Gryphon™ I GBT4100
General Purpose Handheld
Linear Imager Barcode Reader
with Bluetooth® Wireless Technology
Quick Reference Guide
Datalogic USA Inc.
959 Terry Street
Eugene, OR 97402
U.S.A.
Telephone: (541) 683-5700
Fax: (541) 345-7140
©2009-2017 Datalogic S.p.A. and/or its affiliates
An Unpublished Work - All rights reserved. No part of the contents
of this documentation or the procedures described therein may be
reproduced or transmitted in any form or by any means without
prior written permission of Datalogic USA Inc. or its subsidiaries or
affiliates (“Datalogic” or “Datalogic USA”).
Owners of Datalogic products are hereby granted a non-exclusive,
revocable license to reproduce and transmit this documentation
for the purchaser's own internal business purposes. Purchaser
shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure
that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can
acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the
Datalogic website (www.datalogic.com) or provided on appropriate
media. If you visit our website and would like to make comments
or suggestions about this or other Datalogic publications, please
let us know via the "Contact Datalogic" page
Disclaimer
Datalogic has taken reasonable measures to provide information
in this manual that is complete and accurate, however, Datalogic
reserves the right to change any specification at any time without
prior notice. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S. and
the E.U.
Gryphon is a trademark of Datalogic S.p.A. and/or its affiliates
registered in the U.S..
The Bluetooth word mark and logos are owned by Bluetooth SIG,
Inc. and any use of such marks by Datalogic Group companies is
under license. All other brand and product names may be trademarks of their respective owners.
Patents
See www.patents.datalogic.com for patent list.
See the Regulatory Addendum included with
your product for additional regulatory, safety
and legal information.
Table of Contents
END USER SOFTWARE LICENSE AGREEMENT (EULA) ............. iii
Software Product Policy ............................................................. vi
Customers Under Software Support ................................. vi
Configuring the Base Station ......................................................1
Changing the Base Station Position ......................... 1
Connecting the Base Station ......................................................4
Securing the DC Power Cord (Optional) .................... 4
Using the BC40xx™ Radio Base ........................................... 7
Radio Base LEDs ......................................................... 7
Charging the Batteries ................................................................8
Battery Safety ...................................................................... 8
Replacing the Batteries ..................................................... 11
Linking the Reader .....................................................................13
Link Datalogic RF Devices to Base.......................... 13
Link Scanner to Bluetooth Adapter in Server Mode 14
Linking to Bluetooth Adapter in HID....................... 14
System and Network Layout ............................................ 15
Typical Setup with Cradle and Host ........................ 15
Selecting the Interface Type .....................................................16
Interface Selection ............................................................. 16
Configuring the Interface ......................................... 16
Keyboard Interface ................................................... 19
Scancode Tables........................................................ 22
Country Mode ............................................................ 22
Caps Lock State......................................................... 27
Numlock..................................................................... 28
BT HID ALT Mode ...................................................... 29
Programming ..............................................................................30
Using Programming Barcodes .......................................... 30
Configure Other Settings ................................................... 30
Resetting Standard Product Defaults ............................. 30
Stand Detection ..........................................................................31
Technical Specifications ............................................................33
LED and Beeper Indications ......................................................37
Error Codes .................................................................................40
Base Station Indications ...........................................................41
Cleaning Procedure ....................................................................42
Common Cleaning Solutions ............................................. 42
Cleaning enclosure and window surfaces ....................... 43
Cleaning electrical contact surfaces ................................ 43
Datalogic Limited Factory Warranty ........................................45
Quick Reference Guide
i
Ergonomic Recommendations .................................................48
Support Through the Website ..................................................49
Keypad .........................................................................................50
ii
Gryphon™ I GBT4100
DATALOGIC IP TECH S.R.L.
END USER SOFTWARE LICENSE AGREEMENT (EULA)
FOR THE GRYPHON™ I GBT41XX
Notice to End User: There are two types of software covered by this END USER
LICENSE AGREEMENT ("EULA"): (1) The Datalogic Product you have acquired contains embedded software ("Embedded Software") which is integral to the Product's
operation; and (2) Optional Application Software provided to you on an optional
basis ("Application Software"). Embedded Software and Application Software are
collectively referred to as "Software" and are subject to the terms and conditions
contained in this EULA. Software is provided only for use with, and for authorized
end users of, the Datalogic Gryphon™ I GBT41XX ("Product").
This EULA (End User Software License Agreement) ("EULA” or "Agreement") is a
legally binding agreement governing the licensing of the Software and Documentation by Datalogic IP Tech S.r.l. and its subsidiaries and affiliates ("Datalogic") to the
entity or person who has purchased or otherwise acquired a Datalogic Product ("End
User"). For purposes of this Agreement, any software that is not Embedded Software or Application Software is software associated with a separate end-user
license agreement is licensed to you under the terms of that license agreement.
Datalogic and End User hereby agree as follows:
1. Definitions.
1.1
1.2
1.3
1.4
1.5
"Affiliate" means a business entity currently existing or later acquired that
is controlled by, or is under common control with Datalogic S.p.A.
"Documentation" means materials such as user's guides, program reference
guides, quick reference guides, manuals, or similar materials associated
with or related to the Datalogic Product, whether in printed, "online", or
other form.
"Proprietary Information" means: (a) source code, object code, software,
documentation, and any related internal design, system design, data base
design, algorithms, technology, technical data or information, implementation techniques, and trade secrets related to the Software, (b) any other
trade secrets marked appropriately or identified as proprietary or confidential, and (c) any information that End User, under the circumstances, should
recognize as confidential. Proprietary Information does not include any
information that the receiving party can establish was (1) in the public
domain, (2) already in the receiving party's possession or rightfully known
prior to receipt, (3) rightfully learned from a third party not in violation of
any other's proprietary rights, or (4) independently developed without
access to Proprietary Information.
"Datalogic Product" means the Datalogic Gryphon™ series scanner product,
including all embedded Software in and all Documentation related to such
product, which has been purchased or otherwise acquired by End User,
whether obtained directly or indirectly from Datalogic.
"Software" means any software or computer programs of Datalogic or its
third party licensors in machine readable form which is embedded in the
Datalogic Product, whether obtained directly or indirectly from Datalogic,
including any replacement, update, upgrade, enhancement or modification.
2. Scope Of License Granted.
2.1
2.2
Datalogic grants to End User personal a non-exclusive, non-transferable,
perpetual license to use the Software, solely on the Datalogic Product in
which it is embedded ("designated Datalogic Product"), in machine-readable
form only, solely for End User's internal business purposes. This Agreement
does not convey ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the third party from whom Datalogic has obtained a licensed right. As used in this Agreement, the term
"purchase" or its equivalents when applied to the Software shall mean
"acquire under license." End User is not entitled to receipt or use of the
source code to any Software.
