JDSU LTE Network End-to-End Test Solutions
Communications Test and Measurement Solutions
Table of Contents
Introduction .................................................................................................................................... 3
E6474A Drive Test — LTE Network Wireless Optimization ........................................... 4
W1314A measurements ................................................................................................................. 4
Chipset measurements ................................................................................................................. 5
E6474 tests ........................................................................................................................................ 6
Leading platform functions ......................................................................................................... 7
SART/DNA LTE Distributed Network Analyzer ..................................................................
Hardware functions ........................................................................................................................
Protocol decoding ..........................................................................................................................
Call tracking ......................................................................................................................................
KPI statistical analysis .....................................................................................................................
Application scenarios .....................................................................................................................
7
8
8
8
8
9
JD745A Base Station Analyzer ................................................................................................ 10
Spectrum analyzer ..........................................................................................................................10
LTE transmitter analysis .................................................................................................................11
Monitored LTE interfaces and protocols .................................................................................. 13
acceSSLTE Network and Service Assurance System ........................................................13
Real-time (KPI Alarm) Monitoring .............................................................................................. 14
Real-time/historical fault troubleshooting ..............................................................................14
Application scenarios .....................................................................................................................15
PacketInsight .................................................................................................................................. 16
T-BERD 6000A & 8000 Multi-Service Application Module (MSAM) .......................... 17
T-BERD 5800 Handheld Network Test Family of Products ............................................18
SmartClass Ethernet .................................................................................................................... 19
Fiber Inspection, Cleaning and Test Solutions ..................................................................19
Power Measurement and Fiber Identification Solutions .............................................. 20
OTDR and Optical Power Measurement Solutions ..........................................................20
2
Introduction
LTE is transforming wireless and core networks and network transmission.
OFDM and MIMO are being introduced as over-the-air interfaces, while PTN’s
development for mobile backhaul and all-IP network architecture and high-speed
data transmission presents huge challenges and opportunities to broader applications of the LTE network. JDSU offers the industry’s most advanced and most
comprehensive test and measurement technology solutions for various stages
of LTE research and development, testing, deployment, and optimization by
operators and network equipment manufacturers.
PacketInsight
T-BERD
HST-3000
Drive Test
Network topology and JDSU LTE test tools
3
E6474A Drive Test — LTE Network Wireless Optimization
The JDSU drive test solution lets operators and network equipment manufacturers efficiently deploy and optimize today’s increasingly complex wireless
voice and data networks by conducting optimization and troubleshooting on
FDD-LTE FDD-LTE and TD-LTE networks. The E6474A drive test platform
supports scanner (JDSU multi-band, multi-technology receiver W1314A) and
user equipment (UE) measurements, and is the leading tool kit for optimization
and network troubleshooting.
Features
• Supports simultaneous testing of user equipment (UE) and the measurement
receiver (scanner)
• A single laptop can support up to eight devices
• Supports industry-leading data test such as Iperf, FTP, VideoStreaming, and VOIP
• Works indoors using a handset or backpack
• Correlates real-time test parameters and the base station
• Users can define event triggers
• Fast, accurate receiver (scanner) measurements
• Data records can be imported to the JDSU signaling analyzer for end-to-end
protocol tracking
• Fully supports traditional technologies such as GSM, TD-SCDMA/UMTS/HSPA+,
and cdma2000/EVDO
W1314A measurements
•
•
•
•
•
•
•
•
•
JDSU receivers support all FDD-LTE and TDD-LTE frequency bands
Supported frequencies: 700/850/900/1700/1800/1900 MHz; 2.1/2.3/2.5/2.6/3.5 GHz
LTE measurement bandwidths: 1.4/3/5/10/15/20 MHz
Frequency measurement
Channel power measurement
Continuous-wave measurement
Primary and secondary synchronization signal RSSI (P-SS) and RSSI (S-SS)
Physical layer cell ID (PID) [0, 503]
Reference signal received power (RSRP) for antenna ports 0 and 1, reference
signal received quality (RSRQ) and CINR/SINR (RS-CINR)
It can also be used on network frequency sweeping to identify problems that need
to be corrected in the network planning transmission model.
4
Chipset measurements
JDSU currently supports the following UE chipsets: Qualcomm, Samsung, LG,
and Altair. Qualcomm and Altair chipsets can conduct TD-LTE measurements,
and measure the following parameters.
