OWNER’S MANUAL LED TV* * LG LED TVs are LCD TVs with LED backlighting. Please read this manual carefully before operating your TV and retain it for future reference. 32LY750H 39LY750H 42LY750H 47LY750H 55LY750H 32LY760H 39LY760H 42LY760H 47LY760H 55LY760H *mfl68080312* www.lgsolutions.com P/NO : MFL68080312 (1408-REV04) 2 IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. ENGLISH TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. ••Do not allow the television to become wet. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. ••Clean only with a dry cloth. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION - TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. ••Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. ••Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged. NOTE The note helps you understand and use the product safely. Please read the note carefully before using the product. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. ••Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet (Can differ by country). ••Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil or pen, or make a scratch on it. IMPORTANT SAFETY INSTRUCTIONS ••Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. ••Only use attachments/accessories specified by the manufacturer. ••Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. ••Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. ••Do not stick metal objects or any other conductive material into the power cord. Do not touch the end of the power cord while it is plugged in. ••Keep the packing anti-moisture material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed by mistake, induce vomiting and go to the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. ••CAUTION concerning the Power Cord (Can differ by country): Check the specification page of this owner’s manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not move the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV. ••Warning - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning. ••Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit). ENGLISH ••Unplug this apparatus during lightning storms or when unused for long periods of time. 3 4 IMPORTANT SAFETY INSTRUCTIONS ••Grounding (Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Short-circuit Breaker Power Supply ENGLISH ••As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off. ••Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product. ••Outdoor Antenna Grounding (Can differ by country): If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70 Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Ground Clamp Electric Service Equipment Grounding Conductor (NEC Section 810-21) Ground Clamp NEC: National Electrical Code Power Service Grounding Electrode System (NEC Art 250, Part H) ••Cleaning When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners, or benzine. ••Moving Make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV. ••Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials while plugged. Do not install in excessively dusty places. ••If you smell smoke or other odors coming from the TV, unplug the power cord and contact an authorized service center. ••Keep the product away from direct sunlight. ••Never touch this apparatus or antenna during a lightning storm. ••When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV. ••Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen. ••DISCONNECTING THE DEVICE FROM THE MAIN POWER The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible. ••Batteries Store the accessories (battery, etc.) in a safe location out of the reach of children. ••This apparatus uses batteries. In your community there might be regulations that require you to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information. ••Do not dispose of batteries in a fire. ••Do not short circuit, disassemble, or allow the batteries to overheat. ••Do not use high voltage electrical equipment near the TV, (e.g. bug zapper). This may result in product malfunction. IMPORTANT SAFETY INSTRUCTIONS Preventing image burn or burn-in on your TV screen ••If a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is image burn or burn-in and not