, the logo cannot be returned
to the factory default.
• If User's Logo is selected when Keystone, Aspect, or Progressive
are being performed, the function currently being performed is
cancelled.
C When "Choose this image as the User's Logo?" is displayed,
select "Yes".
Procedure
A Project the image you want to use as the User's Logo, and
then press the [Menu] button.
Using the Remote Control
q
Using the Control panel
q
When you press the [Enter] button on the Remote Control or the
Control panel, the screen size may change according to the signal
as it changes to the resolution of the image signal.
D Move the box to select the part of the image to use as the
User's Logo.
B Select Extended - User's Logo from the Configuration Menu.
s "Using the Configuration Menu" p.30
Check the buttons you can use and the operations they perform
in the guide under the menu.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Saving a User's Logo
63
G When the message Save this image as the User's Logo? is
displayed, select Yes.
The image is saved. After the image has been saved, the message
Completed.is displayed.
Using the Remote Control
q
Using the Control panel
q
• When a User's Logo is saved, the previous User's Logo is erased.
• Saving the user's logo may take approximately 15 seconds. Do
not use the projector or any connected equipment while it is
saving, otherwise malfunctions may occur.
You can save at 400 ^ 300 dots in size.
E When Select this image? is displayed,
select Yes.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
F Select the zoom factor from the zoom setting screen.
Screen Size and Projection Distance
64
Units: cm
A
16:9 Screen size
A Projection distance
B Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C Center of lens
Units: cm
A
4:3 Screen size
Minimum (Wide) to Maximum
(Tele)
B
40"
81x61
126 - 152
9
50"
100x76
158 - 190
11
60"
120x91
190 - 229
13
80"
160x120
255 - 306
17
100"
200x150
319 - 383
22
120"
240x180
383 - 461
26
150"
300x230
480 - 577
33
200"
410x300
641 - 770
44
250"
500x380
802 - 963
48
280"
570x430
898 - 1079
61
Minimum (Wide) to Maximum
(Tele)
B
40"
89x50
114 - 137
5
50"
110x62
143 - 172
6
60"
130x75
172 - 208
8
80"
180x100
231 - 278
10
100"
220x120
289 - 348
13
120"
270x150
348 - 418
15
150"
330x190
435 - 523
19
200"
440x250
582 - 699
26
250"
550x310
728 - 874
32
310"
690x390
903 - 1084
40
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Screen Size and Projection Distance
65
Units: cm
A
16:10 Screen size
Minimum (Wide) to Maximum
(Tele)
B
40"
86x54
111 - 134
8
50"
110x67
139 - 168
10
60"
130x81
168 - 202
12
80"
170x110
225 - 270
15
100"
220x130
281 - 338
19
120"
260x160
338 - 407
23
150"
320x200
424 - 509
29
200"
430x270
566 - 680
38
250"
540x340
708 - 850
48
320"
690x430
907 - 1089
62
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Monitoring and Controlling the Projector Using a Computer (ESC/VP21 Commands)
You can monitor and control the projector from a computer, via USB.
This is done by connecting the projector and the computer with a USB
cable, and entering communication commands (ESC/VP21 commands).
If the command being processed terminates abnormally, an error
message is output and a ‘:’ is returned.
Item
Power ON/OFF
Before You Begin
To monitor and control the projector with ESC/VP21 commands, the
following preparations must be carried out.
Signal selection
Procedure
A Install the USB communication driver (EPSON USB-COM
Driver) to your computer. For information about the EPSON
USB-COM Driver, contact your local dealer or the nearest
address provided in the Support and Service Guide.s Epson
Projector Contact List
B Set Extended - Link 21L to On from the projector's
Configuration menu.
C Connect the computer's USB port to the projector's
USB(TypeB) port with a USB cable.
From second time on, start from step two.
Command List
When the power ON command is transmitted to the projector, the
power turns on and it enters warm-up mode. When the projector's
power has turned on, a colon ‘:’ (3Ah) is returned.
A/V Mute On/Off
A/V Mute selection
Command
On
PWR ON
Off
PWR OFF
Computer
Auto
SOURCE 1F
RGB
SOURCE 11
HDMI
SOURCE 30
Video
SOURCE 41
S-Video
SOURCE 42
USB
SOURCE 52
On
MUTE ON
Off
MUTE OFF
Black
MSEL 00
Blue
MSEL 01
Logo
MSEL 02
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
Communications protocol
• Default baud rate setting: 9600bps (the speed during communication
complies with the USB 1.1 standard.)