End User shall not copy, modify, decompile, disassemble, reverse engineer,
or otherwise reproduce or remanufacture the Software, whether modified
or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than as expressly provided in this Agreement, without
Datalogic's prior written consent.
Quick Reference Guide
iii
3. Transfers, Support.
3.1
3.2
3.3
Any copying, installing, reproduction, remanufacture, reverse engineering,
electronic transfer, or other use of the Software on other than the designated Datalogic Product will be a material breach of this Agreement. However, Datalogic may elect not to terminate this Agreement or the granted
licenses, but instead may elect to notify End User that End User is deemed
to have ordered and accepted a license for each breaching use. End User
shall pay Datalogic the applicable list price for such licenses as of the date
of such breach.
End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Datalogic Product to any third party unless such third
party agrees with Datalogic in writing to be bound by the terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent
such agreement shall be null and void.
End User may obtain support for Software from Datalogic at Datalogic's
standard support fees and under Datalogic's standard support terms and
conditions in effect at the time the support is requested.
4. Intellectual Property.
End User acknowledges that the Software comprises valuable trade secrets of
Datalogic or Datalogic's third party licensors and that the Software is protected by
United States copyright law and trade secret law, and by all applicable international
intellectual property laws and treaty provisions. The license set forth in this Agreement does not transfer to End User any ownership of Datalogic's or its third party
licensors' copyrights, patents, trademarks, service marks, trade secrets, or other
intellectual property rights and End User shall have no right to commence any legal
actions to obtain such rights. End User shall not remove, modify, or take any other
action that would obscure any copyright, trademark, patent marking, or other intellectual property notices contained in or on the Datalogic Product.
5. Proprietary Information.
5.1
5.2
5.3
End User acknowledges that Proprietary Information is the confidential,
proprietary, and trade secret property of Datalogic and Datalogic's third
party licensors and End User acquires no right or interest in any Proprietary
Information.
End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic or its third party licensors to any person
other than End User's authorized employees or agents who are under confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction with use of the Datalogic Product exclusively
for End User's internal business purposes. End User shall take steps to protect the Proprietary Information no less securely than if it were End User's
own intellectual property.
The provisions of this Proprietary Information Section shall survive and
continue for five (5) years after the termination of this Agreement.
6. Limited Warranty.
6.1
6.2
iv
Datalogic warrants that, under normal use and operation, the Datalogic
Product will conform substantially to the applicable Documentation for the
period specified in the Documentation. During this period, for all reproducible nonconformities for which Datalogic has been given written notice,
Datalogic will use commercially reasonable efforts to remedy nonconformities verified by Datalogic. End User agrees to supply Datalogic with all reasonably requested information and assistance necessary to help Datalogic
in remedying such nonconformities. For all defects reported to Datalogic
within the warranty period, Datalogic's liability is limited to providing End
User with one copy of corrections or responding to End User's problem
reports according to Datalogic's standard assistance practices. Datalogic
does not warrant that the product will meet End User's requirements or
that use of the product will be uninterrupted or error free, or that Datalogic's remedial efforts will correct any nonconformance. This limited warranty does not cover any product that have been subjected to damage or
abuse, whether intentionally, accidentally, or by neglect, or to unauthorized
repair or unauthorized installation, and shall be void if End User modifies
the product, uses the product in any manner other than as established in
the Documentation, or if End User breaches any of the provisions of this
Agreement.
EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS
PROVIDED "AS IS" AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND,
EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Gryphon™ I GBT4100
7. Infringement.
To the maximum extent permitted by law, End User agrees to defend,
indemnify and hold harmless Datalogic, its affiliates and their respective directors, officers, employees and agents from and against any
and all claims, actions, suits or proceedings, as well as any and all
losses, liabilities, damages, costs and expenses (including reasonable
attorney’s fees) arising out of or accruing from (a) the End User’s use of
Software, (b) any application the End User develops on the Software
that infringes any Intellectual Property Rights of any person or
defames any person or violates their rights of publicity or privacy, and
(c) any non-compliance by the End User of this Agreement.
8. Limitation Of Liability.
DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY
OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY,
WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR
FEE PAID BY END USER FOR THE DATALOGIC PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY FOR
LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY
OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE,
EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use.
9.1
9.2
Use, duplication, or disclosure of the Software by the U.S. Government is
subject to the restrictions for computer software developed at private
expense as set forth in the U.S. Federal Acquisition Regulations at FAR
52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer
Software clause at DFARS 252.227-7013(c)(1)(ii), whichever is applicable.
If End User is using the Datalogic Product outside of the United States, End
User must comply with the applicable local laws of the country in which the
Datalogic Product is used, with U.S. export control laws, and with the
English language version of this Agreement. The provisions of the "United
Nations Convention on International Sale of Goods" shall not apply to this
Agreement.
10. Termination.
10.1
10.2
Either party may terminate this Agreement or any license granted under
this Agreement at any time upon written notice if the other party breaches
any provision of this Agreement.
Upon termination of this Agreement, End User immediately shall cease
using any nonembedded software and shall return to Datalogic or destroy
all non-embedded software covered by this Agreement, and shall furnish
Datalogic with a certificate of compliance with this provision signed by an
officer or authorized representative of End User. For embedded software,
End User agrees to sign a waiver prepared by Datalogic concerning further
use of the embedded Software. End User's resumed or continued use of the
embedded Software after termination shall constitute End User's agreement to be bound by the terms and conditions of this Agreement for such
use.
11. General Provisions.
11.1
11.2
11.3
11.4
Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to the licensing of the Software and
supersedes all prior or contemporaneous agreements, written or oral,
between the parties concerning the licensing of the Software. This Agreement may not be changed, amended, or modified except by written document signed by Datalogic.
Notice. All notices required or authorized under this Agreement shall be
given in writing, and shall be effective when received, with evidence of
receipt. Notices to Datalogic shall be sent to the attention of Datalogic IP
Tech S.r.l., Legal & IP Department, Via San Vitalino 13, 40012 Calderara di
Reno (Bologna), Italy or such other address as may be specified by Datalogic
in writing.
Waiver. A party's failure to enforce any of the terms and conditions of this
Agreement shall not prevent the party's later enforcement of such terms
and conditions.
Governing Law; Venue: Both parties agree to the application of the laws of
the country in which End User obtained the license to govern, interpret, and
Quick Reference Guide
v
Software Product Policy
11.5
enforce all of End User’s and Datalogic’s respective rights, duties, and obligations arising from, or relating in any manner to, the subject matter of this
Agreement, without regard to conflict of law principles. The United Nations
Convention on Contracts for the International Sale of Goods does not apply.
All rights, duties, and obligations are subject to the courts of the country in
which End User obtained the license. For licenses granted by Licensee who
operates in the countries specified below, the following terms applies.
For Americas.