Cell and random access information:
•
•
•
•
•
•
•
•
•
LTE 3GPP cell information
LTE physical cell information
LTE cell signal quality information
LTE CQI information
LTE PBCH BLER
LTE path information
LTE RACH request
LTE RACH response
LTE QCI information
Information on physically shared channels:
•
•
•
•
LTE PDSCH BLER
LTE PDSCH physical layer throughput
LTE PUSCH physical layer throughput
LTE PDCCH DCI Detection Ver
Mobile information:
•
•
•
•
•
•
•
•
•
•
•
•
LTE antenna correlation
LTE launch power
RLC/MAC/PDCP information
LTE RLC DL throughput
LTE RLC UL throughput
LTE MAC BLER
LTE MAC throughput
LTE MAC DL PDU
LTE MAC UL PDU
LTE PDCP DL throughput
LTE PDCP UL throughput
LTE PDCP PDU
Scheduler information:
• LTE UL Grant and DL Ack/Nack
• LTE UL Scheduler status
• LTE UL Control information
Protocol information log:
• RLC Protocol messages
• NAS Protocol messages
5
E6474 tests
The E6474A drive test platform can also conduct UE based tests, including:
• Iperf test
• FTP test
• VideoStreaming with MOS
• VOIP test
• Ping, HTTP test, etc.
By customizing test sequences, it can pre-set the sequence, frequency, time
interval and measurement parameters of test items. Using the E6474A platform,
test results (such as throughput, latency, bandwidth, jitter, etc.) and real-time
statistics can automatically be displayed graphically.
The LTE receiver solution supports FDD-LTE and TD-LTE technologies. You can
select one or both options based on your measurement needs.
Ordering Information
Drive Test Network Optimization Platform Options
Order Number
Basic options (supporting basic application testing such as Iperf, FTP and Ping)
FDDLTE receiver measurement
TD-LTE receiver measurement
Receiver hardware
Indoor map license
MapX indoor map license
One year software and support update service (SUS)
LTE UE Measurements (default support for Qualcomm FDD LTE and TDD LTE equipment)
LTE UE measurement equipment updated to LG device
LTE UE measurement equipment updated to Samsung device
LTE UE measurement equipment updated to Altair device
LTE UE measurement equipment updated to Sequans device
LTE UE measurement equipment updated to Hi Silicon TDD device
Wireless Application Measurement Series (such as adhesion,activation, WAP, HTTP, Web,
SMTP, POP3, etc.)
MOS measurement of streaming video
VOIP UE end measurement
VOIP Application server options
Drive Test Backpack with USB hub
Drive Test Backpack
Drive Test Battery Pack for Backpack
Drive Test Battery Charger for Backpack
E6474A
E6474A-645
E6474A-646
W1314A
E6474A-030
E6474A-040
E6474A-060
E6474A-640
E6474A-641
E6474A-642
E6474A-643
E6474A-644
E6474A-634
E6474A-740
E6474A-744
B9990A-510
B9990A-515
E6473B-920
E6473B-921
E6473B-925
E6473B-926
6
SART/DNA LTE Distributed Network Analyzer
The industry’s leading end to end LTE network test platform, able to analyze and
associate interface protocol signaling messages for a variety of network technologies, and provide the test industry’s most complete real-time monitoring,
network diagnostics and troubleshooting. SART for LTE is a comprehensive
extension of the platform, covering almost all of the mobile networks including
GSM, WCDMA, HSPA, TD-SCDMA, CDMA2000, EVDO, and IMS.
