PCS150R Pro:Centric® Server Installation &

PCS150R Pro:Centric ®
Server
Installation & Setup Guide
Warranty
© Copyright 2013 LG Electronics U.S.A., Inc.
P/N: 206-4157 (Rev B)
For Customer Support/Service, please call:­­1-888-865-3026
The latest product information and documentation is available online at:
www.LGsolutions.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
L’appareil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures et de plus qu’aucun objet rempli de liquide tel que des vases ne doit être placé sur l’appareil.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user should be required to correct the interference at
his own expense.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG
Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate
this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069, USA • Phone: 1-847-941-8000
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069
2
© Copyright 2013 LG Electronics U.S.A., Inc.
206-4157
IMPORTANT SAFETY INSTRUCTIONS
1. 2. 3. 4. 5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources,
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has
two blades and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked
on or pinched, particularly at plugs,
convenience receptacles, and the point
where it exits from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination in
order to avoid injury from tip-over.
13. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
206-4157
14. Power Sources
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your INSTALLATION, consult your
product dealer or local power company.
15. Overloading
Do not overload wall power outlets and
extension cords as this can result in a risk of
fire or electric shock.
16. Disconnect Device
The AC mains plug is used as the disconnect
device. The disconnect device must remain
readily operable.
17. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Do not use liquid cleaners or aerosol cleaners.
18. Outdoor Use
Warning: To prevent fire or shock hazards, do not expose this product to rain or moisture.
19. Wet Location
Do not use this product near water or moisture or in an area, such as a basement, that
might become flooded. The apparatus shall
not be exposed to dripping or splashing and
no objects filled with liquids, such as vases,
shall be placed on the apparatus.
20. Test Equipment
In some cases, LG has supplied or recommended the use of test equipment and
devices for the setup and testing of the equipment. The operation and maintenance of test
equipment is described in their associated
instruction manuals. Please refer to these
manuals for explicit instructions regarding the
safe use and handling of the equipment.
(Continued on next page)
3
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
21. Damage Requiring Service
Unplug this product from the wall power outlet and refer servicing to qualified service
personnel under the following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions, as an
improper adjustment of other controls may
result in damage and will often require
extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
f. If the product exhibits a distinct change in
performance.
Caution: Refer all servicing to qualified
service personnel.
22. Servicing
Caution: These servicing instructions are for use by qualified service
personnel only. To reduce the risk
of electrical shock, do not perform any
servicing other than that described in the
operating instructions unless you are
qualified to do so.
23. Replacement Parts
When replacement parts are required, be
sure the service technician uses replacement
parts specified by the manufacturer or that
have the same characteristics as the original
parts. Unauthorized substitutions may result
in fire, electric shock, or other hazards.
4
24. Safety Check
Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
PCS150R Rack Installation (also see page 10)
To install the PCS150R in a rack:
• Carefully slide the PCS150R into a standard
19-inch equipment rack.
• When mounting in the rack, make sure to use
the appropriate hardware. ALL FOUR MOUNTING SCREWS MUST BE USED.
• This equipment is not designed to support
other devices. Do NOT stack other equipment
on the top of the PCS150R.
• Rear cabling must be dressed and supported
so that the weight of the cabling is not a strain
on the PCS150R connectors.
• MOUNTING OF THE EQUIPMENT IN THE
RACK SHOULD BE SUCH THAT A HAZARDOUS CONDITION IS NOT ACHIEVED DUE TO
UNEVEN MECHANICAL LOADING.
Rack-mount Considerations
A.Elevated Operating Ambient
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient. Therefore, consideration
should be given to installing the equipment in
an environment compatible with the maximum
ambient temperature (Tma) specified by the
manufacturer (see Specifications information
in this document).
(Continued on next page)
206-4157
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
B.Reduced Air Flow
Installation of the equipment in a rack should
be such that the amount of air flow required
for safe operation of the equipment is not
compromised. To ventilate the system normally and avoid overheating, leave at least
1 inch (2.5 cm) on each side (including top
and bottom) of the PCS150R. Do NOT stack
other equipment on the top of the PCS150R.
Also, ensure the unit’s AC power adapter
is never stacked or bundled with other AC
power adapters. Each adapter should have
adequate ventilation and should be isolated
from other heat sources.
C.Circuit Overloading
Consideration should be given to the connection of the equipment to the supply circuit
and the effect that overloading of the circuits
might have on overcurrent protection and
supply wiring.
D.Reliable Earthing
Maintain reliable earthing of rack-mounted
equipment. Particular attention should be
given to supply connections other than direct
connections to the branch circuit (e.g. use of
power strips).
206-4157
E. Mains Outlet Earthing
The apparatus with Class I construction must
be connected to a mains socket outlet with a
protective earthing connection.
PCS150R Installation on a Flat Surface
To install the PCS150R on a level surface (table
top, shelf, etc.):
• Install the equipment in an environment
compatible with the maximum operating
ambient temperature (Tma) specified by the
manufacturer (see Specifications information
in this document).
• Place spacers or rubber feet (not provided) on
the bottom of the PCS150R.
• Carefully place the PCS150R on the level
surface.
• To ventilate the system normally and avoid
overheating, leave at least 1 inch (2.5 cm) on
each side (including top and bottom) of the
PCS150R. Do NOT stack other equipment on
the top of the PCS150R.