This Agreement is governed by the laws of the State of Oregon. This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without
regard to the rules governing conflicts of law. The state or federal courts of
the State of Oregon located in either Multnomah or Lane counties shall
have exclusive jurisdiction over all matters regarding this Agreement,
except that Datalogic shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in
which End User resides, or in which any of End User's assets are located. In
the event an action is brought to enforce the terms and conditions of this
Agreement, the prevailing party shall be entitled to reasonable attorneys’
fees, both at trial and on appeal.
For Europe, Middle East and Africa
This Agreement is governed by the laws of Italy. This Agreement and the
rights of the parties hereunder shall be governed by and construed in
accordance with the laws of Italy, without regard to the rules governing
conflicts of law. Italian Court of Bologna shall have exclusive jurisdiction
over all matters regarding this Agreement, except that Datalogic shall have
the right, at its absolute discretion, to initiate proceedings in the courts of
any other state, country, or territory in which End User resides, or in which
any of End User's assets are located. In the event an action is brought to
enforce the terms and conditions of this Agreement, the prevailing party
shall be entitled to reasonable attorneys’ fees, both at trial and on appeal.
For Asia- Pacific Countries
This Agreement is governed by the laws of the State of Hong Kong. This
Agreement and the rights of the parties hereunder shall be governed by
and construed in accordance with the laws of the State of Hong Kong without regard to the rules governing conflicts of law. The Court of Hong Kong
shall have exclusive jurisdiction over all matters regarding this Agreement,
except that Datalogic shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in
which End User resides, or in which any of End User's assets are located. In
the event an action is brought to enforce the terms and conditions of this
Agreement, the prevailing party shall be entitled to reasonable attorneys’
fees, both at trial and on appeal.
Attorneys' Fees. In the event an action is brought to enforce the terms and
conditions of this Agreement, the prevailing party shall be entitled to reasonable attorneys' fees, both at trial and on appeal.
- END -
Software Product Policy
Datalogic reserves the right to ship its products with the latest version
of software/firmware available. This provides our customers with the
very latest in Datalogic software technology.
The only exception to this policy is when the buyer has a signed contract
with Datalogic that clearly defines the terms and conditions for making
software/firmware changes in products shipped to the buyer.
Customers Under Software Support
To arrange for a Software Maintenance and Support Agreement please
contact your Datalogic sales person.
vi
Gryphon™ I GBT4100
Setting Up the Reader
Follow the steps below to connect and get your reader up
and communicating with its host.
1. Configure the Base Station starting on this
page.
2.
Charge the Batteries (see page 8).
3.
Link to the Base Station (see page 13).
4.
Select the Interface Type (see page 16).
5.
Configure the Reader starting on page 30
(optional, depends on settings needed).
Configuring the Base Station
The base charger/station may be configured in desk
application to hold the reader in two different positions,
either a horizontal or standing position, in order to provide
the most comfortable use depending on needs.
Standing
Horizontal
Changing the Base Station Position
The base station is configured by installing one of two
sets of mechanical parts that come with the cordless kit.
The default mounts (shown below) provide three options:
vertical (wall) mounting, standing (45°), or horizontal
mounting with a higher mechanical retention of the scanner. Use the other mounts only for horizontal mounting,
with lower retention of the scanner. The different parts
may be interchanged to customize retention preferences.
Quick Reference Guide
1
Configuring the Base Station
A tool such as a rigid pen or a flat screwdriver
can be used to change the mounts. Do not
allow it to touch the contacts.
1.
Insert the appropriate parts for the desired base
station position, as shown below.
Standing,
Horizontal
or Vertical
2.
Horizontal
Only
Using your thumbs, push open the plastic tabs
on the bottom of the base to free the wing holders.
Tab
Tab
To ensure best contact and performance, do
not intermix the parts of the two different
mount sets.
2
Gryphon™ I GBT4100
Configuring the Base Station
3.
The stand can now be repositioned in either
horizontal or standing position.
Horizontal
Standing
Quick Reference Guide
3
Connecting the Base Station
Connecting the Base Station
Figure 1 shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before
connection and consult the manual for that equipment (if
necessary) before proceeding. Connect the interface cable
before applying power to the Base Station.
Gryphon BT can also be Powered by the Terminal. When powered by the Terminal, the battery
charger is automatically set as Slow charge.
For some specific interfaces or hosts or lengths
of cable, the use of an external power supply
may be recommended for full recharging capability (see "Technical Specifications" on page 33
for more details)
Base Station Connection and Routing — Fully insert the
Power Cable and Interface (I/F) Cable connectors into their
respective ports in the underside of the Base Station (see
Figure 1). Then connect to an AC Adapter, and plug the AC
power cord into the (wall) outlet.
Figure 1. Connecting the Base Station
Wall plug
Connector
I/F Cable
AC/DC
Adapter
DC Power
Cord
Base
Station
Securing the DC Power Cord (Optional)
The DC power cord for the adapter can be secured to the
bottom of the base in order to maximize the mechanical
retention of the cable itself. The routing of the power cord
can be changed to accommodate the base station posi-
4
Gryphon™ I GBT4100
tioning: horizontal, stand or wall mounting. The cables can
be looped around to the front of the Base Station, or fed
directly out the back of the Base Station, as shown in Figure 2 on page 5.
Figure 2. Options for routing the DC cord
Please refer to the arrows depicted on the bottom of the
base when placing the cables, detailed in Figure 3.
Figure 3. Arrows showing routing
Quick Reference Guide
5
Connecting the Base Station
Host Connection — Verify before connection that the
reader’s cable type is compatible with your host equipment.
The Gryphon I GBT4100 can be set up to require a
PIN code when connecting to the host. If you are
adding new equipment to a system that uses a
custom security PIN, please see the PRG for
information before proceeding.
Most connections plug directly into the host device as
shown in Figure 4. Keyboard Wedge interface cables have
a ‘Y’ connection where its female end mates with the male
end of the cable from the keyboard, and the remaining end
at the keyboard port on the terminal/PC.
B
Figure 4. Connecting to the Host
Wa
Ke W
nd
US
or...
yb
ed oard
g
or... e
M
or...
IB
Power Connection — Plug the AC Adapter into an approved
AC wall socket with the cable facing downwards (as
shown in Figure 1) to prevent undue strain on the socket.
Disconnecting the Cable — To detach the cable, insert a
paper clip or similar object into the hole on the base, as
shown in Figure 5.
Figure 5. Disconnecting the Cable
Insert
Paper Clip
6
Gryphon™ I GBT4100
Connecting the Base Station
Using the BC40xx™ Radio Base
Radio Base LEDs
LEDs on the Gryphon I Base provide information about the
Bases well as battery charging status, as shown in
Figure 6.
Figure 6. Gryphon I Base LEDs
YELLOW LED
BUTTON
RED LED —
GREEN LED
The following table describes the significance of each LED.