Signaling Analyzer Real-Time/
Distributed Network Analyzer
Features
• Uses high-performance GE and 10 GE interface card to capture wire-speed of
network data
• Supports the latest and most complete protocols
• Same platform to complete end to end call tracking and fault location for 2G,
3G, and LTE networks
GB/10GB Ethernet Analysis Server
• LTE network optimization and user plane data analysis
Leading platform functions
• The same platform supports 2G, 3G, and LTE/SAE/IMS protocol analysis, and
supports the following interfaces:
–– LTE & EPC includes uu, S1, X2, S5/S8 (GTPV2 & PMIP), S6a, S10, S11, S13,
SGi, Rx, Gx, and Gxc
–– 3GPP interworking includes S3, S4, S6d, S12, and S16
–– Non-3GPP interworking includes S2a(PMIP), S2b, S2c, S101, S102, and S103
–– Others include vGxa, SWa, SWd, SWm, SWx, STa, S6b, Ro, Rf (Gz), and Gy
–– LTE Voice:
oo VoGAL; Z1, Z3
oo SRVCC: Sv
oo CSFB: SGs
oo IMS: Mw/ISC/Dx/Cx/Sh
• Multi-user server usage patterns, one set of hardware can be shared by many
for parallel testing
7
• Supports multi-interface, multi-protocol automatic configurations
Hardware functions
High-performance hardware ensures test accuracy with:
• Options for high-density (8 ports or 16 ports) or portable (dual port) Gigabit
capture ports
• Supports 10GE Gigabit Ethernet interface (optical and electrical interfaces)
• Supports association test of over the air monitoring instruments (such as
Sanjole and WaveJudge)
• Supports hardware-based IP signaling messages filtering and data packet
intelligent processing
Protocol decoding
Fully supports all versions of 3GPP R8 and interface protocols:
• Supports protocols in various versions such as 3GPP R8 2008/2008-03/200806/2008-09/2008-12/2009-03/2009-06/2009-09/2009-12 and R9 2010-03/201006/2010-09/2010-12.
• Supports LTE NAS signaling decryption test and can automatically get the key
from the adjacent interfaces for real-time decryption of the signaling
• Supports LTE and TD-SCDMA/GSM as well as UMTS network interoperability testing
• Supports interoperability testing between LTE networks
• Includes support for IPV6 and IPSec
• Supports real-time decoding and post-analysis as well as Wireshark/PCAP
format import and export
Call tracking
Automatic multi-interface correlation analysis, able to generate complete crossinterface flow for any call:
•
•
•
•
Supports end-to-end correlation for multi-interface call flows
Includes support for Uu/S1/X2/S5/S6a/S8/S11/S10/Gx/Rx
Supports joint call tracking between user planes and signaling planes
S1 or X2 based switching process analysis
KPI statistical analysis
Includes statistical analysis for multi-interface and multi-network elements and
traffic analysis at the E-RAB-level:
• Can perform comprehensive statistical analysis on signaling and user planes,
accurately calculate throughput and latency as well as analyze TCP session retransmissions
• Draws curve charts for a variety of indicators and mark events
8
• Performs in-depth analyses of user call drop rate, QCI, and other indicators
Application scenarios
• LTE network interface signaling monitoring and fault location
• Interworking among LTE networks and interoperability testing between LTE
and 2G, 3G, and LTE voice networks (such as SRVCC, CSFB)
• Analysis of LTE network user plane performance such as QoS and throughput
analysis
• LTE wireless network optimization, such as analyzing user adhesion rate by
cellpower and call drop rate
SART/DNA LTE Distributed Network Analyzer
Order Number
High density distributed network analyzer
8-port 10/100/1000M
16 port 10/100/1000M Ethernet interface card
10 GE and 10/100/1000M integrated Ethernet capture card
Basic software for signaling analysis platform
Multi-user server platform software
Software options supporting LTE Network interface
LTE IP Sec Decipher
LTE NAS Decipher
LTE uu interface supporting options
LTE uu interface Sanjole supporting options
LTE uu interface E6474A NiXT drive test supporting options
IMS supporting options
Network analyzer 10GE hardware supporting options
Ethernet network analyzer
J6804A
J6850A
J6851A
J6872A-10G
J7830A
J7831A
J7880A
J7881A
J7882A
J7889A
J7889A-SJ1
J7889A-NX1
J7844A
J6865A
J6840A
Ordering Information
9
JD745A Base Station Analyzer
The JD745A base station analyzer is mainly used for development, debugging,
testing, installation and maintenance of a variety of base stations for modern communication systems. It utilizes spectrum analysis, signal quality and modulation
analysis, antenna system testing, power meter, and T1/E1 analysis capabilities,
and supports all mainstream modern communication systems and formats. Test
frequencies cover 100 k - 4 GHz. It also includes support for GSM/GPRS, EDGE,
TD-SCDMA, PCS/DCS, WCDMA/HSDPA, CDMA2000, EV-DO, and TD-LTE
and FDD LTE.