• Data length: 8 bit
• Parity: None
• Stop-bit: 1 bit
• Flow control: None
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
When a command is input, the projector executes the command and
returns a ‘:’, and then accepts the next command.
66
Supported Monitor Displays
67
Supported Monitor Displays
Computer signals (analog RGB)
Units: dots
Signal
Refresh Rate
(Hz)
Resolution
VGAEGA
85
VGA
Aspect Mode
Normal
16:9
Full
Zoom
Native
640x350
1280x700
1280x720
1280x800
1280x700
640x350
60/72/75/85/iMac*1
640x480/640x360*2
1066x800
1280x720
1280x800
1280x800
640x480
SVGA
56/60/72/75/85/iMac*1
800x600/800x450*2
1066x800
1280x720
1280x800
1280x800
800x600
XGA
60/70/75/85/iMac*1
1024x768/1024x576*2
1066x800
1280x720
1280x800
1280x800
1024x768
60
1280x768
1280x768
1280x720
1280x800
1280x768
1280x768
60
1360x768
1280x722
1280x720
1280x800
1280x722
1280x768
60/75/85
1280x800
1280x800
1280x720
1280x800
1280x800
1280x800
WXGA+
60/75/85
1440x900
1280x800
1280x720
1280x800
1280x800
1280x800
WSXGA+*3
60
1680x1050
1280x800
1280x720
1280x800
1280x800
1280x800
70/75/85
1152x864
1066x800
1280x720
1280x800
1280x800
1152x800
60/75/85
1280x1024
1000x800
1280x720
1280x800
1280x800
1152x800
60/75/85
1280x960
1066x800
1280x720
1280x800
1280x800
1152x800
SXGA+
60/75/85
1400x1050
1066x800
1280x720
1280x800
1280x800
1280x800
UXGA
60
1600x1200
1066x800
1280x720
1280x800
1280x800
1280x800
MAC13”
67
640x480
1066x800
1280x720
1280x800
1280x800
640x480
MAC16”
75
832x624
1066x800
1280x720
1280x800
1280x800
832x624
75
1024x768
1066x800
1280x720
1280x800
1280x800
1024x768
60
1024x768
1066x800
1280x720
1280x800
1280x800
1024x768
WXGA
SXGA
MAC19”
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Supported Monitor Displays
68
Signal
Refresh Rate
(Hz)
Resolution
MAC21”
75
1152x870
Aspect Mode
Normal
16:9
Full
Zoom
Native
1059x800
1280x720
1280x800
1280x800
1152x800
*1 Connection is disabled if the equipment does not have a VGA output port.
*2 Letterbox signal
*3 Only compatible when Wide is selected as the Resolution from the Configuration Menu.
Even when signals other than those mentioned above are input, it is likely that the image can be projected. However, not all functions may be supported.