Table 1. Radio Base LEDs
LED
STATUS
Power on /
Data
Yellow On = Base is powered
Yellow Blinking = Base receives data
and
commands from the Host or the
Reader.
Charging
Red On = the Battery is charging.
Charge completed
Green On = the Battery is completely
charged.
Charging +
Charge completed
Red and Green Blinking together =
the Reader is not correctly placed
onto the Base.
The button can be used to force device connection via the
Datalogic Aladdin Software tool, and for paging the scanner when it is activated. Refer to the Gryphon I Product
Reference Guide (PRG) for a more detailed explanation.
Quick Reference Guide
7
Charging the Batteries
Charging the Batteries
To charge the battery, simply insert the Gryphon into the
base. When the scanner is fully seated in the cradle, it will
sound a “chirp” to indicate that the cradle has detected
the scanner connection.
The LEDs on the base (shown in Table 1) will indicate the
status of the battery.
Before using the Battery, read “Battery
Safety” in the following section. Datalogic
recommends annual replacement of
rechargeable battery packs to ensure maximum performance.
Battery Safety
To install, charge and/or do any other action on the battery, fo low the instructions in this manual.
WARNING
8
Do not discharge the battery using any
device except for the scanner. When the
battery is used in devices other than the
designated product, it may damage the battery or reduce its life expectancy. If the
device causes an abnormal current to flow,
it may cause the battery to become hot,
explode or ignite and cause serious injury.
Lithium-ion battery packs may get hot,
explode or ignite and cause serious injury if
exposed to abusive conditions. Be sure to
follow the safety warnings listed on the following page.
Gryphon™ I GBT4100
Charging the Batteries
•
Do not place the battery pack in fire or
heat.
•
Do not connect the positive terminal
and negative terminal of the battery
pack to each other with any metal
object (such as wire).
•
Do not carry or store the battery pack
together with metal objects.
•
Do not pierce the battery pack with
nails, strike it with a hammer, step on it
or otherwise subject it to strong
impacts or shocks.
•
Do not solder directly onto the battery
pack.
•
Do not expose the battery pack to liquids, or allow the battery to get wet.
•
Do not apply voltages to the battery
pack contacts.
WARNING
WARNING
CAUTION
CAUTION
In the event the battery pack leaks and the
fluid gets into your eye, do not rub the eye.
Rinse well with water and immediately
seek medical care. If left untreated, the battery fluid could cause damage to the eye.
Always charge the battery at 32° – 104°F (0°
- 40°C) temperature range.
Use only the authorized power supplies, battery pack, chargers, and docks supplied by
your Datalogic reseller. The use of any other
power supplies can damage the device and
void your warranty.
Do not disassemble or modify the battery.
The battery contains safety and protection
devices, which, if damaged, may cause the
battery to generate heat, explode or ignite.
Quick Reference Guide
9
Charging the Batteries
CAUTION
CAUTION
Do not place the battery in or near fire, on
stoves or other high temperature locations.
Do not place the battery in direct sunlight, or
use or store the battery inside cars in hot
weather. Doing so may cause the battery to
generate heat, explode or ignite. Using the
battery in this manner may also result in a
loss of performance and a shortened life
expectancy.
Do not place the battery in microwave ovens,
high-pressure containers or on induction
cookware.
Immediately discontinue use of the battery
if, while using, charging or storing the battery, the battery emits an unusual smell,
feels hot, changes color or shape, or appears
abnormal in any other way.
Do not replace the battery pack when the
device is turned on.
Do not remove or damage the battery pack’s
label.
Do not use the battery pack if it is damaged
in any part.
Battery pack usage by children should be
supervised.
As with other types of batteries, Lithium-Ion (LI) batteries
will lose capacity over time. Capacity deterioration is
noticeable after one year of service whether the battery is
in use or not. It is difficult to precisely predict the finite life
of a LI battery, but cell manufacturers rate them at 500
charge cycles. In other words, the batteries should be
expected to take 500 full discharge / charge cycles before
needing replacement. This number is higher if partial discharging / recharging is adhered to rather than full / deep
discharging.
CAUTION
10
Storage of batteries for long time at fully charged
status or at fully discharged status should be
avoided.
Gryphon™ I GBT4100
Charging the Batteries
Only in case of long storage, to avoid deep discharge of the battery it is recommended to partially recharge the battery every three months to
keep the charge status at a medium level.
CAUTION
As a reference, run a fast recharge for 20 minutes
every three months on unused products to avoid
any performance deterioration of the cell.
The useful life of LI batteries depends on usage and number of charges, etc., after which they should be removed
from service, especially in mission critical applications. Do
not continue to use a battery showing excessive loss of
capacity, it should be properly recycled / disposed of and
replaced.
Collect and recycle waste batteries separately from the
device in comply with European Directive 2006/66/EC,
2011/65/EU, 2002/96/EC, 2012/19/EU, and subsequent
modifications, US and China regulatory and others laws
and regulations about the environment.
Replacing the Batteries
Before proceeding, read “Battery Safety” on
the preceding pages. Datalogic recommends
annual replacement of rechargeable battery
packs to ensure maximum performance.
Use the following procedure to change the reader’s battery:
1. With a screwdriver, unscrew the battery cover
screw.
Quick Reference Guide
11
Charging the Batteries
2.
Unplug the three screws securing the battery
holder, and unplug the white connector.
Screw
Connector
Screw
3.
Screw
Carefully lift out the gold contacts circuit, and
remove the battery holder while letting the
white connector pass through the hole in the
battery holder (as shown below).
Pass-through
hole
Gold
contacts
circuit
4.
12
Remove the old battery from its place (if present), and insert the new battery in the same
position.
Gryphon™ I GBT4100
Linking the Reader
5.
Replace the battery holder, plug in the connector
and return the contacts circuit to its previous
location.
When inserting the new battery into the handle, take care to position the battery and the
connector as shown.
6.
Insert the cover in the handle and screw it back
into place.
Linking the Reader
Link Datalogic RF Devices to Base
For RF devices, before configuring the interface it is necessary to link the handheld with the base.
To link the handheld and the base, press the trigger to
wake it and place it on the base. If the reader was previously linked to another base, you must first scan the
Unlink barcode before re-linking to the new base.
Unlink
Quick Reference Guide
13
Linking the Reader
Link Scanner to Bluetooth Adapter in Server
Mode
1.
Install any drivers provided with the Bluetooth
adapter.
2.
Scan the Enable RF Link to Server label below to
make the scanner visible to the host computer.
3.
Use the host computer’s Bluetooth manager to
“Discover new devices” and select "Datalogic
Scanner." If you receive an error message, it may
be necessary to disable security on the device.
4.
Use an RS-232 terminal program to see incoming data on the port designated by the computer's Bluetooth manager.
Enable RF Link to Server
The Gryphon I GBT4100 can be set up to
require a PIN code when connecting. If you
want to set up a PIN, or when adding new
equipment to a system that uses a custom
security PIN, please see the PRG for information.
