HPE FlexNetwork 5130 HI Switch Series data sheet

Data sheet
HPE FlexNetwork 5130 HI
Switch Series
Key features
•Scalable with 10 Gigabit uplinks and nine-chassis IRF with up to 80 Gbps stacking
bandwidth
•PoE+ for up to 30 W of PoE power per port on all ports simultaneously
•Four convenient built-in SFP+ 10GbE uplinks provide performance for bandwidth hungry
applications
•OpenFlow 1.3 support
•MACsec support
Product overview
The HPE FlexNetwork 5130 HI Switch Series comprises Gigabit Ethernet switches that
support static and RIP Layer 3 routing, diversified services, and IPv6 forwarding, as well as
provide four 10 Gigabit Ethernet (10GbE) interfaces.
Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several
switches as one logical device, which increases network resilience, performance, and availability,
while reducing operational complexity. These switches provide Gigabit Ethernet access and
can be used at the edge of a network or to connect server clusters in small data centers.
High availability, simplified management, and comprehensive security control policies are
among the key features that distinguish this series. This switch also supports dual modular
power supplies.
Data sheet
Page 2
Features and benefits
Software-defined networking
•OpenFlow
Supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data
(packet forwarding) and control (routing decision) paths
Quality of Service (QoS)
•Broadcast control
Allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic
•Advanced classifier-based QoS
Classifies traffic using multiple match criteria based on Layers 2, 3, and 4 information;
applies QoS policies such as setting priority level and rate limit to selected traffic on a port,
VLAN, or entire switch
•Powerful QoS feature
Supports the following congestion actions: strict priority (SP) queuing, weighted round
robin (WRR), and SP+WRR
•Traffic policing
Supports Committed Access Rate (CAR) and line rate
Management
•Remote configuration and management
Enables configuration and management through a secure Web browser or a CLI located on
a remote device
•Manager and operator privilege levels
Provides read-only (operator) and read/write (manager) access on CLI and Web browser
management interfaces
•Command authorization
Leverages RADIUS/HWTACACS to link a custom list of CLI commands to an individual network
administrator’s login; also provides an audit trail
•Secure Web GUI
Provides a secure, easy-to-use graphical interface for configuring the module via HTTPS
•Multiple configuration files
Stores easily to the flash image
•Complete session logging
Provides detailed information for problem identification and resolution
•Remote monitoring (RMON)
Uses standard SNMP to monitor essential network functions; supports events, alarm, history,
and statistics group plus a private alarm extension group
Data sheet
Page 3
•IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
Advertises and receives management information from adjacent devices on a network,
facilitating easy mapping by network management applications
•sFlow® (RFC 3176)
Provides scalable ASIC-based wirespeed network monitoring and accounting with no impact
on network performance; this allows network operators to gather a variety of sophisticated
network statistics and information for capacity planning and real-time network monitoring
purposes
•Management VLAN
Segments traffic to and from management interfaces, including CLI/Telnet, a Web browser
interface, and SNMP
•Remote intelligent mirroring
Mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote
switch port anywhere on the network
•Device Link Detection Protocol (DLDP)
Monitors a cable between two compatible switches and shuts down the ports on both ends
if the cable is broken, which prevents network problems such as loops
•IPv6 management
Provides future-proof networking because the switch is capable of being managed whether
the attached network is running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6,
DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and RADIUS for IPv6
•Troubleshooting
Ingress and egress port monitoring enables network problem-solving; virtual cable tests
provide visibility into cable problems
•HPE Intelligent Management Center (IMC)
Integrates fault management, element configuration, and network monitoring from a central
vantage point; built-in support for third-party devices enables network administrators to
centrally manage all network elements with a variety of automated tasks, including discovery,
categorization, baseline configurations, and software images; the software also provides
configuration comparison tools, version tracking, change alerts, and more
Connectivity
•Auto-MDIX
Automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports
•Flow Control
Provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic
situations
•High-density connectivity
Provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Lite Layer 3 switch
Data sheet
Page 4
•IEEE 802.3at Power over Ethernet (PoE+) support
Simplifies deployment and dramatically reduces installation costs by helping to eliminate
the time and cost involved in supplying local power at each access point location
•Ethernet operations, administration, and maintenance (OAM)
Detects data link layer problems that occurred in the “last mile” using the IEEE 802.3ah
OAM standard; monitors the status of the link between two devices
Performance
•Non-blocking architecture
Up to 216 Gbps non-blocking switching fabric provides wirespeed switching with up to
190.5 million pps throughput
•Hardware-based wirespeed access control lists (ACLs)
Help provide high levels of security and ease of administration without impacting network
performance with a feature-rich TCAM-based ACL implementation
Resiliency and high availability
•Separate data and control paths
Separates control from services and keeps service processing isolated; increases security
and performance
•Smart Link
Allows under 100 ms failover between links
•Spanning Tree/PVST+, MSTP, RSTP
Provides redundant links while preventing network loops
•Intelligent Resilient Fabric (IRF)
Creates virtual resilient switching fabrics, where two to nine switches perform as a single
L2 switch and L3 router; switches do not have to be colocated and can be part of a
disaster-recovery system; servers or switches can be attached using standard LACP for
automatic load balancing and high availability; can eliminate need for complex protocols
like Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying
network operation
•Internal Dual Redundant Power Supply
Provides high reliability by keeping network up while delivering up to 1440 W of PoE+
Manageability
•Dual-flash images
Provides independent primary and secondary operating system files for backup while
upgrading
•Multiple configuration files
Allow multiple configuration files to be stored to a flash image
Data sheet
Page 5
•IPv6 management
Future-proofs networking, as the switch is capable of being managed whether the attached
network is running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6,
and ARPv6
•Troubleshooting
Allows ingress and egress port monitoring, enabling network problem solving; virtual cable
tests provide visibility into cable problems
Layer 2 switching
•32K MAC address table
Provides access to many Layer 2 devices
•VLAN support and tagging
Supports IEEE 802.1Q with 4094 simultaneous VLAN IDs
•IEEE 802.1ad QinQ and selective QinQ
Increase the scalability of an Ethernet network by providing a hierarchical structure; connect
multiple LANs on a high-speed campus or metro network
•10GbE port aggregation
Allows grouping of ports to increase overall data throughput to a remote device
•Device Link Detection Protocol (DLDP)
Monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected,
preventing loops in STP-based networks
•Jumbo frame support
Improves the performance of large data transfers; supports frame size of up to 9K bytes
Layer 3 services
•Address Resolution Protocol (ARP)
Determines the MAC address of another IP host in the same subnet; supports static ARPs;
gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP
operation between subnets or when subnets are separated by a Layer 2 network
•Dynamic Host Configuration Protocol (DHCP)
Simplifies the management of large IP networks; supports client; DHCP Relay enables
DHCP operation across subnets
•Loopback interface address
Defines an address that can always be reachable, improving diagnostic capability
•User Datagram Protocol (UDP) helper function
Allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet
broadcast addresses and prevents server spoofing for UDP services such as DHCP
Data sheet
Page 6
•Route maps
Provide more control during route redistribution; allow filtering and altering of route metrics
•DHCP server
Centralizes and reduces the cost of IPv4 address management
Layer 3 routing
•Static IP routing
Provides manually configured routing for both IPv4 and IPv6 networks
•Routing Information Protocol (RIP)
Uses a distance vector algorithm with UDP packets for route determination; supports
RIPv1 and RIPv2 routing; includes loop protection
•Policy Based Routing
Provides a mechanism for indicating and executing forwarding/routing of data packets
based on the policies defined by the network administrator
Security
•Access control lists (ACLs)
Provides IP Layer 2 to Layer 4 traffic filtering; supports global ACL, VLAN ACL, port ACL,
and IPv6 ACL
•IEEE 802.1X
Industry-standard method of user authentication using an IEEE 802.1X supplicant on
the client in conjunction with a RADIUS server
•MAC-based authentication