5
Table of Contents
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . 2
Set the Time Zone. . . . . . . . . . . . . . . . . . . . 24
Important Safety Instructions. . . . . . . . . . . . 3 – 5
Set the Date and Time. . . . . . . . . . . . . . . . . 26
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . 6
Change the Login Password. . . . . . . . . . . . 27
PCS150R Product Description . . . . . . . . . . . . . 7
Update the PCS150R Operating System
via Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setup Information . . . . . . . . . . . . . . . . . . . . . . . 8
Rear and Front Panel Overviews . . . . . . . . . . . 9
Rack Installation . . . . . . . . . . . . . . . . . . . . . . . 10
Typical Rack Installation . . . . . . . . . . . . . . . 10
Rack-mount Considerations. . . . . . . . . . . . . 10
System Setup . . . . . . . . . . . . . . . . . . . . . 11 – 17
Update the PCS150R Operating System
via Serial Link. . . . . . . . . . . . . . . . . . . . . . . . 28
Update the VPN Setup. . . . . . . . . . . . . . . . . 29
Reset the PCS150R. . . . . . . . . . . . . . . . . . . 29
Exit the Current Session . . . . . . . . . . . . . . . 29
Typical Setup Flow Chart for PCS150R
with ASI Output. . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting. . . . . . . . . . . . . . . . . . . . 30 – 31
Typical Setup Flow Chart for PCS150R
with RF Output. . . . . . . . . . . . . . . . . . . . . . . . 12
PCS150R Communication. . . . . . . . . . . . . . 31
Typical Setup Flow Chart for PCS150R
with IP Output . . . . . . . . . . . . . . . . . . . . . . . . 13
VPN Network Connections Overview . . . . . 13
Typical System Installation. . . . . . . . . . . . . . 14
PCS150R Setup. . . . . . . . . . . . . . . . . . . . . . 30
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 32
Document Revision History / Notes . . . . . . . . 33
Open Source Software Notice. . . . . . . . . . . . . 34
Warranty . . . . . . . . . . . . . . . . . . . . . . Back Cover
Network and Communication Setup. . . . . . . . 18
PCS150R Configuration Options. . . . . . . 19 – 29
Log In to the PCS150R and Access
the Main Menu. . . . . . . . . . . . . . . . . . . . . . . 19
View System Information. . . . . . . . . . . . . . . 20
Configure Video Parameters. . . . . . . . . . . . 20
Configure Network Settings. . . . . . . . . . . . . 22
6
206-4157
PCS150R Product Description
The LG PCS150R Pro:Centric ® server is a stand-alone, remotely-controlled processor and
controller for the Pro:Centric system. The server can be used to capture data from an Internet
source, assemble the data as display pages, and output the pages in DTV format over an ASI or
RF interface or an IP stream.
Features
• Three output options: ASI, RF, or IP
• Remote management capability over Ethernet
• Small, lightweight chassis
• 19-inch rack-mountable
• 1U height profile to minimize rack space usage
An Internet browser-based Admin Client graphical user interface (GUI), provided for system
integrator (SI) partners and lodging/institution administrators, facilitates support and maintenance
of the Pro:Centric system. The Admin Client enables users to remotely manage system backups,
output configuration, software updates, portal/information section content, TV configuration
settings, etc.
Note: Design and specifications subject to change without prior notice.
206-4157
7
Setup Information
Check the following items before you begin the PCS150R installation and setup procedures.
ASI Output (Optional)
__ If the system is using ASI ouput, install the modulator and upconverter that will receive the
ASI output signal from the PCS150R. Refer to the manufacturer’s documentation.
PCS150R
__ Unpack the PCS150R Pro:Centric server unit and all accessories.
PCS150R Accessories:
• AC Power Cord and Adapter
__ Select the location for mounting the PCS150R. Ensure that adequate ventilation is
available.
__ Obtain the necessary attachment hardware to mount the PCS150R chassis in its targeted
location.
__ Plan and install the necessary cabling and network (Ethernet) and AC power access for
the PCS150R.
You also will need the following to connect a PC directly to the PCS150R for system setup
verification purposes:
• DB9 Male-to-DB9 Female RS-232 straight-through serial cable (Example: Cables Unlimited
PCM-2100-06 serial cable).
• (Optional) USB 2.0-to-serial DB9 adapter (Example: Cables Unlimited USB-2920 adapter).
If there is no serial port on the PC, use the adapter to connect the serial cable to the PC.
8
206-4157
Rear and Front Panel Overviews
PCS150R Rear View
MODEL: PCS150R
DATE: xx/xx/xx
I IIIII IIIIIIII IIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIII
*201-12150025*
FIRMWARE VER:
R 4.6
RF-OUT
RF OUT
ASI-OUT
ASI OUT
RS-232 Port
Disconnect Device
The AC mains plug is used as the
disconnect device. The disconnect
device must remain readily operable.
RS-232
.........
MAC ADDRESS:
<Eth0>
xx:xx:xx:xx:xx:xx
<Eth1>
xx:xx:xx:xx:xx:xx
ETHERNET-1 / ETHERN
ET-0
USB
POWER-IN
12V DC
USB Ports
NETWORK
(Ethernet) Ports
AC Power
Cord & Adapter
PCS150R Front View
STATUS
STATUS LED
Ventilation Holes
Air flow must not be obstructed. To ventilate
the system normally and avoid overheating,
leave at least 1 inch (2.5 cm) on each side
(including top and bottom) of the PCS150R.
Do NOT stack other equipment on the top of
the PCS150R.
206-4157
9
Rack Installation
Typical Rack Installation
1. Carefully slide the chassis into a standard 19-inch equipment rack.
2. Use all four mounting screws to secure the chassis to the rack.
STATUS
STATUS LED
Rack-mount Considerations
A.Elevated Operating Ambient
If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack
environment may be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum ambient temperature
(Tma) specified by the manufacturer (see Specifications information in this document).
B.Reduced Air Flow
Installation of the equipment in a rack should be such that the amount of air flow required for
safe operation of the equipment is not compromised. To ventilate the system normally and
avoid overheating, leave at least 1 inch (2.5 cm) on each side (including top and bottom) of the
PCS150R. Do NOT stack other equipment on the top of the PCS150R unit. Also, ensure that
the unit’s AC power adapter is never stacked or bundled with other AC power adapters. Each
adapter should have adequate ventilation and should be isolated from other heat sources.
C.Circuit Overloading
Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring.
D.Reliable Earthing
Maintain reliable earthing of rack-mounted equipment. Particular attention should be given to
supply connections other than direct connections to the branch circuit (e.g. use of power strips).
E. Mains Outlet Earthing
The apparatus with Class I construction must be connected to a mains socket outlet with a
protective earthing connection.
10
206-4157
System Setup
Refer to the following diagrams, and complete the system installation as described on pages
14 to 17.
Caution: Do NOT make system connections until instructed to do so during the
system installation procedure. In some instances, configuration steps must be
performed before physical connections are made.
Typical Setup Flow Chart for PCS150R with ASI Output
PCS150R
Network
eth0
eth1
ASI Out
RS-232
RF Out
ASI
Coaxial
Cable
IF In
ASI In
QAM
Modulator
IF Out
RF
Coaxial
Cable
DTV
Upconverter
RF Out
RF
Cable
RS-232 Port
Connection
Laptop
PC
Combiner
RF
Distribution
System
Roo
Receivm
er
Roo
Receivm
er
Roo
Receivm
er
206-4157
11
System Setup (Cont.)
