G085VW01 V0
! " Preliminary Specifications
# " Final Specifications
Module
8.5 Inch Color TFT-LCD
Model Name
G085VW01 V0
Customer
Date
Approved by
Debbie Chiu
Checked &
Approved by
Date
2010/07/06
Prepared by
Alan Chen
Note: This Specification is subject to change
without notice.
2010/07/06
General Display Business Division /
AU Optronics corporation
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
1
info@display-solution.com
G085VW01 V0
Contents
1. Operating Precautions.....................................................................................4
2. General Description .........................................................................................5
2.1 Display Characteristics...........................................................................................................5
2.2 Optical Characteristics ...........................................................................................................6
3. Functional Block Diagram ...............................................................................9
4. Absolute Maximum Ratings ..........................................................................10
4.1 Absolute Ratings of TFT LCD Module .................................................................................10
4.2 Absolute Ratings of Environment ........................................................................................10
5. Electrical Characteristics ..............................................................................11
5.1 TFT LCD Module .................................................................................................................. 11
5.2 Backlight Unit........................................................................................................................12
6. Signal Characteristic .....................................................................................13
6.1 Pixel Format Image ..............................................................................................................13
6.2 Signal Description ................................................................................................................14
6.3 Scanning Direction ...............................................................................................................16
6.4 Interface Timing ....................................................................................................................17
6.5 Power ON/OFF Sequence ...................................................................................................20
7. Connector & Pin Assignment ........................................................................21
7.1 TFT LCD Signal (CN1): LCD Connector .............................................................................21
7.2 LED Backlight Unit (CN2): LED Driver Connector ..............................................................21
7.3 LED Light Bar Input Connector (CN4):................................................................................22
8. Reliability Test Criteria ..................................................................................22
9. Mechanical Characteristics ...........................................................................23
9.1 LCM Front View....................................................................................................................23
9.2 LCM Rear View ....................................................................................................................24
10. Label and Packaging....................................................................................25
10.1 Shipping Label (on the rear side of TFT-LCD display) ......................................................25
10.2 Carton Package .................................................................................................................25
11 Safety.............................................................................................................26
11.1 Sharp Edge Requirements.................................................................................................26
11.2 Materials .............................................................................................................................26
11.3 Capacitors...........................................................................................................................26
11.4 National Test Lab Requirement..........................................................................................26
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
2
info@display-solution.com
G085VW01 V0
Record of Revision
Version and Date
0.0 2009/08/28
Page
Old description
All First Edition
New Description
Add Operation Lifetime=50,000
Hrs(Ir=100mA,Ta=25°C)
Add Shipping Label
Add Carton Packing
Contrast Ratio min:400
Color / Chromaticity Coordinates:
0.1 2009/10/22
12
0.2 2010/04/15
25
Shipping Label: TBD
Carton Package: TBD
0.2 2010/04/15
6
Contrast Ratio min:TBD
Color / Chromaticity Coordinates:
Red x, Red y: TBD
Green x. Green y: TBD
Blue x, Blue y:TBD
White x, White y: TBD
0.2 2010/04/15
18
Sync Mode (HV Mode) without min & Max
Sync Mode (HV Mode)
1.0 2010/07/06
11
Irush LCD : Rising time must be <=470us
No VLED rising time
Note 3: IF, VF , PVLED are defined for LED
Light Bar. There is one LED channel in
back light unit.
Unify power volt symbol
VCC
Unify power volt symbol
VCC
Irush LCD : Rising time must be >=470us
Add VLED rising time.
Remove Note 3.
VCC!VLED
12
15
17
18
19
VCC!VDD
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
3
info@display-solution.com
G085VW01 V0
1. Operating Precautions
1)
2)
3)
4)
5)
Since front polarizer is easily damaged, please be cautious not to scratch it.
Be sure to turn off power supply when inserting or disconnecting from input connector.
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard
surface.
6) To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling
TFT-LCD Module.
7) Do not open nor modify the module assembly.
8) Do not press the reflector sheet at the back of the module to any direction.
9) In case if a module has to be put back into the packing container slot after it was taken out
from the container, do not press the center of the LED Reflector edge. Instead, press at the
far ends of the LED Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11)After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do
not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be
taken into consideration that no bending/twisting forces are applied to the TFT Module from
outside. Otherwise the TFT Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Severe temperature condition may result in different luminance, response time.
