SATA (Serial ATA) Hard Drives for HP Workstations

QuickSpecs
SATA (Serial ATA) Hard Drives for HP
Workstations
Overview
Introduction
SATA 7200 rpm drives are our standard high bandwidth hard drive storage options; most workstation models are also
available with high performance 10K rpm rotation speeds. Storage capacities for the 7200 rpm drives range up to a
massive 3.0TB.
Most of the 7200 rpm HDDs are 3.5" drives. The one exception is the new 500GB SATA 7200 rpm SED drive which is 2.5"
form factor. The 10K rpm drives are SFF (Small Form Factor, 2.5") drives (available bare and in 3.5" frames); the
appropriate choice depends on drive bay availability in a chassis.
SATA 10K Performance
The SATA 10K family of drives are high performance drives. They offer sustained data transfers to and from the drive up
200MB/s, as compared with SATA 7200 rpm drives which offer sustained data transfers up to 130MB/s. In addition, the
Reliability performance is rated at MTBF of 2,000K hours, vs 600-750K hours for SATA 7200 rpm drives.
SMART technology
Self Monitoring Analysis and Reporting Technology (SMART) hard drive technology allows hard drives to monitor their own
health and to raise flags if imminent failures are predicted. If the drive determines that a failure is imminent, the SMART
hard drive technology enables intelligent manageability or management software to generate a fault alert. While the legacy
versions of SMART hard drives do a good job monitoring the data on the hard drive media, the ever increasing emphasis
on reliability and quality has prompted HP to implement SMART IV technology which constantly checks that the data flow
from host interface to media and media to host interface is not compromised. This is accomplished by inserting a parity
code into every 512 byte block in the data path of the hard drive's Cache RAM. This parity checking performed by HP's
SMART IV technology hard drives, allows for more complete error detection coverage encompassing the entire data path
between the host and the hard drive.
Smart IV is also known as IOEDC: I/O Error Detection Code.
Restrictions on Hazardous Substances (RoHS)
RoHS is a European Union directive that requires OEM manufacturers' compliance. The directive assures that hazardous
substances are not contained within electronic equipment. Those substances include lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls and polybrominated diphenyl ethers. Hewlett-Packard is committed to adhering to this
directive.
Native Command Queuing
NCQ, or Native Command Queuing, is a capability of modern SATA drives. NCQ is a SATA protocol extension that allows
the hard drive to have several write or read commands outstanding at the same time. In contrast, normal non-queued
operation requires each command to be completed before the next command is issued by the host system. Queuing allows
the drive to complete the commands in the order that allows for best overall throughput. It also involves an advanced
method of transferring data to or from the host, called First Party Direct Memory Access (FPDMA), that allows the hard
drive and the host controller to manage the data transfers for multiple outstanding commands, without involving the host
processor. NCQ can contribute to better performance but the results are dependent on many factors, including the access
patterns of the various applications and operating system functions that are initiating drive accesses. It requires support
from the host system BIOS, controller, and driver in order to be useful. However NCQ-capable drives are compatible with
host systems that do not include the support; the NCQ and FPDMA features are simply not used on those systems.
Self Encrypting Drive (SED) support
The Trusted Computing feature set which has been developed by the Trusted Computing Group (TCG) is supported.
Specifically, the Opal Security Subsystem class (SSC) is supported. This feature allows the HDD to do the following:
Deploy Storage Device and Take Ownership: the HDD is integrated into its target system and ownership transferred
by setting or changing the Storage Device's owner credential.
Activate or Enroll Storage Device: LBA ranges are configured and data encryption and access control credentials
(re)generated and/or set on the Storage Device. Access control is configured for LBA range unlocking.
Lock and Unlock Storage Device: unlocking of one or more LBA ranges by the host and locking of those ranges
under host control via either an explicit lock or implicit lock triggered by a reset event. MBR shadowing provides a
mechanism to boot into a secure pre-boot authentication environment to handle device unlocking.
DA - 12320 Worldwide QuickSpecs — Version 22 — 7.1.2014
Page 1
QuickSpecs
SATA (Serial ATA) Hard Drives for HP Workstations
Overview
Repurpose and End-of-Life: erasure of data within one or more LBA ranges and reset of locking credential(s) for
Storage Device repurposing or decommissioning.
GB = 1 billion bytes. Actual available capacity is less.