Client is authenticated with the RADIUS server based on the client’s MAC address
•Identity-driven security and access control
––Per-user ACLs
Permits or denies user access to specific network resources based on user identity and
time of day, allowing multiple types of users on the same network to access specific
network services without risking network security or providing unauthorized access to
sensitive data
––Automatic VLAN assignment
Automatically assigns users to the appropriate VLAN based on their identities
•Secure management access
Delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL,
HTTPS, and/or SNMPv3
•Secure FTP/SCP
Allows secure file transfer to and from the switch; protects against unwanted file downloads
or unauthorized copying of a switch configuration file
•Guest VLAN
Provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
Data sheet
Page 7
•Port security
Allows access only to specified MAC addresses, which can be learned or specified
by the administrator
•Port isolation
Secures and adds privacy, and prevents malicious attackers from obtaining user information
•STP BPDU port protection
Blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing
forged BPDU attacks
•STP root guard
Protects the root bridge from malicious attacks or configuration mistakes
•DHCP protection
Blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
•RADIUS/HWTACACS
Eases switch management security administration by using a password authentication server
•Endpoint Admission Defense (EAD)
Provides security policies to users accessing a network
•IPv6 source guard
Helps prevent IPv6 spoofing attacks using ND Snooping as well as DHCPv6 Snooping
Convergence
•IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
Facilitates easy mapping using network management applications with LLDP automated
device discovery protocol
•LLDP-MED (Media Endpoint Discovery)
Defines a standard extension of LLDP that stores values for parameters such as QoS and
VLAN to automatically configure network devices such as IP phones
•LLDP-CDP compatibility
Receives and recognizes CDP packets from Cisco’s IP phones for seamless interoperation
•IEEE 802.3at Power over Ethernet (PoE+)
Provides up to 30 W per port that allows support of the latest PoE+-capable devices
such as IP phones, wireless access points, and security cameras, as well as any IEEE
802.3af-compliant end device; eliminates the cost of additional electrical cabling and
circuits that would otherwise be necessary in IP phone and WLAN deployments
Data sheet
Page 8
•PoE allocations
Supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified)
to allocate PoE power for more efficient energy savings
•Voice VLAN
Automatically assigns VLAN and priority for IP phones, simplifying network configuration
and maintenance
•IP multicast snooping (data-driven IGMP)
Prevents flooding of IP multicast traffic
•Internet Group Management Protocol (IGMP)
Utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4
multicast networks; supports IGMPv1, v2, and v3
Device support
•Pre-standard PoE support
Detects and provides power to pre-standard PoE devices such as wireless LAN access
points and IP phones
Additional information
•Green IT and power
Improves energy efficiency through the use of the latest advances in silicon development;
shuts off unused ports and utilizes variable-speed fans, reducing energy costs
•Green initiative support
Provides support for RoHS and WEEE regulations
•Unified HPE Comware operating system with modular architecture
Provides an easy-to-enhance-and-extend feature set, which doesn’t require whole-scale
changes; all switching, routing, and security platforms leverage the Comware OS, a common
unified modular operating system
•Energy Efficient Ethernet (EEE) support
Reduces power consumption in accordance with IEEE 802.3az
Warranty and support
•Limited Lifetime Warranty
See hpe.com/networking/warrantysummary for warranty and support information
included with your product purchase
•Software releases
To find software for your product, refer to hpe.com/networking/support; for details on
the software releases available with your product purchase, refer to hpe.com/networking/
warrantysummary
Data sheet
Page 9
HPE FlexNetwork 5130 HI Switch Series
Specifications
HPE 5130 24 G 4SFP+ hi with 1 interface slot switch
(JH323A)
HPE 5130 48 G 4SFP+ hi with 1 interface slot switch
(JH324A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only; Ports 1–8 support MACsec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports,
with optional module
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only; Ports 1–8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports,
with optional module
Additional ports and slots
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
Airflow direction is Front (port side) to Back (power cord side)