covered by the warranty. ••If the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen. ••Avoid displaying a fixed image on the TV screen for a long period of time to prevent image burn. ENGLISH ••Dot Defect The panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV. ••Generated Sound Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing A low level noise is generated from a highspeed switching circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product. ••Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall. ••Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot. This does not affect the performance of the product or cause defects in the product. ••If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal; there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. 5 6 IMPORTANT SAFETY INSTRUCTIONS FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ENGLISH NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. LG Recycling Policy LG Electronics offers a customized e-waste take-back and recycling service that meets local needs and requirements in the countries where e-waste regulations are in place, and also provides product and packaging take-back and recycling service voluntarily in some countries. LG Electronics evaluates products’ recyclability at the design step using LG’s recyclability evaluation tool, with the goal of improving recyclability where practicable. Through these activities, LG seeks to contribute to conserving natural resources and protecting the environment. For more information about the LG Recycling Policy, please visit our global site at http://www.lg.com/global/sustainability/environment/take-back-recycling . LICENSES / OPEN SOURCE SOFTWARE NOTICE 7 LICENSES Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS 2.0+Digital Out is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved. OPEN SOURCE SOFTWARE NOTICE To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to firstname.lastname@example.org. This offer is valid for three (3) years from the date on which you purchased the product. NOTE ••Image shown may differ from your TV. ••Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. ••The available menus and options may differ from the input source or product model that you are using. ••New features may be added to this TV in the future. ENGLISH ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that has passed rigorous testing to verify that it plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration. DivX Certified® to play DivX® video up to HD 1080p, including premium content. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license. Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274 8 TABLE OF CONTENTS TABLE OF CONTENTS ENGLISH 2 IMPORTANT SAFETY INSTRUCTIONS 7 LICENSES 7 OPEN SOURCE SOFTWARE NOTICE 8 TABLE OF CONTENTS 9 ASSEMBLING AND PREPARING 9 10 11 12 13 13 13 16 18 19 Unpacking Optional Extras Parts and Buttons - Using the Joystick Button Lifting and Moving the TV Setting Up the TV - Attaching the Stand - Mounting on a Table - Mounting on a Wall - Tidying Cables 20 MAKING CONNECTIONS 20 21 Connecting to an Antenna or Cable Other Connections 25 REMOTE CONTROL 27 MAINTENANCE 27 27 27 Cleaning your TV - Screen, Frame, Cabinet, and Stand - Power Cord 27 TROUBLESHOOTING 28 SPECIFICATIONS ASSEMBLING AND PREPARING 9 Unpacking ENGLISH ENG ENGLISH ENG ASSEMBLING AND PREPARING Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item. ENERGY AV MODE INPUT TV SAVING 1 2 3 4 5 6 7 8 9 0 FLASHBK LIST MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Owner’s Manual Power Cord Stand Base, Stand Body (For 32/39LY750H, 32/39LY760H) (For 42/47/55LY750H, 42/47/55LY760H) (For 42LY750H, 42LY760H) (For 47/55LY750H, 47/55LY760H) Stand Screws 6 EA, M4 x L20 Stand Screws 4 EA, M4 x L20 4 EA, M4 x L14 Wall Mount Spacers 6 EA Wall Mount Spacers 4 EA Screws for Stand Fixing 2 EA (For 39/42/47/55LY750H, 39/42/47/55LY760H) Cable Holder 1 EA Power Cord Holder and Screw 1 EA Torx Plus Star-Head Screw 2 EA Washers for Stand Fixing 2 EA Nuts for Stand Fixing 2 EA Rubber 2 EA ENGLISH Remote Control, Batteries (AAA) 10 ASSEMBLING AND PREPARING CAUTION ••Do not use any unapproved items to ensure the safety and product’s