Typical Setup Flow Chart for PCS150R with RF Output
Network
PCS150R
Laptop
PC
RS-232 Port
Connection
eth0
eth1
ASI Out
RS-232
RF Out
RF
Cable
Combiner
RF
Distribution
System
Roo
Receivm
er
Roo
Receivm
er
Roo
Receivm
er
12
206-4157
System Setup (Cont.)
Typical Setup Flow Chart for PCS150R with IP Output
Network
PCS150R
eth0
eth1
ASI Out
RS-232
CAT5E
Cable
RF Out
IP
Distribution
Network
Roo
Receivm
er
Roo
Receivm
er
RS-232 Port
Connection
Laptop
PC
Roo
Receivm
er
VPN Network Connections Overview
Pro:Centric
VPN Server
VPN Client
Internet/
VPN
PCS150R
Laptop
PC
VPN Client
206-4157
13
System Setup (Cont.)
Typical System Installation
(see also Typical Setup Flow Charts and VPN Network Connections Overview diagrams)
1. If your system is using ASI output, make the following two connections; otherwise, go to
step 2.
• Connect a 75 ohm BNC-to-BNC coaxial cable between ASI OUT on the PCS150R and
ASI IN on the modulator.
• Connect an RF coaxial cable between IF OUT on the modulator and IF IN on the upconverter.
Note: The BNC cable must be less than 30 feet (9.2 meters) in length.
2. To enable remote management, connect one end of a CAT5 RJ-45 Ethernet cable to the
ETHERNET-0 port on the PCS150R rear panel, and connect the other end of the cable to the
institution’s network.
3. Connect the PCS150R power supply to the POWER connector on the PCS150R rear panel.
4. Use the straight-through serial cable and, if necessary, the USB adapter to connect a PC to
the RS-232 port on the PCS150R rear panel. (This step will enable you to verify the network
connection once power is applied in step 6.)
5. Using HyperTerminal or an equivalent terminal emulation program on the PC, configure the
serial port as follows: Bits per second = 115200; Data bits = 8; Parity = None; Stop bits = 1;
Flow Control = None
6. Plug the AC power cord into a powered AC line receptacle. When power is applied, the
STATUS LED on the PCS150R front panel will light, and you will see boot-up messages on
the PC.
When the boot-up is complete, a System Information display identifies important information
about the PCS150R, including the unit serial number, hardware ID (firmware version), software
versions, MAC addresses, and IP addresses, for example:
PCS150R Pro:Centric Server v5.2
SN:
Hardware ID: OS version: OS release: Eth0 MAC:
Eth0 IP:
Eth1 MAC:
Eth1 IP:
VPN IP:
RF config:
RF channel: Local time: 001-12150025
1.1.0.17
Linux 2.6.38-zenith+
#204 Mon May 2 17:21:54 CDT 2011
00:0C:63:3B:00:55
192.168.10.77
00:0C:63:3B:00:65
n/a
10.7.0.1
Mode 3, QAM-B, RF: 6 MHz, 5.36 MSps, ASI: 38.81 Mbps
75
Wed Mar 6 16:08:12 EST 2013
(Continued on next page)
14
206-4157
System Setup (Cont.)
(Continued from previous page)
7. Check the Eth0 IP (ETHERNET-0 IP Address) field in the System Information display. By
default, the PCS150R uses DHCP; thus, the DHCP server, if configured, assigns an IP
address to the PCS150R once the PCS150R successfully connects to the network.
• If the Eth0 IP field shows an IP address, the PCS150R is up and running on the network. If
you wish to configure a static IP address for the ETHERNET-0 port and/or if you need to
configure a static IP address for the ETHERNET-1 port (for IP output purposes), continue
with step 8. Otherwise, you can go to step 9 at this time.
• If the network is configured for DHCP, but the Eth0 IP field is blank, refer to “Network
Setup” troubleshooting information on page 30.
• If the network is not configured for DHCP, you will need to configure a static IP address
for the PCS150R ETHERNET-0 port as described in step 8.
8. This step describes how to set a static IP address for the ETHERNET-0 and/or ETHERNET-1
port(s).
Caution: Setting a static IP address for the PCS150R ETHERNET-0 port (for
remote management purposes) is optional. However, if you will be using IP
output from the PCS150R, you MUST configure the ETHERNET-1 port as
described in step (d) below.
a) This step requires that you log in to the PCS150R. Below the initial System Information
display, you should see a login prompt. (If the prompt is not automatically displayed,
press Enter to refresh the screen.)
At the login as: prompt, type admin and press Enter. Then, type the admin user
password (provided by LG) at the password: prompt.
b) At the Command > prompt, type setip and press Enter. The system will display the
current network configuration, followed by the Network Configuration Menu.
Use the Network Configuration Menu commands and follow the system prompts to
configure the port(s). See “Configure Network Settings” on pages 22 to 24 for further
information.
c) Use the “eth0” and “dns” commands to configure the ETHERNET-0 port, as necessary.
d) Use the “eth1” command to configure the ETHERNET-1 port, if required, for PCS150R
IP output. Note the following additional requirements for the eth1 port configuration:
• The ETHERNET-1 port must be configured with a static IP address that is on the same
network as the TV(s).
• Depending on the PCS150R software version, you may be prompted to enter a gateway
IP address. Do NOT specify a gateway IP address for this port. If the prompt for the
gateway IP address shows a default value in square brackets, press the space bar
once and then press Enter to ensure the field remains empty.
(Continued on next page)
206-4157
15
System Setup (Cont.)
(Continued from previous page)
e) When you are finished with network configuration, type exit and press Enter at the
Network Configuration Menu > prompt. The system will display an overview of the new
network configuration and then prompt for confirmation to save the changes:
Do you want to save the new configuration? (Y/N):
Type y or n and press Enter, as appropriate.
Note: Review the New Network Configuration overview carefully before you confirm the
configuration settings. Ensure each of the addresses was entered correctly.
f) If you changed the configuration of the port(s), you will be prompted to reset the system.
At the Command > prompt, type reset and press Enter. The reset process may take up
to two minutes, after which the PCS150R resumes normal operation.
9. (Optional) Set the date and time on the PCS150R.
By default, the PCS150R is synchronized with an NTP client and configured for the US
Eastern time zone. If the PCS150R is connected to the Internet, the NTP client will periodically update the time setting on the PCS150R. You can set the time zone as required. If the
PCS150R is not connected to the Internet, you also have the option to disable NTP client
synchronization and specify date and time data manually.