Airflow direction is Front (port side) to Back (power cord side)
17.32(w) x 14.17(d) x 1.72(h) in. (44.00 x 36.00 x 4.37 cm)
(1U height)
16.53 lb (7.5 kg) shipping weight
17.32(w) x 14.17(d) x 1.72(h) in. (44.0 x 36 x 4.37 cm)
(1U height)
16.53 lb (7.5 kg)
Memory and processor
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounting and enclosure
Mounts in an EIA standard 19-inch telco rack or equipment
cabinet (hardware included)
Mounts in an EIA standard 19-inch telco rack or equipment
cabinet (hardware included)
IPv6 Ready Certified
< 5 µs
< 3 µs
Up to 154.8 Mpps
168 Gbps
Up to 4K entries (IPv4), up to 2K entries (IPv6)
32768 entries
IPv6 Ready Certified
< 5 µs
< 3 µs
Up to 190.5 Mpps
216 Gbps
Up to 4K entries (IPv4), up to 2K entries (IPv6)
32768 entries
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
5% to 95%, noncondensing
Low-speed fan: 52.8 dB, High-speed fan: 66.7 dB; ISO 7779
5% to 95%, noncondensing
Low-speed fan: 49.9 dB, High-speed fan: 64.8 dB; ISO 7779
Physical characteristics
Dimensions
Weight
Performance
1000 Mb Latency 10 Gbps Latency
10 Gbps Latency
Throughput
Routing/Switching capacity
Routing table size
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative
humidity
Acoustic
Data sheet
Page 10
HPE FlexNetwork 5130 HI Switch Series
Specifications (continued)
HPE 5130 24 G 4SFP+ hi with 1 interface slot switch
(JH323A)
HPE 5130 48 G 4SFP+ hi with 1 interface slot switch
(JH324A)
50/60 Hz
365 BTU/hr (385.08 kJ/hr), ranges from 167 BTU/hr to 392 BTU/hr,
depending on power supply configuration
100–240 VAC, rated (90–264 VAC, max)
-48 to -60 VDC, rated (-36 to -72 VDC, max) (depending on power
supply chosen)
107 W
55 W
Idle power is the actual power consumption of the device with
no ports connected. Maximum power rating and maximum heat
dissipation are the worst-case theoretical maximum numbers
provided for planning the infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
50/60 Hz
419 BTU/hr (442.04 kJ/hr), ranges from 201 BTU/hr to 443 BTU/hr,
depending on power supply configuration
100–240 VAC, rated (90–264 VAC, max)
-48 to -60 VDC, rated (-36 to -72 VDC, max) (depending on
power supply chosen)
150 W
70 W
Idle power is the actual power consumption of the device with
no ports connected. Maximum power rating and maximum heat
dissipation are the worst-case theoretical maximum numbers
provided for planning the infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR
Subchapter J; RoHS Compliance; AS/NZS 60950-1; GB 4943;
EAC (EurAsian Conformity Certification)
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR
Subchapter J; RoHS Compliance; AS/NZS 60950-1; GB 4943;
EAC (EurAsian Conformity Certification)
Emissions
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A;
EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008;
VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009;
EN 61000-3-2:2006+A1:2009+A2:2009; EN 61000-4-3:2006;
EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009;
AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A;
EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010;
EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A;
EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008;
VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009;
EN 61000-3-2:2006+A1:2009+A2:2009; EN 61000-4-3:2006;
EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009;
AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A;
EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010;
EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
EN 55024
EN300 386
EN 55024
EN300 386
Management
IMC—Intelligent Management Center; command-line interface;
Web browser; SNMP manager
IMC—Intelligent Management Center; command-line interface;
Web browser; SNMP manager
Services
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and
response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
Voltage
Maximum power rating
Idle power
Notes
Immunity
Generic
ESD
Data sheet
Page 11
HPE FlexNetwork 5130 HI Switch Series
Specifications (continued)
HPE 5130 24 G POE+ 4SFP+ hi with 1 interface slot switch
(JH323A)
HPE 5130 48 G POE+ 4SFP+ hi with 1 interface slot switch
(JH324A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only; Ports 1–8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports,
with optional module
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3
Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T, IEEE 802.3at PoE+);
Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only; Ports 1–8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports,
with optional module
Additional ports and slots
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
2 power supply slots
1 minimum power supply required (ordered separately)
Fan tray