lifespan. ••Any damages or injuries by using unapproved items are not covered by the warranty. ••Some models appear to have a thin film on the screen. It is actually part of the screen; do not remove it. NOTE ••The items supplied with your product may vary depending upon the model. ••Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions. ••For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) width. ••Use an extension cable that supports USB 2.0 if the USB cable or USB memory device does not fit into your TV’s USB port. B A *A 10 mm (0.39 inches) *B 18 mm (0.7 inches) ENGLISH Optional Extras Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items. These devices only work with certain models. The model name or design may be changed manufacturer’s circumstances or policies. AN-MR300 (For LY750H series) AN-MR500 (For LY760H series) Magic Remote B A ASSEMBLING AND PREPARING 11 Parts and Buttons Screen Speakers Intelligent Sensor1 Remote Control Sensor Power Indicator Joystick Button2 NOTE ••You can set the power indicator light to on or off by selecting OPTION or General in the main menus. (Depending upon model) ENGLISH 1. Intelligent Sensor - Adjusts the image quality and brightness based on the surrounding environment. 2. Joystick Button is located below the screen of TV. 12 ASSEMBLING AND PREPARING Using the Joystick Button You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right. Basic functions Power On When the TV is turned off, place your finger on the joystick button and press it once and release it. Power Off When the TV is turned on, place your finger on the joystick button and press it once for a few seconds and release it. Volume Control If you place your finger over the joystick button and move it left or right, you can adjust the volume level you want. Channels Control If you place your finger over the joystick button and move it up or down, you can scrolls through the saved channels you want. NOTE ENGLISH ••With your finger over the joystick button, move it up, down, left or right, be careful not to press the joystick button. If you press the joystick button first, you can not adjust the volume level and/or scroll through saved channels. Adjusting the menu (For LY760H series) When the TV is turned on, press the joystick button one time. You can adjust the Menu items ( , , ) moving the joystick button left or right. TV Off Turn the power off. Close Clears on-screen displays and returns to TV viewing. Input List Changes the input source. ASSEMBLING AND PREPARING Lifting and Moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. CAUTION ••Avoid touching or applying pressure to the screen at all times, as this may result in damage to the screen. ••Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen. ••It is recommended to move the TV in the box or packing material that the TV originally came in. ••Before moving or lifting the TV, disconnect the power cord and all cables. Setting Up the TV Attaching the Stand CAUTION ••When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. NOTE yyMake sure to hold the stand when attaching it to the TV to prevent the stand or TV from falling. yyRemove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. yyThe cover will protect the opening from accumulating dust and dirt. When installing the wall mounting bracket, use the cover. ••Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area. ••Use at least two people to move a large TV. ••When transporting the TV by hand, hold the TV as shown in the following illustration. ••When transporting the TV, do not expose the TV to jolts or excessive vibration. ••When transporting the TV, keep the TV upright; never turn the TV on its side or tilt towards the left or right. Rubber ENGLISH ••When holding the TV, the screen should face away from you to avoid damage. 