Note: The Time setup (“time”) command indicated below is available only with PCS150R
version 5.2 or later software. (Check the System Information display header, as necessary,
to verify the PCS150R software version.)
a) This step requires that you log in to the PCS150R.
• If you are already logged in, continue with step (b).
• Otherwise, below the System Information display (after boot-up), you should see a
login prompt. (If the prompt is not automatically displayed, press Enter to refresh the
screen.)
At the login as: prompt, type admin and press Enter. Then, type the admin user
password (provided by LG) at the password: prompt.
b) Use the PCS150R “tz” and/or “time” commands, as necessary, to set the date and time
on the PCS150R.
• Use the “tz” command and follow the system prompts to change the time zone.
• Use the “time” command and follow the system prompts to change the NTP
configuration or manually configure the date and time parameters on the PCS150R.
Refer to “Set the Time Zone” and “Set the Date and Time,” respectively, on pages 24 to 27
for further information on these commands.
(Continued on next page)
16
206-4157
System Setup (Cont.)
(Continued from previous page)
c) If you changed the time zone and/or the NTP configuration, you will be prompted to reset
the system. When you have completed your date and time configuration activities, at the
Command > prompt, type reset and press Enter. The reset process may take up to two
minutes, after which the PCS150R resumes normal operation.
10.Make the appropriate connection to the RF distribution system or IP distribution network
depending on the PCS150R output option to be used.
• ASI output: Connect the RF output on the upconverter to the RF distribution center
combiner, and balance the RF signal so that the Pro:Centric signal level at the TV(s) is
between 0 to +7 dBmV.
• RF output: Connect RF OUT on the PCS150R to the RF distribution center combiner,
and balance the RF signal so that the Pro:Centric signal level at the TV(s) is between 0
to +7 dBmV.
• IP output: Connect a CAT5E or better Ethernet cable between the ETHERNET-1 port on
the PCS150R rear panel and the institution’s IP distribution network.
Caution (ASI/RF Output only): For proper system performance, the Pro:Centric
signal level at the TV input (ANTENNA IN) must be between 0 to +7 dBmV. Note
that additional equipment may be required to adjust the signal level.
11.Configure the ASI/RF or IP output parameters in the Pro:Centric server Admin Client “RF/
IP Configuration” screen. Refer to the Pro:Centric Server Admin Client User Guide for
further information.
Note: By default, the server output is enabled for QAM-B modulation (RF output).
12.Check one or more room receivers to make sure all content is properly mapped and
available.
206-4157
17
Network and Communication Setup
This section describes PCS150R communication options for configuration purposes.
Note: Before you proceed with any additional server configuration, the system
should be installed and operating as described in the system setup procedure on
pages 14 to 17.
Also note that configuration updates periodically require that you reset the PCS150R. Make
sure to reset the unit when directed to do so.
There are two options for communicating with the PCS150R:
• When the PCS150R is connected to an IP network, you can use an SSH client to communicate
with the PCS150R via a command line interface.
• To establish a direct connection to the PCS150R, connect a PC to the RS-232 port on the
PSC150R rear panel using a DB9 Male-to-DB9 Female RS-232 straight-through serial cable
(Example: Cables Unlimited PCM-2100-06 serial cable) and, if necessary, a USB 2.0-to-serial
DB9 adapter (Example: Cables Unlimited USB-2920 adapter).
Using HyperTerminal or an equivalent terminal emulation program on the PC, configure the
serial port as follows:
−− Bits per second/baud = 115200
−− Data bits = 8
−− Parity = None
−− Stop bits = 1
−− Flow Control = None
You will need to know the “admin” user password in order to log in to the command line
interface. If necessary, consult the system administrator to obtain the “admin” user password.
Note: The default network setting for the PCS150R is DHCP, in which case the server assigns
an IP address to the PCS150R. If necessary, consult the network administrator to obtain the IP
address that has been assigned to the PCS150R.
18
206-4157
PCS150R Configuration Options (Cont.)
Log In to the PCS150R and Access the Main Menu
Note: The PCS150R must be connected to an IP network for SSH client access. For direct
access to the PCS150R RS-232 port, use a DB9 Male-to-DB9 Female RS-232 straightthrough serial cable. See also “Network and Communication Setup” on page 18 for further
information.
If necessary, consult the network administrator to obtain the “admin” user password before
proceeding.
1. Establish communication with the PCS150R using an SSH client or via a direct connection
to the PCS150R RS-232 port.
Once communication is established, you should see a login prompt. (If the login prompt is
not automatically displayed, press Enter to refresh the screen.)
2. At the login as: prompt, type admin and press Enter.
3. At the Password: prompt, type the admin password and press Enter.
4. At the Command > prompt, either:
• Press Enter to display the PCS150R Main Menu (see example below).
• Type the desired command and press Enter.
The following sections describe each of the configuration commands.
Note: You can always press Enter at the Command > prompt to display the PCS150R Main
Menu.
Example: PCS150R Main Menu
--------Main Menu
--------info
video
setip
tz
time
pwd
update
updser
vpn
reset
exit
System information
Configure video parameters
Setup TCP/IP
Timezone setup
Time setup *
Change password
Update
Update via serial link
VPN setup
Reset board
End the session
Command >
* Available only with PCS150R version 5.2 or later software.
206-4157
19
PCS150R Configuration Options (Cont.)
View System Information
1. Log in to the PCS150R as described on the previous page.
2. At the Command > prompt, type info and press Enter.
The System Information display identifies important information about the PCS150R, including
the unit serial number, hardware ID (firmware version), software versions, MAC addresses, and
IP addresses, for example:
PCS150R Pro:Centric Server v5.2
SN:
Hardware ID: OS version: OS release: Eth0 MAC:
Eth0 IP:
Eth1 MAC:
Eth1 IP:
VPN IP:
RF config:
RF channel: Local time: 201-12150025
1.1.0.17
Linux 2.6.38-zenith+
#204 Mon May 2 17:21:54 CDT 2011
00:0C:63:3B:00:55
192.168.10.77
00:0C:63:3B:00:65
n/a
10.7.0.1
Mode 3, QAM-B, RF: 6 MHz, 5.36 MSps, ASI: 38.81 Mbps
75
Wed Mar 6 15:10:40 CST 2013
It is recommended that you record this information for future reference. If you find it necessary
to call customer service or engineering support, please have this information available.
Note: If RF output is configured for DVB-C modulation, the display will identify the RF
frequency (in KHz) in place of the RF channel.