Component video
Units: dots
Aspect Mode
Refresh Rate
(Hz)
Resolution
Normal
16:9
Full
Zoom
Native
SDTV(480i)
60
720x480/720x360*
1066x800
1280x720
1280x800
1280x800
640x480
SDTV(576i)
50
720x576/720x432*
1066x800
1280x720
1280x800
1280x800
768x576
60
720x480/720x360*
1066x800
1280x720
1280x800
1280x800
640x480
SDTV(576p)
50
720x576/720x432*
1066x800
1280x720
1280x800
1280x800
768x576
HDTV(720p)
50/60
1280x720
1280x720
1280x720
1280x800
1280x720
1280x720
HDTV(1080i)
50/60
1920x1080
1280x720
1280x720
1280x800
1280x720
1280x800
Signal
SDTV(480p)
* Letterbox signal
Composite video/S-video
Units: dots
Signal
TV(NTSC)
TV(PAL,SECAM)
* Letterbox signal
Refresh Rate
(Hz)
Resolution
60
720x480/720x360*
Aspect Mode
Normal
16:9
Full
Zoom
Native
1066x800
1280x720
1280x800
1280x800
640x480
*
1066x800
1280x720
50 T
720x576/720x432
HET
RUS
T
E
DS
O
URCEF
ORP
ROJ
E
CT
O
RL
AMPSAN
DACCE
S
S
OR1280x800
I
E
S
1280x800
768x576
Supported Monitor Displays
69
Input signal from the HDMI input port
Units: dots
Signal
Refresh Rate
(Hz)
Resolution
VGA
60
SVGA
Aspect Mode
16:9
Full
Zoom
Native
640x480/640x360*
1280x720
1280x800
1280x800
640x480
60
800x600
1280x720
1280x800
1280x800
800x600
XGA
60
1024x768
1280x720
1280x800
1280x800
1024x768
WXGA
60
1280x800
1280x720
1280x800
1280x800
1280x800
60
1280x960
1280x720
1280x800
1280x800
1280x800
60
1280x1024
1280x720
1280x800
1280x800
1280x800
SXGA+
60
1400x1050
1280x800
1280x800
1280x800
1280x800
UXGA
60
1600x1200
1280x720
1280x800
1280x800
1280x800
SDTV(480i)
60
720x480/720x360*
1280x720
1280x800
1280x800
640x480
SDTV(480p)
60
720x480/720x360*
1280x720
1280x800
1280x800
640x480
SDTV(576i)
50
720x576/720x432*
1280x720
1280x800
1280x800
768x576
SDTV(576p)
50
720x576/720x432*
1280x720
1280x800
1280x800
768x576
HDTV(720p)
50/60
1280x720
1280x720
1280x800
1280x720
1280x720
HDTV(1080i)
50/60
1920x1080
1280x720
1280x800
1280x720
1280x800
HDTV(1080p)
50/60
1920x1080
1280x720
1280x800
1280x720
1280x800
SXGA
* Letterbox signal
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Specifications
70
Projector General Specifications
EH-TW450
Product name
295 (W) ^ 77 (H) ^ 228 (D) mm
Dimensions
0.59" Wide
Panel size
Polysilicon TFT active matrix
Display method
1,024,000 pixels
WXGA (1280 (W) ^ 800 (H) dots) ^ 3
Resolution
Focus adjustment
Manual
Zoom adjustment
Manual (1 to 1.2)
UHE lamp, 200 W Model No.: ELPLP54
Lamp
1 W monaural
Max. audio output
1
Speaker
100 to 240 V AC ±10%, 50/60 Hz 3.2 to 1.4 A
Power supply
Power
consumption
100 to 120 V area
Operating: 280 W
Standby power consumption (Communication On): 2.6 W
Standby power consumption (Communication Off): 0.3 W
200 to 240 V area
Operating: 265 W
Standby power consumption (Communication On): 3.9 W
Standby power consumption (Communication Off): 0.4 W
Operating altitude
Operating temperature
Storage temperature
Mass
Altitude 0 to 2,286 m
5 to +35˚C (No condensation)
-10 to +60˚C (No condensation)
Approx. 2.3kg
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Specifications
71
EH-TW450
Product name
Connectors
Computer
Input Port
1
Mini D-Sub15-pin (female) blue
Video input
port
1
RCA pin jack
S-Video
input port
1
Mini DIN 4-pin
Audio Port
1
RCA pin jack x 2 (L, R)
HDMI port
1
HDMI (Audio is only supported by PCM)
USB(TypeA)
Port *1
1
USB connector (Type A)
USB(TypeB)
Port *2
1
USB connector (Type B)
*1 Supports USB 1.1.
*2 Supports USB 2.0.
USB(TypeA) and USB(TypeB) ports are not guaranteed to operate all devices that support USB.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 30˚ it could be damaged and cause an accident.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Specifications
72
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B
digital device. Each product marketed, is identical to the representative
unit tested and found to be compliant with the standards. Records
maintained continue to reflect the equipment being produced can be
expected to be within the variation accepted, due to quantity production
and testing on a statistical basis as required by 47CFR 2.909. Operation
is subject to the following two conditions : (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Trade Name:
EPSON
Type of Product:
LCD Projector
Model:
H331C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of
the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the
user to obtain and use a shielded equipment interface cable with this
device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications
not expressly approved by the manufacturer could void the user's
authority to operate the equipment.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Appearance
A
B
73
Center of lens
Distance from center of lens to suspension bracket fixing point
Units: mm
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Glossary
74
This section explains easily terms that are used with the projector and difficult terms that are not explained in the text of this guide. For details, refer
to other commercially available publications.