13 14 ASSEMBLING AND PREPARING (For 42/47/55LY750H, 42/47/55LY760H) 3 4 EA M4 x L14 1 4 EA M4 x L20 or 2 EA Stand Body Stand Base ENGLISH 2 2 EA Tighten the two of these four screws and the two Torx screws (provided as parts of the TV) to secure the TV. Tighten the two Torx screws with a Torx driver bit (not provided as parts of the TV). ASSEMBLING AND PREPARING (For 32/39LY750H, 32/39LY760H) 15 3 1 2 EA M4 x L20 4 EA M4 x L20 or 2 EA Stand Body Tighten the two Torx screws (provided as parts of the TV) with a Torx driver bit (not provided as parts of the TV). Stand Base ENGLISH 2 NOTE ••When you install the screws, make certain they are in the correct locations for the model you have. 16 ASSEMBLING AND PREPARING Mounting on a Table 1 Attaching the TV to a desk Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. (Depending upon model) The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. TYPE 1 10 cm (4 inches) 10 cm 10 cm m 10 c ENGLISH 2 Connect the power cord to a wall outlet. CAUTION ••Do not place the TV near or on sources of heat, as this may result in fire or other damage. 4-Screws (Not provided as parts of the product) Stand Adjusting the angle of the TV to suit view Swivel 20 degrees to the left or right and adjust the angle of the TV to suit your view. 20˚ CAUTION 20˚ ••When adjusting the angle of the TV, watch out for your fingers. - Personal injury may occur if hands or fingers are pinched. If the product is tilted too much, it may fall, causing damage or injury. Desk NOTE ••Screw: M5 x L (*L: Table depth + 8~10 mm) ex) Table depth: 15mm, Screw: M5 x 25 ASSEMBLING AND PREPARING TYPE 2 17 Securing the TV to a wall (optional) (Depending upon model) 2-Screws, 2-Washers, 2-Nuts (provided as parts of the product) 1 2 Mount the wall brackets with the bolts to Desk the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or cable. Make sure to keep the rope parallel to the flat surface. CAUTION ••Make sure that children do not climb on or hang on the TV. NOTE ••Use a platform or cabinet that is strong and large enough to support the TV securely. ••Brackets, bolts, and ropes, are optional. You can obtain additional accessories from your local dealer. ENGLISH Stand Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. - If there are bolts inserted at the eye-bolts position, remove the bolts first. 18 ASSEMBLING AND PREPARING Mounting on a Wall CAUTION An optional wall mount can be used with your LG Television. Consult with your local dealer for a wall mount that supports the VESA standard used by your TV model. Carefully attach the wall mount bracket at the rear of the TV. Install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount. Detailed instructions will be included with the wall mount. We recommend that you use an LG brand wall mount. When you do not use LG’s wall mount bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. ••Disconnect the power before moving or installing the TV. Otherwise electric shock may occur. ••If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel. When using a third-party wall mount, it is not covered by the warranty. ••Do not over tighten the screws as this may cause damage to the TV and void your warranty. ••Use the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. NOTE ENGLISH 10 cm (4 inches) 10 cm 10 cm 10 cm Make sure to use screws and wall mounts that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table. 32LY750H 32LY760H 39LY750H 39LY760H 42LY750H 42LY760H 47LY750H 47LY760H 55LY750H 55LY760H 200 x 200 400 x 400 Standard screw M6 M6 Number of screws 4 4 Model ••Use the screws that are listed in the VESA standard screw specifications. ••The wall mount kit includes an installation manual and necessary parts. ••The wall mount bracket is optional. You can obtain additional accessories from your local dealer. ••The length of screws may differ depending upon the wall mount. Make sure to use the proper length. ••For more information, refer to the manual supplied with the wall mount. ••When attaching a wall mounting bracket to the TV, insert the wall mount inner spacers into the TV wall mount holes to adjust the vertical angle of the TV. (For 42LY750H, 42LY760H) Wall Mount Spacers VESA (A x B) A B Wall mount bracket LSW240B (optional) MSW240 LSW440B MSW240 ••If it is difficult to connect cables (antenna, power, etc.) to the back of the TV, use the provided Wall Mount Spacers with the TV wall mount holes. (For 42LY750H and 42LY760H, use 6 spacers. For 47/55LY750H and 47/55LY760H, use 4 spacers.) ••Please contact your dealer or mount vendor for other wall mounting options. ASSEMBLING AND PREPARING 19 Tidying Cables For 32LY750H, 32LY760H 1 Gather and bind the cables with the cable holder. Cable Holder 1 Install the power cord holder and power cord. It will help prevent the power cable from being removed by accident. 