Configure Video Parameters
This option enables you to view current settings and/or configure new settings, as required.
1. Log in to the PCS150R as described on the previous page.
2. At the Command > prompt, type video and press Enter.
The system displays the current video parameters and prompts for a selection, for example:
Current video configuration:
1)
2)
3)
4)
5)
6)
7)
Program number
PMT PID
Video PID
Elementary PID1
Elementary PID2
Elementary PID3
Elementary PID4
47 (default)
4096 (default)
4097 (default)
4098 (default)
4099 (default)
4100 (default)
4101 (default)
Select parameter to change or press Enter to accept:
(Continued on next page)
20
206-4157
PCS150R Configuration Options (Cont.)
(Continued from previous page)
3. To return to the Command > prompt without making any changes, you can simply press
Enter. Otherwise, select the appropriate option, depending on the parameter you wish to
change:
• Program Number: Type 1 and press Enter to change the video program number.
At the Enter new value for Program number [47]: prompt, type a new program
number and press Enter. The system will redisplay the video configuration, showing your
update.
Note: The video channel major number is the RF data channel assigned for Pro:Centric
operation (Installer Menu item 119 DATA CHANNEL) and the video channel minor
(program) number is as configured in this step (default program number = 47). Refer to
Commercial Mode Setup documentation for the TV in question for further information.
• PMT ID: Type 2 and press Enter to change the PMT (Program Map Table) PID (packet
ID).
At the Enter new value for PMT PID [4096]: prompt, type the new PMT ID and
press Enter. The system will redisplay the video configuration, showing your update.
• Video PID: Type 3 and press Enter to change the video PID.
At the Enter new value for Video PID [4097]: prompt, type the new video PID
and press Enter. The system will redisplay the video configuration, showing your update.
Note: Assign video and elementary PIDS as necessary according to the system’s
network distribution requirements.
• Elementary PID: There are four Elementary PIDs. Type 4, 5, 6, or 7, depending on which
Elementary PID you wish to change, and press Enter.
At the Enter new value for Elementary PID# []: prompt, type the new
Elementary PID and press Enter. The system will redisplay the video configuration,
showing your update.
Note: Assign video and elementary PIDS as necessary according to the system’s
network distribution requirements.
4. At the Select parameter to change or press Enter to accept: prompt, select
another parameter to change, if desired, and follow the prompts, or press Enter to accept
the displayed configuration parameters and return to the Command > prompt.
206-4157
21
PCS150R Configuration Options (Cont.)
Configure Network Settings
This option enables you to configure the network settings of the PCS150R Ethernet ports.
ETHERNET-0 (eth0) is used for remote communication purposes, while ETHERNET-1 (eth1)
is designated for PCS150R IP output.
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type setip and press Enter.
The system displays an overview of the current network configuration followed by the
Network Configuration Menu, for example:
Current Network Configuration
Interface eth0
Host name:
Using DHCP:
Interface eth1
Host name:
Using DHCP:
DNS servers
Primary DNS:
Secondary DNS:
pcs150r
YES
pcs150r
YES
68.94.156.1
68.94.157.1
-------------------------Network Configuration Menu
-------------------------eth0
Configure eth0
eth1
Configure eth1
dns
Configure dns
exit
Exit network configuration
Choose item to modify >
3. Either:
• Continue with step 4 for information on modifying the configuration a PCS150R Ethernet
port.
• Go to step 9 for information on modifying the DNS configuration.
• To exit the Network Configuration Menu without modifying any settings, type exit at the
Network Configuration Menu > prompt.
4. Type eth0 or eth1, as applicable, and press Enter to modify the configuration of the
ETHERNET-0 or ETHERNET-1 port, respectively.
(Continued on next page)
22
206-4157
PCS150R Configuration Options (Cont.)
(Continued from previous page)
5. At the Host name [pcs150r]: prompt, either press Enter to accept the default value in
square brackets, or type a new host name and then press Enter.
6. At the Using DHCP (Y/N) [Y]: prompt, type y to use DHCP, or type n to specify the
network IP addresses. Then, press Enter. See also note below.
Note: If ETHERNET-1 is to be used for IP streaming, you MUST configure the
port with a static IP address that is on the same network as the TV(s). At the
same time, a gateway IP address should NOT be specified for ETHERNET-1
(see step 7).
7. If the port is NOT using DHCP, type the information requested at each of the following
prompts. Type each address in the format xxx.xxx.xxx.xxx, and press Enter after each entry.
Note: If you are currently configuring ETHERNET-1, depending on the PCS150R
software version, you may be prompted to enter a gateway IP address. Do NOT
specify a gateway address. If the prompt for the gateway IP address shows
a default value in square brackets, press the space bar once and then press
Enter to ensure the field remains empty.
This host IP address []:
Network mask []:
Gateway IP address []:
8. Once you enter (or bypass) the gateway address, the system will redisplay the Network
Configuration Menu.
• To modify the configuration of the second Ethernet port, repeat steps 4 to 7.
• To modify the DNS configuration, continue with step 9.
• If no additional network configuration is required, go to step 10.
9. To change the DNS configuration, type dns and press Enter.
At each of the following prompts, type the information requested. Type each address in the
format xxx.xxx.xxx.xxx, and press Enter after each entry.
Configuring DNS
Primary DNS IP address []:
Secondary DNS IP address []:
Once you enter the secondary DNS IP address, the system will redisplay the Network
Configuration Menu. You can select another option to modify (see previous steps) or you
can exit as described below.
10.When you are finished with network configuration, type exit at the Network Configuration
Menu > prompt. The system will display an overview of the new network configuration
and then prompt for confirmation to save the changes, for example:
(Continued on next page)
206-4157
23
PCS150R Configuration Options (Cont.)
(Continued from previous page)
New Network Configuration
Interface eth0
Host name:
Using DHCP:
Interface eth1
Host name:
Using DHCP:
Host IP address:
Network mask:
Gateway IP address:
DNS servers
Primary DNS:
Secondary DNS:
pcs150r
YES
pcs150r
NO
10.165.60.92
255.255.255.0
68.94.156.1
68.94.157.1
Do you want to save the new configuration? (Y/N):
11.Type y or n and press Enter, as appropriate.
If you opt NOT to save the new configuration, the system will return immediately to the
Main Menu Command > prompt. Otherwise, the system will confirm the configuration
updates and prompt you to reset the PCS150R:
New configuration has been saved. Please restart the system.