14) Continuous operating TFT-LCD Module under high temperature environment may accelerate
LED light bar exhaustion and reduce luminance dramatically.
15) The data on this specification sheet is applicable when LCD module is placed in landscape
position.
16) Continuous displaying fixed pattern may induce image sticking. It is recommended to use
screen saver or shuffle content periodically if fixed pattern is displayed on the screen.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
4
info@display-solution.com
G085VW01 V0
2. General Description
This specification applies to the 8.5 inch color TFT LCD module G085VW01 V0.
G085VW01 V0 designed with wide viewing angle; wide operating temperature and long life LEDs
backlight is well suited to be the display units for Industrial Applications.
LED driving board for backlight unit is included in this panel and the structure of the LED units is
replaceable.
G085VW01 V0 is built in timing controller and CMOS interface.
The screen format is intended to support the WVGA (800(H) x 480(V)) screen and 262k colors
(RGB 6-bits).
G085VW01 V0 is a RoHS product.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25
condition:
Items
Unit
Specifications
Screen Diagonal
[inch]
8.5
Active Area
[mm]
184.8(H) x 110.88(V)
Pixels H x V
Pixel Pitch
( 215.5 mm )
800x3(RGB) x 480
[mm]
0.231x 0.231
Pixel Arrangement
R.G.B. Vertical Stripe
Display Mode
TN, Normally White
Nominal Input Voltage VDD
[Volt]
3.3 typ.
Typical Power Consumption
[Watt]
3.5
Weight
[Grams]
250 (Typ.)
Physical Size
[mm]
210.0(W) x 134(H) x 10.0(D) (typ.)
Electrical Interface
CMOS I/F
Surface Treatment
Anti-glare, Hardness 3H
Support Color
262K(6-bit)
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance
[oC]
o
[ C]
-30 to +85 (panel surface temperature)
-30 to +85
RoHS Compliance
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
5
info@display-solution.com
G085VW01 V0
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25
Item
Unit
Conditions
[cd/m2]
IF= 80mA
White Luminance
(center point)
%
Uniformity
9 Points
Contrast Ratio
Response Time
300
-
1
70
75
-
1, 2, 3
400
500
-
4
Rising
-
20
30
[msec]
Falling
-
10
20
[msec]
Raising + Falling
-
30
50
[degree]
[degree]
Horizontal
CR 10
(Right)
(Left)
70
80
-
70
80
-
[degree]
[degree]
Vertical
CR 10
(Upper)
(Lower)
65
80
-
50
60
-
Red x
0.55
0.6
0.65
Red y
0.295
0.345
0.395
Green x
0.275
0.325
0.375
Green y
0.505
0.555
0.605
Blue x
0.1
0.15
0.2
Blue y
0.065
0.115
0.165
White x
0.25
0.30
0.35
White y
0.27
0.32
0.37
-
50
-
Color / Chromaticity
Coordinates
(CIE 1931)
%
Note
210
[msec]
Viewing Angle
Color Gamut
(Room Temperature):
Min.
Typ.
Max.
5
6
1
1
Note 1: Measurement method
Equipment : Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent)
Aperture
Test Point
Center
Environment
< 1 lux
LCD Module
SR_3 or
equivalent
Measuring distance
Module Driving Equipment
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
6
info@display-solution.com
G085VW01 V0
Note 2: Definition of 9 points position (Display active area : 184.8(H) x 110.88(V)!
90 %
10 %
50 %
10 %
50 %
90 %
Note 3: The luminance uniformity of 9 points is defined by dividing the minimum luminance value by the maximum test
point luminance
Minimum Brightness of nine points
#W9 =
Maximum Brightness of nine points
Note 4" Definition of contrast ratio (CR):
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
Note 5: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “White” to “Black”
(falling time) and from “Black” to “White” (rising time), respectively. The response time interval is between 10% and
90% of amplitudes. Please refer to the figure as below.