2 Gather and bind the cables with the cable holder. Power Cord Holder and Screw Cable Holder ENGLISH For 39/42/47/55LY750H, 39/42/47/55LY760H 20 MAKING CONNECTIONS MAKING CONNECTIONS ••Image shown may differ from your TV. You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external device’s connection, refer to the manual provided with each device. NOTE ••If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information about recording, refer to the manual provided with the connected device. ••The external device connections shown may differ slightly from illustrations in this manual. ••Connect external devices to the TV regardless about the order of the TV port. ••If you connect a gaming device to the TV, use the cable supplied with the gaming device. ••Refer to the external equipment’s manual for operating instructions. ••Using a DVI to HDMI cable may cause compatibility issues. Connecting to an Antenna or Cable ENGLISH Connect an antenna, cable, or cable box to watch TV. The illustrations may differ from the actual items and an RF cable is optional. VHF Antenna UHF Antenna Antenna Coaxial (75Ω) (*Not provided) Terminal CAUTION ••Make sure not to bend the copper wire of the RF cable. Copper wire NOTE ••Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV. ••Use a signal splitter to use 2 TVs or more. ••DTV Audio Supported Codec: MPEG, Dolby Digital MAKING CONNECTIONS 21 Other Connections Connect your TV to external devices. For the best picture and audio quality, connect digital devices using an HDMI cable. Any separate cable is not provided. For LY750H series Router / Modem PC Digital Audio System USB OPTICAL AUDIO IN ETHERNET RJP CONTROL OUT OPTICAL DIGITAL AUDIO OUT ENGLISH AUX LAN USB IN 1 1 PTC SERVICE (SERVICE ONLY) LAN RJP RS-232C IN (SERVICE) ANTENNA / CABLE IN SPEAKER OUT LINE OUT L R VIDEO L/MONO -AUDIO - R AV IN/AUDIO IN(DVI) RESET UPDATE RED WHITE RED WHITE External Speaker YELLOW L GND YELLOW GND R M.P.I. M.P.I VIDEO L/MONO AUDIO R SI Box Blu-Ray / HD Cable Box / DVD / VCR 22 MAKING CONNECTIONS Blu-Ray / HD Cable Box / HD STB / DVD / PC AUDIO OUT HDMI DVI OUT RED WHITE AUX LAN OPTICAL DIGITAL AUDIO OUT USB IN 1 RJP RS-232C IN ENGLISH (SERVICE) ANTENNA / CABLE IN SPEAKER OUT LINE OUT L USB IN 3 LAN R VIDEO L/MONO -AUDIO - R AV IN/AUDIO IN(DVI) M.P.I. RESET UPDATE IN 2 (ARC) (SERVICE ONLY) USB IN 2 1 PTC SERVICE MAKING CONNECTIONS 23 For LY760H series Router / Modem PC Digital Audio System USB OPTICAL AUDIO IN ETHERNET RJP CONTROL OUT AUX LAN OPTICAL DIGITAL AUDIO OUT ENGLISH USB IN 1 1 PTC SERVICE LAN (SERVICE ONLY) RJP RS-232C IN (SERVICE) ANTENNA / CABLE IN SPEAKER OUT LINE OUT VIDEO/Y PB PR L/MONO AUDIO R PC AUDIO M.P.I. COMPONENT IN / AV IN RED RED WHITE YELLOW L WHITE YELLOW VIDEO PR RED PB RED WHITE RED BLUE Y WHITE RED BLUE External Speaker GREEN L GND GREEN GND R RESET UPDATE R AUDIO VIDEO L/MONO AUDIO R Blu-Ray / HD Cable Box / DVD / VCR M.P.I SI Box 24 MAKING CONNECTIONS Blu-Ray / HD Cable Box / HD STB / DVD / PC AUDIO OUT DVI OUT HDMI RED WHITE AUX LAN OPTICAL DIGITAL AUDIO OUT USB IN 1 RS-232C IN RJP ANTENNA / CABLE IN SPEAKER OUT LINE OUT USB MHL Cable VIDEO/Y PB PR L/MONO AUDIO R PC AUDIO COMPONENT IN / AV IN M.P.I. RESET UPDATE IN 2 (ARC) ENGLISH (SERVICE) IN 3 (MHL) LAN (SERVICE ONLY) USB IN 2 1 PTC SERVICE Mobile phone REMOTE CONTROL 25 REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To install batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution. To remove the batteries, perform the installation actions in reverse. CAUTION ••Do not mix old and new batteries, as this may damage the remote control. This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor. For LY750H series (POWER) Q.MENU TV Q.MENU Selects the remote’s operating mode: TV. DVD Selects the remote’s operating mode: DVD. INPUT MARK INPUT TV 4 7 .,;@ ghi pqrs 2 5 8 Number button MARK abc jkl tuv 0 3 6 9 - (Dash) DELETE CC wxyz Turns the TV off in a set amount of time. DELETE Deletes letters and numbers. MUTE CH P A G E Mutes