Aspect Ratio
(Aspect Ratio)
The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The aspect ratio for
standard images is 4:3.
Component Video
A Video signal which has the luminance component and color component separated to provide better image quality.
Refers to images that consist of three independent signals: Y (luminance signal), Pb and Pr (color difference signals).
Composite video
Video signals that have the video brightness signals and color signals mixed together. The type of signals commonly used by household video
equipment (NTSC, PAL, and SECAM formats). The carrier signal Y (luminance signal) and chroma (color) signal that are contained in the color
bar are overlapped to form a single signal.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or
to make them appear softer. Adjusting this particular property of an image is called Contrast adjustment.
Dolby Digital
A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format that uses two speakers. Dolby Digital is a 6-channel
(5.1-channel) system which adds to this a center speaker, two rear speakers, and a sub-woofer.
HDCP
An abbreviation of High-bandwidth Digital Content Protection, which refers to a copyright protection technology that prevents illegal copying
by encrypting the digital signals sent and received via HDMI port. Because the HDMI input port on this projector supports HDCP, it can project
digital images protected by HDCP technology, However, if the HDCP standard changes, it may not be possible to project digital images
protected by the changed standard.
HDTV
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressiveg, i = Interlaceg)
• Screen Aspect Ratiog of 16:9
Interlace
A method of image scanning whereby the image data is divided into fine horizontal lines that are displayed in sequence starting from left to right
and then from top to bottom. The even-numbered lines and odd-numbered lines are displayed alternately.
Progressive
A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create a single image.
Refresh Rate
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be
scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh Rate
and is expressed in hertz (Hz).
SDTV
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTVg
High-Definition Television.
sRGB
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
computer
operating
systems
(OS)
and
the
Internet.
IfE
the
connected
anA
sRGB
mode,
set
both the projector and the connected signal
T
HE
T
RUS
T
E
DS
O
URC
EF
OR
PROJ
CT
ORL
AMsource
PSAhas
ND
CCE
S
S
ORI
E
S
source to sRGB.
SVGA
A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers.
Glossary
75
S-Video
A Video signal which has the luminance component and color component separated to provide better image quality.
Refers to images that consist of two independent signals: Y (luminance signal) and C (color signal).
SXGA
A type of video signal with a resolution of 1,280 (horizontal) ^ 1,024 (vertical) dots that is used by IBM PC/AT-compatible computers.
Sync.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are
not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is
called Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
Tracking
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are
not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is
not carried out correctly, wide vertical stripes appear in the signal.
VGA
A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers.
XGA
A type of video signal with a resolution of 1,024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
General Notes
76
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of
this product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated
as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
General Notice:
Windows Vista and the Windows logo are trademarks of the Microsoft group of
companies.
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corporation.
Macintosh, Mac, and iMac are trademarks of Apple Inc.
Windows, Windows NT, and PowerPoint are trademarks or registered trademarks of
Microsoft Corporation in the United States.
Dolby is a trademark of Dolby Laboratories.
HDMI and High-Definition Multimedia Interface are the trademarks or registered
trademarks of HDMI Licensing LLC.
©SEIKO EPSON CORPORATION 2009. All rights reserved.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Index
77
Control Panel Lock ............................... 21, 33
A
A/V Mute ...................................................... 16
Air exhaust vent ............................................. 6
Air filter replacement period ..................... 59
Air intake vent ................................................ 6
Angle of tilt ................................................... 71
Appearance ................................................... 73
Aspect ...................................................... 17, 33
Audio-L/R port .............................................. 7
Auto Iris ........................................................ 16
Auto Setup .................................................... 32
C
Keystone ........................................................ 33
D
Direct Power On ..........................................
Display ...........................................................
Display Background ....................................
Distance ........................................................
Dynamic ........................................................
36
35
35
64
15
E
ESC/VP21 ..................................................... 66
Extended Menu ............................................ 35
B
Brightness ..................................................... 31
Brightness Control ...................................... 33
K
F
Focus ring ....................................................... 6
Freeze ............................................................. 17
Front .............................................................. 35
Front adjustable foot ..................................... 6
Full Lock ....................................................... 21
L
Lamp Hours ..................................................