12.If you are ready to reset the PCS150R immediately, at the Command > prompt, type
reset and press Enter (see “Reset the PCS150R” on page 29 for further information).
Note: If you intend to modify additional configuration settings during the current session,
you may wait until all changes are complete before you reset the PCS150R.
Set the Time Zone
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type tz and press Enter.
The system displays the current time zone information for the PCS150R and prompts you
to specify whether or not you wish to change the time zone.
Current time zone is: America/New York
Change the time zone? [y/n]:
3. Either:
• Type n and press Enter to return to the Main Menu Command > prompt without changing
the current time zone.
• Type y and press Enter to change the time zone. Then, continue with step 4.
(Continued on next page)
24
206-4157
PCS150R Configuration Options (Cont.)
(Continued from previous page)
4. The system displays the following prompt for a location, followed by a list of options:
Please identify a location so that time zone rules can be set correctly.
Please select a continent or ocean.
At the #? prompt, type the number that corresponds to the appropriate option for your
location, and then press Enter.
5. The system displays the following prompt for a country, followed by a list of options:
Please select a country.
At the #? prompt, type the number that corresponds to the appropriate option for your
country, and then press Enter.
6. The system displays the following prompt for a region, followed by a list of options:
Please select one of the following time zone regions.
At the #? prompt, type the number that corresponds to the appropriate option for your
region, and then press Enter.
After you specify the time zone region, the system displays an overview of your location
selections and prompts for confirmation, for example:
The following information has been given:
United States
Central Time
Therefore TZ=’America/Chicago’ will be used.
Local time is now:
Wed Mar 6 16:23:10 CST 2013.
Universal Time is now: Wed Mar 6 22:23:10 UTC 2013.
Is the above information OK?
1) Yes
2) No
#?
7. Either:
• Type 1 and press Enter if the information in the display is correct. The system will confirm
the setting and then prompt you to reset the PCS150R:
Time zone has been set. Please reset the board.
Continue with step 8.
• Type 2 and press Enter to return to the initial location prompt and reset the time zone
(repeat this procedure from step 4).
8. If you are ready to reset the PCS150R immediately, at the Command > prompt, type
reset and press Enter (see “Reset the PCS150R” on page 29 for further information).
Note: If you intend to modify additional configuration settings during the current session,
you may wait until all changes are complete before you reset the PCS150R.
206-4157
25
PCS150R Configuration Options (Cont.)
Set the Date and Time
Note: This command is available only with PCS150R version 5.2 or later software.
By default, the PCS150R is synchronized with an NTP client and configured for the US Eastern
time zone. If the PCS150R is connected to the Internet, the NTP client will periodically update
the time setting on the PCS150R. If the PCS150R is not connected to the Internet, you also
have the option to disable NTP client synchronization and specify date and time data manually.
See “Set the Time Zone” on page 24 for information on setting the time zone.
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type time and press Enter.
3. At the Synchronize time automatically via NTP? (Y/N): prompt, either:
• Type y and press Enter if you intend to use an NTP client for time synchronization.
• Type n and press Enter to set the time manually.
4. The remaining steps depend on whether or not you opted in the previous step to synchronize
time via an NTP client. Refer to the appropriate subsection below.
Synchronize Time via NTP Client
a) At the Enter a new NTP server IP: [64.90.182.55]: prompt, either press
Enter to accept the default value in square brackets, or type the appropriate NTP client
IP address and press Enter.
b) At the Enter a new NTP update interval, in hours [12]> prompt, either
press Enter to accept the default value in square brackets, or type the appropriate NTP
update interval (in hours) and press Enter.
The system will display confirmation and then prompt you to reset the PCS150R, for
example:
Time will be synchronized every 12 hours via NTP from server: xxx.
xxx.xxx.xxx
Please reset the board
(where xxx.xxx.xxx.xxx is the NTP client IP address you provided above)
c) If you are ready to reset the system immediately, at the Command > prompt, type
reset and press Enter (see “Reset the PCS150R” on page 29 for further information).
Note: If you intend to modify additional configuration settings during the current session,
you may wait until all changes are complete before you reset the system.
Manual Specification of Date and Time
The system will display the current time (for example: Current time: 2013-03-06
18:49:56) and then initiate a series of prompts to enable you to set the time.
(Continued on next page)
26
206-4157
PCS150R Configuration Options (Cont.)
(Continued from previous page)
a) At each of the following prompts, type the year, month, and day, respectively. Note that
all three of these fields require numerical values. Press Enter after each entry.
If applicable, you can also press Enter at each prompt to accept the default value in
square brackets.
Enter new year [2013]>
Enter new month [3]>
Enter new day [6]>
b) At each of the following prompts, type the hour and minute, respectively. Note that the
hour should be entered in 24-hour format. Press Enter after each entry.
If applicable, you can also press Enter at each prompt to accept the default value in
square brackets.
Enter new hour (0-23) [18]>
Enter new minute [49]>
c) The system will display the new time and then prompt for confirmation, for example:
New time: 2013-03-06 18:53:00
Apply? [y/n]
Either, type y and press Enter to apply the new configuration to the system, or type n and
press Enter to return to the Command > prompt without changing the time configuration.
If you apply the new configuration, the system will display confirmation, for example:
Time is set
Change the Login Password
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type pwd and press Enter.
The system prompts for the current password:
Changing password for admin
Old password:
3. Type the current password and press Enter. The system will then prompt you to type and
retype the new password:
New password:
Retype password:
4. Type and then retype the new password at the prompts. Press Enter after each entry.
Once you complete the Password fields successfully, the system displays confirmation:
Password for admin changed by admin.
206-4157
27
PCS150R Configuration Options (Cont.)
Update PCS150R Application or OS Software via Ethernet
Caution: Do NOT initiate simultaneous menu sessions while a software update
is in progress. Doing so may interfere with the active process and may corrupt
the system configuration and/or cause the PCS150R to cease normal operation.
This option enables you to update the PCS150R application or OS software via the Ethernet.
The appropriate update file must be provided by LG; the system will not download an improper
file.
Note: See “Update PCS150R Application or OS Software via Serial Link” below for information on updating software via a serial link.
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type update and press Enter.
3. At the Enter update filename: prompt, type in the update filename and press Enter.
The system will initiate the download and confirm progress, for example:
Downloading file: pcs150r_app_xxxx.upd
4. Follow the system prompts, as necessary, to continue the download.
5. When the update is successfully completed, you may be prompted to reset the PCS150R.
If necessary, reset the server (see “Reset the PCS150R” on the following page).