all sounds. CH Scrolls through the saved channels. PAGE Moves to the previous or next screen. PORTAL Displays and removes the interactive menu. INFO GUIDE Views the information of the current program. GUIDE Displays and removes the electronic program guide. Navigation buttons (up/down/left/right) OK/ENTER ꕣ (BACK) OK ENTER EXIT Scrolls through menus or options. Selects menus or options and confirms your input. Returns to the previous screen. MENU/SETTINGS EXIT ꕯ MENU SETTINGS Switches between Letter and Number input modes. Selects a closed caption. TIMER FLASHBK MUTE PORTAL INFO Adjusts the volume level. CHAR/NUM CC VOL Tunes to the last channel or input viewed. VOL mno Enters numbers. Also supports characters. Inserts a dash between numbers such as 2-1 and 2-2. FLASHBK def CHAR/NUM TIMER Changes the input source. Not functional Accesses the main menu. Clears all on-screen displays and returns to TV viewing. : Red, : Green, Color buttons ( special functions in some menus. : Yellow, : Blue) These access Control buttons ( , , , , ) Controls the MY MEDIA menus or the SIMPLINK compatible devices (USB, SIMPLINK). Accesses the AV devices connected to the TV; Opens the SIMPLINK menu. PIP PIPCH+ PIPCH- SWAP PIP INPUT SAP PIP Enters the split screen mode. (Some input sources may not be displayed.) PIP CH +/SWAP Channel up or down the sub window. Changes the main window and the sub window. PIP INPUT Rotates through input of the sub window. SAP Analog mode: Selects MTS sound (Mono, Stereo or SAP) DTV mode: Changes the audio language. ENGLISH 1 DVD Turns the TV on or off. Not functional. 26 REMOTE CONTROL For LY760H series (POWER) SMART TV SMART TV 1 4 7 .,;@ ghi pqrs 2 5 8 abc jkl tuv 0 3 6 9 TIMER - (Dash) VD/ CC FLASHBK Selects a closed caption. Enables VD function. SAP (Secondary Audio Program) feature can also VD/ be enabled by pressing the VD key. DELETE ENGLISH MUTE PORTAL INFO Tunes to the last channel or input viewed. VOL Adjusts the volume level. CHAR/NUM Switches between Letter and Number input modes. wxyz CH GUIDE P A G E Deletes letters and numbers. MUTE Mutes all sounds. CH Scrolls through the saved channels. PAGE Moves to the previous or next screen. PORTAL Displays and removes the interactive menu. INFO Views the information of the current program. GUIDE Displays and removes the electronic program guide. Navigation buttons (up/down/left/right) OK ENTER OK/ENTER ꕣ (BACK) MENU SETTINGS Enters numbers. Also supports characters. Inserts a dash between numbers such as 2-1 and 2-2. FLASHBK mno CC DELETE Changes the input source. Turns the TV off in a set amount of time. Number button def CHAR/NUM VOL Selects the remote’s operating mode: DVD. INPUT TIMER DVD Selects the remote’s operating mode: TV. DVD INPUT Turns the TV on or off. Accesses the Smart menu. EXIT Returns to the previous screen. MENU/SETTINGS EXIT Scrolls through menus or options. Selects menus or options and confirms your input. Accesses the main menu. Clears all on-screen displays and returns to TV viewing. : Red, : Green, Color buttons ( special functions in some menus. : Yellow, : Blue) These access Control buttons ( , , , , ) Controls the MY MEDIA menus or the SIMPLINK compatible devices (USB, SIMPLINK). PIP PIPCH+ SWAP PIP INPUT PIPCH- Feature can only be enabled or disabled by installer menu settings. Configuration of this feature is not supported on TV remote control. PIP Not functional PIP CH +/SWAP Not functional Not functional PIP INPUT Not functional Not functional MAINTENANCE / TROUBLESHOOTING 27 MAINTENANCE Cleaning your TV Clean your TV regularly to keep it at peak performance and to extend the product’s lifespan. CAUTION ••Before cleaning, turn the power off and disconnect the power cord and all other cables. ••When the TV is left unattended or unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges. Screen, Frame, Cabinet, and Stand To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth. To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth. CAUTION Power Cord Remove the accumulated dust or dirt on the power cord regularly. TROUBLESHOOTING The software may be updated for improvement in performance. The customer is responsible to ensure the compatibility of their equipment