Linking to Bluetooth Adapter in HID
14
1.
Install any drivers provided with the Bluetooth
adapter.
2.
Scan the Link to a PC in HID bar code below to
make the scanner visible to the host computer.
3.
Use the host computer's Bluetooth manager to
"Discover new devices" and select "Datalogic
Scanner." If you receive an error message, it may
be necessary to disable security on the device.
4.
Select "connect" on the PC to link the reader to
the PC. Use a text editor to see incoming data
from the reader.
Gryphon™ I GBT4100
Linking the Reader
Link to a PC in HID
Some Bluetooth drivers on the Host (such as
WIDCOMM and BlueSoleil 8) require a Variable
PIN Code. When attempting connection in HID
Profile, the application presents a window
that includes a PIN Code which is to be input
using the GBT4100. Please read the barcode
"Use Variable PIN Code" and restart the
sequence from step 2 above.
Use Variable PIN Code
When you hear the beep and see the Green LED blinking
indicating the reader is waiting for an alphanumeric entry,
enter the variable PIN Code by scanning the bar code(s)
corresponding with the required PIN Code from
Keypad, starting on page 1-50.
System and Network Layout
Typical Setup with Cradle and Host
Figure 7. Reader Layout
Quick Reference Guide
15
Selecting the Interface Type
Selecting the Interface Type
Upon completing the physical connection between the
reader and its host, proceed directly to Interface Selection
on page 16 for information and programming for the
interface type the reader is connected to (for example: RS232, Keyboard Wedge, USB, etc.) and scan the appropriate
barcode to select your system’s correct interface type.
Interface Selection
Each reader model will support one of the following sets
of host interfaces:
General Purpose Models — RS-232, RS-232 OPOS, USB, Keyboard Wedge, Wand.
Retail Point of Sale Models — RS-232, RS-232 OPOS, USB,
IBM 46XX.
Information and programming options for each interface
type are provided in this section.
Configuring the Interface
Scan the programming barcode which selects the appropriate interface type matching the system the reader will
be connected to.
If you need to customize additional settings and features
associated with that interface, proceed to the corresponding chapter in the Gryphon™ I PRG.
Unlike some other programming features and
options, interface selections require that you
scan only one programming barcode label. DO
NOT scan an ENTER/EXIT barcode prior to
scanning an interface selection barcode.
Some interfaces require the scanner to start in
the disabled state when powered up. If additional scanner configuration is desired while
in this state, pull the trigger and hold for 5
seconds. The scanner will change to a state
that allows programming with barcodes.
16
Gryphon™ I GBT4100
Selecting the Interface Type
RS-232
RS-232 standard interface
Select RS232-STD
RS-232 Wincor-Nixdorf
Select RS232-WN
RS-232 for use with OPOS/UPOS/JavaPOS
Select RS-232 OPOS
USB Com to simulate RS-232 standard interface
Select USB-COM-STDa
Quick Reference Guide
17
Selecting the Interface Type
IBM
IBM-46xx Port 5B reader interface
Select IBM-P5B
IBM-46xx Port 9B reader interface
Select IBM-P9B
USB-OEM
USB-OEM
(can be used for OPOS/UPOS/JavaPOS)
Select USB-OEM
a. Download the correct USB Com driver from www.datalogic.com
18
Gryphon™ I GBT4100
Selecting the Interface Type
Keyboard Interface
Use the programming barcodes to select options for
USB Keyboard and Wedge Interfaces.
KEYBOARD
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/
Standard Key Encoding
Select KBD-AT
Keyboard Wedge for IBM AT PS2 with standard key encoding
but without external keyboard
Select KBD-AT-NK
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Alternate Key
Select KBD-AT-ALT
Keyboard Wedge for IBM AT PS2 with alternate key encoding
but without external keyboard
Select KBD-AT-ALT-NK
Quick Reference Guide
19
Selecting the Interface Type
KEYBOARD (continued)
PC/XT w/Standard Key Encoding
Select KBD-XT
Keyboard Wedge for IBM Terminal 3153
Select KBD-IBM-3153
Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx
make only keyboard
Select KBD-IBM-M
Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx
make break keyboard
Select KBD-IBM-MB
Keyboard Wedge for DIGITAL Terminals
VT2xx, VT3xx, VT4xx
Select KBD-DIG-VT
20
Gryphon™ I GBT4100
Selecting the Interface Type
KEYBOARD (continued)
USB Keyboard with standard key encoding
Select USB Keyboard
USB Keyboard with alternate key encoding
Select USB Alternate Keyboard
USB Keyboard for Apple computers
Select USB-KBD-APPLE
WAND EMULATION
Wand Emulation
Select WAND
Quick Reference Guide
21
Selecting the Interface Type
Scancode Tables
Reference the Gryphon™ I PRG for information about control character emulation which applies to keyboard interfaces.
Country Mode
This feature specifies the country/language supported by
the keyboard. Only the following interfaces support ALL
Country Modes.
•
USB Keyboard (without alternate key encoding)
•
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 &
95 w/Std Key Encoding
•
Keyboard Wedge for IBM AT PS2 with standard
key encoding but without external keyboard
•
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 &
95 without Alternate Key
•
Keyboard Wedge for IBM AT PS2 without alternate key encoding but without external keyboard
•
Bluetooth HID Profile
All other interfaces support ONLY the following Country
Modes: U.S., Belgium, Britain, France, Germany, Italy, Spain,
Sweden.
22
Gryphon™ I GBT4100
Selecting the Interface Type
COUNTRY MODE
ENTER/EXIT PROGRAMMING MODE
Country Mode = U.S.
Country Mode = Belgium
Country Mode = Britain
Country Mode = Croatia*
Country Mode = Czech Republic*
*Supports only the interfaces listed in the Country Mode feature description
Quick Reference Guide
23
Selecting the Interface Type
COUNTRY MODE (continued)
Country Mode = Denmark*
Country Mode = France
Country Mode = French Canadian
Country Mode = Germany
Country Mode = Hungary*
Country Mode = Italy
*Supports only the interfaces listed in the Country Mode feature description
24
Gryphon™ I GBT4100
Selecting the Interface Type
COUNTRY MODE (continued)
Country Mode = Japanese 106-key*
Country Mode = Lithuanian
Country Mode = Norway*
Country Mode = Poland*
Country Mode = Portugal*
*Supports only the interfaces listed in the Country Mode feature description
Quick Reference Guide
25
Selecting the Interface Type
COUNTRY MODE (continued)
Country Mode = Romania*
Country Mode = Slovakia*
Country Mode = Spain
Country Mode = Sweden
Country Mode = Switzerland*
*Supports only the interfaces listed in the Country Mode feature description
26
Gryphon™ I GBT4100
Selecting the Interface Type
Caps Lock State
This option specifies the format in which the reader sends
character data. This applies to keyboard wedge interface
and Bluetooth HID Profile. It does not apply when an
alternate key encoding keyboard is selected.