Most of our platforms support SED HDD and SED SSD. Additional platforms will support this technology in the coming
months. Check specific platforms for availability.
Performance
SATA Hard Drives use the SATA III interface running at up to 6 Gb/s. Actual sustained transfer rates are lower due to
command protocol and SATA bus management overhead.
Models
250GB SATA 10K rpm SFF HDD
500GB SATA 10K rpm SFF HDD
1TB SATA 10K rpm SFF HDD
500GB SATA 7200 rpm 6Gb/s 3.5" HDD
1TB SATA 7200 rpm 6Gb/s 3.5" HDD
2.0TB SATA 7200 rpm 6Gb/s 3.5" HDD
3.0TB SATA 7200 rpm 6Gb/s 3.5" HDD
500GB SATA 7.2K SED SFF HDD
B8X18AA
B8X19AA
B8X20AA
LQ036AA
LQ037AA
QB576AA
QF298AA
D8N29AA
Compatibility
Most SATA Hard Drives are compatible with all of the current HP Z-series Workstations (check the individual workstation
QuickSpecs for current hard drive compatibility information).
The 3.0TB SATA HDD is compatible with the new platforms, and also as attached to the LSI9260 Controller Card. The
3.0TB capacity will not be realized if the drive is attached to the onboard SATA controller for Z400, Z600, and Z800.
When ordering drives as After Market Options for use in an optical bay, order an appropriate bracket as follows:
HP Z-series Workstations
3.5" drive bracket for HP Z400, Z600 and Z800, HP Optical Bay HDD Mounting Bracket-BLK-for WKS, HP Part
Number NQ099AA
2.5" (SFF) bracket for Z600 and Z800, HP 2.5in HDD 2:1 Optical Bay Bracket, HP Part Number FX615AA
HP xw4600 or xw6600 Workstation: 3.5" drive bracket, HP Optical Bay HDD Mounting Bracket, HP Part Number
DY659AA.
Not all hard drive models are available in all regions.
Service and Support
Your Option Limited Warranty is a one (1) year (HP Option Limited Warranty Period) parts replacement warranty on any
HP-branded or Compaq-branded options (HP Options). If your HP Option is installed in an HP Hardware Product, HP may
provide warranty service either for the HP Option Limited Warranty Period or the remaining Limited Warranty Period of the
HP Hardware Product in which the HP Option is being installed, whichever period is the longer but not to exceed three (3)
years from the date you purchased the HP Option.
DA - 12320 Worldwide QuickSpecs — Version 22 — 7.1.2014
Page 2
QuickSpecs
SATA (Serial ATA) Hard Drives for HP Workstations
Technical Specifications
Hard Drives
250GB SATA 10K rpm
SFF HDD
Capacity
Height
Width
250GB
0.6 in; 1.53 cm
Media Diameter
2.5 in; 6.36 cm
Physical Size
2.75 in; 6.99 cm
Interface
Serial ATA (6Gb/s)
Synchronous Transfer Up to 600MB/s
Rate (Maximum)
Buffer
64MB
Cache
Adaptive
Seek Time (typical
Single Track
1.2ms (typical)
reads, includes controller Average
3.6ms
overhead, including
Full Stroke
9.0ms (typical)
settling)
Rotational Speed
10K rpm
Operating Temperature41° to 131° F (5° to 55° C)
500GB SATA 10K rpm
SFF HDD
Capacity
Height
Width
1TB SATA 10K rpm
SFF HDD
Capacity
Height
Width
500GB
0.6 in; 1.53 cm
Media Diameter
2.5 in; 6.36 cm
Physical Size
2.75 in; 6.99 cm
Interface
Serial ATA (6Gb/s)
Synchronous Transfer Up to 600MB/s
Rate (Maximum)
Buffer
64MB
Cache
Adaptive
Seek Time (typical
Single Track
1.2ms (typical)
reads, includes controller Average
3.6ms
overhead, including
Full Stroke
9.0ms (typical)
settling)
Rotational Speed
10K rpm