with any LG Electronics software. If needed, please consult with LG Electronics and update new software versions according to the guidance provided by LG Electronics. Problem Solution ••Check if anything such as tape has been placed over the receiver. Cannot control the TV with ••Check if there is any obstacle between the product and the remote the remote control. control. ••Replace the batteries with new fresh ones. ••Check if the product is turned on. No image display and no ••Check if the power cord is connected to a wall outlet. sound is produced. ••Check if there is a problem in the wall outlet by connecting other products. ••Check the power control settings. The power supply may be interrupted. The TV turns off suddenly. ••Check if the auto off feature is activated in the Time settings. When connecting to the ••Turn the TV off/on using the remote control. PC (RGB/HDMI/DVI), No ••Reconnect the RGB/HDMI/DVI cable. signal or Invalid Format is ••Restart the PC with the TV on. displayed. ENGLISH ••Do not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in scratches on the screen and image distortions. ••Do not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air fresheners, or lubricants, as these may damage the screen’s finish and cause discoloration. ••Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction. 28 SPECIFICATIONS SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. Power requirement AC 100 - 240 V ~ 50 / 60 Hz Television System ATSC, NTSC-M, 64 & 256 QAM Program Coverage VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135 External Antenna Impedance 75 Ω Environment condition Operating Temperature 0 °C to 40 °C (32 °F to 104 °F) Operating Humidity Less than 80 % Storage Temperature -20 °C to 60 °C (-4 °F to 140 °F) Storage Humidity Less than 85 % MODELS Dimensions (W x H x D) ENGLISH Weight With stand Without stand 32LY750H (32LY750H-UA) 732 x 482 x 282 (mm) 28.8 x 18.9 x 11.1 (inches) 732 x 437 x 55.5 (mm) 28.8 x 17.2 x 2.1 (inches) With stand 8.9 kg (19.6 lbs) Without stand 6.0 kg (13.2 lbs) Current Value / Power Consumption MODELS Dimensions (W x H x D) Weight With stand Without stand 1.25 A / 75 W 39LY750H (39LY750H-UA) 885 x 572 x 282(mm) 885 x 524 x 55.5 (mm) 34.8 x 20.6 x 2.1 (inches) With stand 10.9 kg (24.0 lbs) Without stand 8.0 kg (17.6 lbs) MODELS Weight 39LY760H (39LY760H-UA) 34.8 x 22.5 x 11.1 (inches) Current Value / Power Consumption Dimensions (W x H x D) 32LY760H (32LY760H-UA) With stand Without stand 1.0 A / 100 W 42LY750H (42LY750H-UA) 42LY760H (42LY760H-UA) 961 x 617 x 325 (mm) 37.8 x 24.2 x 12.7 (inches) 961 x 567 x 55.5 (mm) 37.8 x 22.3 x 2.1 (inches) With stand 12.6 kg (27.7 lbs) Without stand 9.2 kg (20.2 lbs) Current Value / Power Consumption 1.1 A / 110 W SPECIFICATIONS 47LY750H (47LY750H-UA) MODELS Dimensions (W x H x D) Weight 42.2 x 26.7 x 12.7 (inches) 1,073 x 629 x 55.8 (mm) Without stand 42.2 x 24.7 x 2.1 (inches) With stand 15.7 kg (34.6 lbs) Without stand 12.3 kg (27.1 lbs) 1.2 A / 120 W 55LY750H (55LY750H-UA) MODELS Weight 55LY760H (55LY760H-UA) 1,243 x 771 x 325 (mm) With stand 48.9 x 30.3 x 12.7 (inches) 1,243 x 725 x 56.8 (mm) Without stand 48.9 x 28.5 x 2.2 (inches) 20.7 Kg (45.6 lbs) Without stand 17.3 Kg (38.1 lbs) 1.4 A / 140 W HDMI (PC) supported mode Horizontal Frequency (kHz) ENGLISH With stand Current Value / Power Consumption Resolution 47LY760H (47LY760H-UA) 1,073 x 680 x 325 (mm) With stand Current Value / Power Consumption Dimensions (W x H x D) 29 HDMI (DTV) supported mode Vertical Frequency (Hz) 640 x 350 31.468 70.09 720 x 400 31.469 70.08 640 x 480 31.469 59.94 800 x 600 37.879 60.31 1024 x 768 48.363 60.00 1152 x 864 54.348 60.053 1360 x 768 47.712 1280 x 1024 1920 x 1080 Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 31.47 59.94 31.50 60.00 44.96 59.94 45.00 60.00 33.72 59.94 33.75 60.00 60.015 26.97 23.976 63.981 60.02 27.00 24.00 67.50 60.00 33.71 29.97 33.75 30.00 67.432 59.94 67.50 60.00 720 x 480p 1280 x 720p 1920 x 1080i 1920 x 1080p 30 SPECIFICATIONS For LY750H series Wireless LAN module (WN8122E1) specification Standard IEEE802.11a/b/g/n 2400 to 2483.5 MHz Frequency ragne 5150 to 5250 MHz 5725 to 5850 MHz 802.11a: 16.5 dBm 802.11b: 16 dBm Output power (Max.) 