Airflow direction is Front (port side) to Back (power cord side)
Airflow direction is Front (port side) to Back (power cord side)
17.32(w) x 18.11(d) x 1.72(h) in. (43.99 x 46 x 4.37 cm)
(1U height)
27.56 lb (12.5 kg) shipping weight
17.32(w) x 18.11(d) x 1.72(h) in. (43.99 x 46 x 4.37 cm)
(1U height)
27.56 lb (12.5 kg) shipping weight
Memory and processor
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounting and enclosure
Mounts in an EIA standard 19-inch telco rack or equipment
cabinet (hardware included)
Mounts in an EIA standard 19-inch telco rack or equipment
cabinet (hardware included)
IPv6 Ready Certification
< 5 µs
< 3 µs
Up to 154.8 Mpps
168 Gbps
Up to 4K entries (IPv4), up to 2K entries (IPv6)
32768 entries
IPv6 Ready Certification
< 5 µs
< 3 µs
Up to 190.5 Mpps
216 Gbps
Up to 4K entries (IPv4), up to 2K entries (IPv6)
32768 entries
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
5% to 95%, noncondensing
Low-speed fan: 57.6 dB, High-speed fan: 66.9 dB; ISO 7779
5% to 95%, noncondensing
Low-speed fan: 57.6 dB, High-speed fan: 66.9 dB; ISO 7779
Physical characteristics
Dimensions
Weight
Performance
1000 Mb Latency 10 Gbps Latency
10 Gbps Latency
Throughput
Routing/Switching capacity
Routing table size
MAC address table size
Environment
Operating temperature
Operating relative humidity
Nonoperating/Storage temperature
Nonoperating/Storage relative
humidity
Acoustic
Data sheet
Page 12
HPE FlexNetwork 5130 HI Switch Series
Specifications (continued)
HPE 5130 24 G POE+ 4SFP+ hi with 1 interface slot switch
(JH325A)
HPE 5130 48 G POE+ 4SFP+ hi with 1 interface slot switch
(JH326A)
50/60 Hz
2217 BTU/hr (3599.66 kJ/hr), ranges from 228 BTU/hr
to 3412 BTU/hr, depending on power supply configuration
100–240 VAC, rated (90–264 VAC, max)
(depending on power supply chosen)
650 W
67 W
740 W PoE+
Idle power is the actual power consumption of the device with
no ports connected. Maximum power rating and maximum heat
dissipation are the worst-case theoretical maximum numbers
provided for planning the infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE+ power range is from 450 W to 740 W. PoE+ power is
the power supplied by the internal power supply(ies). It is
dependent on the type and quantity of power supplies. Device
supports 1 or 2 internal modular power supplies.
50/60 Hz
2286 BTU/hr (2411.73 kJ/hr), ranges from 256 BTU/hr
to 6142 BTU/hr, depending on power supply configuration
100–240 VAC, rated (90–264 VAC, max)
(depending on power supply chosen)
670 W
75 W
1440 W PoE+
Idle power is the actual power consumption of the device with
no ports connected. Maximum power rating and maximum heat
dissipation are the worst-case theoretical maximum numbers
provided for planning the infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE+ power range is from 450 W to 1440 W. PoE+ power
is the power supplied by the internal power supply(ies). It is
dependent on the type and quantity of power supplies. Device
supports 1 or 2 internal modular power supplies.
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR
Subchapter J; RoHS Compliance; AS/NZS 60950-1; GB 4943;
EAC (EurAsian Conformity Certification)
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1;
EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1;
EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR
Subchapter J; RoHS Compliance; AS/NZS 60950-1; GB 4943;
EAC (EurAsian Conformity Certification)
Emissions
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A;
EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008;
VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009;
EN 61000-3-2:2006+A1:2009+A2:2009; EN 61000-4-3:2006;
EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009;
AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A;
EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010;
EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A;
EN 61000-4-11:2004; ANSI C63.4-2009; EN 61000-3-3:2008;
VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009;
EN 61000-3-2:2006+A1:2009+A2:2009; EN 61000-4-3:2006;
EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009;
AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A;
EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010;
EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
EN 55024
EN300 386
EN 55024
EN300 386
Management
IMC—Intelligent Management Center; command-line interface;
Web browser; SNMP manager
IMC—Intelligent Management Center; command-line interface;
Web browser; SNMP manager
Services
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Refer to the Hewlett Packard Enterprise website at
hpe.com/networking/services for details on the service-level
descriptions and product numbers. For details about services
and response times in your area, please contact your local
Hewlett Packard Enterprise sales office.