Update PCS150R Application or OS Software via Serial Link
Caution: Do NOT initiate simultaneous menu sessions while a software update
is in progress. Doing so may interfere with the active process and may corrupt
the system configuration and/or cause the PCS150R to cease normal operation.
This option enables you to update the PCS150R application or OS software via a serial link
to the PCS150R. The appropriate update file must be provided by LG; the system will not
transfer an improper file.
Note: See “Update PCS150R Application or OS Software via Ethernet” above for information
on updating software via the Ethernet.
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type updser and press Enter.
3. At the Send file using XMODEM prompt, transfer the update file using Xmodem
protocol. For example, in HyperTerminal, select Transfer and then Send File.... In the
Send File window, enter or select the appropriate filename in the Filename field, and
select Xmodem in the Protocol field.
The system will display progress messages as well as the result of the update process
(which may take several minutes).
4. When the update is successfully completed, you may be prompted you to reset the PCS150R.
If necessary, reset the server (see “Reset the PCS150R” on the following page).
28
206-4157
PCS150R Configuration Options (Cont.)
Update the VPN Setup
This option enables you to update the VPN client via a serial link to the PCS150R. The
appropriate update file must be provided by LG; the system will not transfer an improper file.
1. Log in to the PCS150R as described on page 19.
2. At the Command > prompt, type vpn and press Enter.
3. At the Send VPN client file using Xmodem ... prompt, transfer the new VPN
client file using Xmodem protocol. For example, in HyperTerminal, select Transfer and then
Send File.... In the Send File window, enter or select the appropriate filename in the Filename field, and select Xmodem in the Protocol field.
The system will display progress messages as well as the result of the update process
(which may take several minutes).
4. When the update is successfully completed, you may be prompted you to reset the PCS150R.
If necessary, reset the server (see “Reset the PCS150R” below).
Reset the PCS150R
1. If not already logged in, log in to the PCS150R as described on page 19.
2. At the Command > prompt, type reset and press Enter.
The reset will be initiated immediately. After reset, the PCS150R resumes normal operation.
Exit the Current Session
At the Command > prompt, type exit and press Enter to end the current session.
206-4157
29
Troubleshooting
PCS150R Setup
The following sections provide basic troubleshooting information for the PCS150R.
Equipment Setup Review
Make sure all connectors and connections are tight and secure on all entertainment system
components.
Network Setup
If the network is configured for DHCP but the PCS150R has not been assigned an IP
address, i.e., the Eth0 IP field in the PCS150R System Information display is blank:
1. Check the ETHERNET-0 connector on the rear panel of the PCS150R. Make sure the
cable connection is tight and secure.
2. Observe the green LED on the ETHERNET-0. Once the PCS150R is connected to the
network, the LED will be lit continuously.
3. Contact the network administrator to verify the network status and check that the DHCP
server is working properly.
30
206-4157
Troubleshooting (Cont.)
PCS150R Communication
If you are unable to establish remote communication with the PCS150R, refer to the
following flow chart.
Cannot Communicate
with PCS150R
To verify the PCS150R IP address:
• If DHCP is enabled, check the router for DHCP IP address
assignments to determine whether the proper IP address is being
used to communicate with the PCS150R.
• If DHCP is not enabled, connect a PC to the PCS150R RS-232
port, display the System Information, and ensure the IP address
shown in the ETHERNET-0 field is the IP address being used to
communicate with the PCS150R. If necessary, update the
ETHERNET-0 configuration as described in this document.
Check that the proper IP
address for the PCS150R
is being targeted. If
necessary, adjust and then
reattempt communication.
Problem
solved?
Yes
End
No
Ensure your PC’s IP address
is on the same subnet as the
PCS150R’s IP address. If
necessary, adjust and then
reattempt communication.
Problem
solved?
Yes
Note: For example, if the PCS150R is
configured with IP address: 192.168.1.x
and Network mask: 255.255.255.0, the
PC’s IP address cannot be: 192.168.2.x.
End
No
Contact LG.
206-4157
31
Specifications
Dimensions
Height:
Width:
Depth:
Weight:
1.692 inches (42.977 mm)
19.0 inches (482.6 mm) (for EIA standard 19-inch rack mount)
8.5 inches (215.9 mm)
3.45 pounds (1.56 kgrms) rack-only weight
Environmental Storage Conditions
Temperature:
-20° to 70° Celsius
-4° to 158° Fahrenheit
Humidity:
95% non-condensing
Environmental Operating Conditions
Temperature (Tma): 0° to 40° Celsius
32° to 104° Fahrenheit
Humidity: 95% non-condensing
Electrical
RF Out Connector:
Frequency:
Active Output Level at RF Out jack: Frequency Accuracy:
75 Ohm, Type ‘F’
VHF/UHF 54–864 MHz
-6 dBm (+42 dBmV) Min., -2 dBm (+46 dBmV) Typ.
±5 ppm
Impedance at ASI Out jack: Level at ASI Out jack: 75 Ohms
800 mv
DC Input: +12V DC @ 4.0 Amps
Ethernet Connectors (2):
10/100/1000BaseT
USB Ports (2):
USB 2.0
Modulation Specifications
Standard:
ITU-T J.83 Annex B (QAM-B)
Constellations:
256-QAM
Symbol Rate:
256-QAM
5.360537 MBaud
Interleaving:
Fixed I = 128, J = 1
Standard:
DVB-C
Constellations:
64-QAM, 256-QAM
Symbol Rate:
64-QAM
6.9 MBaud
64-QAM
6.111 MBaud
256-QAM
6.9 MBaud
256-QAM
6.111 MBaud
Note: Design and specifications subject to change without prior notice.
32
206-4157
Document Revision History / Notes
Document Revision History
Date
Description
May 2011
Revision A: New document
June 2013
Revision B: Configuration and specifications updates
Product documentation is available online at: www.LGsolutions.com.