Lamp replacement period ..........................
Language .......................................................
Link 21 ...........................................................
37
56
36
36
M
Messages ....................................................... 35
Monitor Displays ......................................... 67
O
Operating temperature ...............................
Operation ......................................................
Optional accessories ....................................
Overheating ..................................................
70
36
61
42
Ceiling ........................................................... 35
Ceiling mount fixing points ......................... 8
Cleaning the Air filter and Air intake vent
P
H
.......................................................................... 54
Part Names and Functions ........................... 6
Cleaning the Projector's Surface ................ 53
HDMI input port ........................................... 7
Position ......................................................... 32
Color Adjustment ........................................ 31
HDMI Video Range .................................... 32
Power inlet ...................................................... 7
Color Mode ............................................ 15, 31
Help function ............................................... 40
Problem Solving ........................................... 41
Color Saturation .......................................... 31
High Altitude Mode .................................... 36
Progressive .................................................... 32
Computer input port ..................................... 7
How to replace the air filter ........................ 59
Projection ...................................................... 35
Configuration Menu ................................... 30
How to replace the lamp ............................. 56
Connecting and Removing USB Devices
R
.......................................................................... 23
I
Consumables ................................................
61
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Rear
................................................................
35
Image
Menu
.................................................
31
Contrast ........................................................ 31
Rear foot .......................................................... 8
Info Menu ..................................................... 37
Control Panel ................................................. 8
Rear screen .................................................... 52
Input Signal ............................................ 33, 37
Index
Refresh Rate .................................................. 37
Remote Control .............................................. 9
Remote Receiver ........................................ 6, 7
Replacing batteries ....................................... 55
Reset All ........................................................ 38
Reset Menu ................................................... 38
Resetting the lamp operating time ...... 38, 59
Resolution ..................................................... 37
78
U
USB(TypeA) port ........................................... 7
USB(TypeB) port ........................................... 7
User's Logo ................................................... 62
V
Video Input Port ............................................ 7
Video Signal ........................................... 33, 37
Volume .......................................................... 34
S
Screen size ..................................................... 64
Security slot .................................................... 6
Settings Menu ............................................... 33
Sharpness ...................................................... 31
Signal Menu .................................................. 32
Sleep Mode ................................................... 36
Slideshow ...................................................... 23
Source ............................................................ 37
Source Search ........................................... 8, 13
Specifications ................................................ 70
Standby Mode .............................................. 36
Startup Screen .............................................. 35
Storage temperature .................................... 70
Supported Monitor Displays ...................... 67
S-Video input port ......................................... 7
Sync Info ....................................................... 37
Sync. ............................................................... 32
W
Wide-screen projection .............................. 17
Z
Zoom ring ....................................................... 6
T
Theatre .......................................................... 15
T
HET
RUS
T
E
DS
OURCEF
ORPROJ
E
CT
ORL
AMPSANDACCE
S
S
ORI
E
S
Tint ................................................................
31
Tracking ........................................................ 32
Disclaimer
This user manual is provided as a free service by FixYourDLP.com. FixYourDLP is in no way responsible
for the content of this manual, nor do we guarantee its accuracy. FixYourDLP does not make any claim
of copyright and all copyrights remain the property of their respective owners.
About FixYourDLP.com
FixYourDLP.com (http://www.fixyourdlp.com) is the World’s #1 resource for media product news,
reviews, do-it-yourself guides, and manuals.
Informational Blog: http://www.fixyourdlp.com
Video Guides: http://www.fixyourdlp.com/guides
User Forums: http://www.fixyourdlp.com/forum
FixYourDLP’s Fight Against Counterfeit Lamps:
http://www.fixyourdlp.com/counterfeits
Sponsors:
RecycleYourLamp.org – Free lamp recycling services for used lamps:
http://www.recycleyourlamp.org
Lamp Research - The trusted 3rd party lamp research company:
http://www.lampresearch.com
Discount-Merchant.com – The worlds largest lamp distributor:
http://www.discount-merchant.com
Sponsored by DM
Download PDF
Similar pages