Interference analysis
Transmitter modulation
analysis
Spectrum analysis
Antenna testing
JD745A Base Station Analyzer
E1/T1 transmission
line test
Power Measurement
Spectrum analyzer
Functions include:
•
•
•
•
•
•
•
Channel power
Spectral mask test
Occupied bandwidth measurement
Adjacent channel power
Spurious emission
Field strength
AM/FM audio demodulation
10
LTE transmitter analysis
JD745A modulation domain measurement suite not only provides systematic
RF parameters, but also measures and analyzes in detail modulation domain
parameters of modern mainstream communications systems. Built-in standard
test procedure allows the user to achieve one-touch automatic measurement.
Functions include:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Channel power
Adjacent channel leakage power ratio (ACLR)
Emission mask
Occupied bandwidth
Spurious emission
Power vs. time
Data channel summary
Control channel summary
Subframe summary
Frame summary
Frequency error
Complementary cumulative distribution function (CCDF)
EVM (Peak/RMS)
Origin offset
Time offset
Total EVM
P-SCH/S-SCH/PBCH/PCFICH/PHICH/PDCCH/PDSCH/RS EVM power
Constellation
EVM vs. subcarrier
EVM vs. symbol
Spectral flatness
ID Scanner
MultiPath profile (Ec/Io, Delay)
Cell, Group ID, Sector ID
RX power trend
11
In addition, JD745A also supports the following functions:
•
•
•
•
•
•
•
Over the air measurement
Cable and antenna analysis
Power meter
E1/T1 analyzer
Interference analysis
Automatic testing
GPS and geographic information
Ordering Information
JD745A Base Station Analyzer
Order Number
GPS receiver and antenna
Interference Analyzer
Channel scan
CDMA2000 signal analysis
EVDO signal analysis
GSM/GPRS/EDGE signal analysis
WCDMA signal analysis
HSDPA signal analysis
TD-SCDMA signal analyzer
Mobile WiMAX signal analysis
FDD-LTE signal analysis
TDD-LTE signal analysis
CDMA2000 over the air signal analysis
EVDO over the air signal analysis
GSM/GPRS/EDGE over the air signal analysis
WCDMA/HSDPA over the air signal analysis
TD-SCDMA over the air signal analysis
Mobile WiMAX over the air signal analysis
FDD-LTE over the air signal analysis
TDD-LTE over the air signal analysis
Through-type power type
End connecting type power probe
JD745A010
JD745A011
JD745A012
JD745A020
JD745A021
JD745A022
JD745A023
JD745A024
JD745A025
JD745A026
JD745A028
JD745A029
JD745A040
JD745A041
JD745A042
JD745A043
JD745A045
JD745A046
JD745A048
JD745A049
JD731A
JD732A
12
acceSSLTE Network and Service Assurance System
This is the industry’s leading LTE network-wide monitoring and trouble-shooting platform, with 24x7 support for the capture and correlated analysis of all LTE
network interface signaling and user plane information.
Supporting 2G, 3G, and LTE monitoring in a single solution, accessLTE is an
essential tool for LTE network operations, typically reducing fault resolution
times by up to 80%.
Features
• Automatic correlation of probe data across multiple interfaces and across
signaling and user planes
• Integrated monitoring and troubleshooting applications such that three mouse
clicks can take the user from high-level KPI alarms to a display of impacted
users’ detailed signaling procedures, thereby greatly improving the speed of
fault resolution
• Intelligent KPI definition and alarm thresholding, including procedure-based
“composite” KPIs that enable fast detection of service faults
• A single platform for complete, end-to-end session tracing and fault location
for 2G, 3G, and LTE networks including I-RAT handovers
Monitored LTE interfaces and protocols
The accessLTE solution delivers actionable information from data captured on
interfaces at key LTE network elements—MME, SGW, PGW, PRCF—as well as
interfaces to interconnected 2/3 G networks.
• Supports 1/10 GE physical interfaces
• Fully supports all versions of 3GPP Rel 8 interfaces and protocols including:
–– S1-MME, S10, S11, S6a: carries control-plane data between the E-UTRAN
and core-network NEs (for example, MME and SGW). Provides details on
session set-up, refresh, and tear-down.
–– S1u, S5, SGi: carries user-plane information between the E-UTRAN and
core-network NEs (for example, SGW and PGW). Provides details about
end-user services such as web access and email.