Electrical characteristics
Frequency
Maximum heat dissipation
Voltage
Maximum power rating
Idle power
PoE power
Notes
Immunity
Generic
ESD
Data sheet
Page 13
Standards and protocols
(Applies to all products in series)
Device management
RFC 1155 Structure and Mgmt Information
(SMIv1)
RFC 1157 SNMPv1/v2c
RFC 1305 NTPv3
RFC 2573 (SNMPv3 Applications)
RFC 2578 SMIv2
RFC 2819 (RMON groups Alarm, Event,
History, and Statistics only)
RFC 3416 (SNMP Protocol Operations v2)
RFC 3417 (SNMP Transport Mappings)
HTML and Telnet management
Multiple Configuration Files
SNMPv3 and RMON RFC support SSHv1/
SSHv2 Secure Shell
TACACS/TACACS+
Web UI
General protocols
IEEE 802.1ad QinQ
IEEE 802.1ak Multiple Registration Protocol
(MRP) and Multiple VLAN Registration
Protocol (MVRP)
IEEE 802.1AX-2008 Link Aggregation
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q (GVRP)
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol
and Port
IEEE 802.1w Rapid Reconfiguration of
Spanning Tree
IEEE 802.1X PAE
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ac VLAN Tagging Extension
IEEE 802.3ad Link Aggregation Control
Protocol (LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 855 Telnet Option Specification
RFC 894 IP over Ethernet
RFC 950 Internet Standard Subnetting
Procedure
RFC 951 BOOTP
RFC 1027 Proxy ARP
RFC 1042 IP Datagrams
RFC 1071 Computing the Internet
Checksum
RFC 1123 Requirements for Internet Hosts
RFC 1213 Management Information Base
for Network Management of TCP/IP-based
Internets
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1533 DHCP Options and BOOTP
Vendor
Extensions
RFC 1591 DNS (client only)
RFC 1812 IPv4 Routing
RFC 1866 Hypertext Markup Language-2.0
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2462 IPv6 Stateless Address
Autoconfiguration
RFC 2474 Definition of the Differentiated
Services Field (DS Field) in the IPv4 and
IPv6 Headers
RFC 2475 Architecture for Differentiated
Services
RFC 2597 Assured Forwarding PHB Group
RFC 2616 HTTP Compatibility v1.1
RFC 2665 Definitions of Managed Objects
for the Ethernet-like Interface Types
RFC 2668 Definitions of Managed Objects for
IEEE 802.3 Medium Attachment Units (MAUs)
RFC 2865 Remote Authentication Dial In User
Service (RADIUS)
RFC 2866 RADIUS Accounting
RFC 2868 RADIUS Attributes for Tunnel
Protocol Support
RFC 3246 Expedited Forwarding PHB
RFC 3414 User-based Security Model
(USM) for version 3 of the Simple Network
Management Protocol (SNMPv3)
RFC 3415 View-based Access Control Model
(VACM) for the Simple Network Management
Protocol (SNMP)
RFC 3416 Protocol Operations for SNMP
RFC 3417 Transport Mappings
RFC 3418 Management Information Base
(MIB) for the Simple Network Management
Protocol (SNMP)
RFC 3576 Ext to RADIUS (CoA only)
RFC 3587 IPv6 Global Unicast Address Format
RFC 3810 Multicast Listener Discovery
Version 2 (MLDv2) for IPv6
RFC 4213 Basic IPv6 Transition Mechanisms
RFC 4291 IP Version 6 Addressing
Architecture
RFC 4541 Considerations for Internet Group
Management Protocol (IGMP) and Multicast
Listener Discovery (MLD) Snooping Switches
RFC 4575 A Session Initiation Protocol (SIP)
Event Package for Conference State
RFC 4675 RADIUS VLAN & Priority
RFC 5095 Deprecation of Type 0 Routing
Headers in IPv6
802.1r–GARP Proprietary Attribute
Registration Protocol (GPRP)
IP multicast
RFC 1112 IGMPv1
RFC 3376 IGMPv3
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over
Ethernet
Networks
RFC 3162 RADIUS and IPv6
RFC 3306 Unicast-Prefix-based
IPv6 Multicast Addresses
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for
IPv6
RFC 3736 Stateless Dynamic Host
Configuration Protocol (DHCP) Service for
IPv6
RFC 4291 IP Version 6 Addressing
Architecture
RFC 4293 MIB for IP
RFC 4443 ICMPv6
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address
Autoconfiguration
Data sheet
Page 14
Standards and protocols
(Applies to all products in series)
MIBs
RFC 1212 Concise MIB Definitions
RFC 1213 MIB II
RFC 1215 A Convention for Defining Traps
for use with the SNMP
RFC 1493 Bridge MIB RF
C 1757 Remote Network Monitoring MIB
RFC 2096 IP Forwarding Table MIB RFC
2233 Interface MIB RFC
2571 SNMP Framework MIB RFC
2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB RFC