ENTER/EXIT PROGRAMMING MODE
Caps Lock State = Caps Lock OFF
Caps Lock State = Caps Lock ON
Caps Lock State = AUTO Caps Lock Enable
Quick Reference Guide
27
Selecting the Interface Type
Numlock
This option specifies the setting of the Numbers Lock
(Numlock) key while in keyboard wedge interface. This
only applies to alternate key encoding interfaces. It does
not apply to USB keyboard.
ENTER/EXIT PROGRAMMING MODE
Numlock = Numlock key unchanged
Numlock = Numlock key toggled
28
Gryphon™ I GBT4100
Selecting the Interface Type
BT HID ALT Mode
This feature Enables/Disables the ability to transmit correctly a label content to the host regardless the BT HID
Country Mode selected, when BT HID profile is configured.
ENTER/EXIT PROGRAMMING MODE
HID ALT Mode = Disable
HID ALT Mode = Enable
Quick Reference Guide
29
Programming
Programming
The reader is factory-configured with a set of standard
default features. After scanning the interface barcode
from the Interfaces section, you can select other options
and customize your reader through use of the instructions
and programming barcodes available in the Gryphon™ I
Product Reference Guide (PRG). Check the corresponding
features section for your interface, and also the Data Editing and Symbologies chapters of the PRG.
Using Programming Barcodes
This manual contains barcodes which allow you to reconfigure your reader. Some programming barcode labels, like
the "Standard Product Default Settings" on page 31,
require only the scan of that single label to enact the
change.
Other barcodes require the reader to be placed in Programming Mode prior to scanning them. Scan an ENTER/
EXIT barcode once to enter Programming Mode; scan the
desired parameter settings; scan the ENTER/EXIT barcode
again to accept your changes, which exits Programming
Mode and returns the reader to normal operation.
Configure Other Settings
Additional programming barcodes are available in the Gryphon™ I PRG to allow for customizing programming features. If your installation requires different programming
than the standard factory default settings, refer to the
PRG.
Resetting Standard Product Defaults
Reference the PRG for a listing of standard factory settings. If you aren’t sure what programming options are in
your reader, or you’ve changed some options and want the
factory settings restored, scan the Standard Product Default
Settings barcode below to copy the factory configuration
for the currently active interface to the current configuration.
Factory defaults are based on the interface
type. Configure the reader for the correct interface before scanning this label.
30
Gryphon™ I GBT4100
Stand Detection
Standard Product Default Settings
Stand Detection
The following labels control how the scanner behaves
when it is placed into a cradle or stand that has the hardware to support automatic stand detection.
Switch to Stand Mode — Automatically switches the scanner to Stand Mode when the scanner is placed in the
stand.
Switch to Flashing — Automatically switches the scanner to
Flash Mode when the scanner is placed in the stand.
Switch to Always On — Automatically switches the scanner
to Always On mode when the scanner is placed in the
stand.
Ignore Autorecognition — Disables mode switching when
the scanner is placed in a stand.
Switch to Stand Mode
Switch to Flashing
Quick Reference Guide
31
Stand Detection
Switch to Always On
Ignore Autorecognition
32
Gryphon™ I GBT4100
Technical Specifications
Technical Specifications
The following table contains Physical and Performance
Characteristics, User Environment and Regulatory information.
Item
Description
Physical Characteristics
Color
White/Gray
Black/Gray
Dimensions
Height 7.1”/181 mm
Length 3.9”/100 mm
Width 2.8”/71 mm
Weight (without
cable)
Approximately
8.7 ounces/246 g (reader with display)
8.7 ounces/246 g (base charger)
Electrical Characteristics
Battery Type
Typical charge time
for full charge from
full discharge
Li-Ion battery pack
4 hours with 12V external power supply
adaptera
Max 22 hours with Host power
(in this case no supply adapter is needed)a
Operating autonomy
(continuous reading)
30,000 reads
(typical)
Cradle consumption
and DC input supply
range
Volt 4.75-14 VDC; Power <8Wb;
Imax 500mA when in host/bus powered
modeb.
Performance Characteristics
Light Source
LEDs
Roll (Tilt) Tolerance
± 35° from normal
Pitch Tolerance
± 65°
Quick Reference Guide
33
Technical Specifications
Item
Description
Skew (Yaw) Tolerance
± 65°
Field of View
10” (25.4cm) wide at 12.5” (31.8cm) from
the reader
Depth of Field (Typical)c
3 mil – 2.9” to 4.7” (7.5cm to 12cm)
13 mild – 1.2” to 23.6” (3cm to 60cm)
20 mil – 1.2” to 31.5” (3cm to 80cm)
Minimum Element
Width
3 mil
Print Contrast Minimum
15% minimum reflectance
Decode Capability
UPC/EAN/JAN, P2 /P5 add-ons; Code 39;
Italian Pharmacode 39; Code 128; C128
ISBT; Code 128 add-ons; I 2 of 5; Standard
2 of 5; Code 11;Codabar; EAN 128; Code 93;
MSI; GS1 DataBar™ Omnidirectional, GS1
DataBar™ Limited, GS1 DataBar™
Expanded; Code4, Code5.
Interfaces Supportedd
RS-232 Std, RS-232 Wincor-Nixdorf, RS232 OPOS, IBM 46xx (ports5B and 9B), USB
Com Std., USB Keyboard, USB Alternate
Keyboard, USB OEM, Keyboard Wedge (AT
with or w/o Alternate Key, IBM AT PS2
with or w/o Alternate Key, PC-XT, IBM
3153, IBM Terminals 31xx, 32xx,34xx, 37xx
make only and make break keyboard, Digital Terminals VT2x, VT3xx, VT4xx, and
Apple) and Wand Emulation.
User Environment
Operating Temperature
32° to 122° F (0° to 50° C)
Charging Temperature
32° to 104° F (0° to 40° C)
34
Gryphon™ I GBT4100
Technical Specifications
Item
Description
Storage Temperature
-4° to 158° F (-20° to 70° C)
Humidity
Operating: 5% to 90% relative humidity,
non-condensing
Drop Specifications
Scanner withstands 18 drops from 1.8
meters
(5.9 feet) to concrete
Ambient Light
Immunity
Up to 100,000 Lux
Contaminants
Spray/rain Dust/
particulates
IEC 529-IP52 (scanner only)
ESD Level
16 KV
a. Charge Times are much lower when battery is within daily typical operating condition.
b. Typical input current measured under factory default configuration.
c. 13 mils DOF based on EAN. All others are Code 39. All labels grade A,
typical environmental light, 20°C, label inclination 10°
d. See "Interface Selection" on page 16 for a listing of available interface
sets by model type.