–– Gx, Rx: carries (PRCF) control-plane data relating to charging and policy
control
–– Gn, S4: carries control-plane data between LTE and interconnected 2/3 G
networks
13
Real-time (KPI Alarm) monitoring
The accessLTE QoS Analyzer provides a comprehensive range of real-time KPIs
delivering immediate visibility into customer, service, and network QoS.
Defined KPIs cover both signaling and user-plane performance and include:
• Key LTE network procedures such as device attach and handovers
• End-user throughput and latency
• Retransmission of TCP sessions
Real-time/historical fault troubleshooting
The accessLTE Session Trace application provides automatic correlation across
multiple interfaces and is able to generate a single complete cross-interface
transaction trace for any LTE session.
14
Functionality also includes:
•Simple investigation workflows driven by common information such as Cell,
IMEI, IMSI, MSISDN and failure cause
•Automatic highlighting of problems
•Detailed analysis of intra-LTE and I-RAT handovers
Application scenarios
•Detection and diagnosis of LTE network and service faults with detailed analysis across both the signaling and user planes
•Analysis of LTE network user experience, including user plane throughput analysis
•LTE network optimization, such as analyzing user service activation success
rate by cell, QCI setting, and other configuration dimensions
Ordering Information
LTE software options
Order Number
Session Trace 50Mbps MME traffic
Session Trace 5Gbps SGW traffic
Session Trace 10Mbps MME traffic
Session Trace 1Gbps SGW traffic
LTE Protocol Pack 2 Session Trace
Session Trace Mobile Charging Protocol Pack
QoS Analyzer 50Mbps MME traffic
QoS Analyzer 5Gbps SGW traffic
QoS Analyzer 10Mbps MME traffic
QoS Analyzer 1Gbps SGW traffic
LTE Protocol Pack 2 QoSA
QoSA Mobile Charging Protocol Pack
QoSA LTE Composite Measurement Pack
E4261A-L00
E4261A-L01
E4261A-L02
E4261A-L03
E4261A-L04
E4261A-L05
E4261A-L10
E4261A-L11
E4261A-L12
E4261A-L13
E4261A-L14
E4261A-L15
E4261A-L17
15
PacketInsight
PacketInsight
With the introduction of 10 G into today’s wireline and wireless networks, the
sheer volume of data traffic causes significant challenges for network operators
and equipment manufacturers to effectively troubleshoot their problems or
routinely monitor network performance. Given the sheer number of devices on
the network and multi-G traffic rates, real-time troubleshooting is a daunting
task. PacketInsight from JDSU solves this issue in the most rapid and effective
fashion possible, utilizing an advanced hardware/software indexing solution
that is easy to deploy and use.
Features
• LINUX-based high-speed 1/10 GE packet-capture appliance designed to continuously capture, index, and store to disk at 10 G rates
• Web-based GUI provides an easy-to-use interface accessible from a standard
browser
• Open XML API provides for remote control capabilities, query manipulation,
and data retrieval
• Can be used as a standalone device or in conjunction with SART for flexible
network monitoring
• The only deep packet inspection (DPI) product that can capture data at 10 G
and simultaneously create an index of user sessions to accelerate end-user productivity
• Available in 3 different storage configurations: 40 TB, 88 TB, and 130 TB with
support for 1 G and 10 G ports. The 130 TB version allows for 25 hours of data
capture at 10 G rates.
Ordering Information
Please contact your JDSU representative for ordering information.
16
T-BERD 6000A & 8000 Multi-Service Application Module (MSAM)
These tools extend the leading portfolio of T-BERD/MTS portable test solutions
created by experts to simplify network deployment and trusted by leading service
providers around the world.