%
Tf
Tr
100
90
Optical
White
Black
White
response
10
0
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
7
info@display-solution.com
G085VW01 V0
Note 6: Definition of viewing angle
Viewing angle is the measurement of con
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as below: 90° (θ) horizontal
left and right, and 90° (Φ) vertical high (up) and low (down). The measurement direction is typically perpendicular to the
display surface with the screen rotated to its center to develop the desired measurement viewing angle.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
8
info@display-solution.com
G085VW01 V0
3. Functional Block Diagram
The following diagram shows the functional block of the 8.5 inch color TFT/LCD module:
12.2 V
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
9
info@display-solution.com
G085VW01 V0
4. Absolute Maximum Ratings
4.1 Absolute Ratings of TFT LCD Module
Item
Symbol
Min
Max
Unit
Logic/LCD Drive Voltage
VDD
-0.3
+3.6
[Volt]
Conditions
4.2 Absolute Ratings of Environment
Item
Symbol
Min
Max
Unit
Operating Temperature
TOP
-30
+85
[ C]
Operation Humidity
HOP
5
90
[%RH]
Storage Temperature
TST
-30
+85
[ C]
Storage Humidity
HST
5
90
[%RH]
o
o
Note: Maximum Wet-
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
10
info@display-solution.com
G085VW01 V0
5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Symbol
Parameter
Min
Typ
Max
Units
VDD
Logic/LCD
Input Voltage
3.0
3.3
3.6
[Volt]
IVDD
LCD Input Current
135
150
200
[mA]
VDD=3.3V at 60 HZ, all Black Pattern
PVDD
LCD Power
comsumption
-
0.5
!
[Watt]
VDD=3.3V at 60 HZ, all Black Pattern
Remark
Note 1; VDD=3.3V
Irush LCD
LCD Inrush Current
-
-
1.5
[A]
Black Pattern, Rising time must be
>=470us
VDDrp
Allowable Logic/LCD
Drive Ripple Voltage
-
!
100
[mV]
p-p
VDD=3.3V at 60 HZ, all Black Pattern
Note 1: Measurement condition:
3.3V / 12V
90%
10%
0V
470us
VDD & VLED rising time
Provided by
www.display-solution.com
G085VW01 V0 rev. 1.0
11
info@display-solution.com
G085VW01 V0
5.2 Backlight Unit
5.2.1 Parameter guideline for LED backlight
Following characteristics are measured under a stable condition using an inverter at 25
Symbol
Parameter
Min.
Typ.
Max.
Unit
VLED
Input Voltage
10.8
12
12.6
[Volt]
ILED
Input Current
-
0.25
-
[A]
100% PWM Duty
PVLED
Power Consumption
-
3
-
[Watt]
100% PWM Duty
Irush LED
Inrush Current
-
-
1.5
[A]
at rising
time=470us
FPWM
Dimming Frequency
200
-
20K
[Hz]
Swing Voltage VIH
3
3.3
5.5
V
Swing Voltage VIL
-
-
0.15
V
Dimming Duty Cycle
5
-
100
%
Operation
Lifetime
Hrs
50,000
Remark
Ir=100mA
Ta=25°C
Note 1: Ta means ambient temperature of TFT-LCD module.
Note 2: VLED, IvLED, PVLED , Irush LED are defined for LED B/L.(100% duty of PWM dimming)
Note 3: If G085VW01 V0 module is driven by high current or at high ambient temperature & humidity condition. The
operating life will be reduced.
Note 4: Operating life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated
data.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
12
info@display-solution.com
G085VW01 V0
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel format.
1
2
799
800
1st Line
R G B R G B
R G B R G B
480th Line
R G B R G B
R G B R G B
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
13
info@display-solution.com
G085VW01 V0
6.2 Signal Description
Pin No. Symbol
Description
1
GND!
Ground!
2
GND!
Ground!
3
CK!
Clock signal for sampling each data signal!
4
GND!
Ground!
5
GND!
Ground!
6
REV!
Normal :OPEN/GND; Reverse :High!
7
R0!
RED data signal (LSB)!
8
R1!
RED data signal!
9
R2!
RED data signal!
10
GND!
Ground!
11
R3!
RED data signal!
12
R4!
RED data signal!
13
R5!
RED data signal (MSB)!
14
GND!
Ground!
15
G0!
GREEN data signal (LSB)!
16
G1!