2574 SNMP USM MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB RFC
2668 802.3 MAU MIB RFC
2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (version 2)
RFC 2819 RMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-user based-SM MIB
RFC 3415 SNMP-view based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol
(LLDP) RFC 2579 Textual Conventions for
SMIv2
RFC 1215 A Convention for Defining Traps
for use with the SNMP
RFC 2579 Textual Conventions for SMIv2
RFC 2580 Conformance Statements for
SMIv2
RFC 2818 HTTP over TLS
RFC 2819 Four groups of RMON: 1 (statistics),
2 (history), 3 (alarm), and 9 (events)
RFC 6398 IP Router Alert Considerations and
Usage
ANSI/TIA-1057 LLDP Media Endpoint
Discovery (LLDP-MED)
SNMPv1/v2c/v3
QoS/CoS
RFC 2474 DS Field in the IPv4 and
IPv6 Headers
RFC 3260 New Terminology and Clarifications
for DiffServ
Security
IEEE 802.1X Port Based Network Access
Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2139 RADIUS Accounting
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
RFC 3260 New Terminology and Clarifications
for DiffServ
RFC 4716 SSH Public Key File Format
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
HPE FlexNetwork 5130 HI Switch Series accessories
Modules
NEW HPE 5130/5510 10GBASE-T 2-port Module (JH156A)1
NEW HPE 5130/5510 10GbE SFP+ 2-port Module (JH157A)1
Transceivers
HPE X125 1G SFP LC LH40 1310nm Transceiver (JD061A)2
HPE X120 1G SFP LC LH40 1550nm Transceiver (JD062A)2
HPE X125 1G SFP LC LH70 Transceiver (JD063B)2
HPE X120 1G SFP LC LH100 Transceiver (JD103A)2
HPE X120 1G SFP LC SX Transceiver (JD118B)2
HPE X120 1G SFP LC LX Transceiver (JD119B)2
HPE X120 1G SFP LC BX 10-U Transceiver (JD098B)2
HPE X120 1G SFP LC BX 10-D Transceiver (JD099B)2
HPE X120 1G SFP RJ45 T Transceiver (JD089B)2
HPE X130 10G SFP+ LC SR Transceiver (JD092B)
HPE X130 10G SFP+ LC LR Transceiver (JD094B)
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable (JD095C)
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable (JD096C)
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (JD097C)
HPE X130 10G SFP+ LC ER 40km Transceiver (JG234A)3
HPE X130 10G SFP+ LC LH 80km Transceiver (JG915A)3
HPE X130 10G SFP+ LC LRM Transceiver (JD093B)3
1
Module supports MACsec
2
Transceiver cannot be used on optional module JH157A
3
Transceiver can only be used on optional module JH157A
Data sheet
Page 15
HPE FlexNetwork 5130 HI Switch Series accessories (continued)
Cables
HPE 0.5 m Multimode OM3 LC/LC Optical Cable (AJ833A)
HPE 1 m Multimode OM3 LC/LC Optical Cable (AJ834A)
HPE 2 m Multimode OM3 LC/LC Optical Cable (AJ835A)
HPE 5 m Multimode OM3 LC/LC Optical Cable (AJ836A)
HPE 15 m Multimode OM3 LC/LC Optical Cable (AJ837A)
HPE 30 m Multimode OM3 LC/LC Optical Cable (AJ838A)
HPE 50 m Multimode OM3 LC/LC Optical Cable (AJ839A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable (QK733A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable (QK734A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable (QK735A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable (QK736A)
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable (QK737A)
HPE 5130 24G 4SFP+ HI with 1 Interface Slot Switch (JH323A)
HPE 5500 150WAC Power Supply (JD362A)4
HPE 5500 150WDC Power Supply (JD366A)4
HPE 5130 48G 4SFP+ HI with 1 Interface Slot Switch (JH324A)
HPE 5500 150WAC Power Supply (JD362A)4
HPE 5500 150WDC Power Supply (JD366A)4
HPE 5130 24G PoE+ 4SFP+ HI with 1 Interface Slot Switch (JH325A)
HPE X362 720W 100-240VAC to 56VDC PoE Power Supply (JG544A)4
HPE X362 1110W 115-240VAC to 56VDC PoE Power Supply (JG545A)4
HPE 5130 48G PoE+ 4SFP+ HI with 1 Interface Slot Switch (JH326A)
HPE X362 720W 100-240VAC to 56VDC PoE Power Supply (JG544A)4
HPE X362 1110W 115-240VAC to 56VDC PoE Power Supply (JG545A)4
4
Products covered by 1 year warranty. See details at hpe.com/networking/warrantyquickref
Learn more at
hpe.com/networking
Data sheet
Sign up for updates
© Copyright 2015–2016 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change
without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
sFlow is a registered trademark of InMon Corp.
4AA6-2927ENN, July 2016, Rev. 4
Download PDF
Similar pages