Benefits
T-BERD® 6000A Compact Network Test Platform
• Maximizes ROI with a modular, field-upgradeable tester that seamlessly
expands into future technologies and interfaces
• Provides an industry-leading, multi-port 10 G modular platform for network
field installation, advanced troubleshooting
• Guarantees end-customer satisfaction with deep application layer testing for
data (TrueSpeed™ per RFC 6349), voice (VoIP), and video (IPTV)
• Promotes an efficient service and network-management life cycle with
integrated installation tools and advanced troubleshooting analysis in a single
test instrument
• Reduces installation and troubleshooting times with automated J-Complete test
tools that follow best practices and provide repeatable methods and procedures
with easy-to-understand results
Applications
• Tests and troubleshoots converged Ethernet/IP backhaul at 10 Mbps to 10 G
interfaces and captures and analyzes packets
• Tests Layers 1-3 Ethernet/IP SLAs with an auto¬mated, enhanced RFC 2544/
SAMComplete per ITU-T Y.1564
• Tests TDM/PDH to SONET/SDH at OC-3/STM-1 to OC-192/STM-64,
including service-disrup¬tion measurements and path-overhead (POH)
capture with triggers
• Enables installation and maintenance of OTN networks up to 11.1 G interface
with ODU-0 support for Ethernet client interfaces
• Validates network synchronization for quality of experience on mobile applications
–– Emulates a 1588v2 master clock/slave recovery to ensure proper point-topoint (PTP) message propagation and to verify packet delay varia¬tion
(PDV)
–– Verifies accurate SyncE frequency synchroniza¬tion and Ethernet synchronization message channel (ESMC) message propagation
• Ready for packet transport networks using MPLS-TP
• Supports J-Complete, an exclusive suite of auto¬mated test tools from JDSU
• Supports SFP and XFP pluggable optics, includ¬ing 50 GHz C-band tunable
XFPs
Ordering Information
Please contact your JDSU representative for ordering information.
17
T-BERD 5800 Handheld Network Test Family of Products
This is the latest addition to the leading portfolio of T-BERD/MTS portable test
solutions—created by experts to simplify network deployment and trusted by
leading service providers worldwide.
Benefits
T-BERD® 5800 Handheld Network Tester
• All-in-one handheld tool designed to reduce the complexity of multi-technology
testing
• Optimized for field ease-of-use while addressing emerging network technologies
• Guarantees maximum efficiency and success in the evolution of carrier
Ethernet and mobile backhaul networks
• Ensures service life-cycle management, integrating both installation and
trouble¬shooting capabilities in one instrument
• Automates services verification with support of J-Complete suite of test tools
Applications
• Six T-BERD/MTS-5800 configurations:
–– Single- and dual-port Ethernet versions
–– With or without TDM/PDH interfaces
–– Fully loaded TDM/PDH to 10 G Ethernet, SONET, and SDH
• Layer 1-3 Ethernet/IP SLAs verification (with Class of Service) that includes
automated, enhanced RFC 2544 testing
• Support for emerging Ethernet synchronization testing including 1588v2 and
SyncE verification
• BER testing up to OC192/STM-64, service disruption, and circuit monitoring
on TDM/PDH/SONET/SDH interfaces
• Packet transport network (PTN)-ready with MPLS-TP technology
• Supports J-Complete automated suite of test applications
Ordering Information
Please contact your JDSU representative for ordering information.
18
SmartClass Ethernet
The SmartClass Ethernet product is an easy-to-use, cost-effective Ethernet testing
solution for basic physical layer cable testing, Layer 2/3 traffic generation, and full
RFC 2544 testing. The rugged, battery operated, application-specific test tool lets field
technicians turn-up Ethernet and IP services by running an RFC 2544 test or following
a set of methods and procedures. The SmartClass product comes in two major configurations, one a loopback only device and the other featuring full traffic generation.
Applications
SmartClass Ethernet
• Quickly verify basic Ethernet backhaul performance on 10/100/1 GE with
automated RFC-2544 test
• Verify Class of Services with up to 8 independent traffic streams
• Supports testing in MPLS/ VPLS networks
• Cost-effective loop device for end-to-end Layer 2/3 tests
Ordering Information
Please contact your JDSU representative for ordering information.
Fiber Inspection, Cleaning and Test Solutions
As fiber penetrates further into next-generation networks, proactively inspecting
and cleaning each connection point is no longer optional, but critical. Optimized
physical performance of fiber connections is imperative to deliver future-proof and
reliable PTN and LTE networks. Today’s fiber technician needs tools that provide
a seamless workflow for inspecting, cleaning, testing, and troubleshooting a fiber
link that also drives behavior, best practices, and field efficiency. JDSU offers essential fiber handling tools in fast, portable, and easy-to-use systems for any fiber
technician. The P5000i Digital Analysis Microscope with FiberChekPRO™ makes
it fast and easy to certify that every connection in your network is optimized and
compliant to IEC Standard pass/fail thresholds.