Quick Reference Guide
35
Technical Specifications
Item
Description
Regulatory
See the Regulatory Addendum for details.
Radio Features
Frequency Range
2400 to 2483.5 MHz
Range (in open air)
30 m
36
Gryphon™ I GBT4100
LED and Beeper Indications
LED and Beeper Indications
The reader’s beeper sounds and its LED illuminates to
indicate various functions or errors on the reader. An
optional “Green Spot” also performs useful functions. The
following tables list these indications. One exception to
the behaviors listed in the tables is that the reader’s functions are programmable, and may or may not be turned
on. For example, certain indications such as the power-up
beep can be disabled using programming barcode labels.
INDICATION
DESCRIPTIO
N
The reader is in
Power-up Beep the process of
powering-up.
LED
BEEPER
N/A
Reader beeps
four times at
highest frequency and volume upon
power-up.
Good Read
Beep
LED behavior
for this indication is configuA label has been rable via the
feature “Good
successfully
scanned by the Read: When to
Indicate”
reader.
(see the PRG
for information.)
The reader will
beep once at
current frequency, volume,
mono/bi-tonal
setting and
duration upon a
successful label
scan.
ROM Failure
There is an error
in the reader's
software/programming
Flashes
Reader sounds
one error beep
at highest volume.
Limited Scanning Label
Read
Indicates that a
host connection
is not established when the
IBM or USB
interface is
enabled.
N/A
Reader 'chirps'
six times at the
highest frequency and current volume.
Quick Reference Guide
37
LED and Beeper Indications
INDICATION
DESCRIPTIO
N
Reader Active
Mode
The reader is
active and ready
to scan.
Reader
Disabled
The reader has
The LED blinks
been disabled by
continuously
the host.
N/A
Green Spot is
on continuously
While in Stand
Mode or Trigger
Stand Mode the
green spot shall
be on while in
stand watch
state.
N/A
N/A
Green Spota
flashes
momentarily
Upon successful read of a
label, the software shall turn
the green spot
on for the time
specified by the
configured
value.
N/A
N/A
LED
BEEPER
The LED is lit
steadilya
N/A
Programming Mode - The following indications ONLY occur
when the reader is in Programming Mode.
Label Program- A valid programLED blinks
ming label has
ming Mode
continuously
been scanned.
Entry
Reader sounds
four low frequency beeps.
Label ProgramA label has been
ming Mode
rejected.
Rejection of
Label
Reader sounds
three times at
lowest frequency and current volume.
38
N/A
Gryphon™ I GBT4100
LED and Beeper Indications
INDICATION
DESCRIPTIO
N
In cases where
multiple labels
must be
scanned to proLabel Programgram one feaming Mode
ture, this
Acceptance of
indication
Partial Label
acknowledges
each portion as
it is successfully scanned.
Configuration
option(s) have
been successLabel Programfully proming Mode
grammed via
Acceptance of
labels and the
Programming
reader has
exited Programming Mode.
Label ProgramCancel label has
ming Mode
been scanned.
Cancel Item
Entry
LED
BEEPER
N/A
Reader sounds
one short beep
at highest frequency and current volume.
N/A
Reader sounds
one high frequency beep
and 4 low frequency beeps
followed by
reset beeps.
N/A
Reader sounds
two times at
low frequency
and current volume.
a. Except when in sleep mode or when a Good Read LED Duration other than
00 is selected
Quick Reference Guide
39
Error Codes
Error Codes
Upon startup, if the reader sounds a long tone, this means
the reader has not passed its automatic Selftest and has
entered FRU (Field Replaceable Unit) isolation mode. If the
reader is reset, the sequence will be repeated. The following table describes the LED flashes/beep codes associated with an error found.
NUMBER
OF LED
FLASHES
/
BEEPS
40
ERROR
1
Configuration
2
Interface PCB
4
Reader Module
5
Laser Pointer (if so
equipped)
6
Digital PCB
14
CPLD/Code Mismatch
CORRECTIVE
ACTION
Contact Helpdesk
for assistance
Gryphon™ I GBT4100
Base Station Indications
Base Station Indications
INDICATION
LEDS
Power-up Complete
Yellow LED on
Reader Disabled by the HOST or
the communication with HOST is
not established
Yellow LED blinking
~1Hz
Data/labels are transmitted to
the HOST
Yellow LEDs turned off
for 100mSec
Programming Mode
Yellow LED blinks
quickly
Configuration alignment with
the HH is in progress
Red LED blinks quickly
Battery charger in progress
Red LED on
Battery charger complete
Green LED on
Battery charger error
Green LED and Red LEDs
blink alternatively ~1Hz
No HH is placed on the cradle
Red and Green LEDs off
Quick Reference Guide
41
Cleaning Procedure
Cleaning Procedure
Exterior surfaces and scan windows exposed to spills,
smudges or debris accumulation require periodic cleaning
to ensure best performance during scanning operations.
Contacts on the scanner and base should also be cleaned
as needed to ensure a good connection.
Follow the procedures described in this instruction sheet
to keep your Gryphon device in good operating condition.
Be sure to turn off power and unplug the device
from electrical outlet before cleaning.
CAUTION
Common Cleaning Solutions
The cleaners and disinfectants listed below are recommended for use on Datalogic’s Disinfectant-Ready Enclosures:
Cleaners
Disinfectants
Formula 409® Glass and surface cleaner
CaviWipes™
Isopropyl alcohol
Clorox® bleach
Dish soap and water
Hepacide Quat® II
Windex® Original (Blue)
Sani-Cloth®
Virex® II 256
Disinfectants may be harsh on metal contacts. They are recommended for use only on
enclosures.
42
Gryphon™ I GBT4100
Cleaning Procedure
CAUTION
DO NOT spray or pour cleaner directly onto the
unit.
DO NOT use solutions in their concentrated
form.
DO NOT use aerosols, solvents or abrasives.
DO NOT use paper towels or rough cloths to
clean windows.
Cleaning enclosure and window surfaces
1.
Moisten a soft cloth with a recommended cleaning solution. Be sure to apply the solution to
your cloth first. Wring excessive liquid from the
cloth.
2.
Use the cloth to wipe down the surface of the
unit. Use cotton swabs, lightly moistened, to
reach in corners and crevices.
3.
Minimize the amount of disinfectant applied to
the contacts.
4.
Use another clean dry cloth to remove any residue of the cleaning agent and ensure the unit is
dry.
Cleaning electrical contact surfaces
1.
Clean the enclosure and window first, as
described above.
2.
Use a soft cloth moistened with any isopropyl
alcohol to clean the surface of the contact. Use
care not to leave any cloth residue.
3.
If needed, use a nylon bristled brush to remove
stubborn contamination. Additionally, a clean
pencil eraser can be rubbed on the handheld
contacts.
Quick Reference Guide
43
Cleaning Procedure
4.