GREEN data signal!
17
G2!
GREEN data signal!
18
GND!
Ground!
19
G3!
GREEN data signal!
20
G4!
GREEN data signal!
21
G5!
GREEN data signal (MSB)!
22
GND!
Ground!
23
B0!
BLUE data signal (LSB)!
24
B1!
BLUE data signal!
25
B2!
BLUE data signal!
26
GND!
Ground!
27
B3!
BLUE data signal!
28
B4!
BLUE data signal!
29
B5!
BLUE data signal (MSB)!
30
GND!
Ground!
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
14
info@display-solution.com
G085VW01 V0
Pin No. Symbol
Description
31
Hsync!
Horizontal synchronous signal!
32
GND!
Ground!
33
Vsync!
Vertical synchronous signal!
34
FGND!
Frame Ground!
35
ENAB!
Data enable signal (signal to settle the horizontal display position)!
36
Mode!
Data input format select, NC/High: DE mode; Low: Sync mode.!
37
VDD!
+3.3V power supply!
38
VDD!
+3.3V power supply!
39
VDD!
+3.3V power supply!
40
VDD!
+3.3V power supply!
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
15
info@display-solution.com
G085VW01 V0
6.3 Scanning Direction
The following figures show the image seen from the front view. The arrow indicates the direction of scan.
Fig. 1
Fig. 2
Fig. 1 Normal scan (Pin6, GND or NC)
Fig. 2 Reverse scan (Pin6, High)
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
16
info@display-solution.com
G085VW01 V0
6.4 Interface Timing
6.4.1 Timing Characteristics
Customers could select the input data format through controlled the NC/High or Low of Pin 36.
DE Mode
Signal
Symbol
Min.
Typ.
Max.
Unit
Remark
1/ TCLOCK
31.95
33.26
34.6
MHz
Note1
Period
TH
888
928
1138
Active
THD
TCLOCK
Note1
Blanking
THB
88
128
338
Period
TV
515
525
762
Active
TVD
TLINE
Note1
Blanking
TVB
Clock frequency (DOTCLK)
Horizontal Section
Vertical Section
800
480
35
45
282
Note: 1. Frame rate is 60 Hz at 3.3V VDD.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
17
info@display-solution.com
G085VW01 V0
Sync Mode (HV Mode)
Parameter Note
Symbol Min.
Hsync
Vsync
Typ.
Max.
Unit Note
Period
th
908
928
1088
clock Note1
Pulse width
thpw
1
48
87
clock Note1
Back porch
thb
87
40
1
clock Note1
Front porch
thfp
20
40
200
clock Note1
Display period
thd
800
800
800
clock Note1
Period
tv
517
525
712
line
Note1
Pulse width
tvpw
1
1
3
line
Note1
Back porch
tvb
31
31
29
line
Note1
Front porch
tvfp
5
13
200
line
Note1
Display period
thd
480
480
480
line
Note1
Note: 1. Frame rate is 60 Hz at 3.3V VDD.
Horizontal input timing
0
1
2
3
4
5
0
1
2
Vertical input timing
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
18
info@display-solution.com
G085VW01 V0
6.4.2 Input timing setup/ hold time
Parameter Note
Clock
Data
ENAB signal
Hsync
Vsync
Symbol
Min.
Typ.
Max.
Unit
Note
Frequency
1/Tc
31.95
33.26
34.6
MHz Note1
Clk pulse duty
Tcwh
40
50
60
%
Note1
Clk cycle time
Tcph
25
-
-
ns
Note1
Setup time
Tdsu
5
-
-
ns
Note1
Hold time
Tdhd
5
-
-
ns
Note1
Setup time
Tesu
5
-
-
ns
Note1
Hold time
Tehd
5
-
-
ns
Note1
Setup time
Thst
5
-
-
ns
Note1
Hold time
Thhd
5
-
-
ns
Note1
Setup time
Tvst
5
-
-
ns
Note1
Hold time
Tvhd
5
-
-
ns
Note1
Note 1: Frame rate is 60 Hz at 3.3V VDD.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
19
info@display-solution.com
G085VW01 V0
6.5 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as below. Interface signals are also shown in the chart. Signals from any
system shall be Hi-Z state or low level when VDD is off.