Notes
206-4157
33
Open Source Software Notice
The following GPL executables and LGPL libraries used in this
product are subject to the GPL Version 2.0/LGPL Version 2.1
License Agreements:
GPL EXECUTABLES: Linux kernel 2.6.33, LTIB 10.1.1,
bash-2.05b, busybox-1.1.3, e2fsprogs-1.34, ethtool-3, gawk3.1.3, lrzsz_0.12.21, lzo-2.03, mtd-utils-1.2.0, net-tools-1.60,
ntpclient_2003_194, openvpn-2.1.1, pciutils-2.1.11, ppp-2.4.1,
procps-3.1.11, screen-4.0.2-1, skell-1.13, time-1.7
LGPL LIBRARIES: eglibc 2.8, libelf-0.8.5, termcap-2.0.8
To obtain the source code under GPL, LGPL, MPL and other
open source licenses that are contained in this product, please
visit http://opensource.lge.com. In addition to the source code,
all referenced license terms, warranty disclaimers and copyright notices are available for download. LG Electronics
will also provide open source code to you on CD-ROM for a
charge covering the cost of performing such distribution (such
as the cost of media, shipping and handling) upon e-mail
request to opensource@lge.com. This offer is valid for three (3)
years from the date on which you purchased the product.
You can obtain a copy of the GPL, LGPL licenses from: http://
www.gnu.org/licenses/old-licenses/gpl-2.0.html and http://
www.gnu.org/licenses/oldlicenses/lgpl-2.1.html.
This product includes:
• OpenSSH-4.3p2:
Copyright © 1994, 1995 Tatu Ylonen, Espoo, Finland
Copyright © 1998 CORE SDI S.A., Buenos Aires, Argentina
Copyright © 1995, 1996 by David Mazieres
Copyright © 1980, 1983, 1987, 1988, 1990, 1992, 1993,
1995 The Regents of the University of California
Copyright © 1999, 2000, 2001, 2002, 2003, 2004 Markus
Friedl
Copyright © 1995, 1996, 1998, 1999 Theo de Raadt
Copyright © 1999, 2000, 2001, 2002 Niels Provos
Copyright © 1999 Dug Song
Copyright © 1999 Aaron Campbell
Copyright © 1999, 2000, 2001, 2002, 2003, 2004, 2005
Damien Miller
Copyright © 2001 Kevin Steves
Copyright © 2002 Daniel Kouril
Copyright © 2003 Wesley Griffin
Copyright © 2001 Per Allansson
Copyright © 2002, 2003 Nils Nordman
Copyright © 2001-2003 Simon Wilkinson
Copyright © 2000, 2001 2003 Ben Lindstrom
Copyright © 2002, 2005 Tim Rice
Copyright © 2000 Andre Lucas
Copyright © 2002 Chris Adams
Copyright © 2000, 2001 Corinna Vinschen
Copyright © 2002 Cray Inc. (Wendy Palm)
Copyright © 2000 Denis Parker
Copyright © 2001 Gert Doering
34
Copyright © 2001, 2003 Jakob Schlyter
Copyright © 1996 Jason Downs
Copyright © 2002 Juha Yrjölä
Copyright © 2000 Michael Stone
Copyright © 2002 Networks Associates Technology, Inc.
Copyright © 1997, 1998, 2000-2002, 2004 Todd C. Miller
Copyright © 2003, 2004, 2005 Darren Tucker
Copyright © 1988-2002 Sun Microsystems, Inc.
Copyright © 2005 The SCO Group
Copyright © 2004 The OpenBSD Project
Copyright © 2005 Anil Madhavapeddy
Copyright © 1994 Phil Karn
Copyright © 1996-1998, 2003 William Allen Simpson
Copyright © 2003 Peter Stuge
Copyright © 2005 Reyk Floeter
Copyright © 1991 Massachusetts Institute of Technology
Copyright © 2004 Ted Unangst and Todd Miller
Copyright © 1999 WIDE Project
Copyright © 1996 Internet Software Consortium
Portions Copyright © 1999-2001 Internet Software Consortium
Portions Copyright © 1993 Digital Entertainment Corporation
Portions Copyright © 1995 International Business Machines,
Inc.
• OpenSSL-1.0.0:
Copyright © 1998-2008 The OpenSSL Project
Copyright © 1995-1998 Eric Young
All rights reserved.
Permission is hereby granted, free of charge, to any person
obtaining a copy of this open source software and associated
documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights to
use, copy, modify, merge, publish, distribute, sublicense, and/
or sell copies of the Software, and to permit persons to whom
the Software is furnished to do so, subject to the following
conditions:
SUBJECT TO THE TERMS OF THE GPL VERSION 2.0/LGPL
VERSION 2.1 LICENSE AGREEMENTS, THE SOFTWARE IS
PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR
A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN
NO EVENT SHALL THE AUTHORS, COPYRIGHT HOLDERS,
OR LG ELECTRONICS (THE “LICENSOR”) BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE, EVEN IF LICENSOR HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. LICENSEE
ASSUMES THE COST OF ALL NECESSARY SERVICING,
REPAIR, OR CORRECTION.
206-4157
LG PCS150R Pro:Centric Server Warranty
Broadcast Products Welcome to the LG family! We believe that you will be pleased with your new PCS150R Pro:Centric Server. Please read
this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal
rights, and you may also have other rights that vary from state-to-state within the U.S.A.
LG’s RESPONSIBILITY
Warranty Term
Parts
Warranty Service
Not Covered
One year parts and labor from date of purchase or delivery date.
New or remanufactured replacements for factory-defective parts may be used. Such replacement parts are warranted for
the remaining portion of the original warranty period.
Warranty service is provided at LG. Customer pays for shipping charges to LG; LG pays for return shipping charges to
return PCS150R Pro:Centric Server to customer. Call 1-888-865-3026 for further information.
This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation
or repair of antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due
to misuse, abuse, negligence, acts of God or other causes beyond the control of LG. Any alteration of the product after
manufacture voids this warranty in its entirety.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND LG SHALL NOT BE
LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST
REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
OWNER’S RESPONSIBILITY
Effective Warranty Date Warranty begins on the date of delivery of the PCS150R Pro:Centric Server.
For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date.
Installation Guide
Read the Installation & Setup Guide carefully so that you will understand the operation of the PCS150R Pro:Centric Server
and how to adjust the settings.
For warranty service information, call 1-888-865-3026. Parts and service labor that are LG’s responsibility (see above)
will be provided without charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory
warranty service, call 1-888-865-3026.
You must provide the model number, serial number and date of purchase or date of original installation.
Warranty Service
For Customer Support/Service, please call:­­
1-888-865-3026
www.LGsolutions.com
Pro:Centric is a registered trademark of LG Electronics U.S.A., Inc. All other
trademarks or registered trademarks are the property of their respective owners.
 Copyright 2013 LG Electronics U.S.A., Inc.
206-4157
Revision B
Download PDF
Similar pages