802.11g: 15.5 dBm 802.11n - 2.4 GHz: 15.5 dBm 802.11n - 5 GHz: 16.5 dBm ENGLISH ••Because band channel used by the country could be different, the user can not change or adjust the operating frequency and this product is set for the regional frequency table. ••This device should be installed and operated with minimum distance 20 cm between the device and your body. And this phrase is for the general statement for consideration of user environment. ••Contains FCC ID: BEJWN8122E1 ••Contains IC: 2703H-WN8122E1 For LY760H series Wireless module (LGSBW41)Specifications Wireless LAN Standard IEEE 802.11a/b/g/n Bluetooth Standard Bluetooth Version 3.0 Frequency range 2400 to 2483.5 MHz 2400 to 2483.5 MHz Frequency ragne 5150 to 5250 MHz 5725 to 5850 MHz 802.11a: 11.5 dBm Output power (Max.) 802.11b: 11 dBm 802.11g: 10.5 dBm 802.11n - 2.4 GHz: 11 dBm Output power (Max.) 10 dBm or Lower 802.11n - 5 GHz: 12.5 dBm ••Because band channel used by the country could be different, the user can not change or adjust the operating frequency and this product is set for the regional frequency table. ••This device should be installed and operated with minimum distance 20 cm between the device and your body. And this phrase is for the general statement for consideration of user environment. ••Contains FCC ID: BEJLGSBW41 ••Contains IC: 2703H-LGSBW41 CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS THE CONSUMER ELECTRONICS INDUSTRY CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations. Televisions that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc., may fall over, resulting in injury. TUNE IN TO SAFETY • ALWAYS follow the manufacturer’s recommendations for the safe installation of your television. • ALWAYS read and follow all instructions for proper use of your television. • NEVER allow children to climb on or play on the television or the furniture on which the television is placed. • NEVER place the television on furniture that can easily be used as steps, such as a chest of drawers. • ALWAYS install the television where it cannot be pushed, pulled over or knocked down. • ALWAYS route cords and cables connected to the television so that they cannot be tripped over, pulled or grabbed. WALL OR CEILING MOUNT YOUR TELEVISION • ALWAYS contact your retailer about professional installation if you have any doubts about your ability to safely mount your television. • ALWAYS use a mount that has been recommended by the television manufacturer and has a safety certification by an independent laboratory (such as UL, CSA, ETL). • ALWAYS follow all instructions supplied by the television and mount manufacturers. • ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate. Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder block construction. If you are unsure, contact a professional installer. • Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount installation. MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME • Many new television buyers move their older CRT televisions into a secondary room after the purchase of a flat-panel television. Special care should be made in the placement of older CRT televisions. • ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size and weight. • NEVER place your older CRT television on a dresser where children may be tempted to use the drawers to climb. • ALWAYS make sure your older CRT television does not hang over the edge of your furniture. CE.org/safety Declaration of Conformity Trade Name: LG Model: 32/39/42/47/55LY750H-UA, 32/39/42/47/55LY760H-UA Responsible Party: LG Electronics Inc. Address: 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A TEL: 201-266-2534 The model and serial number of the TV are located on the back and on one side of the TV. Record them below should you ever need service. MODEL SERIAL LG Customer Information Center For inquires or comments, visit www.lg.com or call; 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA This product qualifies for ENERGY STAR in the factory default (Home Use) setting. Changing the factory default settings or enabling other features may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR. Refer to ENERGYSTAR.gov for more information on the ENERGY STAR program.