Power ON/OFF sequence timing
Value
Parameter
Units
Min.
Typ.
Max.
T1
0.5
-
10
[ms]
T2
0
-
50
[ms]
T3
200
-
-
[ms]
T4
10
-
-
[ms]
T5
10
-
-
[ms]
T6
T7
T8
T9
T10
T11
0
10
100
0
1000
16
-
50
10
-
[ms]
[ms]
[ms]
[ms]
[ms]
[ms]
The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off
the power when you plug the cable into the input connector or pull the cable out of the connector.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
20
info@display-solution.com
G085VW01 V0
7. Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of accommodating
the following signals and will be following components.
7.1 TFT LCD Signal (CN1): LCD Connector
Connector Name / Designation
Signal Connector
Manufacturer
STARTCONN or P-TWO
Connector Model Number
089H40-001100-G2-R or 196033-40041-3 or
compatible.
7.2 LED Backlight Unit (CN2): LED Driver Connector
Connector Name / Designation
Lamp Connector
Manufacturer
Entery
Connector Model Number
3808K-F05N-02R or compatible.
Mating Model Number
H208K-P05N-02B or compatible.
Pin #
Symbol
Pin Description
1
VLED
12V Power Supply
2
GND
GND
3
ENB
LED BLU on/off control
4
PWM
5
NC
Pulse width modulation for
brightness of BLU control
Don’t connection
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
21
info@display-solution.com
G085VW01 V0
7.3 LED Light Bar Input Connector (CN4):
Connector Name / Designation
Lamp Connector
Manufacturer
Entery
Connector Model Number
H208K-P02N-02B or compatible.
Mating Model Number!(CN3)
3808K-F02N-02R or compatible.
Pin #
Symbol
Pin Description
1
Vout
Positive voltage to connection LED BLU
2
FB1
Constant current feedback signal 1
8. Reliability Test Criteria
Items
Required Condition
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
4
90%,300 hours
85 ,300 hours
-30 ,300 hours
Hot Storage
85
Cold Storage
-3
Thermal Shock
Test
Shock Test
(Non-Operating)
Note
50G,20ms,Half-sine wave,( ±X, ±Y, ±Z)
Vibration Test
(Non-Operating)
1.5G, (10~200Hz, P-P)
On/off test
On/10 sec, Off/10 sec, 30,000 cycles
30 mins/axis (X, Y, Z)
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point
ESD
Note 1
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point
EMI
30-230 MHz, limit 40 dBu V/m, 230-1000 MHz, limit 47 dBu V/m
Note1: According to EN61000-4-2, ESD class B: Some performance degradation allowed. No data lost
.
Self-recoverable. No hardware failures.
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
22
info@display-solution.com
Provided by
www.display-solution.com
info@display-solution.com
9.1 LCM Front View
9. Mechanical Characteristics
G085VW01 V0
23
G085VW01 V0 rev. 1.0
9.2 LCM Rear View
SEE DETAIL A
Provided by
www.display-solution.com
info@display-solution.com
G085VW01 V0
24
G085VW01 V0 rev. 1.0
G085VW01 V0
10. Label and Packaging
10.1 Shipping Label (on the rear side of TFT-LCD display)
10.2 Carton Package
Max capacity: 30 TFT-LCD modules per carton (30pcs * 1 layer)
Max weight: 12kg per carton
Outside dimension of carton:520(L)mm*340(W)mm*250(H)mm
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
25
info@display-solution.com
G085VW01 V0
11 Safety
11.1 Sharp Edge Requirements
There will be no sharp edges or corners on the display assembly that could cause injury.
11.2 Materials
11.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used,
they will be reviewed and approved by the responsible AUO toxicologist.
11.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the
module will complete the flammability rating exception approval process.
The pRxINted circuit board will be made from material rated 94-V1 or better. The actual UL flammability
rating will be pRxINted on the pRxINted circuit board.
11.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from
being inserted backwards.
11.4 National Test Lab Requirement
The display module will satisfy all requirements for compliance to:
UL 1950, First Edition
U.S.A. Information Technology Equipment
G085VW01 V0 rev. 1.0
Provided by
www.display-solution.com
26
info@display-solution.com
Download PDF
Similar pages