44
Finish by wiping with another clean dry cloth to
remove any remaining cleaning agent and
ensure the unit is dry.
Gryphon™ I GBT4100
Datalogic Limited Factory Warranty
Datalogic Limited Factory Warranty
Warranty Coverage
Datalogic warrants to Customer that Datalogic's products will be
free from defects in materials and workmanship for a period of
one year from product shipment.
Datalogic hardware products are warranted against defects in
material and workmanship under normal and proper use. The liability of Datalogic under this warranty is limited to furnishing
the labor and parts necessary to remedy any defect covered by
this warranty and restore the product to its normal operating
condition. Repair or replacement of product during the warranty
does not extend the original warranty term. Products are sold on
the basis of specifications applicable at the time of manufacture
and Datalogic has no obligation to modify or update products
once sold.
If Datalogic determines that a product has defects in material or
workmanship, Datalogic shall, at its sole option repair or replace
the product without additional charge for parts and labor, or credit or refund the defective products duly returned to Datalogic. To
perform repairs, Datalogic may use new or reconditioned parts,
components, subassemblies or products that have been tested
as meeting applicable specifications for equivalent new material
and products. Customer will allow Datalogic to scrap all parts removed from the repaired product. The warranty period shall extend from the date of shipment from Datalogic for the duration
published by Datalogic for the product at the time of purchase
(Warranty period). Datalogic warrants repaired hardware devices
against defects in workmanship and materials on the repaired
assembly for a 90 day period starting from the date of shipment
of the repaired product from Datalogic or until the expiration of
the original warranty period, whichever is longer. Datalogic does
not guarantee, and it is not responsible for, the maintenance of,
damage to, or loss of configurations, data, and applications on the
repaired units and at its sole discretion can return the units in the
“factory default” configuration or with any software or firmware
update available at the time of the repair (other than the firmware or software installed during the manufacture of the product). Customer accepts responsibility to maintain a back up copy
of its software and data.
Warranty Claims Process
In order to obtain service under the Factory Warranty, Customer
must notify Datalogic of the claimed defect before the expiration
of the applicable Warranty period and obtain from Datalogic a return authorization number (RMA) for return of the product to a
designated Datalogic service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or replace product
without additional charge for parts and labor. Customer shall be
responsible for packaging and shipping the product to the designated Datalogic service center, with shipping charges prepaid.
Datalogic shall pay for the return of the product to Customer if
the shipment is to a location within the country in which the Datalogic service center is located. Customer shall be responsible
Quick Reference Guide
45
Datalogic Limited Factory Warranty
for paying all shipping charges, duties, taxes, and any other
charges for products returned to any other locations. Failure to
follow the applicable RMA policy, may result in a processing fee.
Customer shall be responsible for return shipment expenses for
products which Datalogic, at its sole discretion, determines are
not defective or eligible for warranty repair.
Warranty Exclusions
The Datalogic Factory Warranty shall not apply to:
(i) any product which has been damaged, modified, altered,
repaired or upgraded by other than Datalogic service personnel or its authorized representatives;
(ii) any claimed defect, failure or damage which Datalogic
determines was caused by faulty operations, improper
use, abuse, misuse, wear and tear, negligence, improper
storage or use of parts or accessories not approved or
supplied by Datalogic;
(iii) any claimed defect or damage caused by the use of product with any other instrument, equipment or apparatus;
(iv) any claimed defect or damage caused by the failure to
provide proper maintenance, including but not limited to
cleaning the upper window in accordance with product
manual;
(v) any defect or damage caused by natural or man-made
disaster such as but not limited to fire, water damage,
floods, other natural disasters, vandalism or abusive
events that would cause internal and external component damage or destruction of the whole unit, consumable items;
(vi) any damage or malfunctioning caused by non-restoring
action as for example firmware or software upgrades,
software or hardware reconfigurations etc.;
(vii) the replacement of upper window/cartridge due to
scratching, stains or other degradation and/or
(viii) any consumable or equivalent (e.g., cables, power supply,
batteries, keypads, touch screen, triggers etc.).
No Assignment
Customer may not assign or otherwise transfer its rights or obligations under this warranty except to a purchaser or transferee
of product. No attempted assignment or transfer in violation of
this provision shall be valid or binding upon Datalogic.
DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NONINFRINGEMENT. DATALOGIC
SHALL NOT BE LIABLE FOR ANY DAMAGES SUSTAINED BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE ABOVE. THE REMEDY SET
FORTH IN THIS WARRANTY STATEMENT IS THE CUSTOMER’S
SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS. UNDER
NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO CUSTOMER
OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT
46
Gryphon™ I GBT4100
Datalogic Limited Factory Warranty
DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit
to Datalogic. Datalogic shall assume risk of loss or damage for
product in Datalogic’s possession. In the absence of specific written instructions for the return of product to Customer, Datalogic
will select the carrier, but Datalogic shall not thereby assume any
liability in connection with the return shipment.
Quick Reference Guide
47
Ergonomic Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk
of ergonomic injury follow the recommendations below. Consult with your local Health &
CAUTION Safety Manager to ensure that you are adhering
to your company’s safety programs to prevent
employee injury.
48
•
Reduce or eliminate repetitive motion
•
Maintain a natural position
•
Reduce or eliminate excessive force
•
Keep objects that are used frequently within
easy reach
•
Perform tasks at correct heights
•
Reduce or eliminate vibration
•
Reduce or eliminate direct pressure
•
Provide adjustable workstations
•
Provide adequate clearance
•
Provide a suitable working environment
•
Improve work procedures.
Gryphon™ I GBT4100
Support Through the Website
Support Through the Website
Datalogic provides several services as well as technical
support through its website.
Log on to www.datalogic.com and click on the SUPPORT >
GENERAL DUTY HANDHELD SCANNERS category link.
From this page you can select your product model from
the dropdown list which gives you access to:
Downloads including Data Sheets, Manuals, Software &
Utilities, and Drawings;
Repair Program for On-Line Return Material Authorizations (RMAs) plus Repair Center contact information;
Service Program containing details about Maintenance
Agreements;
Quick Reference Guide
49
Keypad
Keypad
Use the barcodes that follow to enter numbers as you
would select digits/characters from a keypad.
If you make a mistake, scan the CANCEL barcode below to
abort and not save the entry string. You can then start
again.
Cancel an incomplete HID Variable PIN Code
Finish by scanning the Exit HID Variable PIN Code label.
Exit HID Variable PIN Code
0
1
2
3
50
Gryphon™ I GBT4100
Keypad
4
5
6
7
8
9
Quick Reference Guide
51
www.datalogic.com
©2009-2017 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S. and the E.U.
Datalogic USA Inc.
959 Terry Street | Eugene, OR 97402 | U.S.A. |
Telephone: (541) 683-5700 |
Fax: (541) 345-7140
820091514
(Rev G)
June 2017
Download PDF
Similar pages