Ordering Information
HP3 Series Fiber Inspection and Test
System with Compact Video Display and
P500i Digital Analysis Microscope
HP3-60 Kit with P5000i Digital Analysis Microscope
and Visual Fault Locator
Product Description
Order Number
Fiber Essentials Tool Kit: Dual-mag (200/400X) FBP probe microscope and tips,
FIT-HP2-60-P4 inspection and test system with 400X PCM, FFL-050 visual fault locator,
cleaning tools, utility carrier, carrying case.
Inspection Kit: Dual –mag (200/400X)FBP probe microscope and tips, HD2 Display with
200x PCM and adaptors, case
Utility Carrier System for FBP-SE05
CDMA2000 signal analysis Digital PASS/FAIL Analysis kit: P5000i, FiberChekPRO
Software, tips and Case
Digital PASS/FAIL Analysis & Test kit: P5000i, MP-60 w/ FiberChekPRO, tips, adaptors
and Case
Visual fault locator (compact)
Visual fault locator (ruggedized) with 1.25 mm adapter
Fiber Field Cleaning Kit
FIT-S205-PRO
FBP-SE05
FBPP-UC2
FBP-SD101
FBP-SD103
FFL-050
FFL-100
FCR-CLN-01
19
Power Measurement and Fiber Identification Solutions
To deliver high-performance, best-in-class PTN or LTE networks it is critical
that the fiber systems are correctly installed and tested. This ensures that the
physical layer meets the minimum optical performance specification requirements to deliver reliable services. JDSU offers a wide array of solutions from fiber
identifiers to insertion-loss power measurement tools for standard single-mode
wavelength or CWDM and DWDM systems.
Ordering Information
Product Description
Order Number
OMK-35P Singlemode SmartPocket™ Test is a dual-wavelength optical test kit with a
single-port laser source and a power meter with a UPP interface for power level and loss
test measurement in access, metro and core networks.
OLS-35 1310/1550 nm Singlemode Light Source
OCC-55 Optical Channel Checker for CWDM wavelengths.
OCC-56 Optical Channel Checker for DWDM wavelengths
Live Fiber Identifier- integrated OPM adaptors, software and case.
2127/02
2303/11
2277/40
2277/41
FI-60
FI-60 Live Fiber Identifier (left), OLS-35 SmartPocket
Optical Light Source (center), SmartClass OCC-55
Optical CWDM Channel Checker (right)
OTDR and Optical Power Measurement Solutions
Fiber is the lifeline to your customers. The physical integrity of the fiber is
critical for optimum service delivery. It is imperative to properly characterize the
performance of the physical layer to ensure reliability. The MTS-2000 Handheld
Modular Test Set solution addresses the complexity of fiber testing and drives
maximum efficiency for technicians to perform all the tests required to ensure
optimized performance and high-quality fiber networks. The MTS-2000 handles
the widest range of test applications including OTDR, FiberComplete™ automatic
IL/ORL, CWDM analyzer, and connector inspection with IEC pass/fail analysis.
This solution makes even the most novice fiber tech an instant fiber expert.
Ordering Information
MTS-2000 Handheld Modular Test Set
Product Description
Order Number
MTS-2000 Handheld Modular Test Set
OTDR module: Last Mile range 1310/1550nm
OTDR module: Metro-Access range 1310/1550nm
FiberComplete™ Module: Metro-Access OTDR, IL, ORL 1310/1550nm
Light source option for OTDR Module (through OTDR port)
Power Meter option for OTDR Module (through OTDR port)
Optical Spectrum Analyzer for CWDM –COSA-4055
Digital PASS/FAIL Analysis & Test kit: P5000i with FiberChekPRO, 7x tips and Case
EM2000T
E4126LM
E4126MA
E4126FCOMP-MA
E41OTDRLS
E4OTDRPM
2301/01
FBP-MTS-101
Test & Measurement Regional Sales
north america
toll free : 1 866
fax : +1 301 353
228 3762
9216
latin america
tel : +1 954 688
fax : +1 954 345
5660
4668
asia pacific
tel : +852 2892
fax : +852 2892
0990
0770
emea
tel : +49
fax : +49
www.jdsu.com/test
7121 86 2222
7121 86 1222
Product specifications and descriptions in this document subject to change without notice. © 2012 JDS Uniphase Corporation 30173066 001 0512 LTE-NETWORK.BR.NSD.TM.AE May 2012
Download PDF
Similar pages