Operating Temperature41° to 131° F (5° to 55° C)
1TB
0.6 in; 1.53 cm
Media Diameter
2.5 in; 6.36 cm
Physical Size
2.75 in; 6.99 cm
Interface
Serial ATA (6Gb/s)
Synchronous Transfer Up to 600 MB/s
Rate (Maximum)
Buffer
64MB
Cache
Adaptive
Seek Time (typical
Single Track
1.2ms (typical)
reads, includes controller Average
3.6ms
overhead, including
Full Stroke
9.0ms (typical)
settling)
Rotational Speed
10K rpm
Operating Temperature41° to 131° F (5° to 55° C)
DA - 12320 Worldwide QuickSpecs — Version 22 — 7.1.2014
Page 3
QuickSpecs
SATA (Serial ATA) Hard Drives for HP Workstations
Technical Specifications
500GB SATA 7200 rpm Capacity
6Gb/s 3.5" HDD
Height
Width
500GB
0.6 in; 1.53 cm
Media Diameter
3.5 in; 8.9 cm
Physical Size
4 in; 10.17 cm
Interface
Serial ATA (6.0Gb/s), NCQ enabled
Synchronous Transfer Up to 600MB/s
Rate (Maximum)
Buffer
16MB
Cache
Segmentable
Seek Time (typical
Single Track
2 ms
reads, includes controller Average
11 ms
overhead, including
Full-Stroke
21 ms
settling)
Rotational Speed
7,200 rpm
Logical Blocks
976,773,168
Operating Temperature41° to 131° F (5° to 55° C)
1TB SATA 7200 rpm
6Gb/s 3.5" HDD
Capacity
Height
Width
1 Terabyte (1000 GB)
1 in; 2.54 cm
Media Diameter
3.5 in; 8.9 cm
Physical Size
4 in; 10.17 cm
Interface
Serial ATA (6.0Gb/s), NCQ enabled
Synchronous Transfer Up to 600 MB/s
Rate (Maximum)
Cache
64MB
Seek Time (typical
Single Track
2 ms
reads, includes controller Average
11 ms
overhead, including
Full-Stroke
21 ms
settling)
Rotational Speed
7,200 rpm
Logical Blocks
1,953,525,168
Operating Temperature41° to 131° F (5° to 55° C)
2.0TB SATA 7200 rpm
6Gb/s 3.5" HDD
Capacity
Height
Width
2TB
1 in; 2.54 cm
Media Diameter
3.5 in; 8.9 cm
Physical Size
4 in; 10.17 cm
Interface
Serial ATA (6.0 Gb/s), NCQ Enabled
Synchronous Transfer Up to 600 MB/s
Rate (Maximum)
Cache
64MB
Seek Time (typical
Single Track
2 ms
reads, includes controller Average
11 ms
overhead, including
Full-Stroke
21 ms
settling)
Rotational Speed
7,200 rpm
Logical Blocks
3,907,029,168
Operating Temperature41° to 131° F (5° to 55° C)
DA - 12320 Worldwide QuickSpecs — Version 22 — 7.1.2014
Page 4
QuickSpecs
SATA (Serial ATA) Hard Drives for HP Workstations
Technical Specifications
3.0TB SATA 7200 rpm
6Gb/s 3.5" HDD
Capacity
Height
Width
3.0TB
1 in; 2.54 cm
Media Diameter
3.5 in; 8.9 cm
Physical Size
4 in; 10.17 cm
Interface
Serial ATA (6.0Gb/s), NCQ enabled
Synchronous Transfer Up to 6.0 Gb/s
Rate (Maximum)
Buffer
64MB
Seek Time (typical
Single Track
0.6 ms
reads, includes controller Average
11 ms
overhead, including
Full-Stroke
Not specified
settling)
Rotational Speed
7200 rpm
Operating Temperature41° to 140° F (5° to 60° C)
500GB SATA 7.2K SED Capacity
SFF HDD
Height
500GB
0.275 in; 0.7 cm
Width
Media Diameter
2.5 in; 6.36 cm
Physical Size
2.75 in; 6.99 cm
Interface
Serial ATA (6Gb/s)
Synchronous Transfer Up to 600MB/s
Rate (Maximum)
Buffer
32MB
Seek Time (typical
Single Track
1 ms
reads, includes controller Average
4.2 ms
overhead, including
Full-Stroke
25 ms (typical)
settling)
Rotational Speed
7,200 rpm
Operating Temperature32° to 140° F (0° to 60° C)
© Copyright 2014 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
DA - 12320 Worldwide QuickSpecs — Version 22 — 7.1.2014
Page 5
Download PDF
Similar pages